installing a hearing loop in - wordpress.com · 12/09/2017 · what is hearing loop? the...
TRANSCRIPT
1
INSTALLING A HEARING LOOP IN
YOUR HOME… or…
Instructor
“Loop’n Lou” Touchette2
What is Hearing Loop?
The “loop” is a wire routed around a room. Anyone
within the “Loop” wearing a telecoil equipped
hearing aid or using a Loop Receiver will hear
what is transmitted by the loop amplifier.
The telecoil senses this energy field. The computer
function of your hearing aid converts this energy
back into “corrected” audible sound.
3
4
Hearing aid or CI Processor with a Telecoil
5
6
Looping a Room
7
Loop Layout
8
Loop Amplifier (Rear View)
9
What wire size to use
(Use the manufacturers recommendations or
use these general rules)
• Wire up to 80’ in length, use AWG 22 gauge
• Wire 80 to 120’ in length, use AWG 20 gauge
• Wire 120 to 200’ in length, use AWG 18 gauge
• Wire can be bought at Electrical supply stores
10
Installation of wire
1. How high above the floor should a loop wire be
located?
Ideally the wire should be at the floor or 8’ above (4’ above
or below the hearing aid of a seated person). Any higher
than 8’ a drop in signal strength may be noted. In order to
keep signal strength uniform, the wire should always be maintained at the same height around the room.
11
Installation of wire (cont’d)
2. What different ways can a loop wire be installed?
• The loop wire can be run overhead attached to the
ceiling or wall at the joint line.
• It can be run around the baseboard and routed up over
doorways or under carpet.
• Placed in the ceiling of the floor below
• Placed under an area rug.
•In any installation the wire will complete a loop before
being attached to the amplifier.
12
Installation of wire (cont’d)
3. How do I run the loop wire around the
baseboard?
• The loop wire can be run above the baseboard or
tucked under it.
• At doorways you can route the wire up and over the
door frame or under the threshold. If the floor is
carpeted, you can use a box knife to cut a 1” slit in the
carpet and run the wire under the carpet to the other
side of the doorway (fish tape, or a coat hanger
straightened out with a loop on each end can be used
as a needle.)
13
Installation of wire (cont’d)
4. Can I paint my loop wire?
• Many people have painted the loop wire to
match their wall color. This does not harm the
wire or affect the quality of your signal strength.
• Loop wire comes in about six basic colors with
white being the most popular.
14
Installation of wire (cont’d)
5. Things to avoid
• Never run a loop wire near or against a metal
object for more than a few feet as metal can suck
up some of the loop signal strength.
15
6. Can I “Mute” a loop?
Small loop amplifiers do not come with a muting capability. If you want to mute commercials, you can buy a “Wireless Lamp Switch” (about $10 at Home Depot). Plug the loop amplifier into it and using the included remote control, turn off the loop during commercials.
16
Connecting a Wireless Microphone
17
Loop Pad Kit
18
• Loop pads (aka “Chair” pad) are great when a room design is such that a
loop wire cannot be installed. The pad is placed under a chair so a person
can hear while seated above it. The “pad” can be used when traveling
(offering portability).
Using Loop Pad instead of Loop Wire
19
Non-standard connections
TV’s without RCA “Audio Out” jacks.
• Attach flat-round microphone to the front of the TV speaker
grill. Plug into the microphone jack on the loop amplifier.
• If using a cable box, satellite receiver, TIVO or DVR, use
the Red and White RCA “Audio Out” jacks
• If the TV has an earphone jack, you can use it, but it will
mute the sound from the TV’s speakers.
• Some newer HDTV’s require use of Digital-Audio-
convertors (DAC).20
Digital Optical to Analog Converters
21
22
Adjusting the loop signal strength
• Sit in your favorite chair chair then have
someone adjust loop volume to a comfortable
level for you. (Give thumbs up for more volume
or thumbs down for less)
• For best sound (Highs, mid range and bass) a
pleasant 50-50 blend of loop and TV volume
should be obtained.
23
Common questions
1. I can hear the loop when I’m in an adjacent
room. Why is this?
What you are experiencing is referred to as
“Spillover.” The range can vary but it is rare that
you’ll notice this beyond about 4 to 6 feet
outside of the loop.
24
Common questions
2. I have to cock my head up or down to hear
the loop. Why is this?
Hearing aid manufacturers install telecoils in any
open space they can find within the hearing aid.
The orientation of your telecoil may be tilted and
is most likely causing this to happen…... ie
Cochlear America N5 and N6 processors
25
Common questions
3. I have my home loop set at a comfortable level, but
when I go to different looped public locations, the
volume is always either too low or too high. Why the
difference?
Public places are required to have the loop volume set to an
international standard of zero plus or minus three decibels.
In newer digital hearing aids the telecoil volume can be
adjusted by your hearing professional so that you hear in
those public places. After being adjusted, readjust your
home loop again so it is comfortable for you.
26
Common questions
4. Can I take my loop system with me when I
travel?
Absolutely! Some loop amplifiers have optional
“Loop Pads” that have a long cords on them. You
can take your amplifier with you and use it in motel
rooms … or. Uncoil the loop pad and place under
you’re a pillow, bed or chair. Then connect the RCA
patch cord or use a microphone to hear the TV.
27
Common questions
5. I often have company and have a hard time
hearing them. Can I somehow use my loop to
hear them when they are speaking?
There are both lapel and wireless microphones that can be plugged into most loop amplifiers. Simply have your guest(s) speak into the microphone and you’ll be able to hear them through the loop.
28
Common questions
6. Can I connect my telephone to the loop
system?
Yes, there are several types of Telelink Adapters
available that will work well with the loop. This is
an excellent invention. There’s also a suction
cup microphone that can be suctioned to the
handset and connected to the amplifier.
29
30
Telelink Adapter
31
This type will work
with cordless tele-
phones, also.
32
Works with a single
telephone, only.
Common questions
7. Can I use my loop system in my Recreation
Vehicle (RV) or automobile?
Loop amplifiers can be installed in both RV’s and
automobiles. Use an optional DC adapter to plug
into the cigarette lighter receptacle.
Don’t buy multiple loop amplifiers. Just share the
one from your home with the RV or automobile as
needed.
33
Common questions
8. Will “BlueTooth” work with a loop??
- BlueTooth is a wireless technology that works
independently of a loop.
- To use it for TV, connect a cord from the TV audio
out to the BlueTooth streamer (basically, it’s a
wireless transmitter).
- HOWEVER, Some BlueTooth microphones have
telecoils that will allow listening through a loop.
34
35
Troubleshooting
Causes of EMI (buzzing sound in the loop)
•Fluorescent lighting ballasts
•Light rheostats(dimmers)
•Cathode Ray Tube (CRT) older TV’s/monitors
NOTE: Newer HDTV’s do not emit Electro
Magnetic Interference (EMI). To test for EMI, turn
on your telecoil and walk around the room
listening for any buzz or humming sounds..
36
Thank you for attending this class!
• NOTE:
• There’s a MAJOR shortage of home loop/Small area installers across America. Perhaps HLAA should offer more of these looping classes to the public.
• Many sources for buying looping equipment can be found on the Internet.
37
38
Where can I purchase Assistive
Listening Devices ( ALD’s)
http://www.harriscomm.com/
https://adcohearing.com/
http://www.lssproducts.com/
Or, You’ll find these above sites and more if you just GOOGLE search
specific items such as “Loop Equipment, PockeTalker, Telelink
Adapter, FM Systems, Headphones, Neckloops, Microphones,
etc…”
QUESTIONS?
39