installing one flexi multiradio 10 bts capacity extension sub-module (fbba)

7/25/2019 Installing One Flexi Multiradio 10 BTS Capacity Extension Sub-Module (FBBA)

http://slidepdf.com/reader/full/installing-one-flexi-multiradio-10-bts-capacity-extension-sub-module-fbba 1/5

Installing one Flexi Multiradio 10 BTSCapacity Extension Sub-Module (FBBA)

Стр. 1 из 5

24.08.2015http://localhost:9090/informationbrowser/advanced/print.jsp?topic=/m88653279 html...



isclaimer

The information in this document is subject to change without notice and describes only the productdefined in the introduction of this documentation. This documentation is intended for the use of NokiaSolutions and Networks customers only for the purposes of the agreement under which the document issubmitted, and no part of it may be used, reproduced, modified or transmitted in any form or meanswithout the prior written permission of Nokia Solutions and Networks. The documentation has beenprepared to be used by professional and properly trained personnel, and the customer assumes fullresponsibility when using it. Nokia Solutions and Networks welcomes customer comments as part of theprocess of continuous development and improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity, orperformance of the mentioned hardware or software products are given "as is" and all liability arising inconnection with such hardware or software products shall be defined conclusively and finally in a

separate agreement between Nokia Solutions and Networks and the customer. However, NokiaSolutions and Networks has made all reasonable efforts to ensure that the instructions contained in thedocument are adequate and free of material errors and omissions. Nokia Solutions and Networks will, ifdeemed necessary by Nokia Solutions and Networks, explain issues which may not be covered by thedocument.

Nokia Solutions and Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SOLUTIONS AND NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL,DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOTLIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITYOR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights and otherintellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Solutions and Networks Only. Nokia is a registered trademark ofNokia Corporation.

Other product names mentioned in this document may be trademarks of their respective owners, andthey are mentioned for identification purposes only.

Copyright Â© Nokia Solutions and Networks 2012. All rights reserved.

Installing one Flexi Multiradio 10 BTS Capacity Extension

Sub-Module (FBBA)

Before you start

When using only one FBBA, connect it to BB EXT1 (left-hand side) port on FSMx core.

1 Remove the dummy unit as follows:

a. Remove the side flange.

b. Remove the middle flange between the dummy units.

c. Pull out the dummy unit.

Leave the other dummy units in place if you are not installing any other optional sub-modules.

Стр. 2 из 5




Figure 32. Removing FBBA dummy unit

2 Insert the extension sub-module.

Figure 33. Inserting FBBA

Стр. 3 из 5




3 Fix the middle flange back in place between the extension sub-module and the remaining dummy unit.

Make sure you install the middle flange as shown in Figure 34: Fixing FBBA and dummy unit. Tighten the screws as follows:

• Dummy unit (plastic): 0.8 Nm (0.59 ft-lb)

• Metal parts: 2.4 Nm (1.77 ft-lb)

Figure 34. Fixing FBBA and dummy unit

4 Fix the side flange back in place.

Tighten the screws to 2.4 Nm (1.77 ft-lb).

Figure 35. Fixing side flange

Стр. 4 из 5


installing one flexi multiradio 10 bts capacity extension sub-module (fbba)

Documents