Ammunition reloading can be dangerous if done im properly and can result in serious injury or death.

· Reloading should not be attempted by persons not willing and able to read and fol low instructions exactly. · Children should not be permitted to reload ammunition without strict parental supervision. · Always wear safety glasses and hearing protection when reloading and shooting. · Ammunition loaded with these tools and data should only be used in modern guns in good condition. · We do not accept responsibility for ammunition loaded with these tools or data as we have no control over the manufacture and storage of components or the loading procedure and techniques. · Primers and gun powders, like gasoline and matches, can be dangerous if improperly handled or misused.

DANGER

PR14

41

1

AUTO BREECH LOCK PRO | PRO 4000 KITI N S T R U C T I O N S

LARGETP3796

SMALLTP1332

CAUTION

DISPOSAL TUBE # BP3064CAP # BP3127 RAM PIN # OF3221

LINK BOLT (qty. 2) # TP2117

CONNECTING LINK #TP2129

LEVER CLAMP # OF3613

1 3/16” WASHER # OF3609

5/16 –18 X 1 1/4 BOLT# FO2113

SLIDER BLOCK

CASE FEED SPRING# PR2118

TOOL HEAD# PR2050

(NOT PICTURED)

1/4-20 X 5/16 PHIL. PAN. # FQ1869

INDEX ROD# PR3716

CASE RETAINER#PR3691

CASE EJECTOR#PR3691

PRIMER ARMS

(NOT PICTURED)

LINK NUT (qty. 2)# FB1181

CARRIER COVER# PR3692

CARRIER CORE# PR3711

CASE RETAINER SCREWS (3) 6-19 X 1/4 PAN HD PLASTITE #FP2111(NOT PICTURED)

CASE RETAINER O-RING (3)#PR2039

BASE # TR3642

TOGGLE (qty. 2) # OF2853

RAM#PR3717

PRIMER OUTLET # TP3707

# PR3691 molded parts

# PR3692 molded parts

HELP VIDEOS

LUBRICATION POINT

LUBRICATION POINT

LUBRICATION POINT

Install driver clutch when no shell plate is installed.

Install driver clutch when shell plate is installed.

Unable to index? Verify driver clutch is installed.

LEE PRECISION, INC.4275 Hwy. U · Hartford WI 53027www.leeprecision.com

Press includes Spline Drive Breech Lock bushings, leave them in place or order additional for quick change convenience. New, easy grip splined drive surface allows easy, accurate, and fast die installation in your press. Color coded for quick positive identification. Lock rings are not required on your dies when utilizing these bushings.

90063 2-PACK 90042 3-PACK 90095 4-PACK

Spline Drive Breech Lock Bushings

RETAINER PLATE# PR3692

PRO 4000 KIT SHOWN

Auto-Drum powder measure# 90811

Universal Case Feeder# 90242

Bin & Bracket# 90687

Safety Prime# 90997

Die wrench included

Works on spline drive breech lock bushings and lock rings.

Replace carrier cover help video ▼

LUBRICATION POINTS= use STP™ motor treatment or motor oil.

2

1 2

3

Mount your press. The most convenient way to mount your press is with our Lee Bench Plate System # 90251. This system includes all of the mounting hardware and allows for quick press removal without unbolting from bench. Or, purchase (qty. 3) ¼” bolts and nuts and prepare your workbench for use with this press using the drill template provided on the quick start guide attached to your press

# 90251 Bench Plate

SAFETY CONSIDERATIONS• Be sure of proper powder and charge for

bullet weight selected.• Wear safety glasses and hearing

protection when reloading or shooting.• Be extremely careful to avoid a double

charge. If in doubt, empty the case and recycle it.

• Do not permit distractions while loading. This is a complex machine that needs your fullest attention.

SMOOTH OPERATING TIPS• Always move the lever smoothly in

complete strokes. An interrupted stroke can cause a jam or double charge.

• Do not force it or you will break something. If it does not feel right, stop and check out the problem.

• Oil ram using STP™ motor oil treatment. Using any oil, lubricate link bolts and ram pin every few thousand rounds.

SETUP TOOLS REQUIRED• Safety glasses & ear protection• �” socket or wrench• 3/32” hex key (also available as an accessory # 91634)

HELPFUL SETUP VIDEOSOpen camera application on smartphoneor tablet, hover over the QR code for a direct link to help video.

INSTALL shell plateB C

Remove Spline Drive breech lock bushing.

A

Re-position handle, tighten securely with �” socket or wrench.

Remove index rod and case ejector.

INDEX RODINDEX ROD

CASE CASE EJECTOREJECTOR

Raise carrier to the mid-stroke position, install shell plate, lightly tighten clockwise with ¼” hex head wrench.

STEPS 1-6 BELOW ARE COVERED IN QUICK-START GUIDE ATTACHED TO YOUR PRESS

E F

Push case retainer against case rim in each shell plate position

D

Install case ejectorWith the carrier at the bottom of the stroke (handle up), install index rod.

Install Spline Drive breech lock bushing.

G

HELP VIDEOS

VIDEO

Verify the handle passes completely through lever clamp.

3

5

6

TOOL HEAD POSITION & INITIAL SETUP

Position 2 =Powder Through Expanding Die orRifle Charging DieLower the lever, the case will rise into the powder charging/pistol expanding station to dispense a charge.

priming position

Position 1 = SizeI M P O R TA N TVerify this die is installed as follows:Remove lock-ring. Screw the die in until it touches the shell plate. Lower the ram, and screw die in ⅓ turn more. Tighten the hex screw on the spline drive bushing with 3/32 hex key. Place a case through the feed hole or the case feeder, and lower the press lever to insert case into the shell plate to be sized. This will punch out the spent primer and size the case back to factory specifications.

Position 3 = Bullet Seating DiePut a loose bullet on top of the case mouth. Lower the lever, this will raise the case into the bullet seating/crimping die to seat the bullet.

The Auto Breech Lock Pro will automatically index with cartridges up to 2.30” (58mm) long. Removing the index rod and manual indexing allows loading most longer action rifle cartridges like the 30/06. Not having the auto index makes the press just as efficient as the popular and expensive Dillon 550™.

Install reloading dies according to the instructions provided with your reloading dies. We suggest Lee dies as they use a powder through expanding die to conveniently charge your brass while expanding the case mouth. Lock rings are not required when utilizing the spline drive breech lock bushing in either station.

7

INSTALL appropriate primer armRaise ram to mid-stroke position. Install primer arm in the carrier.

PrimeWith clean fingers, place the correct size and type of primer into the primer guide. Or dispense primer using the OPTIONAL

Lee Safety Prime primer feeder (never touch the primer from box to shell). Raise the lever, seat the primer to flush to slightly below flush

of the case head.

4

LARGESMALL

case feed hole

Position 4 = Factory Crimp Die firmly crimps your bullet in place and will give your round factory like feed and dependability.

1

2

3

4

Raise the retaining ring and slide the primer collection tube assembly into the ram. Slide retaining ring on to assembly.

5 Install OPTIONAL bin and bracket # 90687

Mount to leg of Lee reloading stand using provided 1/4-20” bolts and 1/4”-20 nuts

Mount to workbench using (2) provided # 8 Phillip Head Screws.OR

If you haven’t reloaded before, we suggest you start out using the Auto Breech Lock Pro as the world’s most convenient single station press. Simply install your sizing die in position one and you’re ready to go. Keep your right hand on the roller handle, cycle the lever to the bottom of the stroke. Pick up a case with your left hand and drop it into the case feed hole next to position one, grab a single primer and place in the primer cup. Raise the lever and the case will be slid into the shell plate and the primer will be seated at the bottom of the stroke (lever up) Lower the lever and the case will enter the sizing die. Drop another case into the case feed hole another primer in the primer cup and repeat the cycle.

You can also operate as you would a Lee turret press and produce a complete round with four cycles of the lever. Install the 3 or 4 dies in the press as shown above. Drop an empty case into the feed hole and cycle the lever four times. A single case will advance through the four stations. You will insert a primer in the priming arm, dispense a powder charge into the powder through expanding die, place a bullet into the flared case and cycle the lever a forth time to Factory Crimp and automatically eject the finished round.

With a die in every position, you can use the press as a full progressive by simply placing a case in the feed hole every cycle of the lever. Because each station performs one operation, every time you cycle the lever you produce a finished round. If you operate the lever at a leisurely 10 seconds per cycle that is 360 rounds an hour.

primer cup

Available accessory # 91634 3/32 hex key

Available accessory # 91634 3/32 hex key

4

CARTRIDGE SETUP

CARTRIDGE SHELL PLATE

SHELL PLATE PRODUCT #

PRIMER ARM UNIV. CASE FEED PLATE SIZE

UNIV. CASE FEED SLIDER BLOCK

RELOADING DIES CHARGING DIE

30 LUGER 19 90944 SMALL SMALL 90754

30 MAUSER 19 90944 SMALL SMALL 90755

7.62 TOKAREV 19 90944 SMALL SMALL 90769

32 ACP 7 90647 SMALL SMALL 90622

32 S&W 4 90630 SMALL SMALL 90696

32 S&W LONG 4 90630 SMALL SMALL 90624

32 H&R MAG / 327 FED 4 90630 SMALL SMALL 90809

9MM LUGER 19 90944 SMALL SMALL 90332

9MM MAKAROV 19 90944 SMALL SMALL 90176

357 SIG 19 90944 SMALL SMALL 90270

38 SUPER 19 90944 SMALL SMALL 90623

38 S&W 1 90582 SMALL SMALL 90569

38 COLT NP 1 90582 SMALL SMALL 90569

380 AUTO 4 90630 SMALL SMALL 90092

38 SPL & 357 MAG 1 90582 SMALL SMALL RISER 90615

38 ACP 19 90944 SMALL SMALL 90623

38 SHORT/LONG COLT 1 90582 SMALL SMALL 90276

40 S&W 19 90944 SMALL SMALL 90571

10MM AUTO 19 90944 LARGE SMALL 90566

41 MAG 9 90278 LARGE LARGE RISER 90628

44 SPL & 44 MAG 11 90648 LARGE LARGE RISER 90604

400 COR BON 2 90584 LARGE LARGE 90430

30M1 CARBINE 7 90647 SMALL SMALL RISER 90626

44 RUSSIAN 11 90648 LARGE LARGE RISER 90293

454 CASULL 11 90648 SMALL LARGE RISER 90795

45 ACP 2 90584 SMALL OR LARGE LARGE 90233

45 COLT 11 90648 LARGE LARGE RISER 90265

45 GAP 2 90584 LARGE LARGE 90498

460 S&W 14 90802 LARGE LARGE RISER 90344

50 ACTION EXPRESS 11 90648 LARGE N/A N/A 90329 (LUBE REQ.)

223 REM 4 90630 SMALL SMALL RISER 90253 (LUBE REQ.) 90668

222 REM 4 90630 SMALL SMALL RISER 90501 (LUBE REQ.) 90668

458 SOCOM 2 90584 LARGE N/A N/A 90409 (LUBE REQ.) 90668

6.8 REM SPC 21 90941 LARGE SMALL RISER 90427 (LUBE REQ.) 90668

To convert the Auto Breech Lock Pro from a one cartridge to another, you will need the proper shell plate and appropriate Lee reloading die set. The chart below shows proper configuration with catalog numbers.

N/A = Not available LUBE REQ. = # 90006 LEE resizing lubricant required

8

Assembled as a SMALL feed plate

Bolt and nuts are adjacent to small through hole and the small plug.

small small holehole

small plug installed

large large holehole

Assembled as a LARGE feed plate

small plug removed

storage spot for small plug

Feed plate setup for Universal Case Feeder, accessory sold separately # 90242

Universal Case Feeder# 90242

5

INSTALLING Universal Case Feeder, accessory sold separately # 90242

A B

C

See chart on page 4. Install the correctly configured feed plate (large or small) keeping the bottom of the case feed plate a pennies thickness above the case mouth. Slide a case through feed plate. Place penny on top of the case, slide feed plate into carrier.

The 4 tube feed plate should be a penny’s thickness away from the tool head casting. Verify a coins thickness away from body.

Secure the feed plate with a nut above and below the carrier slide rail. Tighten 7/16” nuts under and above carrier.

Case slider blockCase slider block

RiserRiser

See chart on page 4. Some cases require riser to be installed on top of case slider block.

Slide the RISER block on top of CASE SLIDER BLOCK until the front and back are flush. Tighten Phillips screw on riser block.

A penny’s thickness above case mouth

This accessory will greatly simplify progressive reloading placing a case every time the press is cycled. The case slider block is already on your press. Longer cases will require you to attach the riser to the case slider block. All you need to do is install the feed plate configured for the case that you will be loading.

Consider the case collator product # 90667 fill all four case feed tubes in as little as 10 seconds.

Case Collator# 90667

D

INSTALLING Safety Prime, accessory sold separately # 90997Dispenses primers with a push of the button. Works with all brands of primers and you never have to handle the tiny primers. Fill the tray in seconds rather than filling a tube one at a time like other brands.

Safety Prime # 90997

A B Install the triangular shaped bracket as shown. Rotate the bracket left to right to best align the trigger and trough with the primer arm.

With the carrier at the top of the stroke (lever down) swing the primer trough into the primer arm and push the trigger. Be sure you install the correct primer arm (large or small) and that you have selected the correct trigger assembly (large or small)

LARGESMALL

Case feeding, primer feeding, powder measuring and bullet feeding can be automated with the addition of optional Lee accessories.

I M P O R T A N T Only use the Safety Prime manufactured after June 2017. This version can be identified by the light gray color and serrated trigger.

VIDEO

VIDEO

30 & 32 cal. Bullets up to .60 long # 908929mm through .365 diameter up to .46 long # 908939mm through .365 diameter .46 to .60 long # 908949mm through .365 diameter .60 to .75 long # 9089540 cal. through .44 cal. up to .65 long # 9089640 cal through .44 cal .65 to .80 long # 9089745 cal. bullets .50 to .67 long # 90898

LEE BULLET FEEDER OPTIONALAutomatically feeds bullets into the mouth of the seating die. Aligns bullets more accurately than possible by hand. Increases cyclic rate 50 to 100%.

Auto-Drum Powder Measure# 90811

Pro Auto-Disk Powder Measure# 90429

INSTALLING Automatic Powder Dispenser accessoryFor volume reloading, nothing beats a Lee Auto-Drum or Pro Auto-Disk or powder measure. Either of these automatic powder measures will dispense a powder charge through the Lee powder through expanding die. They are automatic and will only dispense a powder charge if they are activated by a case.

A If you are using the pull back feature on the Auto-disk, the chain is installed through this lug.

INSTALLING Automatic Bullet Feeder accessoryRECOMMENDED FOR ADVANCED USERS ONLY. Incorrect use will be a frustrating experience.

A Unscrew 10-24 NUT, remove and discard attach plate # BF3418 from bullet feeder assembly. HINT: if finger loosening is uncomfort-able, lightly snug with ⅜” wrenches.

B CInstall friction actuator and spring into carrier cover. Screw 10-24 hex nut on action rod (fits tightly). Finger tighten 10-24 hex nut. HINT: if finger tightening is uncomfortable, lightly snug with ⅜” wrenches.

D EInstall action rod into feeder link. Use end hole as shown.

Install Breech Lock bushing into position 3.

The LeeGuaranteelee reloading products are guaranteed not to wear out or break from normal use for two full years or they will be re paired or replaced at no charge if returned to the factory. Any Lee product of current manufacture, regardless of age or condition, will be recon di tioned to new, including a new guarantee, if re turned to the factory with payment equal to half the current retail price.

Install bullet seating die with lock ring on and feeder assembly into position 3.

6

ATTACH ATTACH PLATEPLATE

10-24 10-24 hex nuthex nut

Friction Friction ActuatorActuator

FEEDER FEEDER LINKLINK

VIDEO

WARNING: Handling live primers and spent primers may expose you to lead or other chemicals, which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov.

WARNING: This product may contain steel alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. For more information, go to www.P65Warnings.ca.gov. To prevent exposure, do not alter the product by welding, grinding, etc.

(1) Breech Lock bushing and (1) lock ring are required to utilize Automatic Bullet FeedProduct # 90600 and Part # SD4239

F Bullet feed completed installation.