SealerSales KF-210HC 8" Hand Impulse Sealer w/ Sliding

Cutter (10mm Seal Width)

Instruction Manual

IMPULSE SEALER( 100H, 200H, 300H, 400H, 520H )\ 200HC. 300HC, 400HC, 500HC '

INSTRUCTION MANUAL

Thanks for your purchase of our impusesealers. To obtain the benefit from ourproducts. Please read the followinginstruction before operation.

HANDLE

\

TIMER KNOB

WARNING !!To reduce the risk of shock, disconnectthe unit from the supply circuit beforeservicing the replacement of the heatingelement.

- 1 -

HEATING ADJUSTMENT LIST

{enrlt-trOlClfOR---'-

POLYETHYLENE POLYPROPYLENEOR HIGH-HEAT FILiI

UNDER 006m/m

2 UNDER 0.1m/m

3 UNDER 0.14m/m

4 UNDER 0.2mlm UNDER 0.03m/mq UNDER 0.044m/m

6 UNDER 0.06m/m7 UNDER OOBm/m

OPERATION. PUT THIS MACHINE ON A LEVEL AND DRY WORK TABLE.. PLEASE CHECK THE VOLTAGE OF POWER SOCKET, THEN INSERT

I THE POWER PLUG INTO SOCKET. TRY TO PRESS DOWN HANDLEKNOB AND TO EXAMINE THE PILOT LAMP IS LIGHTING OR NOT.

II . ACCORDING TO MATERIAL VARIETY AND THICKNESS OF POLY-BAG,REGULATED HEATING TIME DURATION AT APPROPRIATE DEGREE.

. PUT A POLY-BAG ON THE HEATING ELEMENT OF THIS MACHINE,THEN PRESS DOWN HANDLE KNOB AFTER 1.2 SECONDS, THEPERFECT SEAL APPEAR. (SLIDE THE KNIFE COVER FINISHEDcuTTlNG, 200HC. 300HC. 400HC)

. IF THE SEALING APPREARANCE IS BREAK OR DAMAGE PLEASEREGULATE TIMER KNOB, TOWARD THE 'S" SIDE AND TRY AGAINTILL THE PERFECT SEAL APPEAR.

.IF THE SEALING APPEARANCE IS NON-FULL.WELD, PLEASEREGULATE TIMER KNOB TOWARD THE "L' SIDE AND TRY AGAINTILL THE PERFECT SEAL APPEAR.

. IF THE POLY-BAG STICKS TO SEALING SILICON RUBBER. PLEASESHORTEN THE SEALING PRESS TIME.

-2-

CAUTIONO KEEP CLEAN, ESPECIALLY THE CLEAN OF HEATER. INSULATED CLOTH, UPPER CLOTH AND HEATING ELEMENT.. DON'T BE WET OR HUMIDITY FOR THE CAUSE OF

ELECTRIC OBSTACLE.. BEFORE OPERATION OR ON OPERATION, CHECK HEATER

INSULATED CLOTH AND UPPER CLOTH. IF THEY AREUNUSUAL, REPLACE IT AT ONCE, BECAUSE THE WORNHEATER INSULATED CLOTH AND UPPER CLOTH WILL MAKEELECTRIC SHORTWAY ALSO WILL DAMAGE TO HEATINGELEMENT,

. WHILE REPLACED HEATING ELEMENT MUST BE SAMESIZE AS ORIGINAL.

. WHILE SEALING APPEARANCE IS NOT ENOUGH EXCELLENTSHOULD REPLACE SEALING SILICON RUBBER.

. DON'T STRIKE POWERFULLY OTHERWISE THE BREAKDOWNWILL HAPPEN.

. WHEN USE EXCESSIVE. THE TEMPERATURE TOO HIGH,SUSPEND A LITTLE WHILE,

- 3 -

INSTRUCTION FOR REPLACING THE TELFLON CLOTHAND THE HEATER.

REMOVE THE TEFLON CLOTH FROM THE FIXED PLATE. REPLACE WITH A NEWTEFLON CLOTH, SECURE THE FIXED PLATE WITH SCREWS.

WHEN CHANGING THE HEATER, REMOVE THE TEFLON CLOTH AND UNSCREW THEHEATER. PLACE ONE END OF THE HEATER ON THE ELECTRODE AND SECURE THEOTHER END WITH SCBEWS. THEN SCREW ON THE TEFLON CLOTH.

ELECTRODE

TELFLON CLOTHSCREW

HEATER

FIXEDPLATE

SCREW

MALFUCTIONS

MALFUCTIONS REASONS SUGGESTIONS

POWER FAILUREOF THE HEATINGWIRE AND PILOT

. DISCONNE TED PLUG . CHANGE THE PLUG

. SHORT OF AC CORD . BEPAIR OR REPLACE

. AC CIRCUIT DISCONNE TED . REPAIR AC CIRCUIT

POWER FAILUREBUT THE PILOTLAMP IS STILL ON

. HEATER BROKEN . REPLACE THE HEATING WIRE

. DISCONNECTED ELECTRODESPRING

. REPLACE THE ELECTRODEWIRE OR CHECK VOLTAGE

PILOT LAMP STILLON AND THE TEFLONCLOTH OVERHEATS

. TTMER MALFUNCTION . CONTACT YOUR SUPPLIER

O PROLONGED HEATING TIME . DECREASE THE HEATING TIME

HEATING WIREBROKEN SUDDENLY

O TOO FREQUENT OPERATIONNEED APPROPRIATECOOLING PERIOD.

. KEEP AT LEAST I SECONDAFTER THE LED LAMP OFF,THEN PUSH THE HANDLE.DAILY OPERATION SHOULDNOT EXCEED 1,OOO TIMES

. FRACTURED GI-ASS TAPE O REPALCE THE GLASS TAPE

TO BE CONTINUED-5-

IMPERFECT l. FRACTURED TEFLON CLOTH l. REpLnCe THE TEFLON CLOTH

. KEEP AT LEAST 1 SECONDCOOLING TIME.l,'

I

il CONNECTION DIAGRAM

MICRO SWITCH

AC SOURCE

TRANSFORMER

- 6 -

TIMER SET

HEATING ELEMENT

F

1ooH, -2OoH, 3OOH' 4OoH' 52of l '

PARTS DIAGRAM

-7-

, 1 0 0 H , 2 0 0 H , 3 0 0 H , 4 0 0 H , 5 2 0 HITEM

I

PARTS NAME ITEM PARTS NAMEHANDLE KNOB ' I '

13 HEATER INSULATED CLOTH2

3

ARM 't4MICHOSWITCH BRACKET SPRTNG

HINGE BRACKET 15 POWER CORD4 COIL SPRING 16 HEAIING ELEMENT PIN

6

MICROSWITCH BRACKET '17MIUHO SWITCH

SEALING PLATED 18 TRANSFORMER (OUT.PI JN TFFII\ i | INASEALING SILICON RUBBER 1 9 I HANSFORMER

I UPPER CLOTH 20I I I \ ( ] tsLhMENT 21 TRANSFORMER SUPPORTOR---

RUBBER FOOT10 FIXED PLATE 22l 1 TIMER SET 2312 WIRE CONNECTOR

-8-

2o0HC. sooHc' 400HC

PARTS DIAGRAM

200Hc, 300Hc, 400HC, 500HCITEM PARTS NAME lTElr, PARTS NAME ITEM PARTS NAME

1 BODY 17-1 MICROSWITCH SPRING PUTE 35 TEFLON FIXED PI.ATE2 TIMER 1 8 MICROSWITCH ASSEMBTED SCHEW36 TEFION FIXED PI.ATE SCREW\' SCREW 1 9 MICROSWITCH FIXED SCBEW 37 SEAUNG BAR4 BOW SPBING 20 HINGE PIN 38 SEALING BAR FIXED BMCKET5 TRASFORMER 21 WIRECONNECTOR 39 SEALING BAR FIXED BRACKET SCREW6 TMNSFORMER BMCKET 22 EARIH WIRE 40 SEAUNG BAR RETURN SPRING7 SCBM 23 EARTH WIRE NUT WASHER 41 SEALING BAR RETURN SPRING SCREW

SPRING WASHER 24 BASE PI.ATE 42 SILICON RUBBER (SEALING PAD)B PI-ASTIC WASHER 25 EARTH WIRE SCREW 43 HANDLE KNOBo HINGE BRACKET 26 BUSHING 44 HANDLE KNOB WASHER1 0 SCREW POWER CORD A F BI.ADE HOLDER1 1 AFi/ 28 RUBBER FOOT 46 CUTTER BI.ADE12 ARM OPEMTING BMCKET 29 RUBBER FOOTSCRM 47 BLADE FIXED PLATE

I/ICROSWITCH ADJUSTING SCREW30 LOWER IEFLON (ADHESIVE) 48 BI-ADE FIXED SCREW. NUT1 4 ARM RETURN SPRING J I HEATING ELEMENT 49 HEATING ELEMENT COVERI A MICROSWITCH BMCKET 32 UPPER TEFLON 50 HEATING ELEI\,IENI COVER SCREWt o INSULATED PLqTE 33 TEFLON PI.ATE1 7 MICROSWITCH 34 TEFLON PTATE SCREW

_10_

SPARE PARS:

TEFLON GLOTHx2 PIECES