instrument panel yaris 2008
DESCRIPTION
Cuadro de instrumentos Toyota Yaris.Wiring diagrams for Yaris.TRANSCRIPT
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP1
I
UPPER INSTRUMENT PANEL (for Sedan)PRECAUTION1. PRECAUTION FOR VEHICLES WITH SRS AIRBAG
AND SEAT BELT PRETENSIONER(a) Some of these operations may affect the SRS
airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-1).
-
IPIP2 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
COMPONENTS
COMBINATION
METER ASSEMBLY
INSTRUMENT CLUSTER
FINISH PANEL
INSTRUMENT PANEL
FINISH PANEL END LH
INSTRUMENT PANEL
FINISH PANEL END RH
INSTRUMENT PANEL FINISH
PANEL LOWER CENTER
E116817E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP3
I
FRONT DOOR OPENING
TRIM WEATHERSTRIP LH
FRONT DOOR OPENING
TRIM WEATHERSTRIP RH
FRONT PILLAR
GARNISH LHFRONT PILLAR
GARNISH RH
GLOVE COMPARTMENT
DOOR ASSEMBLY
UPPER INSTRUMENT
PANEL SUB-ASSEMBLY
FRONT PILLAR
GARNISH LH
FRONT PILLAR
GARNISH RH
Non-reusable part
N*m (kgf*cm, ft*lbf) : Specified torque
20 (204, 15)
w/ Curtain Shield Airbag:
SPECIAL CLIP
SPECIAL CLIP
B132310E02
-
IPIP4 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
FRONT PASSENGER
AIRBAG ASSEMBLY
INSTRUMENT
PANEL CUSHION
NO. 1 HEATER TO
REGISTER DUCT
NO. 1 INSTRUMENT
PANEL CUSHION
NO. 1 INSTRUMENT PANEL
REGISTER ASSEMBLY
NO. 2 HEATER TO
REGISTER DUCT
NO. 2 INSTRUMENT
PANEL CUSHION
NO. 3 INSTRUMENT
PANEL CUSHION
NO. 1 INSTRUMENT PANEL
REGISTER ASSEMBLY
UPPER INSTRUMENT
PANEL
B132378E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP5
I
REMOVALHINT:Use the same procedure for both the RH and LH sides.
1. BOLTS, SCREWS AND NUTS TABLEHINT:All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL(a) Wait for at least 90 seconds after disconnecting the
cable to prevent the airbag from working.
3. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page ME-138)
4. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (See page ME-138)
5. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (See page ME-138)
6. REMOVE INSTRUMENT CLUSTER FINISH PANEL (See page ME-139)
7. REMOVE COMBINATION METER ASSEMBLY (See page ME-139)
8. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH(a) Separate the front door opening trim weatherstrip.
9. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH(a) Separate the front door opening trim weatherstrip.
10. REMOVE FRONT PILLAR GARNISH RH (See page IR-18)
11. REMOVE FRONT PILLAR GARNISH LH (See page IR-19)
Code Shape
Shape ShapeCode Code
mm(in.) (L=Length)
=5
(0.20)
L=14
(0.55)
=5
(0.20)
L=14
(0.55)
=8
(0.31)
L=15
(0.59)
B118994E01
-
IPIP6 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
12. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY(a) Disengage the claw and separate the 2 glove
compartment door stoppers from the glove compartment door.
(b) Slightly flex the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
(c) Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door.NOTICE:Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.
13. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY(a) Slide the slider and disconnect the passenger
airbag connector.(b) Disconnect the clamp.
Stopper
B132319E01
HingeB132320E01
Slider
B132322E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP7
I
(c) Remove the 2 bolts and 2 screws.
B132323E01
-
IPIP8 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
(d) Disengage the 7 clips by lifting the rear side of the instrument panel up.
(e) While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws from the front side of the instrument panel and remove the instrument panel.
14. REMOVE NO. 2 HEATER TO REGISTER DUCT(a) Remove the 2 screws and remove the register
duct.
B132324
B132325
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP9
I
15. REMOVE NO. 1 HEATER TO REGISTER DUCT(a) Remove the 2 screws and remove the register
duct.
16. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY(a) Disengage the 3 claws and remove the register.
HINT:Use the same procedure for both sides.
17. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY (See page RS-328)
18. REMOVE INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
upper instrument panel.
19. REMOVE NO. 1 INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
upper instrument panel.
20. REMOVE NO. 2 INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
upper instrument panel.
B132326
B132327
B132331
B132328
B132329
-
IPIP10 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
21. REMOVE NO. 3 INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
upper instrument panel.
INSTALLATION1. INSTALL NO. 3 INSTRUMENT PANEL CUSHION
(a) Install the instrument panel cushion onto the upper instrument panel.
2. INSTALL NO. 2 INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the upper
instrument panel.
3. INSTALL NO. 1 INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the upper
instrument panel.
4. INSTALL INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the upper
instrument panel.
5. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY (See page RS-329)
B132330
B132330
B132329
B132328
B132332
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP11
I
6. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY(a) Engage the 3 claws and install the register.
HINT:Use the same procedure for both sides.
7. INSTALL NO. 1 HEATER TO REGISTER DUCT(a) Install the register duct with the 2 screws.
8. INSTALL NO. 2 HEATER TO REGISTER DUCT(a) Install the register duct with the 2 screws.
9. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY(a) Using a nipper, cut off both ends of the runner
portion shown in the illustration (When installing a new one).
(b) Engage the 5 claws at the front side of the instrument panel.
B132327
B132326
B132325
Cut Off
Runner Portion
B130309E01
-
IPIP12 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
(c) Engage the 7 clips at the rear side of the instrument panel.
B132324
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan) IP13
I
(d) Install the upper instrument panel with the 2 bolts and the 2 screws.
Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) for bolt
(e) Connect the passenger airbag connector and clamp.
10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY(a) Engage the claws of the hinge portions by pushing
the glove compartment door in the horizontal direction to install the glove compartment door assembly.NOTICE:Engage the claw by pushing it in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.
B132323E01
B132386
HingeB132321E01
-
IPIP14 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Sedan)
(b) Slightly flex the upper portion of the glove compartment door assembly to engage the stopper.
(c) Install the 2 glove compartment door stoppers onto the glove compartment door.
11. INSTALL FRONT PILLAR GARNISH RH (See page IR-29)
12. INSTALL FRONT PILLAR GARNISH LH (See page IR-30)
13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH(a) Install the front door opening trim weatherstrip.
14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH(a) Install the front door opening trim weatherstrip.
15. INSTALL COMBINATION METER ASSEMBLY (See page ME-140)
16. INSTALL INSTRUMENT CLUSTER FINISH PANEL (See page ME-140)
17. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (See page ME-141)
18. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (See page ME-141)
19. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page ME-142)
20. CONNECT CABLE TO NEGATIVE BATTERY TERMINALTorque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
21. CHECK SRS WARNING LIGHT(See page RS-31)
Stopper
B132319E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP15
I
UPPER INSTRUMENT PANEL (for Hatchback)PRECAUTION1. PRECAUTION FOR VEHICLE WITH SRS AIRBAG
AND SEAT BELT PRETENSIONER(a) Some of these operations may affect the SRS
airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page RS-31).
-
IPIP16 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
COMPONENTS
COMBINATION METER ASSEMBLY
INSTRUMENT CLUSTER FINISH PANEL
INSTRUMENT PANEL
FINISH PANEL END LH
INSTRUMENT PANEL
FINISH PANEL END RH
E107796E02
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP17
I
FRONT DOOR OPENING TRIM WEATHERSTRIP LH
FRONT DOOR OPENING
TRIM WEATHERSTRIP RH
FRONT PILLAR
GARNISH LH
FRONT PILLAR GARNISH RH
GLOVE COMPARTMENT DOOR ASSEMBLY
CLIPCLIP
N*m (kgf*cm, ft.*lbf) : Specified torque
w/ Curtain Shield Airbag:
20 (204, 15)
Non-reusable part
CLIP
FRONT PILLAR GARNISH RH
FRONT PILLAR GARNISH LH
CLIP
UPPER INSTRUMENT
PANEL SUB-ASSEMBLY
NO. 1 SWITCH HOLE BASE
B108209E01
-
IPIP18 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
INSTRUMENT PANEL CUP
HOLDER SPRING
INSTRUMENT PANEL CUSHION
UPPER
INSTRUMENT
PANEL
INSTRUMENT PANEL
CUP HOLDER SPRING
FRONT PASSENGER
AIRBAG ASSEMBLY
NO. 1 HEATER TO
REGISTER DUCT
NO. 1 INSTRUMENT PANEL
BOX DOOR SUB-ASSEMBLY
NO. 1 INSTRUMENT
PANEL CUSHION
NO. 1 INSTRUMENT
PANEL REGISTER
ASSEMBLY
NO. 2 HEATER TO REGISTER DUCT
NO. 2 INSTRUMENT PANEL
BOX DOOR SUB-ASSEMBLY
NO. 2 INSTRUMENT PANEL CUSHION
NO. 3 INSTRUMENT
PANEL CUSHION
NO. 1 INSTRUMENT PANEL
REGISTER ASSEMBLY
NO. 1 INSTRUMENT
PANEL CUP HOLDER
NO. 2 INSTRUMENT
PANEL CUP HOLDER
B105349E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP19
I
REMOVALHINT:Use the same procedure for both the RH and LH sides.
1. BOLTS, SCREWS AND NUTS TABLEHINT:All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL(a) Wait for at least 90 seconds after disconnecting the
cable to prevent the airbag from working.
3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (See page ME-145)
4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (See page ME-145)
5. REMOVE INSTRUMENT CLUSTER FINISH PANEL (See page ME-145)
6. REMOVE COMBINATION METER ASSEMBLY (See page ME-146)
7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page IR-50)
8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (See page IR-50)
9. REMOVE FRONT PILLAR GARNISH RH (See page IR-58)
10. REMOVE FRONT PILLAR GARNISH LH (See page IR-59)
Code Shape
Shape ShapeCode Code
mm(in.) (L=Length)
=5
(0.20)
L=14
(0.55)
=5
(0.20)
L=14
(0.55)
=8
(0.31)
L=15
(0.59)
B118994E01
-
IPIP20 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
11. REMOVE NO. 1 SWITCH HOLE BASE(a) Disengage the 2 clips and 2 claws and remove the
switch hole base.
12. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY(a) Slightly deform the upper part of the glove
compartment door assembly to release the 2 stoppers and open the glove compartment door assembly until it becomes horizontal.
(b) Pull the glove compartment door assembly out horizontally to disengage the hinge portion and remove the glove compartment door assembly.NOTICE:Pull the glove compartment door out horizontally, otherwise, installation failure caused by excessive play around the hinge portion will result.
B105353
B108202
B105351
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP21
I
13. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY(a) Slide the slider and disconnect the passenger
airbag connector.(b) Disconnect the clamp.(c) Remove the 2 bolts and 4 screws.
(d) Disconnect the connectors.(e) Disengage the claw and 3 clips while lifting the rear
instrument panel up.
Slider
B108181E02
B105354E01
-
IPIP22 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
(f) While lifting the instrument panel, slide it toward the rear of the vehicle. Disengage the 5 claws of the front side of the instrument panel and remove the instrument panel.
B105355E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP23
I
14. REMOVE NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY(a) Remove the 2 screws.(b) Pull the instrument panel box door toward the rear
of the vehicle, disengage the 2 claws and 2 clips and remove the instrument panel box door.
15. REMOVE NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY(a) Remove the 2 screws.(b) Pull the instrument panel box door toward the rear
of the vehicle, disengage the 2 claws and 2 clips and remove the instrument panel box door.
16. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING(a) Remove screw and remove the cup holder
spring.
17. REMOVE NO. 1 INSTRUMENT PANEL CUP HOLDER(a) Slightly deform portion A of the cup holder by
pressing it and release the stopper.
B105356
B105358
B105360
A
A
B108174E01
-
IPIP24 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
(b) Using a screwdriver with its tip wrapped in protective tape, prize the hinge portion of the cup holder from side to side while being careful not to apply excessive load to the axis of the instrument panel upper, and remove the cup holder.
18. REMOVE NO. 2 INSTRUMENT PANEL CUP HOLDERHINT:Use the same procedure as for the RH side.
19. REMOVE NO. 2 HEATER TO REGISTER DUCT(a) Remove the 2 screws and remove the register
duct.
20. REMOVE NO. 1 HEATER TO REGISTER DUCT(a) Remove the 2 screws and remove the register
duct.
Protective
Tape
B108173E01
B108177
B108176
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP25
I
21. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY(a) Disengage the 3 claws and remove the register.
HINT:Use the same procedure as for the opposite side.
22. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY (See page RS-340)
23. REMOVE INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
instrument panel upper.
24. REMOVE NO. 1 INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
instrument panel upper.
25. REMOVE NO. 2 INSTRUMENT PANEL CUSHION(a) Remove the instrument panel cushion from the
instrument panel upper.
B108178
B108179
B108203
B108204
-
IPIP26 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
26. REMOVE NO. 3 INSTRUMENT PANEL CUSHION(a) Remove the 2 instrument panel cushions from the
instrument panel upper.
INSTALLATION1. INSTALL NO. 3 INSTRUMENT PANEL CUSHION
(a) Install the 2 instrument panel cushions onto the instrument panel upper.
2. INSTALL NO. 2 INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the
instrument panel upper.
B108205
B108205
B108204
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP27
I
3. INSTALL NO. 1 INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the
instrument panel upper.
4. INSTALL INSTRUMENT PANEL CUSHION(a) Install the instrument panel cushion onto the
instrument panel upper.
5. INSTALL FRONT PASSENGER AIRBAG ASSEMBLY (See page RS-341)
6. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY(a) Engage the 3 claws and install the register.
HINT:Use the same procedure as for the opposite side.
7. INSTALL NO. 1 HEATER TO REGISTER DUCT(a) Install the register duct with the 2 screws.
B108203
B108180
B108178
B108176
-
IPIP28 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
8. INSTALL NO. 2 HEATER TO REGISTER DUCT(a) Install the register duct with the 2 screws.
9. INSTALL NO. 1 INSTRUMENT PANEL CUP HOLDER(a) Engage the hinge portion of the cup holder and
install the cup holder.
(b) Engage the stopper of the cup holder.
10. INSTALL NO. 2 INSTRUMENT PANEL CUP HOLDERHINT:Use the same procedure as for the RH side.
11. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING(a) Install the cup holder spring with screw .
B108177
B108175
B108174
B105360
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP29
I
12. INSTALL NO. 2 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY(a) Engage the 2 claws and 2 clips.(b) Install the box door with the 2 screws.
13. INSTALL NO. 1 INSTRUMENT PANEL BOX DOOR SUB-ASSEMBLY(a) Engage the 2 claws and 2 clips.(b) Install the box door with the 2 screws.
14. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY(a) Using a nipper, cut off both ends of the runner
portion shown in the illustration (When installing a new one).
(b) Engage the 5 claws at the upper side of the instrument panel.
B105359
B105357
Runner
Portion
Cut off
B108233E01
-
IPIP30 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
(c) Engage the claw and the 3 clips at the lower side of the instrument panel.
(d) Install the instrument panel upper with the 2 bolts and 4 screws.Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) for bolt
B105355E01
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP31
I
(e) Connect the connectors.
(f) Connect the passenger airbag connector and clamp.
B105354
B108182
-
IPIP32 INSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback)
15. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY(a) Engage the claw of the hinge portion in the
horizontal direction to install the glove compartment door assembly.NOTICE:Engage the claw in the horizontal direction, otherwise, installation failure caused by excessive play around the hinge portion will result.
(b) Slightly deform the upper portion of the glove compartment door assembly to engage the stopper.
16. INSTALL NO. 1 SWITCH HOLE BASE(a) Disengage the 2 clips and 2 claws and install the
switch hole base.
17. INSTALL FRONT PILLAR GARNISH RH (See page IR-71)
18. INSTALL FRONT PILLAR GARNISH LH (See page IR-72)
19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page IR-81)
20. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (See page IR-81)
21. INSTALL COMBINATION METER ASSEMBLY (See page ME-148)
22. INSTALL INSTRUMENT CLUSTER FINISH PANEL (See page ME-148)
23. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (See page ME-149)
B105352
B108202
B105353
-
PINSTRUMENT PANEL UPPER INSTRUMENT PANEL (for Hatchback) IP33
I
24. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (See page ME-149)
25. CONNECT CABLE TO NEGATIVE BATTERY TERMINALTorque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
26. CHECK SRS WARNING LIGHTRS-31
-
IPIP34 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)BODYINSTRUMENT PANELLOWER INSTRUMENT PANEL (for Sedan)COMPONENTS
INSTRUMENT PANEL
CUP HOLDER LH
INSTRUMENT PANEL
CUP HOLDER RH
INSTRUMENT PANEL CUP
HOLDER SPRING LH
INSTRUMENT PANEL CUP
HOLDER SPRING RH
B132397E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP35
I
COMBINATION
METER ASSEMBLY
INSTRUMENT CLUSTER
FINISH PANEL
INSTRUMENT PANEL
FINISH PANEL END LH
INSTRUMENT PANEL
FINISH PANEL END RH
INSTRUMENT PANEL FINISH
PANEL LOWER CENTER
E116817E01
-
IPIP36 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
FRONT DOOR OPENING
TRIM WEATHERSTRIP LH
FRONT DOOR OPENING
TRIM WEATHERSTRIP RH
FRONT PILLAR
GARNISH LHFRONT PILLAR
GARNISH RH
GLOVE COMPARTMENT
DOOR ASSEMBLY
UPPER INSTRUMENT
PANEL SUB-ASSEMBLY
FRONT PILLAR
GARNISH LH
FRONT PILLAR
GARNISH RH
Non-reusable part
N*m (kgf*cm, ft*lbf) : Specified torque
20 (204, 15)
w/ Curtain Shield Airbag:
SPECIAL CLIP
SPECIAL CLIP
B132310E02
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP37
I
AIR CONDITIONING
PANEL ASSEMBLY
AIR INLET DAMPER CONTROL
CABLE SUB-ASSEMBLY
AIR MIX DAMPER CONTROL
CABLE SUB-ASSEMBLY
DEFROSTER DAMPER
CONTROL CABLE
SUB-ASSEMBLY
INSTRUMENT CLUSTER FINISH
PANEL CENTER SUB-ASSEMBLY
RADIO RECEIVER ASSEMBLY
STEREO OPENING
COVER
RADIO RECEIVER
ASSEMBLY
w/o Radio Receiver:
for Integrated w/ Panel:
Except for Integrated w/ Panel:
Except for Integrated w/ Panel:
B132383E01
-
IPIP38 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
CONSOLE BOX CARPET
CONSOLE UPPER REAR
PANEL SUB-ASSEMBLY
REAR CONSOLE BOX ASSEMBLY
SHIFT LEVER KNOB
SUB-ASSEMBLY
UPPER CONSOLE PANEL
SUB-ASSEMBLY
for Manual Transaxle:
UPPER CONSOLE PANEL SUB-ASSEMBLY
B132313E02
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP39
I
COWL SIDE
TRIM BOARD LH
COWL SIDE
TRIM BOARD RH
FRONT DOOR
SCUFF PLATE LH
FRONT DOOR
SCUFF PLATE RH
HOOD LOCK CONTROL
LEVER SUB-ASSEMBLY
INSTRUMENT
PAD LOWER LH
INSTRUMENT
PAD LOWER RH
INSTRUMENT
PANEL BOX
INSTRUMENT PANEL LOWER
FINISH PANEL SUB-ASSEMBLY
INSTRUMENT PANEL UNDER
COVER SUB-ASSEMBLY LH
INSTRUMENT PANEL UNDER
COVER SUB-ASSEMBLY RH
LOWER INSTRUMENT
PANEL SUB-ASSEMBLY
B132379E01
-
IPIP40 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
GLOVE COMPARTMENT
DOOR STOPPER
SUB-ASSEMBLY
INSTRUMENT CLUSTER
FINISH PANEL SEAL
INSTRUMENT PANEL
NO. 1 SAFETY PAD
INSTRUMENT PANEL
NO. 2 SAFETY PAD
LIGHT CONTROL
RHEOSTAT
OUTER MIRROR
SWITCH ASSEMBLY
STEREO JACK
ADAPTER ASSEMBLY
LOWER INSTRUMENT
PANEL
INSTRUMENT PANEL CUP
HOLDER SUB-ASSEMBLY LH
INSTRUMENT PANEL CUP
HOLDER SUB-ASSEMBLY RH
B132380E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP41
I
REMOVALHINT:Use the same procedure for both the RH and LH sides.
1. BOLTS, SCREWS AND NUTS TABLEHINT:All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINALWait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.
Code Code CodeShape
Shape Shape
=5
(0.20)
L=14
(0.55)
=6
(0.24)
L=20
(0.79)
=6
(0.24)
L=16
(0.63)
=6
(0.24)
L=16
(0.63)
=5
(0.20)
L=16
(0.63)
=5
(0.20)
L=14
(0.55)
=5
(0.20)
L=16
(0.63)
=8
(0.31)
L=15
(0.59)
mm(in.) (L=Length)
=5
(0.20)
L=16
(0.63)
B132394E01
-
IPIP42 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
3. REMOVE INSTRUMENT PANEL CUP HOLDER RH(a) Open the instrument panel cup holder.(b) Flex both sides of the instrument panel cup holder
and disengage the 2 stoppers.
(c) Disengage the spring.
(d) Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.
4. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING RH(a) Remove the spring.
5. REMOVE INSTRUMENT PANEL CUP HOLDER LH(a) Open the instrument panel cup holder.(b) Flex both sides of the instrument panel cup holder
and disengage the 2 stoppers.
Stopper
B132398E01
B132399
Hing
B132400E01
B132402
Stopper
B132403E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP43
I
(c) Remove the instrument panel cup holder by moving it toward either the inside or the outside of the vehicle and disengaging the 2 hinges one at a time.
6. REMOVE INSTRUMENT PANEL CUP HOLDER SPRING LH(a) Remove the spring.
7. REMOVE INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page ME-138)
8. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (See page ME-138)
9. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (See page ME-138)
10. REMOVE INSTRUMENT CLUSTER FINISH PANEL (See page ME-139)
11. REMOVE COMBINATION METER ASSEMBLY (See page ME-139)
12. REMOVE INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY(a) Disengage the 2 claws and 4 clips and remove the
instrument cluster panel center.
13. REMOVE STEREO OPENING COVER (w/o Radio Receiver)(a) Remove the 4 screws and remove the stereo
opening cover.
14. REMOVE RADIO RECEIVER ASSEMBLY (See page AV-38)
15. REMOVE AIR CONDITIONING PANEL ASSEMBLY (See page AC-239)
16. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-240)
17. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-240)
18. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-240)
Hing
B132404E01
B132406
B132395
B132396
-
IPIP44 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
19. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page IP-5)
20. SEPARATE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (See page IP-5)
21. REMOVE FRONT PILLAR GARNISH RH (See page IR-18)
22. REMOVE FRONT PILLAR GARNISH LH (See page IR-19)
23. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (See page IP-6)
24. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY (See page IP-6)
25. REMOVE FRONT DOOR SCUFF PLATE RH (See page IR-14)
26. REMOVE FRONT DOOR SCUFF PLATE LH (See page IR-14)
27. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH (See page IR-14)
28. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH (See page IR-14)
29. REMOVE COWL SIDE TRIM BOARD RH (See page IR-15)
30. REMOVE COWL SIDE TRIM BOARD LH (See page IR-15)
31. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle) (See page IP-84)
32. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (See page IP-84)
33. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY (See page IP-84)
34. REMOVE CONSOLE BOX CARPET (See page IP-85)35. REMOVE REAR CONSOLE BOX ASSEMBLY (See
page IP-85)36. REMOVE INSTRUMENT PAD LOWER LH
(a) Remove screw .(b) Disengage the claw and 3 clips and remove the
instrument panel pad lower.
B132339
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP45
I
37. REMOVE INSTRUMENT PAD LOWER RH(a) Remove screw .(b) Disengage the claw and 3 clips and remove the
instrument panel pad lower.
38. REMOVE INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY(a) Disengage the 7 claws and open the instrument
panel lower finish panel.
(b) Remove the 2 screws and remove the instrument panel lower finish panel.
39. REMOVE INSTRUMENT PANEL BOX(a) Open the instrument panel box.(b) Pull the instrument panel box out horizontally with
the instrument panel open and disengage the 2 hinges.
B132340
B132381
B132382
Hinge
B132334E01
-
IPIP46 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
(c) Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.
40. DISCONNECT ANTENNA CORD SUB-ASSEMBLY(a) Disconnect the 5 antenna cord clamps.
41. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY(a) Disengage the 3 claws and separate the hood lock
control lever.
42. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY(a) Disengage the 2 claws and disconnect the DLC3
connector.(b) Disconnect the clamps and connectors.
Stopper
Cutout
B132335E01
B132369
B132338
B108192
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP47
I
(c) Remove the 6 bolts, 2 bolts, screw and screw and remove the lower instrument panel.
43. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY LH(a) Remove the 3 screws and the instrument panel
cup holder.
44. REMOVE INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY RH(a) Remove the 3 screws and the instrument panel
box.
B132342E01
B132343
B132344
-
IPIP48 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
45. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY(a) Disengage the claw and remove the glove
compartment door stopper.
46. REMOVE OUTER MIRROR SWITCH ASSEMBLY(a) Disengage the 2 claws and remove the outer mirror
switch.
47. REMOVE LIGHT CONTROL RHEOSTAT(a) Disengage the 2 claws and remove the light control
rheostat.
B132392
B132357
B132358
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP49
I
48. REMOVE STEREO JACK ADAPTER ASSEMBLY(a) Disengage the 2 claws and remove the stereo jack
adapter.
49. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL(a) Disengage the 5 claws and remove the panel seal.
50. REMOVE INSTRUMENT PANEL NO. 1 SAFETY PAD(a) Remove the safety pad.
51. REMOVE INSTRUMENT PANEL NO. 2 SAFETY PAD(a) Remove the safety pad.
B132360
B132393
B132362
B132361
-
IPIP50 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
INSTALLATION1. INSTALL INSTRUMENT PANEL NO. 1 SAFETY PAD
(a) Apply butyl tape to install the instrument panel safety pad No. 1 onto the instrument panel lower (When installing a new one).Adhesive:
Part No. 08850-00065, Butyl Tape Set or the equivalent
2. INSTALL INSTRUMENT PANEL NO. 2 SAFETY PAD(a) Apply butyl tape to install the instrument panel
safety pad No. 2 onto the instrument panel lower (When installing a new one).Adhesive:
Part No. 08850-00065, Butyl Tape Set or the equivalent
3. INSTALL INSTRUMENT CLUSTER FINISH PANEL SEAL(a) Engage the 5 claws and install the panel seal.
4. INSTALL STEREO JACK ADAPTER ASSEMBLY(a) Engage the 2 claws and install the stereo jack
adapter.
B132362
B132361
B132393
B132360
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP51
I
5. INSTALL LIGHT CONTROL RHEOSTAT(a) Engage the 2 claws and install the light control
rheostat.
6. INSTALL OUTER MIRROR SWITCH ASSEMBLY(a) Engage the 2 claws and install the outer mirror
switch.
7. INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY(a) Engage the claw and install the glove compartment
door stopper.
8. INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY LH(a) Install the instrument panel cup holder with the 3
screws.
B132358
B132357
B132392
B132343
-
IPIP52 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
9. INSTALL INSTRUMENT PANEL CUP HOLDER SUB-ASSEMBLY RH(a) Install the instrument panel cup holder with the 3
screws.
10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY(a) Using a nipper, cut off both ends of the runner
portion shown in the illustration (When installing a new one).
(b) Install the lower instrument panel with the 6 bolts, 2 bolts, screw and screw .NOTICE:Do not excessively tighten the bolts, as this may damage the area not being tightened.
(c) Connect the clamps and connectors.
B132344
Runner
Portion
Cut OffB132391E01
B132342E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP53
I
(d) Engage the 2 claws and connect the DLC3 connector.
11. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY(a) Engage the 3 claws to connect the control lever.
12. CONNECT ANTENNA CORD SUB-ASSEMBLY(a) Connect the 5 antenna cord clamps.
13. INSTALL INSTRUMENT PANEL BOX(a) Insert the stopper of the instrument panel box from
the cutout of the instrument panel lower.
B108192
B132338
B132369
Stopper
Cutout
B132335E01
-
IPIP54 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
(b) Engage the 2 hinges with the instrument panel open.
(c) Close the instrument panel box.
14. INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY(a) Install the 2 screws.
(b) Engage the 7 claws and install the instrument panel lower finish panel.
15. INSTALL INSTRUMENT PAD LOWER RH(a) Engage the claw and 3 clips and install the
instrument pad lower.(b) Install screw .
Hinge
B132337E01
B132382
B132381
B132340
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP55
I
16. INSTALL INSTRUMENT PAD LOWER LH(a) Engage the claw and 3 clips and install the
instrument pad lower.(b) Install screw .
17. INSTALL REAR CONSOLE BOX ASSEMBLY (See page IP-88)
18. INSTALL CONSOLE BOX CARPET (See page IP-88)19. INSTALL CONSOLE UPPER REAR PANEL SUB-
ASSEMBLY (See page IP-89)20. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
(See page IP-89)21. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for
Manual Transaxle) (See page IP-89)22. INSTALL COWL SIDE TRIM BOARD RH (See page IR-
34)23. INSTALL COWL SIDE TRIM BOARD LH (See page IR-
34)24. INSTALL INSTRUMENT PANEL UNDER COVER SUB-
ASSEMBLY RH (See page IR-35)25. INSTALL INSTRUMENT PANEL UNDER COVER SUB-
ASSEMBLY LH (See page IR-34)26. INSTALL FRONT DOOR SCUFF PLATE RH (See page
IR-35)27. INSTALL FRONT DOOR SCUFF PLATE LH (See page
IR-35)28. INSTALL UPPER INSTRUMENT PANEL SUB-
ASSEMBLY (See page IP-11)29. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
(See page IP-13)30. INSTALL FRONT PILLAR GARNISH RH (See page IR-
29)31. INSTALL FRONT PILLAR GARNISH LH (See page IR-
30)32. INSTALL FRONT DOOR OPENING TRIM
WEATHERSTRIP RH (See page IP-14)33. INSTALL FRONT DOOR OPENING TRIM
WEATHERSTRIP LH (See page IP-14)34. CONNECT AIR INLET DAMPER CONTROL CABLE
SUB-ASSEMBLY (See page AC-246)35. CONNECT DEFROSTER DAMPER CONTROL CABLE
SUB-ASSEMBLY (See page AC-246)36. CONNECT AIR MIX DAMPER CONTROL CABLE
SUB-ASSEMBLY (See page AC-246)37. INSTALL AIR CONDITIONING PANEL ASSEMBLY
B132339(See page AC-246)
-
IPIP56 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
38. INSTALL STEREO OPENING COVER (w/o Radio Receiver)(a) Install the stereo opening cover with the 4 screws.
39. INSTALL RADIO RECEIVER ASSEMBLY (See page AV-40)
40. INSTALL INSTRUMENT CLUSTER FINISH PANEL CENTER SUB-ASSEMBLY(a) Engage the 2 claws and 4 clips and install the
instrument cluster finish panel center.
41. INSTALL COMBINATION METER ASSEMBLY (See page ME-140)
42. INSTALL INSTRUMENT CLUSTER FINISH PANEL (See page ME-140)
43. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (See page ME-141)
44. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (See page ME-141)
45. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page ME-142)
46. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING RH(a) Install the spring.
47. INSTALL INSTRUMENT PANEL CUP HOLDER RH(a) Install the 2 hinges of the cup holder one at a time.
B132396
B132395
B132402
Hing
B132401E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan) IP57
I
(b) Engage the spring with the instrument panel cup holder.
(c) Flex both sides of the cup holder and engage the 2 stoppers.
(d) Close the instrument panel cup holder.
48. INSTALL INSTRUMENT PANEL CUP HOLDER SPRING LH(a) Install the spring.
49. INSTALL INSTRUMENT PANEL CUP HOLDER LH(a) Install the 2 hinges of the cup holder one at a time.
HINT:Make sure that the spring is set in the position shown in the illustration.
B132399
Stopper
B132398E01
B132406
Spring
Stopper
Hing
B132405E01
-
IPIP58 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Sedan)
(b) Flex both sides of the cup holder and engage the 2 stoppers.
(c) Close the instrument panel cup holder.
50. CONNECT CABLE TO NEGATIVE BATTERY TERMINALTorque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
51. CHECK SRS WARNING LIGHT(See page RS-31)
Stopper
B132403E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP59
I
BODYINSTRUMENT PANELLOWER INSTRUMENT PANEL (for Hatchback)COMPONENTS
AIR CONDITIONER
PANEL SUB-ASSEMBLY
AIR INLET DAMPER
CONTROL CABLE
SUB-ASSEMBLY
COMBINATION METER ASSEMBLY
DEFROSTER DAMPER
CONTROL CABLE
SUB-ASSEMBLY
INSTRUMENT CLUSTER FINISH PANEL
INSTRUMENT CLUSTER
FINISH PANEL SUB-ASSEMBLY
CENTER
INSTRUMENT PANEL
FINISH PANEL END LH
INSTRUMENT PANEL
FINISH PANEL END RH
AIR MIX DAMPER CONTROL
CABLE SUB-ASSEMBLY
B108235E01
-
IPIP60 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
RADIO TUNER OPENING COVER
w/o Radio Receiver:
w/o CD Player:
w/ CD Player:
RADIO RECEIVER ASSEMBLY
RADIO RECEIVER ASSEMBLY
I101560E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP61
I
FRONT DOOR OPENING TRIM WEATHERSTRIP LH
FRONT DOOR OPENING
TRIM WEATHERSTRIP RH
FRONT PILLAR
GARNISH LH
FRONT PILLAR GARNISH RH
GLOVE COMPARTMENT DOOR ASSEMBLY
CLIPCLIP
N*m (kgf*cm, ft.*lbf) : Specified torque
w/ Curtain Shield Airbag:
20 (204, 15)
Non-reusable part
CLIP
FRONT PILLAR GARNISH RH
FRONT PILLAR GARNISH LH
CLIP
UPPER INSTRUMENT
PANEL SUB-ASSEMBLY
NO. 1 SWITCH HOLE BASE
B108209E01
-
IPIP62 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
CONSOLE BOX ASSEMBLY REAR
CONSOLE BOX CARPET
CONSOLE BOX REAR COVER
SHIFT LEVER KNOB
SUB-ASSEMBLY
SHIFTING HOLE COVER
SUB-ASSEMBLY
for Manual Transaxle:
B108229E02
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP63
I
COWL SIDE TRIM BOARD LH
COWL SIDE TRIM BOARD RH
FRONT DOOR
SCUFF PLATE LH
FRONT DOOR
SCUFF PLATE RH
INSTRUMENT PANEL FINISH PANEL
SUB-ASSEMBLY LOWER
INSTRUMENT PANEL UNDER
COVER SUB-ASSEMBLY LH
INSTRUMENT PANEL UNDER
COVER SUB-ASSEMBLY RH
B108230E01
-
IPIP64 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
NO. 6 HEATER TO REGISTER
DUCT ASSEMBLY
HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
INSTRUMENT PANEL BOX
LOWER INSTRUMENT
PANEL SUB-ASSEMBLY
B108207E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP65
I
FRONT PANEL SEAL
POWER OUTLET
SOCKET ASSEMBLY
POWER OUTLET
SOCKET COVER
INSTRUMENT PANEL BOX SPRING
INSTRUMENT PAD LOWER
OUTER MIRROR SWITCH ASSEMBLY
INSTRUMENT CLUSTER
FINISH PANEL SEAL
LOWER INSTRUMENT
PANEL SUB-ASSEMBLY
NO. 1 INSTRUMENT PANEL BOX
NO. 2 INSTRUMENT PANEL BOX
LIGHT CONTROL
RHEOSTAT
B108198E01
-
IPIP66 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
REMOVALHINT:Use the same procedure for both the RH and LH sides.
1. BOLTS, SCREWS AND NUTS TABLEHINT:All bolts, screws and nuts relevant to installing and removing the instrument panel are shown, along with their alphabetic codes, in the table below.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINALWait for at least 90 seconds after disconnecting the cable to prevent the airbag from working.
3. REMOVE INSTRUMENT PANEL FINISH PANEL END LH (See page ME-145)
4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH (See page ME-145)
5. REMOVE INSTRUMENT CLUSTER FINISH PANEL (See page ME-145)
Code Code CodeShape
Shape Shape
=5
(0.20)
L=14
(0.55)
=6
(0.24)
L=20
(0.79)
=6
(0.24)
L=16
(0.63)
=6
(0.24)
L=16
(0.63)
=5
(0.20)
L=16
(0.63)
=5
(0.20)
L=14
(0.55)
=5
(0.20)
L=16
(0.63)
=8
(0.31)
L=15
(0.59)
mm(in.) (L=Length)
B118995E01
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP67
I
6. REMOVE COMBINATION METER ASSEMBLY (See page ME-146)
7. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (See page AC-250)
8. REMOVE RADIO TUNER OPENING COVER (w/o Radio Receiver) (See page AC-125)
9. REMOVE RADIO RECEIVER ASSEMBLY (See page AV-44)
10. REMOVE AIR CONDITIONER PANEL SUB-ASSEMBLY (See page AC-250)
11. DISCONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-251)
12. DISCONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-251)
13. DISCONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-251)
14. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page IR-50)
15. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH (See page IR-50)
16. REMOVE FRONT PILLAR GARNISH RH (See page IR-58)
17. REMOVE FRONT PILLAR GARNISH LH (See page IR-59)
18. REMOVE NO. 1 SWITCH HOLE BASE (See page IP-20)
19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (See page IP-20)
20. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY (See page IP-21)
21. REMOVE FRONT DOOR SCUFF PLATE RH (See page IR-49)
22. REMOVE FRONT DOOR SCUFF PLATE LH (See page IR-49)
23. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH (See page IR-50)
24. REMOVE INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH (See page IR-50)
25. REMOVE COWL SIDE TRIM BOARD RH (See page IR-50)
26. REMOVE COWL SIDE TRIM BOARD LH (See page IR-50)
-
IPIP68 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
27. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)(a) Remove the shift lever knob.
28. REMOVE SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)(a) Disengage the 6 claws and remove the shifting hole
cover.
29. REMOVE CONSOLE BOX REAR COVER(a) Disengage the 8 claws and remove the console box
rear cover.
30. REMOVE CONSOLE BOX CARPET(a) Remove the console box carpet.
B118988
B118990
B118991
B118992
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP69
I
31. REMOVE CONSOLE BOX ASSEMBLY REAR(a) Remove bolt .(b) Disengage the 2 clips and remove the console box
rear.
32. REMOVE INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER(a) Disengage the 7 claws and open the instrument
panel finish panel lower.
(b) Remove the 2 screws and the instrument panel finish panel lower.
B118993
B108222
B108228
-
IPIP70 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
33. REMOVE INSTRUMENT PANEL BOX(a) Open the instrument panel box.(b) Pull the hinge side of the instrument panel box out
horizontally with the instrument panel open and disengage the 2 hinges.
(c) Remove the stopper of the instrument panel box from the cutout of the instrument panel lower and remove the instrument panel box.
34. REMOVE NO. 6 HEATER TO REGISTER DUCT ASSEMBLY(a) Disengage the 4 claws and remove the heater to
register duct.
35. DISCONNECT ANTENNA CORD SUB-ASSEMBLY(a) Disconnect the 2 antenna cord clamps.
Stopper
Cutout
Hinge
B108188E01
B108190
B108200
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP71
I
36. SEPARATE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY(a) Disengage the 3 claws and separate the hood lock
control lever.
37. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY(a) Disengage the 2 claws and disconnect the DLC3
connector.(b) Disconnect the clamps and connectors.(c) Remove the 5 bolts, 2 bolts, screw
and screw and remove the lower instrument panel.
B108191
B108192
B108193E01
-
IPIP72 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
38. REMOVE POWER OUTLET SOCKET ASSEMBLY (See page OT-9)
39. REMOVE POWER OUTLET SOCKET COVER (See page OT-10)
40. REMOVE OUTER MIRROR SWITCH ASSEMBLY(a) Disengage the 2 claws and remove the outer mirror
switch.
41. REMOVE LIGHT CONTROL RHEOSTAT(a) Disengage the 2 claws and remove the light control
rheostat.
42. REMOVE FRONT PANEL SEAL(a) Remove the front panel seal.
B108225
B108227
B108221
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP73
I
43. REMOVE INSTRUMENT PANEL BOX SPRING(a) Remove screw and the instrument panel box
spring.
44. REMOVE NO. 1 INSTRUMENT PANEL BOX(a) Remove the 2 screws and the instrument panel
box.
45. REMOVE NO. 2 INSTRUMENT PANEL BOX(a) Remove the 2 screws and the instrument panel
box.
46. REMOVE INSTRUMENT CLUSTER FINISH PANEL SEAL(a) Disengage the 5 claws and remove the panel seal.
INSTALLATION1. INSTALL INSTRUMENT CLUSTER FINISH PANEL
SEAL(a) Engage the 5 claws and install the panel seal.
B108194
B108196
B108195
B108197
B108197
-
IPIP74 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
2. INSTALL NO. 2 INSTRUMENT PANEL BOX(a) Install the instrument panel box with the 2
screws.
3. INSTALL NO. 1 INSTRUMENT PANEL BOX(a) Install the instrument panel box with the 2
screws.
4. INSTALL INSTRUMENT PANEL BOX SPRING(a) Install the instrument panel box spring with screw
.
5. INSTALL FRONT PANEL SEAL(a) Install the front panel seal.
B108195
B108196
B108194
B108221
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP75
I
6. INSTALL LIGHT CONTROL RHEOSTAT(a) Engage the 2 claws and install the light control
rheostat.
7. INSTALL OUTER MIRROR SWITCH ASSEMBLY(a) Engage the 2 claws and install the outer mirror
switch.
8. INSTALL POWER OUTLET SOCKET COVER (See page OT-10)
9. INSTALL POWER OUTLET SOCKET ASSEMBLY (See page OT-10)
10. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY(a) Using a nipper, cut off both ends of the runner
portion shown in the illustration (When installing a new one).
(b) Apply butyl tape to install a new instrument panel pad lower onto the instrument panel lower (When installing a new one).Adhesive:
Part No. 08850-00065, Butyl Tape Set or the equivalent
(c) Install the lower instrument panel with the 5 bolts, 2 bolts, screw and screw .NOTICE:Do not excessively tighten the bolts, otherwise, it may damage the area not being tightened.
B108227
B108225
Runner
Portion
Cut off
B108232E01
-
IPIP76 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
(d) Connect the clamps and connectors.
(e) Engage the 2 claws to connect the DLC3 connector.
B108193E01
B108192
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP77
I
11. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY(a) Engage the 3 claws to connect the control lever.
12. CONNECT ANTENNA CORD SUB-ASSEMBLY(a) Connect the 2 antenna cord clamps.
13. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY(a) Engage the 4 claws and install the heater to register
duct.
B108191
B108200
B108190
-
IPIP78 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
14. INSTALL INSTRUMENT PANEL BOX(a) Insert the stopper of the instrument panel box from
the cutout of the instrument panel lower.(b) Engage the hinges with the instrument panel open.(c) Close the instrument panel box.
15. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER(a) Install the 2 screws.
(b) Engage the 7 claws and install the instrument panel finish panel lower.
Stopper
Cutout
Hinge
B108189E01
B108228
B108223
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP79
I
16. INSTALL CONSOLE BOX ASSEMBLY REAR(a) Engage the 2 clips and install the console box rear.(b) Install bolt .
17. INSTALL CONSOLE BOX CARPET(a) Install the console box carpet.
18. INSTALL CONSOLE BOX REAR COVER(a) Engage the 8 claws and install the console box rear
cover.
19. INSTALL SHIFTING HOLE COVER SUB-ASSEMBLY (for Manual Transaxle)(a) Engage the 6 claws and install the shifting hole
cover.
B118993
B118992
B118991
B118990
-
IPIP80 INSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback)
20. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)(a) Install the shift lever knob.
21. INSTALL COWL SIDE TRIM BOARD RH (See page IR-81)
22. INSTALL COWL SIDE TRIM BOARD LH (See page IR-81)
23. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY LH (See page IR-82)
24. INSTALL INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY RH (See page IR-81)
25. INSTALL FRONT DOOR SCUFF PLATE RH (See page IR-82)
26. INSTALL FRONT DOOR SCUFF PLATE LH (See page IR-82)
27. INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY (See page IP-29)
28. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY (See page IP-32)
29. INSTALL NO. 1 SWITCH HOLE BASE (See page IP-32)
30. INSTALL FRONT PILLAR GARNISH RH (See page IR-71)
31. INSTALL FRONT PILLAR GARNISH LH (See page IR-72)
32. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (See page IR-81)
33. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (See page IR-81)
34. CONNECT AIR INLET DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-257)
35. CONNECT DEFROSTER DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-257)
36. CONNECT AIR MIX DAMPER CONTROL CABLE SUB-ASSEMBLY (See page AC-257)
37. INSTALL AIR CONDITIONER PANEL SUB-ASSEMBLY (See page AC-257)
38. INSTALL RADIO TUNER OPENING COVER (w/o Radio Receiver) (See page AC-150)
39. INSTALL RADIO RECEIVER ASSEMBLY (See page AV-46)
40. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY CENTER (See page AC-258)
41. INSTALL COMBINATION METER ASSEMBLY (See
B118989page ME-148)
-
PINSTRUMENT PANEL LOWER INSTRUMENT PANEL (for Hatchback) IP81
I
42. INSTALL INSTRUMENT CLUSTER FINISH PANEL (See page ME-148)
43. INSTALL INSTRUMENT PANEL FINISH PANEL END RH (See page ME-149)
44. INSTALL INSTRUMENT PANEL FINISH PANEL END LH (See page ME-149)
45. CONNECT CABLE TO NEGATIVE BATTERY TERMINALTorque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
46. CHECK SRS WARNING LIGHTRS-31
-
IPIP82 INSTRUMENT PANEL REAR CONSOLE BOX (for Sedan)BODYINSTRUMENT PANELREAR CONSOLE BOX (for Sedan)COMPONENTS
CONSOLE BOX CARPET
CONSOLE UPPER REAR
PANEL SUB-ASSEMBLY
INSTRUMENT PANEL
FINISH PANEL
LOWER CENTER
REAR CONSOLE BOX ASSEMBLY
SHIFT LEVER KNOB
SUB-ASSEMBLY
UPPER CONSOLE PANEL SUB-ASSEMBLY
UPPER CONSOLE PANEL
SUB-ASSEMBLY
for Manual Transaxle:
B132385E01
-
PINSTRUMENT PANEL REAR CONSOLE BOX (for Sedan) IP83
I
CONSOLE BOX
CUP HOLDER
CONSOLE COMPARTMENT
DOOR CUSHION
CONSOLE COMPARTMENT
DOOR LOCK SUB-ASSEMBLY
CONSOLE COMPARTMENT
DOOR SUB-ASSEMBLY
CONSOLE REAR END
PANEL SUB-ASSEMBLY
CONSOLE COMPARTMENT DOOR CUSHION
CONSOLE
COMPARTMENT
DOOR CUSHION
REAR CONSOLE BOX
B132345E01
-
IPIP84 INSTRUMENT PANEL REAR CONSOLE BOX (for Sedan)
REMOVAL1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL2. REMOVE INSTRUMENT PANEL FINISH PANEL
LOWER CENTER (See page ME-138)3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for
Manual Transaxle)(a) Remove the shift lever knob.
4. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY(a) Shift the shift lever into the N position.(b) Disengage the 5 clips and the claw and remove the
upper console panel.
5. REMOVE CONSOLE UPPER REAR PANEL SUB-ASSEMBLY(a) Disengage the 3 clips and 3 claws.(b) Disconnect the connector and remove the console
upper rear panel.
B132387
B132347
B132348
-
PINSTRUMENT PANEL REAR CONSOLE BOX (for Sedan) IP85
I
6. REMOVE CONSOLE BOX CARPET(a) Remove the console box carpet.
7. REMOVE REAR CONSOLE BOX ASSEMBLY(a) Disconnect the clamp.(b) Remove the 2 bolts and 2 screws.(c) Disengage the 4 claws and remove the rear console
box.
DISASSEMBLY1. REMOVE CONSOLE REAR END PANEL SUB-
ASSEMBLY(a) Remove the 2 screws.(b) Disengage the 4 claws and 4 clips and remove the
console rear end panel.
B132346
B132349
B132350
-
IPIP86 INSTRUMENT PANEL REAR CONSOLE BOX (for Sedan)
2. REMOVE CONSOLE BOX CUP HOLDER(a) Using a screwdriver with its tip wrapped in
protective tape, prize the hinge portion of the cup holder from side to side while being careful not to apply excessive load to the axis of the instrument panel upper, and remove the cup holder.
3. REMOVE CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY(a) Remove the 4 screws and remove the console
compartment door.
4. REMOVE CONSOLE COMPARTMENT DOOR LOCK SUB-ASSEMBLY(a) Remove the 2 screws and remove the console
compartment door lock.
5. REMOVE CONSOLE COMPARTMENT DOOR CUSHION(a) for Console compartment door:
(1) Remove the console compartment door cushion.
Protective
Tape
B132351E01
B132353
B132354
B132355
-
PINSTRUMENT PANEL REAR CONSOLE BOX (for Sedan) IP87
I
(b) for Console rear end panel:(1) Remove the console compartment door
cushion.
REASSEMBLY1. INSTALL CONSOLE COMPARTMENT DOOR
CUSHION(a) for Console compartment door:
(1) Install the console compartment door cushion.
(b) for Console rear end panel:(1) Install the console compartment door cushion.
2. INSTALL CONSOLE COMPARTMENT DOOR LOCK SUB-ASSEMBLY(a) Install the console compartment door lock with the 2
screws.
3. INSTALL CONSOLE COMPARTMENT DOOR SUB-ASSEMBLY(a) Install the console compartment door lock with the 4
screws.
B132352
B132355
B132352
B132354
B132353
-
IPIP88 INSTRUMENT PANEL REAR CONSOLE BOX (for Sedan)
4. INSTALL CONSOLE BOX CUP HOLDER(a) Engage the hinge portion of the cup holder and
install the cup holder.
5. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY(a) Engage the 4 claws and 4 clips.(b) Install the console rear end panel with the 2 screws.
INSTALLATION1. INSTALL REAR CONSOLE BOX ASSEMBLY
(a) Engage the 4 claws and install the rear console box.(b) Install the 2 bolts and 2 screws.(c) Connect the clamp.
2. INSTALL CONSOLE BOX CARPET(a) Install the console box carpet.
B132389
B132350
B132349
B132346
-
PINSTRUMENT PANEL REAR CONSOLE BOX (for Sedan) IP89
I
3. INSTALL CONSOLE UPPER REAR PANEL SUB-ASSEMBLY(a) Connect the connector.(b) Engage the 3 clips and 3 claws and install the
console upper rear panel.
4. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY(a) Engage the 5 clips and the claw and install the
upper console panel.
5. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)(a) Install the shift lever knob.
6. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER (See page ME-142)
7. CONNECT CABLE TO NEGATIVE BATTERY TERMINALTorque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)
B132348
B132347
B132388
01.pdf02.pdf03.pdf04.pdf05.pdf06.pdf07.pdf08.pdf09.pdf10.pdf11.pdf