integrated column planning / installation …...thickness of the custom cabinet panel. the door...
TRANSCRIPT
Effective 3/20 | WCAG
INTEGRATED COLUMNPLANNING / INSTALLATION GUIDE
Page 2 of 19 | Effective 3/20 | WCAG
24" (610 mm)finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
23 3/4"(603 mm)
24" (610 mm)
25"(635 mm)
11 3/8"*(288 mm)
25 1/2"(648 mm)
24" (610 mm)min. depth
84"(2134 mm)
24" (610 mm)finished width
4"(102 mm)finishedreturn*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
24-INCH INTEGRATED COLUMN REFRIGERATOR
Notes
Refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 14" (356 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
24" (610 mm)finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
23 3/4"(603 mm)
24" (610 mm)
25"(635 mm)
11 3/8"*(288 mm)
25 1/2"(648 mm)
24" (610 mm)min. depth
84"(2134 mm)
24" (610 mm)finished width
4"(102 mm)finishedreturn*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
INTEGRATED COLUMNFLUSH INSTALLATION
24-INCH INTEGRATED COLUMN REFRIGERATOR
Page 3 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
30-INCH INTEGRATED COLUMN REFRIGERATOR
30-INCH INTEGRATED COLUMN REFRIGERATOR
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
30" (762 mm) finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
24" (610 mm)min. depth
84"(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the refrigerator. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 16" (406 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCR3001P30-INCH INTEGRATED COLUMNREFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
30" (762 mm) finished width
CUTOUT DIMENSIONS – RETROFIT INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
24" (610 mm)min. depth
84"(2134 mm)
Page 4 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
18-INCH INTEGRATED COLUMN FREEZER
18-INCH INTEGRATED COLUMN FREEZER
SKSCF1801P18" INTEGRATEDCOLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
18" (457 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION SINGLE COLUMN
17 3/4" (451 mm) finished width
4"(102 mm)finishedreturn*
24" (610 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
1 3/8" (35 mm)
1/4"(6 mm)
min.
1/4"
min.(6 mm)
90°
115°
8 3/4"*(223 mm)
25"(635 mm)
19 1/2"(495 mm)
18"
17 3/4"(451 mm)
3/4"(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – FLUSH INSTALLATION WITH TRIM PIECE
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
8 3/4"*(223 mm)
25"(635 mm)
19 1/2"(495 mm)
18"
17 3/4"(451 mm)
3/4"(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
8 3/4"*(223 mm)
17 3/4"(451 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
Optional Frame Kit SKSFK800CS can be installed for a finished look.
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"(19 mm)**
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Freezer can be installed flush or proud with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the freezer fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold water supply in the home.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This freezer is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 11" (279 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
SKSCF1801P18" INTEGRATEDCOLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
18" (457 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION SINGLE COLUMN
17 3/4" (451 mm) finished width
4"(102 mm)finishedreturn*
24" (610 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
1 3/8" (35 mm)
1/4"(6 mm)
min.
1/4"
min.(6 mm)
90°
115°
8 3/4"*(223 mm)
25"(635 mm)
19 1/2"(495 mm)
18"
17 3/4"(451 mm)
3/4"(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – FLUSH INSTALLATION WITH TRIM PIECE
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
8 3/4"*(223 mm)
25"(635 mm)
19 1/2"(495 mm)
18"
17 3/4"(451 mm)
3/4"(19 mm)**
(457 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
8 3/4"*(223 mm)
17 3/4"(451 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
Optional Frame Kit SKSFK800CS can be installed for a finished look.
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
3/4"(19 mm)**
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
5"(127 mm)electricallocation
4"(102 mm)
water location
Page 5 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
24-INCH INTEGRATED COLUMN FREEZER
SKSCF2401P24" INTEGRATEDCOLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
24" (610 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
11 3/8"*(288 mm)
25"(635 mm)
25 1/2"(648 mm)
24"
23 3/4"(603 mm)
3/4"(19 mm)**
(610 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Freezer can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the freezer fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold water supply in the home.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This freezer is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 14" (356 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
SKSCF2401P24" INTEGRATEDCOLUMN FREEZER
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
24" (610 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
1/8"(3 mm)
min.
1/8"
min.(3 mm)
90°
115°
11 3/8"*(288 mm)
25"(635 mm)
25 1/2"(648 mm)
24"
23 3/4"(603 mm)
3/4"(19 mm)**
(610 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
Page 6 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
30-INCH INTEGRATED COLUMN FREEZER
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCF3001P30-INCH INTEGRATEDCOLUMN FREEZER
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Freezer can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the freezer fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for automatic icemaker operation. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the freezer. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold water supply in the home.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This freezer is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 16" (406 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
30" (762 mm) finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCF3001P30-INCH INTEGRATEDCOLUMN FREEZER
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
29 3/4"(756 mm)
30" (762 mm)
25"(635 mm)
13 7/8"*(352 mm)
31 1/2"(800 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
4"(102 mm)
water location
25" (635 mm)min. depth
84"(2134 mm)
Page 7 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
18-INCH INTEGRATED COLUMN WINE REFRIGERATOR
18-INCH INTEGRATED COLUMN WINE REFRIGERATOR
CUTOUT DIMENSIONS – FLUSH INSTALLATION
SKSCW181RP18" INTEGRATED COLUMNWINE REFRIGERATOR WITHOUT TRIM PIECE
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
18" (457 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
3/4"(19 mm)**
90°
115°19 1/2"
(495 mm)
17 3/4"(451 mm)
8 3/4"*(223 mm)
25"(635 mm) 1/4"
(6 mm)min.
1/4"
min.(6 mm)
18" (457 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
Notes
Wine refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the wine refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This wine refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 11" (279 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
SKSCW181RP18" INTEGRATED COLUMNWINE REFRIGERATOR WITHOUT TRIM PIECE
CUTOUT DIMENSIONS – FLUSH INSTALLATION SINGLE COLUMN
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
18" (457 mm) finished width
4"(102 mm)finishedreturn*
25" (635 mm)min. depth
84"(2134 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
1 3/8" (35 mm)
3/4"(19 mm)**
90°
115°19 1/2"
(495 mm)
17 3/4"(451 mm)
8 3/4"*(223 mm)
25"(635 mm) 1/4"
(6 mm)min.
1/4"
min.(6 mm)
18" (457 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
Page 8 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
24-INCH INTEGRATED COLUMN WINE REFRIGERATOR
24-INCH INTEGRATED COLUMN WINE REFRIGERATOR
24" (610 mm)finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP24-INCH INTEGRATED COLUMNWINE REFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
23 3/4"(603 mm)
24" (610 mm)
25"(635 mm)
11 3/8"*(288 mm)
25 1/2"(648 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
25" (635 mm)min. depth
84"(2134 mm)
CUTOUT DIMENSIONS – FLUSH INSTALLATION
Notes
Wine refrigerator can be installed flush with 3/4" custom panel or optional stainless steel panel kit.
With a 25" (635 mm) cutout depth, the front face of the wine refrigerator fits flush with 25" (635 mm) depth adjacent cabinets.
Electrical
A 115V, 60Hz., 15 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
SINGLE COLUMN
Notes
Door Swing Clearances – The installation must allow for clearances to adjacent walls or cabinets. This wine refrigerator is equipped with a 2-position door stop. The factory-set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted.
Door Handle Clearances – The Door Handle depth must be added to the dimension noted to determine the total clearances required from adjacent cabinets or walls. This clearance will vary depending on the custom handle used. When using the Stainless Steel Door Panel Kit w/Handle or the Brushed Aluminum Handle (optional accessories), the door handle clearance with door open 115° is 14" (356 mm).
INSTALLATION CLEARANCES – FLUSH INSTALLATION
TOP VIEW
24" (610 mm)finished width
CUTOUT DIMENSIONS – FLUSH INSTALLATIONSINGLE COLUMN
4"(102 mm)finishedreturn*
TOP VIEW
INSTALLATION CLEARANCES – FLUSH INSTALLATION
SKSCW241RP24-INCH INTEGRATED COLUMNWINE REFRIGERATOR
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension.
*
1 3/8" (35 mm)
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
*
3/4"(19 mm)**
115°
90°
1/8"(3 mm)
1/8"
min. min.(3 mm)
23 3/4"(603 mm)
24" (610 mm)
25"(635 mm)
11 3/8"*(288 mm)
25 1/2"(648 mm)
1 1/4"*(32 mm)
5"(127 mm)electricallocation
25" (635 mm)min. depth
84"(2134 mm)
Page 9 of 19 | Effective 3/20 | WCAG
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Handle(Handle size and position mustbe considered to avoid interference)
Adjacent Handle(Handle size and position mustbe considered to avoid interference)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)Hi
nge
at 1
15° O
peni
ngAdjacent Cabinet /Appliance Closed Door Panel
Hin
ge a
t 90°
Ope
ning
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Cabinet /Appliance
Adjacent Cabinet /Appliance with Custom Door Panel
Closed Door Panel
Closed Custom Door Panel
Hing
e at
115
° Ope
ning
Hin
ge a
t 90°
Ope
ning
TOP VIEW DOOR SWING RANGE DIMENSIONS
3/4"(19 mm) 1 1/2"
(38 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Handle(Handle size and position mustbe considered to avoid interference)
Adjacent Handle(Handle size and position mustbe considered to avoid interference)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Hing
e at
115
° Ope
ning
Adjacent Cabinet /Appliance Closed Door Panel
Hin
ge a
t 90°
Ope
ning
4" (102 mm)
3" (76 mm)
2" (51 mm)
1" (25 mm)
Adjacent Cabinet /Appliance
Adjacent Cabinet /Appliance with Custom Door Panel
Closed Door Panel
Closed Custom Door Panel
Hing
e at
115
° Ope
ning
Hin
ge a
t 90°
Ope
ning
TOP VIEW DOOR SWING RANGE DIMENSIONS
3/4"(19 mm) 1 1/2"
(38 mm)
Notes
The installation must allow for proper clearances to adjacent appliances, walls or cabinets. There should be no interference when doors are opened.
The space needed for the hinge and the distance to the adjacent cabinetry and its handle is shown with both 3/4" (19 mm) and 1 1/2" (38 mm) thick door panels.
If interference is an issue, the following solutions can be considered:
• Limit the door swing angle to 90° with a door stop pin inserted into the hinge.
• Install a spacer between the appliance and the opposing element that creates the interference.
• If the door panel thickness is larger than 3/4" (19mm), consider reducing it.
• Rearrange surrounding cabinetry or appliances to eliminate the interference.
• Create a protruding cutout for the appliance (see page 6 for “retrofit” installation).
INTEGRATED COLUMNFLUSH INSTALLATION
DOOR SWING DIMENSIONS
3/4" (19 MM) FLUSH DOOR PANEL
1 1/2" (38 MM) FLUSH DOOR PANEL
Page 10 of 19 | Effective 3/20 | WCAG
Notes
When installing multiple columns in a flush installation with the same door swing (handle to hinge), considerations must be made to avoid door swing interference. The examples shown assume a 3/4" panel and the Signature Kitchen Suite handle.
Door panel thickness, handle size / position and door swing range should always be considered when determining the size of the spacer in any installation. See page 6 for details on door swing dimensions for proper planning.
Integrated columns can be combined in cutout widths of 42", 48", 54" and 60". - The SKSFJ800P Joining Kit is required between units (kit included with all freezer columns.) - Reference the cutout dimensions for each column for detailed dimensions. - A minimum 15 amp (115V, 60Hz) power supply is required for each individual column. - A cold water supply is required for water dispenser and automatic icemaker operation for each applicable column.
1 3/4" (44 mm) min.spacer required*
TOP VIEW DOOR OPEN 115˚ HANDLE TO HINGE
1 3/4" (44 mm) min.spacer required*
Handle size and positionmust be considered toavoid interference.
TOP VIEW DOOR OPEN 90˚ HANDLE TO HINGE
3/4" (19 mm) min.spacer required**
3/4" (19 mm) min.spacer required**
*When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, a minimum spacer of 1 3/4" (44 mm) between units is required to open each door 115° without interference.
**When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, the door swing can be limited to 90°, reducing the minimum spacer between units to 5/8" (16 mm).
Handle size and positionmust be considered toavoid interference.
1 3/4" (44 mm) min.spacer required*
TOP VIEW DOOR OPEN 115˚ HANDLE TO HINGE
1 3/4" (44 mm) min.spacer required*
Handle size and positionmust be considered toavoid interference.
TOP VIEW DOOR OPEN 90˚ HANDLE TO HINGE
3/4" (19 mm) min.spacer required**
3/4" (19 mm) min.spacer required**
*When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, a minimum spacer of 1 3/4" (44 mm) between units is required to open each door 115° without interference.
**When using the Stainless Steel Door Panel Kit w/Handle or 3/4" (19 mm) custom panels with our optional Brushed Aluminum Handle, the door swing can be limited to 90°, reducing the minimum spacer between units to 5/8" (16 mm).
Handle size and positionmust be considered toavoid interference.
INSTALLATION CLEARANCES – MULTIPLE COLUMNS WITH SAME DOOR SWING (HANDLE TO HINGE)
INSTALLATION PLANNING - MULTIPLE COLUMNS
TOP VIEW – DOOR OPEN 115˚ HANDLE TO HINGE
TOP VIEW – DOOR OPEN 90˚ HANDLE TO HINGE
INTEGRATED COLUMNFLUSH INSTALLATION
Page 11 of 19 | Effective 3/20 | WCAG
CABINETRY PLANNING
FRAMED CABINET (NORTH AMERICA)
FRAMELESS CABINET (EUROPEAN)
FLUSH INSET
FLUSH INSET
Framed Cabinet
Cabinet doorhinges mountto the face frame
Frameless (European) Cabinet
Cabinet doorhinges mountto the cabinetinterior
CABINETRY PLANNING
Flush Inset
Appliance25" (635 mm)Cutout Depth
Door Panel
25" (635 mm)Cutout Depth
Flush Inset
Door Panel
Appliance
Filler required with afinished return on bothsides of the appliance
Framed Cabinet
Cabinet doorhinges mountto the face frame
Frameless (European) Cabinet
Cabinet doorhinges mountto the cabinetinterior
CABINETRY PLANNING
Flush Inset
Appliance25" (635 mm)Cutout Depth
Door Panel
25" (635 mm)Cutout Depth
Flush Inset
Door Panel
Appliance
Filler required with afinished return on bothsides of the appliance
INTEGRATED COLUMNFLUSH INSTALLATION
Notes
Integrated column appliances are designed to accommodate nearly any type of cabinetry door installation. The required cutout depth depends on the desired cabinetry and custom panel execution, whether North American styles that feature a face frame or European styles that are frameless.
CUSTOM PANEL PLANNING
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs. 24-Inch Integrated Column – 53 lbs. 18-Inch Integrated Column – 44 lbs
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
Page 12 of 19 | Effective 3/20 | WCAG
INTEGRATED COLUMNFLUSH INSTALLATION
CUSTOM PANEL DIMENSIONS
18-INCH INTEGRATED COLUMN FREEZER
18-INCH INTEGRATED COLUMN WINE REFRIGERATOR
24-INCH INTEGRATED COLUMN WINE REFRIGERATOR
24-INCH INTEGRATED COLUMN REFRIGERATOR AND FREEZER
30-INCH INTEGRATED COLUMN REFRIGERATOR AND FREEZER
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
SKSCF1801P18" INTEGRATEDCOLUMN FREEZER
Door PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm) 4" (102 mm) 4" (102 mm)
Door Panel
(451 mm)17 3/4"
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
Door Panel
(451 mm)17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCF2401P 24-INCH INTEGRATEDCOLUMN FREEZER
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
(603 mm)23 3/4"
Door PanelDoor PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm)4" (102 mm)
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
41 1/2" (1054 mm)Toekick Width
47 1/2" (1207 mm)Toekick Width
4" (102 mm) 4" (102 mm) 4" (102 mm) 4" (102 mm)
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4"(1213 mm)
(756 mm)29 3/4"
DUAL 18" AND 30" COLUMN DUAL 24" AND 30" COLUMN
SKSCF3001P30-INCH INTEGRATEDCOLUMN FREEZER
Door Panel Door Panel 79 7/8"(2029 mm)
(451 mm)17 3/4"
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 30" AND 30" COLUMN
59 3/4"(1518 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(756 mm)29 3/4"
Door Panel
4" (102 mm) 4" (102 mm) 4" (102 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
4" (102 mm)
Door Panel
(451 mm)17 3/4"
4" (102 mm)4" (102 mm)
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 3/4" (1213 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
SKSCW181RP18" INTEGRATEDWINE COLUMN
79 7/8"(2029 mm)
9 3/8"(238 mm)
7 1/16"(179.5 mm)
3 3/16"(81 mm)
3 3/16"(81 mm)
(451 mm)17 3/4"
4" (102 mm)
SKSCW181RP18" INTEGRATEDWINE COLUMN
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
79 7/8"(2029 mm)
9 3/8"(238mm)
7 1/16"(179.5 mm)
(603 mm)23 3/4"
3 3/16"(81 mm)
3 3/16"(81 mm)
4" (102 mm)
Page 13 of 19 | Effective 3/20 | WCAG
CUSTOM PANEL DIMENSIONS FOR MULTIPLE COLUMNS
Door Panel
(451 mm)17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
(603 mm)23 3/4"
Door PanelDoor PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)Toekick Width
47 1/2" (1207 mm)Toekick Width
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm)
4" (102 mm)4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
DUAL 24-INCH AND 24-INCH INTEGRATED COLUMNS
DUAL 24-INCH AND 30-INCH INTEGRATED COLUMNS
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs. 24-Inch Integrated Column – 53 lbs. 18-Inch Integrated Column – 44 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
DUAL 18-INCH AND 24-INCH INTEGRATED COLUMNS
Door Panel
(451 mm)17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
(603 mm)23 3/4"
Door PanelDoor PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)Toekick Width
47 1/2" (1207 mm)Toekick Width
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm)
4" (102 mm)4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
INTEGRATED COLUMNFLUSH INSTALLATION
Door Panel
(451 mm)17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
(603 mm)23 3/4"
Door PanelDoor PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)Toekick Width
47 1/2" (1207 mm)Toekick Width
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm)
4" (102 mm)4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
Page 14 of 19 | Effective 3/20 | WCAG
OPTIONAL ACCESSORIES
INTEGRATED COLUMNOPTIONAL ACCESSORIES
Stainless Steel Panel Kit for Integrated Column Refrigerators and Freezers
Units can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and one handle. This kit is reversible and can be used in both Right Hand and Left Hand door swing installations.
SKSPK185CS –Stainless Steel Panel Kit for 18-inch Integrated Column Freezer
SKSPK245CS – Stainless Steel Panel Kit for 24-inch Integrated Column Refrigerator and Freezer
SKSPK305CS – Stainless Steel Panel Kit for 30-inch Integrated Column Refrigerator and Freezer
Stainless Steel Panel Kit for 18-inch Integrated Column Wine Refrigerator
This unit can be installed with an optional Stainless Steel Panel Kit. Kit includes one door panel, one toe kick and one handle. Order right or left hinge option, depending on desired installation.
Right Hinge – 1 Horizontal brushed hairlines for right hinge installation, opening from left to right
Left Hinge – 1 Horizontal brushed hairlines for left hinge installation, opening from right to left
SKSWK185RS – 18" Wine Column Stainless Kit, Right Hinge
SKSWK185LS – 18" Wine Column Stainless Kit, Left Hinge
SKSWK245RS – 24" Wine Column Stainless Kit, Right Hinge
SKSWK245LS – 24" Wine Column Stainless Kit, Left Hinge
Handles for Use With Custom Panels
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
SKSHK480HS – 48" (1219 mm) Long Handle – Brushed Aluminum
Joining Kit for Dual/Multiple Column Installation
SKSFJ800P – This kit is required for installation when a wine column is installed with another wine column, refrigerator column or French door column. This kit is included with all freezer columns.
SKSCW241RP24-INCH INTEGRATED COLUMNWINE REFRIGERATOR
OPTIONAL ACCESSORIES
SKSCW181RP18-INCH INTEGRATED COLUMNWINE REFRIGERATOR
OPTIONAL ACCESSORIES
SKSCF3001P30-INCH INTEGRATEDCOLUMN FREEZER
OPTIONAL ACCESSORIES
SKSCF2401P24-INCH INTEGRATEDCOLUMN FREEZER
OPTIONAL ACCESSORIES
SKSCF1801P18-INCH INTEGRATEDCOLUMN FREEZER
OPTIONAL ACCESSORIES
Page 15 of 19 | Effective 3/20 | WCAG
36-INCH BUILT-IN FRENCH DOOR REFRIGERATOR
CUSTOM PANEL DIMENSIONS
INTEGRATED COLUMNFLUSH INSTALLATIONSKSFD3604P36-INCH BUILT-IN FRENCH DOOR REFRIGERATOR
CUSTOM PANEL DIMENSIONS
17 13/16"(452 mm)
A
B
C
A
17 13/16"(452 mm)
(1254 mm)49 3/8"
(230 mm)9 1/16"
(533 mm)21"
(908 mm)35 3/4"
4" (102 mm)
OPTIONAL ACCESSORIES
SKSFD3604P36" INTEGRATED FRENCHDOOR REFRIGERATOR
OPTIONAL ACCESSORIES
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Panel Weight:
A – Fresh food door panels: 33 lbs. B – Convertible drawer panel: 22 lbs. C – Freezer drawer panel: 33 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
Door Handles: Handles are not included with the refrigerator. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
SKSPK360FS – Stainless Steel Panel Kit for 36-inch Built-in French Door Refrigerator
This refrigerator can be installed with an optional Stainless Steel Panel Kit. Kit includes two fresh food door panels, one convertible drawer panel, one freezer drawer panel, one toe kick and four handles.
Handles for Use With Custom Panels
SKSHK310HS – 31 11/16" (805 mm) Medium Handle – Brushed Aluminum
Page 16 of 19 | Effective 3/20 | WCAG
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER AND 24" REFRIGERATOR COLUMN
24" (610 mm)min. depth
84"(2134 mm)
4"(102 mm)finishedreturn*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
41 1/2" (1054 mm)finished width
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER AND 30" REFRIGERATOR COLUMN
24" (610 mm)min. depth
84"(2134 mm)
4"(102 mm)finishedreturn*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
47 1/2" (1207 mm)finished width
1 3/8" (35 mm)
2 3/4"(70 mm)
2 3/4"(70 mm)
5"(127 mm)electricallocation
4" (102 mm)water location
4" (102 mm)water location
5"(127 mm)electricallocation
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER AND 24" REFRIGERATOR COLUMN
24" (610 mm)min. depth
84"(2134 mm)
4"(102 mm)finishedreturn*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
41 1/2" (1054 mm)finished width
1 3/8" (35 mm)
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER AND 30" REFRIGERATOR COLUMN
24" (610 mm)min. depth
84"(2134 mm)
4"(102 mm)finishedreturn*
A minimum 4" (102 mm) finished return that matches the cabinet exterior is recommended on all sides and the top of the cutout opening. The shaded area will be visible after installation.
An optional Frame Kit can be used to provide a finished look to unfinished cabinet returns.
*
47 1/2" (1207 mm)finished width
1 3/8" (35 mm)
2 3/4"(70 mm)
2 3/4"(70 mm)
5"(127 mm)electricallocation
4" (102 mm)water location
4" (102 mm)water location
5"(127 mm)electricallocation
CUTOUT DIMENSIONS – RETROFIT INSTALLATION
18" FREEZER AND 24" REFRIGERATOR COLUMN
18" FREEZER AND 30" REFRIGERATOR COLUMN
Notes
The 18" integrated column freezer has an actual width of 17 1/2" (445 mm) to accommodate a retrofit installation. This will allow you to combine the 18" freezer column with a 24" refrigerator column in a 41 1/2" (1054 mm) cutout or with a 30" refrigerator column in a 47 1/2" (1207 mm) cutout.
Electrical
A minimum 15 amp (115V, 60Hz) power supply is required for each individual column. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
A cold water supply is required for water dispenser and automatic icemaker operation for each individual column. Water pressure must be between 20 and 120 p.s.i.
Tubing should be long enough to extend to the front of the unit. Allow enough tubing to accommodate a bend leading into the water line connection.
Water line can enter an opening through floor or back wall.
Install a shut-off valve between the icemaker water valve and cold water supply in the home.
INTEGRATED COLUMNRETROFIT INSTALLATION
Page 17 of 19 | Effective 3/20 | WCAG
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER AND 24-INCH INTEGRATED COLUMN REFRIGERATOR
TOP CUTOUT VIEW – 18-INCH INTEGRATED COLUMN FREEZER AND 30-INCH INTEGRATED COLUMN REFRIGERATOR
INTEGRATED COLUMNRETROFIT INSTALLATION
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"(3 mm)
min.
90°
115°
8 3/4"*(223 mm)
41 1/2" cutout (1054 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
18-INCH INTEGRATED COLUMN FREEZERAND24-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.(3 mm)
23 3/4"(603 mm)
11 3/8"*(288 mm)
24"(610 mm)
25 1/2"(648 mm)
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension. *
3/4"(19 mm)**
Optional Frame Kit SKSFK800CS can be installed for a finished look.
TOP VIEW
1/8"(3 mm)
min.
90°
115°
8 3/4"*(223 mm)
47 1/2" cutout (1207 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
18-INCH INTEGRATED COLUMN FREEZERAND30-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.(3 mm)
29 3/4"(756 mm)
13 7/8"*(352 mm)
24"(610 mm)
32 1/4"(819 mm)
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension. *
3/4"(19 mm)**
Optional Frame Kit SKSFK800CS can be installed for a finished look.
1 1/4"*(32 mm)
1 1/4"*(32 mm)
1 1/4"*(32 mm)
1 1/4"*(32 mm)
INSTALLATION CLEARANCES – RETROFIT INSTALLATION
TOP VIEW
1/8"(3 mm)
min.
90°
115°
8 3/4"*(223 mm)
41 1/2" cutout (1054 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
18-INCH INTEGRATED COLUMN FREEZERAND24-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.(3 mm)
23 3/4"(603 mm)
11 3/8"*(288 mm)
24"(610 mm)
25 1/2"(648 mm)
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension. *
3/4"(19 mm)**
Optional Frame Kit SKSFK800CS can be installed for a finished look.
TOP VIEW
1/8"(3 mm)
min.
90°
115°
8 3/4"*(223 mm)
47 1/2" cutout (1207 mm)
24"(610 mm)
20 1/4"(514 mm)
17 3/4"(451 mm)
18-INCH INTEGRATED COLUMN FREEZERAND30-INCH INTEGRATED COLUMN REFRIGERATOR
115°
90°
1/8"
min.(3 mm)
29 3/4"(756 mm)
13 7/8"*(352 mm)
24"(610 mm)
32 1/4"(819 mm)
** Varies depending on the thickness of the custom cabinet panel. The door panels in the optional Signature Kitchen Suite stainless steel door panel kit are 3/4" (19 mm) thick.
Door handle must be added to this dimension. *
3/4"(19 mm)**
Optional Frame Kit SKSFK800CS can be installed for a finished look.
1 1/4"*(32 mm)
1 1/4"*(32 mm)
1 1/4"*(32 mm)
1 1/4"*(32 mm)
Notes
In retrofit installations where the cutout is only 24" (610 mm) deep, the front face of the unit extends approximately 3/4" (19 mm) beyond 24" (610 mm) depth adjacent cabinets for a proud appearance.
The unit can be installed with 3/4" custom panel or optional stainless steel panel kit. An optional Frame Kit is recommended for a finished look.
Page 18 of 19 | Effective 3/20 | WCAG
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
DUAL 18-INCH AND 30-INCH INTEGRATED COLUMNS
DUAL 18-INCH AND 24-INCH INTEGRATED COLUMNS
Door Panel
(451 mm)17 3/4"
CUSTOM PANEL DIMENSIONS – FLUSH INSTALLATION
47 3/4" (1213 mm)
DUAL 24" AND 24" COLUMN
SKSCR2401P24-INCH INTEGRATED COLUMNREFRIGERATOR
79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
(603 mm)23 3/4"
Door PanelDoor PanelDoor Panel
DUAL 18" AND 24" COLUMN
41 3/4" (1060 mm)
41 1/2" (1054 mm)Toekick Width
47 1/2" (1207 mm)Toekick Width
(603 mm)23 3/4"
79 7/8"(2029 mm)
(451 mm)17 3/4"
4" (102 mm)
4" (102 mm)4" (102 mm)
79 7/8"
4" (102 mm)
(2029 mm)
(603 mm)23 3/4"
Door Panel
DUAL 24" AND 30" COLUMN
53 3/4"(1365 mm)
(756 mm)29 3/4"
Door Panel 79 7/8"(2029 mm)
(603 mm)23 3/4"
Door Panel
CUSTOM PANEL DIMENSIONS – RETROFIT INSTALLATION
47 1/2" (1207 mm)
DUAL 18" AND 30" COLUMN
79 7/8"(2029 mm)Door Panel
DUAL 18" AND 24" COLUMN
41 1/2" (1054 mm)
(603 mm)23 3/4"
79 7/8"(2029 mm)Door Panel
(451 mm)17 3/4"
(756 mm)29 3/4"
Door Panel
4" (102 mm)4" (102 mm)
Notes
These units are designed to be customized with decorative panels. Field-installed custom door panels or an optional Stainless Steel Panel Kit is required.
For Custom Panels: Use templates provided with units to pre-drill holes for mounting panel brackets (provided with unit). Adjustment screws and instructions also provided with units.
Maximum Total Door Panel Weights: 30-Inch Integrated Column – 64 lbs. 24-Inch Integrated Column – 53 lbs. 18-Inch Integrated Column – 44 lbs.
Design Tips
4" (102 mm) will be visible on the interior sides of the furniture return. It is recommended that both sides of each cutout panel be finished to match the cabinet exterior.
If using custom panels, a custom toe kick is required. The bottom of case is unfinished.
In retrofit installations where the cutout is 24" (610 mm) deep, the optional Frame Kit is recommended to provide a finished look.
Door Handles: Handles are not included with the units. Custom handles are required for installation. Brushed Aluminum Handles are available as an optional accessory.
INTEGRATED COLUMNRETROFIT INSTALLATION
© 2020 Signature Kitchen Suite. All rights reserved. Design, features and specifications are subject to change without notice. Specifications are for planning purposes only. Consult the product’s installation instructions for final dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your specific ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access. 1-855-790-6655 | www.signaturekitchensuite.com
OPTIONAL ACCESSORIES – RETROFIT INSTALLATIONOPTIONAL ACCESSORIES – RETROFIT INSTALLATION
SKSFK800CS – Frame Kit
All units can be installed in a 24" (610 mm) deep cutout with an optional frame kit. This kit includes two 80" (2032 mm) brushed aluminum side trim pieces. Each trim piece is 5" (127 mm) deep with a 1/8" (3 mm) front face.
SKSFJ800P - Joining Kit for Dual/Multiple Column Installation
This kit is required for installation when a wine column is installed with another wine column, refrigerator column or French door column. This kit is included with all freezer columns.
Design Tips
The Stainless Steel Panel Kit may be used in a retrofit 24" (610 mm) cutout depth installation.
For retrofit / replacement installations where the existing cutout is 24" (610 mm) deep, the optional frame kit is recommended.
Effective 3/20 | WCAG
INTEGRATED COLUMNRETROFIT INSTALLATION