intelligent power switches (ips) - stmicroelectronics · 8 gui software on pc (e.g. stsw-ips16x)...
TRANSCRIPT
-
Intelligent Power Switches
(IPS)
-
Contents
4 Technology Overview
IPS solutions 6 Product range 9 Transceiver ICs 10 Power stage characteristics
-
4
IntegrationLogicinterface
Driver &protection
Logic interface + driver + protections + power switches
BENEFITS • Increased system reliability• Part count reduction• Space saving• Built-in protection• System approach
Feedback
From a discrete solution To an intelligent solution
Powerswitches
ST offers an industrial series of intelligent power switches (IPS) for high-side and low-side configurations. An IPS integrates a control part (logic interface, drivers, and protection) with a power stage.
IPS are based on the well-consolidated bipolar, multi-power BCD and VIPower®M0 technologies.
Devices in development are designed using the latest versions of the above technologies, thus offering state-of-the-art solutions in a wide range of applications.
FEATURES• Galvanic isolation on chip• Supply voltage up to 60 V• Fast demagnetization of inductive loads• Very low R
DS(ON) supply current• Short-circuit and overcurrent protection• Undervoltage protection and overvoltage
shutdown• Loss of ground protection• Thermal protection: junction and case• Diagnostic output• Open load detection• Designed to meet IEC 61131-2 standards
Technology Overview
-
5
Typical architecture of intelligent power switch (VNI8200XP)
International standards
IPS devices are designed to safely drive every kind of load in low-voltage applications (up to 60 V), handling data in and out of the microcontroller by means of status/input signals. IPS devices are designed to comply with the following international standards for EMC and PLC equipments:
Packages
Technological evolution has led to smaller IPS devices, housed in tiny, flat, no-lead plastic packages (DFN, QFN). The high thermal capacitance of the power packages such as PowerSO-36, PowerSSO36, PowerSSO24, PowerSSO12 and HTSSOP20, allows the absorption of high-energy pulses when an inductive load is driven without any external freewheeling diode.
Concerning ISO8200B, ISO8200AQ and ISO8200BQ, they are designed to comply with the following international standards for isolation characteristics and tests:
X8
FB
SDO / IN8
CLK / IN6
Output 1..8
VCC
WD / IN4
OUT_EN / IN3
WD_EN / IN2
SDI / IN5
SEL1 / IN1
SEL2
BOOT
PHASE
VregROW COL
DCVDD VREF
SPIparallel
watchdog
DC / DCconverter
LEDdriving
Case tempdetection
Junction tempdetection
VCC- Voutclamp
Current lim.
VCCclamp
Undervoltagedetection
Logic
PG214321 GNDFAULT TWARN
SS / IN7
• IEC 61000-4-4 (electrical fast transient/burst)• IEC 61000-4-2 (ESD, immunity test contact/air)• IEC 61000-4-5 (surge test immunity requirements)• IEC 61000-4-6 (current injection test)
• IEC 61131-2 (programmable controller, equipment requirements and tests)
• UL 1577 (isolation voltage)• IEC 61000-4-8 (power frequency magnetic field immunity
test)
• IEC 60747-5-2 (optoelectronic devices characteristics)
• I/O Safety limits according to VDE V 0884-11• UL 508 (Standard for Safety for Industrial Control
Equipment)
-
6
Output Stage
Part numberOutput Chan-nels
Output current / Channel
(lnom) (A)
Typ. RDS(on) Ohm
Supply voltage (V) AMR max.
Supply voltage (V) min.
Note Package Evaluation BoardApplication Note/
User Manual
High-side
IPS160H
1
2 0.06 65 8Open Load Diag PowerSSO-12 STEVAL-IFP028V1 AN4781
IPS160HF (*) Open Load Diag PowerSSO-12 X-NUCLEO-OUT08A1 UM2715IPS161H
0.5 0.06 65 8Open Load Diag PowerSSO-12 STEVAL-IFP034V1 AN4998
IPS161HF (*) Open Load Diag PowerSSO-12 X-NUCLEO-OUT10A1 UM2716L6370D 2 0.1 50 9.5 Adjustable IOUT PowerSO-20L6375D
0.5 0.4 50 8 SO-20
L6375S SO-8L6377D Adjustable IOUT SO-14
TDE1747FP < 0.5 60 8 Adjustable IOUT SO-14TDE1798DP
0.550 6 mini-DIP8
TDE1897RFPT0.4 50 18
SO-20 AN453TDE1898CFP SO-20 AN453TDE3247FP < 0.5 36 8 Adjustable IOUT SO-14VN540SP-E
20.05 45 10 PowerSO-10
VN751PT 0.0645 5.5
Open Load Diag PPAK STEVAL-IFP005V2VN751S 0.06 Open Load Diag SO-8
VNI2140J 2 1 0.06 45 9 Open Load Diag PowerSSO-12 STEVAL-IFP010V3 AN2985L6376D
4
0.50.64 50 9.5 PowerSO-20
VN330SP-E 0.2 45 10 PowerSO-10VN340SP-33-E 1 0.2 45 10 PowerSO-10 AN2208
VN340SP-E0.5
0.2 45 10 Per Channel Diag PowerSO-10 AN2208VNI4140K 0.08 41 10.5 Per Channel Diag PowerSO-24 AN2684
VNI4140K-32 1 0.08 41 10.5 Per Channel Diag PowerSO-24 STEVAL-IFP019V1 AN4009VNQ860-E
< 0.5 0.2741 5.5 Per Channel Diag SO-20
VNQ860SP-E 41 5.5 Per Channel Diag PowerSO-10
ISO8200AQ (**)
8
0.50.11 45 10.5
Isolated, SPI, Per Channel Diag
QFN 9x11 X-NUCLEO-OUT02A1 UM2507
ISO8200B (**) 0.11 45 10.5 Isolated PowerSO-36 STEVAL-IFP015V2 AN4373, UM2209
ISO8200BQ (**) 0.5 0.11 45 10.5 Isolated QFN 9x11STEVAL-IFP033V1
X-NUCLEO-OUT01A1AN4373, UM2209
VN808-32-E1
0.15 45 10.5 PowerSO-36 AN2443, AN2208VN808CM-32-E 0.16 45 10.5 PowerSO-36 STEVAL-IFP001V1 AN2443, AN2208
VN808CM-E
0.5
0.16 45 10.5 Logic level Inputs PowerSO-36 AN2443, AN2208VN808-E 0.15 45 10.5 PowerSO-36 AN2443, AN2208
VNI8200XP 0.11 45 10.5LED Matrix Driver, DCDC,
SPI, Per Channel DiagPowerSO-36
STEVAL-IFP022V1 X-NUCLEO-PLC01A1
AN4284, UM1918
VNI8200XP-32 1 0.11 45 10.5LED Matrix Driver, DCDC,
SPI, Per Channel DiagPowerSSO-36 STEVAL-IFP032V1 AN4862
High & Low side
TDE1708DFT (***)1
< 0.5 50 6 DFN 8L 4x4 STEVAL-IFS006V2AN2679, AN2813
TDE1707BFP (***) 0.5 50 6 SO-8 AN1213, AN495
Low side
IPS4260L
4
0.5 0.26 55 8Adjustable IOUT, Open
Load / Per Channel DiagHTSSOP-20 STEVAL-IFP029V1 UM2297
Push-Pull
L6374FP < 0.5 4 50 10.8 Push-Pull Line Driver SO-20
Notes : (*) Satisfy SIL applications requirements for interface type C (or D) Class 3 (**) Galvanic Isolated (***) The TDE1707 and TDE1708 are specific IPS developed to match all types of industrial detectors. They can be coupled with inductive, capacitive, ultra-sonic or optical detectors and can be used in high-side or in low-side driver configuration in 3-wire networks.
IPS solutions Product range
-
7
ISO8200B
STEVAL-IFP015V2
STEVAL-IFP005V2X-NUCLEO-OUT08A1
VN751PTIPS160HF
STEVAL-IFP010V3X-NUCLEO-OUT10A1
VNI2140JIPS161HF
STEVAL-IFP028V1
IPS160H
ISO8200BQ
STEVAL-IFP033V1
IPS161H
STEVAL-IFP034V1
IPS4260L
ISO8200AQ
STEVAL-IFP029V1
X-NUCLEO-OUT02A1
ISO8200BQ
X-NUCLEO-OUT01A1
VNI8200XP
STEVAL-IFP022V1STEVAL-IFP019V1
VNI4140K-32 VNI8200XP
X-NUCLEO-PLC01A1
VNI8200XP -32
STEVAL-IFP032V1
Quad Channel
Single Channel
Octal Channel
Dual Channel
Isolated IPS
-
8
GUI Software on PC(e.g. STSW-IPS16X)
IPS Evaluation Board(e.g. STEVAL-IFP034V1) Load
STEVAL-PCC009V2microcontroller based
interface board
USB SPI/GPIOs
Evaluation software STSW-IFAPGUI Expansion board plugged on the Nucleo board (i.e. Nucleo pack)
USB
EVALUATION BOARD BASIC SETUP
NUCLEO BOARD SETUP
-
9
Industrial transceiver ICs for IO-LINK and SIO mode
By using a state-of-the-art technology (MultiPower BCD) that allows the design of the logic part and robust LV power MOSFETs allowing hundreds kHz switching frequency in the same chip, ST offers an efficient, compact and cost-effective solution to drive any 3-wire digital sensor. Modern sensors and actuators require:
• remote service• standardization• sensor functionality verification• diagnostics• monitoringThe L6360, L6362A and L6364 I/O industrial transceiver ICs meet all these requirements. These ICs offer the market IO-LINK sensors/actuators that work without special cables. They feature an advanced solution that can even be integrated in old systems, that is neutral to any field bus, and keeps the point-to-point communication. Industrial transceiver ICs are designed in order to guarantee EMC immunity (burst/fast transient, ESD contact/air, surge pulse, RF emission/conduced), according to the IO-LINK specification and SIO mode requirements.
Industrial transceiver IC product range
Part numberSupply
voltage (V)VDD (V)
Output current (A)
Imax linear reg. (mA)
TechnologyOutput
channelsInput
channelsPackage
L6360 (Master) 18 to 32.5 3.3/5 0.5 65 MultiBCD 2 2 QFN 26L 3.5 x 5 mm
L6362A (Device) 7 to 36 3.3/5 0.22 10 MultiBCD 1 1 DFN 12L 3 x 3 mm
L6364Q (Device) 6 to 35 3.3/5 0.25/0.5(**) 50 MultiBCD 2 2 QFN 20L 4 x 4 mm
L6364W (Device)(*) 6 to 35 3.3/5 0.25/0.5(**) 50 MultiBCD 2 2 CSP 19 2.5 x 2.5 mm
Notes: (*) available end of Q4 2020 (**) join mode
IO-Link evaluation boards
Order code DescriptionApplication note / User manual
STEVAL-IDP004V2 IO-Link master multi-port evaluation board based on L6360 AN5041
STEVAL-IOM001V1 IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo UM2414
STEVAL-IDP003V1 IO-Link industrial modular sensor board based on L6362A AN5041
STEVAL-IOD003V1 IO-Link (PHY) device evaluation board based on L6362A with Arduino connectors for STM32 Nucleo UM2424
P-NUCLEO-IOM01M1 STM32 Nucleo pack for IO-Link master based on L6360 device with IO-Link v1.1 (PHY and stack) UM2421
P-NUCLEO-IOD01A1 STM32 Nucleo pack for IO-Link device based on L6362A device fully compatible with IO-Link v1.1.3 (PHY and stack) UM2425
X-NUCLEO-IOD02A1 Expansion board IO-Link device based on L6364Q device fully compatible with IO-Link v1.1 (PHY and stack) UM2741
P-NUCLEO-IOD02A1(*) STM32 Nucleo pack for IO-Link device based on L6364 device fully compatible with IO-Link v1.1 (PHY and stack) UM2782
STEVAL-BFA001V2B Multi-sensor predictive maintenance kit with L6362A and IO-Link stack v.1.1 UM2663
Notes: (*) Available end Q4 2020
IPS Solutions Transceiver ICs
-
10
L6362A
P-NUCLEO-IOD01A1
L6360
STEVAL-IOM001V1
L6360
STEVAL-IDP004V2
STEVAL-IOD003V1 X-NUCLEO-IOD02A1
L6362A L6364Q
STEVAL-BFA001V2B STEVAL-IDP003V1
L6362A L6362A
L6360
P-NUCLEO-IOM01M1
-
11
VIPowertechnology SO-20PowerSO-10
50 mΩ
SO-8
60 mΩ
PPAK
60 mΩ
PowerSSO-24
200 mΩ
200 mΩ
270 mΩ 270 mΩ
IPS160H 2A Single HSS
IPS161H 0.5A Single HSS
VN751 2A Single HSS
VN540 2A Single HSS
VN2140J 1A Dual HSS
VN330SP 0.5A Quad HSS
VNQ860 0.25A Quad HSS
VN340SP 0.5A Quad HSS
VNI4140K 0.5A Quad HSS
PowerSSO-12
80 mΩ
60 mΩ
60 mΩ
IPS160HF2A Single HSS
IPS161HF0.5A single HSS
60 mΩ
60 mΩ
80 mΩ
VNI4140K-32 1A Quad HSS 80 mΩ
VIPowertechnology PowerSSO-36PowerSO-36
150 mΩVN808/CM
0.5A Octal HSS
150 mΩVN808/CM-32 1A Octal HSS
VNI8200XP 0.5A Octal HSS
ISO8200B 0.5A Octal HSS
ISO8200A 0.5A Octal HSS
QFN 9x11 32L
110 mΩ
VNI8200XP-32 1A Octal HSS
110 mΩ
110 mΩ 110 mΩ
110 mΩ
IPS Solutions Power stage characteristics
-
Order code: BRIPS0920
© STMicroelectronics - September 2020 - Printed in United Kingdom - All rights reservedST and ST logo are trademarks or registered trademarks of STMicroelectronics International NV or its affiliates in the EU and/or other countries. For additional information about ST trademarks, please refer to www.st.com/trademarks.
All other product or service names are the property of their respective owners.
For more information on ST products and solutions, visit www.st.com
400 mΩ
400 mΩ 400 mΩ
400 mΩ
400 mΩ
400 mΩ
400 mΩ
DIP-8BCD technology
High Side Switch (HSS)
Low Side Switch (LSS)
SO-8 SO-14HTSSOP20 SO-20
100 mΩ
PowerSO-20
L6370 2A Single
L6375 0.5A Single
L6377 0.5A Single
TDE1897 0.5A Single
TDE1898 0.5A Single
L6374 0.1A Quad
L6376D 0.5A Quad
IPS4260L 0.5 to 2A Quad
260 mΩ
640 mΩ
Notes: (*) Available end Q4 2020
0.5 A
DIP-8Bipolar technology DFN 4x4
0.5 A
SO-8 SO-14
TDE1798Single HSS
TDE1747Single HSS
TDE1708DFTSingle HSS/LSS
TDE1707Single HSS/LSS 0.5 A
0.2 A
0.5 A
0.22 A
BCD technology QFN-26L 3.5x5 DFN-12L 3x3
0.25 A
QFN 20L4x4
L6360
L6362A
L6364Q
0.25 A
CSP 2.5 x 2.5 mm
L6364W (*)
IO-LINK communicationtransceivers