introduction - latest seminar topics for … seminar report on distributed firewall 09203005 a...

A Seminar Report On Distributed Firewall 09203005

A firewall is system or group of system (router, proxy, gateway…) that implements a set of security rules to enforce access control between two networks to protect “inside” network from “outside network. It may be a hardware device or a software program running on a secure host computer. In either case, it must have at least two network interfaces, one for the network it is intended to protect, and one for the network it is exposed to. A firewall sits at the junction point or gateway between the two networks, usually a private network and a public network such as the Internet.

Hardware Firewall: Computer with Firewall Software: Hardware firewall providing protection to Computer running firewall software to provide a Local Network protection

A Firewall is… A physical manifestation of your security policy. One component of overall security architecture. A mechanism for limiting access by network elements and protocols.

A Firewall is not… A cure-all for security shortcomings on platforms or in applications. Complete security architecture. Something that should be configured “on-the-fly”. Effective protection against viruses (typically).

M.Tech CSE NITJ P a g e | 1

INTRODUCTION


Conventional firewalls rely on the notions of restricted topology and control entry points to function. More precisely, they rely on the assumption that everyone on one side of the entry point--the firewall--is to be trusted, and that anyone on the other side is, at least potentially, an enemy.

Distributed firewalls are host-resident security software applications that protect the enterprise network's servers and end-user machines against unwanted intrusion. They offer the advantage of filtering traffic from both the Internet and the internal network. This enables them to prevent hacking attacks that originate from both the Internet and the internal network. This is important because the most costly and destructive attacks still originate from within the organization.

They are like personal firewalls except they offer several important advantages like central management, logging, and in some cases, access-control granularity. These features are necessary to implement corporate security policies in larger enterprises. Policies can be defined and pushed out on an enterprise-wide basis.

A feature of distributed firewalls is centralized management. The ability to populate servers and end-users machines, to configure and "push out" consistent security policies helps to maximize limited resources. The ability to gather reports and maintain updates centrally makes distributed security practical. Distributed firewalls help in two ways. Remote end-user machines can be secured. Secondly, they secure critical servers on the network preventing intrusion by malicious code and "jailing" other such code by not letting the protected server be used as a launch pad for expanded attacks.

Usually deployed behind the traditional firewall, they provide a second layer of defense. They work by enabling only essential traffic into the machine they protect, prohibiting other types of traffic to prevent unwanted intrusions. Whereas the perimeter firewall must take a generalist, common denominator approach to protecting servers on the network, distributed firewalls act as specialists.



In today's world, most businesses, regardless of size, believe that access to the Internet is imperative if they are going to compete effectively. Even though the benefits of connecting to the Internet are considerable, so are the risks. When a business connects its private network to the Internet, it is not just providing its employees access to external information and Internet services; it is also providing external users with a means to access the company's own private information. Horror stories abound in the media regarding companies that have had proprietary information stolen, modified, or otherwise compromised by attackers who gained access via the Internet. For this reason, any business that has ever contemplated connecting to the Internet has been forced to deal with the issue of network security.

Figure presents a time line of the major firewall architectures

In response to these risks, a whole industry has formed during the last several years to meet the needs of businesses wanting to take advantage of the benefits of being connected to the Internet while still maintaining the confidentiality, integrity, and availability of their own private information and network resources. This industry revolves around firewall technology.

A firewall provides a single point of defence between two networks—it protects one network from the other. Usually, a firewall protects the company's private network from the public or shared networks to which it is connected. A firewall can be as simple as a router that filters packets or as complex as a multi-computer, multi-router solution that combines packet filtering and application level proxy services.

Firewall technology is a young but quickly maturing industry. The first generation of firewall architectures has been around almost as long as routers, first appearing around 1985 and coming out of Cisco's IOS software division. These firewalls are called packet filter firewalls. However, the first paper describing the screening process used by packet


EVOLUTION OF THE FIREWALL


filter firewalls did not appear until 1988, when Jeff Mogul from Digital Equipment Corporation published his studies.

During the 1989-1990 timeframe, Dave Presotto and Howard Trickey of AT&T Bell Laboratories pioneered the second generation of firewall architectures with their research in circuit relays, which are also known as circuit level firewalls. They also implemented the first working model of the third generation of firewall architectures, known as application layer firewalls. However, they neither published any papers describing this architecture nor released a product based upon their work.

As is often the case in research and development, the third generation of firewall architectures was independently researched and developed by several people across the United States during the late 1980's and early 1990's. Publications by Gene Spafford of Purdue University, Bill Cheswick of AT&T Bell Laboratories, and Marcus Ranum describing application layer firewalls first appeared during 1990 and 1991. Marcus Ranum's work received the most attention in 1991 and took the form of bastion hosts running proxy services. Ranum's work quickly evolved into the first commercial product—Digital Equipment Corporation's SEAL product.

Around 1991, Bill Cheswick and Steve Bellovin began researching dynamic packet filtering and went so far as to help develop an internal product at Bell Laboratories based upon this architecture; however, this product was never released. In 1992, Bob Braden and Annette DeSchon at USC's Information Sciences Institute began independently researching dynamic packet filter firewalls for a system that they called "Visas." Check Point Software released the first commercial product based on this fourth generation architecture in 1994.

During 1996, Scott Wiegel, Chief Scientist at Global Internet Software Group, Inc., began laying out the plans for the fifth generation firewall architecture, the Kernel Proxy architecture. Cisco Centri Firewall, released in 1997, is the first commercial product based on this architecture.



Firewalls come in various sizes and flavors. The most typical idea of a firewall is a dedicated system or appliance that sits in the network and segments an "internal" network from the "external" Internet. Most home or SOHO networks use an appliance-based device for broadband connectivity that includes a built-in firewall. In general, firewalls can be categorized under one of two general types:

• Desktop or personal firewalls• Network firewalls

The primary difference between these two types of firewalls simply boils down to the number of hosts that the firewall protects. Within the network firewall type, there are primary classifications of devices, including the following:

• Packet-filtering firewalls (stateful and nonstateful)• Circuit-level gateways• Application-level gateways

The preceding list describes general classes of firewalls but, as discussed later, many network firewalls represent hybrids of the preceding classifications. Many firewalls have characteristics that place them in more than one classification.

Figure below shows a breakdown of the various firewall types currently available. This figure does not provide complete details of the various capabilities within each firewall type but rather shows the general taxonomy of the different firewalls available in the two primary types: personal/desktop firewalls and network firewalls.


FIREWALL TAXONOMY


Personal firewalls are designed to protect a single host. They can be viewed as a hardened shell around the host system, whether it is a server, desktop, or laptop. Typically, personal firewalls assume that outbound traffic from the system is to be permitted and inbound traffic requires inspection. By default, personal firewalls include various profiles that accommodate the typical traffic a system might see. For example, ZoneAlarm has low, medium, and high settings that allow almost all traffic, selected traffic, or nearly no traffic, respectively, through to the protected system. In a similar vein, IPTableswhich you can set up as a personal firewall as well as in a network firewall roleduring the setup of the Linux system, enables the installer to choose the level of protection for the system and the customization for ports that do not fall into a specific profile.

One important consideration with personal firewalls is centralized management. Some vendors have identified that a significant barrier to deployment of personal firewall on every end system is the need for centralized management so that policies can be developed and applied remotely to end systems and have developed such capabilities within their products. Large enterprises are hesitant to adopt this personal firewall technology for their systems because of the difficulty of maintaining a consistent firewall policy across the enterprise.

Network firewalls are designed to protect whole networks from attack. Network firewalls come in two primary forms: a dedicated appliance or a firewall software suite installed on top of a host operating system. Examples of appliance-based network firewalls include the Cisco PIX, the Cisco ASA, Juniper's NetScreen firewalls, Nokia firewalls, and Symantec's Enterprise Firewall. The more popular software-based firewalls include Check Point's Firewall-1 NG or NGX Firewalls, Microsoft ISA Server, Linux-based IPTables, and BSD's pf packet filter. The Sun Solaris operating system has, in the past, been bundled with Sun's enterprise firewall, SunScreen. With the release of Solaris 10, Sun has begun bundling the open source IP Filter (IPF) firewall as an alternative to SunScreen.

Many network firewalls provide enterprise users the maximum flexibility and protection in a firewall system. These firewalls have over the past few years incorporated many new features such as in-line intrusion detection and prevention as well as virtual private network (VPN) termination capabilities both for LAN-to-LAN VPNs as well as remote-access-user VPNs. Another feature that has been introduced into network firewalls is a deep packet-inspection capability. The firewall can identify traffic requirements not just by looking at Layer 3 and Layer 4 information but by delving all the way into the application data so that the firewall can make decisions as to how to best handle the traffic flow. This evolution in firewall design and capabilities has led to the development of a new firewall product, the integrated firewall, which is covered in more detail in the next section.


Personal Firewalls

Network Firewalls


Packet filters are network devices that filter traffic based on simple packet characteristics. These devices are typically stateless in that they do not keep a table of the connection state of the various traffic flows through them. To allow traffic in both directions, they must be configured to permit return traffic. Simple packet filters include Cisco IOS access lists as well as Linux's ipfwadm facility to name a few. Although these filters provide protection against a wide variety of threats, they are not dynamic enough to be considered true firewalls. Their primary focus is to limit traffic inbound while providing for outbound and established traffic to flow unimpeded. Example shows a simple access list for filtering traffic. This list is based on the network example in Figure below. The access list is applied to the inbound side of the filtering device that connects the LAN to the Internet.

Figure: Simple Access List Sample Network

Example: Simple Access List

access-list 101 permit icmp any 192.168.185.0 0.0.0.255 echo-replyaccess-list 101 permit icmp any 192.168.185.0 0.0.0.255 ttl-exceededaccess-list 101 permit tcp any 192.168.185.0 0.0.0.255 establishedaccess-list 101 permit udp any host 192.168.185.100 eq 53access-list 101 permit udp any eq 123 192.168.185.0 0.0.0.255

Note that inbound return traffic for DNS (53/UDP) and NTP (123/UDP) are explicitly stated toward the end of the filter list, as are Internet Control Message Protocol (ICMP) echo-reply and Time-To-Live (TTL)-exceeded responses. Without these statements, these packets would be blocked even though they are in response to traffic that originated in the protected LAN. Finally, note the following rule:

access-list 101 permit tcp any 192.168.185.0 0.0.0.255 established


Packet Filters

mk:@MSITStore:H:%5Cfirewall%5CFirewall%20Fundamentals%5CFirewall%20Fundamentals.chm::/1587052210/ch02lev1sec3.html#ch02fig02


This rule is required to allow return traffic from any outside system back to the 192.168.185.0/24 subnet as long as the return traffic has the TCP ACK flag set. Packet filters typically do not have any stateful capabilities to inspect outbound traffic and dynamically generate rules permitting the return traffic to an outbound flow. Figure below shows a simple packet-filtering firewall.

Figure: Packet-Filtering Firewall

A distinct firewall that existed for a short period is the Network Address Translation (NAT) firewall.NAT is now a function of a firewall. NAT firewalls automatically provide protection to systems behind the firewall because they only allow connections that originate from the inside of the firewall. The basic purpose of NAT is to multiplex traffic from an internal network and present it to a wider network (that is, the Internet) as though it were coming from a single IP address or a small range on IP addresses. The NAT firewall creates a table in memory that contains information about connections that the firewall has seen. This table maps the addresses of internal systems to an external address. The ability to place an entire network behind a single IP address is based on the mapping of port numbers on the NAT firewall. For example, consider the systems shown in figure below.


NAT Filters




The hosts on the "inside" of the NAT firewall (192.168.1.1 and 192.168.1.2) are both trying to access the web server 10.100.100.44. Host 192.168.1.1 opens up TCP port 3844 and connects to the web server 10.100.100.44 at TCP port 80. Host 192.168.1.2 opens TCP port 4687 and connects to the web server 10.100.100.44 at TCP port 80. The NAT firewall is configured to translate the entire 192.168.1.0/24 network to the single IP address 172.28.230.55. When the firewall sees the outbound connections, it rewrites the IP layer information in the traffic and replaces 192.168.1.1 and 192.168.1.2 with the single IP address 172.28.230.55. Internally, the NAT firewall maintains a table that keeps track of the traffic flows and translates both 192.168.1.1 and 192.168.1.2 to the IP address 172.28.230.55. It does this by means of network sockets that uniquely identify a given connection. For the example shown in above figure, there are two unique sockets: 192.168.1.1:3844 and 192.168.1.2:4687. When this traffic is seen by the firewall, the NAT process replaces the 192.168.1 network addresses with the 172.28.230.55 address.

The last entry in the table shows above what a NAT firewall does when a specific source port is already taken by a previous connection. In this case, the client 192.168.1.1 is attempting to make a second connection to the web server 10.100.100.44. The client opens a connection on TCP port 4687; however, TCP port 4687 on the NAT firewall is already being used by the connection for the client 192.168.1.2. In this case, the NAT firewall changes not only the source IP address but also the source port and keeps that mapping in its translation table.

Circuit-level firewalls work at the session layer of the OSI model and monitor "handshaking" between packets to decide whether the traffic is legitimate. Traffic to a remote computer is modified to make it appear as though it originated from the circuit-level firewall. This modification makes a circuit-level firewall particularly useful in hiding information about a protected network but has the drawback that it does not filter individual packets in a given connection. Figure below shows an example of a circuit-level firewall.


Circuit-level Firewalls



Figure: Circuit-Level Firewall

A proxy firewall acts as an intermediary between two end systems in a similar fashion as a circuit-level gateway. However, in the case of a proxy firewall, the interaction is controlled at the application layer, as shown in figure below. Proxy firewalls operate at the application layer of the connection by forcing both sides of the conversation to conduct the communication through the proxy. It does this by creating and running a process on the firewall that mirrors a service as though it were running on an end system. To support various services, the proxy firewall must have a specific service running for each protocol: a Simple Mail Transport Protocol (SMTP) proxy for e-mail, a File Transfer Protocol (FTP) proxy for file transfers, and a Hypertext Transfer Protocol (HTTP) proxy for web services.

Figure: Proxy Firewall


Proxy Firewalls



Whenever a client wants to connect to a service on the Internet, the packets making up the connection request are processed by the specific proxy service for that protocol before being forwarded to the target system. Packets returning from the server on the Internet are similarly processed by the same proxy service before being forwarded to the internal system. In many proxy firewalls, a generic proxy service can be used by services that do not have a service specifically tailored to their needs. However, not all services can use this generic proxy. If there are no proxy capabilities for a specific service running on the firewall, no connection to outside servers running that service is possible, or the firewall utilizes other technologies such as circuit-level filtering to filter the connection.

Because of their inspection capabilities, proxy firewalls can look much more deeply into the packets of a connection and apply additional rules to determine whether a packet should be forwarded to an internal host. The disadvantages of a proxy firewall can be in their complex configuration as well as their speed. Because the firewalls look deep into the application, they can introduce delay into network connections. Finally, if there is no specific proxy service for a particular network application and it cannot be made to work with a generic proxy service and the firewall cannot perform other methods of filtering, you cannot put that behind the firewall. Most modern firewalls include basic proxy server architecture in their operation by providing some form of proxy capabilities. For example, PIX OS 6 and earlier had the fixup command, and IPF provided an FTP proxy service to handle active FTP connections.

Modern stateful firewalls combine aspects and capabilities of NAT firewalls, circuit-level firewalls, and proxy firewalls into one system. These firewalls filter traffic initially based on packet characteristics like the packet-filtering firewall but also include session checks to make sure that the specific session is allowed. Unlike proxy or circuit-level firewalls, stateful firewalls are typically designed to be more transparent (like their packet-filtering and NAT cousins). However, they include proxy-filtering aspects by inspecting the application layer data as well through the use of specific services.


Stateful Firewalls


Stateful firewalls are more complex than their constituent component firewalls; however, nearly all modern firewalls on the market today are stateful firewalls and represent the baseline for security in today's networks.

Transparent firewalls (also known as bridging firewalls) are not a completely new firewall but rather a subset of stateful firewalls. Whereas nearly all firewalls operate at the IP layer and above, transparent firewalls sit at Layer 2, the data link layer, and monitor Layer 3+ traffic. Additionally, the transparent firewall can apply packet-filtering rules like any other stateful firewall and still appear invisible to the end user. In essence, the transparent firewall acts as a filtering bridge between two network segments. It represents an excellent way of applying a security policy in the middle of a network segment without having to apply a NAT filter. The benefits of a transparent, bridging firewall fall into three general categories:

• Zero configuration• Performance• Stealth

The bridging firewall requires no changes to the underlying network, which is possible simply because the transparent bridging firewall is plugged in-line with the network it is protecting. Because it operates at the data link layer, no IP address changes are required. The firewall can be placed so as to segment a network subnet between low-security and higher-security systems or to protect a single host if necessary.

Because bridging firewalls tend to be simpler than their Layer 3 cousins, they have a lower processing overhead. That lower overhead enables them to provide better performance as well as deeper packet inspection.

Finally, their stealth nature stems directly from the fact that they are Layer 2 devices. The network interfaces of bridging firewalls have no IP addresses (other than the management interface) assigned to them and therefore are invisible to an attacker. The firewall cannot be attacked because, basically, it cannot be reached.

Virtual firewalls are multiple logical firewalls running on a single physical device. This arrangement allows for multiple networks to be protected by a unique firewall running a unique security policy all in one physical appliance. A service provider can provide firewall services for multiple customers, securing and separating their traffic while managing the entire system on one device. Service providers do so by defining separate security domains for each customer with each domain controlled by a separate logical virtual firewall.


Transparent Firewalls

Virtual Firewalls


Conventional firewalls rely on the notions of restricted topology and control entry points to function. More precisely, they rely on the assumption that everyone on one side of the entry point--the firewall--is to be trusted, and that anyone on the other side is, at least potentially, an enemy.

Some problems with the conventional firewalls that lead to Distributed firewalls are as follows.

Due to the increasing line speeds and the more computation intensive protocols that a firewall must support; firewalls tend to become congestion points. This gap between processing and networking speeds is likely to increase, at least for the foreseeable future; while computers (and hence firewalls) are getting faster, the combination of more complex protocols and the tremendous increase in the amount of data that must be passed through the firewall has been and likely will continue to outpace Moore’s Law .

There exist protocols, and new protocols are designed, that are difficult to process at the firewall, because the latter lacks certain knowledge that is readily available at the endpoints. FTP and RealAudio are two such protocols. Although there exist application-level proxies that handle such protocols, such solutions are viewed as architecturally “unclean” and in some cases too invasive.

Likewise, because of the dependence on the network topology, a PF can only enforce a policy on traffic that traverses it. Thus, traffic exchanged among nodes in the protected network cannot be controlled. This gives an attacker that is already an insider or can somehow bypass the firewall complete freedom to act.


PROBLEMS WITH STANDARD FIREWALL


Worse yet, it has become trivial for anyone to establish a new, unauthorized entry point to the network without the administrator’s knowledge and consent. Various forms of tunnels, wireless, and dial-up access methods allow individuals to establish backdoor access that bypasses all the security mechanisms provided by traditional firewalls. While firewalls are in general not intended to guard against misbehavior by insiders, there is a tension between internal needs for more connectivity and the difficulty of satisfying such needs with a centralized firewall.

IPsec is a protocol suite, recently standardized by the IETF, which provides network-layer security services such as packet confidentiality, authentication, data integrity, replay protection, and automated key management.

This is an artifact of firewall deployment: internal traffic that is not seen by the firewall cannot be filtered; as a result, internal users can mount attacks on other users and networks without the firewall being able to intervene.

Large networks today tend to have a large number of entry points (for performance, failover, and other reasons). Furthermore, many sites employ internal firewalls to provide some form of compartmentalization. This makes administration particularly difficult, both from a practical point of view and with regard to policy consistency, since no unified and comprehensive management mechanism exists.

End-to-end encryption can also be a threat to firewalls, as it prevents them from looking at the packet fields necessary to do filtering. Allowing end-to-end encryption through a firewall implies considerable trust to the users on behalf of the administrators.

Finally, there is an increasing need for finer-grained access control which standard firewalls cannot readily accommodate without greatly increasing their complexity and processing requirements.



Distributed firewalls are host-resident security software applications that protect the enterprise network's critical endpoints against unwanted intrusion that is, its servers and end-user machines. In this concept, the security policy is defined centrally and the enforcement of the policy takes place at each endpoint (hosts, routers, etc). Usually deployed behind the traditional firewall, they provide a second layer of protection.

Since all the hosts on the inside are trusted equally, if any of these machines are subverted, they can be used to launch attacks to other hosts, especially to trusted hosts for protocols like rlogin. Thus there is a faithful effort from the industry security organizations to move towards a system which has all the aspects of a desktop firewall but with centralized management like Distributed Firewalls.

Distributed, host-resident firewalls prevent the hacking of both the PC and its use as an entry point into the enterprise network. A compromised PC can make the whole network vulnerable to attacks. The hacker can penetrate the enterprise network uncontested and steal or corrupt corporate assets.


DISTRIBUTED FIREWALL


Distributed firewalls are often kernel-mode applications that sit at the bottom of the OSI stack in the operating system. They filter all traffic regardless of its origin -- the Internet or the internal network. They treat both the Internet and the internal network as "unfriendly". They guard the individual machine in the same way that the perimeter firewall guards the overall network.

Distributed firewalls rest on three notions:

a) A policy language that states what sort of connections are permitted or prohibited,

b) Any of a number of system management tools, such as Microsoft's SMS or ASD, and

c) IPSEC, the network-level encryption mechanism for TCP/IP.

The basic idea is simple. A compiler translates the policy language into some internal format. The system management software distributes this policy file to all hosts that are protected by the firewall. And incoming packets are accepted or rejected by each "inside" host, according to both the policy and the cryptographically-verified identity of each sender.


Basic working


One of the most often used term in case of network security and in particular distributed firewall is policy. It is essential to know about policies. A “security policy” defines the security rules of a system. Without a defined security policy, there is no way to know what access is allowed or disallowed.

A simple example for a firewall is

• Allow all connections to the web server.• Deny all other access.

The distribution of the policy can be different and varies with the implementation. It can be either directly pushed to end systems, or pulled when necessary.

The hosts while booting up, pings to the central management server to check whether the central management server is up and active. It registers with the central management server and requests for its policies which it should implement. The central management server provides the host with its security policies.

For example, a license server or a security clearance server can be asked if a certain communication should be permitted. A conventional firewall could do the same, but it lacks important knowledge about the context of the request. End systems may know things like which files are involved, and what their security levels might be. Such information could be carried over a network protocol, but only by adding complexity.

The push technique is employed when the policies are updated at the central management side by the network administrator and the hosts have to be updated immediately. This push technology ensures that the hosts always have the updated policies at anytime.

The policy language defines which inbound and outbound connections on any component of the network policy domain are allowed, and can affect policy decisions on any layer of the network, being it at rejecting or passing certain packets or enforcing policies at the application layer.


POLICIES

Pull Technique

Push Technique


Many possible policy languages can be used, including file-oriented schemes similar to Firmato, the GUIs that are found on most modern commercial firewalls, and general policy languages such as KeyNote. The exact nature is not crucial, though clearly the

Language must be powerful enough to express the desired policy. A sample is shown in Figure 1.

inside_net = x509{name="*.example.com"}; mail_gw = x509{name="mailgw.example.com"}; time_server = IPv4{10.1.2.3}; allow smtp(*, mail_gw); allow smtp(mail_gw, inside_net); allow ntp(time_server, inside_net); allow *(inside_net, *);

Figure 1: A sample policy configuration file. SMTP from the outside can only reach the machine with a certificate identifying it as the mail gateway; it, in turn, can speak SMTP to all inside machines. NTP--a low-risk protocol that has its own application- level protection--can be distributed from a given IP address to all inside machines. Finally, all outgoing calls are permitted.



What is important is how the inside hosts are identified. Today's firewalls rely on topology; thus, network interfaces are designated "inside", "outside", "DMZ", etc. We abandon this notion, since distributed firewalls are independent of topology.

A second common host designator is IP address. That is, a specified IP address may be fully trusted, able to receive incoming mail from the Internet, etc. Distributed firewalls can use IP addresses for host identification, though with a reduced level of security.

Our preferred identifier is the name in the cryptographic certificate used with IPSEC. Certificates can be a very reliable unique identifier. They are independent of topology; furthermore, ownership of a certificate is not easily spoofed. If a machine is granted certain privileges based on its certificate, those privileges can apply regardless of where the machine is located physically.


IDENTIFIERS


* A central management system for designing the policies.

* A transmission system to transmit these polices.

* Implementation of the designed policies in the client end.

Central Management, a component of distributed firewalls, makes it practical to secure enterprise-wide servers, desktops, laptops, and workstations. Central management provides greater control and efficiency and it decreases the maintenance costs of managing global security installations. This feature addresses the need to maximize network security resources by enabling policies to be centrally configured, deployed, monitored, and updated. From a single workstation, distributed firewalls can be scanned to understand the current operating policy and to determine if updating is required.

The policy distribution scheme should guarantee the integrity of the policy during transfer. The distribution of the policy can be different and varies with the implementation. It can be either directly pushed to end systems, or pulled when necessary.

The security policies transmitted from the central management server have to be implemented by the host. The host end part of the Distributed Firewall does provide any administrative control for the network administrator to control the implementation of policies. The host allows traffic based on the security rules it has implemented.


COMPONENTS OF A DISTRIDUTER FIREWALL

Central management System

Policy Distribution

Host End Implementation


The distributed firewall uses a central policy, but pushes enforcement towards the edges. That is, the policy defines what connectivity, inbound and outbound, is permitted; this policy is distributed to all endpoints, which enforce it.

To implement a distributed firewall, we need a security policy language that can describe which connections are acceptable, an authentication mechanism, and a policy distribution scheme. As a policy specification language, we use the KeyNote trust-management system, further described in Section 7.1.As an authentication mechanism, we decided to use IPsec for traffic protection and user/host authentication. When it comes to policy distribution, we have a number of choices:

We can distribute the KeyNote (or other) credentials to the various end users. The users can then deliver their credentials to the end hosts through the IKE protocol. The users do not have to be online for the policy update; rather, they can periodically retrieve the credentials from a repository (web server). Since the credentials are signed and can be transmitted over an insecure connection, users could retrieve their new credentials even when the old ones have expired.

The credentials can be pushed directly to the end hosts, where they would be immediately available to the policy verifier. Since every host would need a large number, if not all, of the credentials for every user, the storage and transmission bandwidth requirements are higher than in the previous case.

The credentials can be placed in a repository where they can be fetched as needed by the hosts. This requires constant availability of the repository, and may impose some delays in the resolution of request (such as a TCP connection establishment).

While the first case is probably the most attractive from an engineering point of view. Furthermore, some IPsec implementations do not support connection-grained security. Finally, since IPsec is not (yet) in wide use, it is desirable to allow for a policy-based filtering that does not depend on IPsec. Thus, it is necessary to provide a policy resolution mechanism that takes into consideration the connection parameters, the local policies, and any available credentials, and determines whether the connection should be allowed.


IMPLEMENTING A DISTRIDUTER FIREWALL


Trust Management is a relatively new approach to solving the authorization and security policy problem. Making use of public key cryptography for authentication, trust management dispenses with unique names as an indirect means for performing access control. Instead, it uses a direct binding between a public key and a set of authorizations, as represented by a safe programming language. This results in an inherently decentralized authorization system with sufficient expressibility to guarantee flexibility in the face of novel authorization scenarios.

Figure : Application Interactions with KeyNote. The Requester is typically a user that authenticates through some application-dependent protocol, and optionally provides credentials. The Verifier needs to determine whether the Requester is allowed to perform the requested action. It is responsible for providing to KeyNote all the necessary information, the local policy, and any credentials. It is also responsible for acting upon KeyNote’s response.

One instance of a trust-management system is KeyNote. KeyNote provides a simple notation for specifying both local security policies and credentials that can be sent over an untrusted network. Policies and credentials contain predicates that describe the trusted actions permitted by the holders of specific public keys (otherwise known as principals). Signed

Credentials, which serve the role of “certificates,” have the same syntax as policy assertions, but are also signed by the entity delegating the trust

Applications communicate with a “KeyNote evaluator” that interprets KeyNote assertions and returns results to applications, as shown in Figure 1. However, different


KeyNote


hosts and environments may provide a variety of interfaces to the KeyNote evaluator (library, UNIX daemon, kernel service, etc.).

A KeyNote evaluator accepts as input a set of local policy and credential assertions, and a set of attributes, called an “action environment,” that describes a proposed trusted action associated with a set of public keys (the requesting principals). The KeyNote evaluator determines whether proposed actions are consistent with local policy by applying the assertion predicates to the action environment. The KeyNote evaluator can return values other than simply true and false, depending on the application and the action environment definition.

An important concept in KeyNote (and, more generally, in trust management) is “monotonicity”. This simply means that given a set of credentials associated with a request, if there is any subset that would cause the request to be approved then the complete set will also cause the request to be approved. This greatly simplifies both request resolution (even in the presence of conflicts) and credential management. Monotonicity is enforced by the KeyNote language (it is not possible to write non-monotonic policies).

It is worth noting here that although KeyNote uses cryptographic keys as principal identifiers, other types of identifiers may also be used. For example, usernames may be used to identify principals inside a host. In this environment, delegation must be controlled by the operating system (or some implicitly trusted application), similar to the mechanisms used for transferring credentials in UNIX or in capability-based systems.

Also, in the absence of cryptographic authentication, the identifier of the principal requesting an action must be securely established. In the example of a single host, the operating system can provide this information.



KeyNote-Version: 2Authorizer: "POLICY"Licensees: "rsa-hex:1023abcd"Comment: Allow Licensee to connect to local port 23 (telnet) from internal addresses only, or to port 22 (ssh) from anywhere. Since this is a policy, no signature field is required.Conditions: (local_port == "23" && protocol == "tcp" && remote_address > "158.130.006.000" && remote_address < "158.130.007.255) -> "true"; local_port == "22" && protocol == "tcp" -> "true";KeyNote-Version: 2Authorizer: "rsa-hex:1023abcd"Licensees: "dsa-hex:986512a1" || "x509-base64:19abcd02=="Comment: Authorizer delegates SSH connection access to either of the Licensees, if coming from a specific address.Conditions: (remote_address == "139.091.001.001" && local_port == "22") -> "true";Signature: "rsa-md5-hex:f00f5673"

Figure: Example KeyNote Policy and Credential. The local policy allows a particular user (as identified by their public key) connect access to the telnet port by internal addresses, or to the SSH port from any address. That user then delegates to two other users (keys) the right to connect to SSH from one specific address. Note that the first key can effectively delegate at most the same rights it possesses. KeyNote does not allow rights amplification; any delegation acts as refinement.

In our prototype, end hosts (as identified by their IP address) are also considered principals when IPsec is not used to secure communications. This allows local policies or credentials issued by administrative keys to specify policies similar to current packet filtering rules.

In the context of the distributed firewall, KeyNote allows us to use the same, simple language for both policy and credentials. The latter, being signed, may be distributed over an insecure communication channel. In KeyNote, credentials may be considered as an extension, or refinement, of local policy; the union of all policy and credential assertions is the overall network security policy. Alternately, credentials may be viewed as parts of a hypothetical access matrix. End hosts may specify their own security policies, or they may depend exclusively on credentials from the administrator, or do anything in between these two ends of the spectrum. Perhaps of more interest, it is possible to “merge” policies from different administrative entities and process them unambiguously, or to layer them in increasing levels of refinement. This merging can be expressed in the KeyNote language, in the form of intersection (conjunction) and union (disjunction) of the component sub-policies.



Although KeyNote uses a human-readable format and it is indeed possible to write credentials and policies that way, our ultimate goal is to use it as an interoperability-layer language that “ties together” the various applications that need access control services. An administrator would use a higher-level language or GUI to specify correspondingly higher-level policy and then have this compiled to a set of KeyNote credentials. This higher-level language would provide grouping mechanisms and network-specific abstractions that are not present in KeyNote. Using KeyNote as the middle language offers a number of benefits:

It can handle a variety of different applications (since it is application-independent but customizable), allowing for more comprehensive and mixed-level policies (e.g., covering email, active code content, IPsec, etc.).

Provides built-in delegation, thus allowing for decentralized administration. Allows for incremental or localized policy updates (as only the relevant

credentials need to be modified, produced, or revoked).

KeyNote-Version: 2Authorizer: "rsa-hex:1023abcd"Licensees: "IP:158.130.6.141"Conditions: (@remote_port < 1024 && @local_port == 22) -> "true";Signature: "rsa-sha1-hex:bee11984"

Figure : An example credential where an (administrative) key delegates to an IP address. This would allow the specified address to connect to the local SSH port, if the connection is coming from a privileged port. Since the remote host has no way of supplying the credential to the distributed firewall through a security protocol like IPsec, the distributed firewall must search for such credentials or must be provided with them when policy is generated/updated.

Most Of the work is done on Open BSD operating system. OpenBSD provides an attractive platform for developing security applications because of the well-integrated security features and libraries (an IPsec stack, SSL, KeyNote, etc.). However, similar implementations are possible under other operating systems.

System is comprised of three components: a set of kernel extensions, which implement the enforcement mechanisms, a user level daemon process, which implements the distributed firewall policies, and a device driver, which is used for two-way communication between the

kernel and the policy daemon


IMPLEMENTATION


Figure: The Figure shows a graphical representation of the system, with all its components. The core of the enforcement mechanism lives in kernel space and is comprised of the two modified system calls that interest us, connect and accept. The policy specification and processing unit lives in user space inside the policy daemon process. The two units communicate via a loadable pseudo device driver interface. Messages travel from the system call layer to the user level daemon and back using the policy context queue.

For our working prototype we focused our efforts on the control of the TCP connections. Similar principles can be applied to other protocols; for unreliable protocols, some form of reply caching is desirable to improve performance.

In the UNIX operating system users create outgoing and allow incoming TCP connections using connect and accept system calls respectively. Since any user has access to these system calls, some “filtering” mechanism is needed. This filtering should be based on a policy that is set by the administrator. Filters can be implemented either in user space or inside the kernel. Each has its advantages and disadvantages.

A user level approach, as depicted in Figure below, requires each application of interest to be linked with a library that provides the required security mechanisms, e.g., a modified libc. This has the advantage of operating system-independence, and thus does not require any changes to the kernel code. However, such a scheme does not guarantee that the applications will use the modified library, potentially leading to a major security problem.


Kernel Extensions


Figure: Wrappers for filtering the connect and accept system calls are added to a system library. While this approach offers considerable flexibility, it suffers from its inability to guarantee the enforcement of security policies, as applications might not link with the appropriate library.

A kernel level approach, as shown in the left side of Figure , requires modifications to the operating system kernel. This restricts us to open source operating systems like BSD and Linux. The main advantage of this approach is that the additional security mechanisms can be enforced transparently on the applications.

As we mentioned previously, the two system calls we need to filter are connect and accept. When connect is issued by a user application and the call traps into the kernel, we create what we call a policy context (see Figure), associated with that connection.

The policy context is a container for all the information related to that specific connection. We associate a sequence number to each such context and then we start filling it with all the information the policy daemon will need to decide whether to permit it or not. In the case of the connect, this includes the ID of the user that initiated the connection, the destination address and port, etc.

Any credentials acquired through IPsec may also be added to the context at this stage. There is no limit as to the kind or amount of information we can associate with a context. We can, for example, include the time of day or the number of other open connections of that user, if we want them to be considered by our decision–making strategy.

Once all the information is in place, we commit that context. The commit operation adds the context to the list of contexts the policy daemon needs to handle. After this, the application is blocked waiting for the policy daemon reply.

Accepting a connection works in a similar fashion. When accept enters the kernel, it blocks until an incoming connection request arrives. Upon receipt, we allocate a new context which we fill in similarly to the connect case. The only difference is that we now also include the source address and port. The context is then enqueued, and the process blocks waiting for a reply from the policy daemon.



typedef struct policy_mbuf policy_mbuf;struct policy_mbuf {policy_mbuf *next;int length;char data[POLICY_DATA_SIZE];};typedef struct policy_context policy_context;struct policy_context {policy_mbuf *p_mbuf;u_int32_t sequence;char *reply;policy_context *policy_context_next;};policy_context *policy_create_context(void);void policy_destroy_context(policy_context *);void policy_commit_context(policy_context *);void policy_add_int(policy_context *, char *, int);void policy_add_string(policy_context *, char *, char *);void policy_add_ipv4addr(policy_context *, char *, in_addr_t *);

Figure 6: The connect(2) and accept(2) system calls create contexts which contain information relevant to that connection. These are appended to a queue from which the policy daemon will receive and process them. The policy daemon will then return to the kernel a decision on whether to accept or deny the connection.

In the next section we discuss how messages are passed between the kernel and the policy daemon.

To maximize the flexibility of our system and allow for easy experimentation, we decided to make the policy daemon a user level process. To support this architecture, we implemented a pseudo device driver, /dev/policy that serves as a communication path between the user–space policy daemon, and the modified system calls in the kernel.

Our device driver supports the usual operations (open, close, read, write, and ioctl). Furthermore, we have implemented the device driver as a loadable module. This increases the functionality of our system even more, since we can add functionality dynamically, without needing to recompile the whole kernel.

If no policy daemon has opened /dev/policy, no connection filtering is done. Opening the device activates the distributed firewall and initializes data structures. All subsequent connect and accept calls will go through the procedure described in the previous section. Closing the device will free any allocated resources and disable the distributed firewall.


Policy Device


When reading from the device the policy daemon blocks until there are requests to be served. The policy daemon handles the policy resolution messages from the kernel, and writes back a reply. The write is responsible for returning the policy daemons decision to the blocked connection call, and then waking it up.

It should be noted that both the device and the associated messaging protocol are not tied to any particular type of application, and may in fact be used without any modifications by other kernel components that require similar security policy handling.

Finally, we have included an ioctl call for “house–keeping”. This allows the kernel and the policy daemon to re–synchronize in case of any errors in creating or parsing the request messages, by discarding the current policy context and dropping the associated connection.

The third and last component of our system is the policy daemon. It is a user level process responsible for making decisions, based on policies that are specified by some administrator and credentials retrieved remotely or provided by the kernel, on whether to allow or deny connections. Policies, as shown in Figure 2, are initially read in from a file. It is possible to remove old policies and add new ones dynamically. In the current implementation, such policy changes only affect new connections.

Communication between the policy daemon and the kernel is possible, using the policy device. The daemon receives each request (see Figure 7) from the kernel by reading the device. The request contains all the information relevant to that connection. Processing of the request is done by the daemon using the KeyNote library, and a decision to accept or deny it is reached. Finally the daemon writes the reply back to the kernel and waits for the next request. While the information received in a particular message is application-dependent, the daemon itself has no awareness of the specific application.

When using a remote repository server, the daemon can fetch a credential based on the ID of the user associated with a connection, or with the local or remote IP address. A very simple approach to that is fetching the credentials via HTTP from a remote web server. The credentials are stored by user ID and IP address, and provided to anyone requesting them. If credential “privacy” is a requirement, one could secure this connection using IPsec or SSL. To avoid potential deadlocks, the policy daemon is not subject to the connection filtering mechanism.


Policy Daemon


u_int32_t seq; /* Sequence Number */u_int32_t uid; /* User Id */u_int32_t N; /* Number of Fields */u_int32_t l[N]; /* Lengths of Fields */char *field[N]; /* Fields */Figure 7: The request to the policy daemon is comprised of the following fields: a sequence number uniquely identifying the request, the ID of the user the connection request belongs to, the number of information fields that will be included in the request, the lengths of those fields, and finally the fields themselves.

To better explain the interaction of the various components in the distributed firewall, we discuss the course of events during two incoming TCP connection requests, one of which is IPsec–protected. The local host where the connection is coming is part of a distributed firewall, and has a local policy as shown in Figure 8.

KeyNote-Version: 2Authorizer: "POLICY"Licensees: ADMINISTRATIVE_KEY

Figure 8: End-host local security policy. In our particular scenario, the policy simply states that some administrative key will specify our policy, in the form of one or more credentials. The lack of a Conditions field means that there are no restrictions imposed on the policies specified by the administrative key.

In the case of a connection coming in over IPsec, the remote user or host will have established an IPsec Security Association with the local host using IKE. As part of the IKE exchange, a KeyNote credential as shown in Figure 9 is provided to the local host. Once the TCP connection is received, the kernel will construct the appropriate context. This context will contain the local and remote IP addresses and ports for the connection, the fact that the connection is protected by IPsec, the time of day, etc.

This information along with the credential acquired via IPsec will be passed to the policy daemon. The policy daemon will perform a KeyNote evaluation using the local policy and the credential, and will determine whether the connection is authorized or not. In our case, the positive response will be sent back to the kernel, which will then permit the TCP connection to proceed. Note that more credentials may be provided during the IKE negotiation (for example, a chain of credentials delegating authority).

If KeyNote does not authorize the connection, the policy daemon will try to acquire relevant credentials by contacting a remote server where these are stored. In our current


EXAMPLE SENARIO


implementation, we use a web server as the credential repository. In a large-scale network, a distributed/replicated database could be used instead.

The policy daemon uses the public key of the remote user (when it is known, i.e., when IPsec is in use) and the IP address of the remote host as the keys to lookup credentials with; more specifically, credentials where the user’s public key or the remote host’s address appears in the Licensees field are retrieved and cached locally (Figure 3 lists an example credential that refers to an IP address). These are then used in conjunction with the information provided by the kernel to re-examine the request. If it is again denied, the connection is ultimately denied.

KeyNote-Version: 2Authorizer: ADMINISTRATIVE_KEYLicensees: USER_KEYConditions:(app_domain == "IPsec policy" && encryption_algorithm == "3DES" && local_address == "158.130.006.141")-> "true"; (app_domain =="Distributed Firewall" && @local_port == 23 && encrypted == "yes" && authenticated == "yes") -> "true";Signature: ...

Figure 9: A credential from the administrator to some user, authorizing that user to establish an IPsec Security Association (SA) with the local host and to connect to port 23 (telnet) over that SA. To do this, we use the fact that multiple expressions can be included in a single KeyNote credential. Since IPsec also enforces some form of access control on packets, we could simplify the overall architecture by skipping the security check for TCP connections coming over an IPsec tunnel. In that case, we could simply merge the two clauses (the IPsec policy clause could specify that the specific user may talk to TCP port 23 only over that SA).


THREAD COMPARISON


Distributed firewalls have both strengths and weaknesses when compared to conventional firewalls. By far the biggest difference, of course, is their reliance on topology. If your topology does not permit reliance on traditional firewall techniques, there is little choice. A more interesting question is how the two types compare in a closed, single-entry network. That is, if either will work, is there a reason to choose one over the other?

Both types of firewalls are excellent at rejecting connection requests for inappropriate services. Conventional firewalls drop the requests at the border; distributed firewalls do so at the host. A more interesting question is what is noticed by the host attempting to connect. Today, such packets are typically discarded, with no notification. A distributed firewall may choose to discard the packet, under the assumption that its legal peers know to use IPSEC; alternatively, it may instead send back a response requesting that the connection be authenticated, which in turn gives notice of the existence of the host.

Firewalls built on pure packet filters cannot reject some "stealth scans" very well. One technique, for example, uses fragmented packets that can pass through unexamined because the port numbers aren't present in the first fragment. A distributed firewall will reassemble the packet and then reject it. On balance, against this sort of threat the two firewall types are at least comparable.

Some services require an application-level proxy. Conventional firewalls often have an edge here; the filtering code is complex and not generally available on host platforms. As noted, a hybrid technique can often be used to overcome this disadvantage.

In some cases, of course, application-level controls can avoid the problem entirely. If the security administrator can configure all Web browsers to reject ActiveX, there is no need to filter incoming HTML via a proxy.

In other cases, a suitably sophisticated IPSEC implementation will suffice. For example, there may be no need to use a proxy that scans outbound FTP control messages for PORT commands, if the kernel will permit an application that has opened an outbound connection to receive inbound connections. This is more or less what such a proxy would do.

A more serious issue concerns inadvertent errors when using application-level policies. An administrator might distribute configuration restrictions for Netscape Navigator or Microsoft's Internet Explorer. But what would happen if a user, in all innocence, were to install the Opera browser? The only real solution here is a standardized way to express application-level policies across all applications of a given type. We do not see that happening any time soon.


Application-level Proxies

Service Exposure and Port Scanning


There is a variety of DOS attacks, and not all can be handled by either concept of firewall systems. Although there can be made no restrictive assumptions about the overall network topology it is most likely that a set of hosts inside the network policy domain will be located physically near to each other and thus use the same connection to the untrusted network. Neither a conventional firewall, nor a distributed one can prevent DOS attacks on the networks perimeter efficiently, although we could emphasize the intentional spread of mission critical hosts on physically separated networks to make such an attack more difficult to an adversary. On the other side, distributed firewalls can behave quite well on DOS attacks which depend on IP spoofing mechanisms, given the assumption that the authorization mechanisms do not rely on IP addresses as credentials. On contrary, with the use trusted repository for either credentials, policies or both, it should be clear that the network devices employing these mechanisms will be subject to extensive attacks, given the overall dependence of end points on its availability.

The "smurf" attack primarily consumes the bandwidth on the access line from an ISP to the target site. Neither form of firewall offers an effective defense. If one is willing to change the topology, both can be moderately effective. Conventional firewalls can be located at the ISP's POP, thus blocking the attack before it reaches the low-bandwidth access line. Distributed firewalls permit hosts to be connected via many different access lines, thus finessing the problem.

It may be possible to chew up CPU time by bombarding the IKE process with bogus security association negotiation requests. While this can affect conventional firewalls, inside machines would still be able to communicate. Distributed firewalls rely much more on IKE, and hence are more susceptible.

Conversely, any attack that consumes resources on conventional firewalls, such as many email attachments that must be scanned for viruses, can bog down such firewalls and affect all users. For that matter, too much legitimate traffic can overload a firewall. As noted, distributed firewalls do not suffer from this effect.

Reliance on network addresses is not a favored concept. Using cryptographic mechanisms most likely prevents attacks based on forged source addresses, under the assumption that the trusted repository containing all necessary credentials has not been subject to compromise in itself. These problems can be solved by conventional firewalls with corresponding rules for discarding packets at the network perimeter but will not prevent such attacks originating from inside the network policy domain.


Denial of Service

IP spoofing

Malicious software


With the spread use of distributed object-oriented systems like CORBA, client-side use of Java and weaknesses in mail readers and the like there is a wide variety of threats residing in the application and intermediate level of communication traffic. Firewall mechanisms at the perimeter can come useful by inspecting incoming emails for known malicious code fingerprints, but can be confronted with complex, thus resource-consuming situations when making decisions on other code, like Java.

Using the framework of a distributed firewall and especially considering a policy language which allows for policy decision on the application level can circumvent some of these problems, under the condition that contents of such communication packets can be interpreted semantically by the policy verifying mechanisms. Stateful inspection of packets shows up to be easily adapted to these requirements and allows for finer granularity in decision making. Furthermore malicious code contents may be completely disguised to the screening unit at the network perimeter, given the use of virtual private networks and enciphered communication traffic in general and can completely disable such policy enforcement on conventional firewalls.

Many firewalls detect attempted intrusions. If that functionality is to be provided by a distributed firewall, each individual host has to notice probes and forward them to some central location for processing and correlation.

The former problem is not hard; many hosts already log such attempts. One can make a good case that such detection should be done in any event. Collection is more problematic, especially at times of poor connectivity to the central site. There is also the risk of coordinated attacks in effect causing a denial of service attack against the central machine.

Our tentative conclusion is that intrusion detection is somewhat harder than with conventional firewalls. While more information can be gathered, using the same techniques on hosts protected by conventional firewalls would gather the same sort of data.

Given the natural view of a conventional firewall on the networks topology as consisting of an inside and outside, problems can arise, once one or more members of the policy network domain have been compromised. Perimeter firewalls can only enforce policies between distinct networks and show no option to circumvent problems which arise in the situation discussed above.

Given a distributed firewalls independence on topological constraints supports the enforcement of policies whether hosts are members or outsiders of the overall policy domain and base their decisions on authenticating mechanisms which are not inherent


Intrusion Detection

Insider Attacks

SENARIO


characteristics of the networks layout. Moreover, compromise of an endpoint either by an legitimate user or intruder will not weaken the overall network in a way that leads directly to compromise of other machines, given the fact that the deployment of virtual private networks prevents sniffing of communication traffic in which the attacked machine is not involved.

On the other side, on the end-point itself nearly the same problems arise as in conventional firewalls: Assuming that a machine has been taken over by an adversary must lead to the conclusion that the policy enforcement mechanisms them self may be broken. The installation of backdoors on this machine can be done quite easily once the security mechanisms are flawed and in the lack of a perimeter firewall, there is no trusted entity anymore which might prevent arbitrary traffic entering or leaving the compromised host.

Additionally use of tools like SSH and the like allow tunneling of other applications communication and can not be prevented without proper knowledge of the decrypting credentials, moreover given the fact that in case an attack has shown up successfully the verifying mechanisms in them self may not be trusted anymore.

At first glance, the biggest weakness of distributed firewalls is their greater susceptibility to lack of cooperation by users. What happens if someone changes the policy files on their own?

Distributed firewalls can reduce the threat of actual attacks by insiders, simply by making it easier to set up smaller groups of users. Thus, one can restrict access to a file server to only those users who need it, rather than letting anyone inside the company pound on it.

It is also worth expending some effort to prevent casual subversion of policies. If policies are stored in a simple ASCII file, a user wishing to, for example, play a game could easily turn off protection. Requiring the would-be uncooperative user to go to more trouble is probably worthwhile, even if the mechanism is theoretically insufficient.

For example, policies could be digitally signed, and verified by a frequently-changing key in an awkward-to-replace location. For more stringent protections, the policy enforcement can be incorporated into a tamper-resistant network card.


CONCLUSION


Network security policy specification remains under the control of the network administrator in distributed firewall network system. Its enforcement, however, is left up to the hosts in the protected network. Security policy is specified using KeyNote policies and credentials, and is distributed to the users and hosts in the network. Since enforcement occurs at the endpoints, various shortcomings of traditional firewalls are overcome:

Security is no longer dependent on restricting the network topology. This allows considerable flexibility in defining the “security perimeter,” which can easily be extended to safely include remote hosts and networks (e.g., telecommuters, extranets).

Since we no longer solely depend on a single firewall for protection, we eliminate a performance bottleneck. Alternately, the burden placed on the traditional firewall is lessened significantly, since it delegates a lot of the filtering to the end hosts.

Filtering of certain protocols (e.g., FTP) which was difficult when done on a traditional firewall, becomes significantly easier, since all the relevant information is present at the decision point, i.e., the end host.

The number of outside connections the protected network is no longer a cause for administration nightmares. Adding or removing links has no impact on the security of the network. “Backdoor” connections set up by users, either intentionally or inadvertently, also do not create windows of vulnerability.

Insiders may no longer be treated as unconditionally trusted. Network compartmentalization becomes significantly easier.

End-to-end encryption is made possible without sacrificing security, as was the case with traditional firewalls. In fact, end-to-end encryption greatly improves the security of the distributed firewall.

Application-specific policies may be made available to end applications over the same distribution channel.

Filtering (and other policy) rules are distributed and established on an as-needed basis; that is, only the hosts that actually need to communicate need to determine what the relevant policy with regard to each other is. This significantly eases the task of policy updating, and does not require each host/firewall to maintain the complete set of policies, which may be very large for large networks. Furthermore, policies and their distribution scales much better with respect to the network size and user base than a more tightly-coupled and synchronized approach would.

On the other hand, distributed firewall architecture requires high quality administration tools. Also, note that the introduction of a distributed firewall infrastructure in a network does not completely eliminate the need for a traditional firewall. The latter is still useful in certain tasks:

It is easier to counter infrastructure attacks that operate at a level lower than the distributed firewall. Note that this is mostly an implementation issue; there is no reason why a distributed firewall cannot operate at arbitrarily low layers, other than potential performance degradation.



Denial-of-service attack mitigation is more effective at the network ingress points (depending on the particular kind of attack).

Intrusion detection systems are more effective when located at a traditional firewall, where complete traffic information is available.

The traditional firewall may protect end hosts that do not (or cannot) support the distributed firewall mechanisms. Integration with the policy specification and distribution mechanisms is especially important here, to avoid duplicated filters and windows of vulnerability.

Finally, a traditional firewall may simply act as a fail-safe security mechanism.

Since most of the security enforcement has been moved to the end hosts, the task of a traditional firewall operating in a distributed firewall infrastructure is significantly eased.

A final point is that, from an administrative point of view, fully distributed firewall architecture is very similar to a network with a large number of internal firewalls.


FUTURE WORK


There are a number of possible extensions that be done in the process of building a more general and complete system. The future work can be done on these points.

• High quality administration tools NEED to exist for distributed firewalls to be

accepted.

• Allow per-packet scanning as opposed to per-connection scanning

• Policy updating and revocation

• Credential discovery



1. Sonnenreich, Wes, and Tom Yates, Building Linux and OpenBSD Firewalls, Singapore: Addison Wiley

2. Zwicky, D. Elizabeth, Simon Cooper, Brent D. Chapman, Building Internet Firewalls O'Reilly Publications

3. Wes Noonan and Ido Dubrwasky, Firewall Fundamentals, Pearson Education

1. Bellovin, M. Steven “Distributed Firewalls", login, November 1999, pp. 39-47 http://www.research.att.com/~smb/papers/distfw.html

2. Dr. Hancock, Bill "Host-Resident Firewalls: Defending Windows NT/2000 Servers and Desktops from Network Attacks"

3. Bellovin, S.M. and W.R. Cheswick, "Firewalls and Internet Security: Repelling the Wily Hacker", Addison-Wesley, 1994.

4. Ioannidis, S. and Keromytis, A.D., and Bellovin, S.M. and J.M. Smith, "Implementing a Distributed Firewall", Proceedings of Computer and Communications Security (CCS), pp. 190-199, November 2000, Athens, Greece.

And several URLs.


REFERENCES

Books

White Papers and Reports

introduction - latest seminar topics for … seminar report on distributed firewall 09203005 a...

Documents