inweld alambre 70s6.pdf

1
Inweld 70S-6 Alloy 70S-6 UNS K11040 AWS A5.18 ER70S-6 ASME SFA5.18 ER70S-6 MIL-E-23765/1: MIL-70S-6 Description and Applications Inweld 70S-6 contains higher levels of manganese and silicon than many other classifications of mild steel wires. The increased Mn and Si content gives stronger deoxidizing power when welding over mild or carbon steel that may have traces of rust or mill scale such as found on structural and plate steels. Inweld 70S-6 is used for single or multi-pass welding. An excellent choice for sheet metal applications, where the higher silicon content creates excellent “wetting out” properties and produces weld deposits that are essentially flat to slightly convex and require little or no grinding. Weld deposits are x-ray quality. Chemical Composition range of Inweld ER70S-6 C Mn Si P S Ni Cr Mo V Cu 0.06-0.15 1.40-1.85 0.80-1.15 0.025 0.035 0.15 0.15 0.15 0.03 0.50 Single values are maximum unless otherwise specified. Average As-Welded Brinell Hardness: NA 160 Tensile Strength: 70,000 psi (482 MPa) 85,000 psi (586 MPa) Yield Strength: 58,000 psi (399 MPa) 70,000 psi (482 MPa) Elongation in 2”: 22% 28% Charpy V-Notch at -20°F: 20 ft./lbs. 40 ft./lbs. Recommended Welding Parameters GMAW (DCEP - Electrode+) 100% CO or a 75-25% Argon/CO Mixture 98% Argon / 2% O Mixture Wire Diameter 0.023” 0.030” 0.035” 0.045” 0.035” 0.045” 1/16” Voltage 14-19 15-20 16-25 18-23 23-26 23-29 25-31 Amperage 30-85 40-130 60-235 90-290 160-300 170-375 275-475 GTAW (DCEN - Electrode-) 100% Ar 2% Thoriated, or 1.5% Lanthanum Tungsten Electrode 1/16” 3/32” 1/8” 12 12 12 100-160 120-250 150-300 2 2 2 Spray AWS Requirement Inweld 70S-6 Available Packaging: 36” Cut Lengths: 0.030”-3/16” 33/44 lb. (12”) Spools: 0.023”-1/16” 2 lb. (4”) Spools: 0.023”-0.045” 550 lb. Pail Pack Drums: 0.035” and 0.045” 11 lb. (8”) Spools: 0.023”-0.045” 1029 South Marietta Street Gastonia, NC 28054 1.800.924.4092 1216 Illinois Avenue South Houston, TX 77587 1.800.338-4239 3962 Portland Street Coplay, PA 18037 1.800.346.5368 www.inweldcorporation.com Pennsylvania North Carolina Texas Welding Alloys & Supplies

Upload: rodrigo-martinez

Post on 07-Nov-2015

15 views

Category:

Documents


3 download

TRANSCRIPT

  • Inweld70S-6

    Alloy 70S-6 UNS K11040AWS A5.18 ER70S-6ASME SFA5.18 ER70S-6MIL-E-23765/1: MIL-70S-6

    Description and ApplicationsInweld 70S-6 contains higher levels of manganese and silicon than many other classifications of mild steel wires. The increased Mn and Si content gives stronger deoxidizing power when welding over mild or carbon steel that may have traces of rust or mill scale such as found on structural and plate steels.

    Inweld 70S-6 is used for single or multi-pass welding. An excellent choice for sheet metal applications, where the higher silicon content creates excellent wetting out properties and produces weld deposits that are essentially flat to slightly convex and require little or no grinding. Weld deposits are x-ray quality.

    Chemical Composition range of Inweld ER70S-6 C Mn Si P S Ni Cr Mo V Cu

    0.06-0.15 1.40-1.85 0.80-1.15 0.025 0.035 0.15 0.15 0.15 0.03 0.50

    Single values are maximum unless otherwise specified.

    Average As-Welded Brinell Hardness: NA 160Tensile Strength: 70,000 psi (482 MPa) 85,000 psi (586 MPa)Yield Strength: 58,000 psi (399 MPa) 70,000 psi (482 MPa)Elongation in 2: 22% 28%Charpy V-Notch at -20F: 20 ft./lbs. 40 ft./lbs.

    Recommended Welding ParametersGMAW (DCEP - Electrode+)100% CO or a 75-25% Argon/CO Mixture98% Argon / 2% O Mixture

    Wire Diameter0.0230.0300.0350.0450.0350.0451/16

    Voltage14-1915-2016-2518-2323-2623-2925-31

    Amperage30-85

    40-13060-23590-290

    160-300170-375275-475

    GTAW (DCEN - Electrode-)100% Ar2% Thoriated, or 1.5% Lanthanum Tungsten Electrode

    1/163/321/8

    121212

    100-160120-250150-300

    22

    2

    Spray

    AWS Requirement Inweld 70S-6

    Available Packaging:36 Cut Lengths: 0.030-3/16 33/44 lb. (12) Spools: 0.023-1/162 lb. (4) Spools: 0.023-0.045 550 lb. Pail Pack Drums: 0.035 and 0.04511 lb. (8) Spools: 0.023-0.045

    1029 South Marietta StreetGastonia, NC 28054

    1.800.924.4092

    1216 Illinois AvenueSouth Houston, TX 77587

    1.800.338-4239

    3962 Portland StreetCoplay, PA 18037

    1.800.346.5368w w w . i n w e l d c o r p o r a t i o n . c o m

    Pennsylvania North Carolina Texas

    Welding Alloys & Supplies