ips1000 for tmic project.10

7/27/2019 IPS1000 for TMIC Project.10

1/20

HUAWEI TECHNOLOGIES CO., LTD.

www.huawei.com

Huawei Confidential

Security Level:2009-8-15

IPS1000 Power Distribution

Installation and Connection(For TMIC project P02)


2/20

HUAWEI TECHNOLOGIES CO., LTD. Page 2Huawei Confidential

BMU

ATS

ACDB

IPS1000

INTERNAL FUNCTION OF IPS1000:


3/20


Work Principle of 1+0 Energy System

D.G Starts to

powers the BTS

and charges the

Battery

D.G. stops and

Battery discharges

to power the BTS

About 6hrs

Battery is

fully charged

Battery discharges to

a setting residualcapacity(40%)

Depended on the consumptionof the site and batterys age.

Remark: For some 1+0 sites which have EDC, the site will use the EDC first , if the EDC is off , the DG and battery wil l cycle

like the sites which have no EDC, anytime the EDC is available, the system will switch to EDC to supply for the site.


4/20


SITE POWER CONNECTION CHART FOR OUTDOOR GREEN FIELD:

Power cableAlarm cable

ACDB Guard Room

Lighting

SocketBY CIVIL WORK SUB-CON

IPS1000

BTS

Battery (-48V)

(Mini shelter)

TE

equipment

Gen-set

Mains

(DG2)

optional

Done by CW Sub-con

Done by TE Sub-con

Done by DG Supplier


5/20


DGS BATTERY CABLEDG START SIGNAL

CABLE

DGS POWER CABLE

EDCSee next for the connection

DETAIL CONNECTION FOR IPS

ACDB

L1 L2 L3 N

From IPS


6/20


+

-

Current transformer DC power connection at APM30

Alarm connector

for Mini shelterFrom Mini sheltersdoor fan

From Temperature

sensor in Mini shelter

Connect to Batt. temp

in APM30

From Door sensor of

Mini shelter

Connect to APM30

door sensor

(see next page)

1

2

3

4

5

67

98

1110

12

Mini Shelter

SETAIL CONNECTION OF MINI SHELTER AND IPS


7/20


Take this short connector out and connect

the door alarm cable from Mini shelter

BTS

CONTROL CONNECTION AT IPS

(Done by DG supplier)

M G + -

From Current transformer

(at min i shelter)

-48V

PGND

To DG start

To DG Battery

+ -

BMU Fail SPD Fail

(To APM30H)

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26

To mini shelter

Bus bar


8/20


DG Installation(1.2)---EDC AC Power Cable


9/20

Instruction to change the AC power input from 1 to 3 phases


10/20


N

L1

L2

L3From

ACDB

Take this out from the connector board

APM30 Panel

AC power input

connector

Instruction to change the AC power input from 1 to 3 phases

supply for Green field BTS outdoor site


11/20


Battery Cabinet Installation(1)---Summay

Chart


12/20


Battery Cabinet Installation(3)---

Connection Between Battery and

IPS/Power System

Power System Battery Input PortIPS

RTN -48V

Fan Power Input

M G

1-2


13/20


Battery Cabinet Installation(2)---Install Current

Sensor

! Make sure the connector is faced down to the floorotherwise the current transformer doesnt work.


14/20


DG Alarm Connection for (1+1) site

APM30H

LOW FUELGEN2 RUNGEN2 FAULT

GEN1 RUN

GEN1 FAULT

1..81

.

.

.

.

8

1..8

1

.

.

.

.

8

APM30H


15/20


APM30H

BMU FAIL

GEN1 RUN

GEN1 FAULT

1..8

1

.

.

.

.

8

APM30H

LOW FUEL

DG Alarm Connection for (1+0) site

BMU Fail

IPS SET(2)


16/20


IPS SET(2)

Note: During the commissioning, we only set:

1. Batteries capacity (as the installed batteries)

2. The date and t ime

IPS St t U


17/20


When the power supply is coming the RUN led is blinked, if

the power reached the terminals but the RUN light not

ON:

1. Check Switch (1) toAuto or not if not switch it toAuto

2. Check the fuses (2) whether they are loose or not

properly connected (take it out and check then put it inagain and check the RUN light if the light is OK wait

about 10s the transfer switch will ON then the light on

the front door is ON).

1

3

Set to 0000 if site (1+0) means

DG+Battery

Power Indicator (front door)

IPS Start Up

Instruction


18/20


IPS SET(3)

1Set the power switch of the BMU to OFF, disconnect the EDC

inputif EDC is available, set the diesel generator to the

automatic mode, then the diesel generator will start automatically.

2Set the power switch of the BMU to ON, set the diesel

generator to the Test Mode, selectATS Control, press the ENT

button of control panel, select Close and press ENT button to

stop the diesel generator.

3Exit the Test Mode and the diesel generator will start to supplypower 3 automatically.

4Connect the EDC inputif EDC is available, the IPS will

start the EDC to supply power and the diesel generator will stop

work a moment later automatically.5After the test, close the door of each cabinet and give the key

to the person in charge for proper management.


19/20


Accessories for IPS1000 (in the box)

CT sensor

Fire proofing Mud (use to close the hole of PG

socket after finishing the installation)

Control cables terminals

Grounding Terminal

(Note: dont forget to

connect this cable)

All the accessories in IPS1000s box


20/20

Thank youwww.huawei.com

ips1000 for tmic project.10

Documents