Disclosure to Promote the Right To Information

Whereas the Parliament of India has set out to provide a practical regime of right to information for citizens to secure access to information under the control of public authorities, in order to promote transparency and accountability in the working of every public authority, and whereas the attached publication of the Bureau of Indian Standards is of particular interest to the public, particularly disadvantaged communities and those engaged in the pursuit of education and knowledge, the attached public safety standard is made available to promote the timely dissemination of this information in an accurate manner to the public.

इंटरनेट मानक

“!ान $ एक न' भारत का +नम-ण”Satyanarayan Gangaram Pitroda

“Invent a New India Using Knowledge”

“प0रा1 को छोड न' 5 तरफ”Jawaharlal Nehru

“Step Out From the Old to the New”

“जान1 का अ+धकार, जी1 का अ+धकार”Mazdoor Kisan Shakti Sangathan

“The Right to Information, The Right to Live”

“!ान एक ऐसा खजाना > जो कभी च0राया नहB जा सकता है”Bhartṛhari—Nītiśatakam

“Knowledge is such a treasure which cannot be stolen”

“Invent a New India Using Knowledge”

है”ह”ह

IS 10282 (1982): Cage Wheel for Power Tillers [FAD 11:Agricultural Tractors and Power Tillers]

( Reaffirmed2004)

IS : 1021Z ..1912

Indian StandardSPECIFICATION FOR

CAGE \VHEEL FOR POWER TILLERS

B

@ Cf/!fti,., 1983

INDI4N STAKDAaDS INSTITUTION).LUlAK altAYAN. , BAHADU1t SHAll ZAP",a MARC

N1W DILHI '100Gt

IS I 10282 • 1982

Indian StandardSPECIFICATION FOR

CAGE WHEEL FOR POWER TILLERS

Agricultural Tractors and Power Tillers SectionalCommittee, AFDC 52

ChairmanPRO)' M. M. M1J;llTA

R~prtuntiflg

Escorts Limited, Faridabad

Research,Indian Council of AgriculturalNew Delhi

Escorts 'Tractors Limited, Faridabad

MtmberJ

SIUU A. K. RAMAN ( Alt#f'nate toProf M. M. Mehta)

DR A. AL.A.M.

SnRI A. V. AJ.BXANDKR

SRRI K. P. J AIM' ( Alltrnat#)SaRI S. S. BAllHULKAR Kirloskar Tractors Limited, Naaik

Suur S. V. DI~SHPANDEY ( Alternat,)SURI BIIUPENVltA National Agricultural Co-operative Marketing

Federation of India Limited, New DelhiSHRI Y. K.JAIN (Alternate)

SURI CHANDRA MOHAN Punjab Tractors Limited, RoparSHRI G. S. RIHA.r, (Allernal6 I )SURt S. S. GREWAL ( Alterrwte I I )

SHRI C. B. CHUQH Indian Jnvestrnenr Centre, New DelhiSHRI M. R. DEWAN Tractor Training and Testing Station ( Ministry

of Agriculture), I3udniSURI J. Pn A~A n ( Alternate I )SlIRt R. S. DASS (.tlt~rnate II )

DrRlr<OTOR Central Inaritute of Agricultural Engineering( 1CAR), Bhopal

Harsha T'ractors Limited, GhaziahadDrrer t or.rte Genera! of Tt-chnical Development

( Ministry of Industrit's ), New Delhi

SHRI R. K. Gup'rA

Saar l\.f. L. GARG ( Alternate v

SHRI S. C. (;OPTA

SUUt V. K.J.HN

On. R C. MAHESW."H,l (A.[t~rnatt)

SHIH K. N. GAUR Cent r al Mechanical Engineering ResearchInstitute (CSIR ), Durgapur

St ate Farms Corporation of India Ltd, New Delhi

SHRI T. K. B. VAl\MA ( .titanate)

( Continued on pagl 2 )

(0 Copyright 19B3

INDI.\N STANDARDS INSTITUTIONThis publication is proter-ted under the Indian Copyright Act (XIV of 1957) andreproduction in whole or ill part by any means except with written perm ission of thepublishC'r !Ihall he dt>emcd to be an infringemE"nt of copyright unJer the 5aid Act.

IS: 10282 - 1982

(Conhnuedfrom pag~ 1)

Members

SH1\l G. N. MEH'rA

SURl G. C. PATEL ( Alternate)DR V. K. Ml'fTA.L

DR R. B. RAM iAltemat» )Sum]. S. MUDHAR

5Hm G. B. LAL { Alternale)SHRl H. M. MOTTA

Repr'sentingGujarat Tractors Corporation Ltd, Vadodara

Punjab Agricultural University. Ludhiana

H M T Limited ( Tractor Division}, Pinjore

Mahindra &.Mahindra Ltd ( International TractorDivision }, Bombay

SlIRT T. S. CU}'Y (.Wernate)SHm R. RoY

Sura M. V. VRNKATE~W1ARAN

(Alternate I)SHut A. R. SONALKAR ( Alternate r[ )

SHRI A. T. NAHI':NHP.1t VST Tillers Tractors Limited. BangaloreSuui V. P. MAliENDRA ( All,rna")

Sum S. T. N,utJ\YANASWAMY Hharat Earthmovers Ltd, BangaloreDR V. PANDUltANOA Tractors and Farm Equipment Ltd. Madras

Snnr S. R "NOANATHAN (Alternate)SURI S. B. PANDYA National Farmers Or~anization.New DelhiSum V. V. PATlJJ Bharat Krishak Sarna), New DelhiSHRI K. RAMKOMAR Kerala Agro Machinery Corporation Limited.

Ernakularn

DCV~~du~{~r:.) CO(~~~~i~~~;·r ~f~tT1ai~dUs~~;~:Nf'wDelhi

DR S. SA'l'YAI\.1UltTY Eicher Goodearth Limited, New Delhi01\j. BHA'f1'AOYAlLYYA (Alt,rnat,)

Sunr N. C. SAXll:NA. J. K. Satoh Agricu ltural Machines Limited.Kanpur

Su a t R. K. RAJPAl ( Allnnal')DR M. P. SINHA Department of Agriculture. Government of Bihar,

PamaSHRI K. S. YADAV Ministry of Agriculture ( Department of

Agriculture & Co-operation ) .0;ew DelhiSHIH T. PURNAla~DAM. Director Gcnr-ral , lSI ( E.'t-r!jfiClo Member)

Director \ Agri & Food)

SUTetar)SURl R. N. SHAIn,,,

CCP\lty Dirn tor ( Agri & Food). lSI

Power Tillers and Their Accessories Subcommittee, ArDC S2 : 1

COMMer

Sn n t R. N. PATIL

Members

SHItl BALAHM SawH

SURl A. P. VERMA ( Alltrna',)

Ministry of Agriculture ( Drparmt'nt ofAgriculture and Co-opcration }, New Delhi

Bihar State Agro Industr ics DevelopmentCorporation Ltd, Patna

AMENDMENT NO.1 OCTOBER 2007TO

IS 10282: 1982SPECIFICATION FOR CAGEWHEEL FORPOWER TILLERS

(PuRe 3, clause1.1)- Insert thefollowing clause after1.1:

'1.2 Types - Based on type of soil, four types of Cage wheels are used inPower Tillers.' .

(Page 4, clauses 3.1 to 3.5) - Substitute the following for the existingclauses:

'3.1 Theoverall diameter of the Wheel (ste A in Fig. 1) shall be within 650 to800mm.

3.2 Effective lugdiameter of the Wheel (set B in fig. 1) shall be within S7Sto780mm.

3.3Overall width ofthe Wheel(see C in Fig. 1)shallbe within 320to S50mm.

3.4 The fixing holes shallbe4 Nos. equally spaced and the diameter of holesshall beaminimum 14mm.

3.5The hub holediameter (seeD inFig. t) shallbewithin 80to \35 mm.'

(FAD II)

Reprography Unit. BIS. New Delhi, lnClia

IS s10282· 1982

Indian StandardSPECIFICATION FOR

CAGE WHEEL FOR POWER TILLERS

o. FOR E W 0 R D

0.1 This Indian Standard was adopted by the Indian StandardsInstitution on 31 August 1982. after the draft finalized by the AgriculturalTractors and Power Tillers Sectional Committee had been approved bythe Agricultural and Food Products Division Council.

0.2 Power tilIers are generally supplied with pneumatic wheels fortransportation and dry land cultivation. Studies indicate that theconversion of engine power into drawbar pull by these wheels is very poorwhen operated in puddled soil. Thi. may be due to either more slippageor higher roJling resistance from sinkage, or both. To improve tractionunder such conditions, most of the manufacturers have been supplyingdifferent types of cage wheels for power tillers.

0.3 In order to rationalize the dimensions, a need was felt to formulate anIndian Standard on the subject.

0.4 In preparation of this standard, assistance has been derived from thework done at Indian Institute of Technology, Kharagpur.

0.5 For the purpose of deciding whether a particular requirement of thisstandard is complied with, the final value, observed or calculated,expressing the result of a test or analysis, shall be rounded off inaccordance with IS: 2 .. I~60·. The number of significant placesretained in the rounded off value should be the same as that of thespecified value in this standard.

1. SCOPE

1.1 This standard specifies material. dimensions and other requirementsof cage wheel for power tillers.

-Rule. for rounding off numerical value. ("vis,d).

3

.1 I 10282 • 1182

2. MATERIAL

2.1 Th. material for varioul components luch as hub, braces, lUgI andrim of the cage wheel shall be mild steel (SII IS: 226-1975·) or anymaterial superior than this.

3. DIMENSIONS

3.1 The overall diameter of the wheel ( s" A in Fig. I) shallbe 700 ± 5 mm.

x

BRACES

.,'A

o

~SECTtON X X

~. .~

.~.%

FlO. 1 CAOE WHEEL FOR. POWB1l TILLER

3.2 Effective lug diameter of the wheel ($II B in Fig. I) shallbe 685± 5 mm,

3.3 Diameter of the lug base (see C in Fig. 1 ) shall be 610 ± 5 mm.

3.t Overall width of the rim ( see D in Fig. 1) shall be 200 ± 2 rom.

3.5 There shall be 20 lugs equally spaced over the lug base. Thedeviation in the lug spacing shall be not more than ± 2 mm, The lug

"Specifieation for structural .tee) (Itandard quality) (JftA,IlIi.riM).

4

IS a10282 • 1982

angle (sel at in Fig. 1 ) shall be 20 ± 1°. The nominal size of the anglesection for lug shall be 38 X 38 X 3 mm,

3.6 The fixing holes shall be 4 in number, equally spaced on the hub atthe pitch circle diameter (se, E in Fig. 1) of 115 ± 1·5 rom. Thediameter of the holes shall be 14·0 ± 1·0 mm.

3.7 The hub hole diameter (see F in Fig. 1 ) shall be 75 ± 1 mm,

3.8 The nominal size of the flat section for hub, rim and brace shallbe 180 X 8 mm, 44 X 6 rom and 25 X 6 mm respectively.

4. WORKMANSHIP AND FINISH

4.1 The components shall be free from pits, burrs, cracks and other visualdefects which may be detrimental for their use.

4.2 The various components shall be rigidly attached and welding shallnot be porous.

4.3 The com ponents shall be painted to prevent surface deterioration.

5. MARKING

5.1 Each cage wheel shall be marked with the manufacturer's name andregistered trade-mark, if any. Batch or code number shall also bemarked.

5.1.1 Each cage wheel may also be marked with the lSI CertificationMark.

NOTE - The ule of the lSI Certification Mark is governed by the provisions ofthe Indian Standards Institution (Certification Mark.) Act and the Rules andRegulations made thereunder. The lSI Mark on products covered by an IndianStandard conveys the assurance that they have been produced to comply with therequirement. of that standard under a well-defined system of inspection, teatingand quality control which is deviled and supervised by lSI and operated by theproducer, lSI marked products are also continuously checked by lSI for conformityto that standard at a further safeguard, Details of conditions under which alicence for the use of the lSI Certification Mark may by granted to manufacture...or procesaors, may be obtained from the Indian Standards Inatiturion,

6. SAMPLING FOR LOT ACCEPTANCE

6.1 Unless otherwise agreed to between the purchaser and the supplier,sampling of the cage w heel for lot acceptance shall be done in accordancewith 3 of IS : 7201-1974*.

·~lethod of lampling of agricultural machinery and tractorl.

5

IS • J1282 • 1112

R,/W,slft,in,Punjab Tracton Ltd. Ropar

SIIlU M. R. DEW••

Ssal J. PRASAD ( AI'"nal, )DIBIIOTOB

SHBI V. A. PATIL

M",.1J"sSBBI CJrA1fDBA MORAlf

SUB! G. S. RIHAL (.4.11"""")SIllU R. L. D••

SBBIR.TtWABl(AII~I)SHBI K. RAJU[UII.AB

Dire-ctorate of Agriculture, Gove-rnment of Assam,Gauhati

Tractor Training and Tetlinl Station (Ministryof Agriculture) J BudDi

Central IDldtute of Agriculture EOlfneering,{ lCAR. ), Bhopal

DB R. C. M.utauwA..BI ( All""." )EXBOUTlVB ENGINEER Directorate of Agriculture Government of Welt

Benlal, CalcuttaSHRI V. K. JAIle Directorate General of Technical DevelopmeDt

(Ministry of IDdUitriea), New DelhiSHRI T. K. B. VARMA ( AII""IJI, )

SaRI A. T. NAB_DD VST Tillen Tracton Ltd, BanlaloreSBBI V. P. MABENDIU. ( AI'mIIJ" )

SHlnJ. PADHI Directorate of Agriculture, Government orOrissa,Bhubhaneswar

Tractor TrainiDl Centre (MiDiJtry of "aricu!..ture),Hi..r

SBBI B. Roy

Kerala Agro Machinery Corporation Ltd,Ernakulam

Development Commissioner (Small ScaleInduatdea ). Ministry of IndUltl'iea New Delhi

S..I N. C. 81m..... J. K. Satoh Agricultural Machines Ltd, KanpurSHaI R. K. BAoJ.AI ( Al,,,tI4l, )

6