INTERNATIONALSTANDARD

ISO8503-5

First edition2003-07-01

Reference numberISO 8503-5:2003(E)

ISO 2003

Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part 5:Replica tape method for the determination of the surface profilePrparation des subjectiles d'acier avant application de peintures et de produits assimils Caractristiques de rugosit des subjectiles d'acier dcaps

Partie 5: Mthode de l'empreinte sur ruban adhsif pour la dtermination du profil de surface

This

is a

free

4 p

age

sam

ple.

Acc

ess

the

full v

ersio

n on

line.

ISO 8503-5:2003(E)

ii ISO 2003 All rights reserved

PDF disclaimerThis PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariataccepts no liability in this area.

Adobe is a trademark of Adobe Systems Incorporated.

Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

ISO 2003

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISO's member body in the country of the requester.

ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyright@iso.orgWeb www.iso.org

Published in Switzerland

This

is a

free

4 p

age

sam

ple.

Acc

ess

the

full v

ersio

n on

line.

ISO 8503-5:2003(E)

ISO 2003 All rights reserved iii

Contents Page

1 Scope .................................................................................................................................................... 12 Normative references .......................................................................................................................... 13 Terms and definitions .......................................................................................................................... 14 Principle ................................................................................................................................................ 25 Apparatus ............................................................................................................................................. 26 Maintenance and assurance of calibration for the replica tape method ........................................ 27 Procedure ............................................................................................................................................. 38 Specification of acceptable error ....................................................................................................... 39 Test report ............................................................................................................................................ 3

AnnexesAnnex A (informative) Measurement errors associated with replica tape determination of profile ..... 5Annex B (informative) Guidance on the correspondence between replica tape and ISO comparator determinations of profile ............................................................................................................................. 6

This

is a

free

4 p

age

sam

ple.

Acc

ess

the

full v

ersio

n on

line.

ISO 8503-5:2003(E)

iv ISO 2003 All rights reserved

Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.

The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by the technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. ISO shall not be held responsible for identifying any or all such patent rights.

ISO 8503-5 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 12,Preparation of steel substrates before application of paints and related products.

ISO 8503 consists of the following parts, under the general title Preparation of steel substrates beforeapplication of paints and related products Surface roughness characteristics of blast-cleaned steelsubstrates: Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive

blast-cleaned surfaces Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel Comparator procedure Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface

profile Focusing microscope procedure Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface

profile Stylus instrument procedure Part 5: Replica tape method for the determination of the surface profile

This

is a

free

4 p

age

sam

ple.

Acc

ess

the

full v

ersio

n on

line.

This is a free preview. Purchase the entire publication at the link below:

Looking for additional Standards? Visit SAI Global Infostore

Subscribe to our Free Newsletters about Australian Standards in Legislation; ISO, IEC, BSI and more

Do you need to Manage Standards Collections Online?

Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation

Do you want to know when a Standard has changed?

Want to become an SAI Global Standards Sales Affiliate?

Learn about other SAI Global Services:

LOGICOM Military Parts and Supplier Database

Metals Infobase Database of Metal Grades, Standards and Manufacturers

Materials Infobase Database of Materials, Standards and Suppliers

Database of European Law, CELEX and Court Decisions

Need to speak with a Customer Service Representative - Contact Us

This

is a

free

4 p

age

sam

ple.

Acc

ess

the

full v

ersio

n on

line.

TitlePage - Preparation of steel substrates before application of paints and related products S...TableofContent - Contents PageForeword - ForewordIntroduction - IntroductionScope - 1 ScopeNormativeReference - 2 Normative referencesClause1 - 4 PrincipleClause1 - 5 ApparatusUntitledSubclause2 - 5.1 Replica tapeUntitledSubclause2 - 5.2 Micrometer gaugeUntitledSubclause2 - 5.3 Compression tool

Clause1 - 6 Maintenance and assurance of calibration for the replica tape methodClause1 - 7 ProcedureClause1 - 8 Specification of acceptable errorClause1 - 9 Test report

AnnexInformative - Measurement errors associated with replica tape determination of profileAnnexInformative - Guidance on the correspondence between replica tape and ISO comparator determi...Clause1 - B.1 Replica tapeClause1 - B.2 Focusing microscopeClause1 - B.3 Stylus deviceClause1 - B.4 Comparison of different methods

Title: ISO 8503-5:2003 Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 5: Replica tape method for the determination of the surface profileTitleLink: