isolarcloud app commissioning guide
TRANSCRIPT
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 1 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
iSolarCloud APP Commissioning Guide
Disclaimer
The material in this document has been prepared by Sungrow Australia Group Pty. Ltd. ABN
76 168 258 679 and is intended as a guideline to assist solar installers for troubleshooting. It
is not a statement or advice on any of the Electrical or Solar Industry standards or guidelines.
Please observe all OH&S regulations when working on Sungrow equipment.
Version Revision History Created and Review by Date
1.0 Issued for Approval Service Team (Australia) 04th Jan 2021
1.1 Issued for Revision Service Team (Australia) 20th May 2021
This document only applies to all Sungrow inverters for monitoring solutions.
The information in this document may contain predictive statements including, without
limitation, statements regarding the future financial and operating results, future
product portfolio, new technology, etc. There are several factors that could cause
actual results and developments to differ materially from those expressed or implied
in the predictive statements. Therefore, such information is provided for reference
purpose only and constitutes neither an offer nor an acceptance. Sungrow Power may
change to this document without notice as we continuously improving our services.
If you have any questions relation to iSolarCoud commissioning procedures, please
take photos if you are on site and contact Sungrow Service Department on 1800 786
476 or email to [email protected], Monday- Friday 9am - 5pm (AEDT).
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 2 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
Contents
1. Download iSolarCloud App .................................................................................. 3
2. Server Selection .................................................................................................. 3
3. Register an Account ............................................................................................ 4
3.1 The account type for Distributor/ Installer ......................................................... 4
3.2 The Organization Code for Distributor/ Installer Account .................................. 5
3.3 The account type for End user .......................................................................... 6
4. Plant Creation ...................................................................................................... 7
4.1 Initial Configuration ........................................................................................... 7
4.2 Plant Configuration ......................................................................................... 10
4.3 Tariff Configuration ......................................................................................... 10
4.4 Put in the Organization Code or End-user Email Address .............................. 11
5. WiFi Configuration ............................................................................................. 13
6. Common Issue................................................................................................... 15
6.1. Cannot Connect to SG Signal ........................................................................ 15
6.2. Resume Commissioning ................................................................................ 15
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 3 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
1. Download iSolarCloud App
Search iSolarCloud in App Store or Google Play Store or scan the QR code below to
download and install iSolarCloud on the mobile.
2. Server Selection
On opening iSolarCloud, a prompt will appear to switch servers. Click on “Switch” and
then select Australian Server. This will update the app server and automatically go
back to the login page.
This can also be checked and changed by clicking “Select Server” under settings.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 4 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
3. Register an Account
Click RIGISTER to create a new account. Then, a user registration page will be shown
on the screen where the server and account type can be selected.
Select Australian server and choose the relevant account type to register an account.
3.1 The account type for Distributor/ Installer
The installer or retailer can select the account type for Distributor/ Installer. Put in the
email address and send verification code. Finished the blanks as required, tick Accept
Privacy Policy and click Register. After, a reminding for registration successful will
show up and click Proceed to Log in. From the log-in page, put in the email address
and the password set previously to log in the account.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 5 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
3.2 The Organization Code for Distributor/ Installer Account
After logging in as an installer account, click More at the bottom. Then click Profile,
and Organization Code could be found under organization information. This code is
for the installer / retailer to better manage the plants. By adding this code under the
customer account, the installer/ retailer can also get the customer’s plant shown in the
installer’s account. Alternatively, this code can be used to share it with a lower-level
account to gain access to all their plants. By clicking the plant, the installer can access
the customer’s account to check the working status of the inverter.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 6 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
3.3 The account type for End user
The owner of the inverter normally chooses the End User option. After filling the email,
a verification code can be requested, and the other relevant details can be entered.
Compared to Distributor/ Installer Account, the End User account does not have
organization code.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 7 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
4. Plant Creation
4.1 Initial Configuration
To create a plant, open iSolarCloud, login to the account and click “ ” on top right
corner. Select the relevant plant type and then the inverter type.
Next step will be to scan the communication module connected to the inverter. Various
communication modules include V312 Wi-Fi dongle, Wi-Net Dongle, EyeM4,
Logger1000, etc. In this document, the steps to configure a V312 Wi-Fi dongle are
shown. For other setups, please refer to the relevant documents below.
• Wi-Net Configuration
• Logger1000 / EyeM4 (Wi-Fi & 4G) Configuration
Once the dongle is scanned, the app will request to connect to the SG Wi-Fi signal. If
the SN is input manually, select the WLAN for V312 and Ethernet for E-Net.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 8 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
For WLAN, open the WiFi settings on the mobile, and join the SG signal. The password
should be the same as the serial number of the WiFi dongle (if required). There will be
a tick in front of the SG signal if successfully joined -> Go back to iSolarCloud and click
Next-> Select the local network shown on the list and put in the password.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 9 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
The successfully connected page will show up -> Reconnect home network instead of
SG signal or just disconnect WiFi on the phone settings->Click next on the new page
showing successfully connected and device is connected to the internet->click
Next->Directly click next in Add Inverter page.
Here any additional inverters can be added using the same procedure.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 10 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
4.2 Plant Configuration
After clicking Next on Add inverter page, the Configure Plant page will be shown up. If
location service was allowed for iSolarCloud app, the plant location will be filled in
automatically. Finished all the blanks as required and click next.
4.3 Tariff Configuration
In Configure Tariff page, put in the tariff values provided by local grid company. If there
are different prices for peak period or other periods, iSolarCloud also supports to
provide more than one special periods for special prices. Turn on the button of Time-
of-Use Tariff, click Add Time-of-Use Tariff ,and put in the price, start time and end time
for Time Segment.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 11 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
After that click confirm. If more time segments need to be added, just need to repeat
the previous process. The price for other periods could be set by clicking other time,
putting in the price and confirm. After that, click Next.
4.4 Put in the Organization Code or End-user Email Address
If the plant is created by an end-user account, it will require to put in the organization
code of the installer or distributor, and return back to Dashboard. If the plant is created
by an installer account, the end-user email address needs to be put in.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 12 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
If the end user does not already have an account, they will then receive an email with
the login details which they can use to login and access the plant.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 13 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
5. WiFi Configuration
1) Insert WiFi dongle to the inverter and wait until the first LED light which labelled
as “RUN” turns on.
2) In mobile WiFi settings, search for the WiFi “SG-XXXXXXXX” and connect. If a
password required, use the serial number of the dongle as the password.
3) Choose either Method 1 or Method 2 below to complete WiFi configuration
4) After connecting successful, all three LED lights on WiFi dongle should be on.
Method 1: Open iSolarCloud -> click “ ” -> select “WLAN Configuration”-> Scan
the QR code on the WiFi dongle -> se lect the WiFi network and p ut in the password.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 14 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
Method 2: Open iSolarCloud -> Local Access -> WLAN ->Login inverter with the
account “admin” and password “pw8888” -> WLAN Configuration ->select the WiFi
network and put in the password.
GD_202105_All_iSolarCloud APP Commissioning Guide_V1.1 Page 15 of 15
© Sungrow Australia Group Pty. Ltd. All rights reserved. As we continuously improving our services, changes to this document may occur without notice.
6. Common Issue
6.1.Cannot Connect to SG Signal
It could happen sometimes that the mobile cannot join the SG signal of the dongle
when doing WiFi configuration.
The reason for the problem is that the signal has been occupied by another device. In
this case, it is necessary to check if the dongle is already connected with another
mobile device such as iPad. After disconnecting the connection, try to connect to the
SG network again.
6.2.Resume Commissioning
Sometimes when creating the plant on the iSolarCloud, the process might be stuck in
resume commissioning. The reason for this is that the WiFi configuration has not been
done properly. Often when the router’s signal strength is weak (far away or several
obstacles), the inverter can disconnect hence, showing resume commissioning. Also,
the router must be able to access the internet normally. To rectify the issue, remove
the WiFi dongle from the inverter and plug it in again. Then redo the WiFi configuration
as per Section 4 in this document. To log out the app, follow the steps below.