j-frm-0101 revision with reason no.dateinitials drawing no. d’vinyl inc. descriptive part name...
TRANSCRIPT
J-FRM-0101
Revision with ReasonNo. Date Initials
Drawing No.
D’Vinyl Inc.Descriptive Part Name
Designed by Checked by Engineer
Drawing Type
Foot Plate
Date of This RevisionDrawing Issue Date
Drawing Size Scale as Drawn Scale as Printed
Engineer Phone #
Parts ListQuantity Supplier
Quantity Required
26part A 8 x10 1:1, 1in=1in
D. Quesnel D. Quesnel
275-521502/27/99 02/27/99
1:1 =100%
NOTES:Suitable for CNC Milling
Material: Cold Roll Steel
four per frame exceptsix for process zone frameTotal 4X5+6=26
Stock Finish OK ALL SURFACES
Match Radii of 3.5” Square Tube
Nominal Dimension so Foot fits and centers inside 3.5” square Tube
Break sharp edges and corners
All dimensions in inch units.
Unless otherwise indicated,use default tolerances belowx.x +/- 0.050”x.xx +/- 0.010”x.xxx +/- 0.005”Angles +/- 2o
0.500.75 (stock Thickness)
3.50
3.50
Tap Through Hole3/4 -10
3/16 Four Sides
A
A
B
B
1.75
1.75
J-FRM-0102
Revision with ReasonNo. Date Initials
Drawing No.
D’Vinyl Inc.Descriptive Part Name
Designed by Checked by Engineer
Drawing Type
Foot Plate Assembly
Date of This RevisionDrawing Issue Date
Drawing Size Scale as Drawn Scale as Printed
Engineer Phone #
Parts ListQuantity Supplier
Quantity Required
26Assembly A 8 x10 1:1, 1in=1in
D. Quesnel D. Quesnel
275-521502/27/99 02/27/99
1:1 =100%
NOTES:
3/16 inch 6-32 pointed set screws
Set Screws Must be on exterior surfaceand interior surface so both set screwsare accessible after frames are buttedtogether.
Centering of Set screws is visual Center
Break sharp edges and corners
All dimensions in inch units.
Unless otherwise indicated,use default tolerances belowx.x +/- 0.050”x.xx +/- 0.010”x.xxx +/- 0.005”Angles +/- 2o
View of Bottom of Frame Leg Looking in Process Direction
A
A
1/8
Tap 6-32 Two PlacesCentered on Inside and Outside Faces
Jam Nut
3/4-10 Hex HeadCap Screw-Grade 5
3/4 -10 1.5 inch Hex Head Cap Screw1 each Any Vendor
3/4 -10 Jam Nut1 each Any Vendor
6-32 pointed allen set screw, 3/16 length2 each Any Vendor
Foot Plate, J-FRM-01011 each RCIMS
J-FRM-0103
Revision with ReasonNo. Date Initials
Drawing No.
D’Vinyl Inc.Descriptive Part Name
Designed by Checked by Engineer
Drawing Type
Alignment Tab
Date of This RevisionDrawing Issue Date
Drawing Size Scale as Drawn Scale as Printed
Engineer Phone #
Parts ListQuantity Supplier
Quantity Required
10Part A 8 x10 1:1, 1in=1in
D Quesnel D.Quesnel
275-52153/3/99 3/3/99
1:1 =100%
Material: 1/2” Cold Rolled Steel
NotesTwo per framejoining 2X(6-1)=10
Holes 1.75 inch on centersSlot and Holes on Centerline
Radius Nominal 1/8, 1/4” Mill Finish OK
2.000.750
1.00
6.75
1.75
4.25
2.500.44 (nominal 7/16)
Through DrillClearance for 3/8-24A
A
Break sharp edges and corners
All dimensions in inch units.
Unless otherwise indicated,use default tolerances belowx.x +/- 0.050”x.xx +/- 0.010”x.xxx +/- 0.005”Angles +/- 2o
0.50
+.010-.000
Tap for1/4-20
J-FRM-0104
Revision with ReasonNo. Date Initials
Drawing No.
D’Vinyl Inc.Descriptive Part Name
Designed by Checked by Engineer
Drawing Type
Alignment Tab Slider
Date of This RevisionDrawing Issue Date
Drawing Size Scale as Drawn Scale as Printed
Engineer Phone #
Parts ListQuantity Supplier
Quantity Required
###Part A 8 x10 1:1, 1in=1in
D. Quesnel D. Quesnel
275-52153/3/99 2/2/99
1:1 =100%
Material: Cold Rolled Steel
Notes
Holes 1.75 inch on centers
Sliding fit into Slot in Alignment Tab
Break sharp edges and corners
All dimensions in inch units.
Unless otherwise indicated,use default tolerances below
x.x +/- 0.050”x.xx +/- 0.010”x.xxx +/- 0.005”Angles +/- 2o
1.750
2.375
0.3125Clearance for 3/8-24, Two Places
0.750.375
0.50
AA
J-FRM-0105Drawing No.
D’Vinyl Inc.Descriptive Part Name
Designed by Checked by Engineer
Drawing Type
Alignment Tab Assembly
Date of This RevisionDrawing Issue Date
Drawing Size Scale as Drawn Scale as Printed
Engineer Phone #
Parts ListQuantity Supplier
Quantity Required
NAAssembly A 8 x10 1:1, 1in=1in
D Quesnel D. Quesnel
275-52153/3/99 3/3/99
1:1 =100%
NotesAll holes 1.75 inch on center Line of 3.5”Square Tube. -Use Drill Jig then tap holes for 3/8 -24Bolt to Frame Just below lower Cross Member, inside frame.Use Allen Set Screw to Pull Frames Together. Spread Clamping Loadto tab using washers
Break sharp edges and corners
All dimensions in inch units.
Unless otherwise indicated,use default tolerances belowx.x +/- 0.050”x.xx +/- 0.010”x.xxx +/- 0.005”Angles +/- 2o
Belville Washers
3/8-24 Allen Head Cap Screws
Slider
1/4-20Flat End Set Screw
Height of Lower Cross Member
Alignment Tab
Junction of EndSections of adjacentFrames
1 J-FRM-0103 RCIMS
1 J-FRM-0104 RCIMS
4 1 inch outer Diameter Washer Any Vendor
4 3/8-24 Allen Head 5/8 Length Any Vendor
Revision with ReasonNo. Date Initials
1.50 inches below to allow clearance for Weld