job aid w10573282 kitchenaid dishwasher manual

8/19/2019 JOB AID W10573282 KitchenAid Dishwasher Manual

http://slidepdf.com/reader/full/job-aid-w10573282-kitchenaid-dishwasher-manual 1/120

KD-15

TECHNICAL EDUCATION

2013 Stainless SteelTall Tub Dishwasher

KUDE20FB*0, KUDE20IX*9, KUDE40FX*6, KUDE48FX*5,

KUDE50CX*9, KUDE50FB*0, KUDE60FX*5, KUDE60HX*5,

KUDE70FX*5, KUDL15FX*6

*All Colors

JOB AID W10573282



ii n KitchenAid 2013 Tall Tub Stainless Steel Dishwasher

FORWARD

s KA Jo A 2013 lss l ll Dssr r o W10573282 ros I-o r rossol oro o sllo oro sr o lolWs s rl s s r oors or s or oro o ol sr rr o s Cr ro ssr

GOALS AND OBJECTIVES

ol o s Jo A s o ro oro ll l I-o r rossol ororl os los rr KA 2013 lss l ll Dssr

os o s Jo A r o

rs ollo ror s ros

ssll rolsoo os los ssll ror ssr rrs

ssll rr ssr o s ror orol ss

WIOO COOAIO sss o rsosl or rrs o orros o or or I-o r rossols

Cor 2013 Wrlool Cororo Bo ror I 022



KitchenAid 2013 Tall Tub Stainless Steel Dishwasher n ii

TABLE OF CONTENTS

KitchenAid 2013 Stainless Steel Tall Tub Dishwasher

SECTION 1 ENEAL INFOATION

DISHASHE SAFET 12BEFOE USIN OU DISHASHE 13ODEL SEIAL NUBE LABEL 14TECH SHEET LOCATION 14ODEL SEIAL NUBE NOENCLATUE 15ODUCT SECIFICATIONS 16ATS FEATUES 17NOTES 18

SECTION 2 OEATION

STATU UICK EFEENCE 22UICK STES 23DISHASHE USE 23CCLE OTION DESCITIONS 25DISHASHE FEEDBACK SECTION 28DISHASHE FEATUES 29FILTATION SSTE 211DISHASHE CA E 213CONSUE TOUBLESHOOTIN UIDE 214NOTES 216

SECTION 3 INSTALLATION

DISHASHE SAFET 32INSTALLATION EUIEENTS 34LOCATION EUIEENTS 35DAIN EUIEENTS 37ELECTICAL EUIEENTS 37INSTALLATION INSTUCTIONS 38DETEINE CABINET OENIN315INSTALL DOO HANDLE316INSTALL CUSTO ANEL 316CHOOSE ATTACHENT OTI ON 319EAE ATE SUL LINE 320CONNECT ATE SUL322CONNECT TO DAIN 322AKE DIECT IE ELECTICAL CONNECTION 323SECUE DISHASHE TO CABINET OENIN 325CO LETE INSTALLATION 326

NOTES 328

SECTION 4 COONENT ACCESS

INSULATION BLANKET 42DOO LATCH STIKE 42ADUSTABLE DOO SINS 43ATE INLET DAI N HOSE 43OEFI LL ASSEBL 44ACCESSIN DOO COONENTS 45



i n KitchenAid 2013 Tall Tub Stainless Steel Dishwasher

ODUCT SECIFICATIONS AANT INFOATION SOUCES s or

EOIN USE INTEFACE 46E OIN LATCH ASSE BL 47EOIN ELECTONIC CONTOL BOAD 48EOIN DISENSE ASSEBL 49SA AS, FEED TUBE, AND ANIFOLD 410TUB COONENTS STAINLESS STEEL TUB ODELS 411EOIN THE UE ACKS 412

EOIN LOE SA A 413E OIN FILTES 414EOIN OSCUB ANIFOLD 415EOIN DIETE DISK415UNDE THE TUB COONENTS 418HEATE419EOIN SU ASSEBL DAIN U 420EOIN OTICAL ATE INDICATO 423EOIN DIETE OTO 424ASH OTO ELACEENT 425

SECTION 5 DIANOSTICS TOUBLESHOOTIN

SAFET ANINS 52ASH CCLES 53SEICE DIANOSTIC CCLE 54SEICE DIANOSTIC CCLE NOTES 55DIANOSTIC UIDE 55SEICE DIANOSTICS ITH EO CODES 56SEICE EO CODES 57TOUBLESHOOTIN UIDE 512

SECTION 6 TESTIN

SAFET ANINS 62I IN DIAA 63

CONTOL BOAD INFOATIONSECS 64COONENT TESTIN 64ELECTONIC CONTOL BOAD 65ENEAL THEO OF OEATION 66OE CHECK 66DOO SITCH CICUIT 67FILL CICUIT 68DISENSE CICUIT 69ATE H EATIN HEAT D 610ATE SENSIN ITH OI SENSO 611DIETE OTO 612DIETE SENSO OSITION SITCH 613ASH OTO AIABLE SEED614DAIN OTO AIABLE SEED 615

ENT AX OTO 616ENT FAN 617USE INTEFACE 618



ENEAL INFOATION

KitchenAid 2013 Tall Tub Stainless Steel Dishwasher n 11

S G I

s so ros rl s rs oro or KA lss l ll Dssr

■ Dssr

■ Bor s or Dssr

■ ol rl r l

■ oos

■ ol rl r olr

■ ro os

■ rs rs

■ os



12 n KitchenAid 2013 Stainless Steel Tall Tub Dishwasher

ENEAL INFOATION

D S

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don'tfollow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IOTANT SAFET INSTUCTIONSANIN W s ssr ollo s ros l ollo

■ ll sros or s ssr

■ s ssr ol or s o

■ s ol rs or rs s ro ors ssr o o r olr

■ W lo s o s

1 o sr s so r o ll o

oor sl 2 o sr s ls o r

rs o - rs

■ Do o s ls s lss r rssr s or l or ls s oso r rrs roos

■ Do o o l r or lr s

■ Do o or ssr lss ll losrls r rorl l

■ Do o r orols

■ Do o s s o or s o oor l or srs o ssr

■ o r rs o r o o llo lr o l or o ssr

■ r r oos ro s ro o r ss s o s or o

s or or DO A I OI I or ss s o s or s ro ors ssr r o ll o r s l r o ro or srl s sll rls l ro s As s sl o o so or s o rs

■ o oor or l o s or ro ol ssr ro sr orsr

SAE THESE INSTUCTIONS

o Clor rooso 5 Wrs

ANIN s ro os o or or ls o o o Clor o s r

ANIN s ro os o or or ls o o o Clor o s r s or or

rro r



ENEAL INFOATION


B D

Isll r ssr s slr ro lsAo ossl rr o ll l ro r rrs r o or rr orso or r sor oro

Isll ll ssr o oor ll ol r sl or s s s

o ll s ls ro oss oorss s o r ol or sll Isllo Isros or ol oro

OUNDIN INSTUCTIONS

Fr a rune, rnnete ishwasher ssr

s ro I o lo orro ro ll r rs o lrso ro o ls rss or lrrr ssr s or -ro oor ro l l s l o ror ol s sll ro or ll lolos orsANIN Iror oo o -ro oor rsl rs o lr soC l lr or sr rrs o r o r ssr s rorlro Do o o l ro ssr ll o ol ror olsll l lr

Fr a eranentl nnete ishwasher ssrs o o ro l rr ss or -ro oor s r r oors o o -ro rl or l o ssr


Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.Do not use an extension cord.

Failure to follow these instructions can result indeath, fire, or electrical shock.




ENEAL INFOATION

Model & Serial NumberLabel Location

Tech Sheet Location(Behind Toe Kick Panel)

S N L

T S L



ENEAL INFOATION


S N N

ODEL NUBE K UD E 60 F X BL 5

INTENATIONAL SALES O

AKETIN CHANNEL

K KITCHENAID BAND

ODUCT IDENTIFIE

D Cnertiblertable UD Unerunter

E TIFILTE SSTE

SEIES CONFIUATION

FEATUES

F Full Interate Dr C 25 Cnsle wDisla I 25 Cnsle

H Heritae S ater Stener

EA OF ODEL INTODUCTION

X 2010 B CU el

COLO CODE

H hite SS Stainless Steel BL Bla

BT Bisuit S Stainless rline A anel ea

ENINEEIN CHANE

0 Basi elease 1 First eisin 2 Sen eisin

SEIAL NUBE F 2 25 10000

ANUFACTUIN SITE

F FINDLA, OH

EA OF ANUFACTUE

2 2012

EEK OF ANUFACTUE

ODUCT SEUENCE NUBE




ENEAL INFOATION

S

Line Voltage: 120 AC

Frequency: 0

Amps: 10A

Low Volts Power Supply: 15 13 5 33

Water Pressure: 120 s 20 s

Supply Water Temperature: - 120 C

Control: lro Corol Ir Corol

Wash Motor: 3-s rl oor

Drain Motor: 3-s rl oor Diverter Motor: 120 AC

Fill Valve: 120 AC

Heater: 120 AC

Dispenser: 120 AC

Spray Arm Motor: 120 AC so ols

Fan Motor: 5 DC so ols

Sensors: rr sor

Wr sor OWI

r Ar sor so ols

Switches: Drr oso 5 DC

Door 13 DC

lo 120 AC

TCO / BiMetal: Ioror o Corol Bor sl los

Fuses: 1 s

oor Corol s

r s

Lower Wash Arm: Ds

Upper Wash Arm: r Ds

Filtration: 3- lr s

ProScrub: All o r ols

Water Softener Model: KD0

DISHASHER SPECIFICATIONS



ENEAL INFOATION


F

Upper level wash

Model and serial number label

Water inlet opening

Heating element

Detergent dispenser

Water feed tube

Lower spray arm

Overfill protection float

Control panel

BOTTOM RACK

TOP RACK

Flexible fold-down tines

(on some models)Cup shelves with

stemware holder

Silverware basket

Upper spray arm

Flexible fold-down tines

Rinse aid dispenser reduces spotting and improves drying.

ProScrub ® (on some models)

powerful jets target water toward pots,

pans, or casserole dishes loaded in the

back of the dishwasher to clean

stubborn messes.

EQ Filtration System removes soil

from water and improves cleaning action.

Pressurized spray nozzles and variable

speed motor provide effective cleaning.

Culinary Caddy ®

utensil basket

(on some models)

Culinary tool rack/3rd level rack

(on some models)

Rack handle

Premium top rack

adjusters




ENEAL INFOATION

N



OEATION

KitchenAid 2013 Stainless Steel Tall Tub Dishwasher n 21

S O

s so ros orol s r oro or KA lss l ll Dssr

■ r- r

■ s

■ Dssr s

■ Cl Oo Dsros

■ Dssr o

■ Dssr rs

■ lro s

■ Dssr Cr

■ Cosr rolsoo

■ os




OEATION

S R

Clean EQ Wash System removable filters to maintainpeak performance.

Cleaning the filtersperiodically helps keep the

dishwasher working at peakperformance. The filters canbe found at the bottom centerof your dishwasher.

See the “Filtration System”section for information onremoving and maintaining thefilters.

IMPORTANT: Do not block detergent dispenser.

Tall items placed in the lowerrack may block the dispenserdoor. Cookie sheets and

cutting boards loaded on theleft-hand side of thedishwasher can easily blockthe dispenser. If detergent isinside of the dispenser or onthe bottom of the tub after thecycle is complete, thedispenser was blocked.

Drying - Rinse Aid is essential.

You must use a drying agentsuch as a rinse aid for gooddrying performance (sampleincluded). Rinse aid along

with the Heat Dry or ProDry™option will provide best dryingand avoid excessive moisturein the dishwasher interior.

1 Hour Wash - When you need fast results.

Efficient dishwashers run longer to save waterand energy, just as driving a car slower saveson gas. When you need fast results, the1 Hour Wash will clean your dishes usingslightly more water and energy. Select theHeat Dry or ProDry™ option to speed drying

times (adds approximately 27 to 35 minutesto the 1 Hour Wash cycle)

P U S H

DOWN &T U R N

L O C K U

N L O

C K

USE RINSE AID FOR

BETTER DRYINGLock

Refill

Full

Add

or

ProWash™ cycle for optimal cleaning

The most advanced and versatile cycle.ProWash™ cycle senses the load size, soilamount, and toughness of soil, to adjust thecycle for optimal cleaning using only theamount of water and energy needed. TheProWash™ and Heavy Duty cycles arerecommended for tough soil. No need toprerinse dishes; just scrape and load.

ProScrub® Option for loading to clean baked-onfood (some models)

When the ProScrub®

option is selected, itprovides aconcentrated washon the back of thelower dish rack forhard-to-clean dishes.Place these dishes

with the soiledsurface of the dishtoward theProScrub® spray jetsin the lower rack ofthe dishwasher.

Press START/RESUME every time youadd a dish.

IMPORTANT: If anyone opens the door (suchas, for adding a dish, even during the DelayHours option), the Start/Resume button mustbe pressed each time.

If the Start/Resume button is located on top ofdoor: Push door firmly closed within3 seconds of pressing START/RESUME. If thedoor is not closed within 3 seconds, the Start/ Resume button LED will flash, an audible tonewill be heard, and the cycle will not start.

Proper Detergent Dosing

It is possible to use too much detergent in your dishwasher.This can lead to etching of your dishes. See “Add Detergent” inthe “Dishwasher Use” section, to determine the amount ofdetergent needed based on your water hardness.



OEATION


S

1Prepare and loaddishwasher. 3

Select a cycle and option.

2 Add detergentfor cleaning andrinse aid fordrying.

4Start dishwasher.

NOTE: If the Start/Resume button is locatedon the top of door, push door firmly closedwithin 3 seconds of pressing START/RESUME.

I

-

Prepare and Load the Dishwasher

IMPORTANT: Remove leftover food, bones, toothpicks and otherhard items from the dishes. Remove labels from containers beforewashing.

■ Make sure that when the dishwasher door is closed no itemsare blocking the detergent dispenser.

■ Items should be loaded with soiled surfaces facing down andinward to the spray as shown. This will improve cleaning anddrying results.

■ Avoid overlapping items like bowls or plates that may trap food.

■ Place plastics, small plates and glasses in the upper rack.Wash only plastic items marked “dishwasher safe.”

■ To avoid thumping/clattering noises during operation, loaddishes so they do not touch one another. Make sure lightweightload items are secured in the racks.

■ Improper loading can cause dishes to be chipped or damaged.When loading glasses or mugs, it is best to load these items inbetween rows of tines instead of loading them over tines, asshown in the image above.

Add Detergent

NOTE: If you do not plan to run a wash cycle soon, run a rinsecycle. Do not use detergent.

■ Use automatic dishwasher detergent only. Add powder, liquidor tablet detergent just before starting a cycle.

■ Fresh automaticdishwasher detergentresults in bettercleaning. Store tightlyclosed detergentcontainer in a cool, dryplace.

■ The amount of detergent to use depends on:How much soil remains on the items - Heavily soiled loadsrequire more detergent.

The hardness of the water - If you use too little in hard water,dishes won't be clean. If you use too much in soft water,glassware will etch.

Soft to Medium Water (0-6 grains per U.S. gallon)[typical water softener water and some city water]

Medium to Hard Water (7-12 grains per U.S. gallon)[well water and some city water]

■ Depending on your water hardness, fill the Main Wash sectionof the dispenser as shown. Fill the Pre-Wash section to thelevel shown, if needed.

STEP 1

Upper rack Lower rack

Make sure nothing keeps spray arm(s) fromspinning freely. It is important for the waterspray to reach all soiled surfaces.

■ When loading silverware, always place sharp

items pointing down. Mix items in eachsection of the basket with some pointing upand some down to avoid nesting. Spraycannot reach nested items.

STEP 2

A. Cover latch

B. Main Wash section

C. Pre-Wash section

A

B C

MAIN WASH

PRE-

WASH

Soft Water

Hard WaterSoft Water

Hard Water

D




OEATION

D

NOTE: Fill amounts shownare for standard powdereddetergent. Followinstructions on the packagewhen using other dishwasherdetergent types.Premeasured forms are suitable for all hardness and soil levels.

Always place premeasured detergents in the main compartmentand close the lid.

Add Rinse Aid

■ Your dishwasher is designed to use rinse aid for good dryingperformance. Without rinse aid your dishes and dishwasherinterior will have excessive moisture. The heat dry option willnot perform as well without rinse aid.

■ Rinse aid keeps water from forming droplets that candry as spots or streaks. They also improve drying byallowing water to drain off of the dishes after the finalrinse.

■ Rinse aid helps to reduce excess moisture on the dishracks and interior of your dishwasher.

■

Check the rinse aid indicator. Add rinse aid when indicatordrops to “Add” level.

■ To add rinse aid, turn the dispenser capto “Refill” and lift off. Pour rinse aid intothe opening until the indicator level is at“Full.” Replace the dispenser cap andturn to “Lock.” Make sure cap is fullylocked.

NOTE: For most water conditions, thefactory setting of 2 will give goodresults. If you have hard water or noticerings or spots, try a higher setting. Turnthe arrow adjuster inside the dispenserby either using your fingers or insertinga flat-blade screwdriver into the centerof the arrow and turning.

Select a Cycle (cycles vary by model)

See “Cycle and Option Descriptions” charts in the followingsection.

Efficient dishwashers run longer to save water and energy, just asdriving a car slower saves on gas. Typical cycle time isapproximately 2¹ ⁄ ₂ hours, but can take less or more time tocomplete depending on selections.

Select Options (options vary by model)

See “Cycle and Option Descriptions” charts in the followingsection.

You can customize your cycles by pressing the options desired. Ifyou change your mind, press the option again to turn off the option.Not all options are available for every cycle. If an invalid option isselected for a given cycle, the lights will flash.

Start or Resume a Cycle

■ Run hot water at the sink nearest your dishwasher until thewater is hot. Turn off water.

■ Press START/RESUME once to show whichselections you used. Select the wash cycle andoptions desired OR press START/RESUME to repeatthe same cycle and options as in the previous washcycle.

IMPORTANT: If anyone opens the door (such as, for adding a dish,even during the Delay Hours option), the Start/Resume buttonmust be pressed each time.

■ If the Start/Resume button is located on top of door, push doorfirmly closed within 3 seconds of pressing START/RESUME. Ifthe door is not closed within 3 seconds, the Start/Resumebutton LED will flash, an audible tone will be heard, and thecycle will not start.

Soft Water

Hard Water

Soft Water

Hard Water

Main Wash Pre-Wash

Full

Add

¹ ⁄ ₄ turn to lock

Lock

Refill

STEP 3

STEP 4



OEATION


C O D

This information covers several different models. Your dishwasher may not have all of the cycles and options described.

Wash times depend on water temperature, heavy soil condition, dish load size and options selected. Adding options will add time to thecycle.

* Adding options will add time to the cycle. See options information section.

** This is the approximate cycle time obtained with 120°F (49°C) hot water available at the dishwasher. Increase in time results from lowtemperature of the incoming water.

CYCLE SELECTIONS

CYCLES SOIL LEVEL WASH TIME* (MINS.)W/O OPTIONS

WATERUSAGE

GALLONS(Liters)Typical** Max

The most advanced and versatile cycle. ProWash™cycle senses the load size, soil amount, and toughnessof soil, to adjust the cycle for optimal cleaning usingonly the amount of water and energy needed.

Light to Medium 110 150 4.2 (16.1)

Tough/Baked-On 125 190 5.0 (19.1)

Heavy 125 190 6.8 (25.8)

Use for hard-to-clean, heavily soiled pots, pans,casseroles, and regular tableware.

Light to Medium 130 150 5.0 (19.1)

Heavy/Baked-On 140 205 6.8 (25.8)

Use for loads with normal amounts of food soil. Theenergy-usage label is based on this cycle.

Light to Medium 110 150 4.0 (15.0)

Heavy 125 190 6.8 (25.8)

Use for lightly soiled items or china and crystal. Light to Medium 105 145 4.2 (15.2)

Heavy/Baked-On 120 185 6.8 (25.8)

When you need fast results, the 1 Hour Wash will cleandishes using slightly more water and energy. Select theHeat Dry or ProDry™ option to speed drying times (addapproximately 27 to 35 minutes to the 1 Hour Washcycle).

All soil levels 58 62 7.9 (30.0)

Use for rinsing dishes, glasses, and silverware that willnot be washed right away.

Do not use detergent.

All soil levels 17 20

OPTION SELECTIONS

OPTIONS CAN BESELECTED WITH

WHAT IT DOES ADDED TIME TO CYCLE ADDEDWATERGALLONS

(LITERS)

TYPICAL MAX

Cleans pans, casseroles,etc., with tough food soilto eliminate the need forsoaking and scrubbing ofdirty, baked-on dishes.

Heavy DutyNormal Wash

Activates theProScrub® spray jets to provideintensified cleaningpower to items atthe back of thelower rack.

53 73 0 - 3.0

(0 - 11.2)

Raises the main washtemperature to improvecleaning for loadscontaining tough, baked-on food.


Raises the mainwash temperaturefrom 105°F (41°C)to 120°F (49°C).

22 40 0 - 3.0

(0 - 11.2)




OEATION

C O D

Sanitizes dishes andglassware in accordancewith National SanitationFoundation (NSF)/ANSIStandard 184 forResidential Dishwashers.Certified residentialdishwashers are notintended for licensed foodestablishments. The Saniindicator indicates at theend of the cycle whetherthe Sani Rinse option wassuccessfully completed. Ifthe indicator is notactivated, it is probablydue to the cycle being

interrupted.


Increased the mainwash temperaturefrom 105°F (41°C)to 130°F (54°C) andthe final rinse from140°F (60°C) to155°F (68°C).

53 73 0 - 3.0(0 - 11.2)

For added convenience,use for washing a smallload of dishes in the toprack to help keep thekitchen continuouslyclean.

Available with anycycle

Cannot be usedwith ProScrub®

Option

Slightly faster washfor smaller loads

-7 -30 0

Dries dishes with heat anda fan. This option with theuse of rinse aid will providethe best dryingperformance. Plastic itemsare less likely to deformwhen loaded in the toprack. Turn ProDry™ optionoff for an air dry.

Available with anycycle except Rinse

Only

Uses the heatingelement to heat air,plus a system ofvents and a fan thatventilates moist airout of thedishwasher tospeed drying times.ProDry™ optiondefaults to ONwhen any cycle isselected except for1 Hour Wash.

44 51 0

Dries dishes with heat.This option with the use ofrinse aid will provide thebest drying performance.Plastic items are less likelyto deform when loaded inthe top rack. Turn Heat Dryoff for an air dry.

Available with anycycle except Rinse

Only

Activates theheating element atthe end of the washcycle to speeddrying times. HeatDry defaults to ONwhen any cycle isselected except for1 Hour Wash.

52 52 0

Runs the dishwasher at alater time or during off-

peak electrical hours.Select a wash cycle andoptions. Press 4 HourDelay. Press START/ RESUME. Close the doorfirmly.

NOTE: Anytime the door isopened (such as, to add adish), the Start/Resumebutton must be pressedagain to resume the delaycountdown.

Available with anycycle

Delays the start of acycle up to 4 hours

240 240 0

OPTION SELECTIONS


WHAT IT DOES ADDED TIME TO CYCLE ADDEDWATERGALLONS(LITERS)

TYPICAL MAX



OEATION


C O D

Control Lock Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.To turn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The ControlLock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any buttonwhile your dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while thecontrols are locked.

NOTE: You may need to disable Sleep Mode by pressing either START/RESUME or CANCEL, or by opening andclosing the door before you are able to turn Control Lock off.

To turn off Control Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. Thelight turns off.

NOTE: If your model requires you to press and hold 4 HOUR DELAY to lock the controls, the Control Lock LED will beon or off to indicate if Control Lock is active or not.

CONTROLS AND CYCLE STATUS

CONTROL PURPOSE COMMENTS

To start or resume awash cycle

If the door is opened during a cycle or the power is interrupted, the Start/Resume indicatorflashes. The cycle will not resume until the door is closed and START/RESUME is pressed.

NOTE: If the Start/Resume button is located on top of door, push door firmly closed within3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds, theStart/Resume button LED will flash, an audible tone will be heard, and the cycle will notstart.

To reset any cycle oroptions duringselection.

To cancel a washcycle after it'sstarted.

Press and hold CANCEL/DRAIN to reset any control selections made.

See “Canceling A Cycle After Dishwasher Is Started” and “Changing A Cycle AfterDishwasher Is Started” sections.

To turn the audible

tones on or off.

Press and hold the Hi-Temp Scrub button for 3 seconds to turn the audible tones on or off.

Only audible tones for confirming button presses can be turned on/off. Important audibletones, such as indicating a cycle has been interrupted, cannot be deactivated.

OPTION SELECTIONS


WHAT IT DOES ADDED TIME TO CYCLE ADDEDWATERGALLONS(LITERS)

TYPICAL MAX

or




OEATION

CONTROLS AND CYCLE STATUS

CONTROL PURPOSE COMMENTS

The Cycle Status IndicatorLights are used to follow theprogress of the dishwasher

cycle. Located on the frontof the dishwasher for frontcontrol models, and locatedon the top of the door forhidden control models.

Clean indicator glows when a cycle is finished.

If you select the Sani Rinse option, when the Sani Rinse cycle is finished,the Sanitized indicator glows. If your dishwasher did not properly sanitizeyour dishes, the light flashes at the end of the cycle. This can happen if thecycle is interrupted, or the water could not be heated to the requiredtemperature.

The Clean and Sanitized lights go off when you open and close the door orpress and hold CANCEL.

The Front Indicator Light orSingle Exterior Light (A)shows progress of yourdishwasher cycle by color(for hidden control modelsonly).

The light will be blue if the dishwasher is washing or rinsing. The light willbe red when the dishwasher is drying. The light will be green to indicatethat the cycle is complete. If the Front Indicator Light is blinking, see“Troubleshooting” section.

The Cycle Status Display isused to follow the progressof the dishwasher cycle, andto show other information.(Available on some modelsinstead of Cycle StatusIndicator Lights)

The indicators will inform you if you are able to add a dish to the cycle afterit has started. It will also inform you if the dishwasher is washing, rinsing,drying, complete, and/or sanitized. They will show whether the control islocked and/or the delay option is selected. A series of bars will count downthe duration of the cycle remaining from left to right. Each bar equalsapproximately 24 minutes of cycle length. The bars will also count downthe delay feature from left to right, and the delay indicator will be activated.

A

D F S

Canceling A Cycle

1. Open the door slightly to stop the cycle. Wait for the sprayingaction to stop before completely opening the door.

2. Press and hold Cancel/Drain button once. The Cancel/Drainlight will light up.

3. Close the door and the dishwasher starts a drain cycle (if waterremains in bottom of dishwasher). Let the dishwasher draincompletely. The Cancel/Drain light turns off after 2 minutes.

Changing A Cycle After Dishwasher Is Started

1. You can interrupt a cycle and restart your dishwasher from thebeginning using the following procedure.

2. Open the door slightly to stop the cycle. Wait for the sprayingaction to stop, then open the door completely.

3. Check that detergent dispenser cover is still closed. If cover isopen, you will need to refill the detergent dispenser beforerestarting your new cycle.

4. Press and hold CANCEL/DRAIN twice to reset the control.

5. Select new cycles and options.

6. Press START/RESUME.

Adding A Dish After Dishwasher Is Started

1. Check if Add a Dish indicator is lit. (Available on some models.Otherwise, proceed to Step 2.)

2. Open the door slightly to stop the cycle. Wait for the sprayingaction to stop, and then open the door completely.

3. Check whether the detergent dispenser cover is still closed. Ifit is open, the wash cycle has already started and adding a

dish is not recommended.4. If detergent has not yet been used (detergent dispenser cover

is closed), you may add a dish.

5. Press START/RESUME.



OEATION


D F

Your KitchenAid dishwasher may have some or all of these features.

ProScrub® Option Wash Area

The ProScrub® option wash area is located at the back of the lowerlevel rack.

NOTE: You must select the ProScrub® option to use this feature.Make sure items do not interfere with the water feed tube, sprayarms, or ProScrub® spray jets.

■ Keep the last tine row in the back of the lower rack in the

60° angled position when using the ProScrub® option.

■ Load pans, casserole dishes, etc. in the back of the lower dishrack with the soiled surfaces facing the ProScrub® spray jets,and resting on the last row of tines in the angled position

■ Only one row of items may face the ProScrub® spray jets.Stacking, overlapping or nesting items will keep the ProScrub® spray jets from contacting all of the surfaces.

Silverware Basket

Use the slots in the covers tokeep your silverware separatedfor optimum wash. There arespecially designed slots (smallround holes) for chopsticks. Mixsilverware types to keep them

separated. Load knives down,forks up, and alternate spoons,for best cleaning results.

NOTE: If your silverwaredoes not fit into thedesignated slots, flip thecovers up and push themdown into the basket.

CULINARY CADDY ® Utensil Basket

Use the utensil basket to hold specialtycooking utensils (serving spoons,spatulas, and similar items), or overflowsilverware items.

The basket hangs on the bottom rack inthe right-hand corner. Load the basketwhile it is on the bottom rack or removethe basket for loading on a counter ortable.

NOTE: Spin the spray arms. Be sureitems in the basket do not stop the

rotation of the spray arms.

SURE-HOLD® Cup and Stemware Holder

Fold down the extra shelf on the left-hand or right-hand side of themid level rack to hold additional cups, stemware or long items suchas utensils and spatulas.

NOTE: Remove the culinary tool basket(s) when washing tallstemware or other tall items in the top rack.




OEATION

D F

FLEXI-FOLD DOWN™ Flexible Tines

The row of tines on the left-hand andright-hand sides of the top rack canbe adjusted to make room for avariety of dishes.

To adjust the fold-down tines:

1. Grasp the tip of the tine that is inthe tine holder.

2. Gently push the tine out of theholder.

3. Lay the tines down, toward thecenter of the rack.

NOTE: The bottom rack may also have 1 or 2 rows of flexible tineslocated in the back of the rack. Follow the same instructions toadjust.

SURE-HOLD® Light Item Clips

The light item clips hold lightweight plastic itemssuch as cups, lids, or bowls in place duringwashing.

To move a clip:

1. Pull the clip up and off the tine.

2. Reposition the clip on another tine.

Premium Adjustable 2-Position Top Rack

After removing the culinary tool rack, you can raise or lower the toprack to fit tall items in either the top or bottom rack. Adjusters arelocated on each side of the top rack. Each adjuster has 2 presetpositions.

To raise the rack, press both rack adjusters and lift the rack until itis in the Up position and level.

To lower the rack,press both rackadjusters and slide therack to its Downposition and level.

Removable Top Rack (for SatinGlide® rails)

The removable top rack allows you to wash larger items such aspots, roasters, and cookie sheets in the bottom rack.

IMPORTANT: Remove dishes prior to removing the top rack fromdishwasher.

To remove the rack

To gain access to the track stops, pull the upper rack forward

about halfway out of the tub.To open, flip the track stop toward the outside of the tub.

After opening both track stops, pull top rack out of the rails.

Removable Top Rack (for SatinGlide® Max rails)

The removable top rackallows you to wash largeritems such as pots, roasters,and cookie sheets in thebottom rack.

IMPORTANT: Removedishes prior to removing thetop rack from thedishwasher.

To remove the rack:

To gain access to theremovable tabs on thetracks/rails, pull the upperrack forward about halfway out of the tub.

On one side, press the tab on the track in and pull up the front endof the rack out of the track. Then repeat this step on the other sideto completely remove the front end of the rack.

Then remove the back end of the rack, by pulling the back end outwith a slightly forward, and then upward motion.

To replace the rack:Pull the tracks forward about halfway out of the tub.

Along the sides of the racks are round attachment tabs. Align therack's back end attachment tabs with the cutout in the track. Pushdown into place.

Pull the tracks completely out, and align the rack's front endattachment tabs with the cutout in the track. Push down into place.You will hear a snap when the front end of the rack is secured intoplace on each side.

Removable Culinary Tool Rack (3rd level rack)

The removable culinary tool rack(3rd level rack) allows you to washlarger items in the upper rack, orremove both the culinary tool rack

and top rack to wash larger timesin the lower rack. See “RemovableTop Rack” section.

To remove the rack:1. To access track stops, pull the

rack forward until it stops andclicks into place.

2. To open track stops, flip the track stop to the outside of thetrack.

3. After opening both track stops, slide front wheels up and outof the slot in track. Continue to pull rack forward in track andslide the back wheels up and out of the track.

4. Close track stops.

5. Slide rack tracks back into dishwasher.

To replace the rack:

1. Gently pull rack tracks forward in dishwasher until they stopand click into place.

2. To open track stops, flip the track stop to the outside of thetrack.

3. Place the back rack rollers on each side of the rack into thetrack slot and roll the rack back into the tracks.

4. Insert front rack rollers on each side of the rack into the rackslots.

5. Close track stops on both sides of rack and slide rack backinto dishwasher.

A. Track stop

B. Track

A

B

Track stop openTrack stop closed



OEATION


D F

Culinary Tool Rack (3rd level rack)

The culinary tool rack is designed with 2 movable baskets to holdextra silverware, knives and cooking utensils.

Install the baskets in this up position when you have extrasilverware and flatware to wash.

Install the baskets in this down position when you have extrasilverware, knives, or utensils requiring more room to wash.

IMPORTANT: When you are using the culinary tool baskets in thedown position, the top rack must also be in the lowest position.

Remove the front basket in the down position, when you are usingthe cup shelves or other tall items in the top rack for more room.

Filtration SystemYour dishwasher has the latest technology in dishwasher filtration. This triple filtration system minimizes sound and optimizes water andenergy conservation while providing superior cleaning performance. Throughout the life of your dishwasher, the filter will require

maintenance to sustain peak cleaning performance.

Up position

Down position

The triple filter system consists of 2 parts, an upper filterassembly and a lower filter.

■ The upper filter assembly keeps oversized items andforeign objects, along with very fine food particles, out ofthe pump.

■ The lower filter keeps food from being recirculated ontoyour dishware.

The filters may need to be cleaned when:

■ Visible objects or soils are on the upper filter assembly.

■ There is degradation in cleaning performance (that is,soils still present on dishes).

■ Dishes feel gritty to the touch.

It is very easy to remove and maintain the filters. The chartbelow shows the recommended cleaning frequency.

Upper Filter

Assembly

Lower Filter

P U S H

DOWN &T U R N

L O C K U

N L O

C K

F S




OEATION

F S

*Manufacturer's recommendation: This practice will conserve the water and energy that you would have used to prepare your dishes. Thiswill also save you time and effort.

Very Hard Water

If you have hard water (above 15 grains), clean your filter at leastonce per month. Building up of white residue on your dishwasherindicates hard water. For tips on removing spots and stains, see“Troubleshooting” section.

Cleaning Instructions

IMPORTANT: Do not use wire brush, scouring pad, etc., as they

may damage the filters.

Rinse filter under running water until most soils are removed. If youhave hard-to-remove soils or calcium deposits from hard water, asoft brush may be required.

IMPORTANT: To avoid damage to dishwasher, do not operate yourdishwasher without the filters properly installed. Be sure the lowerfilter is securely in place and the upper filter assembly is locked intoplace. If the upper filter assembly turns freely, it is not locked intoplace.

RECOMMENDED TIME INTERVAL TO CLEAN YOUR FILTER

Number of LoadsPer Week

If you washbefore loading

If you scrape and rinsebefore loading

If you only scrapebefore loading*

If you do not scrape or rinsebefore loading

1-3 Once per year Once per year Twice per year Every two months

4-7 Once per year Once per year Twice per year Once per month

8-12 Once per year Twice per year Every three months Every two weeks

13-14 Once per year Twice per year Every three months Once per week

Filter Removal Instructions

1. Turn the upper filter

assembly ¹ ⁄ ₄ turncounterclockwise and liftout.

2. Grasp the lower filter in thecircular opening, liftslightly, and pull forward toremove.

3. Clean the filters as shownbelow.

To remove upper filter assembly

L O C K

UNLOC K

PUSH DO W N & T U R N

P U S H

D O W N & T U R N

L O C K

U N L O C K

Filter Reinstallation Instructions

1. Noting the previousillustrations, place thelower filter under thelocating tabs in the bottomof the dishwasher so theround opening for theupper filter assembly linesup with the round openingin the bottom of the tub.

To replace upper filter assembly

2. Insert the upper filter assembly into the ci rcular opening inthe lower filter.

3. Slowly rotate the filter clockwise until it drops into place.Continue to rotate until the filter is locked into place. If thefilter is not fully seated (still turns freely), continue to turnthe filter clockwise until it drops and locks into place.

NOTE: The upper filter assembly arrow does not have to

align with the arrow in the lower filter as long as the filter islocked.

L O C

K

U N LO CK

P U S H D O W N

&

T U R

N



OEATION


D C

Cleaning

Drain Air Gap

Storing

Cleaning the exterior

In most cases, regular use of a soft, damp cloth or sponge and a mild detergent is allthat is necessary to keep the outside of your dishwasher looking nice and clean. If yourdishwasher has a stainless steel exterior, a stainless steel cleaner is recommended.

Cleaning the interior Hard water minerals can cause a white film to build up on the inside surfaces, especially just beneath the door area.

Do not clean the dishwasher interior until it has cooled. You may want to wear rubbergloves. Do not use any type of cleanser other than dishwasher detergent because it maycause foaming or sudsing.

To clean interior

Make a paste with powdered dishwasher detergent on a damp sponge and clean.

OR

Use liquid automatic dishwasher detergent and clean with a damp sponge.

OR

See the vinegar rinse procedure in “Cloudy or Spotted Dishware (and Hard WaterSolution)” in “Troubleshooting” section.

NOTE: Run a normal cycle with dishwasher detergent after cleaning the interior.

Some state or local plumbing codes require the addition of a drain air gap between abuilt-in dishwasher and the home drain system. Check the drain air gap when yourdishwasher is not draining well.

The drain air gap is usually located on top of the sink or countertop near the dishwasher.

NOTE: The drain air gap is an external plumbing device that is not part of your

dishwasher. The warranty provided with your dishwasher does not cover service costsdirectly associated with the cleaning or repair of the external drain air gap.

To clean the drain air gap Clean the drain air gap periodically to ensure proper drainage of your dishwasher. Withmost types, you lift off the chrome cover. Unscrew the plastic cap. Then check for anysoil buildup. Clean if necessary.

Storing for the summer If your dishwasher is not in use during the summer months, turn off the water supply andpower supply to the dishwasher.

Storing for the winter Avoid possible water damage to your home and dishwasher due to freezing water lines.If your dishwasher is left in a seasonal dwelling or could be exposed to near freezingtemperatures, have your dishwasher winterized by authorized service personnel.




OEATION

C T GFirst try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.In the U.S.A., www.kitchenaid.com In Canada, www.kitchenaid.ca

PROBLEM SOLUTION

DISHWASHER DOESNOT RUN

NOTE: It is normal for the dishwasher to repeatedly pause several times during a cycle.

If the Start/Resume light is blinking, close the door and push START/RESUME.

Be sure the door is closed and latched.

Be sure you have disabled Sleep Mode by pressing either START/RESUME or CANCEL, or openingand closing the door before selecting your cycle/option.

Check that there is not an interference with large casserole dishes and the wash system at the backof the dishwasher. Adjust loading as necessary to ensure door is closed and latched.

Be sure you have selected a cycle. (See “Cycles and Options Descriptions” section.)

Be sure there is power to the dishwasher. A circuit breaker or fuse may have tripped.

If lights other than Start/Resume blink and the unit will not run, you will need to call for service.

DETERGENT REMAINS INTHE DISPENSER ORTABLET IS ON BOTTOMOFTUB

Check for dishware such as cookie sheets, cutting boards, or large containers, etc., that may beblocking the detergent dispenser from opening properly.

Be sure your detergent is fresh and lump free.

Be sure the cycle has completed (the Clean light is on). If it has not completed, you will need toresume the cycle by closing the door and pressing START/RESUME.

CYCLE RUNS TOO LONG NOTES:

■ To use less water and reduce energy consumption you will encounter cycles that typically run forup to 3 hours.

■ A water heater setting of 120°F (49°C) is best, the dishwasher will delay longer while heatingcooler water.

■ Some options will add time to the cycle. (See “Cycles and Options Descriptions” section.) TheProDry™ or Heat Dry option adds approximately ¹ ⁄ ₂ hour.

Try the 1 Hour Wash cycle.

Run the hot water at a faucet close to the dishwasher before starting the cycle.

DISHWASHER NOT DRYING NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a poroussurface which tends to collect water droplets. Towel drying may be necessary.

Use of rinse aid along with the ProDry™ or Heat Dry option is needed for proper drying.

Proper loading of items can affect drying. (See specific loading instructions within this guide.)

Glasses and cups with concave bottoms hold water. This water may spill onto other items whenunloading.

■ Unload the bottom rack first.

■ Locate these items on the more slanted side of the rack for improved results.

WILL NOT FILL Be sure the water is turned on to the dishwasher.

Check that the float is free from obstructions. (See “Parts and Features.”)

Check for suds in the dishwasher. If foam or suds are detected, the dishwasher may not operateproperly or may not fill with water. (See “Blinking Lights” in “Troubleshooting” section.)

WATER REMAINS IN THETUB/WILL NOT DRAIN

Be sure the cycle has completed (the Clean light is on). If it has not, you will need to resume the cycleby closing the door and pressing START/RESUME.

If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removedfrom the disposer inlet.

Check for kinks in the drain hose.

Check for food obstructions in the drain or disposer.

Check your house fuse or circuit breaker.

HARD WATER(WHITE RESIDUE ONDISHWASHER INTERIOR ORGLASSWARE)

NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make itdifficult to achieve good cleaning. A water softener is strongly recommended if your hardness is15 grains or more. If a water softener is not installed, the following steps may help:

Use a commercial cleaner designed for dishwashers once per month.

Clean the upper and lower filters at least once per month. (See “Cleaning Instructions” in the“Filtration System” section.)

Always use a rinse aid.

Always use a high-quality, fresh detergent.

Use a detergent booster/water softener additive designed for dishwashers.



OEATION


ODORS NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load daily until afull load is ready to run, or use the Top Rack Only option (on some models) for partial loads.

Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an uprightglass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option turned off. Donot use detergent.

The dishwasher may not be draining properly, see “Water Remains In The Tub/Will Not Drain” in the“Troubleshooting” section.

NOISY NOTES:■ Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.

■ Normal water valve hissing may be heard periodically.

■ A normal snap sound may be heard when the detergent dispenser opens during the cycle andwhen the door is opened at the end of the cycle.

■ Improper installation will affect noise levels.

Be sure the filters are properly installed.

A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms.Readjust the dishware and resume the cycle.

FOOD SOILS REMAINON DISHES

Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washingperformance (see “Dishwasher Use” section).

Check filter to ensure it is properly installed. Clean it if needed. (See “Cleaning Instructions” in the“Filtration System” section for details.)

Select the proper cycle and option for the type of soils. The ProWash™ or the Heavy Duty cycle with

the ProScrub®

(on some models) option can be used for tougher loads.Be sure the incoming water temperature is at least 120°F (49°C).

Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads andhard water conditions.

Scrape food from dishes prior to loading (do not prerinse).

DISHES DIRTY/SUDS INDISHWASHER/CYCLE NOTCOMPLETE

If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operateproperly or may not fill with water.

Suds can come from:

■ Using the incorrect type of detergent, such as dish detergent for hand washing dishes, laundrydetergent, or hand soap.

■ Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.

■ Using an excessive amount of dishwasher detergent.

Call for service.

If no water was present in the machine at any time during a heated wash cycle, the cycle will end and

the Clean LED will not come on. See “Will Not Fill” in the “Troubleshooting” section.

DID NOT SANITIZE If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final rinse,or the temperature for your water heater is set too low. Set your water heater to 120ºF (49°C).

DAMAGE TO DISHWARE Improper loading can cause dishes to become chipped or damaged. (See specific loadinginstructions within this guide.)

BLINKING LIGHTS Blinking LED's will occur when the cycle is paused or when the cycle has been interrupted byopening the door. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s), andthe countdown bars on the Cycle Status Display all blink together to indicate that attention isneeded. See “Start or Resume a Cycle” in the “Dishwasher Use” section.

Blinking LED's can also occur when certain errors have been detected. In this case, the Clean/ Complete LED will blink 4 times in a row with a pause in between each set of blinks. When this erroroccurs, the controls will lock out and not allow another cycle to be started.

Call for service.

CLOUDY OR SPOTTEDDISHWARE (AND HARDWATER SOLUTION)

NOTES:

■ Liquid rinse aid is necessary for drying and to reduce spotting.

■ Use the correct amount of detergent.

Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If thecloudiness disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. See“Hard Water (White Residue On Dishwasher Interior Or Glassware)” in the “Troubleshooting” section.If it does not come clear, it is due to etching (see below).

Be sure the incoming water temperature is set at 120°F (49°C).

Try using the High Temp and Sani Rinse options.

To remove spotting, run a vinegar rinse through the dishwasher.

■ Wash and rinse the affected dishware and load into dishwasher. Remove all silverware and metalitems. Put 2 cups (500 mL) of white vinegar in a glass measuring cup in the lower rack. Run anormal cycle with the Heat Dry option turned off. No detergent is needed.

PROBLEM SOLUTION




OEATION

ETCHING (PERMANENTCLOUDINESS)

This is an erosion of the surface of the glassware and can be caused by a combination of: water thatis too hot, from using too much detergent with soft water or by pre-washing. Detergent needs foodsoil to act upon. If etching has occurred, the glassware is permanently damaged. To avoid furtheretching, adjust the detergent amount to match the water hardness, stop pre-washing, and use waterheating options only when incoming water temperature is below 120°F (49°C).

LEAKING WATER Be sure dishwasher has been installed properly and is level.

Suds can cause the dishwasher to overflow. Measure the detergent accurately and use only

detergents designed for use in a dishwasher. Less detergent is needed in soft water. Try anotherbrand of detergent if sudsing continues.

To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached and avoidoverfilling.

TUB IS DISCOLORED NOTES:

■ High iron content in the water can discolor the tub.

■ Tomato-based foods can discolor the tub or dishware.

■ A citrus-based cleaner can be used to clean.

PROBLEM SOLUTION

N



INSTALLATION


S I

s so ros sllo rrs rorsor KA lss l ll Dssr

■ Dssr

■ Isllo rs

■ oo rs

■ Dr rs

■ Wr l rs

■ lrl rs

■ Isllo Isros

■ Isll Cso l

■ C Oro

■ Aol s

■ os




INSTALLATION

D S

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don'tfollow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IOTANT SAFET INSTUCTIONSANIN W s ssr ollo s ros l ollo

■ ll sros or s ssr

■ s ssr ol or s o

■ s ol rs or rs s ro ors ssr o o r olr

■ W lo s o s

1 o sr s so r o ll o

oor sl 2 o sr s ls o r

rs o - rs

■ Do o s ls s lss r rssr s or l or ls s oso r rrs roos

■ Do o o l r or lr s

■ Do o or ssr lss ll losrls r rorl l

■ Do o r orols

■ Do o s s o or s o oor l or srs o ssr

■ o r rs o r o o llo lr o l or o ssr

■ r r oos ro s ro o r ss s o s or o

s or or DO A I OI I or ss s o s or s ro ors ssr r o ll o r s l r o ro or srl s sll rls l ro s As s sl o o so or s o rs

■ o oor or l o s or ro ol ssr ro sr orsr


o Clor rooso 5 Wrs

ANIN s ro os o or or ls o o o Clor o s r

ANIN s ro os o or or ls o o o Clor o s r s or or

rro r



INSTALLATION


D S

Isll r ssr s slr ro lsAo ossl rr o ll l ro r rrs r o or rr orso or r sor oro

Isll ll ssr o oor ll ol r sl or s s s

o ll s ls ro oss oorss s o r ol or sll Isllo Isros or ol oro

OUNDIN INSTUCTIONS

Fr a rune, rnnete ishwasher ssr

s ro I o lo orro ro ll r rs o lrso ro o ls rss or lrrr ssr s or -ro oor ro l l s l o ror ol s sll ro or ll lolos orsANIN Iror oo o -ro oor rsl rs o lr soC l lr or sr rrs o r o r ssr s rorlro Do o o l ro ssr ll o ol ror olsll l lr

Fr a eranentl nnete ishwasher ssrs o o ro l rr ss or -ro oor s r r oors o o -ro rl or l o ssr


Tip Over Hazard






Connect ground wire to green ground connector

in terminal box.Do not use an extension cord.

Failure to follow these instructions can result indeath, fire, or electrical shock.




INSTALLATION

I R

Tools and PartsGather the recommended tools and parts before startinginstallation. Read and follow the instructions provided with anytools listed here.

All InstallationsTools needed:

*Must be the proper size to connect your household wiring to 16-gauge wiring in dishwasher.

Other useful items you may need:

Parts supplied:

Parts needed:

4 #10 x ¹ / ₂" wood screws (if installing custom front panels)

Supplied in Kit:4 Plastic studs (attached to each other by runners)

4 Short screws (10-16 hex head screw)

4 Long screws (8-18 Torx® head screws)

1 Template (located inside Use and Care Guide bag assembly)

1 Instruction sheet (located inside Use and Care Guide bagassembly)

NOTE: The screws supplied are used for only ³ ⁄ ₄" thick woodenpanel. If the wooden panel is less than ³ ⁄ ₄" thick, customer mustpurchase screws locally.

Other parts you may also need:

NOTES:

■ Moisture barrier tape is recommended when installing adishwasher under a wood countertop.

■ Parts available for purchase in plumbing supply stores. Checklocal codes. Check existing electrical supply. See “ElectricalRequirements” section. It is recommended that electricalconnections be made by a licensed electrical installer.

In addition, for first-time installationsTools needed:

Parts needed:

Additional parts supplied with top-venting models only:

Additional parts supplied with certain models only

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-422-1230.

® O 20 r rsr rrs o r srs I



INSTALLATION


Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where theycan interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provideclearance between motor and flooring. Motor should not touchthe floor.

Do not install dishwasher over carpeted flooring.Shelter dishwasher and water lines leading to dishwasher againstfreezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing yourdishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is availablefrom your dealer for installing underneath the countertop.Call 1-800-422-1230 to order.

Check location where dishwasher will be installed. The locationmust provide:

■ easy access to water, electricity and drain.

■ convenient access for loading and unloading dishes.Corner locations require a 2" (5.1 cm) minimum clearancebetween the side of the dishwasher door and the wall or

cabinet.■ square opening for proper operation and appearance.

■ cabinet front perpendicular to floor.

■ level floor. (If floor at front of opening is not level with floorat rear of opening, shims may be needed to leveldishwasher.)

Helpful Tip: Be sure to accurately measure dimensions andensure dishwasher is level if the floor in the dishwasher opening isuneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims mustbe securely attached to the floor.

If dishwasher will be left unused for a period of time or in alocation where it may be subject to freezing, have it winterized byauthorized service personnel.

Make sure pipes, wires and drain hose are within the shaded areashown in the “Product and Cabinet Opening Dimensions” section

L R




INSTALLATION



INSTALLATION


Drain Requirements■ A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with amaximum length of 12 ft (3.7 m) (Part Number 3385556) thatmeets all current AHAM/IAPMO test standards, is resistant toheat and detergent, and fits the 1" (2.5 cm) drain connector ofthe dishwasher.

■ Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm)minimum above the floor. It is recommended that the drainhose either be looped up and securely fastened to theunderside of the counter, or be connected to an air gap.

■ Make sure to use an air gap if the drain hose is connected tohouse plumbing lower than 20" (50.8 cm) above subfloor orfloor.

■ Use ¹₂" minimum I.D. drain line fittings.

■

If required, the air gap should be installed in accordance withthe air gap installation instructions. When you are connectingthe air gap, a rubber hose (not provided) will be needed toconnect to the waste tee or disposer inlet.

Water Supply Requirements■ A hot water line with 20 to 120 psi (138 to 862 kPa) water

pressure can be verified by a licensed plumber.

■ 120°F (49°C) water at dishwasher.

■ ³ ⁄ ₈" O.D. copper tubing with compression fitting or flexiblebraided water supply line (Part Number 4396897RP).NOTE: ¹ ⁄ ₂" minimum plastic tubing is not recommended.

■ A 90° elbow with ³ ⁄ ₄" hose connection with rubber washer.

■ Do not solder within 6" (15.2 cm) of the water inlet valve.

Electrical RequirementsBe sure that the electrical connection and wire size are adequateand in conformance with the National Electrical Code, ANSI/NFPA70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association1 Batterymarch ParkQuincy, MA 02169-7471

You must have:

■ 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electricalsupply.

■ Copper wire only.

We recommend:

■ A time-delay fuse or circuit breaker.

■ A separate circuit.

If connecting dishwasher with apower supply cord:■ Use UL Listed power supply cord kit

(Part Number 4317824) marked foruse with dishwasher.

■ Power supply cord must plug into a grounded3 prong outlet, located in the cabinet next tothe dishwasher opening. Outlet must meet alllocal codes and ordinances.

If connecting dishwasher with direct wiring:■ Use flexible, armored or nonmetallic

sheathed, copper wire withgrounding wire that meets thewiring requirements for your homeand local codes and ordinances.

■ Use a UL Listed/CSA Approved strain relief.




INSTALLATION

I I

Prepare Cabinet Opening—ExistingUtilities

If the water line and the cable extend to the locations shown,

proceed to the “Install Drain Hose” section. If they do not reach faenough, follow the instructions in the “Prepare Cabinet OpeningNew Utilities” section.

Prepare Cabinet Opening—New Utilities

Prepare and route the electrical supply

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet nexto the dishwasher cabinet opening.

Drill a 1¹ ⁄ ₂" (3.8 cm) hole in cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

WARNING

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.




INSTALLATION


Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet included with powersupply cord kit.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route thecable into the cabinet opening from the right-hand side.

Drill a 1¹ ⁄ ₂" (3.8 cm) hole in right-hand cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797 -not provided).

Route cable from power supply through cabinet hole (cable mustextend to the right front side of cabinet opening). Tape cable tothe floor in area shown. This will prohibit cable from moving whendishwasher is moved into cabinet opening.

Prepare and Route Water LineHelpful Tip: Routing the water line through the left side of cabineopening will make water connection easier.

Drill a ¹ ⁄ ₂" (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing for the water supply line




INSTALLATION

Attach the water supply line (copper tubing or flexible braided line)to the hot water line using a connection configuration that is incompliance with local codes and ordinances. The water supply tothe dishwasher should have a manual shutoff valve located underthe sink.

Slowly route water supply line through hole in cabinet. (If you areusing copper tubing, it will bend and kink easily, so be gentle.) Itshould be far enough into the cabinet opening to connect it to thedishwasher inlet on the front left side of the dishwasher.

Slowly turn water shutoff valve to “ON” position. Flush water intoa shallow pan until clear to get rid of particles that could clog theinlet valve. Turn shutoff valve to “OFF” position.

Route water line and tape it to the floor in area shown. This willkeep it from moving when dishwasher is moved into cabinetopening.

Install Drain HoseIMPORTANT: Always use a new drain hose. Check local codes todetermine whether an air gap is required.

If needed, drill a 1¹ ⁄ ₂" (3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the frontcenter of opening where drain connection will be made. Tapedrain hose to the floor in area shown. This will prohibit it frommoving when dishwasher is moved into cabinet opening.



INSTALLATION


IMPORTANT: The drain hose connection of the disposer or awaste tee must be made before the drain trap and at least20" (50.8 cm) above the floor where the dishwasher will beinstalled.

Helpful Tip: To reduce vibration of the hose, keep the hose awayfrom the floor.

Option A, Waste disposer – no air gap

Option B, No waste disposer – no air gap

Option C, Waste disposer – with air gap

1. Using a hammer and screwdriver,knock plug into disposer.

2. Use needle-nose pliers to removeplug.

3. Attach drain hose to disposer inletwith large drain hose clamp(provided). Use pliers to squeezeclamp open and move into position.

1. Fit rubber end of drain hose to wastetee and cut if needed.NOTE: Do not cut ribbed section.

2. Attach rubber end of drain hose towaste tee with a large drain hoseclamp (provided). Use pliers tosqueeze clamp open and move intoposition. If the drain hose was cut,use a 1¹ ⁄ ₂" to 2" (3.8 to 5 cm) screw-type clamp (not provided).

1. Using a hammer and screwdriver,knock plug into disposer.

2. Use needle-nose pliers to removeplug.

3. Connect rubber end of drain hose toair gap and cut if needed.NOTE: Do not cut ribbed section.

4. Attach drain hose to air gap withlarge drain hose clamp (provided).Use pliers to squeeze clamp openand move into position. If the drainhose was cut, use a 1¹ ⁄ ₂" to 2" (3.8 to5 cm) screw-type clamp (notprovided).

5.Use a rubber hose (not provided)with screw-type clamps (notprovided) to connect from air gap todisposer inlet.




INSTALLATION

Option D, No waste disposer – with air gap

Install Moisture Barrier(under a wood countertop)

. Make sure the area under the cabinet is clean and dry forinstallation of the moisture barrier.

. Remove the backing of the moisture barrier and apply tounderside of the countertop along the front edge of thecounter.

Prepare Dishwasher

Helpful Tip: Place cardboard under dishwasher until installed incabinet opening to avoid damaging floor covering. Do not usedoor panel as a worktable without first covering with a towel toavoid scratching the door panel.

Using 2 or more people, grasp sides of dishwasher door frameand place dishwasher on its back.

1. Connect rubber end of drain hose toair gap and cut if needed.NOTE: Do not cut ribbed section.

2. Attach drain hose to air gap with

large drain hose clamp (provided).Use pliers to squeeze clamp openand move into position. If the drainhose was cut, use a 1¹ ⁄ ₂" to 2" (3.8 to5 cm) screw-type clamp (notprovided).

3. Use a rubber hose (not provided)with screw-type clamps (notprovided) to connect from waste teeto air gap.

WARNING

Tip Over Hazard




WARNING

Excessive Weight Hazard

Use two or more people to move and installdishwasher.

Failure to do so can result in back or other injury.



INSTALLATION


Option A, Remove Access Panel - Plastic Panel

Using a flat-blade screwdriver, turn the plastic fasteners ¹ ⁄ ₄ turncounterclockwise to unlock them. Remove panel. Do not removetech sheet from access panel.

Option B, Remove Access Panel - Metal Panel

Using a ¹ ⁄ ₄" hex head socket, nut driver or Phillips screwdriver,remove 2 screws attaching access panel and lower panel todishwasher. Do not remove tech sheet from access panel.

Using a ¹ ⁄ ₄" hex head socket, nut driver or Torx®† T20® screwdriver,remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screwheads are facing to the left when tightening conduit nut. Strainrelief is provided with the power supply cord kit.

NOTE: If using Option B, proceed to “Determine CabinetOpening,” to continue with the installation of your dishwasher.

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lowerpart of dishwasher tub. Pull cord through strain relief in terminalbox.

Select UL Listed/CSA Approved twist-on wire connectors rated toconnect your power supply cord to 16-gauge dishwasher wiring.




INSTALLATION

Remove the green grounding screw and place through the ringterminal of the green ground wire. Reattach and tighten the greenscrew.

NOTE: Do not pre-twist stranded wire. Twist on wire connector.Gently tug on wires to be sure both are secured.

Connect wires black to black and white to white, using UL Listed/ CSA Approved twist-on wire connectors (included with powersupply cord kit).

If needed, see website for animated representation of this step. Visit www.kitchenaid.com/electrical under FAQ tab.

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs on left side of cover.Make sure wires are tucked inside box. Close cover ensuringwires are not pinched. Use ¹ ⁄ ₄" hex head socket, nut driver or Torx® T20® screwdriver and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

WARNING



Connect ground wire to green ground connector interminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,fire, or electrical shock.



INSTALLATION


Determine Cabinet Opening

Measure height of cabinet opening from underside of countertopto floor where dishwasher will be installed (you will need tomeasure the lowest point on the underside of the countertop andthe highest point on the floor). Refer to “Dishwasher Height

Adjustment Chart” for wheel position and the number of turnsneeded.

NOTE: If the minimum cabinet opening height is less than 34"(86.4 cm), the rear wheels can be removed for additionalclearance. This will allow the dishwasher to fit into a 33⁷ ⁄ ₈" (86 cm)high cabinet opening, but the dishwasher will be more difficult tomove. (Measurements are approximate. Wheels and legs arepreset at the factory for 34¹ ⁄ ₂" [87.6 cm].) If the minimum cabinetopening height is 33³ ⁄ ₄" (85.7 cm), a section in the insulationblanket can be removed by cutting along the perforation.

Turn both leveler legs to the same height. Put wheels in therequired position determined from “Dishwasher Height

Adjustment Chart.”

Built-up floors: If the kitchen floor is higher than the cabinetopening's floor - for example, the kitchen floor tile does notextend into the cabinet opening - add shims as needed in the areashown to bring the dishwasher up to 34" (86.4 cm) below thecountertop.

NOTE: Shims must be securely attached to floor to avoidmovement when the dishwasher is in use.




INSTALLATION

Install Door Handle(on some models)

IMPORTANT: Do not scratch the front panel during thisprocedure.

Remove the door handle and hardware bag containing thesetscrews and hex key from the cardboard box. Setscrews arelready installed in the handle. Place handle on mounting studs

ith the setscrews facing down. Push the door handle tightlygainst the door. Insert the short end of the hex key into the

setscrews. Tighten the setscrews ¹ ⁄ ₄ turn past snug.

Retain hex key with Installation Instructions.

Custom Panel Dimensions

Install Custom Panel

Follow steps below: A customer supplied panel must weigh no more than 16 lbs(7.3 kg) and must be made to specific dimensions. It isrecommended that a cabinetmaker cut the customer panelbecause of the precise dimensions needed.

NOTES:

■ The handle for the custom panel is not included.

■ All mounting hardware supplied is for a ³ ⁄ ₄" (19.1 mm) thickwood panel. If a thinner wood panel or materials other thanwood are used, it is the customer’s responsibility to obtain theproper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both sides andall edges of the panel to avoid damage from moisture.

Using 2 or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

WARNING






INSTALLATION


Install the custom hardware handle(s) on the front of the woodenpanel inside dotted line.

IMPORTANT: If the handle is attached from the back of thecustom panel, the screw holes should be countersunk for thescrews heads to be flush with the panel. If the handle is attachedto the front of the custom panel, the screw lengths cannot exceedthe panel thickness.

Using the template provided, attach it to the backside of thecustom panel with tape. Make sure that the center of the template

is aligned with the center of the wooden panel and top of thetemplate is aligned to the top face of the wooden panel.

NOTE: Do not drill deeper then ⁵ ⁄ ₈" (16 mm) to keep from drillingthrough panel. Pilot hole depths given are for ³ ⁄ ₄" (19 mm) thickpanel.

Mark 4 pilot holes on the wooden panel using the templateprovided. Predrill 4 pilot holes using a ³ ⁄ ₃₂" drill bit. Use tape tomark the drill bit to gauge hole depth. Drill pilot holesapproximately ⁵ ⁄ ₈" (16 mm) into the custom panel.

A ls ss o oo ls sor srs ro




INSTALLATION

Check custom tape alignment with metal door slots; verify tape isright-side up, and that the tape does not overhang the metal dooron the top, bottom or side interfaces. Remove the backing fromthe custom tape by pulling straight down on the liner. Align thecustom tape to the keyhole slots on the metal door (see image)and apply. Repeat steps for one side and then the other.

NOTE: The adhesive on the tape is aggressive, so properalignment and attachment to the metal door needs to occur onthe first try.

Align the studs on the custom wood panel to the keyhole slots onthe door assembly. Ensure that all 4 plastic studs are engaged inthe keyhole slots. Slide wood panel down until the top surface ofthe wooden panel is flush with the top of the door.

Open the door and align top edges. Predrill 2 pilot holes using a³ ⁄ ₃₂" drill bit. Use tape to mark the drill bit to gauge hole depth. Drillpilot holes approximately 1¹ ⁄ ₂" (3.8 cm) into the top corners of thedoor using hole in liner as a guide.

Install 2 long screws supplied in top corners to secure customwood panel in place.

Remove the short screws (3rd from top) on either side of the innerdoor panel. Predrill 2 pilot holes using a ³ ⁄ ₃₂" drill bit. Use tape tomark the drill bit to gauge the hole depth. Drill pilot holesapproximately 1¹ ⁄ ₂" (3.8 cm) using the door liner hole as a guideinto the panel. Install the 2 remaining long screws.



INSTALLATION


Choose Attachment Option

Use 2 or more people to move and install dishwasher.

IMPORTANT: The dishwasher must be secured to the cabinet.There are two brackets found in the parts bag. Attach thebrackets using Option A if the countertop is wood, laminate oranother similar surface. If your countertop is marble, granite oranother hard surface, install using Option B.

Option A, Countertop attachment:

Remove the brackets from the package and insert into the openslots on the left and right-hand top of the dishwasher collar asshown.

Using a pair of pliers, bend the tab down to secure the bracket inplace. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option B, Dishwasher side attachment:

NOTE: Remove the brackets from the parts package.

Break off the end of the bracket along the scored line.

With another person holding the rear of the dishwasher to keep itfrom tipping, open dishwasher door and place towel over pumpassembly and spray arm of dishwasher. This will keep screwsfrom falling into pump area when you are securing dishwasher tocabinet.

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher isinstalled.

Push bracket into slot on the side of dishwasher, and bend tab intoward the side of the dishwasher so that it keeps the bracket inplace. Repeat this step for the other side of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

WARNING







INSTALLATION

Prepare Water Supply Line

Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm) ontocopper tubing.

NOTE: To avoid vibration during operation, route the water supplyline so that it does not touch the dishwasher base, frame or motor.

Connect the ³ ⁄ ₈" compression fitting to the water supply line priorto installing the unit into the cabinet opening. Attach such that the³ ⁄ ₄" connection is facing upward as shown above.

Copper tubing only: Put the tubing into the 90° elbow fitting as faras it will go (the copper tubing bends and kinks easily). Slide thenut and ferrule forward and start the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using ⁵ ⁄ ₈" openended wrench or adjustable wrench.

NOTE: Do not use Teflon®† tape with compression fittings.

Move Dishwasher Close to CabinetOpening

Use 2 or more people to move and install dishwasher.

IMPORTANT: Double-check correct placement of utilities. Graspthe sides of the dishwasher at the edges of the door panel. Tiltdishwasher backward on wheels and move dishwasher close tocabinet opening.

NOTE: Do not push on the front of the panel or on the console.

Panel or console may dent.Helpful Tip: Temporarily tape utilities to the floor in the locationsshown to prohibit them from moving when dishwasher is movedinto the cabinet opening.

Check that water line is on the left side of opening and drain hoseis near the center of the cabinet opening.

With another person holding the dishwasher to keep it fromtipping, open and close the door a few times. If the door closes orfalls open under its own weight, the door tension will need to beadjusted.

WARNING






INSTALLATION


To adjust the door spring tension, unhook the spring from the rearleg of dishwasher.

Using a ⁵ ⁄ ₁₆" nut driver or hex socket, remove the screw from thetensioner.

The screw can be put into one of 3 holes (1, 2, 3) in the front leg of

dishwasher. If the door closes by itself, move the tensioner to alower-numbered hole and replace screw. Reattach door spring torear leg.

NOTE: Tensioners on both sides of dishwasher should be securedat same holes.

When door is unlatched, if door opens by itself, move thetensioner to a higher-numbered hole and replace the screw.Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be securedat same holes.

IMPORTANT: If wheels were removed, cover the floor whenmoving the dishwasher. Slowly move dishwasher completely intocabinet opening. Do not kink or pinch water line, drain hose,power supply cord or direct wire between dishwasher andcabinet. Remove cardboard from under dishwasher.

NOTES:

■ It is all right if dishwasher fits tightly into cabinet opening. Do

not remove insulation blanket – the blanket reduces the soundlevel.

■ If using power cord, make sure to route end through hole incutout before sliding dishwasher into cabinet opening.

■ For models with water softener, make sure that the drain hosestays on the hanger that is on the right-hand side and istucked in on the side of the unit.

Align front of dishwasher door panel with front of cabinet doors.You may need to adjust alignment to be even with your cabinets.




INSTALLATION

Check that leveling legs are firmly against the floor. Close andlatch the door, and place level against the front panel. Check thatdishwasher is centered from front to back in the opening. Ifneeded, adjust leveling leg until dishwasher is plumb. Repeat forother side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasheroff the ground to adjust front legs. With some installations, it maybe easier to adjust the front leg using the ³ ⁄ ₁₆" hex head socket or

adjustable wrench.

Place level against top front opening of tub. Check thatdishwasher is level from side-to-side. If dishwasher is not level,adjust front legs up or down until dishwasher is level.

Connect to Water Supply

Be sure rubber washer is properly seated in fitting. Slide the³ ⁄ ₄" fitting up to the valve and hand tighten to avoid cross-threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An additional¹ ⁄ ₄ to ¹ ⁄ ₂ turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Place paper towel under 90° elbow fitting. Turn on water supplyand check for leaks. If leak occurs, repeat previous step.

If needed, see website for animated representation of this step. Visit www.kitchenaid.com/watersupply under FAQ tab.

NOTE: Do not use Teflon®† tape with compression fittings.

Connect to Drain

Place towel under drain hose to catch any water in drain hose.Place the small drain hose clamp onto the small end of the drainhose. Push the new drain hose into the black drain hoseconnector up to the drain hose stop.

O s rsr rr o I D o D ors Co



INSTALLATION


Using pliers, squeeze open the small drain hose clamp and slideonto connector between stops.

After hose is connected, remove towel.

If needed, see website for animated representation of this step. Visit www.kitchenaid.com/drain under FAQ tab.

Make Direct Wire Electrical ConnectionNOTE: If the power supply cord was connected earlier, proceed to“Secure Dishwasher in Cabinet Opening” section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor or lowerpart of dishwasher tub. Pull cable through UL Listed/CSA

Approved strain relief in terminal box. Strain relief is not suppliedwith the dishwasher. Owner must purchase a ⁷ ⁄ ₈" screw-in typestrain relief.

Select UL Listed/CSA Approved twist-on wire connectors (notincluded) rated to connect your household wiring to 16-gaugedishwasher wiring.




INSTALLATION

Form bare ground wire into a U-shaped hook. Wrap ground wirehook clockwise around ground connector screw and under thewasher. Securely tighten ground connector.

NOTE: Twist on UL Listed/CSA Approved wire connector. Gentlytug on wires to be sure both are secured.

Connect wires black to black and white to white, using ULListed/CSA Approved twist-on wire connectors (not included).

If needed, see website for animated representation of this step. Visit www.kitchenaid.com/electrical under FAQ tab.

Tighten strain relief screws to secure cable.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuringwires are not pinched. Use ¹ ⁄ ₄" hex head socket, nut driver or Torx® T20® screwdriver and previously removed screw to secure cover.

WARNING



Connect ground wire to green ground connector interminal box.


Failure to follow these instructions can result in death,fire, or electrical shock.



INSTALLATION


Secure Dishwasher in Cabinet Opening

Check that dishwasher is still level front-to-back and side-to-sidein cabinet opening.

Open dishwasher door, remove lower dish rack, and place towelover pump assembly and lower spray arm of dishwasher. This willkeep screws from falling into pump area when you are securingdishwasher to countertop.

NOTES:

■ Do not drop screws into bottom of dishwasher.

■ If side mounting, you must drill pilot holes in cabinet to avoidsplitting the wood before installing screws. Locate bracketson top of dishwasher and secure dishwasher to countertopwith two #10 x ¹ ⁄ ₂" Phillips-head screws (included). Thedishwasher must be secured to keep it from shifting whendoor is o ened.

Check that top of door does not contact screws, brackets orcountertop. If it does, adjust leveling legs.

Open door and check that space between dishwasher cabinetopening and tub is equal on both sides. If spacing is not equal,loosen bracket screws secured and shift tub. Tighten bracketscrews.

If securing with a side attachment, check that sides of door do notrub against the screw heads. If they do, dishwasher must bere-centered. When dishwasher is properly centered, replaceplastic buttons.




INSTALLATION

Remove towel from dishwasher. Reinstall the lower dish rack.

If needed, see website for animated representation of this step. Visit www.kitchenaid.com/anchoring under FAQ tab.

Bottom Sound Pad Installation(on some models)

1. Remove the bottom sound pad from inside the dishwasherand take it out of the plastic bag.

2. Place pad on the floor in front of the dishwasher, making surelettering is facing up and vinyl pad faces down.

3. Fold up and hold the side panels down. Slowly slide the padtoward the back of the dishwasher as far as it will go, makingsure not to push or pull any wires or hoses. (Do not force.)Side panels will open to proper position.

NOTE: If there are pipes or other obstructions coming upthrough the floor, you will need to cut a slit in the pad to fitaround the obstacle.

4. Fold the front end of the pad up into position. Make sure thevinyl pad is tucked up behind the door and the dishwasherfront legs, as shown.

Complete Installation

Option A, Install Access Panel - Plastic Panel

Place the plastic access panel against the dishwasher leg.

Check that the lower edge of the access panel touches the floor. Adjust if necessary.

Using a flat-blade screwdriver, turn the fasteners ¹ ⁄ ₄ turn clockwiseto lock into place. The fasteners slot will be straight up and downwhen properly locked.



INSTALLATION


Option B, Install Access Panel - Metal Panel

Check that grounding clip is attached to the lower panel. Positionthe lower panel behind the access panel. On some models there

is insulation on the access panel that must fall behind theinsulation on the lower panel.

Hold the 2 panels together and place them against dishwasherleg. Using a Phillips or ¹ ⁄ ₄" screwdriver, reinstall the screws throughthe holes in the access panel and the slots in the lower panel.

Check that the lower edge of the lower panel contacts the floor. Adjust if necessary.

Tighten access panel screws.

Plug into a grounded 3 prong outlet. Check that power supplycord does not touch dishwasher motor or lower part ofdishwasher tub.


Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.


Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING




INSTALLATION

Reconnect Power

Check Operation■ Read the Dishwasher User Instructions that came with your

dishwasher.

■ Check that all parts have been installed and no steps wereskipped. Check that you have all tools used.

■ Start dishwasher and allow it to complete the shortest washcycle. After the first 2 minutes, unlatch door, wait 5 seconds,then open door. Check that there is water in the bottom of thedishwasher tub. Check that dishwasher is working properly.

If the dishwasher is not working properly, disconnect power orunplug dishwasher and see “If Dishwasher Does Not Operate”section.

If Dishwasher Does Not OperateFirst try the solutions suggested here to possibly avoid the cost ofa service call.

■ Has the circuit breaker tripped or the house fuse blown?

■ Is the door closed tightly and latched?

■ Has the cycle been set correctly to start the dishwasher?

■ Is the water turned on?

If none of these possible solutions work, please see your Use andCare Guide for service contact information.

Additional TipsExpect longer wash times. Your new dishwasher will average2-3 hours per load, but use nearly 40% less energy than oldermodels. Designed with a low wattage, low energy consumptionmotor, your dishwasher washes longer to ensure exceptionalcleaning. Certain models are equipped with an optical watersensor so the first cycle will run longer to calibrate to opticalsensor. Selecting certain options could increase cycle time past

3.5 hours.Rinse Aid is necessary for good drying results:This dishwasher is designed to be used with rinse aid for gooddrying performance and controlling hard water deposit buildup.Energy efficient dishwashers use less water and energy, so theydepend on the water sheeting action of rinse aid for good dryingperformance.

Start/Resume light may flash:When pressing Start/Resume, you must make sure the door isclosed within 3 seconds. If you do not close the door within3 seconds, the Start/Resume light will flash until you press itagain. (You must also do this when adding a dish during themiddle of a cycle.)

NOTE: If a braided supply hose is used, replace inlet hose after5 years to reduce the risk of hose failure. Record hose installationor replacement dates on the hose for future reference.

N



COONENT ACCESS


S C A

s so ros sr rs ss rol sllo sros or KA lss l ll Dssr

■ Islo Bl

■ Door r

■ Door r As

■ Wr Il Dr os

■ Orll Assl

■

Ass Door Coos

■ o sr Ir

■ o Assl

■ o lro Corol Bor

■ o Dssr Assl

■ r Ars ol

■ Cooslss l ols

■ o r s

■ o or r Ar

■ o lrs

■ o ror ol Drr Ds

■ r Coos

■ r

■ o Assl Dr

■ o Ol Wr Ior

■ o Drr oor

■ Ws oor



COONENT ACCESS


Dr Srin Austent

1 l ssr or so or

2 o ssr ro sllo

3 W or rso ol ssr o ro o los oor s I oor loss or lls o r s o oorso ll o s

o s oor sr so oo sr ro rr l o ssr r 1

5 s 51 rr or so ro srro sor

sr o o o 3 ols 1 2 3 ro l o ssr s r 1 I oor loss sl o sor o lor-r ol

rl sr7 oor sr o rr l

NOTE sors o o ss o ssr sol sr s ols

ater Inlet an Drain Hse

Drain loop must be higher than drain to preventsiphoning.

ater Inlet Cnents

A D S W W I D

WARNING


Disconnect power before servicing.

Failure to do so can result in death orelectrical shock.

Replace all parts and panels before operating.

Figure 1

Figure 2

Il os

Wr Il

Dr os oo

Dr os

Figure 1



n KitchenAid 2013 Stainless Steel Tall Tub Dishwasher

COONENT ACCESS

Oerll Assebl Cnents

Figure 1

Aessin Oerll Assebl

Figure 2 - Location of Overfill Assembly

1 l or so or

2 O r l s ors r 3

Figure 3

oo o o s oos r

Figure 4

O A

WARNING





Cor

Cor

lo

lo

r

lo

os s

r

l s



COONENT ACCESS

KitchenAid 2013 Stainless Steel Tall Tub Dishwasher n

1 l ssr or so or

2 o srs lo ross o o oor 8 o 10srs sor o ss s rs 1 2

Figure 1

Figure 2

A D C

WARNING





ein Dr anel

3 o or oor l s r 3

Figure 3

Dr Cnents

Figure 4

Dssr

Assl

so ols ol lro Corol



COONENT ACCESS


1 l ssr or so or

2 o or l ro oor3 o sr r ro oor

o ro l ssl sr sll -lsrrr o l slos o s o ll s o rls l ls s r 1 2

R L A

WARNING





Figure 1

Figure 4

Figure 2

o l ssl ro oor r 3

5 Dso rss ssl

Door Assl

Figure 5




COONENT ACCESS

l lro orol o l o oo so o orol ro slos oorr s rs 2 3

1 l ssr or so or

2 o or l ro oor3 Dso rsss ro orol or

3 lo s r 1

Figure 1

R E C B

WARNING





Figure 2

Figure 3

NOTE r r o s o o orol ooo slos oor r

los



COONENT ACCESS


1 l ssr or so or

2 o or l ro oor3 o - - srs sr ssr o

oor s r 1

Dso s rs

5 o ssr ssl r s r 2

Figure 1

Figure 2

R D A

WARNING





Br

DssrAssl

IrDoor l




COONENT ACCESS

omonent dentication

Sra arm

Maniold

Seal

Sra arm

eed tube

S A F T



COONENT ACCESS


T C S S

ater nlet

eed Tube to Middle and

er Sra rm

er ilter

Loer ilter net eater

ater Leel loat

Loer Sra rm

ProScrub Maniold

(aailable on ome model)

Tub omonent dentication




COONENT ACCESS

ein The Uer ar Satinlie rails

1 o ss o r sos ll r rorr o l o o

2 o o r so or os o Ar o o r sos ll o r o o rls r 3

Figure 3

ein the Culinar Tl a3r leel ra aailable n se els

1 o ss r sos ll r orr l sos ls o l

2 o o r sos r so o os o r s r

3 Ar o o r sos sl ro ls o o slo r Co o ll r orr r sl ls o o r

Clos r sos

5 l r rs o ssr

Figure 4

ein The Uer ar Satinlie a rails

1 o ss o rol s o rsrlsll r r orr o l o o

2 O o s rss o r ll ro o r o o r rs 1 2

Figure 1

Figure 2

3 r s s o or s o ollro ro o r

ro o r ll o sll orr r oo

R R

A. Track stopB. Track

A

B



COONENT ACCESS


3 o s r 3

T ree the lwer sra ar

1 or sr r loo s r 1

2 o lor sr r r or loso ro sr r s r 2

Figure 1

Figure 2

Lwer Sra Ar Assebl

ater et

Nut

R L S A

Figure 3




COONENT ACCESS

T ree the lters

1 r lr-s o r lr 1r orlos l o s

rs 1 2

2 or lr- o o s s r 3

R F

Figure 1

Figure 2

Filtran Sste

Figure 3

Upper Filter

Assembly

Lower Filter

P U S H

DOWN&T U R N

L O C K U N

L O C K

Figure 4 - Filtration System



COONENT ACCESS


T ee rSrub anilaailable n se els

1 s ol ro sro

2 Dso ol ro s l s r 1

NOTE orl s r r ors os s orssrol ss lo o ssr

Aessin Dierter Disstainless steel tub

1 s sro ro ls rs 1 2

2 Dso ro rr os sr 3

Figure 1

Figure 1

R S D D

o

Figure 2

Figure 3




COONENT ACCESS

Figure 4

Figure 6

Figure 7

Figure 5

Dierter Dis

rr s s o s s r 7

3 ls lo o rr os s r

R D D

o

o os orlos s r 5

5 o os s r



COONENT ACCESS


Figure 8

Figure 9

Installin Dierter Husin

1 Al rro o rr os o lorrro o s

2 o os lo s l rr oslos l s r 1

Figure 1

R D D

7 o s s rs 8




COONENT ACCESS

T C

AslWls

Wsoor

r

OWI C

Jo Bo

Orlllo l

Dr oor

ll l

Figure 1

Drr oor



COONENT ACCESS


Heater Cnents

A. Heater Element Assembly

B. Rubber Washer

C. Heater Element Nut

D. Speed Nut

E. Heater Probe Shield

A

B

C

D

E

rCoo

rCoo

Figure 1

Figure 2




COONENT ACCESS

Figure 2

Figure 1Figure 4

Figure 3

Figure 5

1 l ssr or so or

2 ls os l ll o os s rs 1 2

Nte B rr o r ro s r

3 o r rss ro r o s o s o o o s s rs 3

l r rss o o r s r 5

o

R S A D

WARNING







COONENT ACCESS


Figure 6

Figure 7

Figure 9 - Locked

7 lo r s sr oor sssl o s rs 8 10

5 o r 1 r or los sr

o r s r 7

Figure 8 - Tab Locations

Figure 10 - Unlocked

R S A D

o

8 Drss lo s r o s o ro s r 11

Figure 11



COONENT ACCESS


Figure 4

Figure 1

Figure 2

Figure 3

Ol r orror s r 1

Ol r or s r s r 2

1 o ol r or or-los 1 rs r 3

2 ll o o ro s r

R O W I

WARNING








COONENT ACCESS

T ree the Dierter tr

1 l ssr or so or

2 o 2 or srs s r 1

3 o s r 2

Figure 1

Figure 2

Nte rr s s oo oor s rr oor ro o ro rrs rs o sll rr oor rr oss ro o l rr s o oor s

emoe Tor cre

R D

WARNING





S A

Isolor

r 3

l

os Asslls 2 ls

ro

Ws oor



COONENT ACCESS


2 o ol ls s r 3

1 s r o ol lrs o o os lss rs 1 2

Figure 2

Figure 1

Figure 3

W R

S R O W

WARNING





o




COONENT ACCESS

3 o oor ro sl s r 5 o sl s r

r o ol sl s r 5

Figure 4

Figure 5

Figure 6

5

S R O W



COONENT ACCESS


1 Isll l s r 1

2 Isll oor s r 2

3 sl s r 3

l sll orrl s r

Figure 1

Figure 2

Figure 3

Figure 4

S I N W

WARNING





o




COONENT ACCESS

5 Ws oor os ls s r 5

Isll ls srs or oo s r

5Figure 5

Figure 6

Figure 7

Figure 8

7 Al s ls s rs 7 8

8 Isll oor ssl ll s r or ls

S I N W

7

8



DIANOSTICS TOUBLESHOOTIN


S D T

s so ros os l os rolsoo oro or KA lss ll Dssr

■ rs

■ Ws Cls

■ r Dos Cl

■ r Dos Cl os

■ Dos

■

r Doss rror Cos

■ r rror Cos

■ rolsoo

■ os





F S T O

oltae Meaurement Saet normationhen erormin lie oltae meaurement ou mut do the olloin

n eri the ontrols are in the o position so that the appliane does not start hen energied.

n llo enough spae to perorm the voltage measurements ithout obstrutions.

n eep other people a sae distane aa rom the appliane to prevent potential inur.

n las use the proper testing euipment.

n ter voltage measurements alas disonnet poer beore serviing.

MPTNT lectrotatic ichare (S) Senitie lectronic

S roblem are reent eerhere Mot eole bein to eel an S dichare at aroimatel

t take a little a to detro damae or eaken the main control aembl The nemain control aembl ma aear to ork ell ater reair i nihed but a malunction ma occur

at a later date due to S tre

n e an antitatic rit tra onnect rit tra to reen round connection oint or unainted

metal in the aliance

n Touch our ner reeatedl to a reen round connection oint or unainted metal in the

aliance

n Beore remoin the art rom it ackae touch the antitatic ba to a reen round

connection oint or unainted metal in the aliance

n oid touchin electronic art or terminal contact handle electronic control aembl b

ede onl n hen reackain main control aembl in antitatic ba obere aboe intruction

MPTNT ST NT or Technician onlThi erice data heet i intended or ue b eron hain electrical electronic and mechanical

eerience and knolede at a leel enerall conidered accetable in the aliance reair trade

n attemt to reair a maor aliance ma reult in eronal inur and roert damae The

manuacturer or eller cannot be reonible nor aume an liabilit or inur or damae o an

kind ariin rom the ue o thi data heet

WARNING





DANGER


Only authorized technicians should performdiagnostic voltage measurements.

After performing voltage measurements,disconnect power before servicing.

Failure to follow these instructions can result indeath or electrical shock.





F S T O

DAI

0 I

00 A

I

055

WA

50

D-

DI

WA

230

A

OD 12

1C 105O 000

WA

2000-

2500

DAI

C

20

I

018

WA

17

DAI

C

057

I

03

WA

50

DAI

C

125

I

051

AD

WA 2

1500

A

OD 12

137-10

585-0C

O 500

I AID

DI

WA

200

I AID

DI

AD

WA

300

DAI

C

00

A

00

D 23

A D

3500

AD D

230

ash Cles Nral Cle O s o os ll rls

DAI

0 I

00 A

I

11

AD

WA

300 2

DAI

C

20

I

10

AD

WA

300 2

DAI

C

13

I

11

D

DI

AD

WA

100 2

DAI

C

20

I

022

WA

030

I

07

AD

WA

3 2

DAI

C

13

I

10

AD

WA

1220

2

I

AID

DI

WA

200

I

AID

DI

WA

230

DAI

C

00

A

00 3

D 23

A D

1730

AD D

2530

DAI

0 I

00 A

I

103

Cl rs s o WA

30

DAI

C

1

I

05WA

30

DAI

C

20

I

015

WA

C

05-13

DAI

C

03

I

05

D

DI

WA

230

A

OD

5C 130

O 000

WA

5500

DAI

C

20

I

015

WA

C

05-13

DAI

C

03

I

05

Cl rs s

WA

00

DAI

C

20

o AD

WA

1500

A

OD

0C 10

O 500

I AID

DI

WA

200

I AID

DI

AD

WA

30 2

DAI

C

00

A

00

D 23

A D 200

AD D 230I

05

One Hur ash O s o os ll rls

ts ans Cle O s o os ll rls

1 THEAL HOLD HEATED ASH UNTIL TEEATUE EACHED O AXIU TIE

2 HEATE NOT ON FO ENTIE D TIE

3 IF HEATED D SELECTED

4 SENSED DAIN DAINS UNTIL ATE IS EOED FO TUB O AXIU TIE

NOTES - Cls so l lo sol rso

- Cls ll r s o ssor s oos sl

- All srs lr sr rs r oor s

- o o r o rss I - AD D - I - AD D oor o or los rsr l

- rss A o l rl





F S T O

S e r i e D i a n s C

l e

S e e S e r i e D i a n s t i C

l e N t e s n l l w i n a e

S e r i e D i a n s t i N t e s





F S T O

Serie Dians Cle Ntes

1 o o oss l ror ollo rsss l s

rss 3 s s 1-2-3 1-2-3 1-2-3

o or 1 so rsss r Dos Cl ll sr oor

s los

o r 1 rl rss A A s ssor ss so s rr o ol rlsNOTE Wl Dos l A r s r o o rs roor rrs A srs s rl

Io r Doss lrs ll ss lsr oro ro or rsors lsI lso ors l o ssor lrol

s Cl Oos rr o lorl Cl Dr Oo

s Dl rrs o los l r

Clro Cl or r rs o orror o l rs o ssr lr r lrs OWI ll o r l rs

Or s rrs o s o olor r sr oss l

2 o ll Ds l o r rs oor s o roo s rsrl s sl s

3 Drr ll o oosl Irl 1 I ll orrr rls rr ll ol o l rs

oso or rl rss I s rl o lr sor rror

sor

5 rsor rr sor s r ClD o rsor s s orl rr r32 o 17 r D o ll rrs o 85

OWI Ol ol sorOl Wr Ior s

OWI sor or rs o r r 5so s Irl 1 rs o ClD Irl 15 r

OWI sor or rs o l sol r sIrl 13 rs o Cl D Irl 12 l sol

Dr l OWI ssor ss rs o r or o 152 r Irls 5 rs o Cl D Irl r

7 DC oor s o r r r s rls

8 r o ll Ds r s ror o sl rroros

s o llo or ol rs ll o

10 or r Ar A ols r-sssor ror ro oo l s o sC or A oor ssor r Irl 10 r llo or loo or rror o o sr l

Interal 10 4 in Lwer ash Diansti DetailsNOTE or r Ar A oor ssor sso r 3r o Irl 10

nl aalale on certan odelsinute 1 LSA tates CC

inute 2 LSA tates C

inute 3 LSA tates CC

Cl D l o A oor ss oo

inute 4 LSA tates C

Cl D l o A ssor ss oo

NOTE Iorl A oor ll lso s A ssor o ss rror o l o osIrl 3 A os o o oso r r olso oso A rol 5 los ro 12 Olo

Dians uie

Bor sr ollo

■ I ll sr r s or ll ol

■ s osol s lo or r rr r

■ Is r sl r o

■ Ar r oss osr

■ All sss sol O ol-o-llr or D l-olr ss o 20000 r ol DC or rr

■ ss s s ssrl or or so

■ IOTANT Ao s lr r ros rss oors s ros oors o sro

■ C ll rsss oos or rloos oo or oors o ll s roor loos rs rls sro or rs orss o oors r o o l rs

■ A ol s o orol o o s orrosoor oo o oos s or o or o ross ss oos





F S T O

Serie Dianss ith Errr CesEntr Seueneo o oss l ror ollo rsss l s rss 3 s s 1-2-3 1-2-3 1-2-3 o or 1 so rsss NOTE o ols rl Cl D Col





F S T O

Serie Errr Ces 1FUNCTIONCODE

OBLECODE

CAUSES HAT TO CHECK

1 - COO 1-IO

CK O

COO DCD K00 IO A CKCOD

1 DIWA O DICOC OW

2 CCK A OAD O K00 IO A O O

3 AC COO AD A OD COO

2-COO

OWA

I

DAAD O COD O OCOO BOAD ICOAIB OWACOO IID ICO

1 DIWA O DICOC OW

2 AC COO BOAD

2- IAC 1-CK

K

COO DCD CK K I KADO KAD COCIO

NOTE COO O A CO IA O CAC K I CK IA O K A CK CK KWI B IOD AD A O CODDO IC IO B O A OCO

CCK OI O AC K

1 I O K DO O OD

- DIWA O DICOC OW

- DIAB DOO AD DICOC KAD COCIOO COO O CD DIA OD

- I A O COCIO O COO A AD

- -AB DOO B DO O CO DOO

- I DIWA O COC OW

- WAI A A 7 COD O COO O OW CO

- CO DIWA DOO OIO COO O

A I COO I OK O O CK K WIKAD D I WI OD B I O DAI OO O 2 I AC KAD ADCOO

B I COO I O OK I CK K WIKAD D I WI O O DAIOO WAI O A A 10 COD I I ODAI O AC COO O CDDIA OD WIC O KAD WACOCD O

2 I K AA O II AD KAD ICAACII OC

A I B BACK A CWD O DID OCOO AD O AI O K I CWAD OO CO OCA CW O AAO

B CCK O IDC O OI O DBI O AC O K I ID CA AD ICCO ABO KI AC CA CCKO COD IO O O 10-2 ADO AO 10-3 A OIA CA O CODAIO O IAC

2-O

O

O I

IAC CA O COICAWI AI COO OO IACCOCIO

1 DIWA O DICOC OW

2 CCK COCIO BW CD DIA OD AD 1CCOCO O COO

I COCIO OO -COC

3 CCK O 5DC O 1C-2 O 1C- I O OA ACOO O OW AD AC AI COOBOAD

WO COO IAD I COC COO I IAD COO OD AO COCO A 1A I WO DICOC OWAD AC COO

3-IOOWI

1-O - O COCIO O COO IA I CICI

- O O A A O

- A A O I OCOO

1 CCK OAIO O A O I ICDIAOIC CC

2 DIWA O DICOC OW

3 CCK A COO AD COCIO I A I CICI WI IACO COCIO A

2-OD - ICOI WA A ABO1775 C

- OD COCIO O COO IA I CICI

- OD O A A O

- A A O I OCOO

1 CCK ICOI WA A

2 CCK OAIO O A O I ICDIAOIC CC

3 DIWA O DICOC OW

CCK A COO AD COCIO I A I CICI WI IACOD WI A OWI O I CICI





F S T O


OBLECODE

CAUSES HAT TO CHECK

3-IOOWI

3-AID

CAIBAIO

OWI AI 1 DIWA O DICOC OW

2 O OWI AD CCK AC ODB CA AD AC OD B O DBI ADCAC CA O AC OWI A DD

3 CCK A COCIO I OI I CICI WI IAC BAD COCIO A

NOTE DIAOIC CC A IAI W OWI OOC CAIBAIO O A WA CC

DAI O CCK A O AI DI WA BACK IO DIWA A DAII

1 DICOC DAI O A BI COCIO

2 A O ABO DIWA AD I WI WA IWA OW IO DIWA AC I DAI OOIA A I A OIB AD AAC O DID OCOO I OIB

-WA OO -OO

AI

OO COCIO I WA OO CICIADO O WA OO

1 DIWA O DICOC OW

2 CCK A COCIO I WA OO CICI WI IAC O COCIO A

OO O COO O O IC DIAOIC CCK O A 1 O CCK DIAA

A WA OO DI CICI O COO

A WA OO

5-DOO

WIC

1-DOO

CK

O

DOO WA O ACD WII 3 CODO I A K

IC CO O CA ID

OO COCIO I DOO WIC CICIADO DOO WIC COAC CKO AD O DOO WIC O AKICOAC

- A O O DOO AC ABWIC CA B AAAD B I DOOCO OC KI IK A O AI

- A DOO WIC I IAC

1 CCK IK A AD DOO CO OC I DOOA I AD O CCK O IC BWDI ACK AD DOO BDI IK A DOW OB A

2 DIWA O DICOC OW

3 CCK DOO WIC COAC AD A COCIO I DOO WIC CICI WI WI OI ADCOI DOO AC

- I I IAC WI DOO COD CCK I OOCOCIO

A IAC O DOO WIC COAC WICCKI CAICA OAIO O AC ABCCK O BOK AIC IC O AC ABAC AC I A

A COO 1 WI DOO O I 13 DC ACO -5 AD-

2 I O OA DIWA O DICOCOW AD AC COO

2-DOO

CK

COD

COO OAD O O A I IC DOO WIC I CK CODCOO OOK O DOO WIC OO BW CC

- CO DID O DOO BWCC O DOO WIC COAC CKCOD

1 O AD CO DOO AD A K IWOK OW IC CO O O DOO BWCC

2 DIWA O DICOC OW

3 A IAC O DOO WIC COAC WICCKI CAICA OAIO O AC AB

-I

WA

1-OWO

WA

CAICA

OB

O WA O DIWA I WA I D O AD I ADA

BOW O O OADD O ID IDDOW AD CAD WA WA

IC CO O OADI O AD CAID

DAI OO DACD O B ADOIO DAI COCIO

CCK O WA IOI O O I

1 AOW DIWA O CO OA I

2 DAI O 5-10 COD B I CACDAI

3 O DOO AD COI WA DO O IO O OI I I DO COI DAI OO I AACD O ID ODIWA AD DAI O I COCD O A DAI AA 508 C 20 IC O OO

WA AKI O DIWA CCK O AK D DIWA





F S T O

FUNCTIONCODE

OBLECODE

CAUSES HAT TO CHECK

-I

WA

1-OWO

WA

CAICA

OB

I A O WA I D WIDBI

O WA O DIWA DICOC WAI O I A AD ICCA I C O

I A AD COC WA

OI WIC CK I OIOIIO ADO DIWA O

CCK O O COD O I - AO OCCD - O COD BOW

I A CICA OB CCK O O COD O I -2 AO OCCD - 2 O COD BOW

2-I

A

CICA

OB

OO COCIO I I A CICIADO O I A OOID

DIWA O DICOC OW AD CCKIAC O I A OOID AD A COCIO I I CICI WI I AC O COCIO A

O O COO O I A O IC DIAOIC CCK O A 1 O CCK DIAA

A I A DI CICI O COO

DIWA O DICOC OW AD ACCOO

3-DAII

OO A D 1 AOW I O I AD WA O 1 I O DOOAD CCK O CI DI

2 COI I O DIWA D O ADD

3 CCK O CI I AID AKA

BOW O O OADD O ID IDDOW AD CAD WA WA

IC CO O OADI O AD CAAA

WA AKI O DIWA CCK O AK D DIWA

DI DIK I I II O OW A A BO O AB ADB AD O CO AD I W DDI DIK I IAD

-OA

WIC

O

OI WIC CK I OI OOIIO ADO DIWA O

O A I CK D OA I A OA O AD O A CICK O WICCOAC CCK O DIWA AWIC IAC I CICI DIAA

DAI O CCK A O AI WA BACK IO DIWA A DAII AD AWA

1 DICOC DAI O A BI COCIO

2 A O ABO DIWA AD I WI WA IWA OW IO DIWA AC I DAI OOIA A I A OIB AD AAC O DID OCOO I OIB

I A IAC O COO OD I I II WI DOO I O I A I CAICACK O BOW I O I WI DOO O CCKOAIO I IC DIAOIC CC ADACIC CC I D DI O I AOD B O I O I DIWA I III I II DIWA O DICOCOW AD AC COO

I A CAICA CK O COI DIWA I WI DOO I O I DIWA O DICOC OW O WAO DIWA AC I A AD WA BACK O

OO A D 1 AOW I O I AD WA O 1 I O DOOAD CCK O CI DI

2 IC CO I I IO DIWAD AD D

3 DICOC OW AC DI I CII AID AKA

O O I A AD O IACOAD

O IC DIAOIC CCK O A 1 O CCK DIAA

Serie Errr Ces 3





F S T O

FUNCTIONCODE

OBLECODE

CAUSES HAT TO CHECK

-I

WA

-COO

WA

ICOI WA D 18 C5 1 B DIWA I COCD O O WA

2 COI A A IK CODD C120IC CO O WA A IK BO IDIWA

3 DIWA O DICOC OW AD CCK ACOCIO AD A IAC I AI CICI AC OWI I IAC I

7-AI 1-O

A

COO OAD O DIAB AB COI I CC I I DCA WA AI OB

I DIAOIC CA COO AD AOW A O O AAI B AO COC WAAI OB O COO WI DIAB AAAI A CICI OB BOW

A CICI OB

- O I A

- O COCIO O COO IA CICI

1 DIWA O DICOC OW

2 A IAC O A AD A COO ADCOCIO I WA AI CICI A D CICII AC O COCIO A

A A DI CICI O

COO

DIWA O DICOC OW AD AC

COO2-A

CK O

A A DI CICI O COO

1 DIWA O DICOC OW AD ACCOO

2 IC A AD COCIO O OAI OI I IDC O OAI O O IAC

8-DAII 1-OW

DAI

OBCD DAI O O A 1 DIWA O DICOC OW

2 CCK O BOCKA O CCK A OCO BI OIA I D ABADIO O O KOCKD O DAI OO CCKA CK ADO D O

DAI I ACD ODAAD

DIWA O DICOC OW AD ACDAI

-DAI

OO

CICAOB

OO COCIO I DAI OO CICIADO O DAI OO WIDI

DIWA O DICOC OW AD CCKIAC O DAI OO WIDI AD A COCIOI DAI CICI I AC O COCIO A

O O COO O DAI OO O IC DIAOIC CCK O A 1 O CCK DIAA

A DAI OO DI CICI O COO

A DAI OO

-DI 1-DI

CA

ID

OIIO

COODD O OO COCIO IDI O OO CICI

1 CCK OAIO I IC DIAOIC CC I OCA CICKI A I OA O IC A WI IOO I OAI DI DI IA I OAI IK O CICI

2 DIWA O DICOC OW AD CCKCOCIO A I DI O AD OOCICI WI I AC COCIO A

3 IC DI O O IDC O WA OCOAIA I AC

CAICA BIDI O DI A

DIC

CCK OAIO O DI OO DI DIAOIC

IC DI A WI IO I OO AA O BO IBA B IID OAIO ACDI AD A

O O COO O DI OO O IC DIAOIC CCK O A 1 O CCK DIAA

A DI OO DI CICI O COO

2-DI

CK O

A DI DI CICI O COO

1 DIWA O DICOC OW AD ACCOO

2 IC DI OO AD COCIO OOAI OI I IDC O OAI OI I AC

Serie Errr Ces 4





F S T O


OBLECODE

CAUSES HAT TO CHECK

-DI 3-DI

DIC

II

COO DCD DI DIK I III

O OW A A BO O AB A DB AD O CO AD I OD DI DIK

I IAD

-OW

A A

O

CAICA BIDI O BOCKI O AA

1 CCK O AD O A BOCKA O OW A AI O AD

2 IC DIAOIC CC AD CCK O AOAIOA DCIO O 10 I AI II

3 DICOC OW O I AD CCK WIICOCIO O DAA A COOD OW A AOO AD O

CCK IAC DIAOIC A CCK OOAD O A 1 AC COO I O

5 CCK O O O OD A OO WIDIIAC AC DI OD

COODD O OO COCIO I AA OOO CICI

O O COO O A AOO

A A A DI CICI O COO

10-O 1-DI

CICA

OB

OO COCIO I DI CICIADO O DI OOID

DIWA O DICOC OW AD CCKIAC O DI OOID O WA OO AD A

COCIO I DI CICI I AC OCOCIO A

O O COO O DI O IC DIAOIC CCK O A 1 O CCK DIAA

A DI DI CICI O COO

DIWA O DICOC OW AD ACCOO

2-

WA

OO

CICA

OB

O A

OD

OO COCIO I CICI ADOO WA OO

DIWA O DICOC OW AD CCKIAC O WA OO AD A COCIO I CICI I AC O COCIO A

O O COO O O IC DIAOIC CCK O A 1 O CCK DIAA

A DI CICI O COO DIWA O DICOC OW AD ACCOO

3-DI

A

O

O OD

WI A

OO COCIO I A CICI ADO

O A OO

DIWA O DICOC OW AD CCK

IAC O A OO AD A COCIO I ACICI I AC O COCIO O A

A A DI CICI O COO DIWA O DICOC OW AD ACCOO





F S T O

CUSTOEDESCITION

OTENTIAL CAUSES CHECK ELATEDEOCODES

CA D A COO OAD WI DIAOIC

AD CIO COD BI DIAD O CO AD O CIO COD OIO O O COD AB IC DIAOIC CC O AD IOO O COD

WO or OW

DAD KADCOO

- O OAIO

- O KAD O

- O D O DIA

O OW O I O BAD COCIO CCK CICI BAK AD JCIO BOCOCIO

OO COCIO I DIWAOW CICI O BW KAD

AD COO

1 DIWA O DICOC OW

2 CCK COII OW COCIO O COO AD

COCIO BW KAD AD COO

OD A A CD DIA AD COO A B CAD O OA I O COAIB WI CDDIA OD

I COC COO I IAD COO ODA O -I IAC COCO A 1A II I COID O A CD OD AC COO

A IAC O COO 1 DIWA O DICOC OW DIABDOO AD IC COO OW COCO ADADJAC C BOAD O DAA AC A DD

2 O IC O COD AB O CK K 2-1 DIAOIC CCK I 1

-I DAI OO O COO I OK AC I

-I DAI OO DO O O AC COO

3 IC I CAB O OO O DAAD WII ACA DD

IC I AB O DAA O COAIAIOAC I A DD

2-1

WO AD D OA K IBIKI OW

B DI I DOO I OD OO A 5 COD O OW IID DI A CC A K O OAIO

IC CO O CA AA

A K O ODI O O O K WO OD

COO DCD DOO WICOB

O IC O COD AB5-1

WO ADD ABO K IAI AID ADCOIO

CK K O CICI I KADO I COO I I A AD K

O IC O COD AB

2-1

WO AD A DO

OWA ADWA ICOAIBIIOB WI COO

O IC O COD AB1-2

WO A AD A K D A3 I W A K I D

COO OOKI O DOO O OBW CC

- CO A O OD DOO ICA CC

- DOO WIC COAC CK COD

O IC O COD AB

5-2

WO ACC K AD COOOCK D O

COO OCKO A ACCIDAD O B CO

IC CO O C AA ODCOO OCK K 5 C O OO 2-1

Trubleshn uie 1

NOTES

■ or rss s rr o Dssr r Crs so

■ or oro oss rr o r Doss Cl so

■ or oro o orl Cl 1-or Cl os s Cl Ws Cl Oro so





F S T O

CUSTOEDESCITION


O O O K WO

OD B O KWOK

-O

A D DIA K BAIO

CK K O CICI I KAD

O I COO I I A AD K

O IC O COD AB

CAACII OC KAD ADICOI OO O COO

1 DIWA O DICOC OW

2 IC KAD BOAD O AAIO O COOAC KAD AD COO I AAIO I

OO COCIO BW KADAD COO AD O B OCOAIAD COCO I

1 DIWA O DICOC OW

2 IC COCIO I IAC CICI -COC OO COCIO AC A I IDAAD O COAIAD

2-2

CI CODAIO O IAC A D O ADO AOB

CCK O IO O 10-2 O O 10-3 AO O IC O COD AB

10-2

10-3

DCI IAC 1 DIWA O DICOC OW

2 AC IAC COO AB

DIWA BCOA O ODWI B

OD DOO DI CC ADCOD DOO WIO I A O CC

IC CO DIWA COO I DID OB I DIWA I I CC I OD WIDOO ACD COO WI O BI W DOO IOD ADO A K I D O CC

OA B OAIO I CIO CO

IC CO OW O B OO AD OD I K O 3 COD O OD

DOO O OD BW CC IC CO COO WI B I W CCAD AD DIWA DOO WA O OD IC A COD CC

5-2

O CC ADOCK I CAI A OCC

A A O OA OAIO DIWA A 2 O 3 I DI CC O A OD ADADAC OC A I

IC CO AI A OD AD OW CC A W OCC AI OW ODA O ICI DIWA O CC B OA

OWI OI O ICKI I OI CCOO O

1 IC DIAOIC CC O CCK I OWI OWII OI WI CA WA

2 CCK AC CA I DD

3 DIWA O DICOC OW

AC OWI DIAOIC A IAI WOWI O OC CAIBAIO O WA CC

A WA AI OB COD CAO CC B WI ICA CA AWA AI A

O IC O COD AB7-1

A AK A O I O A WAWI OW OA

CCK O A A 100AC A OW OC

ICOI WA OO COD O IC O COD AB -

D AI I I ADWA IOD

O IC O COD AB-3

OWI O C O OB O IC O COD AB 3-1 3-3

DO DIA O O I B OOAD I AD O

I I I A DO OD CCK OAIO O CAC K I O CAC D OO I CAC K COO I IK IA DO OD IC DIAOIC CC O CADO OD

O 8 WA OO O IACOAD O COO DIABD OAD

O IC IAC CCK O A 1 O CCK DIAA

CA A A CCB O O AO I - DO OCO CC CAD O CO IAO BIK

COO CACD CC D O ODCD WI WA OO DAIOO OW WA O D

O IC O COD AB -

-1 -3

8-

I I A DO OD IC DIAOIC CC O CA DO OD

Trubleshn uie 2





F S T O

CUSTOEDESCITION


WI O DAI O

C WA IDIWA

O CCK OIO I O OCOD O CICAOB OB ICAICA DO OAC COO

DAI OO CCK A O AI 1 DICOC DAI O A BI COCIO

2 A O ABO DIWA AD I WI WAI WA OW IO DIWA AC I DAIOO IA A I A OIB

CO IDAD WA A DAI

IC CO WI OA A ABO 2C 1 IC O WA AII I I C O ACC

DAII OB O IC O COD AB 8-1 8-

OW A ABOCKI I COA COODOAIO OW AA OD

DOO OD WI OW A AOI

IC CO COOD OW A A OWI C O W DOO I OD

COODD O OO COCIO IA A OOO CICICAI A O O OW OA O OIIO O OIIO A O 5 COCKWI O 12OCOCK

DICOC OW AD CCK COCIO A COODOW A A OO AD O A COO

IC COCO O WA AD COAIAIO ADAC A DD

IC DIAOIC CC AD CCK O AOOO OAIO O 10 O IC

O COD AB

-

D ODII O D I DI OCCK O IOI O O COD OCICA OBOB I CAICADO O AC COO

I I OW ACK BOCKD ID OBOCKD A O WA O DI

IC CO O O DI OADI

CAICA BIDI O DI ID 1 DIWA O DICOC OW

2 CCKAC DI

ID AC BIDI D O CD I CAI

IC CO O O DI II

DI CICA OB O IC O COD AB 10-1


O IC O COD AB -

-1 -3

8-

OO WA CC CIO O CO OAOIA O DI OAD

IC CO O CC CIO COD I OIO O WA OAC BOO

D O DAAD C IC OOWI C

- I C COA C

- I C I C

- I C

A A O OAI O D 1 CCK A OAIO I A BOCKD B DI IIC CO AO CCK O COC A A AI WI DOCKI AIO OCAD OD B A BACK B WA

2 CCK O I D CA O AD COII IAD O

3 COOD OW A A OO AID CCKA A OI I BO DICIO DIDIAOIC CC

-

OO WA D O DAII DIIO A OB

WI O DAI O C WA I IO D O DII O D I

DI O DAI O A I I OCC ADO CK I CAI A O CC


O IC O COD AB -

-1 -3

8-

OI O OB O IC O COD AB O I O OCOD CODD COI OWI A A OWI CCK IIC DIAOIC CC AD CCK O O 3-3

3-2

3-3

DI OB O IC O COD AB -1

-2

DI DIC II O O CO AD IC O D AIC DICO O I O IA W DIC I II

Trubleshn uie 3





F S T O

Trubleshn uie 4CUSTOE

DESCITIONOTENTIAL CAUSES CHECK ELATED

EOCODES

OO WA AI OB O IC O COD AB 7-1

O OB

O O OD

O IC O COD AB-8

I O O O AADO DI

CO O I I AID ADOAD D

CCK I AID A O DIICCO OW O I AD OIO ADD I AID

I AID DI OB O IC O COD AB 10-1

AD WA AI I O DI CCK WA AD I AD IC CO O AI D O OI C O AAIC IO BOO O DIWA AO COD 1 WA CC

O OD WI WA O CCK ADD A D AD O CC I O ADD A IC CO

O OD WI WA O A CICAOB O IC O COD AB

D CAO O O DI CCK WA AD I BOW 10 AI ICCO O D AD COD 1 WA CC

-3

CI O A O OO CD A OO I O A

CCK WA AD I BOW 10 AI ICCO O D AD COD 1 WA CC

DI OB O IC O COD AB -1 -2

DAI OO CCK A O AI 1 DICOC DAI O A BI COCIO

2 A O ABO DIWA AD I WI WAI WA OW IO DIWA AC IDAI OO IA A I A OIB AD AAC ODID O COO I OIB

OO D CO O I I AID ODI

CCK I AID A O DI ICCO OW O I AD OIO ADD I AID

CO O I AD D

OIO

COD O AD D O A D O

COI AID DI OB O IC O COD AB 10-1

CK COD D O IO ACK O O A OD

O IC O COD AB1-1

A OB

O OD WI A

O IC O COD AB10-3


O IC O COD AB -

-1 -3

8-

AI OB O IC O COD AB 7-1

AIID D BIK OICO AIIAIOA A D O CC

COO COD OCOI AIIAIOACID

DOO OD DI IA I O D IC CO

ICOI WA OO COD O IC O COD AB -

AI OB O IC O COD AB 7-1IO OWI O OB O IC O COD AB 3-1 3-2

II DOO WIC ACCOCIO

O IC O COD AB5-1 5-2

I OA OO OW O A AO

CCK OW OC COI A A 100 AC

AI I DIWAD O WAI WI I D CABI OI O DOO WIC COACDI IA I

O IC O COD AB

-3





F S T O

Trubleshn uie 5CUSTOE

DESCITIONOTENTIAL CAUSES CHECK ELATED

EOCODES

D DIWA AD

O A A ADODIWA AWA O

CO O-DIWA A

DI O OAD AIC DI DICO A

IC CO

A I OB O IC O COD AB 3-1

WA AI OB A CKO

O IC O COD AB7-2

WA A DIACD OOI CI AD O D OC

IC A ADJ BACK IO OIIO I DD

OI OAIO A A AD O BOCKD ADAI O DOO

- IC CO I BOCKD

- CCK A A OAIO AD IC O DO I D CA O AD COI IIAD O

- COOD OW A A OO AID CCK AA OI I BO DICIO DI DIAOICCC

-

DI OB O IC O COD AB -1

-2-3

OO OB OC CC O AAD O AD

O IC O COD AB-2

O O OW WA O IC O COD AB -1 -2

-3 -

DAI OO O OW DAI OB - O IC O COD ABO 8-1

8-1

CK O O IC O COD AB 10-2

A AK OI A CCCOD O OD WI A

DIWA I DID O K A I A CCO OI BID I DIWA A WI O I DOO I OD O A 5 C ICCO

CI A OI D O A AO OD WI A 1 CCK A OAIO DI IC DIAOIC CC

2 DIWA O DICOC OW

3 AC A I DO O I

AK O DI OCABI O OO

WA OO OB O AOD

O IC O COD AB10-2

A OB

O OD WI A

O IC O COD AB10-3

OO A D O IC O COD AB -3

-

AKI DIWA CCK DOO B AK AD A WA COCIOD DIWA O IC O AB

-1

-3

I AI OWAD ADWA O O I DICC

CCK O IO O OA O - O - IIK O OCC I I I IIICA ADAI OWAD O IC O AB

-

AI W DOO IOD AD IDIA COD WIDIWA I O CA OC DOO DC

IC CO O A DOO O A W IBO -COI I OD WI DIWA I OC



TESTIN


S T

s so ros r r orol orsos s rors sr rs KA lss l ll Dssr

■ Dssr

■ Wr Dr

■ Corol Bor Ioro

■ rl or o Oro

■ or C

■

Door Cr

■ ll Cr

■ Dssr Cr

■ Wr Dr

■ Wr s OWI

■ Drr oor

■ Drr oso

■ Ws oor rl

■ Dr oor rl

■ W oor

■

■ sr Ir I

■ os




TESTIN

F S T O

oltae Meaurement Saet normationhen erormin lie oltae meaurement ou mut do the olloin

n eri the ontrols are in the o position so that the appliane does not start hen energied.

n llo enough spae to perorm the voltage measurements ithout obstrutions.

n eep other people a sae distane aa rom the appliane to prevent potential inur.

n las use the proper testing euipment.

n ter voltage measurements alas disonnet poer beore serviing.

MPTNT lectrotatic ichare (S) Senitie lectronic

S roblem are reent eerhere Mot eole bein to eel an S dichare at aroimatel

t take a little a to detro damae or eaken the main control aembl The nemain control aembl ma aear to ork ell ater reair i nihed but a malunction ma occur

at a later date due to S tre

n e an antitatic rit tra onnect rit tra to reen round connection oint or unainted

metal in the aliance

n Touch our ner reeatedl to a reen round connection oint or unainted metal in the

aliance

n Beore remoin the art rom it ackae touch the antitatic ba to a reen round

connection oint or unainted metal in the aliance

n oid touchin electronic art or terminal contact handle electronic control aembl b

ede onl n hen reackain main control aembl in antitatic ba obere aboe intruction

MPTNT ST NT or Technician onlThi erice data heet i intended or ue b eron hain electrical electronic and mechanical

eerience and knolede at a leel enerall conidered accetable in the aliance reair trade

n attemt to reair a maor aliance ma reult in eronal inur and roert damae The

manuacturer or eller cannot be reonible nor aume an liabilit or inur or damae o an

kind ariin rom the ue o thi data heet

WARNING





DANGER







TESTIN


F S T O

COO AB

O AAD OA

OA

COO BO

COO BACO O ICA AD OA

A

COO A AOCK COO I AC

BO O BOOO COO OIID IO KO OO COO A OO COO

ETE CHECK OF LOADS SULIES

3 2 1 1 2 3 5 1 3 1 3 1 3 1 3 5 1 3 5 1 1

5 7 8 10 11 12

1 A DC D5 3313

ELECTONIC CONTOL BOAD




TESTIN

F S T O

DANGER





eneral Ther Oeran

eer to rn ara on pae

rl 1 AC ol rs Corol Bor s 1 2 rsl AC s or o DC or l o ol ls l 15 13 5 33 DC s sls r s o ro oro rorossors or oos orol rs or ssors r oor r AC rls 170 DC ol l s s oorol rl s s r oors

13 DC s l o oro o ssrs sl s ssr o or ll 120 AC los

ssr r r o o rl ororoll rs 13 DC s r or sl os ro oor s loso ll o r rls s r oor rls lo rl A rl ol os r orol loss r r or s rlol 13 r loss rl sro AC o lo lo rl ros 1 o rr o oos r oroll rl-ss rs

r r r ss o Corol Bor 1 s oor s r s I 1 s s o r ssr s rsos I oor s s o

o rl s s r oors ll o orA r s s o ll los oroll rs llo or

NOTE r o s r Dos Cs o -

wer Che

s s s or o oo or o ro orol or s s sss ror ols srs ol or r o l

Test reure1 l ssr or so or

2 o ss l

3 o rl o or

W olr s o AC sr l ro s r sr sr r ro s l rsr 1

5 l ssr or ro or

I 120 AC s rs l ssr or soor ro o s

I 120 AC s o rs sor orr orrol ol or rr

o or oor l

7 o or ro orol or lo oor

8 W olr s o AC o l ro o 1 r ro o 2 1

l ssr or ro or

I 120 AC s rs o o s 10

I 120 AC s o rs or o oo rl lo orol r s

10 r DC ls

33 5 DC s s o or ICs ro-rossorso r or lso ro or o oor ssors

I 33 DC r ss ssr olo rsos o r 33 5

olr s o DC o l l o 12-2D r l o 11-2 33

I 5 DC r ss oor or rrs ol o o o r 5 5 olr s o DC o l l o 12-2D r l o 10-5 5

13 DC s s o os o 120 AC rls rs o orol

I 13 DC s ss r oors llor los ol o r o o r 13 5 olr s o DC o l l o12-2 D r l o - 13

Trubleshn issin DC Sulies r o

r r o -3 rolsoo DC sls I 33 5 or 13 DC s ss o orol l ssr or so or so ll ooslos ro orol rlo ss or lo sl l ssr orro or DC sl s rr

I o rl orol

I s r o ssr ro ooor l oo lo o sl s

11 l ssr or so or

12 ssl ll rs ls



TESTIN


F S T O

DANGER





Dr Swith Ciruit

ror ollo s ssr os o oor o or los s s ll ro oor s oor s sl ollos r r o oor s r

■ rssCoo

■ Door Assl

■ Corol Bor

Test reure1 C or ror sllo o ssr or

ll C oor l s or osrosor r oor sl s s rorl Cor rr s rs oor r sssr

2 l ssr or so or

3 o or oor l o ss orol or oor l

Stri Ciruit Dr Swith

C oor s os ll oos oor s r sll ooro orol oor l oor r srlsll

I sl sss o o s 5

I o oors r o sr rorl

ro rs oor ls5 Dso oor ro orol or

s or sr ross s 5 oor los sr oll l ss los

I 3 os or lss s sr ro o s 7

I rss s sr oor s los or loos oos rr s

7 s or sr ross s 5 oor o sr ro ro l ss o

I r s o o s 8

I r sos o or oor s s

rl oor s rs8 l ssr or ro or

s olr s o DC oor o r 13 DC s rs ross - 13 12-2 DC D

I 13 DC s o rs rl orol

I 13 DC s rs ro o s 10

10 ssl ll rs ls

11 l ssr or ro or

12 ror Dos Cl o r rr




TESTIN

F S T O

DANGER





Fill Ciruit

s s ll r oos llr ollo s r r o ll r

■ rssCoo

■ Orll

■ ll l

■ Corol Bor

Test reure1 r r sl s r o sl l s

C or r so o o rloo or ror r oo C or rs

r l or ll l l sr C or ror os oro r s ssr

2 Ar ll los oroll IAC o or

or o oor s IAC s or lorl

O s ll l o o s 3

3 l ssr or so or

Stri Ciruit Fill ale

o or oor l o ss orol or

5 l oor ro orol or

C ll l rsss orsr rss - -

I rss s 80-100 os lll rss r oo o o s 7

I os r rl ll l

I o r s oos rss o orol ll l Ioo rl ll l

7 C o orll ss orsr rss -1 -3 o s loso o

I 3 os or lss s sr o o s 8

I o r or rss s sr oos rss o orol o s I rss s oo rls rs

8 s or sr rss

-1 -3 o s oo I r s o o s

I 3 os or lss s sr or oorll s s rl s rs

o o orol or

10 l ssr or ro or

11 C or AC ol ro Corol r DosCl ror rl sr or AC o o orol - o - s olr s o AC

IOTANT The Fill ale ust be nnete t thentrl bar t easure ltae auratel

I o AC ol s sr rl orol or rs

I 120 AC s sr ll l s r o os 12


13 l ssr or so or

1 ssl ll rs ls

15 l ssr or ro or



TESTIN


F S T O

DANGER





Disenser Ciruit

s s ll r o ssr ssr solo or oor sl ollo sr r o ssr r

■ rssCoo

■ Dssr oloW oor

■ Corol Bor

Test reure1 C or osros or l r

ssr l ro o r or rl sssr

2 Ar ll los oroll IAC o or or o oor s IAC s or lo

rl

O s ll l o o s 3

3 l ssr or so or

Stri Ciruit Disenser


5 l oor ro orol or

C ssr solo or oor o ol rsss or sr rss -1 -3

Sleni

I rss s 280-30 os solo l rss r oo o o s 7

I os r rl ssr solo

I o r s oos rss o orol ssr Ioo rl ssr solo

a tr

I rss s 1-28 os oor rss r oo o o s 7

I os r rl ssr oor

I o r s oos rss o orol ssr Ioo rl ssr oor

7 o o orol or

8 l ssr or ro or

C or AC ol ro Corol r Dos Cl ror rl sr or ACo o orol -1 o -3 s olrs o AC

IOTANT The Disenser Sleni r a tr ustbe nnete t the ntrl bar t easure ltaeauratel


I 120 AC s sr ssr oor sr o o s 10

10 ror Dos Cl o r rr11 l ssr or so or

12 ssl ll rs ls

13 l ssr or ro or




TESTIN

F S T O

DANGER





ater Hean Heat Dr

s s ll r o r l -l ros r sl ollos r r o r r

■ rssCoo

■ r Col

■ ros

■ Corol Bor

Test reureCorol ror o sl r s rol ss Doss o lr orol llo r o r o I

rol s o orr orol ll sl r

1 l ssr or so or

2 o or oor l o ss orol or

3 Dso ro orol or

Stri Ciruit Heater Ciruit

s or sr rss s3

I rss s 8-30 os o o s

I o r s o o s 5

5 sll r oos orolor r l -l ros I

oos loo oo or o ross r l -l

l r l or -l ros slrll o

r or rl r rss s ls o

o o orol or

7 l ssr or ro or

8 C or AC ol ro Corol r Dos Cl ror rl sr orAC o o orol -3 - s olr s o AC

I 120 AC s sr r l s o o os

I o AC ol s sr rl orol or ror Dos Cl o r rr

I r rl rror sll ss ror Wrs s ror o ollo

10 l ssr or so or

11 ssl ll rs ls

12 l ssr or ro or



TESTIN


F S T O

DANGER





ater Sensin with OI Sensr

s s ll r o OWI Ol WrIor orors rr rsor OWI sl ollo s r r o rss r

■ rssCoo

■ OWI sor rr rsor

■ Corol Bor

Test reure1 C oro o rr rsor

r Dos Cl

2 l ssr or so or


Dso 12 ro Corol Bor

5 s or sr rss 12s 1 3 ollo l ros roroo o r rrs r ssorss ls

Stri Ciruit ater Sensin

TE F C ES ANE hs

77 25 C 52 os

10 0 C 11 13 os

NOTE All rsor rss srs s l ssr s l or soro or oor 12 ro ro orol

I rsor rss s OK rsor soo o o s

I rsor rss os o r l rl OWI sor

I o r s oos rss o orol OWI I oorl OWI sor

s or 12 -1 o ro 12-3 o ro

I o sor s o o s 7

I r s o o ro sor

rr or rl r rss rs7 o 12 o orol or

8 W olr s o DC o l l o 12-2 r l o 12-3

l ssr or ro or

10 r Dos Cl ror rlsr or DC o o orol 12-2 12-3

I 33 DC s sr orol s o o os 11

I o DC ol s sr rl orol or rs


12 ssl ll rs ls13 l ssr or ro or




TESTIN

F S T O

DANGER





Dierter tr

s s ll r o rr oor rr oor sl ollo s r r o rr oor r

■ rssCoo

■ Drr oor

■ Drr oso s s o ollo

■ Corol Bor

Test reure1 C or oro Dos Cl s or

l s rosor s s rror o s ro r rr rl I rr s ro

ll rol s rr ssor s sror o ollo r rr s srorl sll o s

2 Ar ll los oroll IAC o or

or o oor s IAC s or lorl

O s rr l o o s 3

Stri Ciruit Dierter tr

3 l ssr or so or


5 l oor 7 ro orol or

C rr oors or sr rss 7- 7-

I rss s 1300-100 os rr oor rss r oo o o s 7

I os r rl rr ssl

I o r s oos rss o orol rrssl I oo rl rr ssl

7 o 7 o orol or

8 l ssr or ro or

C or AC ol ro Corol r Dos Cl ror rl sr or ACo o orol 7- o 7- s olrs o AC

IOTANT The Dierter tr ust be nnete tthe ntrl bar t easure ltae auratel


I 120 AC s sr rr s ro o os 10


I rr rror sll ss ror rr ssor sror o ollo

11 l ssr or so or

12 ssl ll rs ls

13 l ssr or ro or



TESTIN


F S T O

DANGER





Dierter Sensrsin Swith

s s ll r o rr ssorosos rr ssl sl ollo s rr o rr ssors r

■ rssCoo

■ Drr oor s s o ros

■ Drr soroso

■ Corol Bor

Test reure1 C oro o rr oor r

Dos Cl o sol l o r l s ros ro ollo s os

Irl 20 rr oor s r sr o r sr r

Irl 11 rr oor s r sr o ro o so ols ol

Irl 10 rr oor s r sr o lor sr r

Stri Ciruit Dierter Swith

2 I rr s r o o r o sos rr oor s oro o s 3I o ror rr oor s ror o r

3 l ssr or so or

o ss l or oor l

5 sll rr oso s oor 11 oor o orol r srl sll

I sl sss o o s

I o oors r o sr rorlro rs rr oso s

C o o rss rr osos 11 o orol

I o s s oo o o s 7

I o s ls rr or rl rss s

7 o s rr s l oor 11 ro oroor o or ross s 3 o oor ro o orol or

8 l ssr or ro or

sr os l s s 1 r Irls 20 11 10 o sol osr rr oso s los orl ro s rs ol oso

I s s o orll rol 3os or lss los ro o s 10

I s os o o or los rorl or rsss rr 3 os los rlrr ssl rs

10 I ll ros ss ss rl orol or


12 ssl ll rs ls

13 l ssr or ro or




TESTIN

F S T O

DANGER





ash tr ariable See

s s ll r o s oor soor sl ollo s r r o s oorr

■ rssCoo

■ Ws oor rl

■ Corol Bor

Test reure1 C s or

r o Is ssr l r-lr ss r lrs r sllrorl Also s sr r r ols l

2 C s oor lrl oos

ror r Dos Cl olloss ss s s s sssl

3 l ssr or so or


Stri Ciruit ash Drain trs ariable See

5 sll oor 5 s sr ll o orol or

I sl s ss o o s

I sl s l ro 5 r s 2

sll s oor oor s sr

ll o oor I sl s ss o o s 7

I sl s l ro oor oor r s 2

7 C rss orol or soor or o

I r s o o o s 8

I r s o o rr or rl rss s

8 C s oor s Dso 5ro orol or W or r rss ls s so lo

tr Harness inins hs

5 s 1 2 11-13 os

5 s 2 3 11-13 os

5 s 3 1 11-13 os

I ls r os r o oross ro o rl soor

I ls r rs ls rl orol or

l ssr or so or

10 ssl ll rs ls

11 l ssr or ro or



TESTIN


F S T O

DANGER





Drain tr ariable See

s s ll r o r oor roor sl ollo s r r o r oorr

■ rssCoo

■ Dr oor rl

■ Corol Bor

Test reure1 r r os or r s o osr

C or lo ro s l o sorsl C or l r sosl or sosll o o o C r loo s l

or or l oss r s 2 C r oor lrl oos


3 l ssr or so or


Stri Ciruit ash Drain trs ariable See

5 sll oor 5 s sr ll o orol or

I sl s ss o o s

I sl s l ro 5 r s 2

sll r oor oor s sr

ll o oor I sl s ss o o s 7

I sl s l ro oor oor r s 2

7 C rss orol or roor or o

I r s o o o s 8

I r s o o rr or rl rss s

8 C r oor s Dso 5ro orol or W or r rss ls s so lo

tr Harness inins hs

5 s 5 81-5 os

5 s 5 81-5 os

5 s 81-5 os

I ls r os r o oross ro o rl soor

I ls r rs ls rl orol or

l ssr or so or

10 ssl ll rs ls

11 l ssr or ro or




TESTIN

F S T O

DANGER





ent a tr

s s ll r o oor sl ollo s r r o oor r

■ rssCoo

■ W oor

■ Corol Bor

NOTESOl ssrs roDr oo I osr s or r oorls or o s ro r l lo o s o oorl r s los rorl s r Dos Cl

Also r oor sl l sl r o or ss r r r o ls ro l sl llo osr s l o oorl r

Stri Ciruit ent a tr

Test reure1 l ssr or so or


3 l oor 10 ro orol or

C oor rsss

or sr rss 10-1 10-3

I rss s 00-1800 os oor rss r oo o o s 5

I os r rl oor

I o r s oos rss o orol oor I oo rl oor

5 o 10 o orol or

l ssr or ro or

7 C or AC ol ro Corol r Dos Cl sr or AC o o orol 10-1 o 10-3 s olr s o AC

NOTE Dr Dos Cl oor sls r


I 120 AC s sr ssr oor sr o o s 8

8 l ssr or so or

ssl ll rs ls

10 l ssr or ro or



TESTIN


Stri Ciruit ent Fan

F S T O

DANGER





ent Fan

s s ll r o sl ollo s r r o r

■ rssCoo

■

■ Corol Bor

NOTESOl ssrs roDr oo I osr s or r oorls or o s ro r l lo o s o oorl r s los rorl s r Dos Cl

Also r oor sl l sl r o or ss r r r o ls ro l sl llo osr s l o oorl r

Test reure1 C lrl oos


2 l ssr or so or

3 o or oor l o ss orol or l oor 10 ro orol or

5 C rss o oor ol W or o l l o 10- rl o 10-5 IOTANT o sr olr

I rss s 31-1 -os oor rss r oo o o s

I os r rl oor

I o r s oos rss o orol oor Ioo rl oor ssl

o 10 o orol or

7 W olr s o DC o l l o

10- r l o 10-5IOTANT

osr olr

8 l ssr or ro or

C or DC ol ro Corol r Dos Cl ror rl sr or5 DC o o orol 10 s 5

I 5 DC s sr s r o o s 10

I o ol s sr rl orol or rs

10 l ssr or so or

11 ssl ll rs ls

12 l ssr or ro or




TESTIN

F S T O

DANGER





User Interae UI

s s ll r o sr r sr r sl ollo s r r o srr r

■ rssCoo

■ sr Ir I

■ s D O so ols

■ Corol Bor

Test reure1 r orol lo-o r s o

r o sor I ll o r or or ror or C ror o - Also

or ss oso o I rs o or rol

2 l ssr or so or

3 o or oor l o ss orol or sr r

Cntrl Bar User Interae Cnnetins

Dso sr r oo ro orol orr ll or oos o orol r oo

5 -ssl oor o o los oor

l ssr or ro or

7 W ls 7 sos or orol o or-oll

8 Clos ssr oor oor orol rsos

I orol s OK ll rso r o roor or 2 s l sr r ssl

I orol s o OK ll o r o r oorW or ls 10 sos I sll o r rsos rl orol or CD sl ol ro I s o o

l ssr or so or

10 ssl ll rs ls

11 l ssr or ro or



RODCT SECIFICATIONS WARRANT INFORATION SORCES

IN THE UNITED STATES:

FOR RODCT SECIFICATIONS AND WARRANT INFORATION CALL

O WIOO ODC 1-800-253-1301 O KICAID ODC 1-800-22-1230

FOR TECNICAL ASSISTANCE WILE AT TE CSTOERS OE CALL

CICA AIAC I 1-800-832-717

HAE OU STOE NUBE EAD TO IDENTIF OU AS ANAUTHOIED INHOE SEICE OFESSIONAL

FOR LITERATRE ORDERS CSTOER EERIENCE CENTER

O 1-800-253-1301

FOR TECNICAL INFORATION AND SERVICE OINTERSwwwserieaers

IN CANADA:

FOR RODCT SECIFICATIONS AND WARRANT INFORATION CALL

1-800-1-581

FOR TECNICAL ASSISTANCE WILE AT TE CSTOERS OE CALL

CICA AIAC I 1-800-88-71

HAE OU STOE NUBE EAD TO IDENTIF OU AS ANAUTHOIED INHOE SEICE OFESSIONAL

job aid w10573282 kitchenaid dishwasher manual

Documents