jsp_plist_10_respiratory
DESCRIPTION
The seal between the face and the edge of the mask is the most common problem area. You will also see users using a mask after having kept it on their head or hanging round the neck. Quantitative Fit Testing provides the employer with a measurable result for a particular mask on a particular employee and is therefore an extremely important part of an effective Health and Safety programme. BPT050-000-000 Qualitative Fit Testing -TRANSCRIPT
Qualitative Fit Testing
Quantitative Fit Testing
Qualitative Fit Testing can be used on
what are defi ned as tight fi tting respirators,
with the exception of full face masks.
Within the JSP Respiratory Protective
Equipment range these products are :-
• Moulded Disposable Dust Masks
• Vertical Fold Flat Dust Masks
• Tradesman 2 and 3
(fi tted with dust fi lters)
• Midimask Half Mask
(fi tted with dust fi lters)
• Maximask Half Mask
(fi tted with dust fi lters)
• Maximask 2000 Half Mask
(fi tted with dust fi lters)
Full face masks cannot be tested because
the test hood is not large enough for the
mask fi tted with a fi lter. For testing this
product it will be necessary to use the
Quantitative method (discussed below).
Qualitative Fit Testing can be used not
only as a test method to ensure your
employees are properly protected; but
also as a very effective way of training
them in the correct way of fi tting a mask.
Dust and half masks commonly fail to do
the job they are intended to do because
of poor fi tting and care by the user.
The seal between the face
and the edge of the mask
is the most common problem
area. You will also see
users using a mask after
having kept it on their
head or hanging round the
neck.
The test employs a hood
to create a small test
chamber around the users
head, and a test solution.
This test solution has a
bitter taste. It is the same
type of solution that is
put on childrens toys
and fingernails to stop
them chewing them. As
the test uses these two
consumable parts and is
designed to be carried out
by the employer; it is a
very cost effective solution
for assessing the ability of the selected
Respiratory Protective Equipment and the
training given to protect the employee.
JSP offer a Quantitative Fit Testing
service that can be carried out at the
employers site. The service can not only
check how well protected the employers
staff are but also offer training in the
correct fi tting and care of the respirator
being tested.
Quantitative Fit Testing can be used on all
tight fi tting respirators including full face
masks. This means it is suitable for testing
all JSP Respiratory Protective Equipment
except; PowerCap, Jetstream and Air Fed.
However generally speaking this method
will not be used when disposable dust
masks are the RPE being used. JSP use the
Portacount from TSI to carry out on-site
Quantitative Fit Testing. This is an easily
portable particle counting device that has
been developed in the United States of
America. It has been well tested in this
market over many years. Unlike in the EU,
masks in the US are only tested for their
fi ltering effi ciency and not on a selection
of users to check the inward leakage of
contaminants as we do in the EU. The
problem with any standards testing is
that it cannot take into account the large
variation in the shapes of peoples faces
and therefore it is important to know that
a mask actually fi ts the wearers face.
With all Respiratory Protective Equipment,
the most common problem is the fi t of
the mask to the wearers face and the
care taken of the mask. Quantitative
Fit Testing is a very effective, and
importantly, measurable way of ensuring
that the user has a mask that will give
him/her adequate levels of protection.
Portacount works by comparing the
particles outside a wearers mask, with
those inside it, that have got past the
face seal. JSP’s Respiratory Technicians
will fi rst check that there is a suitable
number of particles in the area that the
masks are to be tested in.
At the end of the test, a report is produced
for inclusion in the employee’s records.
While this report is being printed JSP’s
Respiratory Technician will give the
wearer instructions in the care of his/her
respirator.
Quantitative Fit Testing provides the
employer with a measurable result for a
particular mask on a particular employee
and is therefore an extremely important
part of an effective Health and Safety
programme.
Please contact 01993 826050 or email
[email protected] to arrange
for a site visit from one of JSP’s
Respiratory Technicians.
RESPIRATORY PROTECTION - FIT TESTING
Call: 01993 826000 www.jsp.co.uk [email protected] [email protected]
CODE DESCRIPTION CARTON QTY
BPT050-000-000 Qualitative Fit Testing -
To determine the required APF it is simply a matter of dividing the measured level of concentration by the Workplace Exposure
Limit (WEL) that the local legislation allows. This calculation will give a required protection factor, selection is then just to ensure
that the APF for the RPE selected is above the Required. If when selecting RPE their is any question, then a quick call to JSP’s
Technical Helpline on +44(0)1993 826051 will help you solve any queries.
Whether or not a mask/fi lter/respirator is suitable can be determined by using the following calculation:
Required protection factor (RPF) = Measured level of contamination
Exposure limit for contaminateFor example:
RPF = 250mg/m³ 50mg/m³ RPF = 5
Therefore a respiratory device with an APF of 10 would be required (see shaded row above)
Respiratory protection is required where the wearer may encounter one of the following six forms of hazard in the workplace:-
DustFormed by the breaking down of solid materials, normally when materials are altered. For example, sanding, cutting, grinding and brushing. In general the smaller the dust particle the greater the hazard that it presents. Fibres from materials should also be treated as dusts.
MistFormed by processes that involve atomisation (such as spraying, cleaning and cutting/grinding using coolants) and consist of tiny liquid droplets rather like steam in a bathroom.
FumeFormed by the vapourisation of a solid material by the application of intense heat. Extremely fi ne particulates are formed as the fume cools and condenses. Many processes form fume; such as smelting, pouring metals and many welding applications.
VapourA gaseous state formed by evaporation
from substances that are normally either solid or liquid at room temperature. Generally released at room temperature (petrol, methalated spirits), many industrial processes, used in degreasing vapourise particularly quickly once heated.
GasAn air like substance at room temperature. Gases can travel far, very quickly.
Oxygen Defi ciency /Enrichment When an atmosphere is likely to contain less than 19% oxygen (or where conditions may exist in the future to cause this to happen); and in certain circumstances where the risk may be oxygen enrichment, which can lead to explosion and severe impairment of operatives.NOTE: Conventional respirators DO NOT protect the wearer from these hazards.
Respiratory Protection Requirements
Assigned Protection Factors
Assigned Protection
Factor
1/2 or 1/4Mask Plus Filter
Compressed air line
Valved Filtering1/2 Mask
Filtering1/2 Mask
Full FaceMask Plus Filter
Powered Filtering: Helmets and Hoods
EN140 EN270 EN405 EN149 EN136 EN12941
4 P1 - FMP1 FFP1 P1 -
10
P2
Gas X
Gas X +P3
-
FMP2
FMGas X
FMGas X +P3
FFP2 P2 TH1
All Face-Pieces
20 P3 FMP3 FFP3 Gas X
Gas X + P3
TH2
All Face-Pieces
40 - Continuous fl ow
hood & faceshield - - P3
TH3
Semi-hood,
Hood Blouse,
Semi-Blouse
www.jsp.co.uk [email protected] [email protected] Call: 01993 826000 25
RESPIRATORY PROTECTION REQUIREMENTS - RESPIRATORY PROTECTION
CBB610-211-100 Switch & Go Unit 8 Hour EN12941 : 1999 TH2PSL - UK PLUG 1
CBB610-311-100 Switch & Go Unit 8 Hour EN12941 : 1999 TH2PSL - EURO PLUG 1
Jetstream™ Switch & Go Unit (Standard Dust Version) The Jetstream Switch & Go is the fi rst low cost fully approved unit to EN12941, which features ALL the equipment
needed in one complete pack. Jetstream™ is a belt mounted rechargeable respirator with a large capacity disposable dust
fi lter. The waist belt and power unit weighs just 765g. Jetstream™ delivers 180 lt/min of air through the fi lter via a highly
fl exible hose to the desired headtop. The Switch and Go unit comes complete with a white nylon head top. Jetstream Switch & Go pack Contains: PSL Filter, Hose, Charger, Carry Case, Battery, White Nylon Headtop, Flow Meter & UK
Plug. Filter Performance: Offers an assigned protection factor (APF) of 20 x Work place Exposure Limit (WEL) for very fi ne
dusts, fi bres, fumes and aqueous mists.
CCA630-211-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2 Filter - UK PLUG 1
CCA630-311-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2 Filter - EURO PLUG 1
CCA620-211-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2PSL Filter - UK PLUG 1
CCA620-311-100 Jetstream Gas/Vapour GV-X Switch & Go c/w A2PSL Filter - EURO PLUG 1
Jetstream™ Switch & Go™ Gas/Vapour GV-X Version (Complete with white nylon headtop)A2 or A2PSL Filter, Hose, Charger, Carry Case, Battery, White Nylon Headtop, Flow Meter & UK Plug.
Filter Performance: Offers an assigned protection factor (APF) of 20 x Work place Exposure Limit (WEL)
for organic vapours and gases and for very fi ne dusts, fi bres, fumes and aqueous mists.
CBU220-001-100 Jetstream 8 hour Waist Mounted Power Unit c/w TH2SPL Filter - UK PLUG 1
CBU220-301-101 Jetstream 8 hour Waist Mounted Power Unit c/w TH2SPL Filter - EURO PLUG 1
CBU231-201-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2 Filter - UK PLUG 1
CBU231-301-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2 Filter - EURO PLUG 1
CBU233-201-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2PSL Filter - UK PLUG 1
CBU233-301-100 Jetstream Gas/Vapour GV-X 8 Hour Waist Mounted Power Unit c/w A2PSL Filter - EURO PLUG 1
Jetstream™ Waist Mounted Units Complete with Filter & Charger Only (No headpiece supplied)The Jetstream Waist Mounted Unit can be purchased separately to allow it to be combined with an alternative Jetstream
headpieces to provide additional protection to the head, eyes and face.
A2 Filter
A2PSL Filter
RESPIRATORY PROTECTION - JETSTREAM™ POWERED AIR RANGE
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
CODE DESCRIPTION CARTON QTY
JETSTREAM™ SWITCH & GO™ UNIT
1
4
WAIST MOUNTED UNITBlower unit with fully automatic
alarm and integrated battery
providing 180 LT/min of fi ltered air
HEADPIECEA variety of headpieces available to
suit a range of applications
SUPPLY HOSEReinforced hose to prevent kinking
FILTERSChoice of fi lters for different uses
1
2
4
3
JETSTREAMSWITCH & GO
JETSTREAMSWITCH & GO
JETSTREAMSWITCH & GO
SW
ITCH AND
GO
SW
ITCH AND
GO
2
3RI
GHTS RESERVED
DESIGN REGISTERED
a
b
c
d
efg
CBU210-001-100 Waist Mounted Power Unit Only (PSL) for Dust Filter only (No fi lter or charger) 1
CBU211-001-100 Waist Mounted Power Unit Only (G-VX) for Gas Filters (No fi lter or charger) 1
CBU610-000-000 Standard Jetstream PSL Spare Filter 1
CBU620-000-000 Gas/Vapour GV-X A2PSL Spare Filter 1
CBU630-000-000 Gas/Vapour GV-X A2 Spare Filter 1
CBU120-000-000 Spare Charger - UK 1
CBU130-000-000 Spare Charger - EURO 1
CBU020-001-100 Long Jetstream Hose 1
CBU300-001-100 Airfed Replacement Hose 1
CBU010-001-100 Bayonet Fitting 1
CBU150-001-100 Replacement Skirt for Jetstream™ Helmet 1
CBU160-001-300 Replacement Visor for Jetstream™ Helmet 1
CBU170-001-100 Replacement Skirt for Jetstream™ Faceshield 1
CBU180-001-300 Replacement 20cm Slim P/C Visor-Jetstream™ Faceshield 1
CBU240-000-500 Translucent Blue Splash Cover for Jetstream™ Filter 1
Jetstream™ Spares Spares to maintain Jetstream as a highly effective respiratory product.
CBH050-000-000 Jetstream Clear PVC Hood 1
Jetstream™ Alternative Headpiece Clear PVC HoodFor pharmaceutical and high visibility work. The semi rigid visor allows a high optical clarity, ideal for clean room
environments. Conforms to BS EN 12941:1999
CBH040-000-000 Jetstream Non-Woven Hood 1
Jetstream™ Alternative Headpiece Non-Woven HoodLightweight hood with clear non impact visor, designed for semi disposable applications. Conforms to
BS EN 12941:1999
CBH010-000-000 Jetstream MK7 1
Jetstream™ Alternative Headpiece MK 7 Helmet with VisorHDPE industrial safety helmet to EN397 for protection against falling hazards with sealed visor.
Conforms to BS EN 12941:1999 TH2 Polycarbonate visor gives protection to EN 166.1.B.3.9
CBH030-000-000 Jetstream White Nylon Hood 1
Jetstream™ Alternative Headpiece White Nylon HoodMore sturdy than the Non Woven hood but still lightweight. White for most industrial environments.
Conforms to BS EN 12941:1999
CBJ031-001-100 Jetstream™ AIRFED COBRA * DIN 9-13 Airfed Cobra Welding 1
CBJ011-001-100 Airfed Welding/Grinding Visor DIN 9-13 1
CBJ020-001-300 Airfed Grinding Visor Only 1
i. Jetstream™ Airfed CobraDesigned to attach to the JSP Jetstream™ powered air unit. The Airfed Cobra™ has a uniquely developed
highly effi cient yet quiet air fl ow system through which 180 Ltrs per minute of fi ltered air is delivered.
Conforming to EN 12941 :1999. Designed to be the most cost effective powered air shade 9-13 auto
darkening fi lter (ADF) welding helmet on the market. Also available with a grinding visor.
Airfed
Welding/Grinding
Airfed
Grinding Visor
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 27
JETSTREAM™ POWERED AIR RANGE - RESPIRATORY PROTECTION
JETSTREAM™ ALTERNATIVE HEADPIECES
CODE DESCRIPTION CARTON QTY
a
b
c
d
e
f
g
CAD602-21A-100 PowerCap® Lite ip - 8 hour re-chargeable - Wipeable Lite UK Plug (Made to order) 1
CAD602-31A-100 PowerCap® Lite ip - 8 hour re-chargeable - Wipeable Euro Plug (Made to order) 1
PowerCap® Lite ip WipeableAll the benefi ts of the Powercap lite plus the benefi ts of being easily wiped clean in a hygienic manner.
Conforms to EN 166, EN812, EN12941 TH1P
CAU020-001-100 Cap Black 1
CAU140-000-000 Powercap® Charger with UK plug 1
CAU130-000-000 Powercap® Charger with Euro plug 1
CAU110-000-000 Powercap® Charger with US plug 1
CAU610-000-010 Powercap® prefi lter Packs 1
CAU601-001-100 Filter TH1P (per pair) Black 1
CAU030-000-000 Standard Visor Kit 1
CAU080-000-000 Impact Protection Visor Kit 1
CAU070-001-100 Face Seal 1
CAU150-000-000 Peel Off Visor for Powercap®(Pack of 10) 10
PowerCap® SparesSpares to keep Powercap providing optimal levels of protection.
CAD601-201-100 PowerCap® Lite - 4 hour re-chargeable UK Plug - Black 1
CAD601-211-100 PowerCap® Lite - 8 hour re-chargeable UK Plug - Black 1
CAD601-301-100 PowerCap® Lite - 4 hour re-chargeable Euro Plug - Black 1
CAD601-311-100 PowerCap® Lite - 8 hour re-chargeable Euro Plug - Black 1
PowerCap® LiteThe Powercap Lite incorporates lithium ion batteries derived straight from the latest mobile telephone battery technology.
This has enabled the battery to be incorporated within the headpiece, so it is completely self-contained without any ancillary
battery pack. It provides the wearer with a greater feeling of freedom and ease of use, and will provide a consistent airfl ow
of 160 litres a minute for 4 or 8 hours continuously, with only 440g head weight. Conforms to EN12941 TH1P
CAD602-201-100 PowerCap® Lite ip - 4 hour re-chargeable UK Plug - Black 1
CAD602-211-100 PowerCap® Lite ip - 8 hour re-chargeable UK Plug - Black 1
CAD602-301-100 PowerCap® Lite ip - 4 hour re-chargeable Euro Plug - Black 1
CAD602-311-100 PowerCap® Lite ip - 8 hour re-chargeable Euro Plug - Black 1
PowerCap® Lite ip - Impact Protection A Powercap Lite incorporating BumpCap protection and and Impact Faceshield. Conforms to EN 166, EN812, EN12941 TH1P
RESPIRATORY PROTECTION - POWERCAP® POWERED AIR RANGE
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
POWERCAP® LITE & IP LITE
CODE DESCRIPTION CARTON QTY
POWERED AIRGives a cooling, comfortable supply of fi ltered air
at 160 litres/minute. Equivalent to FFP2 levels
with an Assigned Protection Factor (APF) of 10
BUMP CAP PROTECTIONBump Cap Protection to EN812. Ideal for working
in confi ned spaces when there is a danger of
bumping or scraping the head
RECHARGEABLE BATTERIESLithium Re-chargeable 4 or 8 hour batteries
IMPACT PROTECTIONPowercap ip gives eye and face impact protection
to EN166 1B Ideal for working where there is a
danger of fl ying particles
1
2
4
3
1
2
3
4 RIGH
TS RESERVED
DESIGN REGISTERED
HEAD HARNESSAdjustable headpiece to get best possible fi t and comfort.
HOOD SEALHood to seal breathing area and to ensure high levels of
wearer comfort and cleanliness.
FACESHIELDHigh performance headpiece incorporates the proven JSP
Invincible faceshield with acetate or polycarbonate visor.
REGULATORPreset regulator incorporating fl ow warning gauge with
integrated high effi ciency coalescent fi lter.
1
2
4
3
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 29
ILES OPTICAL® AIRFED RANGE - RESPIRATORY PROTECTION
G-N-AF-KitBrowguard, harness, Visor, air tube & diffuser, face seal, neck cover,
Waistbelt with carbon fi lter regulator, visor cover and storage bag1
G-N-AFB-A Browguard, harness, Visor, air tube & diffuser, face seal, neck cover. 1
Airfed Faceshield The airfed faceshield meets all requirements of EN 270, features a preset regulator to ensure that the wearer receives a
continuous fl ow of 160-230 Ltr / min to faceshield head piece with a protection factor of up to 200.
CODE DESCRIPTION CARTON QTY
BUA080-000-000 Wall Mounted Single Man Filter Unit 1
BUA100-000-000 Carbon Cartridge for Wall mounted Unit 1
Wall Mounted Single Man Filter UnitRequired where the compressed air supplied is not of breathable quality. The three-stage fi ltering removes large particles,
then oil mists, water and submicron particles, the fi nal fi lter removing any remaining oils.
G-N-AF-W-R-CF-Y Belt Regulator: Waistbelt c/w Carbon cartridge, air fl ow regulator, Q/R connector, Y piece 1
G-CC-CE Carbon Cartridge for Belt Regulator 1
Belt Regulator and Filter Assembly Belt with pocket regulator and coalescent fi lter to remove low levels of moisture and oil.
G-N-AFB Spare Browguard 1
G-N-AF-A170 Acetate Visor - 17cm 4
G-N-AF-BT Air Tube with diffuser 1
G-N-AF-HYGKIT Hygiene Kit - 5 x face seal, 5 x Sweatbands 1
G-N-AF-VC10 Disposable Visor Cover (pack 10) 1
G-N-AF-NC Fabric neck cover 5
G-N-AF-BAG Fabric storage bag 1
Replacement PartsUser replaceable parts to maintain the faceshield’s high performance.
1
2
3
4
AIRFED RANGE
RESPIRATORY PROTECTION - OLYMPUS® FULL FACE
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
Olympus® Silicone Full Face Mask - BlackModern design which features a completely clear visor design increasing
light levels within the mask and decreasing the feeling of claustrophobia
often experienced using full face masks. The Silicone construction
increases user comfort. It has a wide scratch resistant polycarbonate
visor and a lightweight centre canister connector for optimum balance.
The 5 point suspension harness and chin recess ensure a comfortable and
a stable fi t. Conforms to EN136
BPA000-011-000 Silicone Full Face Mask - Black 1
BMV210-000-000 A2 - DIN Thread Filter Canisters 22 x 3
BMV230-000-000 B2 - DIN Thread Filter Canisters 22 x 3
BMV270-000-000 K2 - DIN Thread Filter Canisters 22 x 3
BMV310-000-000 A2P3 - DIN Thread Filter Canisters 22 x 3
BMV340-000-000 ABEK2 - DIN Thread Filter Canisters 22 x 3
BMV360-000-000 ABEK2P3 - DIN Thread Filter Canisters 22 x 3
BMV370-000-000 AB2P3 - DIN Thread Filter Canisters 22 x 3
BMV430-000-000 AB2 - DIN Thread Filter Canisters 22 x 3
BMV390-000-000 P3 - DIN Thread Filter Canisters 22 x 3
Olympus® DIN Thread Canister FiltersA full range of quality multi-fi t DIN thread Filter Canisters giving protection
against either gases, particulates or a combination of the two. Colour coded to
European norms in EN 14387 & EN 143
OLYMPUS® FULL FACE MASKS
CODE DESCRIPTION CARTON QTY
BPE000-011-000 Rubber Full Face Mask - Black 1
Olympus® Rubber Full Face Mask - BlackA well balanced rubber full face mask designed to accept JSP DIN
Canisters and other Canister fi lters using standard EN 148-1 (DIN)
thread connection. It features a wide scratch resistant polycarbonate
visor and a lightweight centre canister connector for optimum balance.
The 5 point suspension harness and chin recess ensure a comfortable,
stable fi t. Conforms to EN136.
Filter TypeType Colour Code DescriptionA Organic Vapours and Gases with boiling point 65°C and above
B Inorganic Vapours and Gases (excluding Carbon Dioxide/Monoxide)
E Sulphur Dioxide and Other Acidic Vapours and Gases
K Ammonia and Ammonia Derivatives Vapours and Gases
ABEK Combination fi lter, all of the above
P Dust/Particle
Filter Classifi cationClass Dust Gas Vapor1 Low Effi ciency Low Capacity
2 Medium Effi ciency Medium Capacity
3 High Effi ciency High Capacity
CODE DESCRIPTION CARTON QTY
31
MAXIMASK 2000™ HALFMASK RANGE - RESPIRATORY PROTECTION
BHS383-005-800 Maximask 2000 - 2x P2 Filters - Blue 24
BHS393-005-800 Maximask 2000 - 2x P3 Filters - Blue 24
BHS213-005-800 Maximask 2000 - 2x A1 Filters - Blue 24
BHS193-005-800 Maximask 2000 - 2x A2 Filters - Blue 24
BHS263-005-800 Maximask 2000 - 2x K1 Filters - Blue 24
BHS333-005-800 Maximask 2000 - 2x ABEK1 Filters - Blue 24
BHS323-005-800 Maximask 2000 - 2x AB1 Filters - Blue 24
BHS543-005-800 Maximask 2000 - 2x AB1 Filters and P2 Pre-Filters - Blue 24
BHS553-005-800 Maximask 2000 - 2x A1 Filters and P2 Pre-Filters - Blue 24
BHS303-005-800 Maximask 2000 - 2x A2P3 Combination Filters - Blue 24
BHS423-005-800 Maximask 2000 - 2x AB1P3 Combination Filters - Blue 24
BHS523-005-800 Maximask 2000 - 2x ABEK1P3 Combination Filters - Blue 24
Maximask 2000™ c/w Filter Cartridges in Clam Shell packagingA premium half mask offering protection and comfort. A unique, extra wide sealing surface offers
unparalleled comfort and fi t. Available in durable thermoplastic rubber. Masks are supplied with low
profi le fi lters with push and quarter turn fi tting. Packed in clam shells.
Maximask 2000™ Replacement Cartridges and Filters (sold in pairs)Replacement fi lter with unique Maximask 2000 fi tting. Filters perform to EN143 and
EN14387. Available in both clam shell and hanging bag.
BHS003-005-000 Maximask 2000 - Blue supplied boxed without cartridges 48
Maximask 2000™ without Filter CartridgesMask supplied without fi lters to allow purchaser to select the fi lter or range of fi lters
required for a particular application.
MAXIMASK 2000™ HALF MASKS
CODE DESCRIPTION CARTON QTY
CODE (CLAM SHELL)
QTY(PAIRS)
CODE (BAGGED)
QTY(PAIRS) DESCRIPTION
COMFORTDurable thermoplastic rubber mask for superior fi t to most face shapes.
HARNESSFully adjustable four point cradle suspension ensuring an effective facial fi t.
VALVELow resistance exhalation valve for easy breathing, with stable mask confi guration
FILTERLow profi le angle fi lter design for minimum visual impairment.
1
2
4
3
1
3
2
4
BMH380-011-000 56 BMH380-011-700 80 P2 Dust Cartridge
BMH390-011-000 40 BMH390-011-700 80 P3 Dust Cartridge
BMT380-000-900 56 BMT380-000-700 80 P2 Pre Filter Pack (2 Covers & 2 Filters)
BMH210-011-000 40 BMH210-011-700 80 A1 Organic Vapour Cartridge
BMH190-011-000 40 BMH190-011-700 80 A2 Organic Vapour Cartridge
BMH260-011-000 40 BMH260-011-700 80 K1 Ammonia Cartridge
BMH320-011-000 40 BMH320-011-700 70 AB1 Organic & In-Organic Cartridge
BMH330-011-000 40 BMH330-011-700 70 ABEK1 Combination Vapour Cartridge
BMJ540-011-000 40 BMJ540-011-700 70 AB1 P2 Organic & In-Organic Vapour & Dust Cartridge
BMJ550-011-000 40 BMJ550-011-700 80 A1 P2 Organic Vapour Dust Cartridge
BMJ300-011-000 40 BMJ300-011-700 70 A2P3 Organic Vapour & Dust Cartridge
BMJ420-011-000 40 BMJ420-011-700 70 AB1P3 Organic & In-Organic Vapour & Dust Cartridge
BMJ520-011-000 40 BMJ520-011-700 70 ABEKP3 Combination Vapour & Dust Cartridge
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050
RESPIRATORY PROTECTION - FILTERSPECTM RANGE
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
FULLY ADJUSTABLEFully adjustable spectacle frame for maximum comfort and security.
LIGHTWEIGHTLightweight re-usable fi lter holder element for an economic PPE solution.
FILTER MASKExhale valve is fi tted to reduce heat &
CO2 buildup for greater comfort.
PERFECT FITComfortable fi t and no steaming.
1
2
3
FILTERSPEC™ -
FilterSpec™ White with 3 Filters, Clear Lens The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens
offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. FMP2 fi ltration giving
94% effi ciency. Includes white holder, 3 fi lters and spectacle with Clear HC & Anti-Mist Lens.
CODE (CLAM SHELL)
CODE (BOXED)
DESCRIPTION CARTON QTY
ASF02B-100-100 10 FMP2 Filters 20
ASG02B-100-100 10 FMP2 Valve Filters 20
ASG04B-100-100 10 FMP2 Odour Valve Filters 20
ASG03B-100-100 10 FMP3 Valve Filters 20
FilterSpec™ - White Replacement Filters Pack of 10Replacement Filters for the FilterSpec & FilterSpec Pro
FILTERSPEC™ REPLACEMENT FILTERS - WHITE
SPECTACLE• Stylish spectacle element design.
• Fully adjustable spectacle frame for maximum
comfort and security.
• 6.5 base, one-piece lens offers optimal coverage.
• Anti-Mist Coating on Lens as standard.
• Anti-Scratch Coating on Lens as standard.
• Wide range of lens coatings available.
• Wide range of colour combinations available.
Spectacle Conforms to: EN166.1.F
FILTER MASK• Disposable fi lter mask element for optimum protection.
• Re-usable fi lter holder element for an economic PPE solution.
• Lightweight for user comfort. (Under 60g)
• Exhale valve fi tted for increased fi lter element longevity.
• Each product comes supplied with 3 fi lter elements.
• Removable, replaceable elastic strapping.
Mask Conforms to: EN1827:1999:+A1:2009
FILTERSPEC™ - WHITE
CODE DESCRIPTION CARTON QTY
THE ONLY APPROVED COMBINATION EYE & RESPIRATORY PROTECTION IN THE WORLD
4
NEW1
2
3
PATE
NT PENDING
DESIGN REGISTERED
ASF129-120-100 ASF124-120-100 FilterSpecTM White with FMP2 Filter (Clear Lens) 20
ASG129-120-100 ASG124-120-100 FilterSpecTM White with FMP2 Valve Filter (Clear Lens) 20
ASG149-120-100 ASG144-120-100 FilterSpecTM White with FMP2 Odour Valve Filter (Clear Lens) 20
ASG139-120-100 ASG134-120-100 FilterSpecTM White with FMP3 Valve Filter (Clear Lens) 20
AGB120-201-100 FilterSpecTM Pro Black with FMP2 Filter (Clear Lens) 20
AGE120-201-100 FilterSpecTM Pro Black with FMP2 Valve Filter (Clear Lens) 20
AGE150-201-100 FilterSpecTM Pro Black with FMP2 Odour Valve Filter (Clear Lens) 20
AGE130-201-100 FilterSpecTM Pro Black with FMP3 Valve Filter (Clear Lens) 20
FilterSpec™ Pro - Black with 3 Filters, Clear Lens - (Boxed) The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens
offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. Includes black
holder, 3 fi lters and goggle with Clear HC & Anti-Mist Lens.
FilterSpec™ - Black with 3 Filters, Clear Lens The unique FilterSpecTM effortlessly combines both eye & respiratory protection. The one-piece lens
offers optimal coverage and has Anti-Mist and Anti-Scratch coating as standard. FMP2 fi ltration giving
94% effi ciency. Includes black holder, 3 fi lters and spectacle with Clear HC & Anti-Mist Lens.
ASF02B-101-100 10 FMP2 Filters 20
ASG02B-101-100 10 FMP2 Valve Filters 20
ASG04B-101-100 10 FMP2 Odour Valve Filters 20
ASG03B-101-100 10 FMP3 Valve Filters 20
FilterSpec™ - Black & FilterSpec Pro - Black Replacement Filters Pack of 10Replacement FiltersTM Black
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 33
FILTERSPECTM RANGE - RESPIRATORY PROTECTION
FILTERSPEC™ - BLACK
CODE (CLAM SHELL)
CODE (BOXED)
DESCRIPTION CARTON QTY
FilterSpec™ - Black with 3 Filters, Smoke Lens Includes black holder, 3 fi lters and spectacle with Smoke HC & Anti-Mist Lens.
CODE DESCRIPTION CARTON QTY
FILTERSPEC™ PRO - BLACK
FILTERSPEC™ REPLACEMENT FILTERS - BLACK
CODE DESCRIPTION CARTON QTY
ASF129-121-100 ASF124-121-100 FilterSpecTM Black with FMP2 Filter (Clear Lens) 20
ASG129-121-100 ASG124-121-100 FilterSpecTM Black with FMP2 Valve Filter (Clear Lens) 20
ASG149-121-100 ASG144-121-100 FilterSpecTM Black with FMP2 Odour Valve Filter (Clear Lens) 20
ASG139-121-100 ASG134-121-100 FilterSpecTM Black with FMP3 Valve Filter (Clear Lens) 20
CODE (CLAM SHELL)
CODE (BOXED)
DESCRIPTION CARTON QTY
ASF129-125-800 ASF124-125-800 FilterSpecTM Black with FMP2 Filter (Smoke Lens) 20
ASG129-125-800 ASG124-125-800 FilterSpecTM Black with FMP2 Valve Filter (Smoke Lens) 20
ASG149-125-800 ASG144-125-800 FilterSpecTM Black with FMP2 Odour Valve Filter (Smoke Lens) 20
ASG139-125-800 ASG134-125-800 FilterSpecTM Black with FMP3 Valve Filter (Smoke Lens) 20
RESPIRATORY PROTECTION - DISPOSABLE MASKS, TYPHOON™ TECHNOLOGY
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
BEY110-201-000 Typhoon Horizontal FoldFlat FFP1 - 315 Overfl ow Valved 10 x 10
BEY120-201-000 Typhoon Horizontal FoldFlat FFP2 - 325 Overfl ow Valved 10 x 10
BEY150-201-000 Typhoon Horizontal FoldFlat Odour FFP2 - 326 Overfl ow Valved 10 x 10
BEY130-201-000 Typhoon Horizontal FoldFlat FFP3 - 335 Overfl ow Valved 10 x 10
TyphoonTM Valve Fold Flat MasksHorizontal Foldable Shape for better fi tting and clear vision, hygienically
individually packed. Extremely low breathing resistance, extremely low CO2
and heat build up, and extremely low moisture build up.
Conforms to EN149:2001+A1:2009
CODE DESCRIPTION CARTON QTY
HORIZONTAL FOLD FLAT MASKS WITH TYPHOON™ VALVE
360O COMFORT FOAM A foam area around the inside of the mask provides a perfect fi t and
maximum resistance as well as preventing misting.
WELDED NOSE PIECEThe welded nose piece prevents any irritation,
misshaping and a tighter fi t
LATEX FREE ADJUSTABLE STRAPThe adjustable strap means it can be fi tted comfortably
to all head sizes and shapes.
UNIQUE VALVEThe silicone valve is unaffected by any moisture,
and therefore can be used with the same
performance under very low temperatures.
1
2
3
4
THE UNIQUE TYPHOON™ VALVE SYSTEMWhen the Diaphragm opens, exhaled air that would
normally be trapped under the upper section of the cage
and obstruct further exhalation, can escape, through the
additional overfl ow vents, and assure unrivalled minimum
breathing resistance. The Diaphragm is made out of
Silicone in order not to be affected by any moisture, and
therefore can be used with the same performance under
very low temperatures.
315 - FFP1 VALVED
NEW12
34
4
RIGH
TS RESERVED
DESIGN REGISTERED
325 - FFP2 VALVED
326 - FFP2
ODOUR VALVED
335 - FFP3 VALVED
FLEXIBLE COVER Flexible cover to protect and retain the shape of the mask
during long periods of wear
FACE SEALImproved Face seal for added comfort
GRILLTo protect the wearer against possible damage to the fi lter.
Hand welded seal allows for extremely effi cient sealing.
MODERN VALVEModern design valve allows for lower
breathing resistance.
1
2
3
4
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 35
FLEXINET™ DISPOSABLE MASKS - RESPIRATORY PROTECTION
BEQ122-101-000 FFP2 - 821 -
Small/Medium10 x 10
BEQ122-201-000 FFP2 - 821 -
Medium/Large10 x 10
Flexinet™ FFP2 - 821Medium effi ciency (94%
minimum) dust mask. There is
no need for a valve for lower
breathing resistance.
CODE DESCRIPTION CARTON QTY
FLEXINET™ DISPOSABLE MASK
BER152-101-000 FFP2 Odour Valved -
823 - Small/Medium 10 x 10
BER152-201-000 FFP2 Odour Valved -
823 - Medium/Large 10 x 10
Flexinet™ FFP2 Odour Valved - 823 Activated carbon layer is
incorporated to remove
nuisance odours.
CODE DESCRIPTION CARTON QTY
BER122-101-000 FFP2 Valved - 822-
Small/Medium10 x 10
BER122-201-000 FFP2 Valved - 822-
Medium/Large10 x 10
Flexinet™ FFP2 Valved - 822Medium effi ciency (94% minimum)
with exhalation to increase
comfort.
BER130-001-000 FFP3 Valved - 832
- One Size Only10 x 5
Flexinet™ FFP3 Valved - 832High effi ciency (99%
minimum) fi ltering
with exhale valve
and fully adjustable
4-point harness.
FLEXINET™ DELUXE DISPOSABLE MASK
The FlexinetTM disposable mask has an ergonomic 3D design to fi t most face shapes, and has extremely low breathing resistance due
to the mask’s design and protective shield. Because it has no metal parts it is ideal for use within the medical & pharmaceutical industry.
Available in two sizes (small/medium & medium/large), perfect for fi t testing. Conforms to EN149:2001+A1:2009
1
2
3
4
4
RIGH
TS RESERVED
DESIGN REGISTERED
RESPIRATORY PROTECTION - DISPOSABLE MASKS
Call: 01993 826050 www.jsp.co.uk [email protected] [email protected]
BEJ110-001-000 FFP1 - 111 10 x 20
BEK110-001-000 FFP1 - 112 Valved 10 x 20
BEK140-001-000 FFP1 - 113 Odour Valved Welding 10 x 20
FFP1 Moulded Disposable MasksThis “shaped to fi t” quality range of
moulded disposable masks are available in
Small, Medium and Large sizes. The valve
products increase user comfort by lowering
C02 and heat build up. Class 1 effi ciency
(80% minimum) for low risk hazards where
a protection factor up to 4 is required.
Conforms to EN149:2001+A1:2009
CODE DESCRIPTION CARTON QTY
MOULDED DISPOSABLE MASKS
BEJ120-001-000 FFP2 - 121 10 x 20
BEK120-001-000 FFP2 - 122 Valved 10 x 20
BEK150-001-000 FFP2 - 123 Odour Valved Welding 10 x 20
FFP2 Moulded Disposable MasksClass 2, medium effi ciency
(94%) with a protection
factor of 10. Conforms to
EN149:2001+A1:2009
BEK130-001-000 FFP3 - Valved - 132 Medium 10 x 5
FFP3V Moulded Disposable MasksClass 3, high effi ciency (99%) with a protection factor of 20.
Conforms to EN149:2001+A1:2009
BEA110-101-000 FFP1 - 211 10 x 20
BEB110-101-000 FFP1 - Valved - 212 10 x 10
BEA120-101-000 FFP2 - 221 10 x 20
BEB120-101-000 FFP2 - Valved - 222 10 x 10
BEB150-101-000 FFP2 - Odour - Valved - 223 10 x 10
BEB130-101-000 FFP3 - Valved - 232 10 x 10
Disposable Vertical Fold Flat MasksHandy sized and easily pocketed these individually packed masks
hygienically fold fl at when not in use. Ergonomically shaped for an
effi cient fi t. Conforms to EN149:2001+A1:2009
CODE DESCRIPTION CARTON QTY
FOLDFLAT DISPOSABLE MASKS
Hand SanitiserThe sanitiser is available
in 500ml pump disepnser
and a personal 50ml bottle,
supplied in counter top
display cartons.
ASE210-000-000 500ml Bottle 10
ASE201-000-000 Box of 42 x 50ml Bottle 1
FFP1
FFP1V
FFP1OV
FFP1 FFP1V
FFP2
FFP20V
FFP2V
FFP3V
FFP2
FFP2V
FFP20V
FFP3V
www.jsp.co.uk [email protected] [email protected] Call: 01993 826050 37
DISPOSABLE MASKS - RESPIRATORY PROTECTION
M05650 Maintenance Free (Disposable) A1P2 Maximask 2000 - Chapsmith 24
CODE DESCRIPTION CARTON QTY
Compliance Disposable Half MaskTwin fi lter disposable Half Mask suitable for use in heavy manual work
conditions. It features a rigid cradle harness fi tted and A1P2 fi lters fi tted.
Conforms to EN140
Moulded DisposableDust Mask- EN149:2001+A1:2009
FP1 - 111 • • • • • FFP1 Valved - 112 • • • • • • FFP1 Odour Valved - 113 • • • • • FFP2 - 121 • • • • • • • • FFP2 Valved - 122 • • • • • • • • FFP2 Odour Valved - 123 • • • • • • • • • FFP3 Valved - 132 • • • • • • • • • • • • •Flexinet - EN149:2001+A1:2009
FFP2 - 821 • • • • • • • • FFP2 Valved - 822 • • • • • • • • FFP2 Odour Valved - 823 • • • • • • • • • FFP3 Valved -832 • • • • • • • • • • • • •Vertical Foldfl at - EN149:2001+A1:2009
FFP1-211 • • FFP1 Valved.-212 • • FFP2-221 • • • • • • • • FFP2 Valved-222 • • • • • • • • FFP2 Odour Valved-223 • • • • • • • • • FFP3 Valved-232 • • • • • • • • • • • • •
Br
ick
Dust
Co
ncre
te
Fe
rros
Met
al F
ume
Fi
bre
Glas
s
Le
ad F
ume
M
DF H
and
Tool
s
M
iner
al F
ibre
s
Pl
aste
r
Ro
ckw
ool
Sa
ndst
one
Si
lica
W
eldi
ng
W
ood
Soft
W
ood
Hard
DISPOSABLE MASK PRODUCT SELECTOR
HALFMASKS™
Please contact sales dept for full Chapsmith® range.