ke - 150...edge protection: galvanised steel, stainless steel, profile thickness 6mm or cataphoretic...

www.polycon.co.uk0151 422 9747

Technical Data Sheet

Galvanised Edge Channel /Stainless Steel Edge Channel

Channel DrainageA15 to E600 loading

Level Invert or Sloped

KE - 150

Polycon Surface Water Drainage | KE - 150 Technical Brochure1 tel: 0151 422 9747 | email: [email protected] | www.polycon.co.uk

Stepped, Level, SlopedArea drainage with channel runs is normally made according to 3 different principles. The slops of water surface is achieved by the natural fall of the land. The water flows downwards with the gradient of the water level. A stepped invert is realised by an artificial gradient which is formed by the installation of stepped-height channels and connectors. The high flow rate with self-cleaning effect can be achieved with channels in natural slope. All slope types can be combined acording to hydraulic requirements and topographical conditions.

Stepped Invert

Level Invert

Sloped Invert

Technical Data SheetKE - 150

According to DIN 19580 / EN 1433 “Drainage channels for vehicular and pedestrian areas”, these surfaces are assigned to specific load classes depending on the use. Accordingly, the respective suitable Polycon reinforced edge system can be selected with the corresponding cover grating.

Also available in black cataphoretic dip coating

KE - 150Galvanised Steel / Stainless Steel edge rail

Channel Properties

Polymere concrete: Polyester resin-based with minergal aggregates, additives

Compressive strength: > 90 N/mm²

Bending tensile strength: > 22 N/mm²

Modulus of elasticity: ca. 25 kN/mm²

Density: 2.1 - 2.3 g/dm³

Heat resistence: 100°C (permenant loading)

Frost resistence: -50°C

Water penetration depth: 0mm

Water absorption 0.05%

Edge protection: Galvanised steel, stainless steel, profile thickness 6mm or cataphoretic black

Channel cover: Galvanised steel, V2A stainless steel, GJS cast-iron

1000mm214mm

h

500mm214mm

h h

1000mm

hh

214mm



KE - 150Channel Types Galvanised Steel / Stainless Steel edge rail

Article no. DesignationSlope

%

Length

cm

Width

cm

Height

(h)cm

Weight

kg

KE.150.0 KE - 150 Channel No. 0* 0 100 21.4 22.0 33.0

KE.150.0R KE - 150 Channel No. 0R*** 0 100 21.4 22.0 33.0

KE.150.005 KE - 150 Channel No. 005*/** 0 50 21.4 22.0 17.9

KE.150.1 KE - 150 Channel No. 1* 0.5 100 21.4 22.0 30.3

KE.150.2 KE - 150 Channel No. 2* 0.5 100 21.4 23.0 30.6

KE.150.3 KE - 150 Channel No. 3* 0.5 100 21.4 23.5 30.9

KE.150.4 KE - 150 Channel No. 4* 0.5 100 21.4 24.0 31.2

KE.150.5 KE - 150 Channel No. 5* 0.5 100 21.4 24.5 31.5

KE.150.6 KE - 150 Channel No. 6* 0.5 100 21.4 25.0 31.8

KE.150.7 KE - 150 Channel No. 7* 0.5 100 21.4 25.5 32.1

KE.150.8 KE - 150 Channel No. 8* 0.5 100 21.4 26.0 32.4

KE.150.9 KE - 150 Channel No. 9* 0.5 100 21.4 26.5 32.7

KE.150.10 KE - 150 Channel No. 10* 0.5 100 21.4 27.0 33.0

KE.150.010 KE - 150 Channel No. 010* 0 100 21.4 27.0 35.6


KE.150.0105 KE - 150 Channel No. 0105*/** 0 50 21.4 27.0 19.0

KE.150.11 KE - 150 Channel No. 11* 0.5 100 21.4 27.5 35.5

KE.150.12 KE - 150 Channel No. 12* 0.5 100 21.4 28.0 35.8

KE.150.13 KE - 150 Channel No. 13* 0.5 100 21.4 28.5 36.1

KE.150.14 KE - 150 Channel No. 14* 0.5 100 21.4 29.0 36.4

KE.150.15 KE - 150 Channel No. 15* 0.5 100 21.4 29.5 36.7

KE.150.16 KE - 150 Channel No. 16* 0.5 100 21.4 30.0 37.0

KE.150.17 KE - 150 Channel No. 17* 0.5 100 21.4 30.5 37.3

KE.150.18 KE - 150 Channel No. 18* 0.5 100 21.4 31.0 37.6

KE.150.19 KE - 150 Channel No. 19* 0.5 100 21.4 31.5 37.9

KE.150.20 KE - 150 Channel No. 20* 0.5 100 21.4 32.0 38.2

KE.150.020 KE - 150 Channel No. 020* 0 100 21.4 32.0 38.6


KE.150.0205 KE - 150 Channel No. 0205*/** 0 50 21.4 32.0 20.9

KE.150.150P KE- 150 Channel No. 150P**** 0 100 21.4 13.0 20.1

KE.150.150PR KE - 150 Channel No. 150PR***** 0 100 21.4 13.0 20.1

* Channel with mouldings for vertical outlet DA/0D 110** Channel with sidewise perforations for the connection of t-junctions, elbow joints and cross- over joints and vertical outlet*** Channel with vertical pipe socket DA/OD 110


Channel available in both Galvanised Steel or Stainless Steel



The KE - 150 system has a complete range of

accessories including a Sump Unit & Galvanised

bucket which can collect silt particles and has 110mm

and 160mm outlets for pipe connections

The system also has end caps and end cap outlets

with a 110mm pipe connector

Also available in black cataphoretic dip coating

KE - 150Sump & Accessories

Article no. DesignationLength

cm

Width

cm

Height

(h)cm

Weight

kg

KE.150.S KE - 150 Sump unit with dirt trap bucket 50 21.4 62 54.0

KE.150.PP.160 Pipe socket DA/OD 160 0.6

KE.150.PP.200 Pipe socket DA/OD 200 0.8

KE.150.CE.0205 KE - 150 Closed end cap for channel No. 0 - 0205 1.5

KE.150.CE.0 KE - 150 Closed end cap for channel No. 0 1.9

KE.150.CE.150P KE - 150 Closed end cap for channel No. 150-P 1.3

KE.150.EP.0 KE - 150 end cap with Pipe socket DA/OD 160 for No. 0 1.5



KE.150.EP.150P KE - 150 end cap with Pipe socket DA/OD 70 for No. 150P 1.5

KE.150.STEP KE - 150 Step connector for compensating level differences 0.5

h

500mm214mm

h

214mm

h

20mm

Accessories available in both Galvanised Steel or Stainless Steel



Slotted Grating OvalGrip Design


cm

Width

cm

Inlet Ø

cm²/m

Weight

kg

GR.150.MG.A Mesh grating. galvanised steel. MW 30 x 10 100 20 1240 9.8

GR.150.MG.A Mesh grating, galvanised steel, MW 30 x 10 50 20 1240 4.4

GR.150.MSS.A Mesh grating, stainless steel, MW 20 x 20 100 20 1240 9.5

GR.150.MSS.A Mesh grating, stainless steel, MW 20 x 20 50 20 1240 4.9

Gratings cl. C250 with SnapLock fastening

Mesh Steel Grating Slotted Grating SafeHeel

Longitudinal Grating

KE - 150Gratings


cm

Width

cm

Inlet Ø

cm²/m

Weight

kg

GR.150.MG.D Mesh grating, galvanised steel, MW 20 x 20 100 20 1240 9.8

GR.150.MG.D Mesh grating, galvanised steel, MW 20 x 20 50 20 1240 4.4

GR.150.MSS.D Mesh grating, stainless steel, MW 20 x 20 100 20 1240 9.5

GR.150.MSS.D Mesh grating, stainless steel, MW 20 x 20 50 20 1240 4.9

GR.150.ODI.D Slotted grating + OvalGrip Design, Ductile Iron, GJS 50 20 760 7.1

GR.150.LDI.D Longitudinal Grating, Ductile Iron , MW 25 x 11 mm 50 20 700 7.8

GR.150.SSDI.D Slotted SafeHeel Grating, Ductile Iron 50 20 700 7.6

Gratings cl. D4001 with SnapLock fastening

1 Exception: Cross-road drainage of busy roads



The SnapLock fastening is used for gratings for channels with nominal widths of 150 and 200 mm. SnapLock fastenings are optimised for the respective load class and combine safety and quality with functional design.

• Put in place - press on - snap in place

• Assembly without special tools

• Impervious to transverse forces

• Non-corrosive stainless steel springs

• Reliable function even when heavily soiled

• Grating and channel body intermesh to

form a sturdy unit

Benefits

SnapLock fastening



cm

Width

cm

Inlet Ø

cm²/m

Weight

kg

GR.150.MG.D Longitudinal Grating, Ductile Iron , MW 25 x 11 mm 100 20 1240 7.8

GR.150.MG.D Slotted SafeHeel Grating, Ductile Iron 50 20 1240 4.4

Gratings cl. E6001 with SnapLock fastening

1 Exception: Cross-road drainage of busy roads

KE - 150

PaveSlotOur Paveslots are specifically designed for intergration in high quality natural stone and paving surfaces. The discrete inlet slot enables effecient drainage without caccess trays for cleaning purposes.


All Polycon Paveslots come with either an offset slot or a centre slot aswell as having the choice of a twin slot or single slot

Available in both Glavanised Steel and Stainless Steel

KE - 150PaveSlot

Our Paveslots are specifically designed for intergration in high quality natural stone and paving surfaces. The discrete inlet slot enables effecient drainage without compromising the ground design. We offer both single & twin slotted paveslots aswell as access trays for maintenance purposes.

10mm

200mm

10mm

Offet Single Galvanised or Stainless Steel PaveSlot

1000mm

A Galvanised or Stainless Steel single slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.

60, 105, or 150mm Upstand

Centre Single Galvanised or Stainless Steel PaveSlot



10mm

200mm

1000mm

10mm

C250, D400Loading Upstand 60, 105 or 150


Width 200 mm mm

C250, D400Loading Upstand 60, 105 or 150Width 200 mm mm

60, 105 or 150 mm

60, 105 or 150 mm

KE - 150PaveSlot

60, 105 or 150 mm

Offset Twin Galvanised or Stainless Steel PaveSlot

A Galvanised or Stainless Steel Twin slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.




2 x 8mm

200mm

1000mm

Slots

60, 105 or 150 mm

Centre Twin Galvanised or Stainless Steel PaveSlot

A Galvanised or Stainless Steel Twin slot paveslot grating with a width of 200mm, available in either a 60, 105 or 150mm upstand.



200mm

1000mm

Slots

2 x 8mm Slots

2 x 8mm

Slots2 x 8mm

KE - 150PaveSlot

Galvanised or Stainless Steel Access Tray


200mm

500mm




Top View

60, 105 or 150 mm

End View

10mm

Article no. Designation Upstand Height (mm)

Overall Width (mm)

Slot Width (mm)

Length (cm)

Load Class

Weight (kg)

OS.1560.P.G Galvanised Offset Single PaveSlot 60 60 200 10 50/100 C, D 4.2



OS.1560.P.SS Stainless Steel Offset Single PaveSlot 60 60 200 10 50/100 C, D 4.4

OS.15105.P.SS Stainless Steel Offset Single PaveSlot 105 105 200 10 50/100 C, D 7.7

OS.15150.P.SS Stainless Steel Offset Single PaveSlot 105 150 200 10 50/100 C, D 11

Offset Single PaveSlot

PaveSlot Specs

KE - 150PaveSlot



Overall Width (mm)

Slot Width (mm)

Length (cm)

Load Class

Weight (kg)

CS.1560.P.G Galvanised Centre Single PaveSlot 60 60 200 10 50/100 C, D 4.5

CS.15105.P.G Galvanised Centre Single PaveSlot 105 105 200 10 50/100 C, D 8

CS.15150.P.G Galvanised Centre Single PaveSlot 150 150 200 10 50/100 C, D 11.4

CS.1560.P.SS Stainless Steel Centre Single PaveSlot 60 60 200 10 50/100 C, D 4.6



See the tables below for specifications on our paveslot gratings

Centre Single PaveSlot


Overall Width (mm)

Slot Width (mm)

Length (cm)

Load Class

Weight (kg)

OT.1560.P.G Galvanised Offset Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.6



OT.1560.P.SS Stainless Steel Offset Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.8



Offset Twin PaveSlot

KE - 150PaveSlot



Overall Width (mm)

Slot Width (mm)

Length (cm)

Load Class

Weight (kg)

AT.1560.P.G Galvanised Offset Single Access Tray 60 60 200 10 50 C, D 4.1



AT.1560.P.SS Stainless Steel Offset Single Access Tray 60 60 200 10 50 C, D 4.3



See the tables below for specifications on our paveslot

Access Tray PaveSlot


Overall Width (mm)

Slot Width (mm)

Length (cm)

Load Class

Weight (kg)

CT.1560.P.G Galvanised Centre Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.4



CT.1560.P.SS Stainless Steel Centre Twin PaveSlot 60 60 200 2 x 8mm 50/100 C, D 8.6

CT.15105.P.SS Stainless Steel Centre Twin PaveSlot 105 105 200 2 x 8mm 50/100 C, D 15

CT.15150.P.SS Stainless Steel Centre Twin PaveSlot 150 150 200 2 x 8mm 50/100 C, D 21.2

Centre Twin PaveSlot


Installation GuideGrounds condtions must be suitable and all dimensions shown are the minimum requirement. Engineering advice should be taken where necessary and any questions should be directed to Polycon’s technical team through emailing us at [email protected] or by calling us on 0151 424 9747

BlockPaving

1 2 3 4 5 6** Minimum Concrete Haunch

25 N/mm²

Concrete Sub Base EarthConcrete Haunch

Sand LayerExpansion

Joint

Detail AAllow for overbuild of 3mm to

5mm above the grating surfaces

Tarmac

Concrete PaveSlot

Z

YH2

Y

5 5

3

Z

Y

Y

H2

1 1

Z

Y

H2

Y

1

H2

Z

Y

Y

15 5

2

3

2

4

3

2

3

2

4

6

3

2

4

3

2

MORTOR

3

2

3

2

4

PAVING SLABBLOCK PAVE

Load Class A15 B125 C250 D400

H2 - Channel HeightChannel Height

Channel Height

Channel Height

Channel Height

Y - Minimum Surround 100mm 150mm 150mm 200mm

Z - Minimum Surround 100mm 150mm 150mm 200mm

T1 - Minimum Depth 40mm 40mm 40mm 40mm

T2 - Maximum Depth 95mm 55mm 55mm 55mm

Polycon Surface Water Drainage

Widnes Business Park, Foundry Lane, Widnes, WA8 8UB, England

Email: [email protected]: 0151 422 9747

Visit our website for our full range of products at www.polycon.co.uk

ke - 150...edge protection: galvanised steel, stainless steel, profile thickness 6mm or cataphoretic...

Documents