king oil tools -...

0413491

t KING OIL TOOLS

Oilfield SwivelsWater Well SwivelsSide Inlet Swivels

Power SwivelsWire Line Strippers

Circulating HeadsRotary Heads

ElevatorsTongsLinks

Hooks

KING OIL TOOLS КTable of ContentsGeneral Notes, Policy and Warranty 210-MB, 15-MB, 25-MB, 35-MB, and 50-MB Swivels 3-43-MB Swivel 575-WP Swivel 6-730-KG, 40-KG, 50-KG, and 60-KG Swivels 8-932-GAand 53-GA Swivels 10-1110-XV, 15-XV, 20-XV, 25-XV and 30-XV Swivels 12-1310-PXV, 15-PXV, 20-PXV, 25-PXVand 30-PXV Swivels 14-1525 HPA Swivel with Adjustable Packing 1620 XVA and 25 XVA Swivel with Adjustable Packing 172-KM, 10-KM and 15-KM Swivels 1825-WG and 15-KF Swivel 19ЗАРЕ Rotating Head 20Rotating Heads - 2.5 BLand 3 BL 211-J and 2-J Swivels 2210-JSS and 45-JSS Water Swivels ... 23

4.5-SI Side-Inlet Swivel and 5-EL and 5-PEL* Swivels 24Side-Inlet Swivels 256-CRC Swivel 265-KCOS Swivel 274-W Swivel Assembly 2815-PS Power Swivels 293-PS King Swivels 307.5 LW Swivel 314-SC, 5-SC, and 7-SC Circulating Heads 323-AR and 4-AR Wire Line Strippers 33Center Latch Collar Type Tubing Elevators 34Single Joint Elevators 35Center Latch 18 Degree Elevators 36SRA Sucker Rod Elevator/ 35 KRH and 20 KRH Rod Hook 37Elevator Links Weight and Dimensional Data 38KT Manual Tongs 39King Stuff / KPVC Slip 40

General Notes, Policy and WarrantyGeneral Notes on SwivelsBefore a swivel is purchased, careful consideration should be givento size, capacity requirements and speed at which it will be rotated.Other factors to be taken into account are overloading and shockloads.

The structural parts of all King Swivels, except Type J, are made ofhigh grade alloy steels. These parts are heat-treated to improve theirqualities. Type J housings are made of aluminum alloy or nickel iron.

All parts subject to stresses have safety factors that provide verywide margins beyond the safe limits indicated in the rating tables.(Read carefully the paragraphs dealing with bearings.)

Overloads and Shock LoadsAll swivels are frequently subjected to overloads and shock loadsunless a much larger swivel is used than is normally required.

Common causes of overloads: Using too long and too heavystrings of drill pipe. Also pulling on stuck pipe.

Shock loads result when the pipe is lifted suddenly. Severe shockloads are imposed when spudding gumbo off the bit. Probably theworst shocks of all are delivered by rotary jars when used forloosening stuck drill pipe.

Selecting a SwivelBefore deciding upon the type and size swivel to purchase, carefulconsideration should be given to the paragraphs concerningoverloads, shock loads and bearings.

When referring to the load capacity tables, it is best to select thenext larger swivel than is indicated in the tabulation. This will providesome insurance against damage resulting from overloads, shockloads and increases in speed of rotation.

Too frequently, a swivel is purchased to drill to certain depths;later, the operator will have occasion to drill deeper than wasanticipated. The swivel is overloaded as a result.

It is false economy of the worst sort to use a swivel that is too smallfor the job. Excessive cost of upkeep, plus shut down time of the rig,will soon amount to many times the added cost of a larger swivel.

Maintenance and RepairsLike any other piece of equipment, a swivel should be kept in goodrepair. It is our rigid policy to give first attention to repair orders, and

repair replacement parts are almost invariably shipped the same dayan order is received.

When a King Swivel is in need of repairs, other than repacking, itshould be returned to us if at all possible. We can usually repair itmore economically than anyone else, because we are able to reclaimmany expensive parts that would otherwise be discarded.

The greatest advantage in returning your King Swivel to us forrepair is the fact that when it is a factory job, the owner may feelassured that the various parts fit correctly and that adjustments areproperly made.

Cancellations, Claims and ReturnsOrders for specially-designed products or standard products ofspecial size and/or materials are not subject to cancellation afterhaving been received at our factory.

No rubber goods may be returned in excess of 60 days fromdelivery date. No return on rubber goods shipped overseas will beaccepted.

No products, materials or parts will be accepted or credited orreplaced without the written consent of the factory. After writtenpermission for such return is granted in writing by King Oil Tools, thematerial is subject to a restocking charge. No material will beaccepted for credit after one year from date of purchase.

Limited WarrantyEvery reasonable effort is made to guard against defective materialor workmanship entering into the products of King Oil Tools.However, in the event of failure of a defective part, within one year ofpurchase, our entire liability is limited to the value of, or replacementof, such defective part within that time. King Oil Tools expresslydisclaims liability for incidental or consequential damages. Anymodification to products as manufactured voids any expressed orimplied warranty.

No warranty is given on parts that are normally subject to rapidwear, such as packing, washpipes, wear bushings, stripper rubbers,springs, bearings, etc.

King Oil Tools will not be responsible for bodily injury, loss of life orproperty damage, if such should occur in connection with the use ofits products. Seller's total responsibility for any claims, damages,losses or liabilities arising out of or related to all products coveredhereunder shall not exceed the purchase price of the product.

King Oil Tools, 2215 S. Van Buren, Enid, OK 73703Phone: (580) 234-4141 U.S. Wats: 800-759-7441Fax: (580) 233-6807 [email protected]

KING OIL TOOLS

10-MB, 15MB, 25-MB, 35-MB, and 50-MB Swivels

К

GOOSENECKLarge watercourse and heavy walled forsmooth flow & longevity.

WASHPIPEHardened and ground finish; "floating" toassure alignment with packing.

QUICK CHANGE PACKINGReplaceable as cartridge without gooseneckremovable; high pressure.

SEALDouble-acting upper and lower seal.

MAIN BEARINGLarge tapered roller sized to API Spec.

LUBRICATIONLarge oil cavity and design assures allbearings are flooded with cool oil.

ALIGNMENT BEARINGUpper and lower straight roller widely spacedto insure stem alignment.

STEMForged, alloy steel for long life, extra long forre-threading.

ModelStatic CapacityRotating Capacity100RPMAPIWorking Pressure (PSI)Bail Diameter at BendBail Radius for HookHook ClearanceFluid PassageGooseneck ConnectionSpindle Thread Conn.Saver Sub ThreadWashpipe Packing

Upthrust BearingMain BearingAlignment BearingsOil CapacityWidthLength Less SubWeight Less Oil

10MB120 Tons

78 Tons45004V4"

4"

17'/2"

3"

3" Female4V2 EUE 8 RD41/S" API Reg.Pressure Seal

Lip TypeBall

Tapered RollerStraight Roller

2.5 Gal.20"

69 '/г~

1950

15MB150 Tons

97 Tons4500

5"

41/2"

20V16"3"

4" Female41/2 API FH

6W API Reg.Pressure Seal

Lip TypeBall


4.5 Gal.26"

64 '/•"2750

25MB300 Tons

193 Tons45005%"4W24"3"

4" Female5% API Reg.6W API Reg.Pressure Seal

Lip TypeBall


7 Gal.30 Va"

93"3960

35MB400 Tons

258 Tons4500вЗ/4"

4№"

24"

3"

4" Female6% API Reg.6WAPIReg.Pressure Seal

Lip TypeBall


10 Gal.35"

97 V«"4500

50MB550 Tons

367 Tons450071/2"4'/2"26"3"

4" Female6% API Reg.6=/* API Reg.Pressure Seal

Lip TypeBall


11 Gal.40 W

103 "A."5900

KING OIL TOOLS

10-MB, 15-MB, 25-MB, 35-MB, and 50-MB SwivelsК

10 МВ-ЗА 15 МВ-ЗА UPPER PACKING FLG

10 MB-347 O-RING SEAL

10 MB-353 O-RING SEAL10 MB-9A BOTTOM RING

10 MB-9E UPPER RING

10 MB-25 WWSHPIPE


10 MB-9D UPPER RING

10 MB-9C GREASE RING

10 MB-3 PACKOFF BOX

SEC. & THIRD RING 10 MB-9B

10 MB-20 PACKING (5)

10 MB-9A BOTTOM RING


10 MB-358 O-RING SEAL10 MB-5 SPINDLE ADAPTER

MB Swivel Packing InstructionsRemoval

Bring swivel down to a safe working height, stop rotation, and mud circulation.Unscrew and remove the four (4) bolts, item #27. These are the bolts on the bail side of the Bonnet.Unscrew and remove the six (6) bolts, item #29.Collapse packing assembly by prying the Upper Packing Flange down, MB-03A of packing box drawing.Remove packing assembly, item #6.Install new 0-ring, item #24.Install new or refurbished packing assembly, item #6.Install the four (4) bolts, item 27 and tighten equally and in opposing directions. ALWAYS TIGHTEN FIRST.Pry the bottom half of the packing assembly down. Install and tighten the six (6) bolts, item #29.Grease the packing through the jerk fitting of the MB-03, Packing Box.Close Kelly cock and pressure test to 5000 PSI or less. Note: A pressure of greater than 1000 P.S.I. is requiredto seat the single piece of packing in the upper packing flange. If this is not done, a leak could be present in thearea of the upper packing flange.If no leaks are present begin drilling.

IV. To Refurbish A Removed Packing Assembly.Disassemble the old packing assembly and clean all removed metal parts.Inspect and replace all metal parts that are damaged and/or show excessive wear.Install one piece of 10mb-20 Packing into the Bottom Ring,10MB-09A.Install 0-ring,10MB-358 into outer 0-ring groove of this Bottom Ring.Install two (2) pieces of 1 OMB-20 Packing into each one of the Middle Rings,1 OMB-09BInstall packing into the Grease Ring,1 OMB-09C.On a flat surface place the Bottom Ring,10MB-09A with packing up and install one of the Middle Rrings, 10MB09B with Packing up.Install the other Middle Ring,1 OMB-09B with Packing up.Install the Grease Ring,10MB-09C with Packing up.Install the Upper Ring,10MB-09D.Install one of the 0-rings,10MB-347 into the 0-ring groove in top Upper Ring,10MB-09D.Slide the Packing Box 15MB-03 on this assembly.Place the Upper Packing Flange onto the top of the Packing Box.Install the last piece of packing.1 OMB-20 into the Bottom Ring 10MB-09E.Install the Upper Lock Ring,10MB-09E onto this Bottom Ring.

15. Install this assembly (Bottom Ring, Packing, and Upper Lock Ring) onto the short side of the Washpipe,Note: Check to make sure the extensions of the Upper Lock Ring slips onto the flats provided on the Washpipe,10MB-25.

16. Slide the Washpipe with this assembly into the Upper Packing Flange and through the assembled packing box.Some force might be required.

17. Turn completed Packing Assembly on its side and install the 0-ring,1 OMB-347 into the 0-ring groove of theUpper Bottom Ring and wire the packing Assembly together. Store for future use.

Note: All other services not included in the above are considered mayor repairs and should be done by an authorizedservice center.

Swivel Size

10MB*

15MB25MB

35MB

A

69Vz64Ve

9397Vie

В

3548%543/4

54S/1B

С

4'A5

5%63/4

D

17Vz

20Via24'A

24

E

16Va

9%

17V4

171/2

F

20

26

30</г35

G

14

Ша20Va23'/2

H

2Vz3Vs

45

*10MB has bottom pin connection.

KING OIL TOOLS К3-MB Swivels

For Mineral Exploration—Deep Water Wells.The 3-MB swivel is rugged, compact, and dependable. Made of high-grade alloy steel, ithas a high capacity proportionate to its weight.

The packing unit consists of a stuffing box and chevron or V-type packing. The entirepacking assembly can be replaced within a few minutes without "breaking-out" anyconnection.

Built to "oil field standards", the swivel features an upper taper bearing, spherical rollermain bearing, and a lower radial ball bearing. A bearing adjusting nut is standard. Thisconstruction makes this swivel more dependable and more rugged than any existingswivel now offered by rig manufacturers.

Four large trunion pins are provided for rigs equipped with pull-down yokes. Two-inchtrunion pins are standard. The 10%" shoulder dimensions of the pins allows replacementin existing rigs equipped with yokes.

Features in Brief• Large watercourse to permit circulating more drilling fluid.• Oil lubrication of bearings.• Oil seals to retain fluid and protect bearings.• Bearing adjusting nut.• Chevron packing and washpipe easily changeable without breaking connections.

Weight and Dimensional Data

Lower Connection (Kelly)

27/8" API IF LH pin

ЗУг" API IF LH pin

WeightPounds

410

410

Length

39W

39Ve"

HoseConnection

3" NPT3" NPT

DiameterWatercourse*

21/e"

2%'

BallOpening

7" x 9"

7" X 9"

Capacity and Safety DataCapacity, IDS, at

100 RPM

60,000

Static LoadIbs.

100,000

PulldownIbs.

30,000

Safe Depths (Feet) With Drill Pipe2%' 6.65 Ibs.

8500'

2W 10.4 Ibs. 3W 13.3 IbS. W 16.6 IbS.

5500' 4000' 3500'

Type 3-MB Swivel and Parts

PartNumber

3-MB-1

3-MB-23-MB-3

4-RC-2503-MB-43-MB-2683-MB-73-MB-8

3-MB-4433-MB-93-MB-11

3-MB-123-MB-143-MB-16

50-KG-1950-KG-2050-KG-2150-KG-22

3-MB-24

50-KG-2575-WP-339

4.5 SI-263-MB-273-MB-30R3-MB-313-MB-263

3-MB-333-MB-343-MB-351

Name of Part

Bail

Packing Box ScrewsPacking BoxPacking Box "O" RingBonnetLower Bonnet "O" RingUpper Seal

Upper Bearing NutAdjusting Nut "O" Ring

Bearing Adjusting NutUpper BearingMain Bearing

Bearing HousingSwivel StemPacking Gland

PackingLantern RingPacking Seat Ring

Packing Adjusting Gland

WashpipeWaspipe "O" Ring

Lower Alignment BearingLower SealLower Bearing NutLower Seal BoxLower Seal Box "O" Ring

Bonnet Socket ScrewsLower Seal Box Cap ScrewsLower Bearing Nut "O" Ring

No.Required

1

41

11

1

21

111

1

1

11

1 set1111111111

1061

Weight

751

12V2

Ve65

Ve

%5

Ve7

12

21

85

79

2

V2

1

V2

85

—

4

V2

2V2

9V2

Ve

V2

V2

Ve

*Watercourse size depends on tool joint size.

75-WP Swivel

KING OIL TOOLSкFor Drilling Medium Depth Oil Wells • For Deep Slim Hole Drilling For the HeavierWork-Over Rigs • For Drilling Deep Water WellsThis swivel is sturdier than the other types of King Swivels, but like those other types it hasa very high ratio of capacity to weight.

FOREIGN OPERATORS should find this swivel attractive because it can be more readilytransported than other, heavier swivels having comparable capacity.

The 75-WP Swivel is available with the CONVENTIONAL BAIL, or it will be furnished withan ELEVATOR SHANK in lieu of a bail.

ALLOY STEEL is used throughout in the manufacture of this swivel, except that someminor parts are of bronze where that metal is more suitable.

THE BEARINGS ARE ANGULAR-CONTACT TYPE BALL BEARINGS. The thrust bearingis a unit of four bearings mounted tandem. These bearings are flush ground and matchedat the factory to assure that each bearing will carry its share of the load. Reverse loads areabsorbed by a single Angular-Contact bearing mounted opposed to the main thrust unit.The manner in which the bearings are mounted will provide ample radial stability for theswivel.

The Swivel Housing is provided with automatic grease seals. These seals retain thebearing lubricant. A good grade of ball bearing grease should be injected, with a greasegun, once or twice per location.

The Packing unit consists of stuffing box, washpipe, V-type or chevron-type packing,O-rings, latern rings and packing gland with zerk grease fitting which simplifies packinglubrication.

The packing is quickly and easily adjusted by tightening the bronze adjusting ring.Repacking can be accomplished in a very few minutes by this six-step procedure:(1) Rotate packing box to align with square on washpipe, raise packing box over wash-pipe squares, then rotate packing box 6 turns to right to disengage washpipe. (2) Removeadjusting ring and unscrew washpipe. (3) Remove complete packing unit and washpipe.(4) Replace seat, packing, lantern rings and gland. (5) Replace washpipe and insert packing box with packing assembly. (6) Replace adjusting ring.


TVpe Swivel

75-WP with 41/7 connection75-WP with 6W connection

Type Swivel

75-WP with 41/z" connection75-WP with 6W connection

Weight, Pounds

740 Ibs.800 Ibs.

Kelly Connection

41/2" API-LH6%" API-LH

Length, Inches

65"

66"

Hose Connection

3" NPT3" NPT

Width, Inches

1 1 Vf1 1 W

DiameterWater Course

21/2"

21/2"

Ball Opening

8" x 1 8"8"x 18"

Weight BoxedFor Export

920 Ibs.980 Ibs.

Capacity and Safety Data

Capacity, Lbs. at 100 R.P.M.

100.000

Safe Load Limits, Lbs.

250,000

V№

10.40 Ib.9,200'

Safe Depths (Feet) With Drill Pipe3$

13.30 Ib.6,000'

41/2"

16.60 Ib5,000'

KING OIL TOOLS К75-WP Swivel

75 WP-1, Bail75 WP-1E, Elevator Shank (optional)75 WP-3, Gudgeon Retainer Screw75 WP-2, Gudgeon Pin75 WP-4, Gooseneck

75 WP-5, Felt Washer75 WP-6, Upper Housing Seal75 WP-7, Upthrust Bearing75 WP-8, Bearing Spacer75 WP-9, Oownthrust Bearings75 WP-10, Bearing Housing75 WP-11, Bearing Lock Nut75 WP-12, Lower Housing Seals75 WP-335, "O" Ring75-WP-13, Washpipe75 WP-17, Packing Box75 WP-16A, Packing Seat Ring75 WP-16B, Lantern Ring75 WP-15, Packing75 WP-16C, Packing Gland75 WP-342 "O" Ring75 WP-339, "O" Ring75 WP-18, Clamp Screw75 WP-20, Adjusting Nut Clamp75 WP-19 Adjusting Ring75 WP-14, Lower Housing

—-U— L J

Parts List for 75-WP Swivel

PartNumber

75WP

75WP-175WP-1E75WP-275WP-375WP-475WP-575WP-675WP-775WP-875WP-1075WP-1175WP-12

Name of Part

Swivel with 4V2" PinCompleteSwivel with 65/в" PinCompleteBailElevator ShanktBail Gudgeon PinGudgeon Retainer ScrewGooseneckFelt WasherUpper Housing SealBearingBearing SpacerBearing HousingBearing Adjust NutLower Housing Seal

NumberRequired

11121

11

511

1

2

NetWeightPounds

740

800126

135

13

V8(2)166

Vie3/4

14

3

134

17

'/2(2)

SparesFor one

Year

1111

2

PartNumber

75WP-13

75WP-33575WP-1475WP-1575WP-16A75WP-16B75WP-16C75WP-1 775WP-1875WP-1975WP-33975WP-2075WP-342

Name of Part

Washpipe

"O1 RingLower housingPackingPacking Seat RingLantern RingPacking GlandPacking BoxClamp ScrewAdjusting Ring"O' RingAdjusting Nut Clamp'O' Ring

NumberRequired

1

11

1 set111141

1

21

NetWeightPounds

4

Vie149'/2

V2

1

1V2

13

1 (4)17V3

V,e2(2)

v,6

SparesFor one

Year

5

2

10 sets2221212

2

fWhen ordering Swivel with Elevator Shank, state size of elevator.ifDownthrust Bearings should always be replaced with a full matched set. Never renew one or two bearings in an old set.

KING OIL TOOLS

30-KG, 40-KG, 50-KG, and 60-KG SwivelsК

MODEL 50 KG

KG-16

6CRC-260

60KG-27

60KG-29

60KG-760KG-26

60KG-8

60KG-16

For Drilling Relatively Shallow Oil Wells, the Deepest of Water Wells, Workover Rigs,Slim Hole Drilling and "Drilling In" and Coring Oil Wells by the Reverse CirculationMethod.King 30, 40, 50, and 60-KG swivels provide the same oversize watercourse as the King XVseries, and also feature a wash pipe with adjustable chevron or V-type packing.

They are streamlined and compactly constructed. They are made of high grade alloysteels and have very great capacities, proportionate to their weights.

The Bearings are angular-contact type ball bearings. Weight of the drill pipe (downthrust)is carried on quadruplex units. The four bearings in this unit are flush ground, on their faces,and matched so that each bearing will support its share of the load.*

Reverse loads (upthrusts) are absorbed by a single bearing that is mounted opposed tothe quadruplex unit.

The type of bearings used and the manner in which they are mounted provide ampleradial capacity to stabilize the swivels.

The packing unit consists of a stuffing box and chevron or V-type packing.These swivels can be repacked, within a very few minutes, without 'breaking out' any

connection. The entire packing assembly can be replaced in ten minutes or less. It is notnecessary to remove any other part of the swivel to repack. This eliminates the possibility ofthread-galling.

Because of the large oversize watercourse and packing arrangement, these swivels areideally suited for both conventional and reverse circulation methods.

Features in Brief• ALLOY STEELS assures strength with minimum weight.• OVERSIZE WATERCOURSES permit circulation of more drilling fluids.• MULTIPLE BALL BEARING UNITS provide ample thrust and radial capacities.*• SEALED HOUSING protect the bearings and retain lubricant.• GREASE LUBRICATION OF THE BEARINGS is accomplished through a readily

accessible fitting.• CHOICE OF CONVENTIONAL BAIL OR ELEVATOR SHANK.• ZERK FITTING in stuffing box simplifies lubrication and greatly prolongs life of

chevron-type packing.• PACKING COMPONENTS AND ASSEMBLIES ARE INTERCHANGEABLE in Types 30-,

40-, 50- and 60-KG swivels.These swivels are furnished with a conventional ball or a plain elevator shank, at the

option of the purchaser. Shanks, for use with more than one size elevator, will be furnishedto order at an extra cost. Shanks can be furnished for use in connection with "bottleneck"elevators.

Kelly connection on the 30-KG Swivel is 41/2", 8-V, left-hand thread, VTPF drill pipe. Thisaccommodates a 3" watercourse through the swivel.

Kelly connection on the 40-KG Swivel is 3Vz" API Specification, Full Hole Pin, Left HandThread. If a three-inch watercourse is required, through the swivel, а 41/г" left hand, drillpipe thread will be substituted, for the tool joint pin, at no extra charge.

Kelly connection on the 50-KG and 60-KG Swivels is 41/г" API, Regular Tool Joint Pin, LeftHand Thread. If three-inch watercourse is required, a 65/s" Regular, Left Hand Pin, will befurnished at extra cost.

When a swivel is purchased, an extra set of packing and a hardened and groundwashpipe should be bought. The swivel should never be in operation without these extraparts on hand.

These swivels are designed to operate efficiently at relatively high rotating speeds.

*The 60-KG Swivel features tapered bearings.

MODEL 60 KG

KING OIL TOOLS

30-KG, 40-KG, 50-KG, and 60-KG Swivels

КCapacity and Safety Data*

Type Swivel

30-KG40-KG50-KG60-KG

Capacity, Lbs.at 100 ft. P.M.

44,000*54,000'65,00088,000

Static LoadLimit, Lbs.

95,000140,000160,000160,000

Safe Depths (Feet) With Drill Pipe

2W6.65LD.6,4008,000

10,000

2W10.4Lb.

4,0005,0006,200

3W 1 3.3 LB.

3,4003,8004,800

4V2" 16.6 Lb.

2,6003,0003,805

(A.RI. Haling)

*Non oilfield rating,

Type Swivel

30-KG40-KG40-KG50-KG50-KG60-KG

Lower (Kelly) Connection

4V'2" D.8-V, L.H., 3/4" TPFЗУ2" API FH. Pin L.H.4У2" D.8-V, L.H., 3/4" TPF4V'2" API Reg. Pin, L.H.6%" API Reg. Pin, L.H.6W API Reg. Pin, L.H.

WeightPounds*

225

347

347

512

593

625

LengthOverall

45"

57"

57"

63"67"

71"

WorkingLength

37"

50"

50"

55"59"

59"

HoseConn.

3" NPT3" NPT3" NPT3" NPT3" NPT3" NPT

DiameterWatercourse

3"

21/2"

3"

21/2"

3"

3"

BailOpening

5" x 8" or 6" x 14"6"x14"6"x14"7"x16"7"x16"7"x16"

Parts List for Type KG King Swivels

Name of Part

BailBail (6" х14")'Elevator ShankBail Gudgeon PinBail Pin NutsGooseneckHousing SealsHousing SealsBearing SpindleShield SealBearing ShieldBearing Retainer WireBearingBearing HousingHousing Lock BoltSpindle Thread Seal"O" Ring"0" Ring"O" RingStuffing BoxPacking GlandPackingLantern RingPackety Seat RingAdjusting Lock NutAdjusting ScrewWashpipe

NumberRequired

111121

1

21

11

1

1 set11111111

1 set11221

PartNumber

30KG-132GA-1030KG-1E*32GA-1132GA-11A30KG-430XV-7

30KG-830XV-930XV-1030XV-1130XV-1230KG-1450XV-1550KG-1775WP-33950KG-34450KG-34650KG-1850KG-1950KG-2050KG-2150KG-2250KG-2350KG-2450KG-25

30-KG

NetWeightPounds

26

32

48

6'/4

2(2)64

'/2

18

V23/4

Vie26(4)

40

V4

VaVa

Va

'/8

12'Л2

V2

1

V2

1/4

V2

4V2

SparesFor one1 Year

2

1

1 set

22

21

1

6 sets11

3

PartNumber

40KG-1

30KG-1E*40KG-250KG-2A40KG-44SO7

40KG-830XV-930XV-1030XV-1 130XV-1240KG-1450XV-1550KG-1775WP-33950KG-34450KG-34650KG-1850KG-1950KG-2050KG-2150KG-2250KG-2350KG-2450KG-25

40-KG

NetWeightPounds

52

30

62

113/4

3(2)87

'/2 (3)

23V2V23/4

Vie34(5)

631/4

VaVaVeVa

12V4

21/2

1

1/2

V4

V2

4V2

SparesFor one

Year

3

1

1 set

22211

6 sets11

3

PartNumber

50KG-1

50KG-1E50KG-250KG-2A50KG-430XV-750KG-750KG-850XV-950KG-1050KG-1150KG-1250KG-1450XV-1550KG-1775WP-33950KG-34450KG-34650KG-1850KG-1950KG-2050KG-2150KG-2250KG-2350KG-2450KG-25

50-KG

NetWeightPounds

74

73

14V2

3(2)129

V4

3/4 (2)39

V,e

'/в

Va46(5)

85

'/4

Va

VaVB

Va12V4

2Vs1

'/2

V4

Vz4V2

SparesFor one

Year

12

1

1 set

22211

6 sets11

3

fSOKG requires one 30XV-7 Upper Housing Seal and two 50XV-7 Lower Housing Seals.JDownthrust Bearings should always be replaced with full matched sets.

Parts List for 60-KG King Swivel

PartNumber

50KG-1SOKG-250KG-360KG-460KG-760KG-84.5SI-103MB-1160KG-1260KG-1460KG-1650KG-1850KG-19

Name of Part

BailBail PinBail Pin NutGooseneckHousing SealSpindleHousing SealUpper BearingMain BearingBearing HousingLower ConnectionStuffing BoxPacking Gland

NumberRequired

1121111111111

NetWeight,Pounds

75152(2)

130|A

85

V4

12

2585

7612V4

2

Sparesfor One

Year

————1_111

——11

PartNumber

50KG-2050KG-2150KG-2250KG-2450KG-2560KG-2660KG-2760KG-2860KG-2960KG-306CRC-26075WP-33950KG-34450KG-346

Name of Part

Packing SetLantern RingPacking Seat Ring

_ Adjusting Screw w/NutsWashpipeLower Wear SleeveLower Oil BoxLower BearingCap ScrewsUpper Wear Ring"0" Ring (Oil Box)"0"Ring (Washpipe)"O" Ring (Pkg. Gland)"0" Ring (Pkg. Gland)

NumberRequired

11121111611111

NetWeight,Pounds

1/21

1/2

11/2(2)

41/22№6

12116)2

1/4

1/4

1/4

1/4

Sparesfor One

Year

611_3_——__1322

KING OIL TOOLSК32-GA and 53-GA Swivels

For Drilling Shallow Oil Wells, Core Drilling, Slim Hole Drilling and Working Over OilWellsThe GA Swivels have been very popular for many years. They have proved to be rugged,dependable and durable. They are in use around the world for drilling shallow oil wells,exploration drilling, water well drilling and on lease service jobs.

The bearings are angular-contact type ball bearings. Weight of the drill pipe (down-thrust) is carried on quadruplex units. The four bearings are flush ground, on their faces,and matched so that each bearing will support its share of the load.

Reverse loads (upthrust) are absorbed by a single bearing, in the 32-GA, and a duplexset in the 53-GA. These upthrust bearings are mounted opposed to the quadruplex units.

The type of bearings used and the manner in which they are mounted provide ampleradial stability for the swivels.

These swivels are furnished with either a bail or elevator shank, at the option of thepurchaser.

Features in Brief• ALLOY STEELS assure strength with minimum weight.• PACKING is V-type, often called chevron type.• WASHPIPES are seamless alloy tubes, casehardened and ground.• GREASE LUBRICATION for the packing.• MULTIPLE BALL BEARING UNITS provide ample capacity.• OIL BATH LUBRICATION for the bearings.• Choice of BAIL OR ELEVATOR SHANK.

Type GA SwivelPatentedWith Ball

Weights and Dimensional Data

туре32-GA53-GA

WeightPounds

170

340

LengthOverall

42"

52"

WorkingLength

35"

45"

Lower Conn., DrillPipe Thread, L.H.

3VTO.D., 8-V41/2"O.D., 8-V

HoseConnections

2" NPT

21/2" NPT

SizeWashpipe

1 Vf2"

BailOpenings

6"x14"

7'/2"x18"


Type Swivel

32-GA53-GA

Capacity, Lbs.at 100 R.P.M.

39,00060,000


80,0001 20,000

Safe Depths (Feet) With Drill Pipe

2%" 6.65 Lb.

3,9006,000

27/e"10.4Lb.

2,6004,000

31/2"13.3Lb.

2,0003,100

4W Lb.

2,400Be sure to read the paragraphs on overloads, shock loads and bearings on page 5210.

10

KING OIL TOOLSт

К32-GA and 53-GA Swivels

32GA-253GA-232GA-1653GA-1632GA-1753GA-1732GA-1853GA-18

32GA-1953GA-1932GA-353GA-332GA-553GA-532GA-653GA-632GA-753GA-732GA-853GA-8

Parts List for Type 53-GA King Swivel

PartNumber

53GA53GA-153GA-253GA-353GA-453GA-553GA-653GA-753GA-853GA-953GA-1053GA-10E53GA-1 132GA-11A20XV-9A53GA-14S3GA-1553GA-1653GA-1853GA-19

Name of Part

Swivel CompleteGooseneckOuter HousingBearing HousingHousing Lock NutPacking GlandGland Bolts and NutsLantern RingPackingWashpipeBailElevator ShankfBail GudgeonGudgeon Retainer NutsFelt WasherUpper Housing SealBearing:}:Bearing SpacerBearing Lock NutLower Housing Seal

NumberRequired

11

1

1

1

2 each1

1 set1

1

11

2

1

1

1 set (6)1

1

2

Net WeightPounds

340*7051

74

13V2

4

1Va(2)3Л3/4

6>/4

53

65

10

1 Va (2)

'/32

V2

25

'/2

47/8

1V8(2)

Spares forOne YearService

1

21

6 sets3

11

1 set

2* Swivel boxed for export weighs approximately 410 pounds.fState size Elevator when ordering Shank.JDownthrust bearings should always be replaced by full matched sets. Never renew one or two bearings i

Parts List for Type 32-GA King Swivel

PartNumber

32GA32GA-132GA-232GA-332GA-432GA-532GA-632GA-732GA-832GA-932GA-1032GA-10E32GA-1 132GA-11A1 5XV-9A32GA-1432GA-1532GA-1632GA-1832GA-19

Name of Part

Swivel CompleteGooseneckOuter HousingBearing HousingHousing Lock NutPacking GlandGland Bolts and NutsLantern RingPackingWashpipeBailElevator ShankfBail GudgeonGudgeon Retainer NutsFelt WasherUpper Housing SealBearing}:Bearing SpacerBearing Lock NutLower Housing Seal

NumberRequired

11

1

11

2 each1

1 set1

1

1

1

21

1

1 set (5)111

Net WeightPounds

170'37V2

24

34

5

25/8

1(2)

V2

3/8

3'/8

32

46

6V2

1(2)

'/323/e

12

%

3V43/e


1

2

1

6 sets3

1

1

1 set

1

* Swivel boxed for export weighs approximately 220 pounds.fState size Elevator when ordering Shank.:j:Downthrust bearings should always be replaced by full matched sets. Never renew one or two bearings in an old set.

The bearings in the 32-GA and 53-GA swivel should be lubricated with a medium weightoil of good quality. Packing boxes are equipped with a grease fitting, and packing shouldbe lubricated often with water pump grease.

11

KING OIL TOOLS

10-XV, 15-XV, 20-XV, 25-XV, and 30-XV SwivelsКA

XV-1XV-1E

Light Swivels for Circulating Large Volumes of Fluid, for DrillingWater Wells, Geophysical Drilling and Core DrillingThese five sizes of XV Swivels were designed to fulfill a need for small, light duty swivelsthat would facilitate circulation of more drilling fluid than conventional models. They areshort, compact and require but little space.

These swivels, except the 10-XV, can be equipped with elevator shanks.The bearings are angular-contact type ball bearings. Weight of the drill pipe (down-

thrust) is carried on a triplex unit. The three bearings in this unit are flush ground, on thefaces, and matched so that each bearing will support its share of the load.

Reverse loads (upthrust) are absorbed by a single bearing that is mounted opposed tothe triplex unit.

The type of bearings and the manner in which they are mounted provide ample radialcapacity and stabilize the swivels.

The packing unit consists of two molded, composition rubber rings. An extremely hardwear ring (wear bushing) is placed between the two rubber rings. These rubber rings andthe wear bushing replace the washpipes and stuffing boxes that are used in conventionalswivels.

These swivels can be repacked, within a very few minutes, without 'breaking out' anyconnections. Adjustment of the packing is not required, and no means of adjustment isprovided.

THE 10-XV SWIVEL is applicable to small water well, geophysical and core drilling rigs.This swivel has a stiff bail.

THE 15-XV SWIVEL is suited to medium size water well, geophysical and core drillingrigs.

THE 20-XV SWIVEL operates efficiently on medium large water well, large core drillingand geophysical drilling rigs.

THE 30-XV SWIVEL is ideal for large water well rigs and is extremely useful when ream-ing down for pit and underreaming, prior to graveling operations. Centrifugal pumps arefrequently used for circulating through this swivel.

This swivel is not recommended for high speed rotation because the large diameterpacking may fail, due to generation of frictional heat.

Instructions for LubricatingThere is a grease fitting set in a recess, near the bottom of the bearing housing. This fittingis to lubricate the bearings.

Use only a good grade of neutral mineral grease that is free of all substances such asgraphite or mica. Either soda soap base or lime soap base greases are satisfactory.

Lubricate every two to three hundred hours of operation. If too much grease is used, theexcess will squeeze out past the upper housing seal.

A slight amount of grease may be thrown from the swivel when new, and after each timeit is lubricated. This is of no consequence.

BE SURE TO READ THE PARAGRAPHS ON OVERLOADS, SHOCK LOADS AND BEAR-INGS ON PAGE 2

Features In Brief• ALLOY STEELS assure strength with minimum weight.• OVERSIZE WATERCOURSES permit circulation of more drilling fluids.• MOLDED RUBBER COMPOSITION PACKING eliminates the usual stuffing boxes.• HARDENED WEAR BUSHINGS eliminate conventional washpipes.• PACKING AND WEAR BUSHINGS are quickly renewable.• MULTIPLE BALL BEARING UNITS provide ample thrust and radial capacities.• SEALED HOUSINGS protect the bearings and retain lubricant.• GREASE LUBRICATION OF THE BEARINGS is accomplished through a readily accessi-

ble fitting.• CHOICE OF CONVENTIONAL BAIL OR ELEVATOR SHANK.

XV-17—Spindle Thread Seal isinserted between Spindle Nut

and Spindle

To Repack Swivel: (1) remove housing lock bolt. XV-15; (2)unscrew bearing housing, XV-14, five turns off gooseneck, XV-4.This is a left hand thread. Do not back off more than five threads;(3) remove two packings, XV-5, and wear bushing, XV-6; (4) insertnew parts and (5) screw housing back tight, then replace lock bolt.This completes repacking.Note: Trunion pins can be added to use on pull down rigs.

12

KING OIL TOOLS

10-XV, 15-XV, 20-XV, 25-XV and 30-XV Swivels

КParts List for Type 10-XV Swivel

PartNumber

10XV-410XV-510XV-6

10XV-7

10XV-810XV-910XV-1010XV-11

10XV-1210XV-1410XV-15

10XV-1610XV-17

Name of Part

Gooseneck

PackingWear Bearing

Housing SealSpindle Nut

Shield SealBearing Shield

Bearing Retainer WireBearing^

Bearing HousingHousing lock Bolt

SpindleSpindle Thread Seal

NumberRequired

121

2

11

11

1 set (4)1111

Net WeightPounds

17

VeHV4

V4(2)2VeV4

VIB4Vs9V2

Ve7

Spares forOne Year

822

1 set

2

Parts List for Type 15-XV Swivel15XV-1

15XV-1E15XV-2

15XV-2A15XV-415XV-5

15XV-615XV-7

15XV-815XV-915XV-1015XV-11

15XV-1215XV-14

15XV-1515XV-161 5XV-1 7

Bail

ElevatorShanktBail Gudgeon Pin

Bail Pin NutsGooseneckPackingWear BushingHousing Seal

Spindle NutShield SealBearing Shield

Bearing Retainer WireBearing^Bearing Housing

Housing lock BoltSpindleSpindle Thread Seal

11121

2

1

2

11

11

1 set (4)1111

1632

3

1 (2)

281/4<2)

V2

3/e(2)3VZ

'/4

%

Ve7V2 (3)

161/4

15

822

1

1 set

2

Parts List for Type 20-XV Swivel20XV-120XV-1E20XV-220XV-11A20XV-420XV-5

20XV-620XV-7

20XV-820XV-920XV-1020XV-1 120XV-1 2

20XV-14

20XV-1520XV-1620XV-17

Bail

ElevatorShanktBail Gudgeon PinBail Pin NutsGooseneckPacking

Wear BushingHousing Seal

Spindle NutShield SealBearing Shield

Bearing Retainer WireBearingt

Bearing Housing

Housing Lock BoltSpindleSpindle Thread Seal

11121

21

21

11

1

1 set (4)1111

21

38

4

1 (2)

43

V4(2)1

V2(2)

4V2

3/B

V2

Ve9% (3)

28

V4

28

822

1

1 set

2

Parts List for Type 25-XV Swivel (For Parts Only)

PartNumber

20XV-120XV-1E20XV-2

20XV-320XV-4

20XV-520XV-620XV-7

20XV-8

20XV-920XV-1020XV-1 120XV-1225XV-1450XV-1525XV-16

20XV-17

Nam of Part

Bail


Bail Pin NutsGooseneck

PackingWear Bushing

Housing Seal

Spindle NutShield SealBearing ShieldBearing Retainer WireBearing^Bearing HousingHousing lock Bolt and Nut


NumberRequired

111

21

21

2

11

1

1

1 set (5)1111

Net WeightPounds

21

38

4

1 (2)43

1A(2)1

V2(2)4V2

V2

1/2

Vn16331

32

Ve

Spares forOne Year

822

1 set

2

Parts List for Type 30-XV Swivel30XV-130XV-1 E30XV-230XV-2A30XV-4

30XV-530XV-630XV-7

30XV-830XV-930XV-1030XV-1130XV-1230XV-14

30XV-1530XV-1630XV-17

Bail


Bail Pin NutsGooseneckPackingWear BushingHousing Seal

Spindle NutShield SealBearing ShieldBearing Retainer Wire

Bearing^Bearing HousingHousing lock Bolt


11121

2

1

2

11

11

1 set (4)1111

26

71

6V2

1 (2)

561/4<2)

2

'/2 (2)

6V2

3/4

Ve

24

42

V4

37

822

1

1 set

2

t When ordering elevator shank, state size of elevator.t Downthrust Bearings, when being renewed, should be replaced with full matched sets.

Never renew one or two bearings in an old set

Type XV Swivels Weight and Dimensional Data

Type Swivel10-XV15-XV20-XV30-XV

Weight

Pounds*

40

95155205

Length

Overall

21"32"34"39"

Working

Length

17"27"29"33"

Lower Conn., Drill

Pipe Thread, L-H.2%" O.D., 8-V2%" O.D., 8-V3V O.D., 8-V4V4"O.a, 8-V

HoseConnection

Vh" NPT2' NPT2V4" NPT3" NPT

Diameter

WatercourseГ/г"

2"

2Уг"

3"

"Sail

Opening2V4" x 23«"

3%" x 8"

41/4" x 8"

5" x 8" or 6" x 14"

• Swivels, boxed for export, weigh approximately: 10-XV, 70 Ibs.; 15-XV, 140 Ibs.; 20-XV, 200 IDS.; 30-XV, 260 Ibs.


Type Swivel

io-xv15-XV20-XV

30-XV


15,00027,00036,000

50,000


30,000

50,00070,000

90,000

2W 6.65 Lb.

1,5002,7003,600

5,000

Safe Depth (Feet) With Drill Pipe2%' 10.4 Lb.

1.8002,400

3,300

•}№ 13.3 Lb.

1,800

2,600

4W 16.6 Lb.

2.100

13

KING OIL TOOLS

10-pXV, 15-PXV, 20-PXV, 25-PXV and 30-PXV SwivelsК

(Illustrations represents one possibleconfiguration. The swivel can beequipped with trunion pins to fit rigrequirements)

For Rigs Equipped with Mechanical PulldownThe bearings are angular-contact type ball bearings. Weight of the drill pipe (downthrust)is carried on a duplex unit. The two bearings in this unit are flush ground, on the faces,and matched so that each bearing will support its share of the load.

Reverse loads (upthrust) are absorbed by double bearings that are mounted opposedto the downthrust unit.

The type of bearings and the manner in which they are mounted provide ample radialcapacity to stabilize the swivels.

The packing unit consists of two molded, composition rubber rings. An extremely hardwear ring (wear bushing) is placed between the two rubber rings. These rubber rings andthe wear bushing replace the washpipes and stuffing boxes that are used in conventionalswivels.

These swivels can be repacked, within a very few minutes, without 'breaking out' anyconnections. Adjustment of the packing is not required and no means of adjustment isprovided.

THE 10-PXV SWIVEL is applicable to small water well, geophysical and core drilling rigs.THE 15-PXV SWIVEL is suited to medium size water well, geophysical and core drilling

rigs.THE 20-PXV SWIVEL operates efficiently on medium large water well, large core drilling

and geophysical drilling rigs.THE 30-PXV SWIVEL is ideal for large water well rigs, and is extremely useful when

reaming down for pit and underreaming, prior to graveling operations. Centrifugal pumpsare frequently used for circulating through this swivel.

This swivel is not recommended for high speed rotation, because the large diameterpacking may fail, due to generation of frictional heat.

Features in Brief• ALLOY STEELS assure strength with minimum weight.• OVERSIZE WATERCOURSES permit circulation of more drilling fluids.• MOLDED RUBBER COMPOSITION PACKING eliminates the usual stuffing boxes.• HARDENED WEAR BUSHINGS eliminate conventional washpipes.• PACKING AND WEAR BUSHINGS are quickly renewable.• MULTIPLE BALL BEARING UNITS provide ample thrust and radial capacities.• SEALED HOUSINGS protect the bearings and retain lubricant.• GREASE LUBRICATION OF THE BEARINGS is accomplished through a readily accessi-

ble fitting,

Instructions for LubricatingThere is a grease fitting set in a recess, near the bottom of the bearing housing. This fittingis to lubricate the bearings.

Use only a good grade of neutral mineral grease that is free of all substances such asgraphite or mica. Either soda soap base or lime soap base greases are satisfactory.

Lubricate every two to three hundred hours of operation. If too much grease is used, theexcess will squeeze out past the upper housing seal.

A slight amount of grease may be thrown from the swivel when new, and after each timeit is lubricated. This is of no consequence.

Pulldown YokesYokes are made of steel. The ends are left unfinished unless the customer can furnishsufficient information to enable us to make the yoke to fit the mast.


TypeSwivel

15-PXV

20-PXV

30-PXV

WeightPounds*

95125185

LengthOverall

29"31"35"

WorkingLength

24"26"30"

Lower Conn., DrillPipe Thread, L.H.

27/e"O.D., 8-V

3V4"O.D., 8-V4'/2" O.D., 8-V

HoseConnection

2" NPT

2V6" NPT

3" NPT

DiameterWatercourse

2"2V4"

3"

Capacities and Safety Data

TypeSwivel

15-PXV

20-PXV

30-PXV

Capacity, Lbs.

at 100 Ft.P.M.

20,000

27,000

32,000

Safe LoadLimit, Lbs.

30,000

40,000

50,000

Safe Depths (Feet) With Drill Pipe2 M" 6.65 Lb.

2,1002,700

3,200

2 7/8" 10.4 Lb.1,3001,8002,400

31/2"1 3.3 Lb.—

1,4002,200

14

KING OIL TOOLS

10-PXV, 15-PXV, 20-PXV, 25-PXV and 30-PXV SwivelsК

Parts List for Type 10-PXV Swivel (For Parts Only)

PXV-4

XV-14XV-16

Parts List for Type 30-PXV Swivel

PartNumber30PXV-232GA-11A30PXV-430XV-530XV-630XV-730XV-830XV-930XV-1030XV-1!30XV-1230XV-1450KG-1530XV-1650KG-17

Name of Part

Yoke PinYoke Pin NutGooseneckPackingWear BushingHousing SealSpindle NutShield SealBearing ShieldBearing Retainer WireBearingtBearing HousingHouse Lock Bolt and NutSpindleSpindle Thread Seal

NumberRequired

12

1

21

2

1

11

1

4

111

1

Net WeightPounds

51V2(2)

531/4

2

V2(2)6

V2

3/4

Ve16

42

V2

37

Ve


8

22

1 set

2

PartNumber

10PXV-210PXV-2A10XV-510XV-610XV-710XV-81 0XV-910XV-1010XV-1110XV-1210XV-1410XV-1510XV-1610XV-17

Name of Part

Yoke PinYoke Pin NutPackingWear BushingHousing SealSpindle NutShield SealBearing ShieldBearing Retainer WireBearing!Bearing HousingHouse Lock BoltSpindleSpindle Thread Seal

NumberRequired

1

2

21

21

1

11

41

1

11

Net WeightPounds

1

'/2 (2)

'/8 (2)

'Л</4 (2)

2

V8

v<Vie6

9V2

Ve7


8

2

2

1

4

2



15PXV-215 PXV-2A15PXV-415XV-515XV-615XV-715XV-815XV-915XV-1015XV4115XV-1215XV-1450KG-1515XV-1615XV-17

Yoke PinYoke Pin NutGooseneckPackingWear BushingHousing SealSpindle NutShield SealBearing ShieldBearing Retainer WireBearing!Bearing HousingHouse Lock BoltSpindleSpindle Thread Seal

12121

211

11

4

11

11

1

1 (2)

24

'/4 (2)3/i

% (2)3V2

'/4

3/8

VB

10

161/4

15

8

2

2

1

4

2

20PXV-220PXV-2A20PXV-420XV-520XV-620XV-720XV-820XV-920XV-1020XV-1120XV-1225XV-1450KG-1520XV-1620XV-17

Yoke PinYoke Pin NutGooseneckPackingWear BushingHousing SealSpindle NutShield SealBearing ShieldBearing Retainer WireBearingtBearing HousingHouse Lock BoltSpindleSpindle Thread Seal

12

1

2

1

21

1

11

41

11

1

3

V2 (2)38

1/4(2)1

3/в (2)41/2

%1/2

Ve1328

'/4

22

8

2

2

1

4

2

Parts List for Type 25-PXV Swivel (For Parts Only)

t When bearings are renewed, replace with a new matched pair. Do not renew one bearingin an old pair. 20PXV, 25PXV and 30 PXV swivels can be furnished with Trunion Pins(similar to KM series) at additional cost.

20PXV-220PXV-2A20PXV-420XV-520XV-620XV-720XV-820XV-920XV-1020XV-1120XV-1225XV-1450KG-1525XV-1620XV-17

Yoke PinYoke Pin NutGooseneckPackingWear BushingHousing SealSpindle NutShield SealBearing ShieldBearing Retainer WireBearingtBearing HousingHouse Lock Bolt and NutSpindleSpindie Thread Seal

1

21

21

2

11

11

51

11

1

31/2 (2)

42

V«(2)

1

%(2)4V2

3/eV2

Va20

331

32

V8

8

2

2

5

2

15

KING OIL TOOLS К25 HPA Swivel with Adjustable Packing r

25HPA Features• (4)- 2"0 Trunniun Pins

• 2 3/a"0 Water Course• Lower Connection Per Customer Order

• 1500 P.S.I. Working Pressure

25HPA Options• 7 V2" Shoulder to Shoulder (I.R.)• 8 5/ie" Shoulder to Shoulder (Failing)

• With or without bail

• Gooseneck Options

• Straight Up

• 90° Out• 30° Down

25HPA Swivelltem#

1234567

89

1011121314151617

1819202122

DescriptionGooseneckGooseneck ScrewsBonnetSpindle (5 Brg.)Packing BoxPkg. Box Set ScrewsWash PipeUpper Housing SealPacking AdapterHousing SealShield SealBearing ShieldBRG Retaining WireBearingSpindle Thread SealO-Ring (Wear Bushing)Bearing HousingPacking Seat RingLantern RingPacking SetO-Ring (Packing Gland)Pkg. Adjusting Nut

Part No.25HPA-0225HPA-02A25HPA-0425HPA-16JE-LHP25HPA-1825HPA-18A25HPA-2525HPA-0720HPA-1320XV-0720XV-0920XV-1 020XV-1 120XV-1 220XV-1725WG-23325PXV-14ETWS75WP-16A75WP-16E75WP-1575WP-34225HPA-20

16

KING OIL TOOLS

20 XVA Swivel with Adjustable Packing

SET SCRfW

20XVA Swivel

25 XVA Swivel with Adjustable Packing

25XVA Swivel

КItem*

123456789101112131415

DescriptionAdjustable GooseneckPacking RingsWear BushingHousing SealSpindle NutSeal ShieldBearing ShieldBrg. Retaining WireBearingBearing HousingSpindle (3.5 IF, LH Pin)Spindle Thread SealPacking Adjusting GlandPkg. Adjusting NutDowell Pin for 20TXV

Part No.20TXV-0420XV-0520XV-0620XV-0720XV-0820XV-0920XV-1020XV-1 120XV-1225PXV-14ETWS20XV-16JE-LHP20XV-1720TXV-1925HPA-20M-074

Item*123456789101112131415

DescriptionAdjustable GooseneckPacking RingsWear BushingHousing SealSpindle NutSeal ShieldBearing ShieldBrg. Retaining WireBearingBearing HousingSpindle (3.5 IF, LH Pin)Spindle Thread SealPacking Adjusting GlandPkg. Adjusting NutDowell Pin for 20TXV

Part No.20TXV-0420XV-0520XV-0620XV-0720XV-0820XV-0920XV-1020XV-1120XV-1225PXV-14ETWS20XV-16JE-LHP20XV-1720TXV-1925HPA-20M-074

17

KING OIL TOOLSК2-KM, 10-KM and 15-KM Swivels

Parts List for Type 10-KM SwivelPart

Number10KM-110KM-210KM-2A10KM-4

10KM-510KM-615XV-7

10KM-815XV-9

15XV-1015XV-1210KM-14

10KM-1510KM-1615XV-17

Name of Part

Bail (Furnished to Order Only)Wear Bushing RetainerWear Bushing Retainer ScrewGooseneckPacking


Bearing SpindleShield Seal

Bearing Shield

Bearings*Bearing Housing

Bonnet Studs and NutsLower Connection

Spindle Thread Seal

No.Req'd

—141

2

1

21

1

1

4

1

4 ea.11

Net WeightPounds

—3

Vie (2)30

1/4 (2)1

% (2)10Yj

1/4

1024

3(4)11

—

Spares for1 Yr. Service

—1

——822

—1

—4———1

г

For Drilling Rigs Equipped With Chain or Cable Pull Down MeansThese swivels are intended primarily as replacements on popular

makes of pull-down type rigs.Bails and pull-down yokes are not normally furnished with these

swivels. These parts can usually be removed from the old swivelsand fitted to the KM type.

Bails will be furnished, when required, on receipt of adequatespecifications.

The bearings are angular-contact ball bearings. They aremounted, in multiple units, so as to absorb thrust loads in eitherdirection. They have ample radial capacity to stabilize the swivelsproperly.

The packing unit consists of two molded, composition rubberrings. An extremely hard wearing ring (wear bushing) is interposedbetween the packing rings. These packing elements can berenewed within a very few minutes.

The 2-KM Swivel is for small Geophysical and Water Well rigs.The 10-KM is for medium size Geophysical, Water Well and Core

Drilling rigs.The 15-KM is ideally suited to fairly large Geophysical, Water Well

and Core Drilling rigs.King Swivels are light in weight in comparison to other make

swivels and are made of alloy treated steel.


Swivel

2-KM

10-KM

15-KM

Weight,Pounds

40

70

80

LengthOverall*

15"

18"

191/2'

Lower (Kelly)Connection

L.H. Tool Pin orL.H. Drill Pipe Thread

N-Rod; Mayhew200 or &g O.D.,8-V

2%"API Reg.;Mayhew 1,000or 2%' D, 8-V

27/8"O.D., 8-V,Drill Pipe

HoseConnection

1 Vf NPT

1 Vf NPT

2" NPT

Diam.Water

Course

ik?"

1'/2"

2"

*Length does not include Bail.

Capacities and Safety Data

Swivel

2-KM10-KM15-KM


10,000

18,00027,000


20,000

30,00030.000

Safe Depths (Feet) With Drill Pipe2%' 6.65 Lb.

1,0001,8002,700

2%' 10.4 Lb.

—

1,2001,800

Parts List for Type 2-KM Swivel

Parts List for Type 15-KM Swivel15KM-115KM-2

10KM-2A15KM-415KM-5

15KM-615XV-715KM-815XV-9

15XV-1015XV-1215KM-14

10KM-1515KM-1615XV-17

Bail (Furnished to Order Only)Wear Bushing Retainera

Wear Bushing Retainer ScrewGooseneckPacking


Bearing SpindleShield SealBearing Shield

Bearings*Bearing HousingBonnet Studs and NutsLower Connection

Spindle Thread Seal

11412121

11

51

4 ea.

11

—

3

Vie(2)24

Ve (2)1

1/4 (2)10

Ve1/4

13

29

3 (4 ea.)11

—

————8

2

2

—1

—

5—

—

—1

When bearings are renewed, replace with a new matched set. Do not replace onein an old set. Be sure that bearings have flush ground faces.

PartNumber2KM-12KM-22KM-2A

2KM-4

2KM-52KM-610XV-72KM-810XV-9

10XV-1010XV-122KM-14

2KM-152KM-162KM-17

Name of Part

Bail (Furnished to Order Only)Wear Bushing RetainerWear Bushing Retainer Screww/NutGooseneckPackingWear BushingHousing Seal

Bearing SpindleShield Seal

Bearing ShieldBearings*

Bearing HousingBonnet Studs and NutsLower Connection

Spindle Thread Seal

No.Req'd

—1

21

21

211

1

4

1

4ea.11

Net WeightPounds

—1'/2

Vie (2)16

Ve (2)3/4

'/4 (2)

5

Ve

V4

610

2(4)5

—


—1

_

—8

2

2

—1

—4

—

——1

18

25-WG Swivel

KING OIL TOOLS КCapacity and Safety Data

20-XV-1

25-WG-825-WG-925-WG-1020-XV-1220-XV-13

25-WG-14

20-XV-7

20-XV-1725-WG-16

Swivel

25 WG

CapacityPounds at100 R.P.M.

36,000

StaticLoad

75,000

PulldownCapacity at100 R.P.M.

30,000

Parts List for Type 25-WG SwivelPart

Number

20XV-120-XV-1E20-XV-232-GA-11A25-WG-420-XV-525-WG-620-XV-725-WG-820-XV-920-XV-1020-XV-1225-WG-1420-XV-1620-XV-1725-WG-1825-WG-233

Name of Part

BailElevator ShankBail Gudgeon PinBail Pin NutBodyPackingWear BushingHousing SealSpindleShield SealBearing ShieldBearingBearing HousingLower ConnectionSpindle Thread SealHousing Lock SealWear Bushing "O" Ring

No.Req'd

111212

1

21

1

1

511

11

2

Net WeightPounds

21

38

4

1 (2)

85

'/4 (2)

2

V2 (2)14

%

'/2

1714

1Г/2—1/4

'/4


—————812

—1

—

5

——1

—

2

NOTE: Bearings should be replaced with a matched set.

To Repack Swivel:Screw the three (3) hold screws down until the wear bushing assembly comes together. Remove assembly throughwindow. Remove old packing rings, insert new ones, reinstall bushing and tighten hold screws until proper adjustment isobtained. As packing wears, tighten screws evenly to obtain full life of packing.

15-KF Swivel

Weight And Dimensional Data15-KF-415-KF-1515-KM-515-KM-6

15-KF-25-CRC-15S

15-KM-520-XV-720-XV-915-KF-10

15-KF-1215-KF-1215-KF-13

15-KF-1420-XV-715-KF-815-XV-1715-KF-16

Length,Inches

251/2

Weight,Pounds

114

Lower Connection

2%" API I.F. Tool Joint

HoseConnection

2" NPT

DiameterWatercourse

~


Capacity Los. at 100 RPM

27,000

Static Load LimitsLbs.

31,000

Safe Depths (Feet)With Drill Pipe

2%' 6.65 Lb.

2700

2W 10.4 Lb.

1800

Parts List for 15-KF Swivel

PartNumber

15-KF-25-CRC-15S15-KF-415-KM-515-KM-620-XV-715-KF-820-XV-915-KF-1015-KF-1215-KF-1415-KF-1515-KF-1615-XV-17

Name of Part

Wear Bushing RetainerWear Bushing Retainer ScrewGooseneckPackingWear BushingHousing SealBearing SpindleShield SealBearing ShieldBearingBearing HousingBonnets Studs and NutsLower ConnectionSpindle Thread Seal

No.Req'd

12

1

21

21

1

1

31

41

1

Net WeightPounds

1—32—1

—8

—

V2

18

32

2

16

—

Ozs.

122—2

—

e12

e———2

—

—

The swivel measures 8̂ 16 in. from end to end of the trunion pin, 12-in. diameter on the trunion pin, or to specification.

г in. from the shoulder to the pin end; and it has a

19

KING OIL TOOLSКЗАРЕ Rotating Head

ЗАРЕThe ЗАРЕ rotating head was designed as a rotating head and notas a load carrying swivel. This unit was designed for pressures

exceeding 250 PSI and up to 1500 PSI and is equipped withchevron (V-type) packing and a hardened and ground washpipe.

Two zerk fittings are provided on the 3BL-14 bearing housing forbearing lubrication, and on the APE gooseneck for packing

lubrication. A good grade of molybdenum base grease isrecommended.

ЗАРЕ Rotating Headltem#

123456789

1011121314

DescriptionGooseneckWashpipeStemAdapter PlateBearing (2)Packing Set (4 Rings)O-RingLantern RingStud (10)Set Screw (2)Grease Seal (2)Bearing HousingPacking AdapterSide Connector

Part No.3APE-013APE-253APE-073APE-043BL-1250KG-203BL-34050KG-21B038C350HNNBB025C025XXXS3APE-103APE-052.5BL-06A3APE-01A

ЗАРЕ Rotating Headltem#

123456789

10111213

DescriptionGooseneckWashpipeStemAdapter PlateBearing (2)Packing Set (4 Rings)O-RingLantern RingStud (10)Set Screw (2)Grease Seal (2)Bearing HousingPacking Adapter

Part No.3APE-01-S3APE-253APE-07-07A-LHP3APE-043BL-1250KG-203BL-34050KG-21B038C350HNNBB025C025XXXS3APE-103APE-052.5BL-06A

W/3" N.P.T. THD L.H. PIN f20

KING OIL TOOLS КRotating Heads

^̂

MODEL 2.5 BL

2.5BL-16

For Top-head Drive Drilling RigsThese rotating heads are designed for large volumes of air or fluid needed on Top-headDrive Rigs.

Precision bearings provide ample thrust and radial load capacity and are greaselubricated.

Short, compact design requires a minimum of space.The 2.5-BL Head is designed for high pressure.The 3-BL Head is designed for low pressure.


TypeHead

2.5 BL3 BL

LengthInches

18

18

WeightPounds

70

65

Lower Conn.*Box or Pin

2V2"or3"NPT2V2" or 3" NPT

HoseConn.

2V2"

3"

DiameterWatercourse

2V2" Max.3" Max.

'Lower connection per customer spec., specify RH or LH box or pin.

Parts List 2.5 BL

Parts List 3 BL

PartNumber

2.5-BL-42.5-BL-62.5-BL-6A4-SC-72.5-BL-820-XV-113-BL-123-BL-142.5-BL-163-BL-1750-KG-2050-KG-2150-KG-2575-WP-339

Name of Part

GooseneckPacking NutPacking Seat RingHousing sealSpindieBearing Retainer WireBearingBearing housingLower ConnectionSpindle Thread SealPackingLantern RingWashpipe"O" ring

NumberRequired

111211

21

11

1 set1

11

WeightLbs. Oz.

181

0

0

8

0

6

10

15

001

4

0

0

2

4

4

02

0

0

04

8

0

81

Sparesfor One

Year

——3

2

—1

2

—

—1

61

3

3

PartNumber

3-BL-44-SC-630XV-54-SC-73-BL-820XV-1 13-BL-123^BL-143-BL-163-BL-17

Name of Part

GooseneckWear BushingPackingHousing sealSpindleRetainer WireBearingBearing housingLower ConnectionSpindle Seal

NumberRequired

11221

1

21

1

1

WeightLbs. Oz.

181

0

0

8

0

12

10

15

0

00

4

40

4

0

0

04

Sparesfor One

Year

—14

2

—

—

2

—

—1

MODEL 3 BL

21

KING OIL TOOLS К1-J and 2-J Swivels

J-5

J-6

For Drilling Shot Holes in Marshes and Jungles, for DrillingHousehold Water Wells, for Use on Light Hydraulic Rigs andSmall Jetting RigsThese swivels incorporate materials best suited to the purposes. The parts are finishedwith the same care, and to the same precisionrequirements, as our larger models.

The bearings are duplex, angular-contact type, mounted back to back. They are sealedin the housings, and provision is made for lubricating by means of grease gun.

The housing parts are made of aluminum alloy castings for seismograph rigs, and ofnickel-iron for water well rigs.

The U-bolt bails are made of alloy steel and are heat-treated. Thespindles and lower connections are also high grade steel.

The packing units consist of two molded, composition rubber rings. A hardened wearring (wear bushing) is interposed between the rubber rings.


sb1-J

2-J

Length,inches

13

14

Weight, PoundsAluminum

10

14

Iron

15

21

LowerConn., NPTf

1" ОГ1У4"

1 Vi' or 2"

HoseConnection

1 " female NPT or1 1/4" male NPT1 Vf NPT

DiameterWatercourse

7/8" ОГ 1 W

1У2"

tSpecial connections, at additional cost, furnished on order.

Type J Swivels, Safe Depths at 100 R.P.M.1 -J, safe depth: 500 feet with 1W standard weight pipe.2-J, safe depth: 500 feet with 2" standard weight pipe.

Parts List for Type 1-J Swivel

Number

1J-1A1J-11J-21J-31J-41J-51J-61J-71J-8A1J-81J-9

Name of Part

Gooseneck (Aluminum)Gooseneck (Iron)Bail w/NutsPackingWear BushingBearing SpindleLower ConnectionHousing SealBearing Housing (Aluminum)Bearing Housing (Iron)Bearings

Required

1112

2

2

W

Lbs.

1

41

——

11

—

1

41

tight

Ozs.

9

2

101/4

32

81

8—

11

Spares for

Service

_—61

——2

——2

Parts List for Type 2-J Swivel2J-1A2J-12J-22J-32J-42J-52J-62J-72J-8A2J-82J-9

Gooseneck (Aluminum)Gooseneck (Iron)Bail w/NutsPackingWear BushingBearing SpindleLower ConnectionHousing SealBearing Housing (Aluminum)Bearing Housing (Iron)Bearings

11121112112

2

5

2—

—

2

2_

2

5

2

2

101

'/2

4—

7

1У2

—

84

—

—

—

61_

—

2—

—

2

To Renew Packing: (1) Screw top nuts up one-half inch on bail. (2) Separate gooseneck from housing one-half inch,(3) Remove packings and wear bushing. (4) Insert new packings and wear bushings. (5) Screw nuts back tight.

Ж

22

KING OIL TOOLS К10 JSS and 45 JSS Water Swivels

10JSS-1 Goosenei

10JSS-7

10JSS-5

MODEL 10 JSS

45 JSS-1

45 JSS-345 JSS-445 JSS-3B45 JSS-9A45 JSS-9B10XV-12

45 JSS-7

45 JSS-5

For Core Drilling and High-Speed DrillingThese swivels are designed for high drilling speeds.

The bearings are flush ground, high angular contact, giving exceptional thrust and radialstability. They are sealed in the housing and are grease lubricated.

The packing is non-adjustable, chevron type, selected for high speed applications.


Model

10 JSS45 JSS

LengthInches

123/8

15V4

WeightPounds

2027

LowerConnection

AW

NW

HoseConnection

1"1 1/4"

Watercourse

W1%"

Capacity (Non-Rotating)

10 JSS45 JSS

10,000 Ibs.45,000 Ibs.

Parts List for Type 10 JSS Swivel

Parts List for Type 45 JSS Swivel

PartNumber

10-JSS-110-JSS-2io-jss-310-JSS-3A10-JSS-410-JSS-510-JSS-710-JSS-81-J-910-JSS-9A10-JSS-9B10-JSS-227

Name of Part

GooseneckLock nutPacking setPacking springPacking boxSpindleHousing sealBearing housingBearingBearing lock nutBearing lock washerO-ring

NumberRequired

111111

2

WeLbs.

4

0

0

001

041

0

0

0

ghtOz.

2

8

4

0

8

21

0

11

4

2

0

Spares forOne Year

_—662

1

2_

21

1

6

PartMumbe

45-JSS-145-JSS-245-JSS-345-JSS-3B45-JSS-445-JSS-545-JSS-745-JSS-845-JSS-9A45-JSS-9B10-XV-1225-WG-233

Name of Part

GooseneckLock nutPacking setWear sleevePacking boxSpindleHousing sealBearing HousingBearing lock nutBearing lock washerBearingO-ring

NumberRequired

1

31

WeightLbs. Oz.

200002

—50040

285580

—82620

Spares forOne Year

_—62

21

1—

1

1—

6

MODEL 45 JSS

23

KING OIL TOOLS К4.5-SI Side Inlet Swivel

4.5SI-1

4.5SI-34.5SI-3A

« I« I Ittljt

Call factoryfor Dual TubeApplications

5-EL and 5-PEL* Swivels

5-EL-2

5-EL-1

5-EL-6

These swivels are manufactured of high-grade alloy steel and designed to fill a need whenconventional swivels are not practical or applicable.

Side inlet swivels find a wide application when using hydraulic, top-head drive rigs.Mounted below the hydraulic assembly, they prevent contamination of hydraulic fluidcaused by leakage in conventional swivels.

Auger rigs can be converted to circulating, rotary, drilling rigs.When drilling with large diameter pipe, this swivel can be mounted below the existing

swivel to provide more air or drilling fluid as required.These units are ideal for dual-tube drilling on lost circulation holes.The upper and lower connections can be furnished with pin or box, or flange.

Features in Brief• Alloy steel for maximum strength with minimum weight.• Compact design for use on short mast rigs.• Sealed bearings give ample load capacity.• Adjustable chevron-type packing easily replaceable.


r

LengthInches

22%

WidthInches

81|У16

WeightPounds

230

Connections*

31/» API Reg. RH

WatercourseDiameter

11/2"

HoseConnection

2"

"Consult factory for other connections

Parts List for Type 4.5 Side Inlet Swivel

PartNumber

4.5SI-14.5 SI-34.5 SI-3A4.5 SI-44.5 SI-54.5 SI-5A4.5 SI-64.5 SI-74.5 SI-94.5SI-104.5SI-1110-XVII4.5 SI-264.5 SI-33A

Name of Part

Spindle StemLower Adjusting GlandLower Adjusting Gland RingPackoff HousingPacking SetLantern RingUpper Adjusting NutLower Grease SealBearing HousingUpper Housing SealBearing Housing CapBearing Retainer WireBearingBearing Spacer

No.Required

11112211111121

WeightPounds

11041

45'/2У241

2015

—10

1

Spares forOne Year

2

84

2

1

: 1

21

For Drilling Shallow to Medium Depth Water Wells and for Use on Light to MediumHydraulic Rigs.For deeper wells and heavier load capacities that can not be accomodated by the King2-J Swivel.

The bearings are duplex, angular-contact type, mounted back to back. They are sealedin the housings which are designed to permit lubrication with grease gun.

Gooseneck and bearing housings are made of alloy steel, heat-treated.U-bolt bails are made of alloy steel, heat-treated. Spindles and lower connections are

also of high grade steel.Packing consists of two molded, composition rubber rings. A hardened wear ring (wear

bushing) is interposed between the rubber rings.*Note: Type 5-PEL (not shown) is similar in construction to the 5-EL except for its gooseneck, which is similar to the PXV.


LengthInches

16'/4"

weightPounds

35

Lower Connection,HPT

2" LH or RH

HoseConnection

2" NPT

DiameterWatercourse

2"

Parts List for Type 5-EL SwivelPart

Number

5-EL-15-EL-25-EL-35-EL-45-EL-55-EL-65-EL-75-EL-85-EL-95-EL-175-PEL-1

Name of PartGooseneckBail w/NutsPackingWear BushingSpindleLower ConnectionHousing SealBearing HousingBearingsSpindle Thread SealGooseneck

NumberRequired

11211121211

Lbs.

105

24

83

11

Ozs.

124

48

2

I82

12

-«•

Type 5-EL Swivels, Safe Depths at 100 RPM2500 feet with 41/2" Standard Weight Pipe1500 feet with 2" Standard Weight Pipe

24

KING OIL TOOLS КSide-Inlet Swivels

Stem

Retainer Ring

Bearing

Retainer Ring

Packing

Packing Set Ring

Packotf Box

HAW/HNW SWIVEL

IF-DC SWIVEL

Stem

Retainer Ring

Bearing

Retainer Ring

Packing

Packing Set Ring

Packoff Box

Drive Adapter

Manufactured of high-grade alloy steel, these swivels fill the needwhen conventional swivels cannot be used.

These side-feed swivels feature grease-lubricated, pressure-energized, non-adjustable chevron (V-type) packing and upper andlower ball bearings for radial loads. They are suitable for air ormud drilling.

Although designed for many hours of drilling, these swivels can beeasily repacked in the field for extended service.


HAW

HNW

Length

13-1/2"

14-1/16"

Width

4"

5"

Weight

22#

35#

UpperConnection

1-5/8" HEX

1-5/8" or 2" HEX

LowerConnection

AW BOX

NWBOX

Water-course

5/8"

1-3/8"

HoseConnection

1" NPT

1-1/4" NPT

Parts List

HAW HNW

Part No.

HAW 1-01

HAW 1-04

HAW 1 -06

HAW 1-26

HAW 1-325

HAW 1-354

Name

Stem, AW RH Box

Packoff Housing

Packing Set

Bearings

Packing Retainer

Bearing Retainer

Requires

112

2

2

2

Part No.

HNW-01

HNW-04

HNW-05

75WP-16A

HNW-26

HNW-400W

HNW-433W

Name

Stem, NW RH Box

Packoff Housing

Packing Set

Packing Seat Ring

Bearings

Packing Retainer

Bearing Retainer

Requires

112

2

2

г2

The IF-DC Swivel is designed for wet augering or grouting withoutmoving the rig.

A semi-finished, bolt-on adapter accepts drive caps 41/4" through 6Уг".


IF-DC

Length

20-7/8"

Width

7-1/2"

Weight

85#

UpperConnection

2" HEX

LowerConnection

2-3/8" IFRHP

Water-course

1-3/8"

HoseConnection

1-1 /2" NPT

Parts Lists

Part No.

IF-DC 01 FE

NWDC-04

NWDC-05

HNW-26

Name

Stem, 2-3/8 IF RH Pin

Packoff Housing

Packing Set

Bearings

Requires

1

1

2

2

Part No.

NWDC-275W

NWDC-375W

IFDC-45

10MB-347

Name

Bearing Retainer

Packing Retainer

Drive Cap Adapter

O-Rrng Adapter

Requires

1

1

1

1

25

6-CRC Swivel

KING OIL TOOLSкFor Drilling Irrigation Holes and Pile Driving Operations, Either Conventional orReverse Circulation.

Features in Brief• FLEXIBLE BAIL.• 6" WATERCOURSE.• CHEVRON PACKING ASSEMBLY permits easy field replacement and adjustment.• LOWER ALIGNMENT BEARING.• 2" COUPLING ON TOP OF GOOSENECK.• SHORT, COMPACT, ALLOY STEEL CONSTRUCTION.• EXTENDED BAIL PINS serve as guides.


Type Swivel

6-CRC

Wblght

775 Ibs.

Length Hose Connection

6" NPT

Lower Connection

61/2" mod. LHtool joint*

•With beveled sub for welding to Kelly.


Capacity at 100 RPM

35.000 Ibs

Static Load Limit

100,000 Ibs,

6-CRC Parts List

PartNumber

6-CRC-16-CRC-26-CRC-36-CRC-46-CRC-56-CRC-66-CRC-76-CRC-86-CRC-126-CRC-166-CRC-206-CRC-216-CRC-226-CRC-236-CRC-245-XLW-156-CRC-266-CRC-276-CRC-286-CRC-296-CRC-306-CRC-316-CRC-2656-CRC-366-CRC-376-CRC-386-CRC-396-CRC-406-CRC-2596-CRC-2646-CRC-2756-CRC-2786-CRC-442

Name of Part

BailBail PinBail Bolt with nutsGooseneckPackingPacking BoxOil SealSpindle StemUpper HousingLower HousingGooseneck ScrewsUpper BearingBearing SpacerShim SetMain BearingAlignment BearingOil Seal BoxOil Box ScrewsLower Oil SealAdapter SubSeal Wear RingBearing Hold Down Nut"O" Ring Packing BoxPacking GlandLantern RingAdjusting GlandPacking Seat RingWashpipe"O" Ring Washpipe"O" Ring Spindle"O" Ring Oil Box"0" Ring Housing"O" Ring Gooseneck to Bonnet

No.Req'd.

1221

1 set12111811

1

11

1

811

1

111

1

111

1

1

21

11

Req'd.Spares

for 1 Year

612

1

1

1

1

11

1

1

21

Repacking Instructions: Loosen the four gooseneck hold-down screws in the Packing Box. Insert spanner wrench onwashpipe by rotating spindle stem to right. Remove packing assembly, thru window, and replace spent packing "O"rings and washpipe if necessary. Install assembly in gooseneck window and tighten washpipe by using spanner wrenchand rotating spindle to left. Tighten gooseneck screws on packing box and continue drilling.

26

5-KCOS Swivel

KING OIL TOOLSк

5KCOS-395KCOS-375KCOS-55KCOS-65KCOS-365KCOS-2635KCOS-205KCOS-16

For Drilling Shallow to Medium Depth Water Wells and for Use on Light to MediumHydraulic Rigs. For Conventional or Reverse Circulation; also for Pile-DrivingOperations.The King 5-KCOS is a husky, compact swivel with an unrestricted fluid passage 5 inchesin diameter for extra circulation.

Bearings are two-row tapered roller type with more than ample thrust and radialcapacity. Bearings are protected by automatic seals which retain the lubricant andexclude abrasive substances.

The packing unit consists of chevron type rings and washpipe. The packing unit can berenewed, in a very few minutes, without breaking out any of the swivel connections.

The hose connection is 5-inch National Pipe Thread, furnished straight out or at a down-ward angle — 90° to right or left — as specified. The Kelly connection (bottom thread) isnormally 6-inch National Pipe Thread, left hand. Other threading furnished on order.

Housing parts are flanged and bolted together with 12 one-inch bolts.The bail has a stop to limit its swing to approximately 60° from its normal position.


Type Swivel

5 CRC-- with 6% O.D. NP.T. L.H.

WeightPounds

512

LengthInches

41

WorkingLength

34"

WaterCourse

5"

BallOpening

6" x 8"

Hose Connection: 5" NPTLower Connection: 6" NPT Left Hand Pin


Capacity Lbs. at 70 rpm

35,000

Static Load Limit Lbs.

150,000

Safe Depth with Drill Pipe

6%— 25.20* 1500'

5-KCOS Parts List

PartNumber

5CRC-153GA-1253GA-1 15CRC-45KCOS-55KCOS-65CRC-75CRC-85CRC-95KCOS-105KCOS-1 15CRC-125KCOS-135KCOS-165KCOS-4345KCOS-205KCOS-285KCOS-365KCOS-375KCOS-385KCOS-395KCOS-405KCOS-2525KCOS-2635CRC-449

Name of Part

BailBail PinBail Pin NutGooseneckPackingPacking BoxUpper Housing SealFelt WasherBearing AssemblyHousing StudStud NutBearing HousingSpindle NutLower HousingSpindle Thread SealGooseneck ScrewsLower Housing SealPacking GlandLantern RingAdjusting GlandPacking Seat RingWashpipe"O" Ring (Washpipe)"O" Ring (Packing Box)"O" Ring (Housing)

No.Required

112111111881111

611211111

WeightPounds

4710%

951

17УвУв

6411

8920

187Ув1/4

Ув2261

10'/16VieVie

Req.Spares forOne Year

6222

1

23111

. 3331

27

KING OIL TOOLS

4W Swivel Assembly

3MB-1

4W-01ES ELEVATOR SHANK

К

6 5/8 API REGLEFT HAND

4W SwivelItem*

12345678910111213141516171819

DescriptionGooseneckPacking Seat RingO-Ring (2)O-RingO-RingGlandPacking SetLantern RingStuffing BoxBearing (set of 5)Bearing HousingWash pipeUpper SealBonnetBearing ShieldLower HousingO-Ring Spindle Thread SealLower ConnectionBail

Part No.4W-014RC-114RC-2504RC-2544RC-2444RC-094RC-8-4164RC-104RC-054WP-074W-144RC-074BL-074W-044W-10 •4RC-17 |4RC-34B4W-163MB-01

28

KING OIL TOOLS К15-PS Power Swivels

Features:Compact Dependable Alloy SteelMaximum working pressure is insured by multi-ring, pressure sealing, v-type, adjustablepacking

Interior design provides all bearings and gears with a flood of oil.Spherical roller, main bearings, and radial lower bearing gives stability and durability.Rotating parts are driven by a high pressure, dependable, gear-type motor through a

single reduction spur gear pinion.Two extensions of the bail pins are provided for torque arms.Ease of maintenance designed into swivel and drive, no special tools are required.

Swivel SpecificationsStatic Hook CapacityDynamic CapacitySpindle Connection*Spindle BoreGooseneck ConnectionMaximum Working PressureWashpipe Packing

LubricationFluid Motor

Torque ArmsGear RatioSpur Gear PinionsHydraulic Connectors

1 30 [email protected]/2" API Reg. (R.H.) Pin25/s" I.D.3"A.P.I, Line Pipe Box5000 P.S.I.Floating type Multi-Ring, Pressure Sealing Typewith provision for Gland AdjustmentOil BathTwo gear Type, 3000/5000 P.S.I. continuous workingpressureExtension of Bail Pins or Bolted on Type.Single Reduction of 4.31 1 with Dual

Quick Disconnects"Other tool joints can be furnished per customer's request.

Hydraulic SpecificationsRated Continous Flow & Pressure 90 G.P.M. @ 3000 P.S.I. or 45 G.P.M. @ 5000 P.S.I.Maximum Speed 160R.P.M.Maximum Torque 10,790ft. Ibs.

29 i

KING OIL TOOLS К3-PS King Swivel

MODEL 3PS

Features:Compact Dependable Alloy SteelMaximum working pressure is insured by multi-ring, pressure sealing, v-type, adjustablepacking.

Interior design provides all bearings and gears with a flood of oil.Spherical roller, main bearings, and radial lower bearing gives stability and durability.Rotating parts are driven by a high pressure, dependable, gear-type motor through a

single reduction spur gear pinion.Two extensions of the bail pins are provided for torque arms.Ease of maintenance designed into swivel and drive, no special tools are required.

SpecificationsStatic Hook Load

Dynamic Hook Load

Spindle Connection*

Spindle Bore

Gooseneck Connection

Maximum Working Pressure

Washpipe Packing

Lubrication

Fluid Motor

Torque Arms

Gear Ratio

Hydraulic Connections

85 Tons

55 Tons @ 100 R.P.M.

ЗУг A.P.I. I.F. (R.H.) pin

2%" I.D.

3" A.P.I. Line Pipe Box

3000 P.S.I.

Multi-Ring, Pressure Sealing Type withprovisions for packing gland adjustment

Oil Bath

One gear Type, 3000 P.S.l. continuous workingpressure, 10% intermittent duty pressure to 3500P.S.I. Two Speed Motor

Two-Extension of bail pins

Single Reduction of 3.62:1 with singlespur gear pinion

Pressure Port 1 5/16 12 UNC-3B Str. Thd."O" Ring Boss.Drain Port (Req'd. only when back pressureexceeds 1000 psi'/8-14 UNF "O" Ring Boss

•Other Tool Joints can be furnished per customer's request.

PerformanceRated Continuous Flow & Pressure 45 GPM @ 3000 PSI

Maximum Speed @ Rated Flow & Pressure to 190RPMMaximum Torque @ Rated Flow & Pressure 5,249 Ft. Ibs.

f

30

7.5-LW Swivel

KING OIL TOOLSкHeavy-Duty, Large-Watercourse Swivels designed for Big-Hole MineDrilling, for Deepest of Water WellsThe type LW Swivels are of rugged construction. They are made with the largest water-courses in the King line, built tor highly efficient operation in drilling large irrigation waterwells and large holes for the mining industry, and for offshore piling operations and eleva-tor shafts.

Features in Brief• ALLOY STEELS assure strength with minimum weight.• OVERSIZE WATERCOURSE permits circulation of more drilling fluids.• OIL BATH LUBRICATION assures longer, trouble-free service.• CHEVRON-TYPE PACKING — washpipe packing is easily renewed without breaking out

gooseneck.• COMPACT — fits standard rigs.

Available with top hanger for hanging inner tube for dual purpose drilling.

Specifications for the King 7.5 LW Series Swivel

ModelStatic LoadBearing Capacity At 20 RPMRadius of Bail at Hook* Hook ClearanceMinimum Fluid PassageHose Connection — Line PipeLower PinWashpipe PackingUpper BearingCenter BearingLower BearingLubricationWidth At TrunionsLength Overall Less Sub

7.5 LW400,000300,000

43/4"

15"7.5"

8" x150# Flange7.5" Modified L.H.

Vee ChevronTapered Roller

Spherical Roller ThrustStraight Roller

Oil Bath30"7'6"

* This clearance may be varied per customer specifications.

31

KING OIL TOOLSк4-SC, 5-SC, and 7-SC Circulating Heads

5SC-4

5SC-8SSC-14

i

Model 7SC

For Wire Line Coring, Sldewall Coring, Sampling, Well LoggingThese units have ample thrust and radial bearing capacities to withstand continuousrotation over long periods of time. Bearings are grease lubricated and enclosed in an alloysteel housing. A short, compact design requires a minimum of space.

ConnectionsLower Connection: 4'/2" API IF RH PIN*Upper Connection: 4" FEMALE LINE PIPE*Hose Connection: 3" FEMALE LINE PIPE**Other connections available at customer request

Weights and Dimensions

Model

4SC

5SC

7SC

OverallLength

253/4"

34"

40"

FluidPassage

3"

3"

23/«"

WorkingPressure

3000 PSI

6000 PSI

10,000 PSI

WeightPounds

175

185

460

ExportWeight

23Q

245

500

Parts List 4SC

Parts List 5SC

Parts List 7SC

Part No.

4SC-4

30XV-5

4SC-6

4SC-7

4SC-8

4SC-9

4SC-10

4SC-12

4SC-14

50KG-15

4SC-16

50KG-17

Name of Part

Body

Packing

Wear Bushing

Housing Seal

Bearing Spindle

Felt Seal

Bearing Shield

Bearings

Bearing Housing

Housing Lock Bolt

Lower Connection

Spindle thread Seal

NumberRequired

12

1

2

1

1

1

4

1

1

1

1

WeightPounds

701/4 (2)

11/2 (2)

181/41/2

4

181/2

501/4

Spares forOne Year

—4

1

2—

1—

4—

—

—

1

Part No.

5SC-12.5 BL-62.5 BL-6A

4SC-7

5SC-830XV-9

30XV-1030XV-12

5SC-14

50KG-15

5SC-16

50KG-17

50KG-20

50KG-21

50KG-25

75WP-339

Name of Part

BodyPacking NutPacking Seat Ring

Housing SealBearing SpindleShield Seal

Bearing ShieldBearings

Bearing Housing

Housing Lock Bolt

Lower Connection

Spindle thread Seal

Packing

Lantern Ring

Washpipe

O-Ring

NumberRequired

111211141

1

1

1

1

1

1

1

WeightPounds

75

41/81/2 (2)

221/23/4

4

451/4

501/41/2

1

41/2

—

Spares forOne Year

_—2

2—

1—

4—

—_

1

2

1

2

2

Part No.

7SC-04

2.5 BL-62.5 BL-6A

4SC-7

5SC-8

30XV-9

30XV-10

30XV-12

5SC-14

50KG-15

5SC-16

50KG-17

50KG-20

50KG-21

50KG-25

75WP-339

Name of Part

Body

Packing Nut

Packing Seat Ring

Housing Seal

Bearing Spindle

Shield Seal

Bearing Shield

Downthrust Bearing

Bearing Housing

Housing Lock Bolt

Lower Connection

Spindle thread Seal

Packing

Lantern Ring

Washpipe

O-Ring

NumberRequired

1112

1

1

1

4

1

1

1

1

1

1

1

1

WeightPounds

75

4

Ve1/2 (2)

221/23/4

4

451/4

501/41/2

1

41/2

—

Spares forOne Year

——22—

1—

4—

—_

1

2

1

2

2

32

KING OIL TOOLS КAR (Auto-Releasing) Wire Line Strippers 3-AR and 4-AR

For Swabbing Tubing-Wire Line Coring-Sidewall Sampling-Well LoggingA safe, efficient and economical tool for keeping the derrick floor clean and dry whileswabbing or pulling wire line cores and for other operations where a wire line is being runin and out of a well.

THE 3-AR STRIPPER IS USED MAINLY FOR SWABBING TUBING.THE 4-AR STRIPPER IS USED PRINCIPALLY IN CONNECTION WITH WIRE LINE

CORING OPERATIONS.These Wire Line Strippers represent an outstanding advance in design and construction

in tools of this class. They present to the oil industry many advantages that were notpreviously available. (Strippers are sometimes referred to as "wipers" or "oil savers.")

Features in Brief• A POSITIVE LATCH ARRANGEMENT will not release by accident or a surge of pressurein the well. • A SURE RELEASE MECHANISM ... operated by the rope socket striking thebottom of the stripper. • A RUBBER SHOCK ABSORBER to cushion the blow of the ropesocket when the stripper is released. • NON-SPARKING MATERIALS minimize1 the firehazard. • ROLLER WIRE LINE GUIDES on hardened steel pins, with Alemite greasenipples. • SIDE OPENINGS for inserting the wire line packing rubbers. This is an aid torepacking and permits repacking when the line is in the hole. • THE PACKING ISSELF-CENTERING and does not require the compression screws to be evenly adjusted.• THE COMPRESSION SCREWS may be unscrewed enough to relax the packing, if nofluid or pressure is present, while the line is being run. This method will minimize upkeepand conserve rubber. At no time should the screws be tightened unduly. • A SELF-SEALING PACKING RING seals between the stripper and latch collar. A cushion of rubberis provided to seat on the latch collar. • CONVENIENT HAND HOLDS are an aid to easyhandling.

General Data 3-AR and 4-AR Wire Line Strippers

Striper

3AR

4AR

OverallLength

17V/

181/4"

Max. SizeWire Line

WW

Inside Dlam.Max. Bore)

3"

35V

WeightPounds

43

54

CollarThread

(Line Pipe)

3" Male4" Male

Length AboveCollar Thread

141/2"

141/2"

Parts List for Type 3-AR Wire Line Stripper Parts List for Type 4-AR Wire Line Stripper

PartNumber

3AR

3AR-14AR-14AR-2V4AR-33AR-43AR-53AR-63AR-74AR-83AR-93AR-104AR-114AR-11T

4AR-123AR-133AR-144AR,154AR-164AR-17

Name of Part

Wire Line Stripper, completeBodyYokeVise Type ScrewStripper Rubber HoldersLatch Dog^MandrelLatch CollarLatch DogsLatch CageStripper RubbersfCushion RubberLatch Collar Seal RingLine Wear BushingWear Bushing Threaded forTrip Bar— 11/2"NPTPacking Retainer PinsLatch Dog SpringsLatch Cage SpringLine Guide RollersRoller PinsRoller Pin Bushings

NumberRequired

11121

1

41

1 set (2)111

1241

2

2

2

New WeightPounds

43*

11%61/4

7/8

3% (2)

31/4

9%

1 1/8 (4)2%

%

%1/4

%

21/4

'/8 (2)1/16

Vfe

17/8(2)7/8 (2)%(2)


4

20 sets12

3

2

24

1

4

2

2

PartNumber

4AR

4AR-14AR-24AR-2V4AR-34AR-44AR-54AR-64AR-74AR-84AR-94AR-104AR-114AR-11T

4AR-124AR-134AR-144AR-154AR-164AR-17

Name of Part

Wire Line Stripper,, completeBodyYokeVise Type ScrewStripper Rubber HoldersLatch Dog MandrelLatch CollarLatch DogsLatch CageStripper RubberstCushion RubberLatch Collar Seal RingLine Wear BushingWear Bushing Threaded forTrip Bar— 1 Vf NPTPacking Retainer PinsLatch Dog SpringsLatch Cage SpringLine Guide RollersRoller PinsRoller Pin Bushings

NumberRequired

1

121

1

41

1 set (2)111

1241

2

2

2

New WeightPounds

52"

13%

7/8

3% (2)4

131/2

1%(4)

3%

%%1/4

%

1%

V8(2)

VB (4)

Vt17/a(2)

7/8(2)

Щ2)

Snares forOne YearService

4

20 sets12

3

2241

4

2

2

Note: Parts having 4-AR numbers interchange on 3-AR and 4-AR Strippers. "Strippers complete, boxed for export, weigh approximately: 3-AR 75 pounds — 4-AR 85pounds.

tWhen ordering stripper rubbers, specify size of line to be used.

33

KING OIL TOOLS

Center Latch Collar Type Tubing Elevators

К

Safety Double Lock OperationEach Half Balanced for HandlingRear Third HandleCertified Load TestInterchangeable Parts DesignRegular or Arctic Service

SPECIFICATIONS

Capacity

API Range

Weight

TA-K-32387

35 Tons

(32 Tonne)1.050" thru

2-7/8"54#

TA-K-32385

65 Tons(59 Tonne)1.660" thru

2-7/8"64#

TA-K-32386

65 Tons(59 Tonne)3-1/2" thru

4-1/2"83#

TA-K-32383

100 Tons(91 Tonne)2-3/8" thru

2-7/8"100#

TA-K-32384

100 Tons

(91 Tonne)3-1/2" thru

4-1/2"158#

RA-K-25462

125 Tons

(113 Tonne)2-3/8" thru

3-1/2"162#

f34

KING OIL TOOLSI

Single Joint ElevatorsК

tCenter Latch OperationFive Ton CapacityCertified Load TestInterchangeable Parts DesignRegular or Arctic Service

SPECIFICATIONS

Capacity

API Range

Weight

SJ-K-33039

5 Tons(4.5 Tonne)2-3/8" thru

5-1/2"51#

SJ-K-33040


7-5/8"69#

SJ-K-33041


10-3/4"98#

SJ-K-33042

5 Tons(4.5 Tonne)11 -3/4" thru

13-3/8"130#

SJ-K-33043

5 Tons(4.5 Tonne)

16" thru20"

213#

35

KING OIL TOOLS КCenter Latch 18 Degree Elevators

Safety Double Lock CombinationEach Half Balanced for HandlingCertified Load TestInterchangeable Parts DesignRegular or Arctic Service

SPECIFICATIONS

Capacity

API Range

Weight

K-MG100

100 Tons

(90.7 Tonne)2-3/8" thru4-1/2" IF

238#

K-RG150

1 50 Tons

(136.1 Tonne)2-3/8" thru

3-1/2"

308#

K-MGG250

250 Tons

(226.8 Tonne)3-1/2" thru

5-1/2"

600#

K-GG350

350 Tons

(31 7.5 Tonne)4" thru5-1/2"

750#

36

KING OIL TOOLS КModel SRA Sucker Rod Elevator

The King sucker rod elevator is specially designed for versatility in workovers and wellservicing operation and for improved operator safety.

The elevator features interchangeable rod plates to accommodate rods from Ув" to 1".Only one King rod elevator is needed on a rig. The elevators are designed with rear springlatches. It prevents operators from exposing their hands and fingers to the lock mecha-nism while operating the elevator.

King rod elevators are constructed of high grade alloy steel with extra body surfaceareas at stress points. They are assembled into a balanced body that pivots freely withouttilting. Body rotates 180°

No.Req.

222222224212

Part Name

Plate %-ЗД in. with screwsPlate '* in. with screwsPlate 1 in. with screwsLatch armSafety latch

Trent LatchCap screwRetainer pinHinge pinLinkSpringSnap ring

Pert Number

SRA-2ASRA-2BSRA-2CSRA-3SRA-4SRA-4FSRA-5SRA-5ASRA-5BSRA-6SRA-7SRA-8

Weight UM.-DZ.

0-80-80-80-120-120-120-20-40-20-20-20-2

"Front safety latch optional.

1. 19" Bail standard.2. 15" Bail engineered for shallow well service and lighter workover.3. Specify Bail size when ordering.

BallSRA 19"SRA 15"

WNflnt34*

26f

Slz» Sucker Rod»

*"-%", W, 1"

W-W, W, 1"

35 KRH and 20 KRH Rod HooksThe King Rod Hooks are designed to handle deep and shallow sucker rod equipment bothefficiently and safely.

Made of heat-treated alloy steel, King's Rod Hooks ensure long, trouble-free service.The Model 35 KRH is spring loaded to reduce the possibility of pin and coupling thread

damage.The 35 KRH is rated at 35 tons.The 20 KRH is rated at 20 tons.


Model35 KRH20 KRH

OverallLength

38*25"

OperatingLength

32"20"

Width8"7"

HooTOpening

Г/6"1%"

WeightPounds

85

45

MODEL 20 KRH MODEL 35 KRH

37

KING OIL TOOLS

Elevator Links Weight and Dimensional DataК

King Oil Tool's forged steel alloy elevator links are especiallydesigned for long life and safety.Each weldless link is forged from a single steel billet, heat treated forstrength and durability and magnafluxed for integrity, then matched insets to maintain elevator balance. Links ЗУг" by 2%" are designed forintermediate to deep drilling and workover, rated 500 ton and 350 tonper set.

Links rated at 250 tons are available in 21Л" stock in two lengths —108" for drilling and 96" for workover.

Rated at 150 tons per set, 1%" links are available in 84", 72", 60", 48"and 36" lengths for shallow drilling, tubing work and portable rigs.

Links rated at 65 tons per set are furnished in 1 '/2" stock and 36"and 30" lengths for water well drilling, mineral exploration and shallowdrilling.

7

1%" SIZE 1V4-SIZE

Dimensions (in inches)Size

Dimensions

A

В

СDEFGHJК

Wt. Lbs. Per SetRates Ton

Per Set

2»«132

1322*4

51/2

8

342

10

514

88

1,000

350

2*ix108

1082*4

51*

8

3*10

5

14

8

8

870

350

2*4x96

962*4

51/2

8

3'*10

5

14

8

8

800

350

2V4X108

108

2V4

51/2

8

2%

10

5

14

В

8610

250

2V4X96

962V4

5*

8

2%

10

514

8

8

550

250

1*4X84

84

1*4

4

6

2%

131*3*168*4

53V2

330

150

1*4X72

721*4

4

6

т13V8

3*168*4

5

3V2

290

150

1*4X60

601*4

4

6

2*13V83*ш

8*4

5

3V2

245

150

1*4X48

481*4

4

6

24i131/83*168*4

531/2

205

150

1*4X36

361*4

4

6

2%

13Ve

3*168*4

5

31/2

165

150

Additional lengths and sizes available on request.

3VS , 2% and 2W SIZE

Wear CapacityUpper Eye Link Size

11/2

DimE

In Tons2 65

115/16 57

1 '/8 55

13A 50

We 46

13/4

DimEIn Tons7/e 150

1 э/1б 1293Л 125 -5/B 116

'/г 105

2V*DimE

In Tons5 250

43/4 2504Vz 2504Vt 250

4 245

23/4

DimE

In Tons5 350

43/4 2984'/2 2804'A 263

4 245

31/2

DirnE

In Tons6 500

53A 4305'/2 4105'A 385

5 365

Lower Eye Link Size _

11/2

Dim К

In Tons1 '/2 65

17/:e 5913/8 5515/1в 491'A 45

13/4

Dim К

In Tons13/4 50

15/8 30

1вЛв 20117/32 14

1 '/2 11

21/4

Dim КIn Tons

21/4 2502Ve 2202Vie 210

2 19817/a 173

23/4

Dim К

In Tons23/* 35025/e 3192<A 29023/8 25025/ifi 245

3V2 fflDimk •

In \о(Ш3'/2 50033/e 4653'/4 4303Ve 395

3 365

38

KING OIL TOOLSКKT Manual Tongs

16,000 ft. Ibs.

Model

16KT

ТУР»Lever

Std.

A

27"

В

33"

с14"

i i V,Replacement Parts 16KT Tong

TONG LINE RETAINERShort Jaw BOLT A.NO NUT

No.Req.

1

1

11

41

211

1

11

41

Part Name

Lever AssemblyTong Line Retainer

Tong Line Retainer Bolt Assembly

Long Jaw Assembly"Die Retainer Pin

Short Jaw Assembly"Tong DieLatch

Latch PlungerLatch Plunger Pin

Hanger AssemblyHanger Bolt AssemblyHinge PinLatch Spring

PartNo.

16-KT-116-KT-8

16-KT-1616-KT-316-KT-3A

16-KT-516-KT-SO16-KT-4

16-KT-1116-KT-1316-KT-2

16-KT-1716-KT-1216-KT-15

wt.Lbs.-Oz.

29-4

2-0

0-8

27-0

0-1

15-0

0-8

8-12

0-8

0-1

14-8

0-601-4

0-2

"All Jaws Assemblies include Cotter Pins.

39

KING OIL TOOLS

"King Stuff11

GS- 143Hydrocarbon

Thread Compound

(Call for complete labanalysis per EPAprocedures)

TECHNICAL DATA

Color GreenOdor NilTemperature Range -40 deg. F to

+ 500 deg. FFlash Point 440 deg. FDropping Point, F (ASTM D217) NoneType Oil SyntheticThickener Fumed SilicateConsistency, Cone Penetration

(ASTM D217) 220 to 300Oil Separation, % Wt. loss

(ASTM D1742) 5 maxOxidation Stability (ASTM D942)

100 hours, psi drop 10 maxRust Preventative Test (ASTM D1743) No. 2Elastomer Compatability Test, % max 29

(Federal Test Standard No. 792a,Method 3603 except substitutegrease for oil specified)

Corrosion Inhibitor ConventionalImadozolineDerivate

EP Additive Ester Type,containing nophosphorous,sulfur, or metal

Ricinus Oil saltFluoronated PolytetrafluorethyleneSilicaE.P. Additive, Corrosion InhibitorColor

GENERAL COMPOSITION

KPVC Slips

^

• Eliminate pipe vises, 2X4's, belts, slings• Economical, faster — sets pipe easily and quickly• Lightweight structural aluminum — only 20 Ib.• Wide 13" base with 7" center hole• Same base plate for 2"-3"-4"-5" pipe• Same slip bodies for 2"-3"-4" pipe (Replace urethane inserts only.)• Separate slip body for 5" pipe

Parts Lists

Part No.

KSA-4PV-5-3P

KSA-4PV-5-3S

KSA-4PV-5-2

KSA-4PV-5-3

KSA-4PV-5-4

Name

Base Plaet

Slip Bodies

2" Inserts

3" Inserts

4" Inserts

Requires

12 (1 set)

2 (1 set)

2 (1 set)

2 (1 set)

Part No.

KSA-4PV-5-4.5

KSA-4PV-5-5S

KSA-4PV-5-5

KSA-4PV-5-6KSA-4PV-5-7

Name

41/2 Inserts

Slip Bodies (for5' Inserts)

5" Inserts

Insert Bolts

Body Bolts &• Nuts

Requires

2 (1 set)

2 (1 set)

2 (1 set)

62

40

KING OIL TOOLS КNOTES

KING OIL TOOLS2215 S. Van Buren, Enid, OK 73703

Phone: (580) 234-4141 USWats: 800-759-7441Fax: (580) 233-6807 Email: [email protected]

king oil tools -...

Documents