knipex general catalogue 2011 en web[1]

GENERAL CATALOGUE 2011/12

PLIERS ABC TECHNICAL BASICS

Cutting Pliersfor cutting or nipping (diagonal, centre and end cutters, carpenters‘ pincers etc.)

Gripping Pliers(flat-, long-nose and water pump pliers etc.)

Combined Pliersfor cutting and gripping (combination, stork beak and radio pliers etc.)

Special Pliersfor special applications, e.g. notching or punching different types of materials (sheet-metal nibbler, tile nibbling pincers etc.)

point

gripping surface

recess (pipe grip)

jaw

flank

additional cutting edge

BASIC SHAPES OF THE JAWS

JOINT CONNECTIONS

TYPES OF JOINTS

Forged-in joint axleThe rivet is part of one handle(forged from one piece) high stability for highest

strain long service life

Joint with inserted rivetA proved, sturdy and precise rivet connection for all standard pliers.

Bolted jointFor particularly demanding requi-rements in terms of precision and smooth operation, e.g. in circlip pliers and cable shears (even the finest multi-stranded conductors have to be cut cleanly).

Lap jointThe two plier halves lie on top of each other but are not milled out.

Single jointHalf the thickness in each pliers handle is milled away in the joint area so that both handles can be laid into each other.

Box jointOne handle on the pliers is slit. The other handle is pushed through this slot. This joint connection can withstand a high level of load and strain because the joint bolt is supported on both sides and the inside handle is guided on both sides.

flat jaws

half-round jaws

round jaws

flat jaws

half-round jaws

round jaws

flat and pointed jaws

box joint

bolted joint

smooth gripping surfaces

serrated gripping surfaces

cross-hatched, knurled gripping surfaces

with opening spring

with lead catcher

angle

electrostatic discharging, dissipative

electronics

VDE tested, also in conformance to GPSG (Equipment and Product Safety Act)insulated according to IEC 60900, usable up to 1000 V AC/1500 V DCinsulated according to DIN VDE 0680/1, suitable for the application up to 1000 V AC / 1500 V DC

conforms to a European directive

mechanically tested in accordance with the equipment and product safety actWEEE marking (Waste Electrical and Electronic Equipment Directive)

weight

length

CUTTING CAPACITIES The maximum values indicated always stay for the performance limit under the most favourable cutting conditions, when the wire is placed as near as possible to the joint.

SYMBOLS

Article no. page

Length ø mm ø mm ø mm ø mm61 0 200 1,0 - 6,0 4,0 3,5 3,0 6762 12 120 0,3 - 1,0 0,7 6764 0 115 2,0 1,0 0,6 6864 11 115 1,4 0,8 6864 12 115 2,0 0,8 0,5 68 / 7064 22 115 0,8 6864 32 120 1,5 1,0 0,5 68 / 7064 42 115 1,5 1,0 0,5 6864 52 115 1,3 6864 62 120 0,6 68 / 7064 72 120 1,5 6867 0 140 4,0 3,1 2,0 1,5 71

160 4,5 3,4 2,5 2,0 71200 5,0 3,8 3,0 2,5 71

68 01 160 4,0 2,8 2,3 71180 4,0 3,2 2,5 71200 4,0 3,5 2,8 71

69 0 130 0,4 - 2,0 0,8 0,8 0,8 7170 110 3,0 2,0 1,2 73

125 3,0 2,3 1,5 73140 4,0 2,5 1,8 73160 4,0 2,8 2,0 73180 4,0 3,0 2,5 73

71 .. 200 6,0 5,2 4,0 3,6 7474 0. 140 3,1 2,0 1,5 80

160 3,4 2,5 2,0 80180 3,8 2,7 2,2 80200 4,2 3,0 2,5 80250 4,6 3,5 3,0 80

74 91 250 5,0 5,0 3,8 3,5 7975 02 125 0,2 - 1,3 1,0 0,6 0,4 8275 12 125 0,2 - 1,3 1,0 0,6 0,4 8275 22 125 0,2 - 1,3 0,9 0,4 0,3 8275 32 125 0,2 - 1,3 0,9 0,4 0,3 8275 52 125 0,2 - 0,8 0,5 0,3 8276 01 125 0,4 - 3,0 2,3 1,5 0,6 8376 03/05 125 0,4 - 2,5 1,8 1,0 0,6 83

Article no. page

Length ø mm ø mm ø mm ø mm

76 12 125 0,4 - 2,5 1,8 1,0 0,6 8376 22 125 0,4 - 2,5 8376 81 125 0,4 - 1,7 1,3 0,8 8377 01/02 115 0,3 - 1,6 1,2 0,6 84

130 0,3 - 2,0 1,5 0,8 8477 11/12 115 0,3 - 1,6 1,2 0,6 8477 21 115 0,3 - 1,3 1,0 84

130 0,3 - 1,6 1,3 8477 22 115 0,3 - 1,3 1,0 84 / 85

130 0,3 - 2,0 1,5 8477 32 115 0,3 - 1,3 1,0 0,5 84 / 8577 42 115 0,3 - 1,3 0,8 84 / 85

130 0,3 - 1,6 1,3 8477 52 115 0,3 - 1,0 0,8 0,5 84 / 8577 72 115 0,3 - 0,8 84 / 8578 03/13 125 0,2 - 1,6 1,0 86 / 8878 23 125 0,2 - 1,0 0,6 8678 31/41 125 0,2 - 1,0 8678 61/71 125 0,2 - 1,6 1,2 86 / 8878 81/91 125 0,2 - 1,6 1,2 0,6 8679 02 120 0,2 - 1,4 1,0 0,6 90 / 9179 02 125 0,2 - 1,7 1,3 0,7 90 / 9179 12 125 0,3 - 1,7 1,3 1,0 0,6 90 / 9179 22 120 0,1 - 1,3 0,8 90 / 9179 22 125 0,1 - 1,7 1,0 90 / 9179 32 125 0,2 - 1,5 1,1 0,6 90 / 9179 42 125 0,1 - 1,5 0,8 90 / 9179 52 125 0,2 - 1,3 0,9 0,5 90 / 9179 62 125 0,1 - 1,3 0,8 90 / 9199 0 200 1,8 1,4 64

220 2,4 1,6 64250 2,4 1,6 64280 2,8 1,8 64300 3,1 1,8 64

99 1 250 3,3 1,8 65300 3,8 2,0 65

centre cutter

cutting edges with bevel

cutting edges with small bevel

cutting edges with very small bevel

cutting edges without bevel

soft wire

medium hard wire

hard wire

piano wire

Cu + Al multi-conductor cab-le, solid and multi-stranded

wire rope

iron

DIRECTION AND POSITION OF CUTTING EDGES

CUTTING EDGE SHAPES CONFORMING TO DIN ISO 5742

CUTTING EDGES TECHNICAL BASICS

Material examples Type of wire Tensile strength

N/mm² kp/mm²

Copper, plastics soft 220 22

Nail, wire pin medium-hard 750 75

Wire rope strand, steel wire

hard 1800 180

Spring steel wire piano wire 2300 230

Safety instructionEach tool should only be used for its specified purpose. When using cutting pliers: beware of wire ends flying off. Wear protective goggles and - if needed - gloves. Be aware of bystanders! Only handles marked with the symbol are insulating.

WIRE CLASSES

End Cutting Nipper

Oblique Cutter

Diagonal Cutter

Centre Cutter

with bevel (outside bevel)

with small bevel (outside bevel)

with very small bevel (outside bevel)

without bevel (outside bevel)

ARTICLE NUMBER

HEAD/HANDLES

0 Pliers black atramentized, head polished

1 Head polished, handles plastic coated

2 Head polished, handles with multi-component grips

3 Pliers chrome plated, handles plastic coated

4 Pliers chrome plated

5 Pliers chrome plated, handles with multi- component grips

6 Pliers chrome plated, handles insulated with multi-component grips, VDE-tested

DIN EN/IEC 60900

7 Pliers chrome plated, handles with dipped insulation, VDE-tested

DIN EN/IEC 60900

STRUCTURE OF ARTICLE NUMBER

Finish e.g.:head polis-hed, handles black atra-mentized

Length e.g.:180 mm

Style e.g.:straight

Basic model e.g.: Combination Pliers

03 0 0 180

Registered Trademarks of the companies

Con-Pearl® PARAT-WERK Schönenbach GmbH + Co. KG

Duspol® Benning, Elektrotechnik and Elektronik GmbH & Co. KG

gesis® Wieland Electric GmbH

Kapton®, E. I. du Pont de KEVLAR®, Nemours and Company Teflon®

Radox® HUBER+SUHNER AG

Phillips® Phillips Screw Company

Pozidriv® European Industrial Service Ltd.

systainer® TANOS GmbH

MC® Multi-Contact AG

Solarlok® Tyco Electronics

No. Article P.

86 Pliers Wrenches 94

87 0 KNIPEX Cobra® 96

87 0 KNIPEX Cobra® XL/XXL 98

85 KNIPEX SmartGrip® 100

87 1 KNIPEX Cobra®...matic 101

87 26 KNIPEX Cobra® VDE 101

87 4 Multiple Slip Joint Spanner 102

87 5 KNIPEX Cobra® ES 103

88 KNIPEX Alligator® 104

89 Water Pump Pliers with tongue and groove joint

106

90 Mini Water Pump Pliers 106

No. Article P.

90 20 Pipe Cutter for plastic conduit pipes and hoses

108

90 25 Pipe Cutter for composite pipes and protective tubes

108

90 25 Pipe Cutter for composite and plastic pipes

109

90 4 Punch Lock Riveters 109

90 55 Sheet Metal Nibbler 110

90 61 Notching Pliers 110

90 7 Revolving Punch Pliers 111

91 0 Tile Nibbling Pincer 111

91 1 Tile Breaking Pincer 111

91 3 Glass Breaking Pincer 112

91 Glass Nibbling Pincers 112

91 6 Flat Nose Grozing Pliers 112

WATER PUMP PLIERS

SPECIAL PLIERS SPECIAL TOOLS

No. Article P.

92 Precision Tweezers 113

92 Precision Tweezers insulated 116

92 Precision Tweezers ESD 117

TWEEZERS

CONTENTS

No. Article P.

01 Combination Pliers Chrome Vanadium

20

08 Mini Combination Pliers 20

02High Leverage Combination Pliers

21

03 Combination Pliers 22

09 ”Lineman‘s Pliers“ 23

No. Article P.

11 Insulation Strippers 24

11 8Electronics Wire Stripping Shears

25

11 9 Electronics Wire Stripper 25

12 Insulation Strippers with shaped blades

25

12 12Precision Insulation Strippers

26

12 40/50 Self-Adjusting Insulation Strippers

28

12 42 KNIPEX MultiStrip 10 29

12 62 Automatic Insulation Stripper

30

12 64 Automatic Insulation Stripper for flat cable

31

12 80 Mini Stripping Tool 31

12 82 Wire Stripper for fibre optics

31

12 85 Stripping Tool for fibre optics

32

13 Electricians‘ Pliers 32

13 72 Universal Pliers for STP data cables

33

14 Diagonal Insulation Strippers

33

15 11Stripping Tweezers for Coated-Wire

34

15 Insulation Strippers 34

16 20 Dismantling Tools 34



16 60 Stripping Tool for coax cables

36

16 65 Dismantling Tool for data cables

37

16 8 Universal Dismantling Tools

37

No. Article P.

19 Round Nose Pliers with cut-ting edge (Jewellers‘ Pliers)

38

20 Flat Nose Pliers 38

22 Round Nose Pliers 39

23Flat Nose Pliers with cutting edges (precision mechanics pliers)

39

25 Snipe Nose Side Cutting Pliers (Radio Pliers)

40

26 Snipe Nose Side Cutting Pliers (Stork Beak Pliers)

41

27Snipe Nose Pliers with centre cutter (Telephone Pliers)

42

28 Assembly Pliers 42

29 Telephone Pliers 43

31 Gripping Pliers (Needle-Nose Pliers) 43

30 Long Nose Pliers 44

32 Relay Adjusting Pliers 45

33 Duckbill Pliers 45

34 Precision Electronics Gripping Pliers

46

34 Precision Electronics Gripping Pliers ESD

47

35 Electronics Pliers 48

35 Electronics Pliers ESD 49

36 Electronics Mounting Pliers 50

37 Gripping Pliers 51

38 Mechanics‘ Pliers 53

No. Article P.

40 Universal Grip Pliers 54

41 Grip Pliers 54

42 Welding Grip Pliers 55

No. Article P.

44 Circlip Pliers for internal circlips

56

46 Circlip Pliers for external circlips

57

44 Circlip Pliers for large internal circlips

58

45 Special Retaining Ring Pliers for retaining rings on shafts

59

46 Circlip Pliers for large external circlips

59

46 Circlip Pliers for grip rings on shafts

59

48 Precision Circlip Pliers for internal circlips

60

49 Precision Circlip Pliers for external circlips

61

No. Article P.

50 Carpenters‘ Pincers 62

51Hammerhead Style Carpenters‘ Pincers

62

55 Farriers‘ Pincers (Tear-off Pliers for vehicle bodywork)

63

57 Unsoling Pincer for horseshoes 63

58 Potters‘ Pincers 63

No. Article P.

99 0 Concretors‘ Nippers 64

99 1 High Leverage Concretors‘ Nippers

65

No. Article P.

61 Bolt End Cutting Nippers 67

62 Electronics Oblique Cutting Nipper

67

64 Electronics End Cutting Nippers / ESD

68/ 70

67High Leverage End Cutting Nippers

71

68 End Cutting Nippers 71

69 End Cutting Nippers for mechanics

71

70 Diagonal Cutters 73

71 KNIPEX CoBolt® Compact Bolt Cutters

74

71 72 Bolt Cutters 76

71 82 Concrete Mesh Cutter 77

72 Diagonal Cutters for plastics 78

72 51 Diagonal Cutter for fibre optics 79

74 91 High Leverage Centre Cutters 79

74High Leverage Diagonal Cutters

80

75 Electronics Diagonal Cutters 82

76 Diagonal Cutters for electromechanics

83


77 Electronics Diagonal Cutters ESD

85

78 Electronic Super Knips® 86

78 Electronic Super Knips® ESD 88

79 Precision Electronics Diagonal Cutters

90

79 Precision Electronics Diagonal Cutters ESD

91

No. Article P.

81 Pipe Gripping Pliers 92

84 Cycle Pliers 92

83 Pipe Wrenches 93

COMBINATION PLIERS

WIRE STRIPPERS + DISMANTLING

TOOLS

GRIPPING PLIERS

GRIP PLIERS

CIRCLIP PLIERS

CARPENTERS’ PINCERS

CONCRETORS’ NIPPERS

CUTTING PLIERS

PIPE WRENCHES

TOOL KITS

No. Article P.

94 10 Pipe Cutter for plastic conduit pipes 118

94 15 Cutter for ribbon cable 118

94 3 Mitre Shears 118

95 02 Vinyl Shears 119

95 03 Shears for KEVLAR® fibres 119

95 05 Combination Shears 120

95 Cable Shears 120/ 122

95 Cable Shears with twin cutting edge

123

95 Cable Shears 124

95 3 Cable Cutters (ratchet action) 125

95 32 Cable Shears with telescopic handles

126/ 127

95 6 Wire Rope Shears 128

95 6 Bowden Cable Cutter 129

95 7 Wire Rope and ACSR-Cable Cutters

129

CABLE AND WIRE ROPE SHEARS

INSULATED TOOLS

DIN EN/IEC 60900

SALES AIDS

CONTROL CABINET

KEYS

ELECTRONICS PLIERS

No. Article P.

97 00 Crimp Grip Pliers 130

97 2 Crimping Pliers 130

97 32 Crimping Pliers 131

97 40 Insertion tool for LSA-Plus and identical

131

97 33 KNIPEX MultiCrimp® 132

97 43 Crimp System Pliers 134

97 49 Crimping Dies 135

97 Locators 136

97 Mounting Tool for MC3 connectors 136

97 50 Crimping Pliers for Scotchlok connectors

137

97 51 Crimping Pliers for Western plugs

137 / 138

97 52 Crimping Pliers, for two-hand operation

139

97 52 Crimping Pliers short design 140

97 52 Crimping Pliers ”Preciforce“ 141

97 52 Four-Mandrel Crimping Pliers for turned contacts

142

97 53 Self-Adjusting Crimping Pliers for end sleeves

144 / 145

97 54 Crimping Pliers for micro plugs 146

97 Crimping Pliers for end sleeves

146 / 147

97 90 Crimp Assortments 148

97 91 Tool Cases for Photovoltaics

150 / 151

97 99 Cable Connectors 152

No. Article P.

01/02/ 03

(High Leverage) Combination Pliers

156/157

11 Insulation Strippers 157/158

20 Flat Nose Pliers 158

22 Round Nose Pliers 159

25 Snipe Nose Side Cutting Pliers

159/160

70 Diagonal Cutters 161

74 High Leverage Diagonal Cutters 161

86 07 Pliers Wrench insulated 162

88 KNIPEX Alligator® 162

87 26 KNIPEX Cobra® VDE 163

92 Precision Tweezers 164

95 Cable Shears 165-167

95 3 Cable Cutters (ratchet action)

168

95 7 Wire Rope and ACSR-Cable Cutter

168

97 68 Crimping Pliers for end sleeves

169

98 0 Open End-/Box Wrenches 170/171

98 0 Nut Drivers 172

98 07 Adjustable Wrench 173

98 Screwdrivers from 173

98 Hexagon Sockets 177/179

98 Torque Wrench 179

98 5 Cable Knives 180/181

98 5 Dismantling Knives 180

98 60 Voltage tester 181

98 Plastic Slip-On Caps 182

98 Electricians‘ Gloves 182

98 Insulating Mats from rubber

183

98 90 Puk® Junior Hacksaw 183

98 Tool Cases from 183

No. Article P.

00 19 Test Supports 208

00 19 Sales Display 208

00 19 Rotary Sales Stand 209

00 19 Tool Bars (Pegboards) 210

00 19 Show-Cabinets for product presentation

211

00 19 Hooks for pegboards 212

00 19 Brochure Holder 212

00 19 Pliers Racks 213

00 19 Sales Displays 214

No. Article P.

00 19 Counter Displays 191

00 19 Cobra® range in sales display

192

00 19 Tool Roll 192

00 19/20

Circlip Pliers Sets 193

00 20 Pliers Sets in a foam tray

from 194

00 20 Pliers Sets from 193

00 21 Tool Cases from 196

No. Article P.

11 92 Electronics Wire Stripper 25

34 Precision Electronics Gripping Pliers

46

35 Electronics Pliers 48

35 Electronics Pliers ESD 49

36 Electronics Mounting Pliers

50

62Electronics Oblique Cutting Nipper

67

64Electronics End Cutting Nippers

68

64 Electronics End-Cutting Nippers ESD

70


76 Diagonal Cutters for electromechanics

83

77 Electronics Diagonal Cutters

84

77 Electronics Diagonal Cutters ESD

85

78 Electronic Super Knips® / ESD

86 / 88

79 Precision Electronics Diagonal Cutters / ESD

90 / 91

92 Precision Tweezers from 116

94 15 Cutter for ribbon cable 118

00 20 Electronics Pliers Sets 195

TOOL BAGS AND TOOL

CASESNo. Article P.

00 19 Tool Pouches 203

00 21 Tool Bags and Tool Cases

from 203CRIMPING PLIERS

AND -ASSORTMENTS

THE RANGE OF PRODUCTS

No. Article P.

12 12 11Precision Insulation Strippers

26

97 43 200 Crimp System Pliers 134

97 49 65 2Mounting Tool for MC3 connectors

136

97 91Tool Cases for Photovoltaics

150/ 151

TOOLS FOR PHOTOVOLTAICS

00 11 Control Cabinet Keys 188

00 11 Profi-Key 188

00 11 Universal Key 188

00 11 Pen-Style Control Cabinet Key

189/ 190

00 11 Pen-Style Profi-Key 189

5

HOW EVERYTHING BEGAN – AND A SIMPLE PRINCIPLE

1882 Carl Gustav Putsch set up his own small forge shop in Cronen-berg (now a part of Wuppertal).

1922 Carl Putsch takes over mana-gement. The company develops into an industrial firm.

1942 KNIPEX, the brand, is created and registered.

1954 Karl Putsch (photo left), the grandson of the company founder, takes over management of the family-owned company. Numerous innovations and modern production technology characterise the develop-ment.

1987 Ralf Putsch joins the com pany. International sales are seriously ex-panded. Other tool manufacturers become part of the KNIPEX Group.

Carl Gustav Putsch wanted to stand on his own two feet after completing his apprentice-ship as blacksmith with his father. He therefore set up his own business in 1882 and forged carpenters‘ and farriers‘ pincers with two journeymen, 60 pieces per day. The other processes were also carried out in careful manual labour. The quality was sought after, the small enter-prise grew.

The next generations were able to build continuously on these foundations. We have retained an independent family-owned company up to the present day. A lot has changed since the first years. Over time, the workshop turned into a factory with modern machinery and conti-nuously improving technology. New types of pliers and pioneering innovations were added. The number of supplied countries grew steadily.

However, our fundamental principle has stayed in place: remain faithful to a product group, concentrate all strengths on it and be „simply the best“ in pliers. Don‘t get side-tracked, in-stead create more performance and quality in a single segment. This is what KNIPEX stands for as today‘s leading brand in pliers.

6

FOR WHOM WE MAKE PLIERS

They are constantly in our mind: People who work with tools professionally. Who need to be able to rely on their tools, even when the going gets tough. Who expect their tools to last a long time. In other words: Users who are demanding in every respect and who want only the best.

We offer these users a range of around 1,000 different pliers. With this choice we can provide exactly the right tool for every application - and always in a suitable design and size.

Because the verdict of the professionals is our benchmark, we are always looking for their feed-back. About how they work with their pliers and what‘s important to them, so that we can understand precisely and in detail what matters to them.

Paramount is to know what makes their work easier, quicker and safer. That is, the subject of ergo nomics, adapting working appliances to their users. Despite high performance, tools should never stress a user more than necessary. Here, for example, the good design of pliers handles is not the only criterion. We always find new ways of saving strength and relieving the whole hand-arm system.

9

QUALITY IN EVERY DETAIL

Sometimes we give our pliers a really hard time. We try to destroy them to find out what makes them good and long-lasting. Because we don‘t want to leave anything to chance, we take a long, careful look.

Correctly hardened, this steel guarantees optimum cutting performance and service life. That‘s why we use it for our pliers – even if it has to be produced especially for us, costs more and is hard to process. But our high product demands require this.

The rivet of the high-leverage diagonal cutter also has to stand up to a lot of stress. That‘s why we literally give it backup: we forge it straight onto the pliers. This means extra effort – we have to precision mill the rivet to a few hundredth millimeters. Satisfied users are worth this effort.

And then there are, no less important: the angles, the sharpness, the hardness, the toughness of the cutting edges. The precision and smooth movement of the joint. The handle design and the finish: we keep reviewing these subjects, we research, test and improve.

Many trials, for example, have shown us that high-leverage diagonal cutters for very hard wire should be alloyed at best with 0.8 % carbon and certain defined parts of chromium and vanadium.

10

MADE IN WUPPERTAL, GERMANY

A lot has to come together so that we can make the best pliers.First of all, the special material. Then: modern processing methods and machines. We want to work with high precision and efficiently at all times.

The machines we require for our special needs are not always available on the market. Then we construct these ourselves. Our mechanical engineers come up with state-of-the-art solutions even for tricky tasks.

And last but not least: our employees. With their comprehensive experience, their knowledge and skills they make sure that everything turns out precisely as our customers expect. So that we can keep the KNIPEX promise.

Our pliers run through many production steps which are all carefully coordinated. From forging to machining, hardening, surface finishing and all the way to packing, these steps are all carried out under the one roof. This means that we can have a direct and complete influence on how our products are created.

The short distances allow us to respond quickly and implement improvements immediately.

13

THE THINK TANK

When we have achieved something we are happy – but we don‘t stop there. For us, better is the enemy of the good. And we like to be the first to have the good ideas for better pliers.

We continuously work on new products and product advantages which offer our users tangible added value. For example by saving handforce when cutting or they can adjust pliers for gripping quicker and with more precision. Or they can do without a heavy tool because a more compact one can do the same job.

No matter whether it‘s a small improvement or a totally new idea: everything is meticulously thought out and designed with state-of-the-art software. New models are then put through the acid test – with the help of computer simulations in the test lab and in user testing. The results are then used to further optimise the product, it is re-tested and finally released for production.

By the time they‘re on the market our pliers have already come a long, hard way.

14

OUR CUSTOMERS

Reliably, confidently and long-term – this is how we wish to collaborate with our customers. We have been doing precisely this for decades with many of them. We offer high quality, perfor-mance, good service and contact partners who know what it‘s all about. We want working with us to be easy and pleasant.

Our brand is known and appreciated by consumers. We offer various support for the sale of our products. We visit users together with our distributors to present our tools. We train our partners‘ field salesforce because a lot can be said about our pliers which the salesperson can use as con-vincing arguments.

Our understanding of partnership also means that we do not sell directly to end users. And there are no exceptions.

Today, customers in more than 100 countries bank on our products. We reach them via a con stantly enlarging, worldwide network of agencies, our own subsidiaries and importers. By ob serving the many markets we can gain insights and discover important trends, which will be beneficial to the up-to-dateness and competence of our range. Our customers also benefit from this.

15

ALICATES P INZE

PINCESTENGER

KERPETEN

ZANGE

ALICATEPLIERSTANG

17

OUR VALUES – OUR EMPLOYEES

We want to be successful and do a lot to achieve this. But we don‘t want economic success at any price and not at the expense of values which are important to us.

Our aspirations are to act and operate sustainably. The longevity of our products is only one aspect of many.

We feel closely linked with our location. That is why we are particularly aware that we have a responsibility towards our environment and society – and thereby our future generations. We want to treat resources carefully and not burden nature more than absolutely necessary.

We engage ourselves in many ways in our sphere, in particular in the sectors of education, social policy and culture.

Our employees are particularly important to us. They provide the basis for our success with their knowledge and skills, their commitment and ideas. We train them very thoroughly and support them when they want to develop themselves and learn something new. We put emphasis on a good an fair cooperation and know that we can only attain our high targets jointly.

18

97 91 01

SPECIAL TOOLS FOR PHOTOVOLTAICS ALL WORK STEPS WELL CO-ORDINATED FOR BEST RESULTS

There is a steadily increase of electrical power produced by photovoltaic plants (PV systems). The output from this environmentally friendly source of energy rises each year by about 20 % world wide. However, the share in the total po-wer generation is still below 0.3 % worldwide, which means there is still rich potential for growth. This makes photo voltaic a profitable sphere of activities for trade and for electrical contractors.

The photovoltaic tools from KNIPEX, customized for cutting, stripping and crimping the special photovoltaic cables and connectors, offer professional and reliable work results and ensure that the relevant requirements, such as e.g. Ral GZ 966, are met.

The requirements for a technically perfect installation of the photo voltaic systems are very high. It is a demanding task to create an electrically efficient and constantly reliable connec-tion in combi nation with high mechanical requirements.

19

Multi-Contact HirschmannTycoWieland and others

Article No. 97 91 01: all tools required for assembly in one case equipped with crimping dies for standard solar cable connectors

Tool Case for Photovoltaics

for contacts from:

SPECIAL PHOTOVOLTAIC RANGE FROM KNIPEX

Cut effected with a Cable Shears: easy, clean cut without any deformation of the cable.

Huber + Suhner

Multi-Contact MC3

Multi-Contact MC4

Hirschmann

Tyco

Wieland

Locatorsfor an exact connector positioning in the crimp profile

High demands in terms of results require the use of high-quality special tools also. These must be adapted precisely to suit systems from various manufacturers.

As the systems are not compatible with each other, each type of connector requires a set of individual crimping dies. The range is completed by locators to support quick, easy and precise work.

20

COMBINATION PLIERS

01Combination Pliers Chrome Vanadium

DIN ISO 5746 IEC 60900 DIN EN 60900

01 06 190

for heaviest duty with gripping zones for flat and round material, suitable for versatile use with cutting edges for soft, hard and piano wire long cutting edges for thicker cables cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC particularly wear resistant gripping jaws; hardness of the gripping jaws approx. 53 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened

Cutting capacitiesArticle No. EAN

4003773- mm

Pliers Handles

Ø mm Ø mm Ø mm mm² g

01 06 160 040729 160 chrome plated

insulated with multi-component grips, VDE-tested

2.0 1.5 10.0 16.0 220

01 06 190 040415 190 2.5 2.0 13.0 25.0 320

08Mini Combination Pliers

08 05 110

compact combination pliers for professionals and hobbyists with gripping zones for flat and round material, suitable for versatile use with cutting edges for soft and hard wire cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC Vanadium electric steel; forged, oil-hardened


4003773- mm

Pliers Handles


08 05 110 034957 110 chrome plated with multi-component grips 2.5 1.6 9.0 10.0 85

21

COMBINATION PLIERS

02

02 01 180

02 02 180

02 05 180

02 06 180

02 07 225


4003773- mm

Pliers Head Handles


02 01 180 033134 180

black atramentized polished plastic coated

2.5 2.0 11.5 16.0 202

02 01 200 039679 200 2.8 2.2 13.0 25.0 298

02 01 225 013198 225 3.0 2.5 14.0 25.0 358

02 02 180 034896 180

black atramentized polished with multi-component grips

2.5 2.0 11.5 16.0 240

02 02 200 034902 200 2.8 2.2 13.0 25.0 342

02 02 225 043379 225 3.0 2.5 14.0 25.0 409

02 05 180 043072 180

chrome platedwith multi-component grips

2.5 2.0 11.5 16.0 238

02 05 200 043089 200 2.8 2.2 13.0 25.0 342

02 05 225 010005 225 3.0 2.5 14.0 25.0 400

02 06 180 010012 180

chrome plated insulated with multi-component grips, VDE-tested

2.5 2.0 11.5 16.0 247

02 06 200 010029 200 2.8 2.2 13.0 25.0 343

02 06 225 010036 225 3.0 2.5 14.0 25.0 401

02 07 200 022299 200 chrome plated

with plastic dipped insulation, VDE-tested

2.8 2.2 13.0 25.0 380

02 07 225 022305 225 3.0 2.5 14.0 25.0 486

35 % less effort required than with conventional combination pliers easier work due to optimised leverage with cutting edges (hardness approx. 63 HRC) for soft and hard wire and piano wire long cutting edges for thicker cables with gripping zones for flat and round material, suitable for versatile use High-grade special tool steel, forged, oil-hardened

High Leverage Combination Pliers DIN ISO 5746

Easier cutting. Powerful gripping, bending and pulling.

22

COMBINATION PLIERS

03Combination Pliers DIN ISO 5746

03 01 180

03 02 180

03 05 180

03 06 180

with gripping zones for flat and round material, suitable for versatile use with cutting edges for soft and hard wire long cutting edges for thicker cables cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC Special tool steel, forged, oil-hardened


4003773- mm

Pliers Head Handles


03 00 180 015161 180

black atramentized polished

3.4 2.2 12.0 16.0 205

03 00 200 015178 200 3.8 2.5 13.0 16.0 255

03 00 250 015185 250 3.8 2.5 15.0 25.0 444

03 01 140 015192 140


2.8 1.8 9.0 10.0 112

03 01 160 013235 160 3.1 2.0 10.0 16.0 187

03 01 180 013242 180 3.4 2.2 12.0 16.0 216

03 01 200 013259 200 3.8 2.5 13.0 16.0 276

03 01 250 015222 250 3.8 2.5 15.0 25.0 489

03 02 160 023203 160

black atramentized polishedwith multi-com-ponent grips

3.1 2.0 10.0 16.0 223

03 02 180 023197 180 3.4 2.2 12.0 16.0 254

03 02 200 034940 200 3.8 2.5 13.0 16.0 322

03 05 140 039730 140

chrome plated with multi-com-ponent grips

2.8 1.8 9.0 10.0 139

03 05 160 039518 160 3.1 2.0 10.0 16.0 222

03 05 180 034933 180 3.4 2.2 12.0 16.0 254

03 05 200 041146 200 3.8 2.5 13.0 16.0 324

03 06 160 021902 160

chrome plated

insulated with multi-com-ponent grips, VDE-tested

3.1 2.0 10.0 16.0 228

03 06 180 021926 180 3.4 2.2 12.0 16.0 264

03 06 200 033776 200 3.8 2.5 13.0 16.0 326

03 07 160 015307 160

chrome plated with plastic dip-ped insulation, VDE-tested

3.1 2.0 10.0 16.0 254

03 07 180 015314 180 3.4 2.2 12.0 16.0 285

03 07 200 015321 200 3.8 2.5 13.0 16.0 339

03 07 250 015345 250 3.8 2.5 15.0 25.0 597

23

COMBINATION PLIERS

09Lineman‘s Pliers American style

DIN ISO 5746 ASME B107.20

09 01 240

09 02 240

09 11 240

solid construction for heaviest strain; universally applicable high transmission ratio for easy cutting requires 40 % less effort compared with conventional combination pliers thanks to optimised transmission ratio ergonomically optimised handle shape for firm contact to the hand and fatigue reducing operation particularly effective cross-hatched knurled gripping zone in the jaws – for strong gripping and pulling additional gripping zone below the joint for powerful leverage and pressing performance with cutting edges for soft and hard wire cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC Vanadium electric steel; forged, oil-hardened

09 11 240 / 09 12 250with fish tape puller in the joint gap; with universal mandrel crimping point below the joint

Gripping zone below the joint for powerful leverage

Cross-hatched, knurled gripping zone for firm gripping and pulling, e.g. for fence construction

Long cutting edges for cutting flat cables 09 11/12 240: fish tape puller in the joint gap

09 11/12 240: universal mandrel crimping area below the joint


4003773- mm

Pliers Head Handles

Ø mm Ø mm g

09 01 240 064992 240 black atramentized polished with non-slip plastic coating 4.6 3.0 435

09 02 240 065005 240 black atramentized polished with multi-component grips 4.6 3.0 470

09 11 240 071952 240 black atramentized polished with non-slip plastic coating 4.6 3.0 435

09 12 240 071969 240 black atramentized polished with multi-component grips 4.6 3.0 470

24

WIRE STRIPPERS AND DISMANTLING TOOLS

11Insulation Strippers

11 01 160

11 02 160

11 05 160

11 06 160

for single, multiple and fine stranded conductors with plastic or rubber insulation max. 5.0 mm dia. or resp. 10.0 mm² cable cross section easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut Special tool steel, forged, oil-hardened

Stripping capacitiesArticle No. EAN

4003773- mm

Pliers Head Handles Ø mm mm² AWG

g

11 01 160 013556 160 black atramentized

polished plastic coated 5.0 10.0 7 131


polished with multi-component grips 5.0 10.0 7 165

11 05 160 039570 160 chrome plated with multi-component grips 5.0 10.0 7 157

11 06 160 021933 160

chrome plated insulated with multi-component grips, VDE-tested

5.0 10.0 7 166

11 07 160 015499 160 chrome platedwith plastic dipped insulation, VDE-tested

5.0 10.0 7 180


polished with multi-component grips 5.0 10.0 7 156

11 15 160 042471 160 chrome plated with multi-component grips 5.0 10.0 7 155

11 17 160 015505 160 chrome plated with plastic dipped insulation, VDE-tested

5.0 10.0 7 181

Prismatic blade:The red area is cut over four surfaces. Works with highly-elastic materials also.

25

118 Electronics Wire Stripping Shears

11 82 130

for cutting and stripping single, multiple and fine-stranded conduc-tors with diameters up to 1.0 mm easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut with opening spring Special tool steel, oil-hardened

Article No. EAN4003773- mm

Head Handles Stripping capacitiesØ mm g

11 82 130 071648 130 polished with multi-component grips 0.03-1.0 75


119 Electronics Wire Stripper

11 92 140

for single, multiple and fine stranded cables having a diameter from 0.1 up to 0.8 mm, with plastic or rubber insulation easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut with opening spring the mirror polish together with a fine film of oil offer effective rust protection - no circuit faults caused by peeling chrome from plated tools Special tool steel, forged, oil-hardened



11 92 140 016908 140 mirror polished with multi-component grips 0.1 - 0.8 99

12Insulation Strippers with shaped blades

12 11 180

with replaceable blades for 4 or 6 different conductor cross-sections leave wire undamaged thanks to precision-ground blade shapes, even multi-stranded conductors are stripped gently during stripping, the wire is held firmly by clamping jaws with length stop for constant stripping length during repetitive work a spring leads the stripper back to the starting position Pliers body: aluminium Blade: special tool steel, oil-hardened


Pliers Handles Stripping capacitiesØ mm

Stripping capacitiesmm²

AWG

g

12 11 180 000792 180 black lacquered with plastic grips

0.5 / 1.2 / 1.6 / 2.0 368

12 21 180 000815 1800.5-0.75 / 1.0 / 1.5 /

2.5 / 4.0 / 6.020-19 / 17 /15 /

13 /11/ 10366

12 19 180 022145 1 pair of spare blades for 12 11 180


12 11 180: wire diameter in mm 12 21 180: wire cross-sections in mm²

26


12 12 Precision Insulation Strippers

with adapted blades

12 12 02

12 12 06

12 12 11

Precisely and reliably

Two pairs of blades (1) cut the insulation to a complete extent. Then the blade pairs move apart, and thus the insulation is removed form-fit (2). The pliers open automatically after the stripping procedure.

form-fit stripping also of difficult-to-remove insulating materials such as Teflon®, silicone, Radox®, Kapton® and rubber; multi-layer too a second pair of blades holds the remaining insulation reliably in place blades are shaped precisely to the respective conductor cross-section with an adjustable length stop when cutting the same stripping lengths during repetitive work Pliers body: steel Blade: special tool steel, oil-hardened

12 12 02 with additional cable guide for exact positioning of the cable in the stripping area of the blade 12 12 11 / 12 12 12 for solar cables specially adapted to multi-layered and Radox® insulation; with additional cable support for a better centring of multi-layer insulated conductors in the stripping profiles

maximum cable cross-section (in mm²) per profile:

Article No.

EAN4003773-

mm

Pliers Handles Stripping capacitiesmm²

AWG

g

12 12 02 048077 195

burnished with multi-component grips

0.03 - 2.08 32 - 14 447

12 12 06 049005 195 0.14 - 6.00 26 - 10 445

12 12 10 049012 195 2.5 - 10.0 13 - 7 445

12 12 11 062998 195 burnished with multi-component grips

1.5 - 6.0 15 - 10 449

12 12 12 073758 195 4.0 - 10.0 11 - 7 450

12 19 02 049036 1 set of spare blades for 12 12 02





12 12 1012 12 06

12 12 02

12 12 1212 12 11

Kapton®/Teflon® is a registered trademark of E. I. du Pont de Nemours and Company


12 12 02 with cable guide and length stop Precise cutting of the insulation to a complete extent

Positive stripping thanks to precise shape of the blades

Automatic stripping of the insulation

Principle of operation with adapted blades

Properly and precise stripping with an annular cut through the complete insulation. This is particularly important with conductors, which must be stripped precisely.

This works without any problem even with difficult materials such as Teflon®, Radox® and multilayer insulations.

0.03 mm2

10 mm2

28

1240/50 Self-Adjusting Insulation Strippers

12 40 200

for single, multiple and fine stranded conductors with plastic or rubber insulation adapts automatically to the respective cable cross-section; prevents damage to the conductor cutting depth can be adjusted for different insulation materials with wire cutter for copper and aluminium wires, multiple stranded up to 10.0 mm² and single stranded up to 6.0 mm² smoothly operating mechanism stripping blades and clamping jaws easily replaceable low weight Body: plastic, fibreglass-reinforced Blade: special tool steel, oil-hardened

12 40 200for thin ribbon cables up to 10.0 mm width in a single pass

Adjustable length stop Precise stripping prevents damage to the conductor

Wire cutter for multiple stranded wire cables up to 10.00 mm²



AWG Length stopmm g

12 40 200 026662 200 0.03 - 10.0 32 - 7 3.0 - 18.0 202

12 50 200 034407 200 2.5 - 16.0 13 - 5 200


12 49 02 026686 1 pair of spare clamping jaws for 12 40 200

12 49 03 026693 Spare length stop for 12 40 200


12 59 02 034421 1 pair of spare clamping jaws for 12 50 200

STRA

IGH

T BL

AD

E


29


Mode of operation of straight cuttersModels 12 40 200 and 12 42 195

An incision is made in the red area only.

Not suitable for highly-flexible or armoured insulation materials or for multi-layered insulation.

1242

12 42 195

Patented mechanicsThe incision depth of the stripping blade adjusts fully auto-matically to the diameter of the wire and accordingly also to the thickness of all standard insulating materials. There is no need for any manual adjustment which is still necessary when other conventional pliers with a wide wire-stripping range are used.

Wire cutter for multiple stranded wire cables up to 10.0 mm²

Steel restrain jaws with cutting edges avoid skidding of the cable

Precise stripping from 0.03 to 10.0 mm² without re-adjustment



AWG

g

12 42 195 054580 195 0.03 - 10.0 32 - 7 136

12 49 21 057581 Spare blades block for 12 42 195


fully automatic adjustment to commercially used single-, multi- and fine-stranded conductors with standard insulation throughout the entire capacity range from 0.03 to 10.0 mm² no manual fine adjustment required, no damage to the conductors the clamping jaws made of steel with integrated cutting edge hold the cable in a way that prevents slipping without damaging the remaining insulationwith wire cutter for copper and aluminium conductors, multi- stranded up to 10.0 mm² and single-stranded up to 6.0 mm² particularly smooth-running mechanics and very low weight replaceable blades block and length stop handle with soft-plastic zone for a steady grip Body: plastic, fibreglass-reinforced Blade: special tool steel, oil-hardened

KNIPEX MultiStrip 10 Automatic Insulation Stripper

Stripping without re-adjustment from 0.03 to 10.0 mm²

30


1262 Automatic Insulation Stripper

12 62 180

compact standard tool at a favourable price for all current cable cross-sections and insulating materials for single, multiple and fine stranded cables of 0.2 up to 6.0 mm² with standard insulation adapts automatically to the respective cable cross-section; prevents damage to the conductor high operation comfort thanks to handy shape and low weight narrow head style for use in confined areas with wire cutter for copper an aluminium wires up to 2.5 mm² with adjustable length stop from 6.0 - 18.0 mm for cutting the same stripping lengths during repetitive work Body: plastic, fibreglass-reinforced Blades: special tool steel, oil-hardened, interchangeable

Precise stripping from 0.2 up to 6.0 mm²Wire cutter up to 2.5 mm² Stripping in confined areas



AWG

g

12 62 180 054573 180 0.2 - 6.0 24 - 10 151



1264 Automatic Insulation Stripper

for flat cable

12 64 180

for PVC insulated flat cables up to a max. 12 mm width and 0.75 to 2.5 mm² adapts automatically to the various conductor heights; prevents damage to the conductor long stripping lengths possible blade replaceable smoothly operating mechanism low weight Body: plastic, fibreglass-reinforced Blade: special tool steel, oil-hardened



AWG

g

12 64 180 073284 180 0.75 - 2.5 19 - 13 125


0.2

mm

2

6.0

mm

2

31


1280 Mini Stripping Tool

12 80 100 SB

precise stripping, stepwise adjustment to the conductor diameters with wire cutter adjustable length stop from 4.0 - 15.0 mm with locking device Housing: plastic, impact-proof

12 80 040 SBfor thin copper conductors dia. 0.12 to 0.4 mm


Stripping capacitiesØ mm

AWG

g

12 80 040 SB 071655 100 0.12 - 0.4 36 - 26 35

12 80 100 SB 043119 100 0.30 - 1.0 28 - 18 34

1282 Wire Stripper for fibre optics

12 82 130 SB

to remove primary and secondary coating of fibre optics Chrome vanadium electric steel in special quality, oil-hardened


Pliers Handles Stripping capacitiesØ mm g

12 82 130 SB 050094 130 burnished with plastic handles primary-coating: 0.125 mm secondary-coating: 0.250 mm 69

32

13Electricians‘ Pliers

13 01 160

13 02 160

13 05 160

the ideal pliers for cable work for gripping and bending wire for cutting soft, medium and hard wire precision cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC with precision stripping holes for crimping end sleeves (ferrules) Vanadium electric steel; forged, oil-hardened

Gripping Cutting

Stripping Crimping 0.5 to 2.5 mm²


4003773- mm

Pliers Head Handles Stripping capacitiesmm² Ø mm Ø mm g

13 01 160 034971 160 black atramentized polished plastic coated 0.5 - 0.75 / 1.5 / 2.5 2.5 1.6 112

13 02 160 010470 160 black atramentized polished with multi-component grips

0.5 - 0.75 / 1.5 / 2.5 2.5 1.6 139

13 05 160 071426 160 chrome platedwith multi-component grips

0.5 - 0.75 / 1.5 / 2.5 2.5 1.6 139


1285 Stripping Tool for fibre optics

12 85 100 SB

to remove primary coating of fibre optics Ø 0.125 mm blade dia. 0.18 mm, hole for cable feeding 0.30 mm dia. adjustable length stop Housing: plastic, impact-proof


Stripping capacitiesØ mm g

12 85 100 SB 043126 100 to remove primary coating of fibre optics Ø 0.125 mm 44

33


1372 Universal Pliers for STP data cables

13 72 160 SB

for cutting the entire cable, the single conductor, the shield and the plastic core steel needle at the joint for longitudinal scratching of the shield foil prismatic blades below the joint for dismantling the cables Chrome vanadium electric steel in special quality, oil-hardened


Pliers Handles

g

13 72 160 SB 052319 160 burnished with multi-component grips 102

14Diagonal Insulation Strippers

14 22 160

14 25 160

14 26 160

the essential pliers for electrical installation work precision stripping holes for single (solid) conductors of 1.5 and 2.5 mm² induction hardened precision blades for soft wire up to 4.0 mm dia., cutting edge hardness approx. 60 HRC Vanadium electric steel; forged, oil-hardened

Multi-functional: cutting and stripping


4003773- mm

Pliers Head Handles Stripping capacitiesmm²

AWG

Ø mm Ø mm g


polishedwith multi-compo-nent grips

1.5 + 2.5 15 + 13 2.5 1.5 206

14 25 160 028697 160 chrome plated with multi-compo-nent grips

1.5 + 2.5 15 + 13 2.5 1.5 206

14 26 160 040279 160

chrome platedinsulated with multi-component grips, VDE-tested

1.5 + 2.5 15 + 13 2.5 1.5 216

34


1511 Stripping Tweezers for Coated-Wire

15 11 120

for stripping off varnished insulation on copper wires blades for other wire diameters available as spare parts Tweezers body: spring steel, oil-hardened Handle shells: plastic

Article No. EAN4003773-

15 19 005 021551 1 pair of spare blades for 15 11 120 Ø 0.5 mm15 19 006 021568 1 pair of spare blades for 15 11 120 Ø 0.6 mm15 19 008 021575 1 pair of spare blades for 15 11 120 Ø 0.8 mm15 19 010 021582 1 pair of spare blades for 15 11 120 Ø 1.0 mm

Artikel-Nr. EAN4003773- mm


15 11 120 015550 120 0.6 34


15 61 160

for stripping thin cablesaccurate boring to match dia-meter of wire, precise stripping prism; non-adjustable with opening spring Chrome vanadium electric steel, forged, oil-hardened



15 51 160 044451 160

polished plastic coated

0.5 101

15 61 160 014843 160 0.6 102

15 81 160 015574 160 0.8 102

1620 Dismantling Tools

16 20 16 SB

16 20 165 SB

for stripping all common round cables self-tightening holding lever with adjusting screw for cutting depth adjustment turnable blade for circular and longitudinal cutting spare blade inside the handle secure grip due to soft compo-nent material on handle and holding lever to avoid slipping

16 20 165 SBwith knife and hook blade, protective cap included



16 20 16 SB 060451 130 4.0 - 16.0 95

16 20 28 SB 060468 130 8.0 - 28.0 95

16 20 165 SB 043133 165 8.0 - 28.0 85

16 29 165 043140Spare blade for 16 20 16 SB / 16 20 28 SB / 16 20 165 SB

Housing: plastic, impact-proof

35


1630 Dismantling Tool for dismantling round cable

sheaths made of PVC, rubber, silicone or PTFE from 6.0 - 29.0 mm dia. self-tightening holding lever with knurled nut for cutting depth adjustment changing from circular to longitudinal cutting by turning the tool body spiral cutting for removing intermediate pieces replaceable blade Housing: plastic, impact-proof



16 30 135 SB 033349 135 6.0 - 29.0 120

16 39 135 027317 Spare blade for 16 30 135 SB

16 30 135 SB

1640 Dismantling Tool

16 40 150

for dismantling round cables exceeding 25.0 mm dia. removes all kinds of insulation layers suitable for longitudinal and circular cutting cutting depth can be adjusted up to 5.0 mm replaceable blade (both sides can be used) Tool body: plastic, fibreglass-reinforced

Setting the tool for longitudinal cut Longitudinal cut

Turning the tool for circumferential cut Circular cut

Adjustable cutting depth



16 40 150 026709 150 > 25 210

16 49 150 026716 Spare blade for 16 40 150

36

1660 Stripping Tool for coax cables

16 60 05 SB

for stripping coax cables (RG 58, RG 59 and RG 62) for stripping outer sheath, shield and insulation in a single pass with three built-in blades the cutting depth of each blade can be adjusted individually by means of a hexagonal key (Allen key) the blade spacing remains constant Housing: plastic, impact-proof

Dismantling of a coax-cable in three steps

3 stripping steps in one operation


Cable type

g

16 60 05 SB 044888 105 RG 58, RG 59 and RG 62 73


1660 Stripping Tool for coax cables

16 60 100 SB

for dismantling and stripping all common coax cables between 4.8 - 7.5 mm dia. (e.g. for TV- and satellite antenna), also suitable for PVC round cable 3 x 0.75 mm² with length scale 5.0 - 20.0 mm double shell, folding back stripping tool with opening spring and locking device Body: plastic, fibreglass-reinforced



16 60 100 SB 040811 100 Coax-cables 4.8 - 7.5 round cables 3 x 0.75 mm² 39

37


1665 Dismantling Tool for data cables

16 65 125 SB

for stripping UTP and STP data cables with diameters of 4.5 to 10.0 mm stripping device for cross-sections 0.2 / 0.3 / 0.8 / 1.5 / 2.5 / 4.0 mm² double shell, folding back stripping tool with opening spring and locking device practical clip for easy transport Body: plastic, fibreglass-reinforced


Types of cables Stripping capacitiesØ mm

Stripping capacitiesmm² g

16 65 125 SB 043157 125 CAT 5, CAT 6, CAT 7, Twisted-Pair (UTP/STP) 4.5 - 10.0 0.2 - 4.0 50

168 Universal Dismantling Tools

16 80 125 SB

16 85 125 SB

for dismantling and stripping all common round and damp-proof installation cables between 8.0 - 13.0 mm dia. (e.g. 3 x 1.5 mm² up to 5 x 2.5 mm²) also for use in conduit and distribution boxes double shell, folding back stripping tool with opening spring and locking device practical clip for easy transport Body: plastic, fibreglass-reinforced

16 85 125 SBwith additional blade for longitudinal cuts; telescopic blade inside; stripping device for cross-sections 0.2 / 0.3 / 0.8 / 1.5 / 2.5 / 4.0 mm²


Stripping capacitiesØ mm

Types of cables

g

16 80 125 SB 040828 125 8.0 - 13.0 round cable, e.g.: 3 x 1.5 mm² up to 5 x 2.5 mm² 71

16 85 125 SB 060444 125 8.0 - 13.0 round cable, e.g.: 3 x 1.5 mm² up to 5 x 2.5 mm² 67

38

GRIPPING PLIERS

20Flat Nose Pliers DIN ISO 5745

20 01 160

20 02 160

20 05 160

20 06 160

flat, short, wide jaws knurled gripping surfaces Chrome vanadium electric steel, forged, oil-hardened

DimensionsArticle No. EAN

4003773- mm

Pliers Head Handles L3mm

W3mm

T1mm g

20 01 125 014447 125


27.0 14.5 8.0 75

20 01 140 014454 140 28.0 15.5 9.5 107

20 01 160 015017 160 30.0 17.0 9.5 144

20 01 180 015666 180 35.0 19.0 10.0 188

20 01 200 015673 200 38.0 21.0 12.0 268


28.0 15.5 9.5 137

20 02 160 035008 160 30.0 17.0 9.5 172

20 05 140 042464 140 chrome plated with multi-component grips

28.0 15.5 9.5 136

20 05 160 042457 160 30.0 17.0 9.5 176

20 06 160 033783 160 chrome plated insulated with multi-component grips, VDE-tested

30.0 17.0 9.5 176

19Round Nose Pliers with cutting edge (Jewellers‘ Pliers)

DIN ISO 5743

19 01 130

for gripping and manipulating fine wires, e.g. in jewellery work ideal for cutting and bending activities, also in electronics for bending wire loops precision-ground round jaws with fine, pointed tips cutting edges additionally in-duction hardened, cutting edge hardness approx. ca. 60 HRC Vanadium electric steel; forged, oil-hardened

Dimensions Cutting capacitiesArticle No. EAN

4003773- mm

Pliers Head Handles D1mm

L3mm

T1mm

W3mm

W4mm Ø mm Ø mm g


polished plastic coated 1.0 32.0 8.0 13.5 2.0 2.2 1.6 73

19 03 130 014348 130 chrome plated plastic coated 1.0 32.0 8.0 13.5 2.0 2.2 1.6 72

39

GRIPPING PLIERS

22Round Nose Pliers DIN ISO 5745

22 01 160

22 02 160

22 05 160

22 06 160

for bending wire loops round, short jaws; finely ground Chrome vanadium electric steel, forged, oil-hardened


4003773- mm


W3mm

D1mm

T1mm g

22 01 125 014461 125


27.0 14.5 2.0 8.0 75

22 01 140 013013 140 28.0 16.5 2.5 9.5 100

22 01 160 015024 160 30.0 18.0 3.0 9.5 140

22 01 180 015819 180 35.0 21.0 3.5 10.5 177


28.0 16.5 2.5 9.5 129

22 02 160 023173 160 30.0 18.0 3.0 9.5 170


28.0 16.5 2.5 9.5 127

22 05 160 042907 160 30.0 18.0 3.0 9.5 169

22 06 160 033790 160 chrome plated insulated with multi-component grips, VDE-tested

30.0 18.0 3.0 9.5 175

22 07 160 015901 160 chrome platedwith plastic dipped insulation, VDE-tested

30.0 18.0 3.0 9.5 196

23Flat Nose Pliers with cutting edges (precision mechanics pliers)

DIN ISO 5745

23 01 140

suitable for gripping and cutting work in fine mechanics flat, long jaws, tapering cutting edges additionally in-duction hardened, cutting edge hardness approx. 60 HRC High-grade special tool steel, forged, oil-hardened

Cutting capacities DimensionsArticle No. EAN

4003773- mm

Head Handles

Ø mm Ø mm

T1mm

L3mm

W3mm

W4mm

T2mm g

23 01 140 041290 140 polished plastic coated 2.5 1.6 7.0 35.0 12.5 3.0 4.5 75

40

GRIPPING PLIERS

25Snipe Nose Side Cutting Pliers (Radio Pliers)

DIN ISO 5745

25 01 160

25 02 160

25 06 160

25 26 160

40°

suitable for finer gripping and cutting work pointed, half-round jaws knurled gripping surfaces with cutting edges for soft, medium-hard and hard wire cutting edges additionally induction hardened, cutting edge hardness approx. 61 HRC Vanadium electric steel; forged, oil-hardened


4003773- mm

Pliers Head Handles

Ø mm Ø mm

L3mm

L4mm

W3mm

T1mm

W4mm

T2mm g

25 01 125 015932 125

black atramentized


2.2 1.6 27.0 13.0 7.0 2.5 1.8 73

25 01 140 013082 140 2.5 1.6 42.0 15.0 8.0 2.5 2.0 89

25 01 160 013099 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 113

25 02 140 023159 140

black atramentized

polished with multi-component grips

2.5 1.6 42.0 15.0 8.0 2.5 2.0 109

25 02 160 023166 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 144

25 03 125 043065 125 chrome plated plastic coated

2.2 1.6 27.0 13.0 7.0 2.5 1.8 72

25 03 160 014492 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 116

25 05 140 035015 140 chrome plated

with multi-component grips

2.5 1.6 42.0 15.0 8.0 2.5 2.0 111

25 05 160 022817 160 2.5 1.6 50.0 16.5 9.0 3.0 2.5 144

25 06 160 033806 160

chrome plated


2.5 1.6 50.0 16.5 9.0 3.0 2.5 146

25 21 160 015994 160 40°

black atramentized

polished plastic coated 2.5 1.6 50.0 23.0 16.5 9.0 3.0 2.5 112

25 25 160 016007 16040° chrome plated


2.5 1.6 50.0 23.0 16.5 9.0 3.0 2.5 143

25 26 160 052111 160

40° chrome plated


2.5 1.6 50.0 23.0 16.5 9.0 3.0 2.5 144

41

GRIPPING PLIERS

26Snipe Nose Side Cutting Pliers (Stork Beak Pliers)

DIN ISO 5745

26 11 200

26 15 200

26 22 20040°

26 26 200

40°

distortion-tolerant, elastic precision tips half-round, long, pointed jaws with cutting edges (hardness approx. 61 HRC) for soft, medium-hard and hard wire Vanadium electric steel; forged, oil-hardened


4003773- mm

Pliers Head Handles

Ø mm Ø mm

L3mm

L4mm

T1mm

W3mm

W4mm

T2mm g


polished plastic coated 3.2 2.2 73.0 9.5 17.5 3.0 2.5 170


polished with multi-com-ponent grips

3.2 2.2 73.0 9.5 17.5 3.0 2.5 201

26 13 200 040590 200 chrome plated plastic coated 3.2 2.2 73.0 9.5 17.5 3.0 2.5 169

26 15 200 035022 200 chrome plated with multi-com-ponent grips

3.2 2.2 73.0 9.5 17.5 3.0 2.5 198

26 16 200 022831 200


3.2 2.2 73.0 9.5 17.5 3.0 2.5 206

26 17 200 016069 200

chrome plated with plastic dipped insulation, VDE-tested

3.2 2.2 73.0 9.5 17.5 3.0 2.5 212

26 21 200 022848 200 40° black atramentized

polished plastic coated 3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 171

26 22 200 023135 200 40° black atramentized


3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 197

26 23 200 016076 200 40° chrome plated plastic coated 3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 171

26 25 200 035039 200 40° chrome plated with multi-com-ponent grips

3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 199

26 26 200 022855 200 40°


3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 204

26 27 200 016090 200 40°

chrome plated with plastic dipped insulation, VDE-tested

3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 220

Elastic tips: dimensionally stable even when twisted

42

GRIPPING PLIERS

27Snipe Nose Pliers with centre cutter (Telephone Pliers)

DIN ISO 5743

27 01 160

for gripping and separating of single wires in harnesseswith centre cutter for soft wire half-round jaws knurled gripping surfaces Chrome vanadium electric steel, forged, oil-hardened


4003773- mm

Head Handles L3mm

W3mm

T1mm

W4mm

T2mm g

27 01 160 016106 160 polished plastic coated 47.0 16.5 9.5 3.0 2.0 120

28Assembly Pliers DIN ISO 5743

28 01 200

28 21 200

specially suitable for gripping and assembly work with a higher prehensile power knurled gripping surfaces High-grade special tool steel, forged, oil-hardened


4003773- mm


W3mm

T1mm

W4mm

T2mm g

28 01 200 044468 200 black atramentized polished plastic coated 33.0 13.5 10.5 4.0 10.5 197


43

GRIPPING PLIERS

29Telephone Pliers DIN ISO 5745

29 11 160

29 25 160

gripping surfaces cross-hatched, knurled Chrome vanadium electric steel, forged, oil-hardened

Style 2extra slim, fine tips; also suitable for soldering work


4003773- mm

Style Pliers Head Handles L3mm

W3mm

T1mm

W4mm

T2mm g

29 11 160 016175 160 1 black atramentized polished plastic coated 55.0 14.0 8.0 2.5 8.5 103


29 25 160 043478 160 2 chrome platedwith multi-component grips

54.0 14.0 9.0 2.0 2.0 139

31Gripping Pliers (Needle-Nose Pliers)

DIN ISO 5743

31 11 160

31 25 16045°

precision pliers for very exact assembly, bending and adjusting work with extra long jaws: length of jaws 55.0 mm smooth ground gripping surfaces edges carefully deburred Chrome vanadium electric steel, forged, oil-hardened


4003773- mm


L4mm

W3mm

T1mm

W4mm

T2mm g


31 15 160 016465 160 chrome plated with multi-component grips 55.0 16.0 7.5 2.0 2.5 124

31 21 160 046790 160 45° black atramentized polished plastic coated 55.0 27.0 16.0 7.5 2.0 2.5 97

31 25 160 016489 160 45° chrome plated with multi-component grips 55.0 27.0 16.0 7.5 2.0 2.5 123

44

GRIPPING PLIERS

30Long Nose Pliers DIN ISO 5745

30 11 160

30 25 160

30 36 160

heavy-duty and hard-wearing gripping pliers different jaw styles Chrome vanadium electric steel, forged, oil-hardened

Style 1long, trapezoidal jaws; knurled gripping surfaces

Style 2long, half-round jaws; knurled gripping surfaces

Style 3long, round jaws; smooth gripping surfaces


4003773- mm


W3mm

T1mm

W4mm

T2mm g

30 11 140 033936 140

1 black atramentized polished plastic coated

42.0 15.0 8.0 2.5 4.0 86

30 11 160 023128 160 46.5 16.5 9.5 3.0 5.0 121

30 11 190 013051 190 50.0 18.5 9.5 3.0 7.0 140

30 13 140 016298 140 1 chrome plated plastic coated

42.0 15.0 8.0 2.5 4.0 87

30 13 160 043485 160 46.5 16.5 9.5 3.0 5.0 118

30 15 140 042914 140

1 chrome platedwith multi-component grips

42.0 15.0 8.0 2.5 4.0 106

30 15 160 035046 160 46.5 16.5 9.5 3.0 5.0 149

30 15 190 001881 190 50.0 18.5 8.0 3.0 7.0 171

30 16 160 001904 160

1 chrome plated insulated with multi-component grips, VDE-tested

46.5 16.5 9.5 3.0 5.0 150

30 21 140 042433 140


42.0 15.0 8.0 2.5 2.0 95

30 21 160 035053 160 50.0 16.5 9.5 3.0 2.5 121

30 21 190 016366 190 50.0 18.5 8.0 3.0 2.4 135

30 23 140 016373 140 2 chrome plated plastic coated 42.0 15.0 8.0 2.5 2.0 95

30 25 140 001980 140

2 chrome platedwith multi-component grips

42.0 15.0 8.0 2.5 2.0 114

30 25 160 035060 160 50.0 16.5 9.5 3.0 2.5 151

30 25 190 043515 190 50.0 18.5 8.0 3.0 2.4 168

30 31 140 042426 140 3 black atramentized polished plastic coated

37.5 15.0 8.0 4.0 2.0 82

30 31 160 035077 160 41.0 16.5 9.5 5.0 2.5 110


30 35 140 043102 140 3 chrome plated


37.5 15.0 8.0 4.0 2.0 102

30 35 160 035084 160 41.0 16.5 9.5 5.0 2.5 138

30 36 160 002123 160

3 chrome platedinsulated with multi-component grips, VDE-tested

41.0 16.5 9.5 5.0 2.5 141

45

GRIPPING PLIERS

32Relay Adjusting Pliers DIN 5235

32 11 135

32 21 135

30 41 160

for gripping components and wires of the smallest diameters and for bending contact and relay springs polished gripping surfaces edges carefully deburred Chrome vanadium electric steel, forged, oil-hardened

for the installation of wedge base bulbs gripping surfaces plastic coated Chrome vanadium electric steel, forged, oil-hardened


4003773- mm


W3mm

T1mm

W4mm

T2mm g



32 23 135 042921 135 chrome plated plastic coated 34.0 12.5 7.0 1.4 3.5 73

32 31 135 043560 135 40° black atramentized polished plastic coated 32.0 12.5 7.0 1.4 3.5 73


Pliers Head Handles

g

30 41 160 048480 160 black atramentized polished plastic coated 120

3041 Halogen Bulb Exchange Pliers

33Duckbill Pliers DIN ISO 5743

33 01 160

duckbill shaped jaws 9 mm wide at the tip and tapering to 1.5 mm thickness smooth gripping surfaces Chrome vanadium electric steel, forged, oil-hardened


4003773- mm


W3mm

T1mm

W4mm

T2mm g


33 03 160 016670 160 chrome plated plastic coated 55.0 15.0 7.5 3.0 9.0 103

32 31 135

40°

46

GRIPPING PLIERS

34Precision Electronics Gripping Pliers DIN ISO 9655

34 12 130

34 22 130

34 32 130

The subtle differenceKNIPEX precision electronics pliers are made of high-quality ball bearing steel and processed with the highest degree of care. Each opening movement is gentle and even without backlash. Each work step proceeds reliably and precisely. This makes work much easier for professionals.

for very precise assembly work, e.g. in electronics and fine mechanics for gripping, holding and bending smoothly ground gripping surfaces, edges finely rounded approx. 20 % lighter than conventional electronics pliers bolted joint and carefully manufactured joint surfaces for even, low-friction movement throughout the entire opening range smooth-running double spring for a gentle and even opening ergonomically optimised multi-component handlesforged from chrome vanadium ball-bearing steel

Style 1flat, wide jaws

Style 2half-round jaws

Style 3round, pointed jaws


4003773- mm

Style Pliers Head Handles Bmm

Amm

Dmm

Emm

Fmm g

34 12 130 061458 135 1 burnished polishedwith multi-com-ponent grips

21.9 11.2 6.5 1.4 3.5 61

34 22 130 061472 135 2 burnished polished with multi-com-ponent grips

22.7 11.2 6.5 1.6 1.6 61

34 32 130 061496 135 3 burnished polishedwith multi-com-ponent grips

23.7 11.2 6.5 2.0 1.0 59

Pliers Sets,

see page 197

47

GRIPPING PLIERS

34Precision Electronics Gripping Pliers ESD DIN ISO 9655

34 12 130 ESD

34 22 130 ESD

34 32 130 ESD

ESD pliers (electrostatic discharge)electrostatic energy is discharged through the handles in a gradual and controlled mannerwhich protects components endangered by electrostatic dischargein accordance with applicable standards, e.g. IEC TR 61 340-5, DIN EN 61 340-5, SP Method 2472

for very precise assembly work, e.g. in electronics and fine mechanics for gripping, holding and bending electrically discharging handles – dissipative smoothly ground gripping surfaces, edges finely rounded approx. 20 % lighter than conventional electronics pliers bolted joint and carefully manufactured joint surfaces for even, low-friction movement throughout the entire opening range smooth-running double spring for a gentle and even opening ergonomically optimised multi-component handlesforged from chrome vanadium ball-bearing steel



Style 3round, pointed jaws


4003773- mm


Amm

Dmm

Emm

Fmm g

34 12 130 ESD 061632 135

1 burnished polishedwith multi-component grips

21.9 11.2 6.5 1.4 3.5 62

34 22 130 ESD 061656 135

2 burnished polished with multi-component grips

22.7 11.2 6.5 1.6 1.6 65

34 32 130 ESD 061670 135 3 burnished polishedwith multi-component grips

23.7 11.2 6.5 2.0 1.0 62

Pliers Sets,

see page 197

48

GRIPPING PLIERS

35Electronics Pliers DIN ISO 9655

35 11 115

35 22 115

35 32 115

35 42 115

45°

35 52 145

precision pliers for fine assembly work, e.g. in electronics and fine mechanics for gripping, holding and bending sturdy, zero backlash box joint smooth ground gripping surfaces edges carefully deburred low-friction double spring for gentle and even opening the polish or mirror polish (only finish 2) together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools Special tool steel, forged, oil-hardened

35 62 145

35 72 145

35 82 145

45°


4003773- mm

Head Handles Bmm

Amm

Dmm

Emm

Fmm g


35 12 115 035107 115 mirror polished with multi-component grips 22.5 9.5 6.5 2.0 4.0 72





35 42 115 040736 115 45° mirror polished with multi-component grips 22.5 9.5 6.5 2.0 1.5 74




35 82 145 039396 145 45° mirror polished with multi-component grips 35.0 12.0 7.5 2.5 1.0 102

Pliers Sets,

see page 197

49

GRIPPING PLIERS

35Electronics Pliers ESD DIN ISO 9655

35 12 115 ESD

35 22 115 ESD

35 32 115 ESD

35 42 115 ESD

45°


precision pliers for fine assembly work, e.g. in electronics and fine mechanics for gripping, holding and bending electrically discharging handles – dissipative sturdy, zero backlash box joint smooth ground gripping surfaces edges carefully deburred low-friction double spring for gentle and even opening the mirror polish together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools with two-colour dual component handles, black/grey Special tool steel, forged, oil-hardened


4003773- mm

Head Handles Bmm

Amm

Dmm

Emm

Fmm g

35 12 115 ESD 024835 115 mirror polished with multi-component grips 22.5 9.5 6.5 2.0 4.0 74



35 42 115 ESD 024866 115 45° mirror polished with multi-component grips 22.5 9.5 6.5 2.0 1.5 74

Pliers Sets,

see page 197

50

GRIPPING PLIERS

36Electronics Mounting Pliers DIN ISO 5743

36 12 130

36 22 125

36 32 125

precision pliers for very fine assembly and repair work in electronics for bending and cutting off wire ends on components sturdy, zero backlash box joint smooth ground gripping surfaces edges carefully deburred low-friction double spring for gentle and even opening the mirror polish together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools High-grade special tool steel, forged, oil-hardened

36 12 130to bend wire in shape for the distance to the board


4003773- mm

Head Handles

Ø mm

L3mm

Wmm

T1mm

W1mm

T2mm g


36 22 125 046967 125 mirror polished with multi-component grips 1.2 18.0 11.5 7.5 7.5 2.6 94

36 32 125 016885 125 mirror polished with multi-component grips 1.0 18.0 11.5 7.5 7.5 4.0 108

36 22 125to bend and cut wire at 1.6 mm length below the board

36 32 125to crunch and cut wire at 1.6 mm length below the board

51

GRIPPING PLIERS

37Gripping Pliers for precision mechanics

DIN ISO 9655

37 11 125

37 21 125

37 31 125

37 41 125

precision pliers for fine assembly work, e.g. in electronics and fine mechanics for gripping, holding, bending and adjusting tips precision ground smooth gripping surfaces edges carefully deburred lap joint Chrome vanadium electric steel, forged, oil-hardened


Style 2flat, concave and pointed jaws


Style 4round, pointed jaws to bend wire loops


4003773- mm


Amm

Dmm

Emm

Fmm g









53

GRIPPING PLIERS

38Mechanics‘ Pliers DIN ISO 5745

38 11 200

38 15 200

38 21 20040°

38 31 200

38 41 190

38 71 20070°

38 91 20045°

high bending strength of the pliers jaws/tips gripping surfaces cross-hatched, knurled Vanadium electric steel; forged, oil-hardened

Style 770° angled, half-round jaws, suitable for pulling split pins; for gripping at points that are difficult to access.

Style 945° angled, half-round, long jaws, also suitable for gripping spark plugs and round components (spark plug cover ”grabber“)


4003773- mm


W3mm

T1mm

W4mm

T2mm g


38 15 200 039594 200 1 chrome plated with multi-component grips 73.0 17.5 9.5 3.0 2.5 209

38 21 200 035176 200 40° 2 black atramentized polished plastic coated 73.0 17.5 9.5 3.0 2.5 175

38 25 200 043669 200 40° 2 chrome plated with multi-component grips 73.0 17.5 9.5 3.0 2.5 209





38 71 200 017202 200 70° 7 black atramentized polished plastic coated 73.0 17.5 9.5 3.0 2.0 174

38 91 200 017219 200 45° 9 black atramentized polished plastic coated 73.0 17.5 9.5 2.5 177

38 95 200 017233 200 45° 9 chrome plated with multi-component grips 73.0 17.5 9.5 2.5 207

54

GRIP PLIERS

40Universal Grip Pliers

40 04 250

hold round, profile and flat material securely heavy duty model with adjustment screw and release lever one-hand operation high clamping pressure due to toggle lever action Pliers body: rolled steel, high-strengthGripping jaws: chrome vanadium electric steel, forged

Article No. EAN4003773- mm mm mm mm g

40 04 180 022190 180 35 25 32 310

40 04 250 002710 250 35 30 32 521

41Grip Pliers

41 04 250

41 14 250

41 24 225

41 34 165

hold round, profile and flat material securely heavy duty model with adjustment screw and release lever one-hand operation high clamping pressure due to toggle lever action Pliers body: rolled steel, high-strength Gripping jaws: chrome vanadium electric steel, forged

Style 0jaws for round workpieces, with wire cutter


Style Pliers

mm mm mm g

41 04 180 002741 180

0 nickel plated

30 20 30 363

41 04 250 002758 250 40 20 30 517

41 04 300 022183 300 65 30 34 923

41 14 250 023470 250 1 nickel plated 36 36 36 557

41 24 225 023487 225 2 nickel plated 25 16 30 504

41 34 165 047858 165 3 nickel plated 20 10 24 189

Style 1jaws with double prism for round, section and flat material

Style 2straight jaws for flat material

Style 3Long-Nose Grip Pliers, narrow, long jaws

55

GRIP PLIERS

42Welding Grip Pliers

42 14 280

42 24 280

42 34 280

for gripping, clamping and holding of diverse profiles heavy duty model with adjustment screw and release lever one-hand operation high clamping pressure due to toggle lever action Pliers body: rolled steel, high-strength

42 14 280heat resistant malleable cast iron jaws; section or flat material items lying side by side are held in place during welding; also for section material with vertical webs up to 25 mm height


Pliers

mm mm g

42 14 280 022206 280 nickel plated 30-65 50 917

42 24 280 022213 280 nickel plated 10-70 850

42 34 280 022220 280 nickel plated 90 692

42 24 280heat resistant malleable cast iron jaws; round or tubular material items lying centrally side by side are held securely during welding

42 34 280gripping jaws of chrome vanadium steel, drop forged; clamps cumbersome workpieces and sections with high webs up to 40 mm

56

CIRCLIP PLIERS

44Circlip Pliers to assemble internal circlips into bores

44 11 J2

44 21 J21

90°

44 31 J22

45°

for fitting circlips into bores, range of application from 8 - 140 mm dia. solid style, forged non-slip, solid tips Pliers body and tips: chrome vanadium steel, forged, oil-hardened

Style 1DIN 5256 C, straight tips

Style 2DIN 5254 B; 90° angled tips

Style 345° angled tips

Pliers Sets,

see page 193

Size of boreØ mm


Style Pliers Head Handles

g

44 11 J0 040286 140


8 - 13 88

44 11 J1 022862 140 12 - 25 88

44 11 J2 022879 180 19 - 60 135

44 11 J3 033943 225 40 - 100 196

44 11 J4 042549 320 85 - 140 469

44 13 J0 048176 140

1 chrome plated plastic coated

8 - 13 89

44 13 J1 042938 140 12 - 25 88

44 13 J2 042945 180 19 - 60 138

44 13 J3 042952 225 40 - 100 194

44 13 J4 017301 320 85 - 140 463

44 21 J01 040132 130

90° 2 black atramentized polished plastic coated

8 - 13 88

44 21 J11 022886 130 12 - 25 88

44 21 J21 022893 170 19 - 60 139

44 21 J31 033769 215 40 - 100 196

44 21 J41 043683 300 85 - 140 462

44 23 J01 017325 140

90° 2 chrome plated plastic coated

8 - 13 87

44 23 J11 042969 130 12 - 25 89

44 23 J21 042976 170 19 - 60 138

44 23 J31 042983 215 40 - 100 200

44 31 J02 066941 140


8 - 13 90

44 31 J12 066958 140 12 - 25 90

44 31 J22 066965 180 19 - 60 140

44 31 J32 066972 225 40 - 100 195

44 31 J42 066989 310 85 - 140 465

57

CIRCLIP PLIERS

46Circlip Pliers to assemble external circlips on shafts

46 11 A2

46 21 A21

90°

46 31 A22

45°

for fitting circlips on shafts, range of application from 3 - 140 mm dia. solid style, forged non-slip, solid tips Pliers body and tips: chrome vanadium steel, forged, oil-hardened

Style 1DIN 5254 A; straight tips


Style 345° angled tips

Pliers Sets,

see page 193

Size of shaftØ mm



g

46 11 A0 033950 140


3 - 10 85

46 11 A1 022909 140 10 - 25 86

46 11 A2 022916 180 19 - 60 134

46 11 A3 033974 210 40 - 100 220

46 11 A4 042532 320 85 - 140 505

46 13 A0 017417 140

1 chrome plated plastic coated

3 - 10 85

46 13 A1 042990 140 10 - 25 82

46 13 A2 043003 180 19 - 60 133

46 13 A3 043010 210 40 - 100 211

46 21 A01 033967 125


3 - 10 85

46 21 A11 023005 125 10 - 25 85

46 21 A21 022923 170 19 - 60 132

46 21 A31 033981 200 40 - 100 219

46 21 A41 039365 300 85 - 140 510

46 23 A01 017509 125

90° 2 chrome plated plastic coated

3 - 10 84

46 23 A11 043027 125 10 - 25 84

46 23 A21 043034 170 19 - 60 132

46 23 A31 043041 200 40 - 100 221

46 31 A02 066996 130


3 - 10 83

46 31 A12 067009 130 10 - 25 85

46 31 A22 067016 185 19 - 60 133

46 31 A32 067023 210 40 - 100 213

46 31 A42 067030 310 85 - 140 511

58

CIRCLIP PLIERS

44Circlip Pliers for large internal circlips

44 10 J6

for assembling circlips into bores within the range of Ø 122 - 400 mm with locking device, can be released with replaceable tips made of tempered steel black powder coated Pliers body: rolled steel, high-strength Tips: special tool steel, oil-hardened



Size of boreØ mm


Style Pliers

g

44 10 J5 024910 570 1 black powder-coated

122 - 300 1738

44 10 J6 024927 580 252 - 400 1755

44 20 J51 024958 590 90° 2 black powder-coated

122 - 300 1803

44 20 J61 024965 600 252 - 400 1723

44 19 J5 024934 1 pair of spare tips for 44 10 J5




45Special Retaining Ring Pliers for retaining rings on shafts

DIN ISO 5743

45 10 170

45 21 200

30°

for fitting horseshoe-shaped spring retaining rings and circlips without grip holes for shaft retaining devices with opening spring Chrome vanadium electric steel, forged, oil-hardened

45 10 170for retaining rings with a minimum ring split gap of 3.6 mm

45 21 200anlged jaws with centering hole; for snap rings larger than 12.0 mm dia., e.g. for securing cardan shafts in a motor vehicle; minimum ring split gap of the rings 2.2 mm

45 10 170 45 21 200 45 21 200


Pliers Handles

g

45 10 170 017370 170 burnished 156

45 21 200 031208 200 30° burnished plastic coated 186

59

CIRCLIP PLIERS

46Circlip Pliers for large external circlips

46 10 A5

for assembling circlips on shafts within the range of Ø 122 - 400 mm with locking device, can be released with replaceable tips made of tempered steel black powder coated Pliers body: rolled steel, high-strength Tips: special tool steel, oil-hardened

Style 1DIN 5254 A; straight tips


Size of shaftØ mm


Style Pliers

g

46 10 A5 024996 560 1 black powder-coated

122 - 300 1773

46 10 A6 025009 570 252 - 400 1795

46 20 A51 025023 570 90° 2 black powder-coated

122 - 300 1832

46 20 A61 025030 580 252 - 400 1826

46 19 A5 024316 1 pair of spare tips for 46 10 A5




46Circlip Pliers for grip rings on shafts

DIN ISO 5743

46 11 G0

46 11 G2

for fitting grip rings on shafts from 1.5 - 30 mm dia. with opening spring solid style, forged non-slip, solid tips Pliers body and tips: chrome vanadium steel, forged, oil-hardened

46 11 G0for rings of 1.5 - 4.0 mm dia., with adjustable stop screw to prevent overstretching

Size of shaftØ mm


Pliers Head Handles

g

46 11 G0 047896 140 black atramentized polished plastic coated 1.5 - 4.0 87

46 11 G1 031062 140


4.0 - 7.0 85

46 11 G2 031079 140 5.0 - 13.0 85

46 11 G3 031086 140 14.0 - 18.0 86

46 11 G4 031093 180 20.0 - 30.0 134

60

CIRCLIP PLIERS

48

48 11 J2

48 21 J21

90°

Tiptop qualityEasy and reliable assembly: form-fitting inserted and pressed-in tips made of high-density spring steel offer a high level added resilience against excessive stress and strain, e.g. when removing stuck rings. The large supporting surfaces and the position of the tips make it more difficult for the rings to bounce off.

Precision and durability

High-density spring steel with a score-free surface is used for the tips. This increases the tips‘ resistance to dynamic and static strain. The tips are 30 % more stable than conventional pliers when subjected to one-off overloading while still allowing good accessibility during assembly. Subjected to dynamic strain, the tips‘ resistance capacity is up to 10 times greater! The tips on the precision circlip pliers are non-detachable!


Style 2DIN 5256 D; 90° angled tips

Sturdy, inserted tips: made from high-density spring steel

Slim head shape

Pliers Sets,

see page 193

Tight fit through compression

Size of boreØ mm


Style Pliers Handles Tips Ømm g

48 11 J0 048510 140

1 grey atramentized with non-slip plastic coating

8 - 13 0.90 105

48 11 J1 048527 140 12 - 25 1.25 105

48 11 J2 048534 180 19 - 60 1.80 175

48 11 J3 048541 225 40 - 100 2.25 266

48 11 J4 048558 320 85 - 140 3.20 580

48 21 J01 048619 130

90° 2 grey atramentized with non-slip plastic coating

8 - 13 0.90 105

48 21 J11 048633 130 12 - 25 1.25 105

48 21 J21 048640 165 19 - 60 1.80 175

48 21 J31 048657 210 40 - 100 2.25 265

48 21 J41 048664 305 85 - 140 3.20 576

Precision Circlip Pliers to assemble internal circlips into bores

heavy duty in continuous operation: up to 10 times longer service life compared to turned tips joint with screw: precise, zero backlash operation of pliers non-slip plastic coating on the handles Pliers body: chrome vanadium electric steel, forged, oil-hardened Inserted tips: spring steel wire, drawn

With inserted tips for reliable work

61

Bolted joint: high precision and smooth action

49 21 A21

90°

49 11 A2

Spring inside the joint: the spring is protected inside the precisely bolted joint. It does not hinder work and cannot get dirty or lost.

KNIPEX Precision Circlip Pliers: fit circlips without distortion; easy and quick assembling

Conventional Circlip Pliers: distortion of the circlip when widening the circlip

Circlips are held reliably: large contact areas and the position of the tips make it difficult for the circlip to bounce off

Style 3 / style 4: with adjustable opening restriction

Size of shaftØ mm


Style Pliers Handles Tips Ømm g

49 11 A0 048718 140

1 grey atramentizedwith non-slip plastic coating

3 - 10 0.90 101

49 11 A1 048725 140 10 - 25 1.25 100

49 11 A2 048732 180 19 - 60 1.80 170

49 11 A3 048749 225 40 - 100 2.25 270

49 11 A4 048756 320 85 - 140 3.20 599

49 21 A01 048817 130

90° 2 grey atramentized with non-slip plastic coating

3 - 10 0.90 100

49 21 A11 048824 130 10 - 25 1.25 102

49 21 A21 048831 165 19 - 60 1.80 169

49 21 A31 048848 210 40 - 100 2.25 272

49 21 A41 048855 305 85 - 140 3.20 601

49 31 A0 061748 140 3 grey atramentizedwith non-slip plastic coating

3 - 10 0.90 103

49 41 A01 061755 130 90° 4 grey atramentized with non-slip plastic coating

3 - 10 0.90 102

heavy duty in continuous operation: up to 10 times longer service life compared to turned tips large contact faces on the tips: no distortion of circlips, easy fitting joint with screw: precise, zero backlash operation of pliers internal opening spring, protected and captive non-slip plastic coating on the handles Pliers body: chrome vanadium electric steel, forged, oil-hardened Inserted tips: spring steel wire, drawn

Precision Circlip Pliers to assemble external circlips on shafts

CIRCLIP PLIERS

49

49 31 A0 / Style 3with additional opening limiter (infinitely adjustable opening width); avoids overstretching of small external circlips; DIN 5254 A; straight tips

Pliers Sets,

see page 193

Style 1DIN 5254 A, straight tips


49 41 A01 / Style 4with additional opening limiter (infinitely adjustable opening width); avoids overstretching of small external circlips; DIN 5254 B; 90° angled tips

With inserted tips for reliable work

62

CARPENTERS‘ PINCERS

50Carpenters‘ Pincers DIN ISO 9243

50 00 210

50 01 225

for heaviest duty specially favoured by craftsmen for their precise workmanship extreme wear resistance and well balanced cutting edges additionally hardened; cutting edge hardness approx. 60 HRC Special tool steel, forged, oil-hardened


4003773- mm

Pliers Head Handles

Ø mm g

50 00 130 014423 130


1,6 135

50 00 160 013129 160 1,8 215

50 00 180 013136 180 2,0 303

50 00 210 013143 210 2,2 398

50 00 225 013150 225 2,2 427

50 00 250 013167 250 2,2 563

50 00 300 015710 300 2,4 862

50 01 130 015789 130


1,6 141

50 01 160 015802 160 1,8 223

50 01 180 016021 180 2,0 316

50 01 210 016052 210 2,2 411

50 01 225 016083 225 2,2 437

50 01 250 016267 250 2,2 583

50 01 300 016915 300 2,4 903

51Hammerhead Style Carpenters‘ Pincers DIN ISO 9243

51 01 210

with striking face for driving in nails cutting edges additionally hardened; cutting edge hardness approx. 60 HRC Special tool steel, forged, oil-hardened

Multi-functional: driving in and pulling nails


Pliers Head Handles

g

51 01 210 023104 210 black atramentized polished plastic coated 413

63

CARPENTERS‘ PINCERS

55Farriers‘ Pincers (Tear-off Pliers for vehicle bodywork)

DIN ISO 5743

55 00 300

the ideal pliers for the farrier with small head and anvil for redirecting horseshoe-nailsalso suitable for dismantling work in vehicle body workshops cutting edges additionally hardened; cutting edge hardness approx. 59 HRC Special tool steel, forged, oil-hardened


Pliers Head Head widthmm g

55 00 300 014072 300 black atramentized polished 20,0 786

57Unsoling Pincer for horseshoes DIN ISO 5743

57 00 360

for the farrier also suitable for dismantling work in vehicle body workshops also for dismantling work on timber and metal cutting edges additionally hardened; cutting edge hardness approx. 59 HRC Special tool steel, forged, oil-hardened




58Potters‘ Pincers (Brick Pincers)

DIN ISO 5743

58 30 225

for pottery work with wire cutter for soft wire cutting edges additionally hardened; cutting edge hardness approx. 59 HRC Special tool steel, forged, oil-hardened

58 10 225head width 10 mm

58 30 225head width 20 mm





64

CONCRETORS‘ NIPPERS

990 Concretors‘ Nippers

(Tower Pincers, Steel Fixers‘ Nippers)

DIN ISO 9242

99 00 280

99 04 250

99 01 220

to twist and cut wire in one operation: fast, reliable and economical unobtained precision and long service life make these the bestselling concretors' nippers in the world cutting edges additionally hardened; cutting edge hardness approx. 61 HRC High-grade special tool steel, forged, oil-hardened

99 00 220 K12with 12 mm head, particularly suitable for tile paving work


4003773- mm

Pliers Head Handles

Ø mm Ø mm g

99 00 200 014393 200


1,8 1,4 230

99 00 220 013273 220 2,4 1,6 315

99 00 250 013280 250 2,4 1,6 335

99 00 280 014096 280 2,8 1,8 455

99 00 300 014409 300 3,1 1,8 510

99 00 220 K12 027812 220 black atramentized polished 2,4 1,6 315

99 01 200 021452 200


1,8 1,4 247

99 01 220 021469 220 2,4 1,6 334

99 01 250 021483 250 2,4 1,6 427

99 01 280 021490 280 2,8 1,8 499

99 01 300 014416 300 3,1 1,8 548

99 04 220 048398 220

nickel plated

2,4 1,6 321

99 04 250 048213 250 2,4 1,6 398

99 04 280 048220 280 2,8 1,8 457

65

CONCRETORS‘ NIPPERS

991 High Leverage Concretors‘ Nippers

high lever transmission

DIN ISO 9242

99 10 250

99 10 300

99 11 300

99 14 250

99 14 300

25 % less effort requiredcompared to conventional concretors‘ nippers of the same size.

to lace concrete reinforcing steel with binding wire from a roll wire is twisted and cut in a single pass high-leverage joint, minimising strain, even when thick binding wires are used extra-slim form for tying deep mounted steel rods the high damping of the cutting stroke on cutting through the binding wire reduces the strain on tendons and musclescutting edges additionally hardened; cutting edge hardness approx. 61 HRC High-grade special tool steel, forged, oil-hardened


4003773- mm

Pliers Head Handles

Ø mm Ø mm

Head widthmm g

99 10 250 071396 250 black atramentized polished

3,3 1,8 23,0 350

99 10 300 022398 300 3,8 2,0 25,0 501

99 11 250 071402 250 black atramentized polished plastic coated

3,3 1,8 23,0 350

99 11 300 042365 300 3,8 2,0 25,0 537

99 14 250 071419 250 nickel plated

3,3 1,8 23,0 350

99 14 300 028116 300 3,8 2,0 25,0 499

67

CUTTING PLIERS

61Bolt End Cutting Nippers high lever transmission

DIN ISO 5743

powerful, compact, comfortable

61 01 20085°

61 02 20085°

compared to conventional lever-assisted end cutting nippers, greater cutting capacity, less effort required and better handling for all classes of wire including piano wire exceptional cutting capacity due to high-leverage joint cutting edges additionally induction hardened; cutting edge hardness approx. 64 HRC Vanadium electric steel; forged, oil-hardened

61 02 200with slim two-colour multi-component sleeves without collar for better handling and easier transport; with large contact surface on the handles for better allotment of pressure and more comfort at work

Particularly efficient for fence constructionAlmost flush cutting of bolts, nails etc.

Extraordinary cutting performance: also for piano wire


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm Ø mm g

61 01 200 033172 200 85° black atramentized polished plastic coated 1.0 - 6.0 4.0 3.5 3.0 435

61 02 200 067047 200 85° black atramentized polished with slim multi-component grips 1.0 - 6.0 4.0 3.5 3.0 435

62Electronics Oblique Cutting Nipper DIN ISO 9654

62 12 120

15°

with cutting edges for soft and medium hard wire without bevel, for flush cutting cutting edges additionally induction hardened; cutting edge hardness approx. 58 HRC low-friction double spring for gentle and even opening sturdy, zero backlash box joint the polish together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools


4003773- mm

Head Handles

Ø mm Ø mmA

mmB

mmD

mmC

mm g

62 12 120 048008 120 15° polished with multi-component grips 0.3 - 1.0 0.7 11 10 7.5 17 93

High-grade special tool steel, forged, oil-hardened

68

CUTTING PLIERS

64Electronics End Cutting Nippers DIN ISO 9654

64 02 115

90°

64 12 115

90°

64 22 115

90°

64 32 120

15°

64 42 115

27°

precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics sturdy, zero backlash box joint low-friction double spring for gentle and even opening the polish or mirror polish (only finish 2) together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools cutting edges additionally induction hardened; hardness at least 56 HRC High-grade special tool steel, forged, oil-hardened

Style 0End Cutter, with bevel

64 11 115End Cutter, without bevel

64 12 115End Cutter, with small bevel

Style 2:End Cutter, mini-blade with small bevel

Style 3Oblique End Cutter, short head, with small bevel, α = 15°

Style 4Oblique End Cutter, short head, with small bevel, α=27°

64 22 115 64 22 115

64 01/02/11/12

64 32/42/52

69

CUTTING PLIERS

64 62 120

64 72 120

Style 5Oblique End Cutter, short head, without bevel, for flush cutting, α = 27°

Style 6Oblique End Cutter, mini-blade with small bevel, α = 65°

Style 7Oblique End Cutter, mini-blade with small bevel, head with recess, α = 35°

64 52 115

27°

64 62 120

65°

64 72 120

35°

64 62 120

64 72 120


4003773- mm

Style Head Handles

Ø mm Ø mm Ø mm

Amm

Bmm

Dmm

Cmm g

64 01 115 017745 115 90° 0 polished plastic coated 2.0 1.0 0.6 11.0 6.0 7.5 16.0 76

64 02 115 035343 115 90°

0 mirror polished with multi-component grips 2.0 1.0 0.6 11.0 6.0 7.5 16.0 94

64 11 115 017769 115 90° 1 polished plastic coated 1.4 0.8 11.0 6.0 7.0 16.0 74

64 12 115 040743 115 90°


64 22 115 017806 115 90° 2 mirror polished with multi-component grips 0.8 10.0 20.0 6.0 3.0 65

64 32 120 017820 120 15°


64 42 115 017844 115 27° 4 mirror polished with multi-component grips 1.5 1.0 0.5 10.5 10.0 7.0 12.0 69

64 52 115 040439 115 27°

5 mirror polished with multi-component grips 1.3 10.5 10.0 7.0 12.0 69

64 62 120 046998 120 65° 6 mirror polished with multi-component grips 0.6 9.5 18.5 6.0 5.0 70

64 72 120 017882 120 35°

7 mirror polished with multi-component grips 1.5 12.0 19.5 7.0 5.0 95

Pliers Sets,

see page 197

70

64Electronics End-Cutting Nippers ESD DIN ISO 9654

64 12 115 ESD

90°

64 32 120 ESD

15°

64 62 120 ESD

65°


precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics electrically discharging handles – dissipative strudy, zero backlash box joint low-friction double spring for gentle and even opening the mirror polish together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools cutting edges additionally induction hardened; hardness at least 56 HRC with two-colour dual component handles, black/grey High-grade special tool steel, forged, oil-hardened

Style 1End Cutter, with small bevel

Style 3Oblique End Cutter, short head, with small bevel, a = 15°

Style 6Oblique End Cutter, mini-blade with small bevel, a = 65°

64 62 120 ESD64 12 115 ESD

64 32 120 ESD

Pliers Sets,

see page 197

64 62 120 ESD

Cutting Capacities DimensionsArticle No. EAN

4003773- mm

Style Head Handles

Ø mm Ø mm Ø mmA

mmB

mmD

mmC

mm g

64 12 115 ESD 024323 115 90° 1

mirror polished

with multi-compo-nent grips

2.0 0.8 0.5 11.0 6.0 7.0 16.0 94

64 32 120 ESD 025078 120 15°

3 mirror polished


1.5 1.0 0.5 11.0 10.0 7.0 17.0 92

64 62 120 ESD 025085 120 65° 6

mirror polished


0.6 9.5 18.5 6.0 5.0 70

CUTTING PLIERS

71

CUTTING PLIERS

67High Leverage End Cutting Nippers DIN ISO 5748

67 01 200

with cutting edges for soft, hard and piano wire high cutting capacity with little effort due to optimum coordi-nation of cutting edge angle and transmission ratio cutting edges additionally in-duction hardened, cutting edge hardness approx. 64 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened


4003773- mm

Pliers Head Handles


67 01 140 043690 140


4.0 3.1 2.0 1.5 152

67 01 160 040620 160 4.5 3.4 2.5 2.0 237

67 01 200 040637 200 5.0 3.8 3.0 2.5 318

67 05 140 017929 140

chrome plated with multi-component grips

4.0 3.1 2.0 1.5 176

67 05 160 017936 160 4.5 3.4 2.5 2.0 266

67 05 200 017943 200 5.0 3.8 3.0 2.5 361

68End Cutting Nippers DIN ISO 5748

68 01 180

with cutting edges for soft and hard wire also suitable for twisting and cutting binding wire cutting edges additionally induction hardened, cutting edge hardness approx. 61 HRC High-grade special tool steel, forged, oil-hardened

Also suitable for wire netting in reinforced concrete construction


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm g

68 01 160 013792 160


4.0 2.8 2.3 202

68 01 180 013808 180 4.0 3.2 2.5 284

68 01 200 013815 200 4.0 3.5 2.8 319

69End Cutting Nippers for mechanics

DIN ISO 5748

69 01 130

with cutting edges for soft, hard and piano wire; also suitable for thin copper wires lap joint cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm Ø mmA

mmB

mmD

mmC

mm g

69 01 130 017974 130 black atramentized polished plastic coated 0.4 - 2.0 1.3 1.0 0.8 16 7.5 10 20 111

69 03 130 018001 130 chrome plated plastic coated 0.4 - 2.0 1.3 1.0 0.8 16 7.5 10 20 111

72

CUTTING PLIERS

73

70Diagonal Cutters DIN ISO 5749

70 01 160

70 02 160

70 05 160

70 06 160

the essential cutting tool for versatile use high quality material and precise workmanship for long service life precision cutting edges additionally induction hardened (cutting edge hardness approx. 62 HRC) for soft and hard wire clean cutting of thin copper wires, also at the cutting-edge tips narrow head style for use in confined areas Vanadium electric steel; forged, oil-hardened

Cuts fine wires cleanly along the complete length of the blades

Slim head style and precise cut at blade tips: Advantageous when working in confined areas


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm g

70 01 110 014324 110

black atramentized


3.0 2.0 1.2 80

70 01 125 013402 125 3.0 2.3 1.5 80

70 01 140 013419 140 4.0 2.5 1.8 126

70 01 160 013426 160 4.0 2.8 2.0 171

70 01 180 018070 180 4.0 3.0 2.5 200

70 02 125 034025 125

black atramentized


3.0 2.3 1.5 119

70 02 140 023098 140 4.0 2.5 1.8 150

70 02 160 034032 160 4.0 2.8 2.0 206

70 02 180 034049 180 4.0 3.0 2.5 252

70 04 140 018100 140 chrome plated 4.0 2.5 1.8 114

70 05 125 039501 125


3.0 2.3 1.5 119

70 05 140 039488 140 4.0 2.5 1.8 154

70 05 160 039600 160 4.0 2.8 2.0 207

70 05 180 043706 180 4.0 3.0 2.5 246

70 06 125 018124 125


3.0 2.3 1.5 121

70 06 140 040293 140 4.0 2.5 1.8 160

70 06 160 021995 160 4.0 2.8 2.0 216

70 06 180 033813 180 4.0 3.0 2.5 254

70 07 160 018155 160 chrome plated with dipped insulation, VDE-tested

4.0 2.8 2.0 227

70 07 180 018179 180 4.0 3.0 2.5 269


polished plastic coated 3.0 2.0 1.2 91

70 15 110 029649 110 chrome plated with multi-component grips 3.0 2.0 1.2 98

70 26 160 018223 160 chrome platedinsulated with multi-component grips, VDE-tested

4.0 2.8 1.8 216

CUTTING PLIERS

74

CUTTING PLIERS

71KNIPEX CoBolt® Compact Bolt Cutters

DIN ISO 5743

71 01 200

71 02 200

71 12 200

71 22 20020°

71 41 20020°

60 % less effort required compared to conventional high-leverage diagonal cuttersThe ingenious lever-action mechanism ensures an extremely favourable lever ratio with very little friction. The cutting force is about 20 times higher than the hand force applied.

Clever muscle man

precision cutting edges for soft and hard wire and piano wire cuts components like bolts, nails, rivets, etc. up to 5.2 mm dia. exceptional cutting performance with minimum effort because of unsurpassedly effective lever action design cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened

71 12 200 / 71 22 200 / 71 32 200opening spring and locking device are integrated in the handles also for comfortable work and protected transport

Style 220° angled head with single-sided joint bar and diagonal cutting edge for flush cutting; with space for gripping

Style 3the recess in the blade allows easier cutting of thicker wires, e.g. for anchor bolts in false ceilings

Style 4the recess in the blade allows easier cutting of thicker wires, e.g. for anchor bolts in false ceilings; 20° angled head with single-sided joint bar and diagonal cutting edge for flush cutting; with space for gripping

Opening spring and transport lock

Comparison between 71 0x 200 and 71 2x 200

71 02 200 with slim two-colour multi-component sleeves without collar for better handling and easier transport; with large contact surface on the handles for better allotment of pressure and more comfort at work

DEGREE OF FORCE REQUIRED70 % 100 %

75

Conventional toggle lever assisted side cutter:

max. opening approx. 3.5 mmgreat weight = 600 gdouble toggle lever joint cumbersome

New KNIPEX-Model e.g. 71 31 200 CoBolt®:

weight only 330 ggood handling small size 30 % less effort required

71 31/32/41 200: The cutting edge recess near the joint holds thicker wires in a favourable cutting position (optimum lever ratio). The re-positioning that is usual with bolt cutters is not needed here.


4003773- mm

Style Pliers Handles


71 01 200 033165 200 0 black atramentized plastic coated 6.0 5.2 4.0 3.6 335

71 02 200 047056 200 0 black atramentized with slim multi-component grips 6.0 5.2 4.0 3.6 365


71 21 200 066866 200 20° 2 black atramentized plastic coated 6.0 5.2 4.0 3.6 320

71 22 200 066873 200 20° 2 black atramentized with slim multi-component grips 6.0 5.2 4.0 3.6 375

71 31 200 042327 200 3 black atramentized plastic coated 6.0 5.2 4.0 3.6 330


71 41 200 066897 200 20° 4 black atramentized plastic coated 6.0 5.2 4.0 3.6 335

600 g

330 g

joint axle

hard wire Ø 2 mm

picture not true to scale

CUTTING PLIERS

76

CUTTING PLIERS

7172 Bolt Cutters

cuts hard components up to 48 HRC

71 72 460

71 72 610

71 72 760

71 72 910

cutting capacity up to 48 HRC hardness robust cutting edges are additionally induction hardened, cutting-edge hardness approx. 62 HRC forged-in stopper with comfortable shock-absorber good access due to very flat construction of head and joint area ergonomically angled handles to minimise effort sturdy non-slip two-colour dual component handle sleeves precise adjustment (12 positions) by eccentric bolt high cutting performance with minimum effort due to optimum co-ordination of the cutting edge angle, transmission ratio and ergonomic handle shape bolted cutter head, replaceable Blade: chrome vanadium heavy-duty steel, forged, oil-hardened Joint: special tool steel, forged Handle: steel tube, powder-coated

Forged-in stopper with damping inserts: cushions the cutting stroke comfortably


4003773- mm

Head Handles HRC 19Ø mm

HRC 40Ø mm

HRC 48Ø mm g

71 72 460 066750 460 grey atramentized with multi-component grips 8 6 5 2100




71 79 460 066804 Spare cutter head for 71 72 460 complete with screws




77

CUTTING PLIERS

7182 Concrete Mesh Cutter

71 82 950

cutting capacity up to 48 HRC hardness robust cutting edges additionally induction hardened, cutting-edge hardness approx. 62 HRC forged-in stopper with comfortable shock-absorber good access due to very flat construction of head and joint area ergonomically angled handles to minimise effort sturdy non-slip two-colour dual component handle sleeves precise adjustment (12 positions) by eccentric bolt high cutting performance with minimum effort due to optimum co-ordination of the cutting edge angle, transmission ratio and ergonomic handle shape bolted cutter head, replaceable Blade: chrome vanadium heavy-duty steel, forged, oil-hardened Joint: special tool steel, forged Handle: steel tube, powder-coated

The special shape of the mesh cutter head, 71 82 950, enable it to cut structural steel that is lying down flat.


4003773- mm

Head Handles HRC 19Ø mm

HRC 40Ø mm

HRC 48Ø mm g



78

CUTTING PLIERS

72Diagonal Cutters for plastics DIN ISO 5743

72 01 160

72 02 125

72 11 16045°

72 21 16085°

cutting face flush ground non-bevelled, for separating moulded plastic components from sprues

cuts soft materials such as lead in a flush cutwith opening spring Vanadium electric steel; forged, oil-hardened


Head Handles

g

72 01 140 043713 140


125

72 01 160 041245 160 164

72 01 180 046837 180 193

72 02 125 044215 125 polished with multi-component grips 109

72 11 160 046813 160 45° polished plastic coated 156


KEVLAR® is a registered trademark of E. I. du Pont de Nemours and Company

79

CUTTING PLIERS

7251 Diagonal Cutter for fibre optics

(glass fibre cable)

DIN ISO 5743

72 51 160

■ specially developed for cutting fibre optics (glass fibre cables)�■ cutting face flush ground�■ cutting edges additionally induction hardened�■ with opening spring�■ Vanadium electric steel; forged, oil-hardened

The KEVLAR® fibres in strain relief are cut with the 95 03 160 shears.


Head Handles

g

72 51 160 028031 160 polished plastic coated 166

7491 High Leverage Centre Cutters

DIN ISO 5743

74 91 250

■ with integrated forged axle for heaviest duty�■ with precision cutting edges for soft, hard and piano wire�■ cuts thick wires with less effort than other diagonal cutters

of the same length�■ centric precision cutting edges�■ high cutting performance with minimum effort due to optimum

co-ordination of the cutting edge angle, transmission ratio and ergonomic handle shape�

■ cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC�

■ Chrome vanadium heavy-duty steel, forged, oil-hardened

The cutting edges are in the centre of the cutter head


4003773- mm

Pliers Head Handles


74 91 250 034070 250 black atramentized polished plastic coated 5.0 5.0 3.8 3.5 395

80

CUTTING PLIERS

74High Leverage Diagonal Cutters DIN ISO 5749

74 01 200

74 02 250

74 05 200

74 06 200

74 07 200

74 12 180

74 21 20012°

20 % less effort requiredcompared to conventional diagonal cutters of the same length. With integrated forged joint axle.

for very tough, continuous use high cutting performance with minimum effort due to optimum co-ordination of the cutting edge angle, transmission ratio and ergonomic handle shape precision cutting edges additionally induction hardened (cutting edge hardness approx. 64 HRC) for all sorts of wire including piano wire Chrome vanadium heavy-duty steel, forged, oil-hardened

Style 1with opening spring; to be activated if required

74 12: opening spring in deactivated position

74 12: just gentle sliding with your thumb will activate the opening spring

Style 212° angled head offers clearance for gripping

With integrated forged joint axle for very tough, continuous use

81

CUTTING PLIERS


4003773- mm


Ø mm Ø mm Ø mm g

74 01 140 039747 140


3.1 2.0 1.5 131

74 01 160 033141 160 3.4 2.5 2.0 178

74 01 180 022008 180 3.8 2.7 2.2 241

74 01 200 034056 200 4.2 3.0 2.5 263

74 01 250 034063 250 4.6 3.5 3.0 391

74 02 140 042419 140

0 black atramentized polished with multi-component grips

3.1 2.0 1.5 157

74 02 160 023081 160 3.4 2.5 2.0 209

74 02 180 023074 180 3.8 2.7 2.2 273

74 02 200 040309 200 4.2 3.0 2.5 304

74 02 250 042402 250 4.6 3.5 3.0 437

74 05 140 039617 140

0 chrome plated with multi-component grips

3.1 2.0 1.5 157

74 05 160 022961 160 3.4 2.5 2.0 209

74 05 180 022978 180 3.8 2.7 2.2 270

74 05 200 035367 200 4.2 3.0 2.5 303

74 05 250 039754 250 4.6 3.5 3.0 440

74 06 160 040705 160

0 chrome plated insulated with multi-component grips, VDE-tested

3.4 2.5 2.0 215

74 06 180 022985 180 3.8 2.7 2.2 280

74 06 200 033820 200 4.2 3.0 2.5 308

74 06 250 041955 250 4.6 3.5 3.0 453

74 07 200 018414 200 0 chrome platedwith dipped insulation, VDE-tested

4.2 3.0 2.5 328

74 07 250 018421 250 4.6 3.5 3.0 510

74 12 160 065111 160

1 black atramentized polished with multi-component grips

3.4 2.5 2.0 209

74 12 180 060192 180 3.8 2.7 2.2 273

74 21 160 034322 160


3.4 2.5 2.0 181

74 21 180 069973 180 3.8 2.7 2.2 235

74 21 200 050483 200 4.2 3.0 2.5 258

74 21 250 045021 250 4.6 3.5 3.0 390

74 22 200 051831 200

12° 2 black atramentized polished with multi-component grips

4.2 3.0 2.5 300

74 22 250 071372 250 4.6 3.5 3.0 437

leverage comparison between the diagonal cutter <=> high leverage diagonal cutter

hard wire (dia. 2 mm)

80 % 100 %

joint axle

DEGREE OF FORCE REQUIRED

20 % less hand force required

High transmission of power High Leverage Diagonal Cutter:290 N hand force required to cut hard wire (dia. 2 mm)

Standard transmission of power Diagonal Cutter: 370 N hand force required to cut hard wire (dia. 2 mm)

20 % reduction thanks to high leverage power joint

82

CUTTING PLIERS

75Electronics Diagonal Cutters DIN ISO 9654

75 02 125

75 12 125

75 22 125

75 52 125

bolted joint for high precision and stress tolerance for ultra fine cutting work, e.g. in electronics and fine mechanics with sharp, ground cutting edges for soft and hard wire and piano wire cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC low-friction double spring for gentle and even opening High-grade special tool steel, forged, oil-hardened

Style 0with bevel

Style 1with bevel and lead catcher, no uncontrolled loss of cut wire ends

Style 2with small bevel

Style 5particularly narrow head, with bevel

Bolted joint


4003773- mm

Style Pliers Handles


mmB

mmD

mm g

75 02 125 040491 125 0 burnished with plastic grips 0.2 - 1.3 1.0 0.6 0.4 10.5 14 6.5 81

75 12 125 040514 125

1 burnished with plastic grips 0.2 - 1.3 1.0 0.6 0.4 10.5 14 6.5 80

75 22 125 040538 125 2 burnished with plastic grips 0.2 - 1.3 0.9 0.4 0.3 10.5 14 6.5 79

75 52 125 040576 125

5 burnished with plastic grips 0.2 - 0.8 0.5 0.3 10.5 14 6.5 79

83

76Diagonal Cutters for electromechanics

DIN ISO 5749

76 01 125

76 05 125

with sharp, precisely aligned cutting edges for soft, hard wire and piano wire cutting edges additionally induction hardened, cutting edge hardness approx. 63 HRC lap joint Vanadium electric steel; forged, oil-hardened

Style 1low-friction double spring for gentle and even opening

Style 2without bevel for flush cutting of soft wires; low-friction double spring for gentle and even opening

Style 8particularly tapered head with small bevel for work in confined areas (cable harnesses, multiple stranded wires)


4003773- mm

Pliers Head Handles


mmB

mmD

mm g


polished plastic coated 0.4 - 3.0 2.3 1.5 0.6 14.5 16 9 90

76 03 125 018506 125 chrome plated plastic coated 0.4 - 2.5 1.8 1.0 0.6 14.5 16 9 90

76 05 125 005315 125 chrome platedwith multi-com-ponent grips

0.4 - 2.5 1.8 1.0 0.6 14.5 16 9 118



0.4 - 2.5 1.8 1.0 0.6 14.5 16 9 112


polishedwith multi-com-ponent grips

0.4 - 2.5 14.5 16 9 107


polished plastic coated 0.4 - 1.7 1.3 0.8 14.5 16 9 87

CUTTING PLIERS

84

Pliers Sets, see page 197

CUTTING PLIERS

77Electronics Diagonal Cutters DIN ISO 9654

77 01 115

77 02 115

77 12 115

77 22 115

77 32 115

for fine cutting work, e.g. in electronics and fine mechanics sturdy, zero-backlash box joint low-friction double spring for gentle and even opening the polish or mirror polish (only finish 2) together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools cutting edges additionally induction hardened, cutting edge hardness approx. 62 HRC High-grade special tool steel, forged, oil-hardened

77 01 115round head, with bevel

77 02 115round head, with small bevel

77 11 115round head, with bevel and lead catcher – no uncontrolled loss of cut wire ends

77 21 115pointed head, without bevel

77 42 115

77 52 115

77 72 115

77 22 115round head, without bevel; cutting edge hardness approx. 57 HRC

77 32 115pointed head, with small bevel

77 42 115pointed head, without bevel; cutting edge hardness approx. 57 HRC

77 52 115pointed, flat head, with small bevel; cutting edge hardness approx. 57 HRC

77 72 115pointed mini-head, with small bevel


4003773- mm

Head Handles

Ø mm Ø mm Ø mmB

mmA

mmD

mm g

77 01 115 018568 115 polished plastic coated

0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 67

77 01 130 018575 130 0.3 - 2.0 1.5 0.8 18.0 15.0 9.5 108

77 02 115 039334 115 mirror polished

with multi-component grips 0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 80

77 02 130 039341 130 mirror polished


77 11 115 018629 115 polished plastic coated 0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 70

77 12 115 043768 115 mirror polished


77 21 115 018650 115 polished plastic coated

0.3 - 1.3 1.0 14.0 11.0 7.5 64

77 21 130 018667 130 0.3 - 1.6 1.3 18.0 14.0 9.5 110

77 22 115 043782 115 mirror polished

with multi-component grips 0.3 - 1.3 1.0 14.0 11.0 7.0 80

77 22 130 040446 130 mirror polished


77 32 115 044307 115 mirror polished


77 42 115 039761 115

mirror polished


77 42 130 018773 130 0.3 - 1.6 1.3 18.0 15.0 9.5 122

77 52 115 040750 115 mirror polished


77 72 115 040958 115 mirror polished

with multi-component grips 0.3 - 0.8 10.5 9.5 6.0 69

85

CUTTING PLIERS

77Electronics Diagonal Cutters ESD DIN ISO 9654

77 02 115 ESD

77 12 115 ESD

77 22 115 ESD

77 32 115 ESD

77 42 115 ESD


for fine cutting work, e.g. in electronics and fine mechanics electrically discharging handles – dissipative sturdy, zero-backlash box joint low-friction double spring for gentle and even opening the mirror polish together with a fine film of oil offer effective rust protection – no circuit faults caused by peeling chrome from plated tools cutting edges additionally induction hardened, cutting edge hardness approx. 62 HRC with two-colour dual component grips, black/grey High-grade special tool steel, forged, oil-hardened

77 02 115 ESDround head, with small bevel

77 12 115 ESDround head, with bevel and lead catcher – no uncontrolled loss of cut wire ends

77 22 115 ESDround head, without bevel

77 32 115 ESDpointed head, with small bevel

77 42 115 ESDpointed head, without bevel

77 52 115 ESDpointed, flat head, with small bevel

77 72 115 ESDpointed mini-head, with small bevel

77 52 115 ESD

77 72 115 ESD


4003773- mm

Head Handles

Ø mm Ø mm Ø mm

Bmm

Amm

Dmm g

77 02 115 ESD 025092 115 mirror polishedwith multi-compo-nent grips

0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 82

77 12 115 ESD 025108 115 mirror polished with multi-compo-nent grips

0.3 - 1.6 1.2 0.6 14.0 11.0 7.5 80


0.3 - 1.3 1.0 14.0 11.0 7.5 80


0.3 - 1.3 1.0 0.5 14.0 11.0 7.0 79


0.3 - 1.3 0.8 14.0 11.0 7.0 78


0.3 - 1.0 0.8 0.5 11.5 14.0 7.0 79


0.3 - 0.8 10.5 9.5 6.0 69

Pliers Sets, see page 197

86

78 61 125

78 71 125

78 81 125

78 91 125

CUTTING PLIERS

78Electronic Super Knips® DIN ISO 9654

78 03 125

78 13 125

78 23 125

60°

78 31 125

78 41 125

precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics ground, very sharp cutting edges without bevel for flush cutting precision shaped tips cut wires resting on a board from 0.2 mm dia. joint with stainless steel rivet cutting edges additionally induction hardened extremely smooth movement for minimum operator fatigue with opening spring and restricted opening in INOX or special tool steel

78 03 125 / 78 23 125 INOX – stainless steel; cutting edge hardness approx. 54 HRC

78 13 125INOX – stainless steel; cutting edge hardness approx. 54 HRC; with lead catcher – no uncontrolled loss of cut wire ends

78 31 125cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC; with narrow head; special tool steel, burnished

78 41 125cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC; with narrow head; with lead catcher – no uncontrolled loss of cut wire ends; special tool steel, burnished

78 61 125cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC; also suitable for cutting glass fibre cables (fibre optics)

78 71 125special tool steel, burnished; with lead catcher – no uncontrolled loss of cut wire ends; cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC

78 81 125precision ground cutting edges with very small bevel suitable also for hard wire; special tool steel, burnished; cutting-edge hardness approx. 64 HRC

78 91 125precision ground cutting edges with very small bevel suitable also for hard wire; with lead catcher – no uncontrolled loss of cut wire ends; special tool steel, burnished; cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC

87


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mmB

mmA

mmD

mm g

78 03 125 035381 125 polishedwith multi-component grips

0.2 - 1.6 1.0 9.0 13.5 7.5 56

78 13 125 035398 125 polished with multi-component grips

0.2 - 1.6 1.0 9.0 13.5 7.5 57

78 23 125 043096 125 60° polishedwith multi-component grips

0.2 - 1.0 0.6 5.5 13.5 7.5 55


0.2 - 1.0 9.0 12.5 7.5 55

78 41 125 040767 125 burnishedwith multi-component grips

0.2 - 1.0 9.0 12.5 7.5 57


0.2 - 1.6 1.2 9.0 13.5 7.5 56


0.2 - 1.6 1.2 9.0 13.5 7.5 57


0.2 - 1.6 1.2 0.6 9.0 13.5 7.5 57


0.2 - 1.6 1.2 0.6 9.0 13.5 7.5 57

optimum cutting-edge geometry: precise, easy cutting even if strands are resting on a board

restricted opening for ergonomic hand spreading width

grooves for non-slip grip when applying a little pressure

CUTTING PLIERS

88

CUTTING PLIERS

78Electronic Super Knips® ESD DIN ISO 9654

78 03 125 ESD

78 13 125 ESD

78 61 125 ESD

78 71 125 ESD


precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics electrically discharging handles – dissipative ground, very sharp cutting edges without bevel for flush cutting precision shaped tips cut wires resting on a board from 0.2 mm dia. joint with stainless steel rivet extremely smooth movement for minimum operator fatigue with opening spring and restricted opening

78 03 125 ESDINOX - stainless steel; cutting edge hardness approx. 54 HRC

78 13 125 ESDINOX - stainless steel; cutting edge hardness approx. 54 HRC; with lead catcher – no uncontrolled loss of cut wire ends

78 61 125 ESDcutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC; special tool steel, burnished

78 71 125 ESDwith lead catcher – no uncontrolled loss of cut wire ends; cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC; special tool steel, burnished


4003773- mm

Pliers Head Handles

Ø mm Ø mmB

mmA

mmD

mm g

78 03 125 ESD 025146 125 polished with multi-component grips 0.2 - 1.6 1.0 9.0 13.5 7.5 55

78 13 125 ESD 025153 125 polished with multi-component grips 0.2 - 1.6 1.0 9.0 13.5 7.5 57

78 61 125 ESD 025184 125 burnished with multi-component grips 0.2 - 1.6 1.2 9.0 13.5 7.5 56

78 71 125 ESD 025191 125 burnished with multi-component grips 0.2 - 1.6 1.2 9.0 13.5 7.5 57

90

CUTTING PLIERS

79Precision Electronics Diagonal Cutters DIN ISO 9654

79 02 120

79 02 125

79 22 120

79 22 125

79 32 125

The subtle differenceKNIPEX precision electronics pliers are made of high-quality ball bearing steel and processed with the highest degree of care. Each opening movement is gentle and even without backlash. Each work step proceeds reliably and precisely. This makes work much easier for professionals.

precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics very precisely ground and sharp cutting edges with very small bevels for exact cutting on delicate electronic components; also available without bevel for flush cutting cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC approx. 20 % lighter than conventional electronics pliers bolted joint with particularly carefully manufactured joint surfaces for even, low-friction movement throughout the entire opening range smooth-running double spring for a gentle and even opening ergonomically optimised multi-component handles forged from chrome vanadium ball-bearing steel

79 02 120 / 79 22 120mini-head

79 02 125 / 79 22 125round head

79 12 125specially for cutting through hard wire and piano wire

79 32 125 / 79 42 125pointed head

79 52 125 / 79 62 125pointed head; with lead catcher – no uncontrolled loss of cut wire ends

79 42 125


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm Ø mmB

mmA

mmD

mm g

79 02 120 061403 120 burnished polishedwith multi-compo-nent grips 0.2 - 1.4 1.0 0.6 6.5 9 6.5 57

79 02 125 061281 125 burnished polished with multi-compo-nent grips 0.2 - 1.7 1.3 0.7 10 11 6.5 59

79 12 125 071365 125 burnished polishedwith multi-compo-nent grips 0.3 - 1.7 1.3 1.0 0.6 10 11 6.5 59

79 22 120 061427 120 burnished polished with multi-compo-nent grips 0.1 - 1.3 0.8 6.5 9 6.5 56

79 22 125 061342 125 burnished polishedwith multi-compo-nent grips 0.1 - 1.7 1.0 10 11 6.5 60


79 42 125 061380 125 burnished polishedwith multi-compo-nent grips 0.1 - 1.5 0.8 11 11 6.5 58


79 62 125 065142 125 burnished polishedwith multi-compo-nent grips 0.1 - 1.3 0.8 11 11.0 6.5 58

Pliers Sets,

see page 197

Cutting edges without bevel Cutting edges with very small bevel

91

Pliers Sets,

see page 197


79Precision Electronics Diagonal Cutters ESD DIN ISO 9654

79 02 120 ESD

79 02 125 ESD

79 22 120 ESD

79 22 125 ESD

precision pliers for ultra fine cutting work, e.g. in electronics and fine mechanics very precisely ground and sharp cutting edges with very small bevels for exact cutting on delicate electronic components; also available without bevel for flush cutting electrically discharging handles – dissipative cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC approx. 20 % lighter than conventional electronics pliers bolted joint with particularly carefully manufactured joint surfaces for even, low-friction movement throughout the entire opening range smooth-running double spring for a gentle and even opening ergonomically optimised multi-component handlesforged from chrome vanadium ball-bearing steel

79 02 120 ESD / 79 22 120 ESDmini-head

79 02 125 ESD / 79 22 125 ESDround head

79 12 125 ESDspecially for cutting through hard wire and piano wire

79 32 125 ESD / 79 42 125 ESDpointed head

79 62 125 ESD / 79 62 125 ESDpointed head; with lead catcher - no uncontrolled loss of cut wire ends

79 42 125 ESD

79 32 125 ESD

CUTTING PLIERS


4003773- mm

Pliers Head Handles

Ø mm Ø mm Ø mm Ø mmB

mmA

mmD

mm g

79 02 120 ESD 061595 120 burnished polishedwith multi-com-ponent grips

0.2 - 1.4 1.0 0.6 6.5 9.0 6.5 60

79 02 125 ESD 061519 125 burnished polished with multi-com-ponent grips

0.2 -1.7 1.3 0.7 10 11 6.5 61


0.3 - 1.7 1.3 1.0 0.6 10 11 6.5 61


0.1 - 1.3 0.8 6.5 9.0 6.5 61


0.1 - 1.7 1.0 10 11 6.5 61


0.2 - 1.5 1.1 0.6 10.5 11 6.5 61


0.1 - 1.5 0.8 10.5 11 6.5 58

79 52 125 ESD 065159 125

burnished polished with multi-com-ponent grips

0.2 - 1.3 0.9 0.5 11 11 6.5 58


0.1 - 1.3 0.8 11 11 6.5 58

92

PIPE WRENCHES AND WATER PUMP PLIERS

81Pipe Gripping Pliers

for tube fittings and connectors

DIN ISO 5743

81 03 230

81 13 230

ideal for tightening and releasing plastic pipe joints, round union nuts, etc. from 25 up to 65 mm dia. with serrated gripping jaws 4-position adjustable slip joint Chrome vanadium electric steel, forged, oil-hardened

81 13 230with plastic jaws for careful installation up to 60 mm dia.


Pliers Handles Working CapacityØ mm g

81 03 230 018957 230 chrome plated plastic coated 25 - 65 294

81 13 230 050117 230 chrome plated plastic coated 25 - 60 288

81 19 230 050124 2 pairs of plastic jaws for 81 13 230

84Cycle Pliers DIN ISO 5743

84 11 200

for very narrow screw connections Special tool steel, forged, oil-hardened

84 11 200straight head

84 21 20020° angled head


Pliers Head Handles RecessØ mm

Head thicknessmm g

84 11 200 051923 200 black atramentized polished plastic coated 6 / 10 3.5 177

84 21 200 051930 200 20° black atramentized polished plastic coated 6 / 10 3.5 182

93


831 Pipe Wrenches 90°

DIN 5234

83 10 01590°

Swedish pattern 90° angled jaws jaws with offset teeth in opposite direction teeth additionally induction hardened I-beam handle design captive adjusting nut red powder coated, jaws bright ground

Chrome vanadium electric steel, forged, oil-hardened


Pliers

Ø mm Ø Inch Inch

Clamping widthmm g

83 10 010 014188 310

90° red powder-coated

42 1 5/8 1 42 779

83 10 015 014195 420 60 2 3/8 1 1/2 60 1415

83 10 020 014201 560 70 2 3/4 2 70 2600

83 10 030 022329 650 110 4 3/8 3 110 3433

83 10 040 022336 750 130 5 1/8 4 130 4921

832 Pipe Wrenches 45°

DIN 5234

83 20 01545°

Swedish pattern 45° angled jaws jaws with offset teeth in opposite direction teeth additionally induction hardened I-beam handle design captive adjusting nut red powder coated, jaws bright ground



Pliers

Ø mm Ø Inch Inch

Clamping widthmm g

83 20 010 014218 320 45° red powder-coated

42 1 5/8 1 42 817

83 20 015 014225 430 60 2 3/8 1 1/2 60 1408

83 20 020 014232 570 70 2 3/4 2 70 2596

833 Pipe Wrenches S-Type

DIN 5234

83 30 015

Slim, S-type jaw jaws with offset teeth in opposite direction teeth additionally induction hardened three-point contact on pipes, self-locking I-beam handle design captive adjusting nut red powder coated, jaws bright ground



Pliers

Ø mm Ø Inch Inch

Clamping widthmm g

83 30 005 025221 245

red powder-coated

35 1 1/2 1/2 35 472

83 30 010 014249 320 42 1 5/8 1 42 836

83 30 015 014256 420 60 2 3/8 1 1/2 60 1540

83 30 020 014263 540 70 2 3/4 2 70 2669

83 30 030 014164 680 120 4 3/4 3 100 4366

94


86Pliers Wrenches pliers and wrench in a single tool

DIN ISO 5743

86 03 150

86 03 180

86 05 250

86 03 300

The smooth jaws grip all parallel surfaces in the capacity range with a high degree of pressure if necessary and open up almost unlimited application possibilities for the pliers wrench: e.g. for tightening locknuts, exerting pressure to activate the adhesive power of contact adhesives, edge breaking in tile work, snapping cable ties, utilisation as a small vice.

adjustable tool for tightening screwsalso excellent for gripping, holding, pressing and bending workpieces replaces a set of spanners, metric and imperial smooth jaws for cautious installation of plated fittings zero backlash jaw pressure prevents damage to edges of sensitive components adjustment at the touch of a button directly on the workpiece parallel jaws allow infinitely variable gripping of all widths to the specified maximum size reliable catching of the hinge bolt: no unintentional shifting the action of the jaws allows quick tightening and release of bolted connections using the ratchet principle lever transmission greater than 10 - 1 for strong gripping power Chrome vanadium electric steel, forged, oil-hardened

Length 150 mmthe mini pliers wrench for precision mechanics; ideal multi-purpose wrench in pocket size; indispensable companion in emergency tool kit

Length 180 mmwith narrow gripping jaws – for tightening situations that require a slim tool

Working on plated fittings without damage of the surface

Pliers wrench: zero backlash contact pressure, no damage to edges

Conventional open end wrench: edge pressure causes surface damage

Working using the ratchet principle Fast adjustment by pushing a button

95


smooth, parallel gripping jaws for work on sensitive surfaces

adjustment at the touch of a button – quick, reliable and precise

infinitely variable adjustment of widths across flats for metric and imperial workpieces

cam drive increases force to up to 10 times hand power


4003773- mm

Pliers Handles

Inch mm

Adjustment positions

B1mm

B2mm

B3mm g

86 03 150 069676 150

nickel plated

plastic coated

1 27 14 4.7 7.0 10.5 175

86 03 180 035466 180 1 3/8 35 13 5.0 8.0 12.0 254

86 03 250 033837 250 1 3/4 46 17 8.0 8.0 14.0 536

86 03 300 041429 300 2 3/8 60 22 9.5 9.5 15.0 729

86 05 150 069928 150

nickel plated


1 27 14 4.7 7.0 10.5 193

86 05 180 047162 180 1 3/8 35 13 5.0 8.0 12.0 277

86 05 250 047841 250 1 3/4 46 17 8.0 8.0 14.0 571

96

870 KNIPEX Cobra® Hightech Water Pump Pliers

DIN ISO 8976

87 01 125

87 01 150

87 01 180

87 01 250

87 01 300

87 02 250

87 03 250

KNIPEX Cobra® – the Hightech Water Pump Pliers. No more time-consuming presetting of the required opening size. Just position the upper jaw to the workpiece, push button and move close the lower jaw, ingeniously simple.

adjustment at the touch of a button directly on the workpiece fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping box-joint design: high stability because of double guide reliable catching of the hinge bolt: no unintentional shifting guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened

Length 125 mmfor use in precision mechanics, hobbies and home activities; improved access in very confined areas

Length 180 mmgood access to the workpiece

Length 250 mm / 300 mmvery large gripping capacity; good access to the workpiece; high load capacity having a slim design

Teeth set against the direction of rotation have a self-locking effect and prevent slipping on the workpiece.

Fine adjustment by pushing a button: fast and comfortable

Fast and firm adjustment directly on the workpiece87 05 250


+ 3

0%

Mini-Cobra: pocket sized tool with full fledged tool function. Capacity up to 27 mm dia.

Enormous gripping capacity; 30 % more than conventional pipe wrenches

97



Pliers Head Handles

Ø Inch Ø mm mm

Adjustment positions g

87 01 125 069935 125 grey atramentized polished with non-slip plastic coating 1 27 27 13 85

87 01 150 060116 150

grey atramentized polished with non-slip plastic coating

1 1/4 32 30 11 145

87 01 180 022015 180 1 1/2 42 36 18 170

87 01 250 022022 250 2 50 46 25 314

87 01 300 034087 300 grey atramentized polished with non-slip plastic coating 2 3/4 70 60 30 530

87 02 180 042396 180

grey atramentized polished with multi-component grips

1 1/2 42 36 18 196

87 02 250 040316 250 2 50 46 25 376

87 02 300 029144 300 2 3/4 70 60 30 580

87 03 125 073949 125

chrome plated with non-slip plastic coating

1 25 27 13 85

87 03 180 005667 180 1 1/2 42 36 18 175

87 03 250 043805 250 2 50 46 25 314

87 03 300 041382 300 2 3/4 70 60 30 530


2 50 46 25 376

87 05 300 014126 300 2 3/4 70 60 30 579

98


870 KNIPEX Cobra® XL/XXL

Pipe Wrenches and Water Pump Pliers

DIN ISO 5743

87 01 400

87 01 560

Both the KNIPEX Cobra® XL and XXL offer the performance and comfort of water pump pliers while being lighter in weight and having a greater gripping capacity than comparable pipe wrenches. The Cobra® XL can e.g. grip a 2“ pipe fitting and weighs 50 % less than a 2“ pipe wrench, which has a much lower gripping capacity. With its handy length of 400 mm, the Cobra® XL also fits into a plumber‘s tool kit.

The Cobra® XXL comes along with the weight of a 2“ pipe wrench but offers a back-up gripping capacity up to 4 1/2“.

greater gripping capacity but much lower weight than comparable pipe wrenchesfast push-button adjustment directly on the workpiece, no unintentional slipping of the joint fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping box-joint design: high stability because of double guide guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened


Self-locking on pipes and nuts. No slipping on the workpiece and less hand force required. Fast and firm adjustment directly on the workpiece.


Pliers Head Handles

Ø Inch Ø mm mm


87 01 400 005636 400 grey atramentized polished plastic coated 3 1/2 90 95 27 1214

87 01 560 044321 560 grey atramentized polished plastic coated 4 1/2 115 120 20 2750

99

Cobra® XL gripping a union nut of a 2“pipe fitting

large gripping capacity of 95 mm, would require a 3-inch pipe wrench

Cobra® XL

smaller dimensions and less weight than 1 1/2“ pipe wrenches

2“ pipe wrench

gripping the 2“ union nut exceeds the capacity of a 2“ pipe wrench; no confident working conditions


100


85KNIPEX SmartGrip® Water Pump Pliers with automatic adjustment

DIN ISO 8976

85 01 250

Adjustment to suit the workpiece is automatic with the KNIPEX SmartGrip®! Place the outer jaw on the workpiece, squeeze the handles - turn!

ideal for frequent changeovers to workpieces of different sizes automatic adjustment per one-hand operation both for right-handed and left-handed use good access to the workpiece thanks to the slim dimensions in the head and joint area and flush joint bolt self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping box-joint design: high stability because of double guide guard prevents operators' fingers being pinched locking lever for space saving transport with reliable closed handles Chrome vanadium electric steel, forged, oil-hardened

Automatic adjustment: no time-consuming trial and error-adjusting to find the correct opening size in case of differently sized workpieces (e.g. the red highlighted nuts and fittings). Everything done with a single grasp.

Locking lever for space saving transport with reliable closed handles

Slim dimensions for good access to the workpiece using one-hand operation


Pliers Head Handles

Ø Inch Ø mm mm g

85 01 250 061304 250 grey atramentized polished with non-slip plastic coating 1 1/4 32 36 370

Self-locking on pipes and nuts: no slipping on the workpiece

101

8726 KNIPEX Cobra® VDE

Hightech Water Pump Pliers, insulated


87 26 250

The adjustment procedure to adapt to the workpiece is easy and reliable with the KNIPEX Cobra® VDE: place the upper gripping jaw of the opened pliers on the workpiece, push pliers handle to close, done!

adjustment by shifting one jaw directly on to the workpiece: fast, reliable and comfortable handling opening at the touch of a button off the workpiece fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width good access to the workpiece due to slim size in the head and joint area self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping box-joint design: high stability because of double guide guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened

Quick setting without using a push-button Just push the pliers handle to adjust!


Pliers Handles

Ø Inch Ø mm mm


87 26 250 071495 250 chrome plated


2 50 46 24 340


871 KNIPEX Cobra®...matic

Water Pump Pliers

DIN ISO 8976

87 11 250


Pliers Head Handles

Ø Inch Ø mm mm


87 11 250 035473 250 grey atramentized polishedwith non-slip plastic coating

2 50 46 25 335

87 19 250 022640 Spare spring for 87 11 250

all features of the KNIPEX Cobra® 87 01 250

automatic adjustment at the touch of a button directly on the workpiece the sheltered positioned spring ensures that the pliers close automa-tically once the push-button is activated (one-hand operation!)

Special feature:

102


874 Multiple Slip Joint Spanner

DIN ISO 5743

87 41 250

The KNIPEX Multiple Slip Joint Spanner combines the convenience of the comfortable push-button adjustment on the workpiece and the function of an all-purpose tightening tool. Jaw gripping with zero backlash prevents slipping on the bolt head or rounding edges. Even rusty or thick coated bolted connections which have no surfaces capable of being gripped reliably by a conventional spanner can be managed by the exceptionally powerful closing gripping jaws of this spanner.

for metric and imperial nuts and screws with widths across flats from 10 to 32 mm (3/8" up to 1 1/4"); self-locking in the range from 17 mm on: no slipping on the workpiece zero-backlash gripping of metric or imperial hexagonal headed screws, no rounding of bolt heads reliable and tight gripping of rounded, rusty, or thick coated bolts and screwsideal for work on vehicle brake systems quick tightening of bolted connections using ratchet action adjustment at the touch of a button directly on the workpiece, also possible with one hand only fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width box-joint design: high stability because of double guide reliable catching of the hinge bolt: no unintentional shifting favourable lever action: optimum transmission of force guard prevents operators' fingers being pinched replaces a set of wrenches, ideal for tightening locknuts Chrome vanadium electric steel, forged, oil-hardened

In operation on rusted nut with rounded edges

Self-locking: no slip on workpieces; less effort required Multiple Slip Joint Spanner as the second spanner for tightening locknuts



Pliers Head Handles

Inch mm


87 41 250 054566 250 grey atramentized polished with non-slip plastic coating 3/8 - 1 1/4 10 - 32 15 328

103


875 KNIPEX Cobra® ES

Water Pump Pliers extra-slim

DIN ISO 8976

87 51 250

Due to the increasing compactness of components and machines the workspace becomes more confined.However, the requirements on the gripping force and capacity of the tools do not decrease on the other hand. KNIPEX-“Cobra“ ES allows powerful gripping in confined areas.

ideal for service, maintenance and equipment repair, in automotive and general industry long, narrow jaws particularly good access to the workpiece due to very slim construction of head and joint area firm grip also on flat material due to three-point rest adjustment at the touch of a button directly on the workpiece fine adjustment for optimum adaptation to different sizes of workpieces and a comfortable handle width self-locking on pipes and nuts: no slipping on the workpiece and low hand force required box-joint design: high stability because of double guide reliable catching of the hinge bolt: no unintentional shifting favourable lever action: optimum transmission of force guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened

Grips nuts up to 34 mm (1 5/8“) across flats

Very slim design in the complete head and joint area (compared to conventional water pump pliers)

Optimum access to the workpiece. Ideal for service, maintenance and equipment repair, in automotive and general industry



Pliers Head Handles

Ø Inch Ø mm mm

max. parallel opening width

max. gripping

depth


87 51 250 061267 250 grey atramentized

polishedwith non-slip plastic coating

1 1/4 32 34 37.0 42.0 19 328

104

88KNIPEX Alligator® Water Pump Pliers

DIN ISO 8976

88 01 180

88 01 250

88 02 250

88 05 250

88 06 250

88 07 250

self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping box-joint design: high stability because of double guide robust construction, insensitive to dirt; particularly suitable for outdoor work guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened

Length 250 / 300 mmmore output and comfort compared to conventional water pump pliers of the same length: 9-notch adjustment positioning for 30 % more gripping capacity; good access to the workpiece due to slim size in the head and joint area


Self-locking on pipes and nuts: no slipping on the workpiece; the complete actuating force can be used to turn the workpieces; not having to squeeze the pliers handles reduces the required effort

+ 3

0%

105



Pliers Head Handles

Ø Inch Ø mm mm


88 01 180 035480 180

black atramentized

polished with non-slip plastic coating

1 1/4 32 30 7 180

88 01 250 022992 250 2 50 46 9 319

88 01 300 034094 300 2 3/4 70 60 9 511

88 02 180 044222 180

black atramentized


1 1/4 32 30 7 215

88 02 250 019282 250 2 50 46 9 357

88 02 300 029151 300 2 3/4 70 60 9 565

88 03 180 042860 180

chrome plated with non-slip plastic coating

1 1/4 32 30 7 181

88 03 250 005742 250 2 50 46 9 317

88 05 180 060130 180


1 1/4 32 30 7 214

88 05 250 035497 250 2 50 46 9 354

88 05 300 042389 300 2 3/4 70 60 9 560

88 06 250 039303 250

chrome platedinsulated with multi-compo-nent grips, VDE-tested

2 50 46 9 374

88 07 250 019343 250

chrome plated with dipped insulation, VDE-tested

2 50 46 9 420

88 07 300 022350 300 2 3/4 70 60 9 661

Conventional water pump pliers

Alligator® 250/300

specially hardened teethhigh resistance to wear, allowing durable, reliable gripping

robust adjusting mechanisminsensitive to dirt, particularly suitable for outdoor work

9-notch curved adjustment positioning

box joint, double guide

Alligator® 250: convincing alternative Alli

gato

r®

no loosening of the joint connection, continuous heavy duty

30 % more gripping capacity, optimised adjustment to the workpiece and a handy handle position, slim design

The Alligator® 250 mm grips the union nut in a 3/4“ compression fitting with comfortable handle positioning

Conventional 250-mm water pump pliers do not offer appropriate fit and they have an unfavourable handle position (gripping capacity exceeded)

Alligator® 300 instead of a 1 1/2“ pipe wrench

Alligator® 300 with a gripping capacity on pipes of up to 2 3/4“ and width across flats of 60 mm; this corresponds to a gripping capacity of a 1 1/2“ pipe wrench, which is much larger and heavier

106


89Water Pump Pliers with tongue and groove joint

DIN ISO 8976

89 01 250

89 05 250

easy, convenient engagement in 5 different positions due to milled tongue non-slip joint jaw profile designed to fit screws and nuts joint design reduces strain of the centre bolt, hence no wear on pivot guard prevents operators' fingers being pinched gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC for tool length 250 mm: low wear for stable grip Chrome vanadium electric steel, forged, oil-hardened

Length 250 mmself-locking on pipes and nuts: no slipping on the workpiece and low hand force required


Pliers Head Handles

Ø Inch Ø mm mm g

89 01 200 013327 200 black atramentized polished plastic coated

1 1/4 32 30 231

89 01 250 013334 250 1 5/16 34 36 340

89 03 250 015086 250 chrome plated plastic coated 1 5/16 34 36 338

89 05 250 043836 250 chrome platedwith multi-component grips

1 5/16 34 36 371

90Mini Water Pump Pliers with tongue and groove joint

DIN ISO 8976

90 01 125

90 03 125

easy, convenient engagement in 4 different positions non-slip joint joint design reduces strain of the centre bolt, hence no wear on pivot Chrome vanadium electric steel, forged, oil-hardened


Pliers Head Handles

Ø Inch Ø mm mm g

90 01 125 035503 125 black atramentized polished plastic coated 11/16 17 14 103

90 03 125 050490 125 chrome plated plastic coated 11/16 17 14 105

107


108

SPECIAL PLIERS AND SPECIAL TOOLS

9020 Pipe Cutter for plastic conduit pipes and hoses

90 20 185

Turning the cutter slightly when cutting prevents brittle pipes splintering.

for cutting thin walled plastic pipes (conduit plastic pipes) and flexible hoses, also with fabric reinforcement, of plastic and rubber up to 25 mm dia. / 1" exterior dia. not suitable for cutting cables with opening spring and locking lever Tool body: plastic, fibreglass-reinforced Blades: special tool steel, oil-hardened, interchangeable

with replaceable blade


Cutting capacitiesØ mm g

90 20 185 067122 185 25 172

90 29 185 067139 Spare blade for 90 20 185

9025 Pipe Cutter

for composite pipes and protective tubes

90 25 20

for cutting composite pipes with diameters from 12.0 to 20.0 mm and for cutting flexible protective tubes with a diameter of 18.0 - 35.0 mm without damaging a potenially pipe inside a calibration arbor can be fitted, for example for Geberit composite pipes with 11.5 and 15.0 mm dia. Tool body: high-grade chrome vanadium electric steel, oil-hardened Blades: special tool steel, oil-hardened, interchangeable

Composite pipes of 12 - 25 mm dia. are cut cleanly and without deformation

Clean cut of protective tubes 18 - 35 mm diameter


4003773- mm

Tool Handles Composite pipesØ mm

Protective tubesØ mm

Blade lengthmm g

90 25 20 046004 210 galvanized with multi-component grips 12 - 25 18 - 35 25 332

90 29 01 031932 Spare blade for 90 25 20 (composite pipes)90 29 02 031949 1 pair of spare blades for 90 25 20 (protective pipes)90 29 15 031956 Calibration arbor for 90 25 20 (Geberit pipes)

109


9025 Pipe Cutter for composite and plastic pipes

90 25 40

for cutting thick walled plastic and composite pipes with diameters from 26.0 to 40.0 mm cuts pipes using the ratchet principle in several strokes self-adapting pipe support positions pipes of various diameters correctly for a rectangular cut Tool body: high-grade chrome vanadium electric steel, oil-hardened Blades: special tool steel, oil-hardened, interchangeable

Clean cut of thick walled plastic and composite pipes

Not suitable for thin-walled plastic pipes. Please use article number 90 20 185 for those


Tool Handles Cutting capacitiesØ mm

Cutting edge lengthmm g

90 25 40 045182 210 galvanized with multi-component grips 26 - 40 40 500

90 29 40 045199 Spare blade for 90 25 40

904 Punch Lock Riveters

90 42 250

90 42 340

to join metal section sheets used in dry walling with a lock seam for U- and C-shaped sections with max 1.2 mm metal (2 x 0.6 mm) minimum handforce required due to optimum lever transmission Pliers body: special tool steel, rolled, oil-hardened

90 42 250for one-hand operation

Setting the pliers for connection of two metal section sheets

The punching tool is squeezed through the metal section sheets


Pliers Handles Capacity

g

90 42 250 047865 250 burnished with multi-component grips max. 1,2 (2 x 0,6) 676

90 42 340 071884 340 burnished with multi-component grips max. 1,2 (2 x 0,6) 901

90 49 340 028079 Spare punch for 90 41 340 and 90 42 34090 49 340 M 028499 Spare die for 90 41 340 and 90 42 340

110


9055 Sheet Metal Nibbler

90 55 280

for cutting iron, copper or aluminium sheet metal up to max. 1.2 mm thickness, plastic up to max. 2.0 mm thickness materials are cut without deformation clean cut edges – no trimming activities needed with chip breaker easy handling cutting width: 2.7 mm Tool body: special tool steel, rolled, oil-hardened Blades: special tool steel, oil-hardened, interchangeable

Notching and chip breaking in a single pass Notching without chip breaking


Tool Handles

g

90 55 280 026730 280 nickel plated with multi-component grips 461

90 59 280 027355 Spare blade for 90 55 280

9061 Notching Pliers

90 61 20

The KNIPEX Notching Pliers produces the most common notches in plastic ledges and cable ducts in a simple, fast and clean way. No time-consuming sawing out or nibbling and no additional work required.

special pliers for notching recesses into plastic ledges and plastic casings for electric and sanitary installation notches can be enlarged by initial and final cut clean cut edges – no trimming activities needed easy handling with opening spring, opening limiter and locking lever Pliers body: special tool steel, rolled, oil-hardened



g

90 61 16 051947 250 burnished with plastic grips

16 x 32 mm 403

90 61 20 051954 250 20 x 29 mm 414

111


907 Revolving Punch Pliers

90 70 220

to punch holes into leather, textiles and plastic material with six interchangeable punches: 2.0 / 2.5 / 3.0 / 3.5 / 4.0 / 5.0 mm dia. with opening spring and locking lever powder-coated for reliable protection against rust Pliers body and punches: special tool steel, oil-hardened

Interchangeable punches


Pliers Finish

g

90 70 220 019411 220 red powder-coated powder coated 251

910 Tile Nibbling Pincer (parrot beak pincer)

91 00 200

enlarges holes in tiles and forms tile edges Special tool steel, forged, oil-hardened


Pliers Head

g

91 00 200 013754 200 black atramentized polished 158

911 Tile Breaking Pincer

91 11 190

for breaking tiles to a scored line moveable, self-aligning jaw, rubberlined to protect the tile Special tool steel, forged, oil-hardened


Pliers Handles

g

91 11 190 042310 190 black lacquered plastic coated 317

112


913 Glass Breaking Pincer

DIN ISO 5743

91 31 180

for breaking glass to a scored line Special tool steel, forged, oil-hardened


Pliers Head Handles Jaw widthmm g

91 31 180 069744 180 black atramentized polished plastic coated 24,0 245

91Glass Nibbling Pincers DIN ISO 5743

91 51 160

for breaking off narrow strips of glass to a scored line for finishing off glass edges to required profile Special tool steel, forged, oil-hardened

91 71 160narrow version, with opening spring





916 Flat Nose Grozing Pliers

DIN ISO 5743

91 61 160

with soft gripping jaws for trimming glass edges, e.g. when making leaded glass windows Special tool steel, forged, oil-hardened




113

PRECISION TWEEZERS

92Precision Tweezers pointed shape

92 22 04

92 22 06

92 22 07

92 23 05

92 24 01

for fine mounting work straight pattern smooth gripping surfaces particularly slim tips

92 22 04non-reflective matt finished; gripping surfaces matt finished for optimum grip; Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality

92 22 06non-reflective matt finished; gripping surfaces matt finished for optimum grip; Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality

92 22 07non-reflective matt finished; stainless, anti-magnetic and acid-proof

92 23 05Titanium; electrically conductive; lightweight; non-reflective matt finished; stainless, anti-magnetic and acid-proof

92 24 01mirror finish nickel plated and polished


Finish

g

92 22 04 054665 130 stainless, anti-magnetic 20


92 22 07 054689 115 stainless, anti-magnetic, acid-proof 12

92 23 05 054726 120 Titanium, anti-magnetic, acid-proof, stainless 10

92 24 01 054733 120 nickel plated 15

92Precision Tweezers

92 02 53

45°

92 02 54

45°

92 02 55

92 12 52

85°

smooth gripping surfaces non-reflective matt finished

92 02 53for SMD-technology*; angled tips, width approx. 1 mm; gripping surfaces matt finished for optimum grip; Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality

92 02 54for SMD-technology*; angled tips, width approx. 1 mm; gripping jaws 3.5 mm wide, integrated profile for reliable gripping of cylindrical components of 0.6 mm dia.; gripping surfaces matt finished for optimum grip; Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality

92 02 55gripping jaws 3.5 mm wide, for cylindrical components of 0.8 mm dia.; serrated handles; stainless, anti-magnetic and acid-proof

92 12 52angled tips; extra strong tips; stainless, anti-magnetic


Finish

g

92 02 53 054603 120 45° stainless, anti-magnetic 16




* SMD-Technology: technique for soldering surface mounted components on printed circuit boards without using holes

114

PRECISION TWEEZERS

92Precision Tweezers needle-pointed shape

92 22 12

92 22 13

92 32 29

45°

92 34 28

45°

for ultra fine mounting work extra fine tips smooth gripping surfaces stainless, anti-magnetic non-reflective matt finished

92 22 12straight pattern

92 22 13American shape, solid; straight pattern; stainless, anti-magnetic and acid-proof

92 32 29sickle-shaped tips; Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality; gripping surfaces matt finished for optimum grip

92 34 28angled tips


Finish

g





92Precision Tweezers with centering pin

pointed shape

92 22 35

92 24 34

92 34 36

45°

92 34 37

45°

universally applicable narrow tips gripping surfaces with fine transverse serration serrated handles

92 22 35straight pattern; non-reflective matt finished; stainless, anti-magnetic and acid-proof

92 24 34straight pattern; nickel plated

92 34 36angled tips; nickel plated

92 34 37angled tips; black non-reflective lacquered


Finish

g


92 24 34 054740 155 nickel plated 21

92 34 36 054832 155 45° nickel plated 23

92 34 37 054849 155 45° black lacquered 21

92Precision Tweezers round slim shape

92 52 23

round tips, approx. 2 mm wide smooth gripping surfaces stainless, anti-magnetic and acid-proof Chrome nickel steel, stainless, non-magnetic, acid-proof


Finish

g

92 52 23 054894 120 stainless, anti-magnetic, acid-proof

17

115

92Plastic Tweezers

92 69 84

trapezoidal tips, approx. 3.5 mm wide serrated gripping surfaces serrated handles Tweezers body: solid plastic, temperature-resistant up to 130°C


Finish

g

92 69 84 054948 130 plastic 19

92Precision Tweezers rectangular blunt

92 84 18

mounting tweezers rectangular tips, approx. 0.9 mm wide gripping surfaces with fine transverse serration nickel plated Spring steel, high-strength


Finish

g

92 84 18 054986 125 nickel plated 19

PRECISION TWEEZERS

92Precision Tweezers blunt shape

92 44 42

92 64 43

92 64 44

92 70 46

92 72 45

universally applicable straight pattern wide, round tips serrated handles

92 44 42jewellers‘ tweezers; round tips, approx. 2 mm wide; gripping jaws with fine crosswise serration (cross-hatched); nickel plated

92 64 43round tips, approx. 3.0 mm wide; gripping surfaces with fine transverse serration; nickel plated

92 64 44round tips, approx. 3.5 mm wide; gripping surfaces with fine transverse serration; nickel plated

92 70 46round tips, approx. 3.5 mm wide; gripping surfaces with fine transverse serration; black non-reflective lacquered

92 72 45round tips, approx. 3.5 mm wide; serrated gripping surfaces; non-reflective matt finished; stainless, anti-magnetic and acid-proof


Finish

g

92 44 42 054887 140 nickel plated 21

92 64 43 054917 120 nickel plated 17

92 64 44 054924 145 nickel plated 23

92 70 46 055075 145 black lacquered 26


116

PRECISION TWEEZERS

92Precision Tweezers insulated

IEC 60900

92 27 61

92 27 62

92 37 64

45°

92 67 63

tested according IEC 60900 : 2004 with dipped insulation nickel plated Spring steel, high-strength

92 27 61for ultra fine mounting work; extra fine tips; straight pattern; gripping surfaces matt finished for optimum grip

92 27 62straight pattern; gripping surfaces with fine transverse serration

92 37 64angled tips; gripping surfaces with fine transverse serration

92 67 63straight pattern; serrated gripping surfaces


Finish

g

92 27 61 054757 130 with dipped insulation 32


92 37 64 054856 150 45° with dipped insulation 34


92Cross-Over Tweezers

92 94 91

92 95 89

92 95 90

45°

for holding small parts without finger pressure for efficient clamping nickel plated Spring steel, high-strength

92 94 91trapezoidal tips; straight pattern; gripping surfaces with fine transverse serration; serrated handles

92 95 89narrow tips; straight pattern; gripping surfaces with fine transverse serration; handles with plastic attachement

92 95 90narrow tips; angled tips; gripping surfaces with fine transverse serration; handles with plastic attachement


Finish

g

92 94 91 055006 160 nickel plated 35

92 95 89 055013 160 nickel plated 30

92 95 90 055020 160 45° nickel plated 32

117

PRECISION TWEEZERS

92Precision Tweezers ESD

92 08 78 ESD

45°

92 08 79 ESD

92 28 69 ESD

92 28 70 ESD

92 28 71 ESD

92 28 72 ESD

92 38 75 ESD

45°

92 58 74 ESD

Chrome nickel steel: stainless, anti-magnetic (18/10), very popular electronics quality ESD coating: non-reflective black, with a surface resistance of approx. 105 Ohm tips non-reflective brushed gripping surfaces matt finished for optimum grip Chrome nickel steel, stainless, anti-magnetic

92 08 78 ESDfor SMD-technology*; angled tips; smooth gripping surfaces

92 08 79 ESDshaped to grip horizontal cylindrical components of 1.0 mm dia.; smooth gripping surfaces; serrated handles

92 28 69 ESDstraight pattern; strong tip; smooth gripping surfaces

92 28 70 ESDstraight pattern; fine tip; smooth gripping surfaces

92 28 71 ESDneedle-pointed tips; straight pattern; smooth gripping surfaces

92 28 72 ESDAmerican shape, solid; long tips; straight pattern; smooth gripping surfaces

92 38 75 ESDsickle-shaped tips; smooth gripping surfaces

92 58 74 ESDround tips, approx. 2 mm wide; straight pattern; smooth gripping surfaces

92 78 77 ESDround tips, approx. 3.5 mm wide; straight pattern; serrated gripping surfaces; serrated handles

92 88 73 ESDrectangular tips, approx. 0.9 mm wide; gripping surfaces with fine transverse serration

92 78 77 ESD

92 88 73 ESD


Finish

g

92 08 78 ESD 054634 120 45° stainless, anti-magnetic, electrically dissipative 16

92 08 79 ESD 054641 120 stainless, anti-magnetic, electrically dissipative 16





92 38 75 ESD 054863 120 45° stainless, anti-magnetic, electrically dissipative 17




* SMD-Technology: technique for soldering surface mounted components on printed circuit boards without using holes

118


9410 Pipe Cutter for plastic conduit pipes

(electrical installation work)

94 10 185

for clean cutting of plastic pipes (e.g. plastic conduit pipes) with 6 - 35 mm dia. not suitable for cutting cables blade is replaceable and can be retracted from any position low force requirement due to special blade geometry and optimum transmission minimum operator fatigue due to ergonomic handle design and incremental ratchet blade feedHousing: die-cast aluminium, red lacquered


Body CapacityØ mm

Cutting edge length mm g

94 10 185 047025 185 die-cast aluminium body, red lacquered 6.0 - 35.0 35 583 94 19 185 047032 Spare blade for 94 10 185

Blade: special tool steel, oil-hardened

9415 Cutter for ribbon cable

94 15 215

for crushing-free cutting of ribbon cable up to 56 mm width exchangeable cutting base with try square for rectangular cuts with opening spring and locking lever Tool body: tool steel, rolled, oil-hardened Blade: standard trapezoidal blade, replaceable


Tool Handles Blade lengthmm g

94 15 215 046011 215 chrome plated with plastic grips 56 346 94 19 215 046219 Set with 10 spare blades for 94 15 215 / 94 35 215

943 Mitre Shears for plastic and rubber sections

94 35 215

for crushing-free cutting of plastic, rubber and soft timber sections; also for ribbon cable up to 56 mm width exchangeable cutting base try square angle for 45°-cuts and markings for 60°-, 75°-, and 90°-cuts with opening spring and locking lever Tool body: special tool steel, rolled, oil-hardened Blade: standard trapezoidal blade, replaceable


Tool Handles Blade lengthmm g

94 35 215 046028 215 chrome plated with plastic grips 56 397

119


9502 Vinyl Shears also for cable ducts

95 02 10

95 02 21

special lever transmission very effective blade geometry Tool body: high-grade chrome vanadium electric steel, oil-hardened Blade: special tool steel, oil-hardened

95 02 10for plastic material up to approx. 6.0 mm thickness (e.g. PE with up to 63 Shore)

95 02 21for cutting and shortening cable ducts, also for plastic material up to 4.0 mm thickness

95 02 10: powerful cutting of plastics up to 6.0 mm in thickness

95 02 21: blade length 110 mm for cutting wide cable ducts


Tool Handles Cutting capacitiesmm

Blade lengthmm g

95 02 10 047872 225 burnished with multi-component grips 4.0 - 6.0 60 459

95 02 21 052128 275 burnished with multi-component grips max. 4.0 110 665

9503 Shears for KEVLAR® fibres

95 03 160 SB

only for cutting fibres of KEVLAR® in optical fibre cables, not recommended for other materials precisely ground blades with serration prevent the fibres from slipping and guarantee a clean cut riveted precision joint, for low-friction movement and smooth and even cutting of the thin KEVLAR® fibres hard-chrome plated, ground surface Shears body: chrome vanadium electric steel, oil-hardened User-friendly handles: plastic, impact-proof


Shears Handles

g

95 03 160 SB 043362 160 chrome plated plastic coated 85

KEVLAR® is a registered trademark of E. I. du Pont de Nemours and Company

120


9505 Combination Shears

95 05 140

95 05 18540°

95 05 190

for cutting cardboard, plastics, aluminium, brass and copper foils not suitable for steel wire or iron sheets precision ground, hardened blades with opening spring and locking lever guard prevents operators‘ fingers being pinchedadjustable bolted joint Shears body: surgical steel, stainless, vacuum-hardened Handles: plastic, impact-resistant

95 05 185angled shape - for easy execution of long cuttings; ergonomically shaped plastic handles


Head Handles

g




95Cable Shears

95 05 165

95 06 230

not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades no crushing, slight deformation of the cable only guard prevents operators‘ fingers being pinched adjustable bolted joint Shears body: surgical steel, stainless, vacuum-hardened Handles: plastic, impact-proof

95 05 165cuts cables up to 10 mm dia. / 24 mm²; with opening spring and locking lever; blades made of stainless steel; oil-hardened and tempered

95 06 230for copper single conductors up to 16 mm², multiple stranded wires up to 50 mm², fine stranded up to 70 mm² and aluminium conductors multiple stranded wires up to 70 mm²; easy cutting with one-hand operation due to high transmission ratio; stainless – special grade – steel, oil-hardened and tempered


4003773- mm

Head Handles

Ø mm mm²

AWG

g

95 05 165 019596 165 polished plastic coated 10 24 3 111

95 06 230 006305 230 polished plastic insulated, VDE-tested 16 50 1/0 274

122


95Cable Shears

95 11 165

95 12 165

95 16 165

95 22 165

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades clean and smooth cut without crushing and deformation easy cutting with one-hand operation guard prevents operators‘ fingers being pinched adjustable bolted joint, self-retaining screwHigh-grade special tool steel, forged, oil-hardened

Style 2internal opening spring, protected and captive

Cut performed with a Diagonal Cutter: high effort required, inaccurate cut, considerable deforming and crushing of the cable

Cut performed with a Cable Shears: easy, clean cut without any deformation of the cable


4003773- mm

Style Tool Handles

Ø mm mm²

AWG

g

95 11 165 040323 165 1 burnished plastic coated 15 50 1/0 215

95 12 165 029182 165 1 burnished with multi-component grips 15 50 1/0 250

95 16 165 039648 165 1chrome plated


15 50 1/0 262

95 21 165 069805 165 2 burnished plastic coated 15 50 1/0 215

95 22 165 069812 165 2 burnished with multi-component grips 15 50 1/0 254

95 26 165 069980 165 2chrome plated


15 50 1/0 275

123



95 11 200

95 12 200

95 16 200

95 17 200

The twin cutting edge allows a comfortable handle position in all cutting situations within the specified cutting capacity.

for cutting copper and aluminium cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades clean and smooth cut without crushing and deformation by dividing the cutting actions into initial cut (insulating sheath in the front cutting area) and final cut (conductor in the back cutting area), cables up to Ø 20 mm can be cut in one-hand operation less effort required due to favourable lever ratio and optimised cutting-edge geometry guard prevents operators‘ fingers beng pinched adjustable bolted joint, self-retaining screw High-grade special tool steel, forged, oil-hardened

Initial cut: using the front cutting edge to cut the insulating sheath on larger cable diameters leaves an ergonomic handle opening width.

Final cut: after cutting the sheath in the front profile the cut is finished through the metal part of the cable in the rear profile. Initial cut in the front profile, final cut in the rear profile – to keep iit as easy as possible.


4003773- mm

Tool Handles

Ø mm mm²

AWG

g

95 11 200 043928 200 burnished plastic coated 20 70 2/0 283

95 12 200 047834 200 burnished with multi-component grips 20 70 2/0 324

95 16 200 026761 200 chrome platedinsulated with multi-component grips, VDE-tested

20 70 2/0 340

95 17 200 026952 200 chrome plated with dipped insulation, VDE-tested 20 70 2/0 360

124


95Cable Shears

95 12 500

95 17 500

for cutting copper and aluminium conductors as well as multiple stranded cables not suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation low handforce required due to favourable lever ratio and special blade geometry short design, length only 500 mm low weight guard prevents operators‘ fingers being pinchedadjustable bolted joint Cutter head: vanadium electric steel, forged, oil-hardened Handles: aluminium tube, high-strength

Large cutting capacity: max. 27 mm dia. / 150 mm²


4003773- mm

Head Handles

Ø mm mm²

AWG

g

95 12 500 069966 500 burnished with multi-component grips 27 150 5/0 1090

95 17 500 026785 500 polished with dipped insulation, VDE-tested 27 150 5/0 1477

95Cable Shears

95 21 600

for cutting copper and aluminium conductors as well as multiple stranded cables not suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation favourable transmission ratio due to double lever guard prevents operators‘ fingers being pinched adjustable bolted joint bolted cutter head, replaceable Blade head: high-grade chrome vanadium electric steel, forged, oil-hardened Handles: steel tube


4003773- mm

Head Handles

Ø mm mm²

AWG

g

95 21 600 025252 600 polished with plastic grips 27 150 5/0 1836


95 29 600 021803 Spare cutter head for 95 21 600 / 95 27 600

125


953 Cable Cutters (ratchet action)

95 31 250

95 31 280

95 36 250

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation one-hand operation using ratchet principle little handforce required due to very high transmission ratio two-stage ratchet drive for easy cutting simple handling as a result of low weight and compact design – can be used even in confined areas guard prevents operators‘ fingers being pinched High-grade special tool steel, forged, oil-hardened

95 31 / 36 280suitable for aluminium sector cable up to 4 x 150 mm²

95 31 280: Large cutting capacity: maximum 52 mm dia. / 380 mm²

Ratchet principle and two-stage ratchet drive for easier cutting

95 31 250 / 280: Fixed handle with support area as an aid to position the cutters on a flat surface


4003773- mm

Tool Handles

Ø mm mm²

MCM

g

95 31 250 043935 250 black lacquered with multi-component grips 32 240 500 676

95 31 280 043942 280 black lacquered with multi-component grips 52 380 750 860

95 36 250 026884 250 black lacqueredinsulated with multi-component grips, VDE-tested

32 240 500 652

95 36 280 026891 280 black lacquered insulated with multi-component grips, VDE-tested

52 380 750 835

95 39 250 022244 Movable spare blade for 95 31 250 / 95 36 250


126


9532 Cable Shears (ratchet action)

with telescopic handles

95 32 038

Handles adjustable in length and angular position for easier work: set the handle length to the optimum lever for powerful cutting; put the handles at an angle for a comfortable gripping position

for cable diameters up to 38 mm, handles can be positioned at an angle to set the optimum handle width, which makes the shear also suitable for work in confined areas comfortable work thanks to ratchet action and low weight heavy duty telescopic handles made of oval aluminium tubing; extendable up to 770 mm for maximum leverage on large cable diameters; retractable down to 570 mm for minimum space requirements during transport replaceable cutting head extensive cutting range up to max. Ø 38 mm or max. 280 mm² (e.g. 4 x 70 mm² NYY) in copper and aluminium cables easier, neater cut due to optimised cutting-edge geometry adjustable bolted joint Cutting head: special quality high-grade tool steel, oil-hardened Handles: high-strength oval aluminium tubing

Setting of a favourable handle width

After the first partial cut, the handles open by ratchet action

Repeat cutting and opening actions until the cable is cut through

with adjusting button


4003773- mm

Head Handles

Ø mm mm²

MCM

g

95 32 038 071556 570 burnished with multi-component grips 38 280 550 1980

95 39 038 073260 Spare cutter head for 95 32 038

Cable shears with adjustable telescopic handles allowing angular positioning

127


9532 Cable Cutters (ratchet action)

with telescopic handles

95 32 060

for copper and aluminium single conductors as well as multiple stranded cables – also with hard rubber or plastic sheath not suitable for steel wire and wire ropes also suitable for cables with iron sheath reinforcement little hand force required for cutting due to optimum transmission ratio high cutting capacity due to two-hand operation and ratchet action the blade can be opened in any cutting position

95 32 060 tool in length: 630 to 830 mm; weight only approx. 3820 g


4003773- mm

Head Handles

Ø mm mm²

MCM

g


60 740 1400 3820

95 32 100 071570 680 100 960 1900 4980



previous with steel

tubing

newwith heavy-duty aluminium telescopic handles

30 % weight reduction

handle length with multiple position adjustment from 400 - 600 mm (short transport length, individual adaptation to working conditions

Blade: special-quality high-grade tool steel, oil-hardened Handles: high-strength oval aluminium tubing

128


956 Wire Rope Shears forged

double function: neat cutting, precise crimping

95 61 190

95 62 190

Cuts all wire ropes without splaying, including those that are extremely strong, such as for example tyre cord

with two crimping dies for end caps on Bowden cable sheaths and end ferrules for traction cables comfortable work thanks to handy, slim design and internal opening spring bolted joint for precise blade guidance, re-adjustable high leverage for reduced effort cutting-edge hardness approx. 64 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened

Crimping of the end ferrule onto the traction cable

Crimping of the end caps on the Bowden cable sheath


4003773- mm

Head Handles


95 61 190 040651 190 polished plastic coated 7 6 4.0 2.5 314

95 62 190 071976 190 polished with multi-component grips 7 6 4 2.5 314

Precise guiding through a bolted joint

Transport lock and restricted opening

Crimp profiles

Internal opening spring

129


956 Bowden Cable Cutter

95 61 150

for Bowden cables and soft wire rope up to 3.0 mm dia. (also V2A) smooth and clean cutting due to special shape of the cutting edges sickle shape cutting edges surround the material and prevent the wire rope fanning out little handforce required due to very high transmission ratio with opening spring and locking device cutting edges additionally induction hardened


4003773- mm

Shears Head Handles

Ø mm g

95 61 150 065197 150 black atramentized polished plastic coated 3 205

High-grade special tool steel, forged, oil-hardened

95Wire Rope and ACSR-Cable Cutters

95 71 600

95 77 600

for wire ropes and steel rods, copper and aluminium cables suitable for cutting overhead cables with strain relief wire (ACSR-cables) angular cutting blades allow cutting of single rope wire optimum transmission ratio for high cutting performance bolted cutter head, replaceable low weight Cutter head: high-grade special tool steel, oil-hardened Handles: aluminium, high-strength

95 81 600with reinforced cutter head for higher performance, also cuts piano wire


4003773- mm

Head Handles

mm² Ø mm Ø mm Ø mm

AWG

g

95 71 445 014522 445 polished with plastic grips 95 10.0 7.0 3/0 1083

95 71 600 014539 600 polished with plastic grips 150 14.0 9.0 5/0 1716

95 77 600 025313 600 polished with dipped insulation 150 14.0 9.0 5/0 2359

95 81 600 025344 600 polished with plastic grips 150 16.0 10.0 4.5 5/0 2256




130

CRIMPING PLIERS

9700 Crimp Grip Pliers

97 00 215 A

■ for solder-free electrical connections ■ quick release lever ■ high contact pressure with minimum handforce using toggle

lever transmission ■ reproducible crimping quality with high tensile strength because

of zero point lock ■ adjustable crimping pressure ■ Special steel, high-strength

97 00 215 Dcrimps conductor and insulation in one single operation

Number of crimping positions


Pliers Head Handles Applications Capacitymm²

AWG

g

97 00 215 A 006497 215 burnished insulated terminals and plug connectors

0.5 - 6.0 20 - 10 3 520

97 00 215 B 006503 215 burnished nickel plated

non-insulated open plug-type connectors (plug width 6.3 mm)

0.5 - 6.0 20 - 10 3 520

97 00 215 D 006527 215 burnished insulated terminals and plug connectors

0.5 - 6.0 20 - 10 3 513

972 Crimping Pliers

97 21 215

97 22 240

■ for cutting cables, stripping wire and crimping insulated and non-insulated terminals, connectors and plug type connectors

■ with threaded holes for cutting copper and brass screws threaded M 2.6 / 3.0 / 3.5 / 4.0 and 5.0 mm

■ Special steel, high-strength



Pliers Handles Applications Capacitymm²

AWG

g

97 21 215 019688 215 burnishedwith plastic grips

insulated terminals and plug connectors

0.75 - 6.0 18 - 10 3 224

97 21 215 B 019695 215 burnished with plastic grips

non-insulated open plug-type connectors (plug width 6.3 mm)

0.5 - 2.5 20 - 13 3 221

97 21 215 C 019701 215 burnishedwith plastic grips

non-insulated terminals and plug connectors

0.5 - 6.0 20 - 10 3 222

97 22 240 070726 240 black lacque-red



0.75 - 6.0 18 - 10 3

300non-insulated open plug-type connectors (plug width 6.3 mm)

0.5 - 6.0 20 - 10 3

131

CRIMPING PLIERS

9732 Crimping Pliers

97 32 225

■ for cutting cables, stripping wire and crimping insulated and non-insulated terminals and connectors

■ with threaded holes for cutting copper and brass screws threaded M 2.6 / 3.0 / 3.5 / 4.0 and 5.0 mm

■ Special steel, high-strength




AWG

g

97 32 225 019718 225 burni-shed

with plastic grips


0.5 - 6.0 20 - 10 3 240


0.5 - 2.5 20 - 13 3

9740 Insertion tool for LSA-Plus and identical

97 40 10

■ tool for putting on boards, sockets and fields ■ pushing down and cutting in one operation ■ for UTP and STP cables, conductor 0.4 - 0.8 mm dia. ■ with integrated pulling hook and release blade ■ Housing: plastic, impact-proof

Putting down and cutting the cable in one operation

With integrated pulling hook


Head Applications CapacityØ mm g

97 40 10 044895 175 burnished UTP- and STP-cables, LSA-Plus and identical 0.4 - 0.8 100

132

CRIMPING PLIERS

9733 KNIPEX MultiCrimp®

Crimping Pliers with quick changer magazine

97 33 01

97 33 02

Compact, inexpensive and light-weight crimping pliers for fitting and repairs. The electrician needs only one tool now instead of five as before.

■ just one tool for the most common crimping applications ■ crimping dies changed quickly and easily without any additional tool ■ secure and protected storage of the interchangeable dies in a

round magazine ■ comfortable, powerful crimping pliers in professional quality ■ same reliable crimping results as with fixed crimping dies ■ repetitive, high crimping quality due to precision dies and integral

lock (self-releasing mechanism) ■ Chrome vanadium electric steel in special quality, oil-hardened ■ Round magazine: plastic, fibreglass-reinforced

97 33 01Crimping pliers with round magazine and three interchangeable die sets for non-insulated open plug connectors (4.8 + 6.3 mm width) from 0.5 - 6.0 mm²; insulated terminals + plug connectors from 0.5 - 6.0 mm²; end sleeves (ferrules) from 0.25 - 6.0 mm²

97 33 02Crimping pliers with round magazine and five interchangeable die sets for non-insulated open plug connectors (4.8 + 6.3 mm width) from 0.5 - 6.0 mm²; insulated terminals + plug connectors from 0.5 - 6.0 mm²; end sleeves (ferrules) from 0.25 - 6.0 mm²; non-insulated terminals and plug connectors from 0.5 - 10 mm²; non-insulated butt connectors from 1.5 - 10 mm²

Changing position: service lever opens out for parallel jaw positioning

Changing the crimping dies: unlock the magazine position, take out the set of dies which the pliers have been pushed on

Fold in the service lever and press the pliers – ready for use again

The MultiCrimp® Pliers are not available in the U.S.A.

133

Magazine for crimping dies can be carried on a belt




AWG

g

97 33 01 066927 250 burnished

with multi-com-ponent grips

non-insulated, open plug-type connectors

0.5 - 6.0 20 - 10 3

770insulated terminals and plug connectors

0.5 - 6.0 20 - 10 3

End Sleeves (ferrules) 0.25 - 6.0 23 - 10 5

97 33 02 066934 250 burnished with multi-com-ponent grips


0.5 - 6.0 20 - 10 3

870


0.5 - 6.0 20 - 10 3

End Sleeves (ferrules) 0.25 - 6.0 23 - 10 5


0.5 - 10.0 20 - 7 4

non-insulated butt connectors

1.5 - 4.0 6.0 + 10.0*

15 - 11 10 + 7

32

97 39 05 070078 Crimping dies for non-insulated open plug-type connectors 4.8 + 6.3 mm

97 39 06 070085 Crimping dies for insulated terminals + plug connectors

97 39 08 070092 Crimping dies for end sleeves (ferrules)

97 39 13 070108 Crimping dies for non-insulated terminals + plug connectors

97 39 30 070115 Crimping dies for non-insulated butt connectors

97 39 90 070061 Quick Changer Magazine empty

Clearly visible marking on the crimping dies with pictograms

* compression joints in conformance to DIN 46267

CRIMPING PLIERS

The MultiCrimp® Pliers are not available in the U.S.A.

134

CRIMPING PLIERS

9743 Crimp System Pliers

for exchangeable crimping dies

97 43 200

97 43 200 A

With the possibility of crimping almost all currently available crimping connections with just one tool and state-of-the-art crimping pliers technology, the crimping system pliers solves almost all tasks in mobile and stationary crimping technology and is an excellent tool for professionals to use for standard crimping.

■ just one tool for almost 1000 crimping applications ■ almost parallel crimping die movement ■ repetitive, high crimping quality due to precision dies and integral

lock (self-releasing mechanism) ■ crimping pressure has been set precisely (calibrated) in the factory,

re-adjustable ■ optimum transmission of force due to lever action for

fatigue-reduced operation ■ ergonomically designed handles ■ different locators for precise positioning of the connectors ■ crimping dies for applications not covered in the range offered here,

may be available on request ■ Chrome vanadium electric steel in special quality, oil-hardened

97 43 200comes in a plastic case; foam insert with recesses for crimping dies and locators; with service tool (Allen key), screws and nuts; without crimping dies

97 43 200 APliers without crimping dies, without case

97 43 05with attached crimping dies for non-insulated open plug-type connectors (4.8 and 6.3 mm connector width)

97 43 06with attached crimping dies for insulated terminals and plug connectors

Crimp System Pliers 97 43 200 with crimping dies 94 49 30 for non-insulated butt connectors

Crimp System Pliers 97 43 200 with crimping dies 97 49 35 for spark plug connectors

97 43 200 with crimping dies 97 49 61 and revolvable locator 97 49 90 for turned types of connectors with varying pin diameters

97 43 400 Crimp System Pliers with crimping dies 97 49 24 and locator 97 49 93 for D-Sub plugs




AWG

g

97 43 200 030812 200 burnishedwith multi-com-ponent grips

see crimping dies table 988

97 43 200 A 071587 200 burnished with multi-com-ponent grips

see crimping dies table 574

97 43 05 031031 200 burnishedwith multi-com-ponent grips

Crimp System Pliers for non-insula-ted open plug-type connectors (4.8 and 6.3 mm connector width)

0.5 - 6.0 20 - 10 3 618

97 43 06 031048 200 burnished with multi-com-ponent grips

Crimp System Pliers for insulated terminals and plug connectors

0.5 - 6.0 20 - 10 3 610

SOLA

R C

ON

NEC

TOR

S

135

Special profiles

on request

CRIMPING PLIERS

9749 Crimping Dies for Crimp System Pliers

SOLA

R C

ON

NEC

TOR

S


Number of crimping positions g


Applications Capacitymm²

AWG Capacity SW mm

SleevesØ mm

97 49 04 030850 non-insulated Plug Connectors 0.1 - 2.5 27 - 13 4 42

97 49 05 030867 non-insulated Plug Connectors 0.5 - 6.0 20 - 10 3 46

97 49 06 030836 insulated terminals and plug connectors 0.5 - 6.0 20 - 10 3 45

97 49 08 030874 End Sleeves (ferrules) 0.25 - 6.0 23 - 10 5 49

97 49 09 030881 End Sleeves (ferrules) 10 / 16 / 25 7/ 5/ 3 3 50

97 49 13 030843 non-insulated terminals and plug connectors 0.5 - 10.0 20 - 7 4 37

97 49 15 043164 lug connectors and non-insulated open plug type connectors (plug width 6.3 mm)

1.25-2.5 + 3.0-6.0

17 - 13; 12 - 9 2 + 1 56

97 49 16 040675 insulated terminals and plug connectors 10.0 - 16.0 7 / 5 2 46

97 49 18 063186 Twin end sleeves (ferrules) for two flexible conductors 2x6 / 10 / 16 10 / 7 / 5 3 48

97 49 19 030898 End Sleeves (ferrules) 35 - 50 2 / 0 2 46

97 49 20 045069 F-connectors for TV and satellite connections 7.0; 8.4; 8.1 7.7; 9.5; 9.5 3 50

97 49 23 052135 non-insulated terminals and plug connectors 16 + 25 5 + 3 2 45

97 49 24 030911 D Sub; HD 20; HDE plug 0.03 - 0.56 32 - 20 3 41

97 49 30 030904 non-insulated butt connectors 1.5 - 4.0 6.0 + 10.0*

15 - 11 10 + 7

32 37

97 49 35 034315 spark plug connectors and distributors 1 17 5 52

97 49 40 030959 Coax connectors RG 58, 59, 62, 71, 223 5.4; 6.48; 1.72

6.4; 7.6; 2.1 3 57

97 49 44 041443 rolled contacts 0.14 - 1.5 26 - 15 3 45

97 49 50 030966 Coax connectors / Car phone RG 58, 174, 188, 3163.25; 4.52; 5.41; 1.72;

1.07

3.9, 5.4; 6.4; 2.1; 1.3; 0.95

6 48

97 49 54 041450 modular plugs 0.5 - 2.5 20 - 13 4 49

97 49 59 073734 solar cable connectors Helios H4 (Amphenol) 2.5 + 4.0 + 6.0 mm² 13 - 10 3 35

97 49 60 030928 turned contacts (HTS + Harting) 0.14 - 4.0 26 - 11 4 53

97 49 62 063179 solar cable connectors (Huber + Suhner) 2.5 + 4.0 13 + 11 3 41

97 49 63 066675 solar cable connectors (Huber + Suhner) 4.0 + 6.0 11 + 10 3 33

97 49 64 044055 ABS connectors 1.0 - 6.0 17 - 10 2 73

97 49 65 066682 solar cable connectors MC3 (Multi-Contact) 2.5 - 6.0 13 - 10 3 33

97 49 66 066699 solar cable connectors MC4 (Multi-Contact) 2.5 - 6.0 13 - 10 3 33

97 49 66 4 072096 solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping 4.0 11 1 35

97 49 66 6 072102 solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping 6.0 10 1 35

97 49 67 066705 solar cable connectors (Hirschmann) 2.5 - 6.0 13 - 10 3 33

97 49 68 066712 solar cable connectors (Tyco) 1.5 - 6.0 15 - 10 4 33

97 49 69 1 072119 solar cable connectors (Wieland) 1.5 - 2.5 15 + 13 2 35

97 49 69 2 072126 solar cable connectors (Wieland) 4.0 - 10.0 11 - 7 3 35

97 49 70 030942 Western plugs 4, 6, 8-poles RJ 10 / 11 /

12 / 45 3 72

97 49 74 044062 unshielded Molex plugs4, 6, 8-poles RJ 10 / 11 /

12 / 453 42

97 49 76 047513 shielded Stewart plugs 2 50

97 49 81 042778 Harting connectors for fibre optics 3.0; 4.95; 6.5

3.5; 6.0; 7.5 3 52

97 49 82 042785 Telegärtner connectors for fibre optics 3.25; 3.65; 4.52

3.6; 4.0; 5.4 3 58

136

CRIMPING PLIERS

97Locators for crimping pliers and crimping dies

Locator 97 59 65 2 for four-mandrel crimping pliers, adjustable in length and diameter for various plugs


Applications

g

97 49 59 1 073741 Locator for 97 49 59 55

97 49 65 1 066729 Locator for 97 49 65 (solar cable connectors MC3) 72

97 49 66 1 066736 Locator for 97 49 66 (solar cable connectors MC4) 72

97 49 68 1 066743 Locator for 97 49 68 (solar cable connectors Solarlok) 72

97 49 69 11 072133 Locator for 97 49 69 1 and 97 49 69 2 55

97 49 90 031017 Locator for 97 49 60 (HTS+Harting) 69

97 49 93 047926 Locator for 97 49 24 (D-Sub-plugs) 39

97 49 94 030997 Locator for 97 49 04 / 97 52 04 / 97 52 34 69

97 49 95 031000 Locator for 97 49 05 / 97 52 05 / 97 52 35 22

97 59 65 2 071600 Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A 237

97Mounting Tool for MC3 connectors

97 49 65 2

■ for easy and quick assembly of MC3 solar cable connectors

■ for fit solar sleeves for connectors from 2.5 to 10.0 mm²

■ three capsules (2.5 / 4.0; 6.0; 10.0 mm²) for pulling on the sleeves, integrated in the detachable handle

■ Body: plastic, fibreglass-rein-forced

The assembly tool comes with three torpedo mandrels for the various cable cross-sections


Capacitymm² g

97 49 65 2 072010 325 2.5 - 10.0 460

SOLAR TOOL

SOLAR TOOL

97Set of Mounting Tools

for solar cable connectors MC4 (Multi-Contact)

97 49 66 2

■ set of two mounting tools ■ to tighten cable glands of MC4 solar plugs■ to open the locking of MC4 housings

(even in case of mounted lock clip) ■ Tool: plastic, fibreglass reinforced

Article No. EAN4003773- mm g

97 49 66 2 074106 115 18

9749

97 49 83 044079 F-SMA, ST-,SC + STSC/K-connectors for fibre optics 3.65; 4.2; 5.0

4.3; 5.4; 6.0 3 60

97 49 84 042792 Harting/Suhner connectors for fibre optics 3.8; 4.3; 4.95

4.5; 5.2; 6.0 3 52

97 49 87 043331 F-SMA, ST and MIC connectors for fibre optics 8.7 9.5 1 46

Number of crimping positions g


Applications Capacitymm²

AWG Capacity SW mm

SleevesØ mm


Crimping Dies for Crimp System Pliers

137

CRIMPING PLIERS

9750 Crimping Pliers for Scotchlok

connectors with side cutter

97 50 01

■ for crimping plastic-insulated telecommunication or signal cables using the U-contact principle in single Scotchlok connectors

■ no stripping necessary, U-shaped elements establish the connection ■ cutting edges additionally induction hardened ■ with opening spring ■ Vanadium electric steel; forged, oil-hardened


Head Handles Applications CapacityØ mm g

97 50 01 028239 155 polished plastic coated Scotchlok single connector 0.4 - 1.1 135

9751 Crimping Pliers for Western plugs

97 51 04

■ for cutting and stripping unshielded ribbon telephone cables

■ for crimping 4-pole Western plugs type RJ 10 (7.65 mm wide)

■ Chrome vanadium electric steel in special quality, oil-hardened

Cut cables

Strip cables Crimp Western plugs




g

97 51 04 028048 190 burnished with plastic grips RJ 10 (4-poles) 7.65 mm 1 218

97 59 06 029700 4 spare blades for 97 51 04 / 97 51 10

138

CRIMPING PLIERS


97 51 10

■ professional tool for cutting and stripping unshielded ribbon telephone cables

■ for crimping 6- and 8-pole Western plugs type RJ 11/12 (9.65 mm width) and type RJ 45 (11.68 mm width)

■ exact crimping process due to parallel crimping

■ repetitive, high crimping quality due to integral lock (self-releasing mechanism)

■ with length cutter and dismant-ling knife for ribbon cables 6 and 12 mm length

■ with additional stripping device for round cables





g

97 51 10 043171 190 burnished with multi-component gripsRJ 11/12 (6-poles) 9.65 mm RJ 45

(8-poles) 11.68 mm 2 340

97 59 06 029700 4 spare blades for 97 51 04 / 97 51 10


97 51 12

■ professional tool for cutting and stripping unshielded ribbon telephone cables

■ for crimping 4-, 6- and 8-pole Western plugs type RJ 10 (7.65 mm width), type RJ 11/12 (9.65 mm width) and type RJ 45 (11.68 mm width)

■ exact crimping process due to parallel crimping

■ repetitive, high crimping quality due to integral lock (self-relea-sing mechanism)

■ optimum transmission of force due to toggle lever action for fatigue-reduced operation

■ with length cutter and dismant-ling knife for ribbon cables 6 and 12 mm length




g

97 51 12 043188 200 burnishedwith multi-compo-nent grips

RJ 10 (4-poles) 7.65 mm RJ 11/12 (6-poles) 9.65 mm RJ 45 (8-poles) 11.68 mm

3 522

97 59 12 069997 Spare blades for 97 51 12

■ with additional stripping device for round cables


139

CRIMPING PLIERS

9752 Crimping Pliers also for two-hand operation

97 52 04

97 52 06

97 52 09

97 52 10

■ for solder-free electrical connections ■ the ingenious lever transmission reduces the handforce up to 30 %

compared with regular crimping pliers ■ repetitive, high crimping quality due to precision dies and integral

lock (self-releasing mechanism) ■ crimping pressure has been set precisely (calibrated) in the factory,

re-adjustable ■ two-hand operation for easy crimping of large conductor diameters ■ easy handling as a result of well balanced centre of gravity, angled

head and ergnomically shaped handles ■ Chrome vanadium electric steel in special quality, oil-hardened

First step: move the handle with two fingers only until both jaws touch the connector to be crimped

Second step: now use the whole hand for further crimping procedure

Third step: when greater hand force is required, such as e.g. when crimping insulated connectors 6.0 mm², two-hand operation is possible by the longer handles




AWG

g

97 52 04 025450 250 burnishedwith non-slip plastic grips


0.1 - 2.5 27 - 13 4 562

97 52 05 025467 250 burnished with non-slip plastic grips


0.5 - 6.0 20 - 10 3 572



0.5 - 6.0 20 - 10 3 565


End Sleeves (ferrules) 0.25 - 6.0 23 - 10 5 565


End Sleeves (ferrules) 10 / 16

/ 25 7/ 5/ 3 3 571


Coax-, BNC- and TNC-connectors

3 577



0.5 - 10.0 20 - 7 4 558


End Sleeves (ferrules) 35 + 50 2 + 0 2 567



16 + 25 5 + 3 2 565

97 49 94 030997 Locator for 97 49 04 / 97 52 04 / 97 52 34

97 49 95 031000 Locator for 97 49 05 / 97 52 05 / 97 52 35

140

CRIMPING PLIERS

9752 Crimping Pliers short design

97 52 14

■ repetitive, high crimping quality due to precision dies and integral lock (self-releasing mechanism)

■ crimping pressure has been set precisely (calibrated) in the factory, re-adjustable

■ optimum transmission of force due to toggle lever action for fatigue-reduced operation

■ good handling due to 20° angled head, low weight and short design


97 52 14available as accessory: locator for non-insulated open plug-type connectors




AWG

g

97 52 14 026808 195 burnishedwith multi-compo-nent grips

non-insulated open plug type connectors (plug width 2.8 + 4.8 mm)

0.10 - 1.5 27 - 16 4 387

97 52 20 026853 195

burnished


Coax-, BNC- and TNC-connectors RG 58/59/62/71/223

3 380

97 59 14 026976 Locator for 97 52 14

141

CRIMPING PLIERS

9752 KNIPEX PreciForce® Crimping Pliers

97 52 34

97 52 36

97 52 38

For daily crimping applications, the specialist likes crimping pliers that work precisely and reliably. In addition, they should be light, comfortable to use, robust and reasonably priced: PreciForce®.



■ high transmission of force thanks to toggle lever action for fatigue-reduced working

■ good handling thanks to favourable handle position, low weight, compact design and ergonomically shaped handles


97 52 36 97 52 37




AWG

g


non-insulated butt connectors

1.5 - 4.0 6.0 + 10.0*

15 - 11 10 + 7

32 477


non-insulated terminals and plug connectors 0.5 - 10.0 20 - 7 4 478



0.1 - 2.5 27 - 13 4 483



0.5 - 6.0 20 - 10 3 494


insulated terminals and plug connectors 0.5 - 6.0 20 - 10 3 487


heat shrinkeable sleeve connectors 0.5 - 6.0 20 - 10 3 478

97 52 38 051909 220 burnished with multi-component grips End Sleeves (ferrules) 0.25 - 6.0 23 - 10 5 493


Coax-, BNC- and TNC-connectors for RG 58/174/188/316

6 498

97 49 94 030997 Locator for 97 49 04 / 97 52 04 / 97 52 34

97 49 95 031000 Locator for 97 49 05 / 97 52 05 / 97 52 35


142

CRIMPING PLIERS

9752 Four-Mandrel Crimping Pliers

for turned contacts

97 52 63 DG

97 52 64

97 52 65

97 52 65 DG

Turned contacts are used for particularly demanding plug-type connections, e.g. in medical industry and aeronautics. Extremely reliable crimping connections can be achieved only with pliers that work with absolute precision and maintain the required crimping depth in the 1/100 mm range.

■ for crimping turned contacts ■ four-mandrel crimping for top-quality crimping connections ■ mandrel gauge to check the basic setting ■ repetitive, high crimping quality due to integral lock

(self-releasing mechanism) ■ optimum transmission of force due to highly effective lever

action for fatigue-reduced operation ■ high operation comfort thanks to handy shape ■ Chrome vanadium electric steel in special quality, oil-hardened

97 52 63fine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; pliers in the plastic case with foam insert and standard locator for precise positioning of the contacts

97 52 63 DGfine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with digital display of the preset crimping capacities; display reversible between mm / inch and MIL numerical values; pliers in a plastic case with foam insert and standard locator for precise positioning of the contacts

97 52 64pressure adjustment depending on the conductor‘s diameter by means of adjusting wheel in 4 different positions; locator for positioning the contacts

97 52 65fine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; locator for positioning the contacts; with table for calculating the settings; pliers in a plastic case with foam insert

97 52 65 DGfine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with digital display of the preset crimping capacities; display reversible between mm / inch and MIL numerical values; with table for calculating the settings; pliers in a plastic case with foam insert and standard locator for precise positioning of the contacts

97 52 65 Afine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with table for calculating the settings; pliers in a plastic case with foam insert

97 52 65 DG Afine adjustment of pressure depending on the conductor‘s diameter by means of adjusting wheel; with digital display of the preset crimping capacities; display reversible between mm / inch and MIL numerical values; with table for calculating the settings; pliers in a plastic case with foam insert; without locator

97 59 65 2Universal Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A; Chrome vanadium electric steel in special quality, oil-hardened■ locator that is universally adjustable (in length and diameter) for the repeatable

exact alignment of turned contacts in crimping pliers; can be set to all commercially available contacts in the four-mandrel crimping pliers‘ capacity range

97 59 65 2

143




AWG

g

97 52 63 050148 180 nickel plated


turned contacts 0.08 - 2.5 28 - 13 1 388

97 52 63 DG 063209 195

nickel plated


turned contacts 0.08 - 2.5 28 - 13 1 388

97 52 64 044093 180 nickel plated


turned contacts 0.08 - 2.5 28 - 13 1 424

97 52 65 045236 230

nickel plated


turned contacts (Harting; Ilme; Phoenix; Amphenol; Walther; HTS; Contact; Weidmüller)

0.14 - 6.0 25 - 10 1 676

97 52 65 DG 063216 250 nickel plated



0.14 - 6.0 25 - 10 1 633

97 52 65 A 071594 250

nickel plated



0.14 - 6.0 25 - 10 1 604

97 52 65 DG A 071990 250 nickel plated



0.14 - 6.0 25 - 10 1 633

97 59 65 2 071600 Universal Locator for 97 52 65 / 97 52 65 A / 97 52 65 DG / 97 52 65 DG A

Standard locator

CRIMPING PLIERS

144

CRIMPING PLIERS

9753 Self-Adjusting Crimping Pliers for

end sleeves (ferrules) with lateral access

97 53 04

97 53 14

Compact crimping pliers for end sleeves (ferrules) with two great advantages for the user: - Automatic self-adjustment to the end sleeve (ferrule)

used: this allows the specialist to work with less strain and enables secure, reliable and quick crimping.

- Extensive range of applications: square crimping 0.08 to 10.0 mm², hexagon crimping 0.08 to 6.0 mm²

■ for crimping end sleeves (ferrules) according to DIN 46228 parts 1 + 4

■ self-adjusting adaptation to the desired end sleeve (ferrule) size: no wrong crimps caused by using the wrong die

■ fits all twin ferrules within the application range■ lateral access of the end sleeves (ferrules) into the tool ■ repetitive, high crimping quality due to integral lock

(self-releasing mechanism) ■ these tools have been set precisely (calibrated) in the factory,

re-adjustable ■ optimum transmission of force due to toggle lever action for

fatigue-reduced operation ■ high operation comfort thanks to handy shape and low weight ■ Chrome vanadium electric steel in special quality, oil-hardened

97 53 04square crimping for optimum contact areas in the clamp connection

97 53 14hexagonal crimping for optimum positioning in confined areas

The square crimping allows better contact. The hexagonal crimping comes very close to the space-saving round shape. Compared with the square crimp, it has the same cross-section and can make optimum contact in narrow round terminal connec-tors. With both crimping shapes the often tricky feeding into the terminal connection is no longer necessary.

Square-crimped end sleeves (ferrules) always ensure good contact surfaces in the clamped connection




AWG

g

97 53 04 028017 180 burni-shed


End Sleeves (ferrules)

0.08 - 10 28 - 7 1 405

97 53 14 041474 180 burni-shed



0.08 - 6.0 28 - 10 1 404

145

CRIMPING PLIERS

9753 Self-Adjusting Crimping Pliers for

end sleeves (ferrules) with front loading

97 53 08

97 53 09

The crimping pliers for end sleeves (ferrules) with three great advantages for the user: - Automatic self-adjustment to the end sleeve (ferrule)

used: This allows the specialist to work with less strain and enables secure, reliable and quick crimping.

- Range of applications also for large cross-sections: square crimping 0.08 to 10.0 + 16.0 mm²

- Front loading: very helpful under difficult working conditions in confined spaces.

■ for crimping end sleeves (ferrules) according to DIN 46228 parts 1 + 4

■ self-adjusting adaptation to the desired end sleve (ferrule) size: no wrong crimps caused by using the wrong die

■ fits all twin-ferrules within the application range■ front loading of the end sleeves (ferrules) into the tool ■ repetitive, high crimping quality due to integral lock (self-releasing

mechanism) ■ crimping pressure has been set precisely (calibrated) in the factory,

re-adjustable ■ optimum transmission of force due to toggle lever action for

fatigue-reduced operation ■ high operation comfort thanks to handy shape and low weight ■ Chrome vanadium electric steel in special quality, oil-hardened

97 53 08crimping from 0.08 - 10.0 mm² in one profile; end sleeves (ferrules) up to 2.5 mm² can also be loaded parallely from the side

97 53 09crimping from 0.08 - 10.0 and 16.0 mm² in one profile; with selector lever for setting the crimping area either to 0.08 - 10 mm² or 16 mm²

Front loading of end sleeves (ferrules) e.g. in switchboards

Square crimping

97 53 08: lateral loading of end sleeves (ferrules) up to 2.5 mm² parallely from the side e.g. in confined areas




AWG

g

97 53 08 040187 190 burni-shed



0.08 - 10 28 - 7 1 477

97 53 09 044550 190 burni-shed



0.08 - 10 + 16 28 - 7 + 5 1 486

146

CRIMPING PLIERS

9754 Crimping Pliers for micro plugs

parallel crimping

97 54 24

■ parallel crimping performance to satisfy the particularly high standards of small connectors


■ fixed locator for D-Sub micro plugs for an exact positioning of connector and cable


■ optimum transmission of force due to toggle lever for fatigue-reduced operation




AWG

g


D Sub; HD 20; HDE plug

0.03 - 0.56 32 - 20 3 305

■ crimping pliers for other mini plugs as e.g. HD 22, Modu IV, Micro Timer, MQS, ... on request



(ferrules)

97 62 145 A

97 68 145 A

■ for crimping end sleeves (ferrules) according DIN 46228 parts 1 + 4 in the range from 0.25 up to 2.5 mm²

■ crimping in marked trapezoidal dies for reliable connections between the sleeve and the conductor

■ Vanadium electric steel; forged, oil-hardened



Head Handles Capacitymm²

AWG

g

97 61 145 A 035558 145 polished plastic coated 0.25 - 2.5 23 - 13 6 140

97 61 145 F 043980 145 polished plastic coated 0.25 - 2.5 23 - 13 6 140

97 62 145 A 060154 145 polished with multi-component grips 0.25 - 2.5 23 - 13 6 170

97 68 145 A 071754 145

polished insulated with multi-component grips, VDE-tested

0.25 - 2.5 23 - 13 6 175

147

CRIMPING PLIERS


(ferrules)

97 71 180

97 72 180

■ for crimping end sleeves (ferrules) according DIN 46228 parts 1 + 4 from 0.25 to 16 mm²

■ crimping in marked half-round dies for reliable connections between the sleeve and the conductor

■ 9 particularly deep dies with conical side faces ■ Special tool steel, forged, oil-hardened



Head Handles Applications Capacitymm²

AWG

g

97 71 180 040668 180 polished plastic coated End Sleeves (ferrules) 0.25 - 16.0 23 - 5 9 240

97 72 180 060185 180 polished with multi-component grips End Sleeves (ferrules) 0.25 - 16.0 23 - 5 9 283


(ferrules) with front loading

97 81 180

■ for crimping end sleeves (ferrules) according DIN 46228 parts 1 + 4 in the range 0.5 to 6.0 mm²

■ ideal for work in confined areas, e.g. in narrow and deep switch boxes

■ Special tool steel, forged, oil-hardened



Head Handles Applications Capacitymm²

AWG

g

97 81 180 019794 180 polis-hed

plastic coated End Sleeves (ferrules) 0.5 - 6.0 20 - 10 1 227

148

CRIMP ASSORTMENTS

9790 Crimp Assortments for cable connectors

97 90 00 97 90 01

97 90 21 97 90 22

in a TANOS MINI-systainer® (solid plastic box) two stackable plastic inserts with 6 trays each for connectors with an assortment of standard cable connectors

97 90 00with Crimp Grip Pliers 97 00 215 A

97 90 01with Crimping Pliers 97 32 225

97 90 21with Crimping Pliers ”PreciForce“ 97 52 36 (for insulated terminals and plug connectors)

97 90 22with Self-Adapting Universal Insulation Stripper ”Multistrip 10“ 12 42 195; with Crimping Pliers ”PreciForce“ 97 52 36 (for insulated terminals and plug connectors)

Cable ConnectorsArticle No. EAN

4003773-Pliers Units Cable

mm² g

97 90 00 025375 97 00 215 A

Female Sockets 6.0 x 0.8 mm² 25 0.5 - 1.0

1391Female Sockets 6.0 x 0.5 mm² 25 1.5 - 2.5Female Sockets 8.0 x 0.8 mm² 25 1.5 - 2.5Round Sockets 4.0 mm Ø 25 0.5 - 1.0Round Pin Plugs 4.0 mm Ø 25 1.5 - 2.5Cable Connectors, eye type 4.0 mm Ø 25 0.5 - 1.0

97 90 01 025382 97 32 225

Cable Connectors, eye type 4.0 mm Ø 25 1.5 - 2.5

1123 Cable Connectors, eye type 5.0 mm Ø 25 1.5 - 2.5Cable Connectors, eye type 5.0 mm Ø 25 4.0 - 6.0Cable Connectors, eye type 6.0 mm Ø 25 4.0 - 6.0Insulated Butt Connectors 25 0.5 - 1.0Insulated Butt Connectors 25 1.5 - 2.5

97 90 21 062134 97 52 36

Female Sockets 6.0 x 0.8 mm² 25 0.5 - 1.0

1416Female Sockets 6.0 x 0.5 mm² 25 1.5 - 2.5Cable Connectors, eye type 4.0 mm Ø 25 0.5 - 1.0Cable Connectors, eye type 5.0 mm Ø 25 0.5 - 1.0Cable Connectors, eye type 5.0 mm Ø 20 4.0 - 6.0Cable Connectors, eye type 4.0 mm Ø 25 1.5 - 2.5

97 90 22 062141 97 52 36 12 42 195

Cable Connectors, eye type 5.0 mm Ø 25 1.5 - 2.5

1527 Cable Connectors, eye type 6.0 mm Ø 25 1.5 - 2.5Cable Connectors, eye type 8.0 mm Ø 20 4.0 - 6.0Insulated Butt Connectors 25 0.5 - 1.0Insulated Butt Connectors 25 1.5 - 2.5Insulated Butt Connectors 20 4.0 - 6.0

149


Pliers 200 xmm²

150 xmm²

100 xmm²

75 xmm²

50 xmm²

40 xmm² g

97 90 05 025535 97 71 1800.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 10.0 / 16.0 930

97 90 06 025542 97 71 1800.5 / 0.75 /

1.0 / 1.5 2.5 4.0 / 6.0 10.0 16.0

1000

97 90 09 028574 97 53 04 0.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 10.0 1420

97 90 10 046202 97 53 04 / 12 40 2000.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 10.0 1353

97 90 12 048916 97 53 08 / 12 40 2000.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 10.0 1427

97 90 23 062158 97 52 380.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 1226

97 90 24 062394 97 53 08 / 12 42 195 0.5 / 0.75 / 1.0 / 1.5 /

2.54.0 / 6.0 10.0 1348

9790 Crimp Assortments for end sleeves (ferrules)

97 90 05

in a TANOS MINI-systainer® (solid plastic box) two stackable plastic inserts with 6 trays each for connectors with an assortment of standard cable connectors

97 90 05with Crimping Pliers for end sleeves 97 71 180; end sleeves (ferrules) without collar

97 90 06with Crimping Pliers for end sleeves 97 71 180; End Sleeves (ferrules) with collar

97 90 09with Self-Adjusting Crimping Pliers for End Sleeves (ferrules) 97 53 04

97 90 10with Self-Adjusting Insulation Stripper 12 40 200; with Self-Adjusting Crimping Pliers for End Sleeves (ferrules) 97 53 04

97 90 12with Self-Adjusting Insulation Stripper 12 40 200; with Self-Adjusting Crimping Pliers for End Sleeves (ferrules) 97 53 08

97 90 23with Crimping Pliers ”PreciForce“ for End Sleeves (ferrules) 97 52 38

97 90 24with Self-Adapting Universal Insulation Stripper ”Multistrip 10“ 12 42 195; with Self-Adjusting Crimping Pliers for End Sleeves (ferrules) 97 53 08

Several boxes can be connected with each other

CRIMP ASSORTMENTS

97 90 06

97 90 09 97 90 10

97 90 12 97 90 23 97 90 24

150

CRIMP ASSORTMENTS

9791 Tool Case for Photovoltaics

97 91 01

with tools for photovoltaics without crimping dies – for individual equipment – please order separately (see ref. 97 49 ...) with service tools (hexagonal key) for the change of crimping dies shock-resistant plastic case foam insert with recesses for tools, crimping dies and locators external dimensions (W x H x D): 345 x 80 x 280 mm


Units

g

97 91 01

070351

Tool Case for Photovoltaics 1964 12 12 11 Precision Insulation Stripper with shaped blades 195 16 165 Cable Shears 1 97 43 200 Crimp System Pliers 1

not included (please order separately):

97 49 62 063179 Crimping dies for solar cable connectors (Huber + Suhner)

97 49 63 066675 Crimping dies for solar cable connectors (Huber + Suhner)

97 49 65 066682 Crimping dies for solar cable connectors MC3 (Multi-Contact)

97 49 65 1 066729 Locator for 97 49 65 (solar cable connectors MC3)

97 49 65 2 072010 Mounting Tool for MC3 connectors

97 49 66 066699 Crimping dies for solar cable connectors MC4 (Multi-Contact)

97 49 66 1 066736 Locator for 97 49 66 (solar cable connectors MC4)

97 49 66 4 072096 Crimping dies for solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping

97 49 66 6 072102 Crimping dies for solar cable connectors MC4 (Multi-Contact) cutting - stripping - crimping

97 49 67 066705 Crimping dies for solar cable connectors SunCon (Hirschmann)

97 49 68 066712 Crimping dies for solar cable connectors Solarlok (Tyco)

97 49 68 1 066743 Locator for 97 49 68 solar cable connectors (Solarlok)

97 49 69 1 072119 Crimping dies for solar cable connectors gesis® PST 40 (Wieland)

97 49 69 2 072126 Crimping dies for solar cable connectors gesis® PST 40 (Wieland)

97 49 69 11 072133 Locator for 97 49 69 1 and 97 49 69 2

97 49 59 073734 Crimping dies for solar cable connectors Helios H4 (Amphenol)

151

9791 Tool Case for Photovoltaics, MC3

(Multi-Contact)

97 91 02

the complete tool set to install MC3 connectors shock-resistant plastic case foam insert with recesses for the tools, crimping dies and locators with four empty plastic boxes for consumables for individual equipping dimensions, exterior (W x H x D): 360 x 105 x 300 mm


Units

g

97 91 02

074083

Tool Case for Photovoltaics, MC3 (Multi-Contact) 3280

12 12 11 Precision Insulation Stripper with shaped blades 195 16 165 Cable Shears 1 97 43 200 Crimp System Pliers 197 49 65 Crimping dies for solar cable connectors MC3 (Multi-Contact) 1 97 49 65 1 Locator for 97 49 65 (solar cable connectors MC3) 197 49 65 2 Mounting Tool for MC3 connectors 1

97 91 02 LE 074090 Tool Case for Photovoltaics, MC3 (Multi-Contact) empty

CRIMP ASSORTMENTS

152

CABLE CONNECTORS

9799

Width x Thickness

mm²


Designation PlugØ mm

ScrewsØ mm

Cablemm²

AWG Colour Quantity

97 99 01 025559 Blade Terminal Sockets 6.3 x 0.8 0.5 - 1.0 20 - 17 red 75 97 99 02 025566 Blade Terminal Sockets 6.3 x 0.8 1.5 - 2.5 15 - 13 blue 5097 99 03 025573 Blade Terminal Sockets 6.3 x 0.8 4.0 - 6.0 11 - 10 yellow 25 97 99 04 025580 Blade Terminal Sockets 8.0 x 0.8 1.5 - 2.5 15 - 13 blue 5097 99 05 025597 Blade Terminal Plugs 6.3 x 0.8 0.5 - 1.0 20 - 17 red 75 97 99 06 025603 Blade Terminal Plugs 6.3 x 0.8 1.5 - 2.5 15 - 13 blue 7597 99 07 025610 Round Sockets 4.0 0.5 - 1.0 20 - 17 red 25 97 99 08 025627 Round Sockets 5.0 1.5 - 2.5 15 - 13 blue 2597 99 09 025634 Round Pin Plugs 4.0 0.5 - 1.0 20 - 17 red 75 97 99 10 025641 Round Pin Plugs 5.0 1.5 - 2.5 15 - 13 blue 5097 99 11 025658 Flat Pin Accessory Distributors 6.3 x 0.8 0.5 - 1.0 20 - 17 red 25 97 99 12 025665 Flat Pin Accessory Distributors 6.3 x 0.8 1.5 - 2.5 15 - 13 blue 2597 99 13 025672 Cable Connectors, eye type 3 0.5 - 1.0 20 - 17 red 100 97 99 14 025689 Cable Connectors, eye type 4 0.5 - 1.0 20 - 17 red 10097 99 15 025696 Cable Connectors, eye type 5 0.5 - 1.0 20 - 17 red 100 97 99 16 025702 Cable Connectors, eye type 4 1.5 - 2.5 15 - 13 blue 10097 99 17 025719 Cable Connectors, eye type 5 1.5 - 2.5 15 - 13 blue 50 97 99 18 025726 Cable Connectors, eye type 6 1.5 - 2.5 15 - 13 blue 5097 99 19 025733 Cable Connectors, eye type 8 1.5 - 2.5 15 - 13 blue 50 97 99 20 025740 Cable Connectors, eye type 5 4.0 - 6.0 11 - 10 yellow 2597 99 21 025757 Cable Connectors, eye type 6 4.0 - 6.0 11 - 10 yellow 25 97 99 22 025764 Cable Connectors, eye type 8 4.0 - 6.0 11 - 10 yellow 2597 99 23 025771 Cable Connectors, eye type 10 4.0 - 6.0 11 - 10 yellow 25 97 99 24 025788 Cable Connectors, forked 4 0.5 - 1.0 20 - 17 red 10097 99 25 025795 Cable Connectors, forked 4 0.5 - 1.0 20 - 17 red 100 97 99 26 025801 Cable Connectors, forked 5 0.5 - 1.0 20 - 17 red 7597 99 27 025818 Cable Connectors, forked 4 1.5 - 2.5 15 - 13 blue 75 97 99 28 025825 Cable Connectors, forked 5 1.5 - 2.5 15 - 13 blue 5097 99 29 025832 Cable Connectors, forked 5 4.0 - 6.0 11 - 10 yellow 25 97 99 30 025849 Cable Connectors, forked 6 4.0 - 6.0 11 - 10 yellow 2597 99 31 025856 Round Pattern Cable Connectors 0.5 - 1.0 20 - 17 red 100 97 99 32 025863 Round Pattern Cable Connectors 1.5 - 2.5 15 - 13 blue 10097 99 33 025870 Round Pattern Cable Connectors 4.0 - 6.0 11 - 10 yellow 25 97 99 34 025887 insulated Butt Connectors 0.5 - 1.0 20 - 17 red 5097 99 35 025894 insulated Butt Connectors 1.5 - 2.5 15 - 13 blue 50 97 99 36 025900 insulated Butt Connectors 4.0 - 6.0 11 - 10 yellow 25

97 99 37 025917 Two-Way-Sockets 6.3 - 0.8 25

97 99 38 025924 Piggyback Disconnect 6.3 - 0.8 50

97 99 40 025931 End Sleeves (ferrules) 0.5 20 200 97 99 41 025948 End Sleeves (ferrules) 0.75 18 20097 99 42 025955 End Sleeves (ferrules) 1.0 17 200 97 99 43 025962 End Sleeves (ferrules) 1.5 15 20097 99 44 025979 End Sleeves (ferrules) 2.5 13 200 97 99 45 025986 End Sleeves (ferrules) 4.0 11 15097 99 46 025993 End Sleeves (ferrules) 6.0 10 150 97 99 47 026006 End Sleeves (ferrules) 10.0 7 5097 99 48 026013 End Sleeves (ferrules) 16.0 5 50 97 99 49 026020 End Sleeves (ferrules) 25.0 3 5097 99 70 024248 End Sleeves (ferrules) with collar 0.5 20 white 200 97 99 71 024255 End Sleeves (ferrules) with collar 0.75 18 grey 20097 99 72 024262 End Sleeves (ferrules) with collar 1.0 17 red 200 97 99 73 024279 End Sleeves (ferrules) with collar 1.5 15 black 20097 99 74 024286 End Sleeves (ferrules) with collar 2.5 13 blue 200 97 99 75 026037 End Sleeves (ferrules) with collar 4.0 11 grey 15097 99 76 026044 End Sleeves (ferrules) with collar 6.0 10 yellow 150 97 99 77 026051 End Sleeves (ferrules) with collar 10.0 7 red 5097 99 78 026068 End Sleeves (ferrules) with collar 16.0 5 blue 50 97 99 79 026075 End Sleeves (ferrules) with collar 25.0 3 yellow 5097 99 92 031123 non-insulated Blade Terminal Sockets 2.8 - 1.5 15 150 97 99 93 031130 non-insulated Blade Terminal Sockets 4.8 - 1.5 15 15097 99 95 031147 non-insulated Blade Terminal Sockets 6.3 - 1.5 15 100 97 99 96 031154 non-insulated Blade Terminal Sockets 6.3 - 2.5 13 100

VDE PLIERS HANDLES:IMPROVED COMFORT DESIGN.

distinctive VDE design

rounded collar edges reduce uncomfortable pressure points

recess in the collar to facilitate a precise and steady pliers guidance

durable injection-moulded marking

optimised arrangement of the soft and hard components

yellow, softer material for a better grip when force is applied

red, harder material reduces friction when the grips neet to slide in the hand

INSULATED TOOLSWork on electrical installations is subject to the special protection tasks of authorities and insurance companies. This resulted in the creation of diverse national and international safety standards (e.g. in Germany the VDE 0105 and BGR A3, internationally EN 50110 or IEC 60364). Only a qualified electrician who respects and follows these regulations is permitted to carry out work on electrical installations (including live working). He has to use special tools for this particular work that have been specifically made for this kind of work and have been thoroughly tested.

KNIPEX insulated tools are made of high-quality materials, which have been manufactured and tested in conformance with the re-gulations of national and international standards. If the prescribed method for working on electrical installations (see above), are ob-served, these tools offer the greatest possible protection even when it is necessary to work live up to AC 1000 V (alternating current) and DC 1500 V (direct current).

Since 1987 the IEC 60900 has specified worldwide requirements for tools for live working, while DIN EN 60900 made these mandatory for the EU countries as from 1995. Tests on KNIPEX tools which bear the special mark include subjecting them to routine tests with 10,000 volts to check their dielectric strength. This gives the user a considerable buffer of additional protection even if work on electrical installations needs to be performed live.

The mark identifies KNIPEX insulated tools as being sui-table for live working. The specified standard also shows the re-quirements our claim can be measured against. The manufacturer name KNIPEX on the insulation indicates that we accept responsi-bility for the correctness of this information. The marks prove: The observation of these requirements is monitored not only by the KNIPEX quality assurance team but also e.g. by VDE (Association of German Electricians).

Because the purchase of insulated hand tools is a matter of trust.

Type examination, manufac-turing inspections and stock monitoring by the neutral VDE testing centre.

COVER INSULATION(VERSION 6)

KNIPEX pliers with the two-colour multi-component handle cover insulation meet the requirements of VDE 0682 Part 201 and corres-ponding international standards (e.g. EN 60900 or IEC 60900). This claim is confirmed by the VDE/GS mark awarded by an obligatorily neutral inspection body.

The slip guard is designed so that the hand cannot slip unintentionally on conductive metal parts on the head of the pliers.

DIPPED INSULATION(VERSION 7)Other hand tools such as open ended spanners/ single ended box wrenches, socket wrenches, ratchets etc. are insulated at KNIPEX using a plastic dipping method. These also meet all requirements of the VDE standard and corresponding international standards (such as IEC 60900 or DIN EN 60900). To round off this range, KNIPEX also insulates pliers in a dipping process to adapt these tools con-cerning appearance and production method to the other dipped in-sulated tools. These pliers also bear the VDE/GS mark.

The firmly bonded double dipped insulation is made of insulating material which is free of harmful substances and more than 1 mm thick at each point.

Extra thick insulation at the ends of the handles. This prevents cracks following an impact.

Insulated tools must be transported in a manner that will prevent any damage to the insulation.Check before every use whether the insulation is damaged in any way, defective tools must be discarded.Always keep your insulated tools clean and dry.Wear protective goggles when working with cutting nippers or working overhead.Always wear goggles or a facial mask when working on live equipment.

Make sure the workplace is clean and orderly, particularly when you are working on live installations.Wear protective clothing and use SAFETY equipment (e.g. insulating gloves, insulating mats, protective covers) especially in confined working spaces.Use only a tool with suitable dimensions. That will prevent slipping on the workpiece and unintentional contact with non-insulated parts.Make sure that detached parts or cut-off ends of conductors do not fall onto live parts.

Always comply with the currently valid regulations and observe the SAFETY INSTRUCTIONS given below:

154

KNIPEX INSULATED TOOLS – 100 % TESTED, ONE BY ONE

Testing dielectric strength Testing the adhesion of the insulating coating

Each KNIPEX insulated tool has been tested individually. This individual testing is done with a test voltage of AC 10,000 volts. This test load, which is 10 times as high as the maximum permitted voltage during work, inspires the user to trust a reliable insulation when live working.

The adhesion of the insulation coating is tested after storage of 168 hours at 70°C. In case of pliers a tensile load of 500 N is applied. The insulating material must remain firmly bonded to the basic tool.

Testing low temperature impact strength Testing burning behaviour

The tools are cooled down to -25°C. The insulation material must retain the toughness necessary to ensure that it does not break when hit or knocked.

KNIPEX uses only flame-resistant and self-extinguishing plastics for insulation.

Testing electrical insulation Testing indentation resistance

After submersion in water for 24 hours, the tools are tested with AC 10,000 V for 3 minutes including measuring of the leakage current. The reading of the leakage current must stay below the limits defi-ned in the standards.

The insulation heated to 70°C must prove under standardised test conditions that the warm plastic has sufficient mechanical strength to resist expected loads.

155

156

INSULATED TOOLS

01Combination Pliers Chrome Vanadium


01 06 190

for heaviest duty with gripping zones for flat and round material, suitable for versatile use with cutting edges for soft, hard and piano wire long cutting edges for thicker cables cutting edges additionally induction hardened, cutting edge hardness approx. 64 HRC particularly wear resistant gripping jaws; hardness of the gripping jaws approx. 53 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened


4003773- mm

Pliers Handles


01 06 160 040729 160

chrome plated


2.0 1.5 10.0 16.0 220

01 06 190 040415 190 2.5 2.0 13.0 25.0 320

02High Leverage Combination Pliers DIN ISO 5746 IEC 60900 DIN EN 60900

02 06 180

02 07 225

35 % saving in power due to improved lever action compared with conventional combination pliers easier work due to optimised leverage with cutting edges (hardness approx. 63 HRC) for soft and hard wire and piano wire long cutting edges for thicker cables with gripping zones for flat and round material, suitable for versatile use High-grade special tool steel, forged, oil-hardened


4003773- mm

Pliers Handles


02 06 180 010012 180

chrome plated


2.5 2.0 11.5 16.0 247

02 06 200 010029 200 2.8 2.2 13.0 25.0 343

02 06 225 010036 225 3.0 2.5 14.0 25.0 401

02 07 200 022299 200

chrome plated

with dipped insulation, VDE-tested 2.8 2.2 13.0 25.0 380

02 07 225 022305 225 3.0 2.5 14.0 25.0 486

157

INSULATED TOOLS

03Combination Pliers DIN ISO 5746 IEC 60900 DIN EN 60900

03 06 180

03 07 200

with gripping zones for flat and round material, suitable for versatile use with cutting edges for soft and hard wire long cutting edges for thicker cables cutting edges additionally induction hardened, cutting edge hardness approx. 60 HRC Special tool steel, forged, oil-hardened


4003773- mm

Pliers Handles


03 06 160 021902 160

chrome plated


3.1 2.0 10.0 16.0 228

03 06 180 021926 180 3.4 2.2 12.0 16.0 264

03 06 200 033776 200 3.8 2.5 13.0 16.0 326

03 07 160 015307 160

chrome plated

with dipped insulation, VDE-tested

3.1 2.0 10.0 16.0 254

03 07 180 015314 180 3.4 2.2 12.0 16.0 285

03 07 200 015321 200 3.8 2.5 13.0 16.0 339

03 07 250 015345 250 3.8 2.5 15.0 25.0 597


11 06 160

11 07 160

for single, multiple and fine stranded conductors with plastic or rubber insulation max. 5.0 mm dia. or resp. 10.0 mm² cable cross section easy adjustment to the required diameter of solid or stranded wire with knurled screw and lock nut Special tool steel, forged, oil-hardened


Pliers Handles Stripping capacities

Ø mm

Stripping capacities

mm²

AWG

g

11 06 160 021933 160 chrome plated


5.0 10.0 7 166

11 07 160 015499 160 chrome plated

with dipped insulation, VDE-tested 5.0 10.0 7 180

11 17 160 015505 160 chrome plated

with dipped insulation, VDE-tested 5.0 10.0 7 181

IEC 60900 DIN EN 60900

158

INSULATED TOOLS

14Diagonal Insulation Stripper IEC 60900 DIN EN 60900

14 26 160

the essential pliers for electrical installation work precision stripping holes for single (solid) conductors of 1.5 and 2.5 mm² induction hardened precision blades for soft wire up to 4.0 mm dia., cutting edge hardness approx. 60 HRC Vanadium electric steel; forged, oil-hardened

Multi-functional: cutting and stripping


4003773- mm

Pliers Handles Stripping capacities

mm²

AWG

Ø mm Ø mm g

14 26 160 040279 160 chrome plated

insulated with multi-compo-nent grips, VDE-tested

1.5 + 2.5 15 + 13 2.5 1.5 216

20Flat Nose Pliers DIN ISO 5745 IEC 60900 DIN EN 60900

20 06 160

short, flat jaws serrated gripping surfaces Chrome vanadium electric steel, forged, oil-hardened


4003773- mm

Pliers Handles L3mm

W3mm

T1mm g

20 06 160 033783 160 chrome plated


30.0 17.0 9.5 176

159

INSULATED TOOLS

22Round Nose Pliers DIN ISO 5745 IEC 60900 DIN EN 60900

22 06 160

22 07 160

for bending wire loops precision ground, short, round jaws smooth tips Chrome vanadium electric steel, forged, oil-hardened


4003773- mm

Pliers Handles L3mm

W3mm

D1mm

T1mm g

22 06 160 033790 160 chrome plated


30.0 18.0 3.0 9.5 175

22 07 160 015901 160 chrome plated

with dipped insulation, VDE-tested 30.0 18.0 3.0 9.5 196

25Snipe Nose Side Cutting Pliers (Radio Pliers)


25 06 160

25 26 160

40°

suitable for finer gripping and cutting work pointed, half-round jaws serrated gripping surfaces with cutting edges for medium hard and hard wire cutting edges additionally induction hardened, cutting edge hardness approx. 61 HRC Vanadium electric steel; forged, oil-hardened


4003773- mm

Pliers Handles

Ø mm Ø mm

L3mm

L4mm

W3mm

T1mm

W4mm

T2mm g

25 06 160 033806 160

chrome plated


2.5 1.6 50.0 16.5 9.0 3.0 2.5 146

25 26 160 052111 160

40°

chrome plated


2.5 1.6 50.0 23.0 16.5 9.0 3.0 2.5 144

160

INSULATED TOOLS

26Snipe Nose Side Cutting Pliers (Stork Beak Pliers)


26 16 200

26 27 200

40°

high loadable, elastic precision points half-round, long jaws serrated gripping surfaces with cutting edges for medium hard wire max. dia. 3.2 mm and hard wire max. dia. 2.2 mm cutting edges additionally induction hardened, cutting edge hardness approx. 61 HRC Vanadium electric steel; forged, oil-hardened


4003773- mm

Pliers Handles

Ø mm Ø mm

L3mm

L4mm

T1mm

W3mm

W4mm

T2mm g

26 16 200 022831 200

chrome plated


3.2 2.2 73.0 9.5 17.5 3.0 2.5 206

26 17 200 016069 200

chrome plated


3.2 2.2 73.0 9.5 17.5 3.0 2.5 212

26 26 200 022855 200

40° chrome plated


3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 204

26 27 200 016090 200

40°

chrome plated


3.2 2.2 73.0 23.0 9.5 17.5 3.0 2.5 220

30Long Nose Pliers DIN ISO 5745 IEC 60900 DIN EN 60900

30 16 160

30 36 160

heavy duty and wear resisting different jaw styles Chrome vanadium electric steel, forged, oil-hardened

Style 1long, trapezoidal jaws; knurled gripping surfaces

Style 3long, round jaws; smooth gripping surfaces


4003773- mm

Style Pliers Handles L3mm

W3mm

T1mm

W4mm

T2mm g

30 16 160 001904 160 1chrome plated


46.5 16.5 9.5 3.0 5.0 150

30 36 160 002123 160 3 chrome plated


41.0 16.5 9.5 5.0 2.5 141

161

INSULATED TOOLS

70Diagonal Cutters DIN ISO 5749 IEC 60900 DIN EN 60900

70 06 160

70 07 160

20 % less effort requiredcompared to conventional diagonal cutters of the same length. With integrated forged joint axle.

the indispensable diagonal cutter for all-round use high quality material and precise workmanship for long service life precision cutting edges for soft and hard wire clean cutting of thin copper wires, also at the cutting-edge tips precision cutting edges additionally induction hardened, cutting edge hardness approx. 62 HRC narrow head style for use in confined areas Vanadium electric steel; forged, oil-hardened

Slim head style and precise cut at blade tips: Advantageous when working in confined areas


4003773- mm

Pliers Handles

Ø mm Ø mm Ø mm g

70 06 125 018124 125

chrome plated


3.0 2.3 1.5 121

70 06 140 040293 140 4.0 2.5 1.8 160

70 06 160 021995 160 4.0 2.8 2.0 216

70 06 180 033813 180 4.0 3.0 2.5 254

70 07 160 018155 160

chrome plated

with dipped insulation, VDE-tested 4.0 2.8 2.0 227

70 07 180 018179 180 4.0 3.0 2.5 269

70 26 160 018223 160 chrome plated

insulated with multi-component grips, VDE-tested 4.0 2.8 1.8 216

74High Leverage Diagonal Cutters

74 06 200

74 07 200

with forged-in axle for heaviest duty suitable for all types of wire including piano wire high cutting performance with minimum effort due to optimum coordination of the cutting edge angle, transmission ratio and ergonomic handle shape precision cutting edges additionally induction-hardened, cutting edge hardness approx. 64 HRC Chrome vanadium heavy-duty steel, forged, oil-hardened


4003773- mm

Pliers Handles

Ø mm Ø mm Ø mm g

74 06 160 040705 160

chrome plated


3.4 2.5 2.0 215

74 06 180 022985 180 3.8 2.7 2.2 28074 06 200 033820 200 4.2 3.0 2.5 308 74 06 250 041955 250 4.6 3.5 3.0 45374 07 200 018414 200

chrome plated

with dipped insulation, VDE-tested 4.2 3.0 2.5 328

74 07 250 018421 250 4.6 3.5 3.0 510


162

INSULATED TOOLS

8607 Pliers Wrench insulated

IEC 60900 DIN EN 60900

86 07 250

pliers and wrench in a single tool also excellent for gripping, holding, pressing and bending workpieces zero backlash jaw pressure prevents damage to edges of sensitive and soft nuts (Cu) with scale for presetting the opening width apart from the workpiece no unintentional shift of the gripping jaws and no slipping of the joint parallel jaws allow infinitely variable gripping of all widths to the specified maximum size the action of the jaws allows quick tightening and release of bolted connections using the ratchet principle lever transmission greater than 10 – 1 for strong gripping power Chrome vanadium electric steel, forged, oil-hardened

Scale for setting the opening width, apart from the workpiece


4003773- mm

Pliers Handles

Inch mm

Adjustment positions

B1mm

B2mm

B3mm g

86 07 250 065067 250 nickel plated


1 3/4 46 17 8.0 8 14 615

88KNIPEX Alligator® Water Pump Pliers


88 06 250

88 07 250

box-joint design: high stability because of double guide self-locking on pipes and nuts: no slipping on the workpiece and low hand force required guard prevents operators' fingers being pinched favourable lever action: opti-mum transmission of force gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and stable gripping Chrome vanadium electric steel, forged, oil-hardened

Length 250 mmmore output and comfort compared to conventional water pump pliers of the same length: 9-notch adjustment positioning for 30 % more gripping capacity; good access to the workpiece due to slim size in the head and joint area


Pliers Handles

Ø Inch Ø mm mm


88 06 250 039303 250 chrome plated


2 50 46 9 374

88 07 250 019343 250

chrome plated


2 50 46 9 420

88 07 300 022350 300 2 3/4 70 60 9 661

163

INSULATED TOOLS

8726 KNIPEX Cobra® VDE

Hightech Water Pump Pliers, insulated


87 26 250

The adjustment procedure to adapt to the workpiece is easy and reliable with the KNIPEX Cobra® VDE: place the upper gripping jaw of the opened pliers on the workpiece, push pliers handle to close, done!

adjustment by shifting one jaw directly on to the workpiece: fast, reliable and comfortable handling opening at the touch of a button off the workpiece fine adjustment to fit very different workpiece sizes with a comfortable handle position good access to the workpiece due to slim size in the head and joint area self-locking on pipes and nuts: no slipping on the workpiece and low hand force required gripping surfaces with special hardened teeth, teeth hardness approx. 61 HRC: low wear and reliable gripping

Quick setting without using a push-button

Just push the pliers handle to adjust!


Pliers Handles

Ø Inch Ø mm mm


87 26 250 071495 250 chrome plated


2 50 46 24 340

box-joint design: high stability because of double guide guard prevents operators' fingers being pinched Chrome vanadium electric steel, forged, oil-hardened

164

INSULATED TOOLS

92Precision Tweezers IEC 60900 DIN EN 60900

92 27 61

92 27 62

92 37 64

45°

92 67 63

tested according IEC 60900 : 2004with dipped insulationnickel plated Spring steel, high-strength

92 27 61for ultra fine mounting work; extra fine tips; straight pattern; gripping surfaces matt finished for optimum grip

92 27 62straight pattern; gripping surfaces with fine transverse serration

92 37 64angled tips; gripping surfaces with fine transverse serration

92 67 63straight pattern; serrated gripping surfaces


Finish

g



92 37 64 054856 150 45° with dipped insulation 34


950 Cable Shears

IEC 60900 DIN EN 60900

95 06 230

for cutting copper and aluminium cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades no crushing, slight deformation of the cable only guard prevents operators‘ fingers being pinchedadjustable bolted joint Shears body: surgical steel, stainless, vacuum-hardened Handles: plastic, impact-proof

95 06 230for copper single conductors up to 16 mm², multiple stranded wires up to 50 mm², fine stranded up to 70 mm² and aluminium conductors multiple stranded wires up to 70 mm²; easy cutting with one-hand operation due to high transmission ratio; stainless – special grade – steel, oil-hardened and tempered


4003773- mm

Head Handles

Ø mm mm²

AWG

g

95 06 230 006305 230 polished plastic insulated, VDE-tested 16 50 1/0 274

165

INSULATED TOOLS

951 Cable Shears

IEC 60900 DIN EN 60900

95 16 165

95 26 165

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades clean and smooth cut without crushing and deformation easy cutting with one-hand operation guard prevents operators‘ fingers being pinched adjustable bolted joint, self-retaining screw High-grade special tool steel, forged, oil-hardened

Style 2internal opening spring, protected and captive

Cut performed with a Diagonal Cutter: high effort required, inaccurate cut, considerable deforming and crushing of the cable

Cut effected with a Cable Shear: easy, clean cut without any deformation of the cable


4003773- mm

Tool Handles

Ø mm mm²

AWG

g

95 16 165 039648 165 chrome plated


15 50 1/0 262

95 26 165 069980 165 chrome plated


15 50 1/0 275

166

INSULATED TOOLS


IEC 60900 DIN EN 60900

95 16 200

95 17 200

for cutting copper and aluminium cables not suitable for steel wire and hard drawn copper conductors precision ground, hardened blades clean and smooth cut without crushing and deformation easy cutting with one-hand operation initial and final cut (upper and lower blade) allows cables of up to 20 mm dia. to be cut low hand force required due to favourable lever ratio and new blade geometry guard prevents operators‘ fingers being pinchedadjustable bolted joint, self-retaining screw High-grade special tool steel, forged, oil-hardened

Initial cut: using the front cutting edge to cut the insulating sheath on larger cable diameters leaves an ergonomic handle opening width.

Final cut: after cutting the sheath in the front profile the cut is finished through the metal part of the cable in the rear profile. Initial cut in the front profile, final cut in the rear profile - to keep it as easy as possible.


4003773- mm

Ttool Handles

Ø mm mm²

AWG

g

95 16 200 026761 200 chrome plated

insulated with multi-component grips, VDE-tested 20 70 2/0 340

95 17 200 026952 200 chrome plated

with dipped insulation, VDE-tested 20 70 2/0 360

167

INSULATED TOOLS

951 Cable Shears

IEC 60900 DIN EN 60900

95 17 500

for cutting copper and aluminium single conductors as well as multiple stranded cablesnot suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation less effort required due to favourable lever ratio and optimised cutting-edge geometry short design, length only 500 mm low weight guard prevents operators‘ fingers being pinched adjustable bolted joint Cutter head: Vanadium electric steel, forged, oil-hardened Handles: aluminium tube, high-strength

Large cutting capacity: max. 27 mm dia. / 150 mm²


4003773- mm

Head Handles

Ø mm mm²

AWG

g


952 Cable Shears

IEC 60900 DIN EN 60900

95 27 600

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation favourable transmission ratio due to double lever favourable lever ratio due to toggle lever guard prevents operators‘ fingers being pinchedadjustable bolted joint bolted cutter head, replaceableBlade head: high-grade chrome vanadium electric steel, forged, oil-hardened Handles: steel tube


4003773- mm

Head Handles

Ø mm mm²

AWG

g



168

INSULATED TOOLS

953 Cable Cutters ratchet action

IEC 60900 DIN EN 60900

95 36 280

for cutting copper and aluminium single conductors as well as multiple stranded cables not suitable for steel wire and wire ropes precision ground, hardened blades clean and smooth cut without crushing and deformation one-hand operation using ratchet principle little hand force required due to very high transmission ratio two-stage ratchet drive for easy cutting simple handling as a result of low weight and compact design – can be used even in confined areas guard prevents operators‘ fingers being pinched High-grade special tool steel, forged, oil-hardened

95 36 280suitable for aluminium sector cable up to 4 x 150 mm²

Ratchet principle and two-stage ratchet drive for easier cutting


4003773- mm

Tool Handles

Ø mm mm²

MCM

g

95 36 250 026884 250 black lacqueredinsulated with multi-component grips, VDE-tested

32 240 500 652

95 36 280 026891 280 black lacquered insulated with multi-component grips, VDE-tested

52 380 750 835



957 Wire Rope and ACSR-Cable Cutter

IEC 60900 DIN EN 60900

95 77 600

for wire ropes and steel rods, copper and aluminium cables suitable for cutting overhead line cables with strain relief wire (ACSR cables) angular cutting blades allow cutting of single rope wire optimum transmission ratio for high cutting performance bolted cutter head, replaceable high-strength aluminium handles low weight


4003773- mm

Head Handles

mm² Ø mm Ø mm

AWG

g

95 77 600 025313 600 polished with dipped insulation 150 14.0 9.0 5/0 2359


Cutter head: high-grade special tool steel, oil-hardened Handles: aluminium, high-strength

169

INSULATED TOOLS


(ferrules) IEC 60900 DIN EN 60900

97 68 145 A

for crimping end sleeves (ferrules) according DIN 46228 parts 1 + 4 in an area of application from 0.25 up to 2.5 mm² crimping in marked trapezoidal dies for reliable connections between the sleeve and the conductor Vanadium electric steel; forged, oil-hardened


Head Handles Capacitymm²

AWG Number of crimping positions g

97 68 145 A 071754 145 polishedinsulated with multi-component grips, VDE-tested

0.25 - 2.5 23 - 13 6 175

170

INSULATED TOOLS

980 Open End Wrenches

IEC 60900 DIN EN 60900

98 00 14

jaw 15° angled basic tool chrome plated Chrome vanadium steel, forged, oil-hardened


Width across flats Smm

Width across flats SInch

Length l max. mm

Head width b max. mm

Head thickness a max. mm g

98 00 07 019824

7.0 105.0 20.0 4.0 15

98 00 08 019831 8.0 105.0 22.0 4.0 31

98 00 09 019848 9.0 105.0 24.0 4.0 29

98 00 10 019893 10.0 105.0 27.0 5.0 40

98 00 11 019909 11.0 120.0 30.0 5.5 45

98 00 12 019923 12.0 125.0 32.0 5.5 70

98 00 13 019930 13.0 130.0 34.0 6.5 68

98 00 14 019947 14.0 135.0 35.0 6.5 86

98 00 15 019954 15.0 145.0 37.0 7.0 80

98 00 16 019961 16.0 155.0 38.0 7.0 112

98 00 17 019978 17.0 155.0 42.0 8.0 119

98 00 18 019985 18.0 160.0 44.0 8.0 149

98 00 19 019992 19.0 165.0 47.0 9.0 154

98 00 22 020004 22.0 190.0 52.0 9.0 216

98 00 24 020011 24.0 210.0 56.0 9.0 262

98 00 27 020028 27.0 215.0 63.0 9.0 307

98 00 1/4“ 019886 1/4 108.0 20.0 4.0 32

98 00 5/16“ 020073 5/16 108.0 22.0 4.0 36

98 00 3/8“ 020042 3/8 108.0 27.0 5.0 37

98 00 7/16“ 020097 7/16 120.7 30.0 5.5 53

98 00 1/2“ 019879 1/2 139.7 34.0 6.5 60

98 00 9/16“ 020110 9/16 152.4 35.0 6.5 102

98 00 5/8“ 020080 5/8 165.1 38.0 7.0 124

98 00 3/4“ 020035 3/4 190.5 47.0 9.0 164

98 00 1 1/16“ 019855 1 1/16 215.0 63.0 9.0 400

171

INSULATED TOOLS

980 Box Wrenches

IEC 60900 DIN EN 60900

98 01 14

cranked basic tool chrome plated Chrome vanadium steel, forged, oil-hardened



Length l max. mm

Head width b max. mm

Head thickness a max. mm

Depth of crank h max. mm g

98 01 07 020134

7.0 150.0 12.0 7.0 18.0 55

98 01 08 020141 8.0 155.0 14.0 7.0 19.0 68

98 01 09 020158 9.0 165.0 15.5 8.0 19.0 78

98 01 10 020196 10.0 160.0 17.0 9.0 20.0 75

98 01 11 020202 11.0 165.0 18.5 10.0 21.0 93

98 01 12 020226 12.0 185.0 18.5 10.0 23.0 118

98 01 13 020233 13.0 185.0 21.5 11.0 23.0 125

98 01 14 020240 14.0 195.0 23.0 12.0 24.0 147

98 01 15 020257 15.0 200.0 24.0 12.0 24.0 143

98 01 16 020264 16.0 200.0 26.0 12.0 26.0 172

98 01 17 020271 17.0 205.0 27.0 13.0 26.0 184

98 01 18 020288 18.0 210.0 29.0 13.0 28.0 210

98 01 19 020295 19.0 225.0 30.0 14.0 28.0 245

98 01 22 020301 22.0 225.0 35.0 15.0 30.0 268

98 01 24 020318 24.0 265.0 38.0 16.0 30.0 961

172

INSULATED TOOLS

980 Nut Drivers with screwdriver handle

IEC 60900 DIN EN 60900

98 03 10

ergonomically optimised dual component handle for fatigue reduced work and optimum transmission of force handle design prevents rolling Chrome vanadium molybdenum steel


Tip Handle Width across flats Smm

Blade lengthmm

Handle length

mm

Head dia.mm g

98 03 04 071679 230

burnished

insulating multi-component handle, VDE-tested

4.0 125.0 107 9.0 70

98 03 05 071686 230 5.0 125.0 107 10.0 70

98 03 055 026082 232 5.5 125.0 107 11.0 87

98 03 06 026099 232 6.0 125.0 107 12.0 88

98 03 07 026105 237 7.0 125.0 112 14.0 123

98 03 08 024095 237 8.0 125.0 112 15.0 125

98 03 09 026112 237 9.0 125.0 112 16.0 129

98 03 10 026129 237 10.0 125.0 112 17.0 118

98 03 11 026136 237 11.0 125.0 112 19.0 148

98 03 12 026143 237 12.0 125.0 112 20.0 150

98 03 13 026150 237 13.0 125.0 112 21.0 152

Sd

Sd

980 Nut Drivers with T-handle

IEC 60900 DIN EN 60900

98 04 13

98 05 13

Special tool steel, oil-hardened



Handle length max.mm

Head dia.mm g

98 04 08 071341 200

8.0 90 15.0 344

98 04 10 026167 200 10.0 155 19.5 324

98 04 13 026198 200 13.0 155 23.5 344

98 04 17 026211 200 17.0 155 28.5 426

98 04 19 020424 200 19.0 155 31.0 525

98 04 22 026228 200 22.0 155 34.5 560

98 05 13 026273 300

13.0 155 23.5 409

98 05 17 026297 300 17.0 155 28.5 544

98 05 19 026303 300 19.0 155 31.0 674

173

INSULATED TOOLS

9807 Adjustable Wrench

98 07 250

22°

parallel smooth gripping jaws continuously variable gripping width with scaling for presetting the width apart from the workpiece Chrome Vanadium steel


Tool Handle

mm Inch

Jaw widthmm

Head widthmm

Widthmm

Depthmm g

98 07 250 071518 260 22° chrome plated

with dipped insulation

30 1 1/8 8.0 16.0 73.0 20.0 500

981 Screwdrivers for hexagon

socket screws IEC 60900 DIN EN 60900

98 13 30



Tip Handle Width across flats Smm

Blade lengthmm

Length of non-insulated blade

mm

Handle length

mm g

98 13 20 071693 175

burnished


2.0 75.0 15.0 102 40

98 13 25 026334 177 2.5 75.0 15.0 102 32

98 13 30 026341 182 3.0 75.0 15.0 107 49

98 13 40 026358 182 4.0 75.0 15.0 107 55

98 13 50 026365 187 5.0 75.0 15.0 112 82

98 13 60 026372 212 6.0 100.0 15.0 112 98

S

174

INSULATED TOOLS

981 Screwdrivers for hexagon socket

screws with T-handle

IEC 60900 DIN EN 60900

98 14 08

98 15 08

Special tool steel, oil-hardened



Length of non-insulated blade ± 2mm

T-handle lengthmm g

98 14 05 020431 120

5.0 9.0 90.0 220

98 14 06 020448 120 6.0 10.0 90.0 208

98 14 08 020455 120 8.0 11.0 90.0 286

98 15 05 020479 250

5.0 9.0 90.0 363

98 15 06 020486 250 6.0 10.0 90.0 452

98 15 08 020493 250 8.0 11.0 90.0 359

S

982 Screwdrivers for slotted screws

IEC 60900 DIN EN 60900

98 20 55


98 21 45especially for meter assembly with blade length of 180 mm


Tip Handle Blade widthmm

Blade thickness mm

Length of blademm

Length of non-insulated blade

mm

Handle length

mm g

98 20 10 026396 320

burnished


10.0 1.6 200 15 120 184

98 20 25 062325 177 2.5 0.4 75 15 102 32

98 20 30 062332 202 3.0 0.5 100 15 102 35

98 20 35 024217 202 3.5 0.6 100 15 102 35

98 20 40 026402 202 4.0 0.8 100 15 102 38

98 20 55 024224 232 5.5 1.0 125 15 107 69

98 20 65 026419 262 6.5 1.2 150 15 112 105

98 20 80 024231 295 8.0 1.2 175 15 120 152

98 21 45 026426 287

burnished

insulating multi-compo-nent handle, VDE-tested

4.5 0.8 180 15 107 66

175

INSULATED TOOLS

982 Screwdrivers for cross-recessed

screws Phillips®

IEC 60900 DIN EN 60900

98 24 03



Tip Handle Size Blade lengthmm

Length of non-insulated blade mm

Handle length

mm g

98 24 00 026433 162

burnishedinsulating multi-component handle, VDE-tested

PH 0 60 15 102 32

98 24 01 026440 187 PH 1 80 15 107 58

98 24 02 026457 212 PH 2 100 18 112 94

98 24 03 026464 270 PH 3 150 18 120 165

98 24 04 026471 320 PH 4 200 18 120 244

982 Screwdrivers for cross-recessed

screws Pozidriv®

IEC 60900 DIN EN 60900

98 25 03





Handle length

mm g

98 25 00 062370 162


PZ 0 60 15 102 40

98 25 01 031260 187 PZ 1 80 15 107 58

98 25 02 031277 212 PZ 2 100 18 112 94

98 25 03 031284 270 PZ 3 150 18 120 165

98 25 04 062387 320 PZ 4 200 18 120 85

982 Screwdrivers for Torx® screws

IEC 60900 DIN EN 60900

98 26 30





Handle length

mm g

98 26 10 071709 160


TX 10 60 15 102 25

98 26 15 071716 185 TX 15 80 15 107 25

98 26 20 071723 185 TX 20 80 15 107 25

98 26 25 071730 185 TX 25 80 15 107 25

98 26 30 071747 210 TX 30 100 18 112 25

176

INSULATED TOOLS

9840 T-handle with driving square 3/8“ or 1/2“

IEC 60900 DIN EN 60900

98 40

for use with sockets quick, easy and reliable locking of attached sockets basic tool chrome plated High-grade special tool steel, forged, oil-hardened


Handle length

mm

Square drive Inch g

98 30 026488 200 165 3/8 447

98 40 026501 200 165 1/2 631

98Reversible Ratchets with driving square 3/8“ or 1/2“

IEC 60900 DIN EN 60900

98 31

for use with sockets reversible for clockwise and anti-clockwise directions extremely smooth action quick, easy and reliable locking of attached sockets Chrome vanadium steel, forged


Square driveInch g

98 31 026495 190 3/8 324

98 41 026518 265 1/2 625

98Extension Bars with internal and driving square 3/8“ or 1/2“

IEC 60900 DIN EN 60900

98 35 125

98 45 250

for use with sockets with internal and external square quick, easy and reliable locking of attached sockets Chrome vanadium steel, forged


Square drive Inch g

98 35 125 020530 125

3/8 149

98 35 250 020547 250 3/8 294

98 45 125 020813 125

1/2 258

98 45 250 020820 250 1/2 490

177

INSULATED TOOLS

98Hexagon Sockets for hexagonal screws for internal square 3/8“ or 1/2“

IEC 60900 DIN EN 60900

98 37 17

for metric and imperial hexagonal head screws basic tool chrome plated Chrome Vanadium steel



Width across flats SInch

dia. of effective tool side d max.mm

Square driveInch g

98 37 10 020578

10.0 18.7 3/8 32

98 37 11 020585 11.0 20.0 3/8 32

98 37 12 020608 12.0 21.2 3/8 33

98 37 13 020615 13.0 22.5 3/8 33

98 37 14 020622 14.0 23.7 3/8 39

98 37 17 020639 17.0 27.5 3/8 61

98 37 19 020646 19.0 30.0 3/8 73

98 37 5/16“ 020684 5/16 16.2 3/8 30

98 37 3/8“ 020677 3/8 18.7 3/8 31

98 37 7/16“ 020707 7/16 20.0 3/8 31

98 37 1/2“ 020554 1/2 22.5 3/8 33

98 37 9/16“ 020721 9/16 23.7 3/8 39

98 37 5/8“ 020691 5/8 26.2 3/8 51

98 37 3/4“ 020660 3/4 30.0 3/8 71

98 37 1/4“ 020561 1/4 14.7 3/8 30

98 47 10 020882

10.0 19.5 1/2 63

98 47 11 020899 11.0 20.7 1/2 61

98 47 12 020912 12.0 23.0 1/2 64

98 47 13 020929 13.0 23.2 1/2 64

98 47 14 020943 14.0 24.5 1/2 67

98 47 16 027287 16.0 26.9 1/2 69

98 47 17 020967 17.0 28.2 1/2 75

98 47 18 027294 18.0 29.0 1/2 81

98 47 19 020974 19.0 30.7 1/2 99

98 47 22 020981 22.0 34.5 1/2 125

98 47 24 020998 24.0 37.0 1/2 151

98 47 27 021001 27.0 41.0 1/2 183

98 47 1/2“ 020875 1/2 23.2 1/2 67

98 47 9/16“ 021094 9/16 24.5 1/2 64

98 47 5/8“ 021063 5/8 26.9 1/2 72

98 47 11/16“ 020905 11/16 28.2 1/2 88

98 47 3/4“ 021018 3/4 30.7 1/2 97

98 47 7/8“ 021087 7/8 34.5 1/2 124

98 47 1“ 020868 1 41.0 1/2 167

Sd

178

INSULATED TOOLS

179

INSULATED TOOLS

984 Reversible Ratchet with driving square 1/2“

ISO 3315 IEC 60900 DIN EN 60900

98 42

reversible for clockwise and anti-clockwise directions very reliable retention of the actuating tools ensured by mechanically locked retaining system Chrome Vanadium steel


Square driveInch g

98 42 026525 265 1/2 599

98Torque Wrench with driving square, reversible

DIN EN ISO 6789 IEC 60900 DIN EN 60900

98 43 50

reversible for tightening of lefthanded threads lockable torque adjustment very reliable retention of the actuating tools ensured by mechanically locked retaining system transparent insulated scale range calibration certificate included Chrome Vanadium steel


Range of Application Square drive Inch g

98 33 25 072676 290

5 - 25 Nm 3/8 1230

98 33 50 071761 385 5 - 50 Nm 3/8 1230

98 43 50 071778 385 5 - 50 Nm 1/2 1230

98Hexagon Sockets for hexagon socket screws for internal square 3/8“ or 1/2“

DIN 7422 IEC 60900 DIN EN 60900

98 39 06

for metric internal hexagonal head screws basic tool chrome plated Special tool steel



Length of non-insulated blade ± 2mm

Square driveInch g

98 39 05 020776 75

5.0 9 3/8 59

98 39 06 020783 75 6.0 10 3/8 58

98 49 05 021155 75

5.0 9 1/2 68

98 49 06 021162 75 6.0 10 1/2 72

98 49 08 021179 75 8.0 11 1/2 87

Transparent insulated scale range

S

180

INSULATED TOOLS

985 Cable Knives

IEC 60900 DIN EN 60900

98 52

98 54

ergonomically improved handle shape with comfortable slip guard particularly confident grip thanks to slip-proof soft components thumb recess and "finger hook" at the end of the handle ensure a good transmission of force when the blade is pulled solid, fixed straight blade transparent protective cap Blade: special tool steel, oil-hardened

98 54back of the blade plastic coated to avoid short circuits


Handle Blade lengthmm g

98 52 035565 180 insulating multi-component handle, VDE-tested 50 67

98 54 026563 180 insulating multi-component handle, VDE-tested 50 68

985 Dismantling Knives

IEC 60900 DIN EN 60900

98 53 03

98 53 13

98 55

ergonomically improved handle shape with comfortable slip guard particularly confident grip thanks to slip-proof soft components thumb recess and "finger hook" at the end of the handle ensure a good transmission of force when the blade is pulled transparent protective cap

98 53 03solid, fixed hook blade; suitable for round cables; Blade: special tool steel, oil-hardened

98 53 13narrow, fixed hook blade, sickle shaped; suitable for sector cables; Blade: special tool steel, oil-hardened

98 55solid, fixed hook blade, sickle shaped; with guide shoe at the blade point; no damage of the conductor insulation; Blade: surgical steel, stainless, vacuum-hardened


Handle Blade lengthmm

Radiusmm g

98 53 03 026549 155 insulating multi-component handle, VDE-tested 28 7 64

98 53 13 026556 180 insulating multi-component handle, VDE-tested 50 40 64

98 55 022558 155 insulating multi-component handle, VDE-tested 38 23.5 68

181

INSULATED TOOLS

985 Cable Knife with replaceable blade

IEC 60900 DIN EN 60900

98 56

98 62 01

straight blade with special sharpening; replaceable with hinged blade guard, integrated in the handle, captive back of the blade plastic coated to avoid short circuits ergonomically shaped insulating handle Blade: surgical steel, stainless, vacuum hardened


Blade lengthmm g

98 56 026570 185 50 64

98 56 09 030829 Spare blade for 98 56

9860 Voltage tester with load application

DUSPOL® compact

DIN VDE 0682-401 IEC 61243-3 EN 61243-3

98 60 04

overvoltage category: CAT IV 500 V, III 690 V LED display shows direct and alternating current levels 12, 24, 50, 120, 230, 400 and 750 V polarity test with direct voltage intentional RCCB tripping protection class: IP 64 (dust-proof and splash-proof)


98 60 04 051961 1400 188

986 Flat Nose Pliers of plastic, insulating

IEC 60900 DIN EN 60900 ASTM F1505the insulating construction reduces risk of short circuits for meter installation and meter blocking Plastic material, fibreglass reinforced


98 62 01 073956 180 130

986 Snipe Nose Pliers of plastic, insulating

IEC 60900 DIN EN 60900 ASTM F1505the insulating construction reduces risk of short circuitsPlastic material, fibreglass reinforced


98 62 02 073963 220 140

98 62 02

182

INSULATED TOOLS

986 Insulating Clamp solid plastic, insulating

DIN VDE 0680-1

98 64 02

for holding insulating mats in place with integrated spring the insulating construction reduces the risk of short circuits Solid plastic, fibreglass-reinforced


Clamping capacity

mm g

98 64 02 021193 150 15 61

986 Plastic Slip-On Caps conical

DIN VDE 0680-1

98 65 01

to cover bare live cable ends (max. 10 mm dia.) Plastic


Conductor key

g

98 65 01 021209 80 1 7

98 65 02 021216 80 2 8

98 65 03 021223 80 3 8

986 Self-Clamping Slip-On Caps

DIN VDE 0680-1

98 65 30

to cover bare live cable ends Plastic


Inside dia.mm g

98 65 10 021230 80 10 9

98 65 20 021247 100 20 39

98 65 30 021261 110 30 52

986 Electricians‘ Gloves

IEC 60903 DIN EN 60903

98 65 40

for added protection when working live or close to live parts classification: 0


Size

g

98 65 40 021285 9 290

98 65 41 021292 10 288

183

INSULATED TOOLS

986 Insulating Mats from rubber

DIN VDE 0680-1

98 67 05

for added protection when working live or close to live parts


Dimensionsmm

Thicknessmm g

98 67 05 026600

500 x 500 1.0 301

98 67 10 026617 1000 x 1000 1.0 1200

9890 PUK® Junior Hacksaw

IEC 60900 DIN EN 60900

98 90

saw blade for metal and wood with 25 teeth per inch, exchangeable


Saw blade lengthmm g

98 90 028321 240 150 174

989 Compact Tool Case 17 parts

with insulated tools for works on electrical installations

IEC 60900 DIN EN 60900

98 99 11

shock-resistant plastic case containing a range of insulated KNIPEX tools for works on electrical installations foam inserts with recesses for the tools fixable partition wall dimensions, exterior (W x H x D): 360 x 110 x 310 mm


Units

g

98 99 11

026624

Compact Tool Case 17 parts 3675

03 07 200 Combination Pliers 1 70 07 160 Diagonal Cutter 1 98 20 35

Screwdrivers for slotted screws

1

98 20 40 1

98 20 55 1

98 24 00Screwdrivers for cross-recessed screws

1

98 42 Reversible Ratchet 1 98 45 125

Extension Bars1

98 45 250 1

98 47 10

Hexagon Sockets for hexagonal screws

1

98 47 11 1

98 47 12 1

98 47 13 1

98 47 14 1

98 47 17 1

98 47 19 1

98 52 Cable Knife 1

184

INSULATED TOOLS

989 Standard Tool Case 26 parts


IEC 60900 DIN EN 60900

98 99 12

containing a range of insulated KNIPEX tools for works on electrical installations shock-resistant plastic case foam inserts with recesses for the tools fixable partition wall dimensions, exterior (W x H x D): 440 x 105 x 385 mm


Units

g

98 99 12

026631

Standard Tool Case 26 parts 4230

03 07 200 Combination Pliers 1 70 07 160 Diagonal Cutter 1 98 00 10

Open End Wrench

1

98 00 11 1

98 00 12 1

98 00 13 1

98 00 14 1

98 00 17 1

98 00 19 1

98 53 03 Dismantling Knife for round cable 1 98 20 25


1

98 20 35 1

98 20 40 1

98 20 55 1

98 24 00

Screwdrivers for cross-recessed screws, Philips®

1

98 24 01 1

98 24 02 1

98 40 T-handle 1 98 47 10

Hexagon Socket for hexagonal screws

1

98 47 11 1

98 47 12 1

98 47 13 1

98 47 14 1

98 47 17 1

98 47 19 1

98 52 Cable Knife 1

185

INSULATED TOOLS

989 Tool Roll 15 parts


IEC 60900 DIN EN 60900IEC 60900 DIN EN 60900

98 99 13

tool roll made of hard-wearing polyester fabric with practical, adjustable quick release fastener containing a range of insulated KNIPEX tools for works on electrical installations


Units

g

98 99 13

026648

Tool Roll 15 parts 2455

03 07 200 Combination Pliers 1 11 07 160 Insulation Stripper 1 26 17 200 Snipe Nose Side Cutting Pliers 1 70 07 160 Diagonal Cutter 1 95 17 200 Cable Shear 1 98 00 10

Open End Wrench

1

98 00 13 1

98 00 14 1

98 00 17 1

98 00 19 1

98 20 25

Screwdriver for slotted screws

1

98 20 40 1

98 20 55 1

95 20 65 1

98 52 Cable Knife 1

186

INSULATED TOOLS

989 Universal Tool Case 48 parts


IEC 60900 DIN EN 60900

98 99 14

00 21 40 T

98 99 14hard-wearing case made of ABS material, red; containing a range of KNIPEX tools for works on electrical installations, tested according to DIN EN/IEC 60900, as well as insulating mats, clamps and gloves for added protectionsturdy aluminium frame with D-shape rings for belt and fix, sturdy centre board with multi-purpose push-in facilities by elastic loops and 12 small pocketscomfortable handle and mounting device for a "Trolley" embedded in the bottom (available ordering ref. 00 21 40 T)metal hinges30 kg maximum loadcan be opened on one or both sides; bottom tray and cover can be opened independentlystands stable in any opening position due to lid-holders and hinge mechanisms on both sides, that register in a position of 45° and 90°3-digit lock and two flip-locks for fixation of the coverremovable document compartment and removable tool board, with 13 push-in compartments on one sidetwo flip-locks to fix the bottombase tray, height 58 mm, can be subdivided by flexible inserts; cover plate with six large push-in compartments, can be fixed by popperdimensions, external ( W x H x D): 490 x 255 x 410 mm dimensions, internal (W x H x D) : 445 x (105 + 105) x 350 mm

00 21 40 Ttelescopic handle for rolling transport of tool caseapplicable for cases: 00 21 40 LE Tool Case "BIG Twin", 98 99 14 Universal Tool Caseheight adjustable handle with catchintegrated mechanism for fixation to the case, for rapid assembly and removalwith two smooth running rollsdimensions: 60 x 245 x 400 (1.000) mm (extended)

187


Quantity

g

98 99 14 026655 Universal Tool Case 48 parts 16250

03 07 200 Combination Pliers 200 mm 1 11 17 160 Insulation Stripper 160 mm 1

70 07 160 Diagonal Cutter 160 mm 1 88 07 250 KNIPEX Alligator® 250 mm 1

95 17 200 Cable Shears 200 mm 1 98 00 10

Open End Wrench

SW 10 mm 1

98 00 13 SW 13 mm 1

98 00 14 SW 14 mm 1

98 00 17 SW 17 mm 1

98 00 19 SW 19 mm 1

98 00 22 SW 22 mm 1

98 01 10

Box Wrench

SW 10 mm 1

98 01 13 SW 13 mm 1

98 01 14 SW 14 mm 1

98 01 17 SW 17 mm 1

98 01 19 SW 19 mm 1

98 01 22 SW 22 mm 1

98 67 05 Insulating Mat 500 x 500 1.6 mm 3

98 20 25

Screwdriver for slotted screws

2.5 mm 1

98 20 40 4.0 mm 1

98 20 55 5.5 mm 1

98 20 65 6.5 mm 1

98 24 01Screwdriver for cross-recessed screws

PH 01 1

98 24 02 PH 02 1

98 40 T-Handle 165 mm 1

98 42 Reversible Ratchet 265 mm 1

98 45 125Extension Bar

125 mm 1

98 45 250 250 mm 1

98 47 10

Hexagon Socket for hexagonal screws

SW 10 mm 1

98 47 11 SW 11 mm 1

98 47 12 SW 12 mm 1

98 47 13 SW 13 mm 1

98 47 14 SW 14 mm 1

98 47 17 SW 17 mm 1

98 47 19 SW 19 mm 1

98 47 22 SW 22 mm 1

98 47 24 SW 24 mm 1

98 52 Cable Knife 180 mm 1

98 53 03 Dismantling Knife for round cable 155 mm 1

98 64 02 Insulating Clamp 150 mm 6

98 65 40 Electricians‘ Gloves 9 1

98 99 14 LE 060703 Universal Tool Case, empty 7960

00 21 40 T 062981 Trolley 1200

INSULATED TOOLS

Model 99 Concretors‘

Nippers,

see starting from Page 64

188

CONTROL CABINET KEYS

0011 Control Cabinet Keys

for all standard cabinets and shut-off systems

00 11 03

for control cabinets and shut-off systems in the supply of gas, water and electricity for technical installations in buildings, e.g. air conditioning and ventilation systems, shut-off valves, mains switchboards, etc. with bit insert: slot 1.0 x 7 mm and cross recess PH 2 with adapter for 1/4" bits on chained to key additional bit adapter for 1/4" bits inside one profileZinc die-casted

00 11 02short version, total length 44 mm


00 11 02 048947 44 5 / 6 / 8 9 3 - 5 65

00 11 03 041658 76 5 / 6 / 8 9 3 - 5 88

0011 Profi-Key

for all standard shut-off systems

00 11 04

key for heating, air conditio-ning, sanitary and building technology, e.g. for door and window handles or for radiator-bleeding with bit insert: slot 1.0 x 7 mm and cross recess PH 2 with adapter for 1/4" bits chained to keyadditional bit adapter for 1/4" bits inside one profile total length: 90 mm Zinc die-casted


00 11 04 048954 90 5 / 7 / 8 9 - 10 6 / 7 / 8 / 9 86

0011 Universal Key


00 11 06

for locking systems in electrical engineering, the supply of gas and water, air conditioning and ventilation systems, industry, technical installations in buildings, etc. 9 different die-cast zinc key-profiles in 1 tool with detachable chain and snap hook total length: 90 mm Zinc die-casted

Article No. EAN4003773- mm mm mm mm mm g

00 11 06 071334 90 5 / 6 / 7 - 8 / 9 - 10 7 / 8-9 / 10 - 11 3 - 5 6 220

189


0011 Pen-Style Control Cabinet Key


00 11 07

easy to carry pen-style control cabinet key with fastening clip four different key profiles can be utilized by swivelling the key holder for control cabinets and shut-off systems in the supply of gas, water and electricity for technical installations in buildings, e.g. air conditioning and ventilation systems, shut-off valves, mains switchboards, etc. universal 1/4" bit adapter for standard bits (permanent magnet for retaining) additional bit adapter for 1/4" bits inside one key profile with inserted bit: cross recess PH 2 and possibility of safekeeping a second bit Tool body: plastic, fibreglass-reinforced Key profiles: zinc die-casted


00 11 07 063018 145 5 / 6 / 8 9 3 - 5 152

0011 Pen-Style Profi-Key

for all standard shut-off systems

00 11 08

easy to carry pen-style control cabinet key with fastening clip three different key profiles can be utilized by swivelling the key holder multi-purpose wrench for access on construction sites with profiles for the areas of heating, air conditioning, plumbing and building technology, e.g. for door and window handles or for radiator-bleeding universal 1/4" bit adapter for standard bits (permanent magnet for retaining) additional bit adapter for 1/4" bits inside one key profile with inserted bit: cross recess PH 2 and possibility of safekeeping a second bit Tool body: plastic, fibreglass-reinforced Key profiles: zinc die-casted


00 11 08 063025 145 5 / 8 9 6 / 7 / 8 / 9 142

190


0011 Pen-Style Control Cabinet Key

with voltage detector


00 11 17

easy to carry pen-style control cabinet key with fastening clip contactless detection of alternating current with optical indication; range of voltage 50 - 600 V; frequency range 50 - 60 Hz on / off button indicated by means of a bright LED: start-up self test, battery control and live conductor close-by detection battery case with bayonet catch four different key profiles can be utilized by swivelling the key holder for control cabinets and shut-off systems in the supply of gas, water and electricity for technical installations in buildings, e.g. air conditioning and ventilation systems, shut-off valves, mains switchboards, etc. universal 1/4" bit adapter for standard bits (permanent magnet for retaining) additional bit adapter for 1/4" bits inside one key profile with inseted bit: cross recess PH 2 Tool body: plastic, fibreglass-reinforced Key profiles: zinc die-casted


00 11 17 068396 155 6 / 8 9 3 - 5 136

191

TOOL KITS

0019 Counter Displays

00 19 12 V01

00 19 12 V02

00 19 12 V03

■ made from high-quality paperboard printed with high gloss finish


Contents Quantity Widthmm

Heightmm

Depthmm g

00 19 12 V01 070368 86 03 150 Mini Pliers Wrench 8 170 288 345 1590

00 19 12 V02 070375 86 05 150 Mini Pliers Wrench 8 170 290 345 1775

00 19 12 V03 070740 87 01 125 KNIPEX Cobra® 12 290 280 160 1245

0019 Counter Displays 10 parts

00 19 19 V02

■ all-round colouring with neutral header ■ small size, minimum space required at the point of sales ■ dimensions, assembled (W x H x D): 225 x 435 x 225 mm ■ dimensions, packed (W x H x D): 260 x 350 x 260 mm ■ other contents (5 + 5 or 10 pieces) possible, minimum quantity

and delivery time on request ■ Material: solid cardboard, printed


Contents

g

00 19 19 V01 073147 10 x 68 01 200 3610

00 19 19 V02 073154 10 x 87 01 250 3560

00 19 19 V03 073161 10 x 88 01 180 2220

00 19 19 V04 073178 10 x 88 01 250 3610

00 19 19 V05 073185 10 x 99 01 280 5420

00 19 19 V06 073192 5 x 68 01 160 / 5 x 68 01 180 2850

00 19 19 V07 073208 5 x 85 01 250 / 5 x 87 41 250 3910

00 19 19 V08 073215 5 x 86 03 180 / 5 x 86 03 250 4370

00 19 19 V09 073222 5 x 87 01 180 / 5 x 87 01 250 2540

00 19 19 V10 073239 5 x 87 01 250 / 5 x 87 01 300 4645

00 19 19 V11 073246 5 x 88 01 250 / 5 x 88 01 300 4570

00 19 19 V12 073253 5 x 99 00 250 / 5 x 99 00 280 4370

00 19 19 V13 073789 10 x 71 01 200 3820

192

TOOL KITS

0019 Cobra® range in sales display

00 19 29

■ attractive sales display for presentation of the Cobra® familiy ■ solid style; can be fixed on tool bar systems, also suitable

as counter display ■ with integrated brochure holder for "Cobra®" leaflets ■ with transparent label holders ■ please do always request leaflets and labels ■ includes three "Cobras®" each 87 01 150/180/250/300/400/560 ■ Material: steel wire, silver powder coated


Contents Quantity Width mm

Height mm

Depth mm g

00 19 29

052340 Sales Display for KNIPEX Cobra® Water Pump Pliers 610 445 250 19600

87 01 150 3

87 01 180 3

87 01 250 3

87 01 300 3

87 01 400 3

87 01 560 3

0019 Tool Roll 11 parts

00 19 41

■ for telecommunications and electrical engineers ■ tool roll made of hard-wearing polyester fabric ■ with practical, adjustable quick release fastener ■ contains eight pliers and three scewdrivers ■ pliers with chrome plated heads and two-colour dual component

handles ■ screwdrivers VDE tested according to DIN EN/IEC 60900 1000V


Contents Quantity

g

00 19 41

024729

Tool Roll 11 parts 1620

03 05 160 Combination Pliers 1 11 15 160 Insulation Stripper 1

25 05 160 Snipe Nose Side Cutting Pliers 1 30 15 160 Long Nose Pliers 1 30 35 160 Long Nose Pliers 1 31 15 160 Gripping Pliers 1 67 05 140 High Leverage End Cutting Nipper 1

70 05 140 Diagonal Cutter 1

98 20 25 Screwdriver for slotted screws 2.5 mm 1 98 20 40 Screwdriver for slotted screws 4.0 mm 1 98 24 01 Screwdriver for cross-recessed screws PH 01 1

193

TOOL KITS

0019 Circlip Pliers Sets 4 parts

00 19 56

00 19 57

■ tool roll made of hard-wearing polyester fabric

■ with practical, adjustable quick release fastener

00 19 56contains four common Circlip Pliers for internal and external circlips

00 19 57contains common Precision Circlip Pliers for highest requirements


Contents Style TipsØ mm

Quantity

g

00 19 56

030973

Circlip Pliers Set 4 parts 670

44 11 J2 Circlip Pliers straight tips 19 - 60 1

44 21 J21 Circlip Pliers angled tips 19 - 60 1 90°

46 11 A2 Circlip Pliers straight tips 19 - 60 1 46 21 A21 Circlip Pliers angled tips 19 - 60 1 90°

00 19 57

050056

Circlip Pliers Set 4 parts 665

48 11 J1 Precision Circlip Pliers straight tips 12 - 25 1 48 11 J2 Precision Circlip Pliers straight tips 19 - 60 1 49 11 A1 Precision Circlip Pliers straight tips 10 - 25 1 49 11 A2 Precision Circlip Pliers straight tips 19 - 60 1

0020 Precision Circlip Pliers Sets

00 20 03 SB

00 20 04 SB

■ attractive sales packaging with Euro standard perforation ■ contains common Precision Circlip Pliers for highest requirements ■ sturdy plastic packaging, also suitable for storage of the pliers

00 20 03 SB4 parts

00 20 04 SB8 parts


Contents Style TipsØ mm

Quantity

g

00 20 03 SB

050100

Precision Circlip Pliers Set 685

48 11 J1 straight tips 12 - 25 1


49 11 A1 straight tips 10 - 25 1

49 11 A2 straight tips 19 - 60 1 00 20 04 SB

062417

Precision Circlip Pliers Set 1275





48 21 J11 angled tips 12 - 25 1 90°

48 21 J21 angled tips 19 - 60 1

49 21 A11 angled tips 12 - 25 1 90°

49 21 A21 angled tips 19 - 60 1

194

TOOL KITS

0020 Pliers Sets in a foam tray

00 20 01 V01

00 20 01 V02

00 20 01 V03

■ in a foam tray for workbenches and tool trolleys ■ clearly organised storage of tools ■ precisely-sized recesses for holding the pliers ■ foam tray dimensions (L x W x H): 335 x 165 x 33 mm ■ Material: two colour, closed pore foam

00 20 01 V01four pliers in a foam tray

00 20 01 V02six circlip pliers in a foam tray

00 20 01 V03three pliers in a foam tray


Contents Quantity

g

00 20 01 V01

069645

Pliers Set ”Basic“ 4 pliers in a foam tray 1095

03 05 180 Combination Pliers 1 26 15 200 Snipe Nose Side Cutting Pliers 1 74 05 180 High Leverage Diagonal Cutter 1

87 01 250 KNIPEX Cobra® 1 00 20 01 V02

069652

Circlip Pliers Set 6 circlip pliers in a foam tray 915

48 11 J1 Precision Circlip Pliers 1

48 11 J2 Precision Circlip Pliers 1

48 21 J21 Precision Circlip Pliers 1 90° 49 11 A1 Precision Circlip Pliers 1

49 11 A2 Precision Circlip Pliers 1

49 21 A21 Precision Circlip Pliers 1 90° 00 20 01 V03

069669

Water Pump Pliers Set 3 pliers in a foam tray 1065

85 01 250 KNIPEX SmartGrip® 1 87 41 250 Multiple Slip Joint Spanner 1 87 51 250 KNIPEX Cobra® ES 1

195

TOOL KITS

0020 Pliers Sets

00 20 11 00 20 12

00 20 13

■ tools in a plastic deep-drawn tray with transparent lid ■ attractive sales packaging with Euro standard perforation ■ dimensions (W x H x D): 170 x 370 x 40 mm ■ Material: sturdy cardboard packaging, printed

00 20 09 V01pliers with polished heads; handles with non-slip plastic coating or with two-colour multi-components grips

00 20 10pliers with polished heads and plastic coated handles

00 20 11pliers with two-colour multi-component grips

00 20 12pliers VDE-tested in conformance with DIN EN/IEC 60900 1000V, pliers chrome-plated; handles with multi-component grips

00 20 13tools VDE-tested in conformance with DIN EN/IEC 60900 1000V, pliers chrome-plated; handles with multi-component grips


Contents Quantity Nominal size

g

00 20 09 V01

073994

Bestseller Set 950

03 02 180 Combination Pliers

Knipex

1 180 mm 70 02 160 Diagonal Cutter 1 160 mm

87 01 250 KNIPEX Cobra® 1 250 mm 00 20 10

010388

Power Set 990

02 01 180 High Leverage Combination Pliers

Knipex

1 180 mm 74 01 160 High Leverage Diagonal Cutter 1 160 mm 87 01 250 KNIPEX Cobra® 1 250 mm

00 20 11

012405

Assembly Set 935


Knipex

1 180 mm 26 12 200 Snipe Nose Side Cutting Pliers 1 200 mm 70 02 160 Diagonal Cutter 1 160 mm

00 20 12

012412

Electro Set 960


Knipex

1 180 mm 26 16 200 Snipe Nose Side Cutting Pliers 1 200 mm 70 06 160 Diagonal Cutter 1 160 mm

00 20 13

043287

VDE Tool Set 850

26 16 200 Snipe Nose Side Cutting PliersKnipex

1 200 mm 70 06 160 Diagonal Cutter 1 160 mm 006110

Screwdrivers for slotted screwsWera

1 0.6 x 3.5 x 100 mm 006120 1 1.0 x 5.5 x 125 mm

006154Screwdrivers for cross recessed Phillips screws

1 PH2 x 100 mm

00 20 1000 20 09 V01

196

TOOL KITS

0020 Compact-Box 4 parts

with insulated pliers

00 20 15

■ high quality, versatile, shock-resistant plastic case ■ foam insert with honeycomb structure for variable equipment ■ dimensions, exterior (H x W x D): 65 x 327 x 275 mm

00 20 15all pliers VDE tested according to DIN EN/IEC 60900 1000V, pliers finish 6

00 21 15 LEwithout tools


Contents Quantity

g

00 20 15

024804

Compact-Box 4 parts 1430

03 06 180 Combination Pliers 1 11 06 160 Wire Stripper 1 26 16 200 Snipe Nose Side Cutting Pliers 1 70 06 160 Diagonal Cutter 1

00 21 15 LE 045175 530

197

TOOL KITS

0020 Electronics Pliers Sets

for working on electronic components

00 20 16 00 20 16 P

00 20 16 P ESD

00 20 17

00 20 18

00 20 167 parts, contains 6 electronics pliers and one pair of precision tweezers; case made of hard-wearing polyester fabric, pliers are held by elastic band, zippered

00 20 16 P6 parts, contains 6 precision electronics pliers; case made of hard-wearing polyester fabric, pliers are held by elastic band, zippered

00 20 16 P ESD6 parts, contains 6 ESD precision electronics pliers, electrically discharging version; case made of hard-wearing polyester fabric, pliers are held by elastic band, zippered

00 20 176 parts, contains 6 ESD electronics pliers, electrically discharging version; case made of hard-wearing polyester fabric, pliers are held by elastic band, zippered

00 20 188 parts, contains 2 electronics pliers and 6 electronics screwdrivers; practical storage box, shock-resistant plastic, with foam insert

00 20 18 ESD8 parts, contains 2 electronics pliers and 6 electronics screwdrivers, ESD electrically discharging version; practical storage box, shock-resistant plastic, with foam insert


Contents

g

00 20 16 022619 35 12 115 / 35 22 115 / 35 32 115 / 64 32 120 / 77 02 115 / 77 42 115 / 92 34 36 720 00 20 16 P 063223 34 12 130 / 34 22 130 / 34 32 130 / 79 02 120 / 79 02 125 / 79 42 125 575 00 20 16 P ESD 063230 34 12 130 ESD / 34 22 130 ESD / 34 32 130 ESD / 79 02 120 ESD / 79 02 125 ESD / 79 42 125 ESD 58500 20 17 031222 35 12 115 ESD / 35 22 115 ESD / 35 42 115 ESD / 64 32 120 ESD / 77 02 115 ESD / 77 32 115 ESD 695

00 20 18 03307335 22 115 / 77 02 115 / Screwdrivers 0.4 x 2.5 / 0.5 x 3.0 / 0.6 x 3.5 / 0.8 x 4.0 / PH 0 / PH 1

460

00 20 18 ESD 051848 35 22 115 ESD / 77 02 115 ESD / Screwdrivers 0.4 x 2.5 / 0.5 x 3.0 / 0.6 x 3.5 / 0.8 x 4.0 / PH 0 / PH 1

465

00 20 18 ESD

198

TOOL KITS

0020 KNIPEX Minis in belt pouch 2 parts

00 20 72 V01

■ KNIPEX Minis as "little helpers" in a practical belt pouch ■ made of hard-wearing polyester fabric ■ with hook and loop fastener ■ with elastic side holder for small flash lamp, pen or suchlike ■ with practical belt loop ■ dimensions (W x H x D): 70 x 170 x 50 mm


Contents Quantity

g

00 20 72 V01

070832

KNIPEX Minis in belt pouch 2-piece 350

86 03 150 Pliers Wrench 1 87 01 125 KNIPEX Cobra® 1

0021 Tool Bag 24 parts

for electrical contractors, top model

00 21 01 TL

■ contains 24 brand name quality tools, partly VDE tested according to DIN EN/IEC 60900, 1000 V

■ comfortable bag of hard-wearing leather, with front bag, adjustable retaining loops and belt

■ with galvanised steel base tray ■ edges of the tool case reinforced with aluminium ■ dimensions, interior (W x H x D): 420 x 250 x 160 mm



g

00 21 01 TL

032694

Tool Bag 24 parts 6990

306125 PUK® Junior Hacksaw Haunstätter 1 150 x 240 mm


Knipex

1 180 mm

11 06 160 Insulation Stripper 1 160 mm

16 20 165 Dismantling Tool 1 165 mm

25 06 160 Snipe Nose Side Cutting Pliers 1 160 mm

70 06 160 Diagonal Cutter 1 160 mm

98 52 Cable Knife 1 185 mm 7165/50 Plasterer‘s bowl Nölle 1 125 x 90 mm

101-0300 Locksmith‘s hammer

Picard

1 300 g

30490-800 Chipping hammer 1 800 g

75040-015 Flat brush 1 40 mm

75075-040 Painter‘s spatula 1 40 mm

71510-000 Metre ruler (yardstick) 1 2 m

361 252 1 Electrician’s ChiselRennsteig

1 250 x 10 mm

340 300 1 Mason’s Chisels 1

006100


Wera

1 0.4 x 2.5 x 80 mm

006110 1 0.5 x 3.0 x 100 mm

006120 1 1.0 x 5.5 x 125 mm

006125 1 1.2 x 6.5 x 150 mm

006152Screwdrivers for cross recessed Phillips® screws

1 PH1 x 80 mm

006154 1 PH 2 x 100 mm

007620Screwdrivers for slotted screws

1 1.0 x 6.0 x 125 mm

110010 1 1.2 x 6.5 x 150 mm

465608 Voltage Detector 1 0.5 x 3.0 x 70 mm

199

TOOL KITS

0021 Tool Bag 24 parts

apprentices tool bag for electrical contractors

00 21 02 SL


■ front, rear and lid made of calf leather, black ■ semi-fold-out front with adjustable loops and exterior document

compartment ■ front additionally reinforced with aluminium brackets ■ with galvanised steel base tray ■ handle ■ dimensions, interior (W x H x D): 420 x 250 x 160 mm

00 21 02 SLcontains 24 brand name quality tools, partly VDE tested according to DIN EN/IEC 60900, 1000 V




g

00 21 02 SL

050162

Tool Bag 24 parts 6980

306125 PUK® Junior Hacksaw Haunstätter 1 150 x 240 mm


Knipex

1 180 mm 11 05 160 Insulation Stripper 1 160 mm

16 20 165 Dismantling Tool 1 165 mm

25 05 160 Snipe Nose Side Cutting Pliers 1 160 mm 70 05 160 Diagonal Cutter 1 160 mm

98 52 Cable Knife 1 185 mm 7165/50 Plasterer‘s bow Nölle 1 125 x 90 mm

101-0300 Locksmith‘s hammer

Picard

1 300 g

401-1000 Sledge hammer 1 1000 g

75040-015 Flat brush 1 40 mm

75075-040 Painter‘s spatula 1 40 mm

71501-024 Carpenter‘s pencil 1 24 cm

361 252 1 Electrician’s ChiselRennsteig

1 250 x 10 mm

340 250 1 Mason’s Chisels 1 250 mm

031580


Wera

1 0.4 x 2.5 x 80 mm 031582 1 0.6 x 3.5 x 100 mm 031587 1 1.0 x 5.5 x 125 mm 031588 1 1.2 x 6.5 x 150 mm 031601 Screwdrivers for cross recessed

Phillips® screws1 PH1 x 80mm

031603 1 PH2 x 100 mm 031611 Screwdrivers for cross recessed

Pozidriv® screws1 PZ1 x 80 mm

031613 1 PZ2 x 100 mm 005655 Voltage Detector 1 0.5 x 3.0 x 70 mm

00 21 02 LE 057499 2970

200

TOOL KITS

0021 Tool Box 7 parts

for electrical contractors

00 21 15

■ high quality, versatile, shock-resistant plastic case ■ foam insert with honeycomb structure for variable equipment ■ dimensions, exterior (H x W x D): 65 x 327 x 275 mm

00 21 15all pliers and screwdrivers except Water Pump Pliers VDE tested according to DIN EN/IEC 60900




g

00 21 15

042853

Tool Box 7 parts 1520


Knipex

1 180 mm 26 16 200 Snipe Nose Side Cutting Pliers 1 200 mm 70 06 160 Diagonal Cutter 1 160 mm 88 03 180 KNIPEX Alligator® 1 180 mm 006100

Screwdrivers for slotted screwsWera

1 0.4 x 2.5 x 80 mm 006115 1 0.8 x 4.0 x 100 mm


1 PH1 x 80 mm

00 21 15 LE 045175 530

201

TOOL KITS

0021 Tool Case ”Electric“ 20-parts

00 21 20

■ heavy duty ABS material, black ■ with circumferential double aluminium frame ■ register hinges working as lid holder ■ strong, ergonomic handle ■ two flip-locks, lockable ■ one removable tool board in the lid with 15 push-in compartments

on the bottom side and six big push-in compartments and a clamp compartment (400 mm width) on the lid side, fixed by popper

■ base tray, height 58 mm, can be subdivided by flexible inserts; cover plate with six large push-in compartments, can be fixed by popper

■ cover and tool plate made of Con-Pearl® material ■ 20 kg maximum load ■ dimensions, exterior (W x H x D): 480 x 175 x 370 mm

dimensions, interior (W x H x D): 460 x 170 x 310 mm

00 21 20with 20 brand name tools, partly VDE tested according to DIN EN/IEC 60900




g

00 21 20

052166

Tool Case ”Electric“ 20 parts 7225


Knipex

1 180 mm 26 16 200

Snipe Nose Side Cutting Pliers1 200 mm

26 26 200 1 200 mm 40° 70 06 160 Diagonal Cutter 1 160 mm

74 06 200 High Leverage Diagonal Cutter 1 200 mm

95 16 200 Cable Shears 1 200 mm 98 56 Cable Knife 1 185 mm 86 03 180 Pliers Wrench 1 180 mm 87 03 250 KNIPEX Cobra® 1 250 mm 12 40 200 Self-Adjusting Insulation Stripper 1 200 mm

16 80 125 Universal Dismantling Tool 1 125 mm006100


Wera

1 0.4 x 2.5 x 80 mm 006115 1 0.8 x 4.0 x 100 mm 006120 1 1.0 x 5.5 x 125 mm 006125 1 1.2 x 6.5 x 150 mm 006152 Screwdrivers for cross recessed

Phillips® screws1 PH1 x 80 mm



006164 1 PZ2 x 100 mm 005655 Voltage Detector 1 0.5 x 3.0 x 70 mm

00 21 20 LE 044567 4485

202

TOOL KITS

0021 Tool Case for electrical contractors

23 parts

00 21 30

■ contains 23 brand name quality tools, partly VDE tested according to DIN EN/IEC 60900, 1000 V

■ hard-wearing ABS hard-shell construction with aluminium frame and circular buffer protection

■ document compartment and pen holding straps ■ one removable tool plate, with elastic loops on both sides ■ one cover plate with elastic loops and tool protection cloth ■ large base tray with variable separations (e.g. for measuring and

testing devices). Interior dimensions: 420 x 320 x 85 mm ■ sturdy metal locks and 3-digit-lock ■ strong, ergonomic handle ■ feet on both sides ■ colour: silver / aluminium look



g

00 21 30 051084 Tool Case for electrical contractors 23 parts 9440


Knipex

1 180 mm 26 16 200

Snipe Nose Side Cutting Pliers1 200 mm

26 26 200 1 200 mm 40° 70 06 125

Diagonal Cutter1 125 mm

70 06 160 1 160 mm

92 27 62 Precision Tweezers 1 150 mm

98 56 Cable Knife 1 185 mm 00 11 03 Control Cabinet Key 1 76 mm

12 40 200 Self-Adjusting Insulation Stripper 1 200 mm

16 80 125 Universal Dismantling Tool 1 125 mm

86 03 180 Pliers Wrench 1 180 mm 87 03 250 KNIPEX Cobra® 1 250 mm

006100


Wera

1 0.4 x 2.5 x 80 mm

006110 1 0.6 x 3.5 x 100 mm

006115 1 0.8 x 4.0 x 100 mm

006120 1 1.0 x 5.5 x 125 mm

006125 1 1.2 x 6.5 x 150 mm

006130 1 1.2 x 8.0 x 175 mm


1 PH0 x 80 mm 006152 1 PH1 x 80 mm



006164 1 PZ2 x 100 mm

203

TOOL BAGS AND TOOL CASES

0019 Belt Pouch for two pliers

00 19 72 LE

00 19 73 LE

■ for two pliers up to 150 mm length ■ made of hard-wearing polyester fabric ■ with hook and loop fastener ■ with elastic side holder for flash lamp, pen or suchlike ■ with practical belt loop


Widthmm

Heightmm

Depthmm g

00 19 72 LE 070191 65 155 25 65

0019 Belt Tool Pouch empty ■ made of hard-wearing polyester fabric and leather

■ with pockets for up to 8 tools ■ tool loops made of leather, riveted ■ with snap hook


Widthmm

Heightmm

Depthmm g

00 19 73 LE 072065 170 235 75 210

0021 Tool Bag “New Classic Basic“ empty

00 21 02 LE


■ front, rear and lid made of calf leather, black ■ front additionally reinforced with aluminium brackets ■ semi-fold-out front with adjustable loops and exterior

document compartment ■ with galvanised steel base tray ■ handle ■ dimensions, exterior (W x H x D): 450 x 300 x 190 mm;


DimensionArticle No. EAN

4003773- exterior (interior) width mm exterior (interior) height

mm exterior (interior) depth

mm g

00 21 02 LE 057499 450 (420) 300 (250) 190 (160) 2970

204


0021 Tool Case “Basic“ empty

00 21 05 LE

■ heavy duty ABS material, black ■ circumferential aluminium frame with D-shape rings for the

shoulder strap (included)■ 3-digit lock and two flip-locks for fixation of the cover ■ strong, ergonomic handle ■ metal hinges ■ lid holder with hinge-joint mechanism ■ document compartment in the cover ■ removable tool board in the lid with nine push-in compartments and

an elastic loop on the lid side; with ten slim and one large push in compartments on the bottom side

■ base tray, height 55 mm, can be subdivided by inserts; cover plate with 12 large push-in compartments and a flat compartment, can be fixed by popper

■ load capacity: 15 kg ■ dimensions, exterior (W x H x D): 465 x 200 x 410 mm dimensions

exterior (W x H x D): 440 x 180 x 350 mm


4003773-exterior (interior) width

mmexterior (interior) height mm exterior (interior) depth

mm g

00 21 05 LE 056904 465 (440) 200 (180) 410 (350) 5680

0021 Tool Case “Standard“ empty

00 21 20 LE

■ heavy duty ABS material, black ■ with circumferential double aluminium frame ■ register hinges working as lid holder ■ strong, ergonomic handle ■ two flip-locks, lockable ■ one removable tool board in the lid with 15 push-in compartments

on the bottom side and six big push-in compartment and a clamp compartment (400 mm width) on the lid side, fixed by popper

■ base tray, height 58 mm, can be subdivided by flexible inserts; cover plate with six large push-in compartments, can be fixed by popper

■ cover and tool plate made of Con-Pearl® material ■ 20 kg maximum load ■ dimensions, exterior (W x H x D): 480 x 175 x 370 mm dimensions,

interior (W x H x D): 460 x 170 x 310 mm


4003773-exterior (interior) width mm exterior (interior) height

mmexterior (interior) depth

mm g

00 21 20 LE 044567 480 (460) 175 (170) 370 (310) 4485

205


0021 Tool Case “Classic II“ empty

00 21 32 LE

■ heavy duty ABS material, black ■ with circumferential double aluminium frame ■ register hinges working as lid holder ■ sturdy multi-component handle with grip recesses ■ two flip-locks, lockable ■ document compartment in the cover ■ one removable tool board in the lid with CP7-tool holder

(thickness 11 mm) on the bottom side ■ one tool board in the lid with CP7-tool holder (thickness 11 mm)

on the lid side and CP7-tool holder (thickness 15 mm) on the bottom side

■ base tray, height 58 mm, can be subdivided by flexible inserts; cover plate with CP7-tool holder (thickness 25 mm) on the lid side, can be fixed by popper

■ cover and tool plate made of Con-Pearl® material ■ 30 kg maximum load ■ dimensions, exterior(W x H x D): 480 x 177 x 370 mm




mmexterior (interior) height


mm g

00 21 32 LE 057536 480 (460) 180 (165) 365 (300) 5235

0021 Tool Case “Classic III“ empty

00 21 33 LE

■ heavy duty ABS material, black ■ extra large in height, width and depth ■ with circumferential double aluminium frame ■ register hinges working as lid holder ■ sturdy multi-component handle with grip recesses ■ two flip-locks, lockable ■ document compartment in the cover ■ one tool board in the lid with 13 push-in compartments on the

bottom side and twelve push-in compartments as well as a clamp compartment (width 400 mm) on the lid side

■ base tray, height 88 mm, can be subdivided by flexible inserts; cover plate with 15 push-in compartments and a clamp compartment (width 400 mm), can be fixed by 2 poppers

■ cover and tool plate made of Con-Pearl® material ■ 30 kg maximum load ■ dimensions, exterior (W x H x D): 490 x 205 x 420 mm dimensions,

interior (W x H x D): 470 x 180 x 360 mm





mm g

00 21 33 LE 057543 490 (470) 205 (180) 420 (360) 5620

206


0021 Tool Case ”BIG Twin“ empty

00 21 40 LE

00 21 40 T





mm g

00 21 40 LE 057673 490 (445) 255 (105 + 105) 410 (350) 7550

00 21 40 T 062981 Trolley for rolling case transport

00 21 40 LE■ heavy duty ABS material, black■ sturdy aluminium frame with D-shape rings for belt and fix, sturdy

centre board with multi-purpose push-in facilities by elastic loops and twelve small pockets

■ comfortable handle and mounting device for a "Trolley" embedded in the bottom (available ordering ref. 00 21 40 T)

■ metal hinges■ 30 kg maximum load■ can be opened on one or both sides; bottom tray and cover can

be opened independently■ stands stable in any opening position due to lid-holders and hinge

mechanisms on both sides, that register in a position of 45° and 90°■ 3-digit lock and two flip-locks for fixation of the cover■ removable document compartment and removable tool board,

with 13 push-in compartments on one side■ two flip-locks to fix the bottom■ base tray, height 58 mm, can be subdivided by flexible inserts;

cover plate with six large push-in compartments, can be fixed by popper

■ dimensions, exterior ( W x H x D): 490 x 255 x 410 mm dimensions, interior (W x H x D) : 445 x (105 + 105) x 350 mm

00 21 40 T■ telescopic handle for rolling transport of tool case■ applicable for cases:

00 21 40 LE Tool Case "BIG Twin", 98 99 14 Universal Tool Case■ height adjustable handle with catch■ integrated mechanism for fixation to the case, for rapid assembly

and removal■ with two smooth castors■ dimensions: 60 x 245 x 400 (1,000) mm (extended)

207


0021 Tool Case “BIG Twin-Move“

with integrated rollers and telescopic handle

empty

00 21 41 LE

■ heavy duty ABS material, black ■ all-round aluminium frame and firmly mounted sturdy centre board,

each side offering multi-purpose push-in facilities by elastic loops and 12 small pockets

■ pull-out handle embedded in the base and two integrated smooth in-line skater runners

■ 30 kg maximum load ■ can be opened on one or both sides (V form); base tray and cover

can be partially or fully opened independently of each other; stands securely in all opening positions; the special runners are gentle to the floor and ensure stability

■ lockable ■ removable document compartment and removable tool panel with

13 tool pouches ■ base tray, height 60 mm, can be subdivided by flexible inserts; tool

panel as cover plate with 13 tool pouches ■ dimensions, exterior (W x H x D): 510 x 270 x 410 mm ■ dimensions, lid, interior (W x H x D): 480 x 105 x 370 mm ■ dimensions, base, interior (W x H x D): 445 x 105 x 330 mm





mm g

00 21 41 LE 071549 510 (480/445) 270 (105) 410 (370/330) 8600

208

SALES AIDS

0019 Test Supports

00 19 20 00 19 20 T 00 19 21 T

00 19 20for testing the self-locking function of the “Alligator®“ and “Cobra®“ Water Pump Pliers; steady stand, high stability; without pliers

00 19 20 Tfor testing the self-locking function of the “Alligator®“ and “Cobra®“ Water Pump Pliers; collapsible for space saving transport; without pliers

00 19 21 Tfor testing the ratchet principle of Pliers Wrenches; can be fixed on the wall; without pliers


Widthmm

Heightmm

Depthmm g

00 19 20 024637 230 165 310 1385

00 19 20 T 031192 140 225 135 810

00 19 21 T 027461 85 85 150 728

0019 Sales Display

00 19 24

C320 00187

■ for 5 x 6 pliers ■ small size, minimum space required at the point of sales ■ with informative header and slide-in strip for product detail labels ■ assortment on request ■ when ordering, do always ask for product detail header (see table)

and product detail labels ■ without pliers ■ Material: steel wire, silver powder coated


Widthmm

Heightmm

Depthmm g

00 19 24 029656 325 415 190 925

C320 00110 051473 Header general programme

C320 00187 603009 Header Comfort, for pliers with multi-component grips

209

SALES AIDS

0019 Sales Display

00 19 25

C320 00176

C320 00231

■ for 8 x 7 pliers ■ solid style; can be fixed on tool

bar systems, also suitable as counter display

■ with explanatory header ■ assortment on request ■ when ordering do always ask

for product detail header (see table)

■ without pliers ■ Material: sheet steel / steel

wire, silver powder coated


Widthmm

Heightmm

Depthmm g

00 19 25 014027 490 400 310 4140

C320 00132 601807 Header general programme

C320 00176 602927 Header Comfort, for pliers with multi-component grips

C320 00231 051428 Header Precision Circlip Pliers 48/49

0019 Rotary Sales Stand

00 19 28

■ for 16 x 3 pliers ■ attractive, compact rotary construction for the counter ■ with 16 hooks 00 19 33 ■ assortment on request ■ when ordering, do always ask for product detail labels ■ without pliers ■ Material: sheet steel / steel wire, silver powder coated


Diametermm

Heightmm g

00 19 28 032083 400 610 5950

210

SALES AIDS

0019 Tool Bars (Pegboards) and Accessories

00 19 30 00 19 30 66

00 19 30 2

00 19 30 15

00 19 30 16

00 19 30 19

00 19 30for the promotional, extensive product presentation; completely with supports, 5 peg boards, shelf and illuminated transparent advertising fascia panel; can be equipped either with pliers on hooks, carded pliers and/or sales displays; with power cable and 230 V plug; Material: sheet steel/ steel tubing, silver powder coated

00 19 30 3for the promotional, extensive product presentation; completely with supports, 5 peg boards, shelf; without illuminated transparent advertising facia; can be equipped either with pliers on hooks, carded pliers and/or sales displays; Material: sheet steel/ steel tubing, silver powder coated

00 19 30 66for the space saving presentation; completely with supports, 5 peg boards, shelf; without illuminated transparent advertising fascia panel; with magnetic advertising fascia panel; can be equipped either with pliers on hooks, carded pliers and/or sales displays; Material: sheet steel/ steel tubing, silver powder coated

00 19 30 17

00 19 30 20

00 19 30 17


Widthmm

Heightmm

Depthmm g

00 19 30 024644 Tool Bar with illuminated fascia panel 1000 2200 500 58000 00 19 30 3 052524 Toolbar without illuminated fascia panel 1000 2200 500 4700000 19 30 66 055211 Tool Bar 660 2200 500 40000 00 19 30 2 046783 Illuminated fascia panel, to affix to tool bar systems 1000 200 400 914000 19 30 15 071891 Magnetic label for tool bar 980 100 31000 19 30 16 071907 Magnetic label for tool bar 980 100 310 00 19 30 19 071938 Magnetic label for tool bar 980 200 61000 19 30 17 071914 Magnetic label for tool bar 00 19 30 66 650 100 410 00 19 30 18 071921 Magnetic label for tool bar 00 19 30 66 650 100 41000 19 30 20 071945 Magnetic label for tool bar 00 19 30 66 650 200 410

211

SALES AIDS

0019 Show-Cabinets for product presentation

for assembly to tool bar systems

00 19 30 VIT 00 19 30 VIT 1

■ with two glass sliding doors, lockable ■ illumination unit with plug for series connection ■ with power cable and 230 V plug ■ Material: aluminium section, silver colour

00 19 30 VIThanging show-cabinet for assembly on tool bar systems; with shelf, top cover and transparent advertising fascia panel; easy to assemble collapsible frame construction

00 19 30 VIT 1basic show-cabinet for assembly to tool bar systems; with top cover and transparent advertising fascia panel

00 19 30 VIT 2unit show-cabinet for assembly to tool bar systems, for extension of basic show-cabinet 00 19 30 VIT1; with top cover and transparent advertising fascia panel


Designation Widthmm

Heightmm

Depthmm g

00 19 30 VIT 034186 Hanging Show-Cabinet for Tool Bar 1000 1200 400 39000

00 19 30 VIT 1 048978 Basic Show-Cabinet for Product Presentation 1000 2000 400 59000

00 19 30 VIT 2 048985 Unit Show-Cabinet for 00 19 30 VIT - Expansion Module 1000 2000 400 51000

212

SALES AIDS

0019 Hooks for pegboards

00 19 31

00 19 33 00 19 33 2

00 19 35 100 19 35 3

00 19 35 2

00 19 31160 mm length; for 6 pliers, with face plate for label; when ordering, do always ask for product detail labels

00 19 3390 mm length; for 3 pliers, with faceplate for label; when ordering, do always ask for product detail labels

00 19 33 2200 mm length; heavy duty for mounting pipe wrenches, etc.; with pivoting clamping device for easy fastening and release

00 19 35 1 / 00 19 35 3200 mm length; for self-service packs with Euro standard perforations; with pivoting clamping device for easy fastening and release

00 19 35 250 mm length; for self-service (carded) packs and leaflets with Euro standard perforations


Designation Hole spacingmm

Depthmm g

00 19 31 014874 for 6 pliers 30 160 93

00 19 33 014881 for 3 pliers 30 90 70

00 19 33 2 042112 for large size water pump pliers, pipe wrenches, etc. 30 200 150

00 19 35 1 045168 for self-service packs 25 200 93

00 19 35 2 028284 for brochures + carded tools 30 50 10

00 19 35 3 051787 for self-service packs 30 200 95

0019 Brochure Holder for pegboards

00 19 36

■ for approx. 250 A4-size leaflets■ Material: steel wire, silver powder coated


Widthmm

Heightmm

Depthmm g

00 19 36 024682 230 290 90 80

213

SALES AIDS

0019 Pliers Racks for pegboards

00 19 34

00 19 34 1

00 19 34 2

00 19 32for 3 x 6 pliers

00 19 34for 5 x 6 pliers

00 19 34 1for 5 x 6 carded pliers; with header sign

00 19 34 2for 15 x 6 pliers


Designation Widthmm

Heightmm

Depthmm g

00 19 32 024651 for 3 x 6 pliers 195 98 175 344

00 19 34 024668 for 5 x 6 pliers 325 98 175 400

00 19 34 1 051824 for 5 x 6 carded pliers 480 200 225 1065

00 19 34 2 052364 for 15 x 6 pliers 995 145 215 2250

214

SALES AIDS

0019 Sales Displays

00 19 34 3for pliers finish 0; 1; 3 or 4


Designation Widthmm

Heightmm

Depthmm g

00 19 34 3 054450 for 3 x 6 pliers; for pliers finish 0/1/3 or 4 240 320 310 2345

00 19 34 4 054467 for 3 x 6 pliers; for pliers finish 2/5/6 240 320 310 2340

C320 00275 054535 Header Precision Circlip Pliers 48/49

C320 00286 054504 Header Concretors‘ Nippers

C320 00297 054481 Header Cobra®; Pliers Wrenches

C320 00319 054498 Header Stripping, Crimping

C320 00330 054511 Header General Programme

C320 00352 060284 Header Multiple Slip Joint Spanners

C320 00363 060291 Header Self-adjusting Insulation Strippers

C320 00429 062271 Header for 74 12

C320 00451 063032 Header Cobra® ES

C320 00462 063049 Header SmartGrip®

C320 00517 065869 Header Lineman‘s Pliers

C320 00528 065876 Header Insulated Pliers Wrenches

C320 00605 070214 Header KNIPEX Alligator®

00 19 34 4for pliers finish 2; 5 or 6

215

SALES AIDS

C320 00275 C320 00286 C320 00297

C320 00330 C320 00352 C320 00462

C320 00517 C320 00605

INDEX ARTICLE NUMBER / PAGE

00 11 02 18800 11 03 18800 11 04 18800 11 06 18800 11 07 18900 11 08 18900 11 17 19000 19 12 V01 19100 19 12 V02 19100 19 12 V03 19100 19 19 V01 19100 19 19 V02 19100 19 19 V03 19100 19 19 V04 19100 19 19 V05 19100 19 19 V06 19100 19 19 V07 19100 19 19 V08 19100 19 19 V09 19100 19 19 V10 19100 19 19 V11 19100 19 19 V12 19100 19 19 V13 19100 19 20 20800 19 20 T 20800 19 21 T 20800 19 24 20800 19 25 20900 19 28 20900 19 29 19200 19 30 21000 19 30 2 21000 19 30 3 21000 19 30 15 21000 19 30 16 21000 19 30 17 21000 19 30 18 21000 19 30 19 21000 19 30 20 21000 19 30 66 21000 19 30 VIT 21100 19 30 VIT 1 21100 19 30 VIT 2 21100 19 31 21200 19 32 21300 19 33 21200 19 33 2 21200 19 34 21300 19 34 1 21300 19 34 2 21300 19 34 3 21400 19 34 4 21400 19 35 1 21200 19 35 2 21200 19 35 3 21200 19 36 21200 19 41 19200 19 56 19300 19 57 19300 19 72 LE 20300 19 73 LE 20300 20 01 V01 19400 20 01 V02 19400 20 01 V03 19400 20 03 SB 19300 20 04 SB 19300 20 09 V01 19500 20 10 19500 20 11 19500 20 12 19500 20 13 19500 20 15 19600 20 16 19700 20 16 P 19700 20 16 P ESD 19700 20 17 19700 20 18 19700 20 18 ESD 19700 20 72 V01 19800 21 01 TL 19800 21 02 LE 20300 21 02 SL 19900 21 05 LE 20400 21 15 20000 21 15 LE 196/20000 21 20 20100 21 20 LE 201/20400 21 30 20200 21 32 LE 20500 21 33 LE 205

00 21 40 LE 20600 21 40 T 187/20600 21 41 LE 20701 06 160 20/15601 06 190 20/15602 01 180 2102 01 200 2102 01 225 2102 02 180 2102 02 200 2102 02 225 2102 05 180 2102 05 200 2102 05 225 2102 06 180 21/15602 06 200 21/15602 06 225 21/15602 07 200 21/15602 07 225 21/15603 00 180 2203 00 200 2203 00 250 2203 01 140 2203 01 160 2203 01 180 2203 01 200 2203 01 250 2203 02 160 2203 02 180 2203 02 200 2203 05 140 2203 05 160 2203 05 180 2203 05 200 2203 06 160 22/15703 06 180 22/15703 06 200 22/15703 07 160 22/15703 07 180 22/15703 07 200 22/15703 07 250 22/15708 05 110 2009 01 240 2309 02 240 2309 11 240 2309 12 240 2311 01 160 2411 02 160 2411 05 160 2411 06 160 24/15711 07 160 24/15711 12 160 2411 15 160 2411 17 160 24/15711 82 130 2511 92 140 2512 11 180 2512 12 02 2612 12 06 2612 12 10 2612 12 11 2612 12 12 2612 19 02 2612 19 06 2612 19 10 2612 19 11 2612 19 12 2612 19 180 2512 21 180 2512 29 180 2512 40 200 2812 42 195 2912 49 01 2812 49 02 2812 49 03 2812 49 21 2912 49 23 2912 50 200 2812 59 01 2812 59 02 2812 62 180 3012 64 180 3012 69 21 3012 69 23 3012 69 31 3012 80 040 SB 3112 80 100 SB 3112 82 130 SB 3112 85 100 SB 3213 01 160 32

50 01 210 6250 01 225 6250 01 250 6250 01 300 6251 01 210 6255 00 300 6357 00 360 6358 10 225 6358 30 225 6361 01 200 6761 02 200 6762 12 120 6764 01 115 6964 02 115 6964 11 115 6964 12 115 6964 12 115 ESD 7064 22 115 6964 32 120 6964 32 120 ESD 7064 42 115 6964 52 115 6964 62 120 6964 62 120 ESD 7064 72 120 6967 01 140 7167 01 160 7167 01 200 7167 05 140 7167 05 160 7167 05 200 7168 01 160 7168 01 180 7168 01 200 7169 01 130 7169 03 130 7170 01 110 7370 01 125 7370 01 140 7370 01 160 7370 01 180 7370 02 125 7370 02 140 7370 02 160 7370 02 180 7370 04 140 7370 05 125 7370 05 140 7370 05 160 7370 05 180 7370 06 125 73/16170 06 140 73/16170 06 160 73/16170 06 180 73/16170 07 160 73/16170 07 180 73/16170 11 110 7370 15 110 7370 26 160 73/16171 01 200 7571 02 200 7571 12 200 7571 21 200 7571 22 200 7571 31 200 7571 32 200 7571 41 200 7571 72 460 7671 72 610 7671 72 760 7671 72 910 7671 79 460 7671 79 610 7671 79 760 7671 79 910 7671 82 950 7771 89 950 7772 01 140 7872 01 160 7872 01 180 7872 02 125 7872 11 160 7872 21 160 7872 51 160 7974 01 140 8174 01 160 8174 01 180 8174 01 200 8174 01 250 8174 02 140 81

13 02 160 3213 05 160 3213 72 160 SB 3314 22 160 3314 25 160 3314 26 160 33/15815 11 120 3415 19 005 3415 19 006 3415 19 008 3415 19 010 3415 51 160 3415 61 160 3415 81 160 3416 20 16 SB 3416 20 28 SB 3416 20 165 SB 3416 29 165 3416 30 135 SB 3516 39 135 3516 40 150 3516 49 150 3516 60 05 SB 3616 60 100 SB 3616 65 125 SB 3716 80 125 SB 3716 85 125 SB 3719 01 130 3819 03 130 3820 01 125 3820 01 140 3820 01 160 3820 01 180 3820 01 200 3820 02 140 3820 02 160 3820 05 140 3820 05 160 3820 06 160 38/15822 01 125 3922 01 140 3922 01 160 3922 01 180 3922 02 140 3922 02 160 3922 05 140 3922 05 160 3922 06 160 39/15922 07 160 39/15923 01 140 3925 01 125 4025 01 140 4025 01 160 4025 02 140 4025 02 160 4025 03 125 4025 03 160 4025 05 140 4025 05 160 4025 06 160 40/15925 21 160 4025 25 160 4025 26 160 40/15926 11 200 4126 12 200 4126 13 200 4126 15 200 4126 16 200 41/16026 17 200 41/16026 21 200 4126 22 200 4126 23 200 4126 25 200 4126 26 200 41/16026 27 200 41/16027 01 160 4228 01 200 4228 21 200 4229 11 160 4329 21 160 4329 25 160 4330 11 140 4430 11 160 4430 11 190 4430 13 140 4430 13 160 4430 15 140 4430 15 160 4430 15 190 4430 16 160 44/160

30 21 140 4430 21 160 4430 21 190 4430 23 140 4430 25 140 4430 25 160 4430 25 190 4430 31 140 4430 31 160 4430 33 160 4430 35 140 4430 35 160 4430 36 160 44/16030 41 160 4531 11 160 4331 15 160 4331 21 160 4331 25 160 4332 11 135 4532 21 135 4532 23 135 4532 31 135 4533 01 160 4533 03 160 4534 12 130 4634 12 130 ESD 4734 22 130 4634 22 130 ESD 4734 32 130 4634 32 130 ESD 4735 11 115 4835 12 115 4835 12 115 ESD 4935 21 115 4835 22 115 4835 22 115 ESD 4935 31 115 4835 32 115 4835 32 115 ESD 4935 42 115 4835 42 115 ESD 4935 52 145 4835 62 145 4835 72 145 4835 82 145 4836 12 130 5036 22 125 5036 32 125 5037 11 125 5137 13 125 5137 21 125 5137 23 125 5137 31 125 5137 33 125 5137 41 125 5137 43 125 5138 11 200 5338 15 200 5338 21 200 5338 25 200 5338 31 200 5338 35 200 5338 41 190 5338 45 190 5338 71 200 5338 91 200 5338 95 200 5340 04 180 5440 04 250 5441 04 180 5441 04 250 5441 04 300 5441 14 250 5441 24 225 5441 34 165 5442 14 280 5542 24 280 5542 34 280 5544 10 J5 5844 10 J6 5844 11 J0 5644 11 J1 5644 11 J2 5644 11 J3 5644 11 J4 5644 13 J0 5644 13 J1 5644 13 J2 5644 13 J3 5644 13 J4 56

44 19 J5 5844 19 J6 5844 20 J51 5844 20 J61 5844 21 J01 5644 21 J11 5644 21 J21 5644 21 J31 5644 21 J41 5644 23 J01 5644 23 J11 5644 23 J21 5644 23 J31 5644 29 J51 5844 29 J61 5844 31 J02 5644 31 J12 5644 31 J22 5644 31 J32 5644 31 J42 5645 10 170 5845 21 200 5846 10 A5 5946 10 A6 5946 11 A0 5746 11 A1 5746 11 A2 5746 11 A3 5746 11 A4 5746 11 G0 5946 11 G1 5946 11 G2 5946 11 G3 5946 11 G4 5946 13 A0 5746 13 A1 5746 13 A2 5746 13 A3 5746 19 A5 5946 19 A6 5946 20 A51 5946 20 A61 5946 21 A01 5746 21 A11 5746 21 A21 5746 21 A31 5746 21 A41 5746 23 A01 5746 23 A11 5746 23 A21 5746 23 A31 5746 29 A51 5946 29 A61 5946 31 A02 5746 31 A12 5746 31 A22 5746 31 A32 5746 31 A42 5748 11 J0 6048 11 J1 6048 11 J2 6048 11 J3 6048 11 J4 6048 21 J01 6048 21 J11 6048 21 J21 6048 21 J31 6048 21 J41 6049 11 A0 6149 11 A1 6149 11 A2 6149 11 A3 6149 11 A4 6149 21 A01 6149 21 A11 6149 21 A21 6149 21 A31 6149 21 A41 6149 31 A0 6149 41 A01 6150 00 130 6250 00 160 6250 00 180 6250 00 210 6250 00 225 6250 00 250 6250 00 300 6250 01 130 6250 01 160 6250 01 180 62

74 02 160 8174 02 180 8174 02 200 8174 02 250 8174 05 140 8174 05 160 8174 05 180 8174 05 200 8174 05 250 8174 06 160 81/16174 06 180 81/16174 06 200 81/16174 06 250 81/16174 07 200 81/16174 07 250 81/16174 12 160 8174 12 180 8174 21 160 8174 21 180 8174 21 200 8174 21 250 8174 22 200 8174 22 250 8174 91 250 7975 02 125 8275 12 125 8275 22 125 8275 52 125 8276 01 125 8376 03 125 8376 05 125 8376 12 125 8376 22 125 8376 81 125 8377 01 115 8477 01 130 8477 02 115 8477 02 115 ESD 8577 02 130 8477 11 115 8477 12 115 8477 12 115 ESD 8577 21 115 8477 21 130 8477 22 115 8477 22 115 ESD 8577 22 130 8477 32 115 8477 32 115 ESD 8577 42 115 8477 42 115 ESD 8577 42 130 8477 52 115 8477 52 115 ESD 8577 72 115 8477 72 115 ESD 8578 03 125 8778 03 125 ESD 8878 13 125 8778 13 125 ESD 8878 23 125 8778 31 125 8778 41 125 8778 61 125 8778 61 125 ESD 8878 71 125 8778 71 125 ESD 8878 81 125 8778 91 125 8779 02 120 9079 02 120 ESD 9179 02 125 9079 02 125 ESD 9179 12 125 9079 12 125 ESD 9179 22 120 9079 22 120 ESD 9179 22 125 9079 22 125 ESD 9179 32 125 9079 32 125 ESD 9179 42 125 9079 42 125 ESD 9179 52 125 9079 52 125 ESD 9179 62 125 9079 62 125 ESD 9181 03 230 9281 13 230 9281 19 230 92

92 02 55 11492 08 78 ESD 11792 08 79 ESD 11792 12 52 11392 22 04 11392 22 06 11392 22 07 11392 22 12 11492 22 13 11492 22 35 11392 23 05 11392 24 01 11392 24 34 11492 27 61 116/16492 27 62 11692 27 62 16492 28 69 ESD 11792 28 70 ESD 11792 28 71 ESD 11792 28 72 ESD 11792 32 29 11592 34 28 11592 34 36 11592 34 37 11592 37 64 117/16492 38 75 ESD 11792 44 42 11592 52 23 11492 58 74 ESD 11792 64 43 11592 64 44 11592 67 63 116/16492 69 84 11592 70 46 11592 72 45 11592 78 77 ESD 11792 84 18 11592 88 73 ESD 11792 94 91 11692 95 89 11692 95 90 11694 10 185 11894 15 215 11894 19 185 11894 19 215 11894 35 215 11895 02 10 11995 02 21 11995 03 160 SB 11995 05 140 12095 05 165 12095 05 185 12095 05 190 12095 06 230 120/16495 11 165 12295 11 200 12395 12 165 12295 12 200 12395 12 500 12495 16 165 122/16595 16 200 123/16695 17 200 123/16695 17 500 124/16795 21 165 12295 21 600 12495 22 165 12295 26 165 122/16595 27 600 124/16795 29 600 124/16795 31 250 12595 31 280 12595 32 038 12695 32 060 12795 32 100 12795 36 250 125/16895 36 280 125/16895 39 038 12695 39 250 125/16895 39 280 125/16895 39 720 12795 39 870 12795 61 150 12995 61 190 12895 62 190 12895 71 445 12995 71 600 12995 77 600 129/16895 79 445 12995 79 600 129/16895 81 600 129

95 89 600 12997 00 215 A 13097 00 215 B 13097 00 215 D 13097 21 215 13097 21 215 B 13097 21 215 C 13097 22 240 13097 32 225 13197 33 01 13397 33 02 13397 39 05 13397 39 06 13397 39 08 13397 39 13 13397 39 30 13397 39 90 13397 40 10 13197 43 05 13497 43 06 13497 43 200 13497 43 200 A 13497 49 04 13597 49 05 13597 49 06 13597 49 08 13597 49 09 13597 49 13 13597 49 15 13597 49 16 13597 49 18 13597 49 19 13597 49 20 13597 49 23 13597 49 24 13597 49 30 13597 49 35 13597 49 40 13597 49 44 13597 49 50 13597 49 54 13597 49 59 135/15097 49 59 1 13697 49 60 13597 49 62 135/15097 49 63 135/15097 49 64 13597 49 65 135/15097 49 65 1 136/15097 49 65 2 136/15097 49 66 135/15097 49 66 1 136/15097 49 66 2 13697 49 66 4 135/15097 49 66 6 135/15097 49 67 135/15097 49 68 135/15097 49 68 1 136/15097 49 69 1 135/15097 49 69 2 135/15097 49 69 11 136/15097 49 70 13597 49 74 13597 49 76 13597 49 81 13597 49 82 13697 49 83 13697 49 84 13697 49 87 13697 49 90 13697 49 93 13697 49 94 136/13997 49 94 14197 49 95 136/13997 49 95 14197 50 01 13797 51 04 13797 51 10 13897 51 12 13897 52 04 13997 52 05 13997 52 06 13997 52 08 13997 52 09 13997 52 10 13997 52 13 13997 52 14 14097 52 19 13997 52 20 14097 52 23 139

97 52 30 14197 52 33 14197 52 34 14197 52 35 14197 52 36 14197 52 37 14197 52 38 14197 52 50 14197 52 63 14397 52 63 DG 14397 52 64 14397 52 65 14397 52 65 A 14397 52 65 DG 14397 52 65 DG A 14397 53 04 14497 53 08 14597 53 09 14597 53 14 14497 54 24 14697 59 06 13797 59 06 13897 59 12 13897 59 14 14097 59 65 2 13697 59 65 2 14397 61 145 A 14697 61 145 F 14697 62 145 A 14697 68 145 A 14697 68 145 A 16997 71 180 14797 72 180 14797 81 180 14797 90 00 14897 90 01 14897 90 05 14997 90 06 14997 90 09 14997 90 10 14997 90 12 14997 90 21 14897 90 22 14897 90 23 14997 90 24 14997 91 01 15097 91 02 15197 91 02 LE 15197 99 01 15297 99 02 15297 99 03 15297 99 04 15297 99 05 15297 99 06 15297 99 07 15297 99 08 15297 99 09 15297 99 10 15297 99 11 15297 99 12 15297 99 13 15297 99 14 15297 99 15 15297 99 16 15297 99 17 15297 99 18 15297 99 19 15297 99 20 15297 99 21 15297 99 22 15297 99 23 15297 99 24 15297 99 25 15297 99 26 15297 99 27 15297 99 28 15297 99 29 15297 99 30 15297 99 31 15297 99 32 15297 99 33 15297 99 34 15297 99 35 15297 99 36 15297 99 37 15297 99 38 15297 99 40 15297 99 41 15297 99 42 15297 99 43 152

97 99 44 15297 99 45 15297 99 46 15297 99 47 15297 99 48 15297 99 49 15297 99 70 15297 99 71 15297 99 72 15297 99 73 15297 99 74 15297 99 75 15297 99 76 15297 99 77 15297 99 78 15297 99 79 15297 99 92 15297 99 93 15297 99 95 15297 99 96 15298 00 1 1/16“ 17098 00 1/2“ 17098 00 1/4“ 17098 00 3/4“ 17098 00 3/8“ 17098 00 5/8“ 17098 00 5/16“ 17098 00 07 17098 00 7/16“ 17098 00 08 17098 00 09 17098 00 9/16“ 17098 00 10 17098 00 11 17098 00 12 17098 00 13 17098 00 14 17098 00 15 17098 00 16 17098 00 17 17098 00 18 17098 00 19 17098 00 22 17098 00 24 17098 00 27 17098 01 07 17198 01 08 17198 01 09 17198 01 10 17198 01 11 17198 01 12 17198 01 13 17198 01 14 17198 01 15 17198 01 16 17198 01 17 17198 01 18 17198 01 19 17198 01 22 17198 01 24 17198 03 04 17298 03 05 17298 03 06 17298 03 07 17298 03 08 17298 03 09 17298 03 10 17298 03 11 17298 03 12 17298 03 13 17298 03 055 17298 04 08 172

98 45 125 17698 45 250 17698 47 1“ 17798 47 1/2“ 17798 47 3/4“ 17798 47 5/8“ 17798 47 7/8“ 17798 47 9/16“ 17798 47 10 17798 47 11 17798 47 11/16“ 17798 47 12 17798 47 13 17798 47 14 17798 47 16 17798 47 17 17798 47 18 17798 47 19 17798 47 22 17798 47 24 17798 47 27 17798 49 05 17998 49 06 17998 49 08 17998 52 18098 53 03 18098 53 13 18098 54 18098 55 18098 56 18198 56 09 18198 60 04 18198 62 01 18198 62 02 18198 64 02 18298 65 01 18298 65 02 18298 65 03 18298 65 10 18298 65 20 18298 65 30 18298 65 40 18298 65 41 18298 67 05 18398 67 10 18398 90 18398 99 11 18398 99 12 18498 99 13 18598 99 14 18798 99 14 LE 18799 00 200 6499 00 220 6499 00 220 K12 6499 00 250 6499 00 280 6499 00 300 6499 01 200 6499 01 220 6499 01 250 6499 01 280 6499 01 300 6499 04 220 6499 04 250 6499 04 280 6499 10 250 6599 10 300 6599 11 250 6599 11 300 6599 14 250 6599 14 300 65

98 04 10 17298 04 13 17298 04 17 17298 04 19 17298 04 22 17298 05 13 17298 05 17 17298 05 19 17298 07 250 17398 13 20 17398 13 25 17398 13 30 17398 13 40 17398 13 50 17398 13 60 17398 14 05 17498 14 06 17498 14 08 17498 15 05 17498 15 06 17498 15 08 17498 20 10 17498 20 25 17498 20 30 17498 20 35 17498 20 40 17498 20 55 17498 20 65 17498 20 80 17498 21 45 17498 24 00 17598 24 01 17598 24 02 17598 24 03 17598 24 04 17598 25 00 17598 25 01 17598 25 02 17598 25 03 17598 25 04 17598 26 10 17598 26 15 17598 26 20 17598 26 25 17598 26 30 17598 30 17698 31 17698 33 25 17998 33 50 17998 35 125 17698 35 250 17698 37 1/2“ 17798 37 1/4“ 17798 37 3/4“ 17798 37 3/8“ 17798 37 5/8“ 17798 37 5/16“ 17798 37 7/16“ 17798 37 9/16“ 17798 37 10 17798 37 11 17798 37 12 17798 37 13 17798 37 14 17798 37 17 17798 37 19 17798 39 05 17998 39 06 17998 40 17698 41 17698 42 17998 43 50 179

83 10 010 9383 10 015 9383 10 020 9383 10 030 9383 10 040 9383 20 010 9383 20 015 9383 20 020 9383 30 005 9383 30 010 9383 30 015 9383 30 020 9383 30 030 9384 11 200 9284 21 200 9285 01 250 10086 03 150 9586 03 180 9586 03 250 9586 03 300 9586 05 150 9586 05 180 9586 05 250 9586 07 250 16287 01 125 9787 01 150 9787 01 180 9787 01 250 9787 01 300 9787 01 400 9887 01 560 9887 02 180 9787 02 250 9787 02 300 9787 03 125 9787 03 180 9787 03 250 9787 03 300 9787 05 250 9787 05 300 9787 11 250 10187 19 250 10187 26 250 101/16387 41 250 10287 51 250 10388 01 180 10588 01 250 10588 01 300 10588 02 180 10588 02 250 10588 02 300 10588 03 180 10588 03 250 10588 05 180 10588 05 250 10588 05 300 10588 06 250 105/16288 07 250 105/16288 07 300 105/16289 01 200 10689 01 250 10689 03 250 10689 05 250 10690 01 125 10690 03 125 10690 20 185 10890 25 20 10890 25 40 10990 29 01 10890 29 02 10890 29 15 10890 29 40 10990 29 185 10890 42 250 10990 42 340 10990 49 340 10990 49 340 M 10990 55 280 11090 59 280 11090 61 16 11090 61 20 11090 70 220 11191 00 200 11191 11 190 11191 31 180 11291 51 160 11291 61 160 11291 71 160 11292 02 53 11392 02 54 113

INDEX ARTICLE NUMBER / PAGE

It is not permissible to copy the catalogue or parts of it in any way without our approval.

Subject to model modifications and technical changes.

Illustrations, dimensions and weights are just approxi-mate. No liability is assumed for misprints or errors.

Printed in the Federal Republic of Germany.

KNIPEX-Werk C. Gustav Putsch KG 2011

KNIPEX-Werk C. Gustav Putsch KG

Oberkamper Straße 13 42349 Wuppertal (Germany)

Tel.: +49 (0) 202-47 94-0 Fax: +49 (0) 202-47 74 94

[email protected] · www.knipex.de

L100 02167/01/06.11/40.000/EN

knipex general catalogue 2011 en web[1]

Documents