lab ccnp route eigrp (1)

Laboratrios EIGRP para CCNP Route

(VERSO 1.0)

NDICE EIGRP LABS

1. Configurao Bsica EIGRP

2. Configurar ip default-network

3. Sumarizao de Rotas com EIGRP

4. Load Balancing sobre Caminhos com Custos Iguais

5. Load Balancing sobre Caminhos com Custos Diferentes

6. Autenticao EIGRP

7. Configurando EIGRP STUB

8. Redistribuio EIGRP com RIPv2

9. Redistribuio EIGRP com OSPF

10. Configurando EIGRP com redistribuio de rotas

conectadas

INDICE EIGRP LABS GNS3

1. EIGRP-Basic

2. EIGRP IP Default

3. EIGRP Summarization

4. EIGRP Load Balancing Equal Cost

5. EIGRP Load Balancing Unequal Cost

6. EIGRP Authentication

7. Configuring EIGRP STUB

8. Redistribute EIGRP with RIPv2

9. Redistributing EIGRP with OSPF

10. Redistributing EIGRP with Connected

Obs.: Esses Lab acima estaro disponveis para download em

www.stato.blog.br. Cada Lab ter uma pasta com o nome acima, e dentro

desta pasta estar disponvel, so arquivos .net com a Topologia, onde um

estar em branco, que poder ser usado para treinar, e outro j resolvido. Alm

disso, as configuraes dos roteadores e imagens usadas nesse Lab tambm

estaro disponveis.

A imagem do roteador usada foi um Cisco 3725 que tambm estar disponvel

para download separadamente no site c3725-adventerprisek9-mz.124-

15.T5.bin

EIGRP

LAB 1 Configurao Bsica

R1

interface Ip Address Subnet Mask s0/0 1.1.1.1 255.0.0.0

f0/0 10.1.1.1 255.0.0.0

R2


f0/0 20.1.1.1 255.0.0.0

Tarefa 1 : Configurar EIGRP nos 2 roteadores como AS 100. Desabilitar Auto-Summary

Configurao R1 Configurao R2

R1# en

R1#conf t

R1#interface serial 0/0

R1#ip address 1.1.1.1 255.0.0.0

R1#no shut

R1#interface f0/0

R1#ip address 10.1.1.1 255.0.0.0

R1#no shut

R1#exit

R1#router eigrp 100

R1#network 1.0.0.0

R1#network 10.0.0.0

R1#no auto-sumamry

R1#exit

R1#copy run start

R2# en

R2#conf t


R2#ip address 1.1.1.2 255.0.0.0

R2#no shut

R2#interface f0/0

R2#ip address 20.1.1.1 255.0.0.0

R2#no shut

R2#exit

R2#router eigrp 100

R2#network 1.0.0.0

R2#network 20.0.0.0

R2#no auto-sumamry

R2#exit

R2#copy run start

Verificao

R1#show ip route

C 1.0.0.0/8 is directly connected, Serial0/0

D 20.0.0.0/8 [90/2195456] via 1.1.1.2, 00:43:52, Serial0/0

C 10.0.0.0/8 is directly connected, FastEthernet0/0

R1#show ip eigrp neighbors

IP-EIGRP neighbors for process 100

H Address Interface Hold Uptime SRTT RTO Q Seq

(sec) (ms) Cnt Num

0 1.1.1.2 Se0/0 13 00:11:20 75 450 0 5

LAB 2 Configurar ip default-network

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

R3


f0/0 30.1.1.1 255.0.0.0

Tarefa 1: Configurar EIGRP de acordo com o cenrio. Configure R1 (S0/0 , F0/0), R2

(S0/0,S0/1,F0/0) e EIGRP AS como 100 e R3 (S0/0) como AS 200. Do configure a rede 30.0.0.0

no processo EIGRP 100. R1 quer enviar pacotes para 30.0.0.0. Use o ip default-network como

realizar essa tarefa. Configure o ip default-network em R2. Desabilite Auto-Summary.

Configurao R1

R1# en

R1#conf t


R1#ip address 1.1.1.1 255.0.0.0

R1#no shut

Configurao R2

R2# en

R2#conf t


R2#ip address 1.1.1.2 255.0.0.0

R2#no shut

R1#interface f0/0

R1#ip address 10.1.1.1 255.0.0.0

R1#no shut

R1#exit

R1#router eigrp 100

R1#network 1.0.0.0

R1#network 10.0.0.0

R1#no auto-sumamry

R1#exit

R1#copy run start

Configurao R3

R3# en

R3#conf t


R3#ip address 2.2.2.2 255.0.0.0

R3#no shut

R3#interface f0/0

R3#ip address 30.1.1.1 255.0.0.0

R3#no shut

R3#exit

R3#router eigrp 100

R3#network 2.0.0.0

R3#no auto-sumamry

R3#exit

R3#copy run start

R2#interface f0/0

R2#ip address 20.1.1.1 255.0.0.0

R2#no shut

R2#interface s0/1 2.2.2.1 255.0.0.0

R2#exit

R1#router eigrp 100

R1#network 1.0.0.0

R2#network 2.0.0.0

R1#network 20.0.0.0

R1#no auto-sumamry

R1#exit

R2#ip route 30.0.0.0 255.0.0.0 2.2.2.2

R2#ip default-network 2.0.0.0

R1#copy run start

Verificao

R1#show ip route

Gateway of last resort is 1.1.1.2 to network 2.0.0.0


D* 2.0.0.0/8 [90/2681856] via 1.1.1.2, 00:11:47, Serial0/0

D 20.0.0.0/8 [90/2195456] via 1.1.1.2, 00:13:44, Serial0/0


Podemos ver que a rota da rede 2.0.0.0 com um D* na tabela de roteamento um candidata a

estabelecer um routa padro ( default-route) em R1 para alcanar 30.0.0.0

R1#ping 30.1.1.1

Resultado: 100% sucess

LAB 3 Sumarizao de Rotas com EIGRP

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

R3


f0/0 30.1.1.1 255.0.0.0

Loopback 1 172.16.0.1 255.255.255.0

Loopback 2 172.16.2.1 255.255.255.0

Loopback 3 172.16.3.1 255.255.255.0

Loopback 4 172.16.4.1 255.255.255.0

Loopback 5 172.16.5.1 255.255.255.0

Loopback 6 172.16.6.1 255.255.255.0

Loopback 7 172.16.7.1 255.255.255.0

Loopback 8 172.16.8.1 255.255.255.0

Tarefa 1: Configurar as loopbacks em R3.

Configurao R3 ( identica ao Lab anterior +

os itens abaixo )

R3# en

R3#conf t

R3#interface loopback 1

R3#ip address 172.16.0.1 255.255.255.0


R3#ip address 172.16.1.1













R3#exit

R3#irouter eigrp 100

R3#network 2.0.0.0

R3#network 30.0.0.0

R3#network 172.16.0.0 0.0.0.255

R3#network 172.16.1.0 0.0.0.255

R3#network 172.16.2.0 0.0.0.255

R3#network 172.16.3.0 0.0.0.255

R3#network 172.16.4.0 0.0.0.255

R3#network 172.16.5.0 0.0.0.255

R3#network 172.16.6.0 0.0.0.255

R3#network 172.16.7.0 0.0.0.255

R3#no auto-sumamry

R3#exit

R3#copy run start

Tarefa 2: Configure EIGRP on R1 e R2, conforme lab anterior. Configure uma rota sumarizada

para as rede 172.16 , mas somente o R1 deve ser avisado desta rota sumarizada.

Configurao R2

R2# en

R3#conf t


R3#ip summary-address eigrp 100 172.16.0.0

255.255.248.0

R3#exit

R3#copy run start

LAB 4 Load Balancing sobre Caminhos com Custos Iguais

R1


S0/1 2.2.2.1 255.0.0.0

f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.2 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

Tarefa 1: Configurar EIGRP com AS 100 conforme cenrio acima e verificar balanceamento de

carga utilizando o Traceroute R1.

Configurao R1

R1# en

R1#conf t


R1#ip address 1.1.1.1 255.0.0.0

R1#no shut


R1#ip address 2.2.2.1 255.0.0.0

R1#no shut

R1#interface f0/0

R1#ip address 10.1.1.1 255.0.0.0

R1#no shut

Configurao R2

R2# en

R2#conf t


R2#ip address 1.1.1.2 255.0.0.0

R2#no shut


R2#ip address 2.2.2.2 255.0.0.0

R2#no shut

R2#interface f0/0

R2#ip address 20.1.1.1 255.0.0.0

R2#no shut

R1#exit

R1#router eigrp 100

R1#network 1.0.0.0

R1#network 2.0.0.0

R1#network 10.0.0.0

R1#no auto-sumamry

R1#exit

R1#copy run start

R2#exit

R1#router eigrp 100

R1#network 1.0.0.0

R2#network 2.0.0.0

R1#network 20.0.0.0

R1#no auto-sumamry

R1#exit

R1#copy run start

Verificao

R1#show ip route



D 20.0.0.0/8 [90/2195456] via 2.2.2.2, 00:07:00, Serial0/1

[90/2195456] via 1.1.1.2, 00:07:00, Serial0/0


possivel verificar que existe duas rotas para a mesma rede.

Primeiro traceroute via 2.2.2.1:

R1#traceroute 20.1.1.1

Type escape sequence to abort.

Tracing the route to 20.1.1.1

1 2.2.2.2 28 msec

1.1.1.2 36 msec

2.2.2.2 48 msec

Segundo traceroute ir via 1.1.1.1:

R1#traceroute 20.1.1.1

Type escape sequence to abort.

Tracing the route to 20.1.1.1

1 1.1.1.2 48 msec

2.2.2.2 44 msec

1.1.1.2 60 msec

LAB 5 Load Balancing sobre Caminhos com Custos Diferentes

R1


S0/1 2.2.2.1 255.0.0.0

f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.2 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

Este laboratrio identico ao anterior em relao a estrutura, alterando-se apenas a forma

como as rotas sero distribuidas.

Tarefa 1: Configurar EIGRP com AS 100 conforme cenrio acima e fazer balenceamento com

custos desiguais usando o comando bandwidth na interface e verificar o balanceamento de

carga.

Configurao R1

R1# en

R1#conf t


R1#ip address 1.1.1.1 255.0.0.0

R1#no shut


R1#ip address 2.2.2.1 255.0.0.0

R1#no shut

Configurao R2

R2# en

R2#conf t


R2#ip address 1.1.1.2 255.0.0.0

R2#no shut


R2#ip address 2.2.2.2 255.0.0.0

R2#no shut

R1#interface f0/0

R1#ip address 10.1.1.1 255.0.0.0

R1#no shut

R1#exit

R1#router eigrp 100

R1#network 1.0.0.0

R1#network 2.0.0.0

R1#network 10.0.0.0

R1#no auto-sumamry

R1#exit

R1#copy run start

R2#interface f0/0

R2#ip address 20.1.1.1 255.0.0.0

R2#no shut

R2#exit

R1#router eigrp 100

R1#network 1.0.0.0

R2#network 2.0.0.0

R1#network 20.0.0.0

R1#no auto-sumamry

R1#variance 2

R1#exit


R2#bandwidth 800

R1#copy run start

Verificao:

Poderemos verificar , que a mtrica das rotas do Roteador R2 para a rede 10.0.0.0/8 so

diferentes . A rota atravs do 2.2.2.1 menor que a pelo 1.1.1.1, onde neste link diminuimos a

banda atravs do comando bandwidth. Neste caso tambm , temos apenas um sucessor (

diferente do exercicio anterior que possuiamos dois Sucessors ).

R2#show ip eigrp topology

P 1.0.0.0/8, 1 successors, FD is 3712000

via Connected, Serial0/0

via 2.2.2.1 (2681856/2169856), Serial0/1


via Connected, Serial0/1


via 2.2.2.1 (2195456/281600), Serial0/1

via 1.1.1.1 (3737600/281600), Serial0/0


via Connected, FastEthernet0/0

R2#show ip route




D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:02:34, Serial0/1

[90/3737600] via 1.1.1.1, 00:02:34, Serial0/0

LAB 6 Autenticao EIGRP

R1


f0/0 10.1.1.1 255.0.0.0

R2


f0/0 20.1.1.1 255.0.0.0

Tarefa 1: Configurar autenticao MD5 entre os links. User cisco123 como string e key-id 1.

Configurao R1

R1# en

R1#conf t


R1#ip address 1.1.1.1 255.0.0.0

R1#ip authentication mode eigrp 100 md5

R1#ip authentication key-chain eigrp 100

chaveiro1

R1#no shut


R1#ip address 2.2.2.1 255.0.0.0

R1#no shut

R1#interface f0/0

R1#ip address 10.1.1.1 255.0.0.0

R1#no shut

Configurao R2

R2# en

R2#conf t


R2#ip address 1.1.1.2 255.0.0.0

R2#ip authentication mode eigrp 100 md5

R2#ip authentication key-chain eigrp 100

chaveiro2

R2#no shut


R2#ip address 2.2.2.2 255.0.0.0

R2#no shut

R2#interface f0/0

R2#ip address 20.1.1.1 255.0.0.0

R2#no shut

R1#exit

R1#router eigrp 100

R1#network 1.0.0.0

R1#network 10.0.0.0

R1#no auto-sumamry

R1#key chain chaveiro1

R1#key 1

R1#key-string cisco123

R1#exit

R1#copy run start

R2#exit

R2#router eigrp 100

R2#network 1.0.0.0

R2#network 20.0.0.0

R2#no auto-sumamry


R2#key 1


R2#exit

R2#copy run start

Verificao:



H Address Interface Hold Uptime SRTT RTO Q Seq

(sec) (ms) Cnt Num

0 1.1.1.2 Se0/0 13 00:08:13 94 564 0 8

Verificao da autenticao usando debug.

R1#debug eigrp packets

*Mar 1 00:20:43.555: EIGRP: Sending HELLO on Serial0/0

*Mar 1 00:20:43.555: AS 100, Flags 0x0, Seq 0/0 idbQ 0/0 iidbQ un/rely 0/0

*Mar 1 00:20:44.655: EIGRP: Sending HELLO on FastEthernet0/0


*Mar 1 00:20:46.915: EIGRP: received packet with MD5 authentication, key id = 1

*Mar 1 00:20:46.915: EIGRP: Received HELLO on Serial0/0 nbr 1.1.1.2

Tarefa 2 : Alterar string para cisco321, e veriricar mensagens de erros.

Podemos alterar as configuraes em R2, para causar um problema de autenticao, e

verificar os pacotes logados.

Configurao R2

R1# en

R1#conf t


R2#key 1


Verificao:



R1#debug eigrp packets

EIGRP: Sending HELLO on Serial0/0


*Mar 1 00:32:23.223: EIGRP: Sending HELLO on FastEthernet0/0


*Mar 1 00:32:26.875: EIGRP: pkt key id = 1, authentication mismatch

*Mar 1 00:32:26.875: EIGRP: Serial0/0: ignored packet from 1.1.1.2, opcode = 5 (invalid

authentication)

LAB 7 Configurando EIGRP STUB

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 3.3.3.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

R3

interface Ip Address Subnet Mask

s0/0 3.3.3.2 255.0.0.0

f0/0 30.1.1.1 255.0.0.0

Loopback 0 172.16.0.1 255.255.255.0

Loopback 1 172.16.2.1 255.255.255.0

Loopback 2 172.16.3.1 255.255.255.0

Loopback 3 172.16.4.1 255.255.255.0

Tarefa 1: Configure as interfaces conforme ilustrao acima ( e exerccios anteriores ), sobre

dominio EIGRP com AS 100. Desabilite auto-sumary e somente rotas sumarizadas devem ser

enviadas ( advertised ) para os routers R1 e R2.

As configuraes de interface podem ser vistas em Labs anteriores, abaixo ser mostrado

somente a configurao do EIGRP.

Configurao R1

R1# router eigrp 100

R1# network 2.0.0.0

R1# network 10.0.0.0

R1# no auto-summary

Configurao R2


R2# network 2.0.0.0

R2# network 3.0.0.0


R2# no auto-summary

Configurao R3


R3# network 3.0.0.0


R3# network 172.168.0.0

R3#no auto-summary

R3#intercafe serial 0/0

R3#ip summary-address eigrp 100 172.16.0.0

255.255.252.0

Verificao sem configurar stub no R2:

R2#show ip route




172.168.0.0/22 is subnetted, 1 subnets

D 172.168.0.0 [90/2297856] via 3.3.3.2, 00:26:17, Serial0/1

D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:34:19, Serial0/0

D 30.0.0.0/8 [90/2195456] via 3.3.3.2, 00:27:40, Serial0/1

A sada mostra rotas diretamente conectadas, rotas sumarizadas e rotas EIGRP.

Tarefa 2: Configure Stub EIGRP em R3, prevenindo R3 de enviar qualquer rota para R2, mas R2

recebe rotas de R1.

Configurao R3


R3#eigrp stub receive-only

Verificao em R2:

R2#show ip route




D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:43:04, Serial0/0

A sada exibe somente a rede 10.0.0.0 ( rota eigrp ) vinda de R1, mas no mostra rotas Eigrp de

R3.

Tarefa 3: Configure Stub Eigrp no R3, permitindo que ele envie somento rotas conectadas

para R2, mas R2 continua recebendo rotas normalmente de R1.

Configurao R3


R3#eigrp stub connected

Verificao:

R2#show ip route





D 172.168.0.0 [90/2297856] via 3.3.3.2, 00:00:07, Serial0/1

D 172.168.1.0 [90/2297856] via 3.3.3.2, 00:00:07, Serial0/1

D 172.168.2.0 [90/2297856] via 3.3.3.2, 00:00:07, Serial0/1

D 172.168.3.0 [90/2297856] via 3.3.3.2, 00:00:07, Serial0/1

D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:47:28, Serial0/0

D 30.0.0.0/8 [90/2195456] via 3.3.3.2, 00:00:07, Serial0/1

A sada exibe somente rotas eigrp conectas de R3 para R2, mas recebe todas rotas de R1.

Tarefa 4: Configure Stub Eigrp em R3, permitindo somente rotas sumarizadas de R3 para R2,

mas R2 continua recebendo todas as rotas normalmente de R1.

Configurao R3


R3#eigrp stub summary

Verificao:

R2#show ip route





D 172.168.0.0 [90/2297856] via 3.3.3.2, 00:00:05, Serial0/1

D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:51:11, Serial0/0

A sada exibe somente rotas sumarizadas de R3, e tambm todas as rotas de R1.

Tarefa 5: Configure Stub Eigrp em R3, permitindo rotas sumarizadas e rotas conectadas de R3

para R2, mas R2 continua recebendo todas as rotas normalmente de R1.

Configurao R3


R3#eigrp stub

Verificao:

R2#show ip route





D 172.168.0.0 [90/2297856] via 3.3.3.2, 00:00:00, Serial0/1

D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 00:53:44, Serial0/0

D 30.0.0.0/8 [90/2195456] via 3.3.3.2, 00:00:00, Serial0/1

A sada exibe tanto rotas conectadas como rotas sumarizadas de R3, o comando eigrp stub,

por padro exibir rotas conectas e sumarizadas, como se fosse o prprio comando eigrp stub

connected summary.

Tarefa 6 : Neste Lab, usado a mesma topologia como base. Desta forma todas configuraes

anteriores so validas para esse Lab. As interfaces devem estar configuradas conforme

exercicio anterior, e a configurao stub dever ser padro, ou seja, conectadas e rotas

sumarizadas.

Configurar EIGRP no AS 100 para R1,R2 e R3. Configurar somente a interface f0/0 do R4 no

EIGRP 100. Configurar uma rota estatica em R3 para alcanar a rede 40.0.0.0 via 30.1.1.1.

Redistribuir rotas estticas em EIGRP AS 100.

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 3.3.3.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

R3


f0/0 30.1.1.1 255.0.0.0

Loopback 0 172.16.0.1 255.255.255.0

Loopback 1 172.16.2.1 255.255.255.0

Loopback 2 172.16.3.1 255.255.255.0

Loopback 3 172.16.4.1 255.255.255.0

R4

interface Ip Address Subnet Mask f0/0 30.1.1.2 255.0.0.0

f0/1 40.1.1.1 255.0.0.0

Configurao R4

R4#en R4#conf t

R4#interface f0/0

R4#ip address 30.1.1.2 255.0.0.0

R4#interface f0/1

R4#ip address 40.1.1.1 255.0.0.0

R4#exit


R4#router eigrp 100

R4#network 30.0.0.0

R4#exit

R4#write

Configurao R3


R3# redistribute static metric 10 10 10 10 10

R3# eigrp stub static

No caso do R3 foi usado o comando redistribute static metric 10 10 10 10 10. O valores aps

metric, so respectivamente: bandwidth ( em kbps), delay ( em milisegundos ), reliability (

mximo = 255), load (minimo = 1 ) e MTU ( em bytes).

Verificao:

R2#show ip route




D EX 40.0.0.0/8 [170/256514560] via 3.3.3.2, 00:11:55, Serial0/1

D 10.0.0.0/8 [90/2195456] via 2.2.2.1, 03:09:58, Serial0/0

A sada exibe somente rotas diretamente conectas de R1 e R2, rotas EIGRP de R1, e rotas

redistribuidas de R3, mas bloqueia rotas conectadas e sumarizadas de R3. A sada mostra

tambm a rota redistribuida como external EIGRP ( D EX) com AD ( Distncia Administrativa)

de 170.

LAB 8 Redistribuio EIGRP com RIPv2

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

Loopback0 40.1.1.1 255.0.0.0

R3


f0/0 30.1.1.1 255.0.0.0

Tarefa 1: Configurar EIGRP AS 100 em R1 ( s0/0 e f0/0). R2 (s0/0 e f0/0) e RIPv2 em R2 (S0/1 e

Loopback0) e R3 (s0/0 e F0/0) como o cenrio indica. Mutualmente redistriir ambos protocolos

em R2, ou seja, tanto EIGRP ser redistribuido para o RIP em R3, como RIP ser redistribuido

para R1.

As tarefas de configurao de endereamento IP segue o padro visto em exerccios

anteriores.

Configurao R1


R1# network 1.0.0.0

Configurao R2


R2# network 1.0.0.0


R1# no auto-summary


R2# no auto-summary

R2# redistribuit rip metric 10 10 10 10 10

R2# router rip

R2# version 2

R2# network 2.0.0.0


R2# no auto-summary

R2# redistribute eigrp 100 metric 15

Configurao R3

R3# router rip

R3#version 2

R3# network 2.0.0.0


R3#no auto-summary

Verificao:

R1#show ip route


D EX 2.0.0.0/8 [170/256514560] via 1.1.1.2, 00:03:29, Serial0/0

D 20.0.0.0/8 [90/2195456] via 1.1.1.2, 00:03:57, Serial0/0

D EX 40.0.0.0/8 [170/256514560] via 1.1.1.2, 00:03:19, Serial0/0


D EX 30.0.0.0/8 [170/256514560] via 1.1.1.2, 00:01:58, Serial0/0

R2#show ip route




C 40.0.0.0/8 is directly connected, Loopback0

D 10.0.0.0/8 [90/2195456] via 1.1.1.1, 00:14:23, Serial0/0

R 30.0.0.0/8 [120/1] via 2.2.2.2, 00:00:04, Serial0/1

R3#show ip route

R 1.0.0.0/8 [120/15] via 2.2.2.1, 00:00:06, Serial0/0


R 20.0.0.0/8 [120/15] via 2.2.2.1, 00:00:06, Serial0/0

R 40.0.0.0/8 [120/1] via 2.2.2.1, 00:00:06, Serial0/0

R 10.0.0.0/8 [120/15] via 2.2.2.1, 00:00:06, Serial0/0


A sada exibe routas RIP que foram informadas para R1 via EIGRP AS 100 como D EX rotas.

Rotas EIGRP so enviadas como R rotas para o RIP.

LAB 9 Redistribuio EIGRP com OSPF

R1


f0/0 10.1.1.1 255.0.0.0

R2


S0/1 2.2.2.1 255.0.0.0

f0/0 20.1.1.1 255.0.0.0

R3


f0/0 30.1.1.1 255.0.0.0

Tarefa 1: Configurar EIGRP AS 100 no R1 (s0/0,f0/0), R2 (s0/0) e OSPF area 0 em R2 (s0/1,

f0/0) e R3 (s0/0) e OSPF area 1 em R3 (f0/0) como exibido no cenrio. Redistribuir

mutuamente ambos protocolos.


anteriores.

Configurao R1


R1# network 1.0.0.0


R1# no auto-summary

Configurao R3

R3# router ospf

R3# network 2.2.2.2 0.0.0.0 area 0

R3# network 30.0.0.0 0.255.255.0 area 1

Configurao R2


R2# network 1.0.0.0

R2# no auto-summary

R2# redistribuit ospf 1 metric 10 10 10 10 10

R2# router ospf

R2# network 2.1.1.1 0.0.0.0 area 0

R2# network 20.0.0.0 0.255.255.255 area 0

R2# redistribute eigrp 100 metric 10 subnets

Verificao:

R1#show ip route


D EX 2.0.0.0/8 [170/256514560] via 1.1.1.2, 00:02:25, Serial0/0

D EX 20.0.0.0/8 [170/256514560] via 1.1.1.2, 00:02:04, Serial0/0


D EX 30.0.0.0/8 [170/256514560] via 1.1.1.2, 00:00:10, Serial0/0

R2#show ip route




D 10.0.0.0/8 [90/2195456] via 1.1.1.1, 00:03:25, Serial0/0

O IA 30.0.0.0/8 [110/74] via 2.2.2.2, 00:00:16, Serial0/1

R3#show ip route

O E2 1.0.0.0/8 [110/10] via 2.2.2.1, 00:00:41, Serial0/0


O 20.0.0.0/8 [110/74] via 2.2.2.1, 00:00:41, Serial0/0

O E2 10.0.0.0/8 [110/10] via 2.2.2.1, 00:00:41, Serial0/0


LAB 10 Configurando EIGRP com redistribuio de rotas

conectadas

R1


f0/0 10.1.1.1 255.0.0.0

R2


f0/0 20.1.1.1 255.0.0.0

Tarefa 1: Configurar EIGRP AS 100 and no configurar ( advertise ) redes 10.0.0.0 e 20.0.0.0,

ento redistribuir tais redes dentro do EIGRP.


anteriores.

Configurao R1

R1#router eigrp 100

R1#network 1.0.0.0

R1#no auto-sumamry

R1#redistribute connected metric 10 10 10

10 10

Configurao R2

R2#router eigrp 100

R2#network 1.0.0.0

R2#no auto-sumamry

R2#redistribute connected metric 10 10 10

10 10

Verificao:

R1#show ip route


D EX 20.0.0.0/8 [170/256514560] via 1.1.1.2, 00:02:13, Serial0/0


R2#show ip route



D EX 10.0.0.0/8 [170/256514560] via 1.1.1.1, 00:03:27, Serial0/0

lab ccnp route eigrp (1)

Documents

configurao r1 r1

eigrp ip default

r1 s00

r2 s00

interface f00 r1

shut r1

redistribuio eigrp

exit r1