lab_0_v5_1 - installing esxi - version_20130326

VMware vSphere 5.1: Install, Configure, Manage

Lab Addendum

Lab 0: Installing ESXi

NETLAB+ Supplemental Lab

Document Version: 2013-03-26

This lab is NOT part of the VMware vSphere 5.1 Install, Configure, Manage course; however, it contains configuration tasks that are necessary in order to complete the lab series, using a NETLAB+ system.

Please note that the sequence of the lab addenda differs slightly from the sequence of the VMware vSphere Install, Configure, Manage 5.1 labs. This is necessary in order to provide compatibility with NETLAB+. The labs should be performed in the order of the lab addenda.

Copyright © Network Development Group, Inc. www.netdevgroup.com NETLAB Academy Edition, NETLAB Professional Edition, and NETLAB+ are registered trademarks of Network Development Group, Inc. VMware is a registered trademark of VMware, Inc. Cisco, IOS, Cisco IOS, Networking Academy, CCNA, and CCNP are registered trademarks of Cisco Systems, Inc.

Lab 0: Installing ESXi www.netdevgroup.com

4/10/2013 of 8

1 Introduction ................................................................................................................ 3

2 Objective: Install ESXi on a local volume .................................................................... 3

3 Pod Topology .............................................................................................................. 4

Task 1 Install ESXi software ............................................................................................. 5

Task 2 Configure network settings .................................................................................. 7


4/10/2013 of 8

1 Introduction

This lab provides detailed guidance on installing ESXi and the configuration of network settings.

This lab is NOT part of the VMware vSphere 5.1 Install, Configure, Manage course; however, it contains configuration tasks that are necessary in order to complete the lab series, using a NETLAB+ system

2 Objective: Install ESXi on a local volume

In this lab, you will be using the esxi-2 machine to complete your objectives. You will be performing the following tasks:

1. Install the ESXi v5.1 software. 2. Configure the network settings.

The esxi-1 host is installed and preconfigured. This lab is designed to be used with the esxi-2 host.


4/10/2013 of 8

3 Pod Topology


4/10/2013 of 8

Task 1 Install ESXi software

In this task, you install ESXi software on your host. The ESXi software is on an installation DVD, already inserted into the machine.

1. Upon lab startup, the esxi-2 host is booted with the installation DVD. Click on the esxi-2 host in the topology to have access to the console.

2. You will be greeted with the Installation screen below.

3. Press Enter to continue.

If you are using a Mac computer to access the labs, you may have to change a system preference. Navigate to System Preferences > Keyboard Shortcuts > Expose and Spaces and uncheck the checkbox next to the F11 key.

4. You will be prompted with the User Agreement. Press F11 (Accept and

Continue). 5. On the Select a Disk screen, choose the first local virtual disk listed. Press Enter

to continue.


4/10/2013 of 8

6. Choose your keyboard layout, the default is US Default. Press Enter. 7. Enter and confirm the root password as vmware123 and press Enter. 8. You may see a warning that Hardware Virtualization is not a CPU Feature. Ignore

this warning by pressing Enter to continue.

9. Confirm the installation by pressing F11. 10. Installation can take 1-5 minutes depending on server hardware. 11. When the Installation Complete window appears, press Enter to reboot the

machine.

It is not necessary to remove the installation disk within this virtual environment.


4/10/2013 of 8

Task 2 Configure network settings

In this task, you will configure the esxi-2 host network configuration.

1. When the esxi-2 host is booted, you will be presented with the console screen. 2. To setup the host, press F2 to begin.

If the console screen is black, you will need to hit F2 twice to start the installation. The first keystroke wakes the console screen.

3. You will be prompted to login. The default username is root and the password is

vmware123. Press Enter to continue. 4. From the console, choose Configure Management Network and press Enter.

5. In the Configure Management Network window, choose IPv6 Configuration and press Enter.

6. Uncheck the checkbox next to Enable IPv6 (restart required) and press Enter. 7. In the Configure Management Network window, choose IP Configuration and

press Enter. 8. In the IP Configuration window, choose Set static IP address and network

configuration, press Spacebar to select and enter the following using the arrow keys to move between sections:


4/10/2013 of 8

9. Press Enter to confirm changes and return to the Configure Management Network window.

10. In the Configure Management Network window, choose DNS Configuration and press Enter.

11. Make sure “Use the following DNS server addresses and hostname” is selected and enter the following:

12. Press Enter to confirm changes and return to the Configure Management Network window.

13. Press Esc to return to the main console. 14. You will be prompted to “Apply changes and restart management network”,

press Y to confirm changes. Your host will restart. 15. You will return to the main console. Press Esc to log out. 16. You can now close your esxi-2 console window.

lab_0_v5_1 - installing esxi - version_20130326

Documents