2017-12-29

RG185Y X S-01

TFT-LCD SUPPLIER

Web:www.odmlcd.com

TLE:0086-0755-23100652

RONGEN TECHNOLOGY CO.,LIMITED

CUSTOMER :

MODEL NO.:

ISSUED DATE:

VERSION: Ver. 01

■Preliminary Specification

□Final Product Specification

Customer :

Approved by Notes

RONGEN Confirmed:

Prepared by Checked by Approved by

TLE:0086-0755-23100652

RONGEN TECHNOLOGY CO.,LIMITEDTLE:0086-0755-23100652

RONGEN TECHNOLOGY CO.,LIMITEDTLE:0086-0755-23100652

RONGEN TECHNOLOGY CO.,LIMITED

LCD MODULE

SPECIFICATION

Record of Revisions

Rev. Date Sub-Model Description of change

A00 2017-12 -29 N/A

TFT-LCD SUPPLIER

Web:www.odmlcd.com

General Description

This specification applies to the color 18.5” TFT-LCD module

is a color active matrix liquid crystal display(LCD) incorporating amorphous silicon

TFT. This model is composed of a TFT-LCD panel, driver ICs, PWB. Graphics and texts can be

displayed on a 1366 x RGB x768 dot panel with about 16.7M colors(R/G/B 6 bits + Hi FRC data in

each color) by using LVDS(Low Voltage Differential Signaling) to interface,+5V of DC supply

voltage.

Features

High contrast ratio, high aperture structure

High speed response

FHD (1366 x 768 pixels) resolution

White LED Edge slim Backlight (1-side)

DE (Data Enable) only mode

LVDS (Low Voltage Differential Signaling) interface (2pixel/clock)

RoHS, Halogen Free

It is recommended to support in system level )

Applications

Workstation &desktop monitors

Display terminals for AV application products

Monitors for industrial machine

* If the module is used to other applications besides the above, please contact SEC

in advance.

General Information

Parameter Specifications Unit

Active area 409.8 (H) × 230.4(V) mm

Pixel Format 1366 (H) × 768 (V) （1pixel = R + G + B

dot） pixel

Pixel configuration R,G, B vertical stripe

Display mode Normally White

Luminance of white 220(TYP) Cd/㎡

Mechanical Information

Item Min Typ Max Unit Note

Module size Horizontal(H) 430.1 430.4 430.7 mm

Vertical(V) 254.5 254.8 255.1 mm

Depth(D) 10.5 10.8 11.1 mm

1.Absolute Maximum Ratings

This

TFT-LCD SUPPLIER

Web:www.odmlcd.com

2.Optical Characteristics

Ta = 25°C, Vcc = +12V, VINV = +24V

TFT-LCD SUPPLIER

Web:www.odmlcd.com

Parameter Symbol Condition Min. Typ. Max. Unit Remark

Viewing angle

range

Horizontal θ 21+θ 22 CR>10

160 170 - Deg.

Vertical θ 11+θ 12 150 160 - Deg.

Contrast ratio CR 700 1000 - -

Response time T g θ =0 deg. - 5 8 ms

Transmittance T 5.4 6.4 %

Chromaticity of white x

TYP-0.03

0.313

TYP+0.03

-

y 0.329 -

Chromaticity of red x 0.638 -

y 0.352 -

Chromaticity of green x 0.314 -

y 0.639 -

Chromaticity of blue x 0.158 -

y 0.060 -

Luminance of white YL 220 250 cd/m2

Luminance uniformity δW 75% - -- -

TFT-LCD SUPPLIER

Web:www.odmlcd.com

TFT-LCD SUPPLIER

Web:www.odmlcd.com

4.Electrical Characteristics

4.1 Absolute Maximum Rating

4.2 Control Circuit Driving

TFT-LCD SUPPLIER

Web:www.odmlcd.com

TFT-LCD SUPPLIER

Web:www.odmlcd.com

5 .1 Back Light Unit

Led Light Bar characteristics

Parameter Symbol

Value

Unit Note

Min. Typ. Max.

Light Bar Input Voltage VLED -- 31 -- VDC IL=240mA

Light Bar Input Current ILED 240 mADC

(Duty 100%)

Per string

Power Consumption PLED -- 7.44 -- W

LED Life Time LBL 30000 Hrs Note (1)

Note (1). The lifetime is defined as the time which luminance of the LED decays to 50% compared to the initial

value, Operating condition: Continuous operating at Ta = 25±2℃, IL =240mA

5.2 . LED LIGHT BAR Electrical Circuit

LED light bar circuit is(4)Parallel (10)Series

TFT-LCD SUPPLIER

Web:www.odmlcd.com

5.3 Backlight UNIT Connector Definition

Backlight Input connector model: Cl1406M1HRE-NH(CviLux)

+ + - ---

5.4 Timing characteristics of input signals

TFT-LCD SUPPLIER

Web:www.odmlcd.com

6. INPINPUT TERMINAL PIN ASSIGNMENT

6.1 TFT LCD Open Cell

TFT-LCD SUPPLIER

Web:www.odmlcd.com

TFT-LCD SUPPLIER

Web:www.odmlcd.com

6.2 Block Diagram (Open-Cell)

TFT-LCD SUPPLIER

Web:www.odmlcd.com

6.3 LVDS Interface

6.4 Color Data Input Assignment

TFT-LCD SUPPLIER

Web:www.odmlcd.com

7. Precautionsa) Because the Open-Cell is weak to static electricity, please do not touch the terminal with bare hands.

TFT-LCD SUPPLIER

Web:www.odmlcd.com

b) Since the front polarizer is easily damaged, pay attention not to scratch it.

c) Since long contact with drops of water may cause discoloration or spots, please wipe off them as soon as put

on the screen.

d) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

e) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Handle with

care.

f) Precautions of peeling off the protection film:

- Be sure to peel off slowly (recommended more than 7sec) and constant speed.

- Peeling direction shown in Fig. 5.

- Be sure to ground person with adequate methods such as the anti-static wrist band.

- Be sure to ground S-PWBs while peeling off the protection film.

- Ionized air should be blown to the surface while peeling off.

- The protection film must not touch drivers and S-PWBs.

- If adhesive may remain on the polarizer after the protection film peeled off, please remove with

isopropyl-alcohol.

Fig.5 Direction of peeling off

g) Since the Open-Cell consists of TFT and electronic circuits with CMOS-ICs, which are very weak to electrostatic

discharge, persons who are handling a Open-Cell should be grounded through adequate methods such as an anti-static

wrist band. Connector pins should not be touched directly with bare hands.

h) Avoiding COF damage, do not bend PWB to display side when handling the open cell, recommend coating silicon or

tuffy on front and back side of COF.

･Reference: Process control standard of CPL.

item Management standard value and performance standard

1 Anti-static mat(shelf) 1 to 50 [Mega ohm]

2 Anti-static mat(floor, desk) 1 to 100 [Mega ohm]

3 Ionizer Attenuate from ±1000V to ±100V within two seconds.

4 Anti-static wrist band 0.8 to 10 [Mega ohm]

5 Anti-static wrist band entry and

ground resistance

Below 1000 [ohm]

6 Temperature 22 to 26 [℃]

7 Humidity 60 to 70 [%]

i) Since the Open-Cell has some PWBs, please take care to keep them off any stress or pressure when handling or installing

the Open-Cell, otherwise some of electronic parts on them may be damaged.

j) Be sure to turn off the power supply when inserting or disconnecting the cable.

k) Be sure to design the module and cabinet so that the Open-Cell can be installed without any extra stress such as warp

or twist.

l) When handling and assembling Open-Cells into module and cabinets, please be noted that long-term storage in theenvironment of oxidization or deoxidization gas and the use of materials such as reagent, solvent, adhesive, resin, etc.

which generate these gasses, may cause corrosion and discoloration of the Open-Cell.

m) Applying too much force and stress to PWBs and drivers may cause a malfunction electrically and mechanically.

TFT-LCD SUPPLIER

Web:www.odmlcd.com

n) The Open-Cell has high frequency circuits. Sufficient suppression to EMI should be done by system manufactures.

o) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.

p) The chemical compound, which causes the destruction of ozone layer, is not being used.

q) This Open-Cell module is corresponded to ROHS.

r) When any question or issue occurs, it shall be solved by mutual discussion.

9.Packing form

顶卡 2PCS/SET

产品 12PCS/箱

格卡2 2PCS/箱

珍珠棉垫 3PCS/箱

外箱

格卡1 7PCS/箱

10. Carton storage condition

a) Temperature: 0°C to 40°C

b) Humidity: 95%RH or less

Reference condition: 20°C to 35°C, 85%RH or less (summer)

一箱装12PCS产品

TFT-LCD SUPPLIER

Web:www.odmlcd.com

: 5°C to 15°C, 85%RH or less (winter)

The total storage time (40°C, 95%RH): 240H or less

c) Sunlight:

Be sure to shelter a product from the direct sunlight.

d) Atmosphere:

Do not store in a place where exists the risk of corrosive gas (such as acid and alkali) or volatile solvents.

e) Prevent condensation:

Be sure to put cartons on a palette or base, don’t put it on the floor, and store them keeping off the wall. Please take

care of ventilation in storehouse and around cartons, and control temperature not to change abruptly beyond the natural

environment.

f) Storage life: 1 year

11. Reliability test item

Reliability test item:

No. Test item Condition

1 High temperature storage test Ta=60°C 240h

2 Low temperature storage test Ta=-25°C 240h

3 High temperature and high humidity

operation test

Ta=40°C ; 95%RH

(No condensation)

240h

4 High temperature operation test Ta=50°C 240h

5 Low temperature operation test Ta=0°C 240h

Above tests are executed under the LED module conditions.

TFT-LCD SUPPLIER

Web:www.odmlcd.com

12.Others

工 艺

审 核

设 计

标记

处数

日 期

标准化

更改

单号

批 准

分 区

签 名

规格

/型

号

第张

质量

版本

标记

A00

共 张

数量

比例

更 改

模组 外

形图

Electrical/Optical Specifications:

39

45.5

--

220

Chromaticit y coordinate

Ta=25°C

MAX.

UNIT mA

V(rms)

TYP.

24042.2

MIN.

f

=60mA

2

I f

RATIN

GS

cd/m %

20°

C to

+50°

C

30

°C t

o +60°

C

250

Topr

Tsty

75

SYMBOL

W

V IFor

ward

Curre

nt

For

ward

Volta

ge

I

Opera

ting

Tempe

ratu

re

Luminous Intensity

Lumin

ous

Unif

ormi

ty

Power

Dis

sipa

tion

P

SYMBOL

f d

E ach Lamp

CONDITIONS

If= 240 mA

If=60

mA/LED

ITEM

0.2

70

0.280

X Y0.3

00

0.3

10

0.3

30

0.3

40

10.1

--

--

--

--

5.. 视图

采用第三角法

4.. :为重要

尺寸

,(..) :为参考尺寸

1.. 未

按比例印图

2.. 修

改标记

3.. 制图单

位:mm; 未标示

公差±0.3

NOTES:

6.. 拔模角

度 1.5°

n

★

﹕7.. 测试仪

器(BM7)测试误

差亮

度±5%,色度±0.005

9. 3

10.9

v

Test

Poi

nt

1 4 7

2 5 8

3 6 9

4-M3

料号

13.01.DMW0185LL18-A

★★

★★

★★

★★

★★

★★

CS1014

DPC

S1014

DP34

.02.

1450

009

DMW0

185L

L18-A

conn

ect :

Cl1

406M

1HR

E-N

H(C

viLu

x)

- Pin1

- Pin2

+ Pin3

+ Pin4

- Pin5

- Pin6

TFT-LCD SUPPLIER

Web:www.odmlcd.com