le fonctionnement du produit et les risques … · bird guard lays on top of casting. td17 series...
TRANSCRIPT
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
1INSTALLATION INSTRUCTIONS
F-4260_090314
Luminaire for Parking GaragesTEKDEK™ LED
IMPORTANT SAFEGUARDSWhen using electrical equipment, basic safety precautions should
always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET
LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.
DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT
CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE. SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS
INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONSSAFETY RECOMMENDATION
TD17 SERIES
SAFETY RECOMMENDATIONA 1/16" diameter aircraft cable with end-loop (not included) is recommended for attaching the �xture structural to the upper structural.
1/16" DIA. AIRCRAFT CABLE(SUPPLIED BY OTHERS)
AIRCRAFT CABLE ATTACHTO UPPER STRUCTURAL
SCREW (SUPPLIED BY OTHERS)
A 1/16" diameter cable with end-loop (not included) is recommended for attaching the fi xture structural to the upper structural
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
2INSTALLATION INSTRUCTIONS
F-4260_090314
1: Remove tertiary lens (if provided) by unscrewing (4) captive screws.
2: Remove heatsinking/LED base by unscrewing (4) captive screws. These will be the inner most screws.
3: Disconnect the quick connector wires from the LED board and the driver.
4: Make electrical connection to J-box (for sizes, see next page). Circuit wire connection must be in J-box. Install housing to surface using (4) 5/16" diameter mounting holes.
5: Re-assemble by reversing the removal procedure.
DRIVERQUICK CONNECT HEATSINK/LED BASE
CAPTIVE SCREWS (4) FOR REMOVING HEATSINK
CAPTIVE SCREWS (4)
TERTIARY LENS (IF PROVIDED)
HOUSING
HOUSING TOP VIEW
5/16” MOUNTING HOLES (4)
DIRECT TO SURFACE INSTALLATION
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
2INSTALLATION INSTRUCTIONS
F-4258_010714
QUICK MOUNT KIT INSTALLATION
1: Quick mount plate fastens to a secure J-box. Screws by others.
2: Align hanger bracket with center slot on top of fi xture as shown at right. Fixture can then hang from bracket while electrical connections are made.
3: After excess wires are in J-box (see sizes below), push the fi xture up to the mounting plate. Locking hooks should slide through slots. Twist fi xture until a “click” is felt or heard. Fixture is now in place.
LOCKING HOOKS
HANGER BRACKET QUICK MOUNT PLATE
1.
2. ALIGN HANGER BRACKETWITH CENTER SLOT
LOCKING HOOK SLOTS
3.
USED WITH THE FOLLOWING JUNCTION BOX SIZES:4" ROUND 4" SQUARE3-1/2" OCTAGON
3.37
3.37
2.50
2.50
4.773.50
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
2INSTALLATION INSTRUCTIONS
F-4557_041013
BIRD GUARD INSTALLATION
1. Fasten tab through slots as shown above.
No tools required. Must install before fi xture is mounted.
2. Bird Guard lays inside of casting.
DIRECT TO SURFACE & QUICK MOUNT
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
2INSTALLATION INSTRUCTIONS
F-4259_041013
PENDANT MOUNT INSTALLATION
1: Attach 3/4" threaded conduit to housing (provided by others).
2: Make electrical connections in conduit body (supplied by others).
CONDUIT BODY AND CONDUIT (BY OTHERS)
HOUSING TAPPED FOR 3/4” NPS THREAD
MUST USE SEALANT OR SEALING LOCKNUT
SWIVEL MOUNT NOT RECOMMENDED (Kenall does not supply counterbalance system)
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
2INSTALLATION INSTRUCTIONS
F-4257_041013
TRUNNION KIT INSTALLATION
1: Attach housing plate to housing. Align notch. Use (4) fl at head screws (provided).
2: Assemble trunninon kits as shown using (4) ¼ -20 × .500" screws and nuts (provided).
3: Attach trunnion brackets to housing plate with (4) 10-32 × .375" hex head screws (provided).
4: Make electrical connections in conduit body (supplied by others).
NOTE: Top of bracket to top of the fi xture measurements: 9.1" min; 14.6" max
TRUNNION BRACKETS
CONDUIT BODY AND CONDUIT (BY OTHERS)
HOUSING PLATE
HOUSING
(To increase depth, move this fastner here)
MUST USE SEALANT OR SEALING LOCKNUT
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
1INSTALLATION INSTRUCTIONS
F-4558_041013
Luminaire for Parking GaragesTEKDEK™ LED
1. Bird Guard lays on top of casting.
TD17 SERIESIMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ÊTRE INSTALLÉ EN CONFORMITÉ AVEC LE CODE DE L'INSTALLATION PAR UNE PERSONNE QUI connaît BIEN LA CONSTRUCTION ET LE FONCTIONNEMENT DU PRODUIT ET LES RISQUES ENCOURUS.
DISCONNECT POWER TO ALL CIRCUITS BEFORE WIRING FIXTURE. INSTALL IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL CODES. DO NOT CONNECT TO AN UNGROUNDED SUPPLY. READ ALL FIXTURE MARKINGS AND LABELS TO ENSURE CORRECT INSTALLATION OF FIXTURE.
SUPPLEMENTAL INSTRUCTIONS MAY BE LOCATED ON THE FIXTURE, IN ADDITION TO THIS INSTRUCTION SHEET, REGARDING ORIENTATION, OR MOUNTING RESTRICTIONS.
SAVE THESE INSTRUCTIONS
Pendant Mount
Trunnion Kit
BIRD GUARD INSTALLATION - PENDANT MOUNT & TRUNNION KIT
(For Trunnion Kit remove tabs)
2. Attach both sides with (4) screws provided.
NOTE: For LEL option, align hole in bird guard with LED indicator
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
3INSTALLATION INSTRUCTIONS
F-4257_041013
MOUNT FIXTURE WITH REGARDS TO OPTICAL ALIGNMENT KEY DIRECTION
TYPES II, III, IV
TYPE V, NORMALTYPE V, SQUARE
TYPE II
TYPE III
TYPE IV
TYPE VNORMAL
TYPE VSQUARE
LIGHT DISTRIBUTION PATTERN TYPES
DRIVING LANE
DRIVING LANE
KEY OPTICALALIGNMENT KEY
This limited warranty is provided by Kenall (the Seller) to you (the Purchaser)as original purchaser of the LED lighting product. This limited warranty may be transferred to subsequent purchasers of the product as long as it is in its original packaging. Qualifying Kenall LED products shall be warranted by Kenall, for a period of ten (10) years from the date of manufacture, to be free of defects in workmanship, materials, LED lamps and internal power regulation components against defects that result in an excessive lumen depreciation, as defined by L70 Luminaire Lifetime (L70) or when at least 10% of the discrete LED sources fail to illuminate. L70 shall be defined as 70% of the published warranty luminous flux at time of manufacture using IESNA LM-79-08 testing methods. Click here for full warranty information.
Kenall reserves the right to issue credit, repair, or replace the defective merchandise, at its discretion, upon notification and confirmation by its local representative of the defect. Kenall also reserves the right to test and examine the defective product if the defect is questionable and to deny the warranty herein for any product altered, improperly installed, installed in applications for which it is not intended. This includes operation in ambient temperatures above stated limits for any length of time. Failure by electrical surge shall not be covered under warranty.
Kenall assumes no responsibility for labor or freight costs incurred in connection with the installation, removal, or replacement of products determined to be defective or any other consequential or incidental damages arising from the use of the product. Kenall’s entire liability on any claim of loss or damage resulting from a defective product is limited to the replacement price of the product.
For technical assistance, call 1-800-4KENALL (1-800-453-6255).
WARRANTY
CUSTOMER SERVICE
When you see this image, you will know the Kenall product shown or described is designed and manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. May be covered by patents found at www.kenall.com/patents. Content of speci�cation sheets is subject to change; please consult www.kenall.com for current product details. © 2015 Kenall Mfg. Co. All rights reserved.
www.kenall.com P: 800-4-Kenall F: 262-891-9701 10200 55th Street Kenosha, Wisconsin 53144
9INSTALLATION INSTRUCTIONS
F-4257_041013