lecture 18
DESCRIPTION
hhhhTRANSCRIPT
Switch Mode Inverter
LECTURE #18
Switched Mode Inverter
1Switched Mode Inverter
118.1 Single-phase half-bridge inverter with resistive load.
118.1.1 Square-wave output.
318.1.2 Quasi square waveform
418.1.3 SPWM switching scheme.
618.2 Single-phase full bridge inverter with resistive load.
718.2.1 Unipolar PWM
818.2.2 Bipolar PWM
918.3 Single-phase full-bridge inverter with resistive and inductive load.
918.3.1 Square-wave output
1118.3.2 Quasi square wave output
1218.3.3 Pulse Width Modulation
18.1 Single-phase half-bridge inverter with resistive load.The half-bridge single-phase inverter as shown below could generate three types of output waveform; square-wave, quasi-square and PWM.
18.1.1 Square-wave output.
The load voltage VLoad is a square wave and having significant low-order of harmonic components as shown below. It is not favourable because the lower harmonics components required large LC to filter out the components.
18.1.2 Quasi square waveform
Also known as PHASE OPERATION. The magnitude of the fundamental is reduced and the quasi-square wave has no triplen harmonics component compare to square-wave as shown above. Therefore, the output waveform is better than the square-wave.
18.1.3 SPWM switching scheme.
The pulse-width-modulation signal is generated by comparing modulating signal (sine wave) with the carrier signal (triangular wave).
Vin = 100 VMa = 1.0
fs = 1 kHz
The quality of waveform generated using SPWM is much better than quasi-square output where no low-order of harmonics current present in the waveform as shown below. It is much easier to remove the high frequency components using small size of LC filter.
18.2 Single-phase full bridge inverter with resistive load.
All three types of switching as applied to half bridge inverter are also applicable to full bridge inverter. However PWM switching is commonly used in this circuit topology.
PWM switching
Definition of terms in PWM:
Two types of PWM: Unipolar and Bipolar.
18.2.1 Unipolar PWM
Vin = 100 VMa = 0.8
fs = 1 kHz
18.2.2 Bipolar PWM
Vin = 100 VMa = 0.8
fs = 1 kHz
The frequency spectrum of bipolar PWM is quite similar to unipolar PWM. However the magnitude of the harmonic component is larger than the fundamental. This technique has disadvantages:-
1. The output voltage jump form Vd to +Vd
2. Impose stress on the power switching devices because always perform switching for the whole cycle.
18.3 Single-phase full-bridge inverter with resistive and inductive load.
18.3.1 Square-wave output
When IGBT1 and IGBT2 turn on (assume negligible voltage drop across the IGBTs):
The above equation has a solution in terms of:
where time constant
At the start, the load current is zero.
1st half cycle (IGBT1 and IGBT2 turn on):
Start:
End:
2nd half cycle (IGBT3 and IGBT4 turn on):
Start:
End:
3nd half cycle(IGBT1 and IGBT2 turn on):
Start:
End:
Compute i(t..) until reach steady state condition.
18.3.2 Quasi square wave output
During on period:
1st on period (IGBT1 and IGBT2 turn on):
start: i(0)=0
End:
1st zero period:
start: i(t1)End:
2nd on period (IGBT3 and IGBT4 turn on):
start: i(t2)End:
2nd zero period:
start: i(t3)End:
Compute i(t..) until reach steady state condition.
18.3.3 Pulse Width Modulation
(i) Unipolar PWM
(ii) Bipolar PWM
EMBED Equation.DSMT4
EMBED Equation.3
EMBED Equation.DSMT4
EMBED Equation.3
_1251933869.unknown
_1251934070.unknown
_1251934341.unknown
_1251934575.unknown
_1251934770.unknown
_1251934243.unknown
_1251933909.unknown
_1251933949.unknown
_1251933893.unknown
_1228733733.unknown
_1251933597.unknown
_1251933862.unknown
_1251932922.unknown
_1251933520.unknown
_1251931638.unknown
_1251805334.unknown
_1228733583.unknown
_1228733640.unknown
_1228733515.unknown