lecture 4 stresses on inclined sections
TRANSCRIPT
![Page 1: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/1.jpg)
1
P4 Stress and Strain Dr. A.B. ZavatskyMT07
Lecture 4
Stresses on Inclined Sections
Shear stress and shear strain. Equality of shear stresses on perpendicular planes. Hooke’s law in shear. Normal and shear stresses on inclined sections. Maximum stresses on a bar in tension. Introduction to stress elements.
![Page 2: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/2.jpg)
2
Shear stressShear stress acts tangential to the surface of a material.
Top view
Side view
Greek letter τ (tau)V = shear forceA = area on which it acts
Average shear stress τ = V / A
(Disregard friction in the calculations to err on the conservative side.)
![Page 3: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/3.jpg)
3
Bolts in “Single shear”
P
PAverage (normal) bearing stress σB
)( surface bearing curved of area projected)(forcebearingtotal
AP
b =σ
t
A = plate thickness t x bolt diameter d
td
d
![Page 4: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/4.jpg)
4
Forces applied to the bolt by the plates
P
These forces must be balanced by a shear force in the bolt.
τ
This results in a shear stress τ.
( ) 4 2 /d
PAV
πτ ==
P
P
![Page 5: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/5.jpg)
5
P/2P/2
( )( ) 4
2 2 //
dP
AV
πτ ==
Bolts in “Double shear”
P
P
P/2 P/2
![Page 6: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/6.jpg)
6
Example of bearing stress and shear stress(based on Example 1-5, page 36, Gere, 6th ed. 2004)
A steel strut S is used as a brace for a boat hoist. It transmits a force P to the deck of a pier. The strut has a hollow square cross-section with wall thickness t. A pin through the strut transmits the compress-ive force from the strut to two gussets G that are welded to the base plate B.
Calculate:(a) the bearing stress between
the strut and the pin(b) the shear stress in the pin(c) the bearing stress between
the pin and the gussets(d) the bearing stress between
the anchor bolts and the base plate
(e) the shear stress in the anchor bolts(Gere 2004)
![Page 7: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/7.jpg)
7
P = 50 kN, t = 10 mmdiameter of pin, dpin = 20 mmthickness of gussets, tG = 15 mmdiameter of anchor bolts dbolt = 12 mmthickness of base plate tB = 10 mm
(Gere 2004)
(Gere 2004)
(a) bearing stress between strut and pin
MPa125)(2
==pindt
Pσ
pin(b) shear stress in pin
MPa6.79)4/(
)2/(2 ==pind
Pπ
τ
P/2P/2
P/2P/2
S
GG
![Page 8: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/8.jpg)
8
(Gere 2004)
(Gere 2004)
(c) bearing stress between pin and gussets
MPa3.83)(2
==pinG dt
Pσ
(d) bearing stress between anchor bolts and base plate
MPa8.79)(4
cos==
boltB dtP θσ
(e) shear stress in anchor bolts
MPa7.84)4/()4/cos(
2 ==boltd
Pπ
θτ
![Page 9: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/9.jpg)
9
These are examples of “direct shear” -- the shear stresses are a result of the direct action of a shear force trying to cutthrough the material.
V
M
Shear force diagramτmax = 3V / 2A
X-section τ
Shear stresses can also arise in an “indirect” manner – during tension, torsion, and bending.
![Page 10: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/10.jpg)
10
Equality of shear stresses on perpendicular planes
τ1
τ2
τ3
τ4
ac
b
Forces Vertical direction: τ1 (bc) = τ3 (bc)Horizontal direction: τ2 (ac) = τ4 (ac)
So τ1 = τ3 and τ2 = τ4
![Page 11: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/11.jpg)
11
Combining this with the previous result gives τ1 = τ2 = τ3 = τ4 = τ , which called “pure shear”.
τ1 (bc)
a
bτ3 (bc)
τ4 (ac)
τ2 (ac)
So τ1 = τ2 and τ3 = τ4
about [ τ3 (bc) ] (a) = [ τ4 (ac) ] (b)Moments about [ τ1 (bc) ] (a) = [ τ2 (ac) ] (b)
![Page 12: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/12.jpg)
12
Shear strainShear stresses have no tendency to elongate or shorten;
instead they produce a change in shape.
This change in shape is quantified by the angle γ, the shear strain.The angle is measured in radians, not degrees.
Greek letter γ (gamma)
γ γ
τγ/2
γ/2
![Page 13: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/13.jpg)
13
Hooke’s Law in shear
τ = G γG is the shear modulus of elasticity (or “modulus of rigidity”).Units are N / m2 = Pa.
For mild steel, E = 210 GPa and G = 81 GPa. For aluminium alloy, E = 72 GPa and G = 28 GPa.
Since 0 < ν < 0.5 for most materials, G is typically one-third to one-half E.
( ) 12 ν+=
EG
It can be shown that the elastic constants E and G are related by:
![Page 14: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/14.jpg)
14
Normal and shear stresses on inclined sections
To obtain a complete picture of the stresses in a bar, we must consider the stresses acting on an “inclined” (as opposed to a “normal”) section through the bar.
PP
Normal sectionInclined section
Because the stresses are the same throughout the entire bar, thestresses on the sections are uniformly distributed.
P Inclined section P Normal
section
![Page 15: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/15.jpg)
15
P P
2D view of the inclined section
P σx = AP / x
y
Area A
2D view of the normal section(but don’t forget the thickness perpendicular to the page)
![Page 16: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/16.jpg)
16
P Pθ
x
y p
q
n
m
Specify the orientation of the inclined section pq by the angle θbetween the x axis and the normal to the plane.
“Normal section” θ = 0°Top face θ = 90°
Left face θ = 180°Bottom face θ = 270° or -90°
PV
N
P
θ
x
y
The force P can be resolved into components:Normal force N perpendicular to the inclined plane, N = P cos θShear force V tangential to the inclined plane V = P sin θ
![Page 17: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/17.jpg)
17
If we know the areas on which the forces act, we can calculate the associated stresses.
x
y
areaA
area A( / cos )θ
σθ
( ) 2 cos12
cos
cos cos cos
2x
2
θσθσσ
θθθσ
θ
θ
+==
====
x
AP
AP
AreaN
AreaForce
/
x
y
τθ
areaA
area A( / cos )θ
( ) 2 sin2
cos sin
cos sin cos sin
x θσθθστ
θθθθτ
θ
θ
x
AP
AP
AreaV
AreaForce
−=−=
−=−
=−
==/
![Page 18: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/18.jpg)
18
Sign convention
x
yτθ
σθ
θ
Normal stresses σθ positive for tension.
Shear stresses τθ positive when they tend to produce counterclockwiserotation of the material.
Note that these equations are derived from statics onlyand are therefore independent of the material (linear or non-linear, elastic or inelastic).
![Page 19: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/19.jpg)
19
Plot σθ and τθ versus θ.
σθ = σx at θ = 0° This is σmax.σθ = σx/2 at θ = ± 45°σθ = 0 at θ = ± 90° No normal stresses on sections cut
parallel to the longitudinal axis.
τθ = 0 at θ = 0°, 90°τθ = τmax = ± σx/2 at θ = -/+ 45° |τmax| = |σx/2|
![Page 20: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/20.jpg)
20
Example of stresses on inclined sections(based on Example 2-11, page 114, Gere, 6th ed. 2004)
A compression bar with a square cross section of width b must support a load P = 36 kN. The bar is constructed from two pieces of material that are connected by a glued joint (known as a scarf joint) along plane pq which is at an angle α = 40º to the vertical.
The material is a structural plastic with σallow (compression) = 7.6 MPaτallow = 4.1 MPa
The glued joint hasσallow (compression) = 5.2 MPaτallow = 3.4 MPa
Determine the minimum width b of the bar.
(Gere 2004)
![Page 21: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/21.jpg)
21
Values of σx based on allowable stresses in the plastic:
Maximum compressive stress is -7.6 MPa = σx
Maximum shear stress is 4.1 MPa = |τmax| = |σx/2| at θ = ±45ºThis gives σx = -2τmax = -8.2 MPa
x
x
Pb
bPAP
σ
σ
/
// 2
=
==
(Gere 2004)
x
Smallest σx governs the design.
![Page 22: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/22.jpg)
22
x
yτθ
σθ
θ
Values of σx based on allowable stresses in the glued joint:
( )
MPa6.12)50(2 cos1
)2.5(22 cos1
2
2 cos12
−=−+
−=
+=
+=
x
x
x
x
σ
σ
θσσ
θσσ
θ
θ( )
MPa9.6)50(2sin
)4.3(22sin
2
2sin 2
−=−
−−=
−=
−=
x
x
x
x
σ
σ
θτσ
θστ
θ
θ
(P/A)p
q α = 40ºθ = -50º
![Page 23: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/23.jpg)
23
mm72.2m0722.0
)109.6()1036(
/
6
3
==
×−×−
=
=
bb
b
Pb xσ
Smallest σx = -6.9 MPa (shearing of glue joint)
(Gere 2004)
![Page 24: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/24.jpg)
24
Introduction to stress elementsStress elements are a useful way to represent stresses acting at some point on a body. Isolate a small element and show stresses acting on all faces. Dimensions are “infinitesimal”, but are drawn to a large scale.
x
y
z
σ = x P A/σx
x
y
σx σ = x P A/
P σx = AP / x
y
Area A
![Page 25: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/25.jpg)
25
Maximum stresses on a bar in tension
PPa b
σx = σmax = P / Aσx
aNo shear stresses
![Page 26: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/26.jpg)
26
bσx/2
σx/2
τmax = σx/2
θ = 45°
In case b (θ = 45°), the normal stresses on all four faces are the same, and all four shear stresses have equal and maximummagnitude.
Angle σθ τθθ = 45° σx/2 -σx/2θ = 135° σx/2 σx/2θ = -45° σx/2 σx/2θ = 225° σx/2 -σx/2
PPa b
![Page 27: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/27.jpg)
27
If the bar is loaded in compression, σx will have a negative value and stresses will be in the opposite directions.
b−σx/2
−σx/2
|τmax| = |σx/2|−σx = -P / A−σx
a
Even though the maximum shear stress in an axially loaded bar is only half the maximum normal stress, the shear stress may cause failure if the material is much weaker in shear than in tension.
![Page 28: Lecture 4 Stresses on Inclined Sections](https://reader030.vdocument.in/reader030/viewer/2022020108/5865872b1a28abd75a8ba9d3/html5/thumbnails/28.jpg)
28
Examples
Wood block in compression fails by shearing on 45°planes
Mild steel loaded in tension. Visible “slip bands” (Lüders bands) appear on the sides of the bar at approximately 45° to the axis of loading when the yield stress is reached. These indicate that the material is failing in shear along planes of maximum shear stress (cup-and-cone failure).
Note that uniaxial stress (simple tension or compression in one direction) is just a special case of a more general stress stateknown as “plane stress”.