lecture 8: oscillators noise in electronic systems
DESCRIPTION
Lecture 8: Oscillators Noise in electronic systems. Oscillators Wien-Bridge Relaxation Oscillator Noise Noise Type of Noise Noise Sources. Oscillators. An oscillator is a circuit that produces a periodically oscillating waveform on its output with dc input. Two major classifications: - PowerPoint PPT PresentationTRANSCRIPT
![Page 1: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/1.jpg)
LECTURE 8:
OSCILLATORSNOISE IN ELECTRONIC SYSTEMS
![Page 2: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/2.jpg)
OscillatorsWien-BridgeRelaxation Oscillator
NoiseNoiseType of NoiseNoise SourcesNoise Analysis
![Page 3: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/3.jpg)
OSCILLATORSAn oscillator is a circuit that produces a periodically oscillating waveform on its output with dc input.
Two major classifications:o Feedback oscillatorso Relaxation oscillators
![Page 4: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/4.jpg)
FEEDBACK OSCILLATORSFeedback oscillator operation is based on the principle of positive feedback.
A fraction of output signal is returned to input with no net phase shift resulting in a re-inforcementof the output signal.
![Page 5: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/5.jpg)
FEEDBACK OSCILLATORS
Conditions of Oscillations:
i. The phase shift around the feedback loop must be 0 degree.
ii. Closed feedback loop gain Acl must be 1.
![Page 6: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/6.jpg)
FEEDBACK OSCILLATORSVf is amplified to produce the output voltage , which in turn produces the feedback voltage.
A loop is created and signal sustain itself and produces continuous oscillations.
In some types of oscillators feedback shifts the phase by 180. inverting amplifier are used there to produce another 180 degree
![Page 7: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/7.jpg)
START-UP CONDITIONS Feedback oscillators require a small disturbance such as that
generated by thermal noise to start oscillations. This initial voltage starts the feedback process and oscillations.
The feedback circuit permits only a voltage with a frequency equal to selected frequency to appear in phase on the amplifier’s input.
![Page 8: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/8.jpg)
WIEN-BRIDGE OSCILLATORSRC feedback is used in various lower frequency (up to 1 MHz) sine-wave oscillators.
At resonant frequency fr the attenuation of the circuit is 1/3.
The lead-lag circuit is used in the feedback of Wien-Bridge oscillator.
It gives 0 phase shift and 1/3 attenuation at resonant frequency.
![Page 9: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/9.jpg)
WIEN-BRIDGE OSCILLATORSThe basic Wien-bridge uses the lead-lag network to select a specific frequency that is amplified. The voltage-divider sets the gain to make up for the attenuation of the feedback network.
The non-inverting amplifier must have a gain of exactly 3.0 as set by R1 and R2 to make up for the attenuation.
If it is too little, oscillations will not occur; if it is too much the sine wave will be clipped.
Vout
–
+
R4R3
R2
R1
C1C2
Voltage-divider
Lead-lag network
Basic Circuit Wien Bridge Oscillator
![Page 10: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/10.jpg)
WIEN-BRIDGE OSCILLATION CONDITIONS
The phase shift around the positive feedback loop must be 0o and the gain around the loop must be 1.
The 0o phase-shift condition is met when the frequency is fr.
![Page 11: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/11.jpg)
WIEN-BRIDGE OSCILLATOR STARTUP
The loop gain should be greater than 1 at startup to build up output.
![Page 12: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/12.jpg)
WIEN-BRIDGE OSCILLATOR STARTUP
![Page 13: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/13.jpg)
RELAXATION OSCILLATOR
A simple relaxation oscillator that uses a Schmitt trigger is the basic square-wave oscillator.
The two trigger points, UTP and LTP are set by R2 and R3. The capacitor charges and discharges between these levels:
The period of the waveform is given by:
31
2
22 ln 1
RT RC
R
3UTP
2 3max
RV VR R
3LTP
2 3max
RV V
R R
Vout
–
+R2
R3
R1
Vf
VC
C
![Page 14: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/14.jpg)
NOISENoise is a random fluctuation in an electrical signal.
Noise in electronic devices varies greatly, as it can be produced by several different effects.
Noise is a fundamental parameter to be considered in an electronic design as it typically limits the overall performance of the system.
![Page 15: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/15.jpg)
Noise is a purely random signal, the instantaneous value and/or phase of the waveform cannot be predicted at any time.
The amplitude of the signal has very nearly a Gaussian probability density function.
![Page 16: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/16.jpg)
Noise can either be generated internally in the op amp, from its associated passive components, or superimposed on the circuit by external sources.
“External” refers to noise present in the signal being applied to the circuit or to noise introduced into the circuit by another means, such as conducted on a system ground or received on one of the many antennas formed by the traces and components in the system.
EXTERNAL AND INTERNAL NOISE
![Page 17: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/17.jpg)
TYPES OF INTERNAL NOISE
Thermal Noise Shot Noise Flicker Noise Burst Noise Avalanche Noise
Some or all of these noises may be present in a design, presenting a noise spectrum unique to the system.
It is not possible in most cases to separate the effects, but knowing general causes may help the designer optimize the design, minimizing noise in a particular bandwidth of interest.
![Page 18: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/18.jpg)
THERMAL NOISEGenerated by the random thermal motion of charge carriers (usually electrons), inside an electrical conductor.
It happens regardless of any applied voltage.
Power Spectral Density is nearly equal throughout the frequency spectrum, approximately white noise.
![Page 19: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/19.jpg)
THERMAL NOISE
The RMS voltage due to thermal noise , generated in a resistance R (ohms) over bandwidth Δf (hertz), is given by:
The noise from a resistor is proportional to its resistance and temperature.
Lowering resistance values also reduces thermal noise.See example in section 10.3.2 ‘Op-amp for every one’
![Page 20: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/20.jpg)
SHOT NOISEThe name ‘Shot Noise’ is short of Schottky noise, also called quantum noise.
It is caused by random fluctuations in the motion of charge carriers in a conductor.
![Page 21: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/21.jpg)
SHOT NOISESome characteristics of shot noise:
Shot noise is always associated with current flow. It stops when the current flow stops.
Shot noise is independent of temperature.
Shot noise is spectrally flat or has a uniform power density, meaning that when plotted versus frequency it has a constant value.
Shot noise is present in any conductor
![Page 22: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/22.jpg)
FLICKER NOISE
Flicker noise is also called 1/f noise. Its origin is one of the oldest unsolved problems in physics.
It is present in all active and many passive devices.
It may be related to imperfections in crystalline structure of semiconductors, as better processing can reduce it.
![Page 23: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/23.jpg)
FLICKER NOISE
Some characteristics of flicker noise:
It increases as the frequency decreases, hence the name 1/f
It is associated with a dc current in electronic devices
It has the same power content in each octave (or decade)
![Page 24: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/24.jpg)
BURST NOISEBurst noise consists of sudden step-like transitions between two or more levels.
is related to imperfections in semiconductor material and heavy ion implants.
As high as several hundred microvolts.
Lasts for several milli-seconds.
Burst noise makes a popping sound at rates below 100 Hz when played through a speaker — it sounds like popcorn popping, hence also called popcorn noise.
Low burst noise is achieved by using clean device processing, and therefore is beyond the control of the designer.
![Page 25: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/25.jpg)
AVALANCHE NOISEAvalanche noise is created when a PN junction is operated in the reverse breakdown mode.
Under the influence of a strong reverse electric field within the junction’s depletion region, electrons have enough kinetic energy.
They collide with the atoms of the crystal lattice, to form additional electron-hole pair.
These collisions are purely random and produce random current pulses similar to shot noise, but much more intense.
![Page 26: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/26.jpg)
AVALANCHE NOISEWhen electrons and holes in the depletion region of a reversed-biased junction acquire enough energy to cause the avalanche effect, a random series of large noise spikes will be generated.
The magnitude of the noise is difficult to predict due to its dependence on the materials.
![Page 27: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/27.jpg)
MEASURING NOISE RMS, P-P or PDFInstantaneous noise voltage amplitudes are as likely to be positive as negative.
Noise values form a random pattern centered on zero.
Since amplitudes vary randomly with time, they can only be specified by a probability density function, most commonly by Gaussian density function.
σ is the standard deviation of the Gaussian distribution and the rms value of the noise voltage and current.
The instantaneous noise amplitude is within ±1σ 68% of the time, is within ±3σ of the mean 99.7% of the time and within ±3.4σ 99.94% of the time.
![Page 28: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/28.jpg)
SIGNAL TO NOISE RATIOThe noisiness of a signal is defined as:
In other words, it is a ratio of signal voltage to noise voltage (hence the name signal-to-noise ratio).
![Page 29: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/29.jpg)
MULTIPLE NOISE SOURCES
When there are multiple noise sources in a circuit, the total root-mean-square (rms) noise signal is the square root of the sum of the average mean-square values of the individual sources:
If there are two noise sources of equal amplitude in the circuit, the total noise is not doubled (increased by 6 dB).
It only increases by 3 dB. Consider a very simple case, two noise sources with amplitudes of 2 Vrms:
![Page 30: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/30.jpg)
NOISE UNITInternal noise is normally specified as a noise spectral density in rms volts or amps per root Hertz, V/√Hz or A /√ Hz.
In datasheet it is often expressed with a plot:
Example:An op-omp TLE2027 has noise specification of 2.5 nV/ √ Hz
Noise characteristic for TLE2027
http://www.ti.com/lit/ds/symlink/tle2027.pdf
![Page 31: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/31.jpg)
EQUIVALENT NOISE EINTLE2027 is used in a system that operates over an audio frequency range of 20 Hz to 20 kHz with a gain of 40db (100).
Equivalent noise over the whole bandwidth is :
2.5nV * 2.5nV * 141.35EIN = 353.38nV
If the gain of the system is 100
Eout= 353.38nV x 100 = 35.3 microV
Noise characteristic for TLE2027
![Page 32: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/32.jpg)
CALCULATING SNR If the output signal is of 1V
SNR = 1V/ 35.3 uV = 28328
SNRdB= 20log(28328) = 89 dB
Noise characteristic for TLE2027
![Page 33: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/33.jpg)
CORNER FREQUENCY NOISE IN SPECTRAL DENSITY
Usually a plot for Noise Spectral Density is given in op-amp datasheets.
These graphs usually show two distinct regions:o Lower frequencies where pink noise
is the dominant effect
o Higher frequencies where white noise is the dominant effect
The point in the frequency spectrum where 1/f noise and white noise are equal is referred to as the noise corner frequency, fnc
![Page 34: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/34.jpg)
CORNER FREQUENCY IN NOISE SPECTRAL DENSITY
The point in the frequency spectrum where 1/f noise and white noise are equal is referred to as the noise corner frequency, fnc
The fnc can be determined visually from the graph:
Take the white noise portion of the curve, and extrapolate it down to 10 Hz as a horizontal line.
White noise
Take the portion of the pink noise from 10 Hz to 100 Hz, and extrapolate it as a straight line.
The point where the two intercept is fnc, the point where the white noise and pink noise are equal in amplitude.
Pink noise
![Page 35: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/35.jpg)
CORNER FREQUENCYOnce the corner frequency is known, the individual noise components can be added together (if the bandwidth includes corner frequency):
If fnc is not included in bandwidth, all of the contribution will be from either the 1/f noise or the white noise.
Similarly, if the bandwidth is very large, and extends to three decades or so above fnc, the contribution of the 1/f noise can be ignored.
![Page 36: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/36.jpg)
OP-AMP CIRCUIT NOISE MODEL
Noise in op-amp circuits can be modeled as voltage noise source and current noise source.
Input voltage noise is always represented by a voltage source in series with the non-inverting input.
Input current noise is always represented by current sources from both inputs to ground.
![Page 37: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/37.jpg)
INVERTING OP-AMP CIRCUIT NOISE MODEL
e1 R1
e2 R2
E0
e3
Sources e1, e2 and e3 represent the thermal noise contribution from the resistors.
Note: Noise current sources are missing here.
![Page 38: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/38.jpg)
NONINVERTING OP AMP CIRCUIT NOISE MODEL
Sources e1, e2 and e3 represent the thermal noise contribution from the resistors.
Note: Noise current sources are missing here.
![Page 39: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/39.jpg)
GENERAL NOISE MODEL
Figure describes the noise model for the non-inverting amplifier configuration showing all noise sources.
In addition to the intrinsic input voltage noise (en) and current noise (in=in+=in-) sources, there also exists thermal voltage noise (et 4 TR = k ) associated with each of the external resistors.
eni
Input Noise expression:
![Page 40: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/40.jpg)
NON-INVERTING NOISE MODEL
Output Noise expression:
Eo
Adding input noise from signal source at non-inverting input:
![Page 41: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/41.jpg)
INVERTING NOISE MODEL
Output Noise expression:
Eo
Adding input noise from signal source at inverting input:
![Page 42: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/42.jpg)
REDUCING RESISTANCE VALUES
Reducing resistance value can help in reducing thermal noise.
![Page 43: Lecture 8: Oscillators Noise in electronic systems](https://reader035.vdocument.in/reader035/viewer/2022062501/56816938550346895de0a0ab/html5/thumbnails/43.jpg)
THANK YOU