lecture3 advanced rfic design elen359a, lecture 3 gilbert cell mixers
DESCRIPTION
introduce how to design a RFIC Gilbert Mixer using ADSTRANSCRIPT
-
Advanced RFIC Design ELEN359A, Lecture 3: Gilbert
Cell MixersInstructor: Dr. Allen A Sweet
Copy Right 2004
-
All of Design is the Art and Science of Navigating Tradeoffs
Science gives us the tools to understand what nature, in the form of the laws of physics, will allow us to do and not to do.
Tradeoffs are the points where we as designers must make decisions.
The Art of design is the process by which we make good decisions given numerous factors such as economics, market acceptance, cost of development, competitive pressures, etc.
Copy Right 2004
-
Basic Non Linear Process Produces Mixer Action
Active Device Non Linearity is Expressed as a Power Series relating the devices Voltage and Current: I(t) = I0 + k1V + k2V*2 + k3V*3 +
If V = V1 + V2 (two input signals), the second order term becomes: k2(V1*2 + V1V2 + V2*2). It is the V1V2 product term that produces mixing action because if V1 and V2 are sin waves, their produce, (v1cosW1t)x(v2cosW2t) = (v1v2/2)[cos(W1-W2)t + cos(W1+W2)t] contain the sum and difference mixing Frequencies.
Copy Right 2004
-
Down Converting Mixer: Applications to Receivers
FI=Fl-Fr
Copy Right 2004
-
Up Converting Mixer: Applications To Transmitters
FR=Fl+/-FIUSBLSB
Copy Right 2004
-
Double Balanced Diode Mixer Topology
L VirtualGround
R VirtualGround
Copy Right 2004
-
Diode IV Characteristics
Copy Right 2004
-
VBIC Diode IV
Copy Right 2004
-
ADS Schematic of a Balanced 4 Diode Mixer
Copy Right 2004
-
HB Controller, Gain Equation and RF Source
Copy Right 2004
-
LO Source
Copy Right 2004
-
HB Controller
Copy Right 2004
-
HB Controller to Sweep RF_pwr
Copy Right 2004
-
Conversion Loss vs RF_pwr
Gain CompressionBegins
Copy Right 2004
-
HB Controller to Sweep LO_pwr
Copy Right 2004
-
HB Controller to Sweep LO_pwr
Copy Right 2004
-
Conversion Loss vs LO_pwr
(LO Amp Requires100 mA Current @30 % efficiency)
(Preamp Requires20 mA Current to Boost Gain to +10 dB)
Copy Right 2004
-
Single Balance Bipolar Transistor Multiplying Mixer Topology
Vi = Vl x Vr
Q1 collector currentControls Transconductance
Copy Right 2004
-
Advantages of a Single Balanced Bipolar Transistor Multiplier
High Conversion Gain (5 to 10 dB) High L to R Isolation (but not high L to I
Isolation). Low LO power Requirement (-10 to 0
dBm). IIP3 is higher than the LO power level. Low DC Power, Small size
Copy Right 2004
-
Double Balanced (Gilbert Cell) Bipolar Transistor Mixer
Copy Right 2004
-
Advantages of a Gilbert Cell Transistor Mixer
All Three ports are differential, which is a natural configuration for creating Quadrature Phase Modulators and Detectors.
L to R, L to I Isolations are excellent. All the Advantages of the Single Balanced
Transistor Mixer are available in this case.
Copy Right 2004
-
A Direct Conversion Receiver using Gilbert Cell Mixers
Copy Right 2004
-
Gilbert Cell Mixer Topology
Copy Right 2004
-
Fully Differential Mixer Cell
Copy Right 2004
-
Series Diode Bias Tree
Copy Right 2004
-
DC Power and Output Term
Copy Right 2004
-
RF and LO Sources
Copy Right 2004
-
HB Controller and Equations
Copy Right 2004
-
Harmonic Balance Controller
Copy Right 2004
-
DC Analysis
Copy Right 2004
-
Bias Tree DC Levels
Copy Right 2004
-
MIX Function Determines Frequency Index
Copy Right 2004
-
Basic Simulation Calculates Conversion Gain in Two Ways
Copy Right 2004
-
LPF Eliminates Spurious Signals in the Mixers Output
Copy Right 2004
-
Mixer Simulation including an Output LPF.
Copy Right 2004
-
HB Controller to Sweep LO_pwr
Copy Right 2004
-
HB Controller to Sweep LO_pwr
Copy Right 2004
-
Simulation of Gain vs LO_pwr
Copy Right 2004
-
HB Controller for Sweeping RF_pwr
Copy Right 2004
-
HB Controller to Sweep RF_pwr
Copy Right 2004
-
Simulated Gain vs RF_pwr
(P-1dB)
Copy Right 2004
-
S Parameter Controller Simulates Isolations and Matches
Copy Right 2004
-
Matches and Isolations of a Gilbert Cell Mixer
Copy Right 2004
-
Disabling one Transistor Creates Imbalance and Poor Isolation
Copy Right 2004
-
Gilbert Cell Up Converter
(i.e. F2+/-F1)
Copy Right 2004
-
Up Converting Mixer HB Controller and Equations
Copy Right 2004
-
Sources for Up Converting Mixer
Copy Right 2004
-
BPF Selects a USB or an LSB Output
Copy Right 2004
-
Up Converter Simulation Including MIX Function Table
Copy Right 2004
-
USB Output is Selected with the BPF
Copy Right 2004
-
HB Controller and Equations to Simulate OIP3
Copy Right 2004
-
LO and RF Sources for Intermodulation Simulations
Copy Right 2004
-
HB Controller-Freq
Copy Right 2004
-
HB Controller-Sweep
Copy Right 2004
-
HB Controller- Solver
Copy Right 2004
-
HB Controller- Params
Copy Right 2004
-
MIX Function Determines Frequency Index for each Signal
Copy Right 2004
-
Intermodulation Spectrum
Copy Right 2004
-
Gain and OIP3(upper and lower) vs LO_pwr
(dBm)
(dB)
Copy Right 2004
-
LO and RF Sources to Simulate Non Linear Noise Figure
Copy Right 2004
-
HB Controller and Equations for Noise Figure Simulation
Copy Right 2004
-
HB Controller-Freq
Copy Right 2004
-
HB Controller-Params
Copy Right 2004
-
HB Controller- Noise(1)
Copy Right 2004
-
HB Controller-Noise (2)
Copy Right 2004
-
HB Controller-Solver
Copy Right 2004
-
HB Controller- Output
Copy Right 2004
-
Simulated ssb Noise Figure
Copy Right 2004
-
Simulated Noise Figure (dsb) and Conv Gain
Copy Right 2004
-
Noise Voltage Output at 400 MHz in a 1 Hz Bandwidth
Copy Right 2004
-
Home Work #2:A Down Converting Mixer for Wi-Fi
Copy Right 2004
Design a Down Converting Gilbert Cell Mixer for 802.11B (RF_freq=2400 MHz). This mixer will down convert received Wi-Fi signals to an IF frequency of 850 MHz where a cellular/PCS receiver will process them. Conversion gain is to be at least 10 dB. As part of the design, an integral HPF (designed per lecture 2) in front of the mixer will reduce PCS interference at 1800 MHz by at least 20 dB.
LO_pwr=-10 dBm, Vcc=+5.0 volts, Ic=10 mA max. All transformers are off chip.
-
Home Work #3: Advanced Wi-Fi Mixer
Simulate the three isolations, the three matches, P-1dB compressed power, upper and lower OIP3, and the large signal noise figure for the mixer you designed in home work #2.
Layout your Wi-Fi mixer using Knowledge On design rules. All three radio frequency ports (RF, LO, and IF) are to be pairs of standard bonding pads, spaced by 150 microns (c-c) which can be bonded to three off chip transformers. A 7th pad is Vcc. Keep your layout as square as possible.
Copy Right 2004