led electrical specification for g5s40wxxxlrp
TRANSCRIPT
Item
Nominal voltage
Nominal frequency
AC voltage range
DC voltage range (start)
DC voltage range (operation)
Maximum voltage
Nominal current
G5S40W700LRP
G5S40W800LRP
G5S40W900LRP
G5S40W1050LRP
Total Harmonic Distortion (THD)
Power factor
Displacement factor
Efficiency
No-load power
Stand-by power
Protection class
Inrush current
Earth leakage current
Nominal voltage range
G5S40W700/800/900LRP
G5S40W1050LRP
Maximum voltage
Nominal current range
G5S40W700LRP
G5S40W800LRP
G5S40W900LRP
G5S40W1050LRP
Current accuracy
Typical output LF current ripple
Full load @230VAC
Ou
tpu
t
Low Frequency< 120Hz
Full load @230VAC
700mA
800mA
1050mA
900mA
± 3%
± 5%
Full load @230VAC
30-42Vdc
Remark
Full load @230VAC
Value
Inp
ut
NA
NA
LED Electrical Specification for G5S40WXXXLRPConstant current LED Driver
53Vdc
NA
30-40Vdc
Full load @230VAC
220-240V
NA
50–60Hz
264Vac
198-264V
NA
10A / 300us
220mA
190mA
170mA
NA
230mA
< 15%
0.9C
89% (Typ.)
0.9C
Approval Marks
© HEP,LC-20-07-01
Item Value Remark
Starting time Full load @230VAC
Nominal power range
G5S40W700LRP
G5S40W800LRP
G5S40W900LRP
G5S40W1050LRP
Maximum power
Dimming control
Dimming technique
PWM frequency
Dimming range
Lowest dimming current
Galvanic isolation
Ambient temperature range ta
Maximum case temperature tc
Max. case temp. in fault condition
Storage temperature range
Relative humidity
Surge transient protection
Environmental rating
IP rating
Mains switching cycles
Expected lifetime
Gross weight/box
Net weight/box
Pcs/box
Dimension/box
Protections
Short- & open circuit proof, Auto. Overload protection
Conformity & Standards
Safety standard: EN 61347-1, EN 61347-2-13, EN 62493
Performance: EN 62384
SAA standard: AS/NZS 61347.1, AS/NZS IEC 61347.2.13
CCC standard: GB17625.1,GB/T17743,GB19510.1,GB19510.14
EMC standard: EN 55015, EN 61000-3-2, EN 61000-3-3, EN 61547
< 0.5 S
Ou
tpu
tD
imm
ing
Packin
gE
nv
iro
nm
en
t
> 50,000 h, tc 90 °C @ ta 50 °C
> 100000 h, tc 80 °C @ ta 40 °C
42W
NA
NA
> 100,000
-30°C - +85°C
10% - 95%
1 kV
Indoor
IP20
NA
When operating under fault conditions,
the temperature of the enclosure at any
location should not exceed 110 °C
L/N
24-33.5W
27-38W
31.5-42W
21-29.5W
0.2 % / 1,000 h failure rate
9.8 kg
64 PCS
8.7 kg
415(L)*255(W)*240(H)mm
-20°C - +50°C
110°C
NA
NA
NA
90°C
© HEP,LC-20-07-01
Cable information
PRI Connection L N
Color Brown Blue
Wire type 7022 7022
Wire diameter AWG18 AWG18
Wire length 132mm 134mm
Stripping 6mm 6mm
Tolerance ±5mm ±5mm
Sec Connection + -
Color Red Black
Wire type 1332 1332
Wire diameter AWG20 AWG20
Wire length 238mm 235mm
Stripping 5mm 5mm
Tolerance ±5mm ±5mm
▉Electrical Values
*Subject to change without notice, HEP guarantees all products perform functionally well*
0.85
0.90
0.95
1.00
0 70 80 90 100
Po
we
r fa
cto
r
Load (%)
Power factor vs Load
700 800 900 1050
80
85
90
95
100
0 70 80 90 100
Effi
cie
ncy
[%
]
Load [%]
Efficiency vs Load
700 800 900 1050
2
6
10
14
18
70 80 90 100
THD
[%
]
Load [%]
THD vs Load
700 800 900 1050
© HEP,LC-20-07-01
PhysicalParameter
Housing MaterialSolderingLabel
Polycarbonate / PottingLead-Free, Comply With RoHSSurface Print
:::
Housing MaterialSolderingLabel
Polycarbonate / PottingLead-Free, Comply With RoHSSurface Print
:::
H : 32LW
: 73: 45
mm mm
mm
Tolerance : >0 ~ 100 > +/-0.5mm_ _100 > +/-1 mm_
L
M
R
N
L
W
W
H
H
N : 81LW
: 89: 45
mmM : 73 mm mm
mm H : 32R : 1.6 mm
mm
Tolerance : >0 ~ 100 > +/-0.5mm_ _100 > +/-1 mm_
Screw clip type
Clear type
Wiring Diagram
N
L
LED LED LED
Series
LED LED LED
Series
N
L ~IR
P
SE
C
~IR
P
SE
C