Unit A, Carlton Industrial Est, Cemetery Road, Yeadon, Leeds, LS19 7BD www.loxa.co.uk

LED External Floodlight

• IdealreplacementsforHalogens,SONsandMetalHalide• Saveupto90%onenergycosts• Instantstart.Flickerfree• Nomercuryorotherhazardousmaterials• 50,000hours• Lowheat

LX274-10WHB-P LX274-30WHB-P LX274-50WHB-P LX274-80WHB LX274-120WHB

* * *

Replaces 150WHalogen 500WHalogen 150WSON/100WMH 250WSON/150WMH 400WSON/250WMH

Part Code LX274-10WHB-P LX274-30WHB-P LX274-50WHB-P LX274-80WHB LX274-120WHB

PowerInput(95-245VAC50/60hz) 10W 30W 50W 80W 120W

LEDType 1xIntegrated

PowerFactor 0.95

LumenOutput >700lm(70lm/w) >2100lm(70lm/w) >3500lm(70lm/w) >5600lm(70lm/w) >8400lm(70lm/w)

BeamAngle 120°

LightColourTemperature 6500K-White

Life >50,000hours

Dimensions(WxHxD)mm 115x87x92 225x185x135 290x235x168 280x360x230 395x523x149

Construction Castalloycasing,glasslens,steelreflector

IPRating IP65

WorkingTemperature -30°c+40°c

Warranty 3years PartLcompliant

*The 10w, 30w and 50w units have a built-in socket which accepts Loxa’s new ‘plug and play’ LX313-50B PIR unit (available separately). All lamps are also suitable for use with external PIR and photocell sensors.

523m

m

395mm

149mm

PIR UnitLX313-50B

PowerInput 220-240VAC50/60hz

Workingtemperature: -10°c+55°c

Workinghumidity: <93%RH

Suggestedinstallationheight: 2.5-3.5m

Detectionangle/distance: 160°/10metres

Connection ConnectsonlytoLoxaplug‘n’playfloodlights

INSTALLATIONRemove (unscrew) and store safely the plastic dust cap A on the underside of the floodlight. Remove (pull out) and store safely the exposed jumper B from the three pin female connector.

Note: you will need to replace the dust cap and jumper should you wish to revert the floodlight to standard (non PIR) operation. Caution - the jumper must be refitted in the ‘flat to flat’ position as aligned with the three pin female connector.

Push fit the PIR three pin male connector C into exposed three pin female connector D on the floodlight. The connectors will only fit in the ‘flat to flat’ position.

Screw on the retaining ring E to finger tightness. Do not overtighten.

Setting the LX313-50BIt is easiest to initially set the PIR in daylight

1. Turn the ‘day/night’ dial to its fully clockwise position – which allows the sensor to activate during daylight.

2. Turn the TIME dial to its fully clockwise position - this sets the unit to its minimum activation time and allows stage 3 to be performed more quickly.

3. Turn the ‘day/night’ dial anticlockwise in small increments (testing the sensor after each adjustment) until the sensor will not activate. The sensor should now activate only in poor light conditions.

4. Set the TIME dial to your preferred setting between the maximum 20 minutes (fully anticlockwise) and the minimum 20 seconds (fully clockwise).

The PIR should now activate for your preferred length of time when triggered during poor light conditions. Fine adjustments can be made to activation settings after some experience of normal operation is acquired:

Turning the ‘day/night’ dial anticlockwise will restrict activation to poorer light conditions.

Turning the TIME dial anticlockwise will increase the length of time the unit will activate for once triggered.

A

B

D

C

E

Floodlight Connector