lee valley - a deluxe chisel cabinet

7/23/2019 Lee Valley - A Deluxe Chisel Cabinet

1/6

A Deluxe Chisel CabinetWoodworking Newsletter

Vol. 9, Issue 3 - January 2015

1/6 www.leevalley.com

After I nished my wall-mounted tool chest (8 x 21 x 36) a few years ago, a wise friend warned me [I]ts

one that holds disappointment in its heart. The day will certainly come when there is no more room in it for

the most recent tool.... My friend was, of course, right, and I have since been adding more storage units for

my hand tools. This chisel cabinet (5 x 12 x 27) is my latest addition and is unlikely to be my last.

Design Consideration

I wanted the new cabinet to be small enough to t in the wall space available, but with enough room for both

chisels and basic honing supplies. I use magnets to store the rasps and les in my tool chest, and decided

to do the same with my chisels. To add some elegance to the cabinet, I chose the double-offset knife hinges

to hang the door. Finally, the cabinet is deep enough that a stand-alone chisel stand can be placed on the

bottom or top shelf when, not if, more chisels are acquired.

Some woodworkers avoid knife hinges, as there is little margin for error in their installation. Using hand

tools, Ill show how you can install knife hinges in a few steps. For in-depth coverage of knife hinges, read

The Impractical Cabinetmakerby James Krenov.


2/6




Carcass Construction

The carcass is quite simple. I joined a xed shelf to the sides and attached the cabinets sides to the top

and bottom, all using Dominos (dowels can be used instead). I rst edge-jointed two boards to make thedoor, and then cut all the mortises for the Dominos. The back rabbets on the sides were cut using the skew

rabbet plane.


3/6




After drilling holes for the top shelf pins on the sides, I dry-assembled the carcass and temporarily held it

together using clamps, no glue. I cut the rear panel to size and put it aside until the nal assembly.

Installing the Door Hinges

I always mount the door-hinge leaves (the ones with pivot holes) on the door rst, as the layout is

straightforward. First, place the leaf centered and ush with the doors top edge, then scribe around the

hinge with a marking knife. Clamp the door in the vise with two support pieces to prevent splitting of the thin

mortise walls when chiselling. This also provides a wider base for the use of the router plane.

The authors favorite tool for cutting rabbets to accept both the rear panel and French cleat is the skew rabbet plane.

Try to match both the grain direction and pattern when

edge jointing the boards. Also used is a spring joint.

Group and cut all of the mortises for one batch of

workpieces before changing the Domino joiner s settings

for the next cut.


4/6




Remove the bulk of the waste in the hinge recess using chisels and a router plane. Always pre-drill before

installing the leaf. I used the same procedure for installing the hinge on the doors bottom edge.

Installing the Carcass Hinges

The layout procedure for mounting the pin-hinge leaves (the ones with the pins and washers) on

the carcass isdifferent because you need to leave a gap between the carcass and the door. The door

gap is the same as the thickness of the washer on the pin leaf. (The hinge washers I used are the same

thickness as a plastic gift card.)

With the carcass still clamped in place and starting from the xed shelf, place the pin leaf and the plastic gift

card against the side where the door is to be hung. Scribe across the end of the hinge and the elbow, and

remove the shelf from the carcass.

Place the door hinge centered and fush with the doors

edge and scribe the hinges layout lines.

You can use a power router to cut the recess, but chisels

and a router plane provide unmatched precision.

Use a gift card as a shim to set the gap for scribing the opposite end of the hinge leaf.


5/6




The author supported part of the router plane with a scrap while cleaning out the hinge mortise.

You can carefully trace the pin-hinge leaves using the marks just made as a guide, but I used a more

accurate method. It requires two wheel-marking gauges or a double-ended gauge to make two marking-

gauge settings. Set the rst gauge equal to the distance of the front edge of the door to the installed doorhinges edge; set the second one equal to that distance plus the width of the pin-hinge leaf. Using the two

settings, scribe the mortise lines on the shelf using the marking gauge. After cutting the hinge recess with

chisels and a router plane, install the pin-hinge leaf. Repeat the same steps to install the hinge leaf on the

inner top surface.

Use two wheel gauges or a double-ended gauge to

duplicate the door hinges setting to the carcass.

Lay out the pin-hinge mortise by scribing the lines with

the marking gauge.


6/6




Installing the Chisel Holders and Rear Panel

Two wood strips with magnets glued into the pre-drilled stop holes act as the chisel holders. The strips are

screwed and glued to the rear panel at the appropriate spots. Dry t the cabinet, including the door and rearpanel, to ensure everything ts before putting all the parts together with glue and screws.

Building the Drawer

The last component of the cabinet is a simple drawer for holding honing supplies. I put together the slightly

oversized drawer using Dominos again, and hand planed it to a perfect t.

Finishing

For shop builds, my preferred nish is oil, boiled linseed oil in this case. Following the advice of Tage Frid,

I avoided nishing the inside of the carcass or the outside of the drawer sides, as they might stick together.

Once the cabinet was dry, I mounted it to the wall and moved the chisels to their new home.

I have been resisting the temptation to buy more chisels, but, more than ever, this new cabinet makes it a

losing battle. We woodworkers live with the woodworking version of Parkinsons Law: tools expand so asto ll the space available!

Text and photos by Charles Mak

Charles Mak is a businessperson and enthusiastic hobby woodworker, teacher, writer and tipster. He works

part-time at his local Lee Valley Tools store.

Further Reading

Macnab, Ron. Using Magnets to Store Chisels. Lee Valley Tools Woodworking Newsletter. Vol. 6, Issue

5. May 2012.

lee valley - a deluxe chisel cabinet

Documents