legacy-gw features rev1.4 24 jan., 2013. 2 over view
TRANSCRIPT
Legacy-GW Features
Rev1.4 24 Jan., 2013
2
Over view
3
Over view
1.Use NCP/TDE ( TDA ) as a legacy GW by stacking connection
with NS1000.
2.NCP/TDE(TDA) connect with NS by stacking card working
as part of One-look network.
4
Over view
Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE)
NS1000 as stacking Master Unit
NCP500NCP1000
STACK-S card
STACK-M cardSite #1
Site #2
Site #3
Site #4 : :
LAN
Stacking Slave
Stacking Slave
Slave Units
Stacking Slave
Stacking Slave
Proprietary cable for stacking connectionThe length of the cable : 2M(Dedicate cable for these Stacking card)
Master forOne-look
5
Symbol Model Name Description Remark
STACK-M KX-NS0130 Stacking Master Card
- Interface card for Legacy-GW
- Proprietary Interface x 2 ports
Over view
Symbol Model Name Description Remark
STACK-S (NCP) KX-NS0131
Stacking EXP Card for NCP
Legacy-GW Control Unit for NCP
with Stacking Cable
STACK-S(TDE/TDA) KX-NS0132
Stacking EXP Card for TDE/TDA
Legacy-GW Control Unit for TDE/TDA
with Stacking Cable
New card
6
Condition
7
Condition 1
STACK-S card
STACK-M card
Stacking Slave #1
Stacking Slave #2
1.MPR of NCP has to be removed to install Stack-S card. This means Virtual card on NCP is not supported. All of IP terminal has to connect to NS1000.
2.Type of GW has to be same for each NS1000.
Category1: NCP500 /NCP1000
Category2: TDE100/200, TDA100/200
Category3: TDE600/620, TDA600/620
3.Max 2 GW for each NS. Max 8 for entire One-look network. 4.TDA15/30/50/100D is not supported.
5. AK is not required to use Legacy GW.
*If the type of cabinet is mixed then
2nd one will not be worked.
8
Condition 2
TDE600
TDE620
NS1000
In case of TDE600 each cabinet count as 1 GW and connection to NS has to be done by Stack-S card.
Bus card in TDE600 and TDE620 has to be removed.
TDE620
TDE620
NS1000
TDE600
TDE600
NS1000
OR OR
9
Symbol Model Description
RMT TDA0196 Analogue Modem for Remote Maintenance
MEC TDA0105/TDE0105
Memory Expansion Card
DSP4 NCP1104 VoIP channel card 4ch
DSP16 TDE0110 VoIP channel card 16ch
DSP64 TDE0111 VoIP channel card 64ch
CTI-LINK TDA0410 CTI Link Card
IP-EXT16 TDA0470 16-Channnel VoIP Extension Card
IP-GW4E TDA0484 4-Channnel VoIP Gateway Card
IP-GW16 TDA0490 16-Channnel VoIP Gateway Card
IP GW4 TDA0480 4 Channel VoIP Gateway Card
MSG4 TDA0191 4-Channel Message Card
ESVM2 TDA0192 2-Channel Simplified Voice Message Card
ESVM4 TDA0194 4-Channel Simplified Voice Message Card
CLCOT8 TDA1180 8-Port Analogue Trunk Base Card w/ Caller ID
CLCOT8E TDA1186 8-Port Analogue Trunk Daughter Card w/ Caller ID
MCSLC24 TDA1178 24-Port Single Line Telephone Card
MCSLC16 TDA1176 16-Port Single Line Telephone Card
Which Optional card can not be used at Legacy GW?
Condition 3
Basically
Optional card
1)on TDE/NCP MPR
2)Support by V5 or later
3) IP-GW, IP-EXT
4) MSG
are not supported.
10
Condition 4
How many CO can be installed in each Legacy GW?Stand-alone Stacking system
One LookNetworking
1NCP5001NCP1000
1TDE/TDA1001TDE/TDA 2001TDE/TDA 600
2NCP5002NCP1000
2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600
Trunk(ch) 256 256 600IP 256 256 256
SIP 256 256 256H.323 48 48 96
Legacy 30 0 64/64/120/128/160 128/128/240/256/256 600
LCOT 2 0 12/16/96/128/160 24/32/192/256/256 600
BRI 8 0 12/16/96/128/160 24/32/192/256/256 600
PRI23 23 0 46/46/92/92/115 92/92/184/184/230 600
PRI30 30 0 60/60/120/120/150 120/120/240/240/256 600
T1 0 0 48/48/96/96/120 96/96/192/192/240 600
E1 0 0 60/60/120/120/150 120/120/240/240/256 600
11
Condition 5
How many EXT can be installed in each Legacy GW?Stand-alone
Stacking systemOne LookNetworkin
g
1NCP1TDE/TDA1001TDE/TDA 2001TDE/TDA 600
2NCP2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600
Extension(ch) 640 640 1000IP 640 640 1000
IP-PT 256 256 1000SIP 640 640 1000
SIP Phone 640 640 1000KX-UT series 640 640 1000
S-PS(SIP based DECT) 255 255 255
Legacy *1 2 0 44/160/256/304 88/320/512/608 1000
SLT 2 0 36/96/128/240 72/192/256/480 1000
DPT 0 0 40/128/256/256 80/256/512/512 1000
12
Stand-aloneStacking system
One LookNetworking
1NCP1TDE/TDA1001TDE/TDA 2001TDE/TDA 600
2NCP2TDE/TDA 1002TDE/TDA 2002TDE/TDA 600
CS (pcs) 64 64 128
DPT-CS (2ch) 0 0 11/32/32/32 22/64/64/64 128
DPT-CS (8ch) 0 0 5/16/16/16 10/32/32/32 64
IP-CS 64 *2 64 *2 128 *2
SIP-CS 64 *3 64 *3 128 *3
PS(DECT)(pcs) 512 512 512
VM
Built-in UM (ch) 24 24 24ch x16
TVA/TVM (ch) 0 0 48 (24ch x2) 24ch x8
Condition 6
*2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs.
*3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.
How many other devices can be installed in each Legacy GW?
13
• AK on NCP/TDE can’t be transferred to NS MPR.
Condition 7
• In case of TDA100/200 and TDE100/200
OPB3 card with ECHO16 must be installed in only SLOT1.- Other than OPB3 card allows to install in any SLOT.- OPB3 card with sub-card except for ECHO16 allows installing in any SLOT.
• HGT100, NT400 can’t be connected to NS MPR.
14
How to work?
15
How to work?
Installation
• Both Stack-M and Stack-S card is non hot swappable.• Each cabinet can be power on without any order.• Initial Legacy-GW installation, all card will be initialized.• The optional service cards is hot swappable.
• TVM can be installed as VM system for entire One-look.• CS can be installed at both NS(NCP0158) and Legacy-GW (TDA0141/142/155/156/158). PS can Hand over between these CS to CS(NCP0158, TDA0141/142/155/156/158).
16
How to work?
Wireless•Hand over between NS to Legacy GW and Legacy GW to Legacy GW is available.
CS CS(TDA0141/142/155/156/158)
CS CS
IP-CS IP-CS(NCP0158)LAN
PS
•If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.
17
How to work?
Start up
LED Status
“Stack-M” LED Green On : Normal working condition Off: Error( Not Working)
“Stack-S” LED Green On : INS Red On : Fault Red Flash: OUS
Legacy GW“RUN” LED Green Off :Power off On : Running as GW Slow Flash: While start up
“ALARM” LED Red Off : No present error On : Present Error
18
How to work?
Maintenance
All below service for Legacy-GW is supported through NS1000 cabinet.
• Programming• Firmware update• Error log, Syslog• SNMP information• SMDR
19
Programming
20
Programming at NS1000
Programming
Button to switch Physical-Virtual-LegacyGW1-LegacyGW2
Each Optional Card can be selected and installed.
Stack S connect to “1” on
Stack M consider as “GW1”
21
Programming at NS1000
Programming
LPR Software name same as existing models
LPR Software for STACK-S card “PSTKS” is new!
LPR Software :Software can be download through NS1000
22
Programming at NS1000
Programming
Programming items related to Legacy GW support.
Related to VM. Related to DSS.
Port Property
23
Appendix
24
Appendix
Supported optional card
25
Appendix
Supported optional card
26
Appendix
Supported optional card
27
END
28
20120827-01 LegacyGW_Rev1_27Aug2012Mar.ppt
- 1st release
20120905-02 LegacyGW_Rev1_1_5Sep2012Mar.ppt
- Edit slide #11 revise number of legacy EXT and DPT.
- Add slide #12
20121031-03 LegacyGW_Rev1_2_31Oct2012Mar.ppt
- Add comment for slide #7 “No AK required”
- Add additional sample for slide #8
- Add comment for slide #9 “Basic idea”
- Add comment for #13 about HGT100 and NT400
- Add remark for #16
20121108-04 LegacyGW_Rev1_3_8Nov2012Mar.ppt
- correct slide #8 600-620 twice to 600-620 and 620-620
20130124-05 LegacyGW_Rev1_4_24Jan2013Mar.ppt
- correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW
Modification