levelone wbr-6001 um

8/12/2019 Levelone Wbr-6001 Um

1/86


2/86

SafetyFCC WARNING

This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless themodifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change ormodification is made.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:

1) Reorient or relocate the receiving antenna.2) Increase the separation between the equipment and receiver.3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.4) Consult the dealer or an experienced radio/TV technician for help.

CE Declaration of conformity

This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class B for ITE, the essential protection requirementof Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility.

CE Marking Warning

Hereby, Digital Data Communications, declares that this (Model-no. WBR-6001) is in compliance with the essential requirements and other relevantprovisions of Directive 1999/5/EC.

The CE-Declaration of Conformity can be downloaded at:

http://www.levelone.eu/support.php

ii


3/86

Table of Content

TABLE OF CONTENT.................................................................................................................V

1. INTRODUCTION....................................................................................................................1

USER MANUAL OVERVIEW............................................................................................................1

2. UNPACKING AND SETUP....................................................................................................3

FEATURES ..................................................................................................................................3

PACKAGE CONTENTS ...................................................................................................................3

3. HARDWARE INSTALLATION...............................................................................................5

PRODUCT LAYOUTFRONT VIEW.................................................................................................5

PRODUCT LAYOUTREAR VIEW ..................................................................................................6

HARDWARE INSTALLATION STEPS ..................................................................................................6

NETWORK CHECK........................................................................................................................8

4. CONFIGURING WIRELESS ROUTER................................................................................10

LEDINDICATOR FOR N_MAXWIRELESS ROUTER ........................................................................10

LOGIN TO CONFIGURE FROM WIZARD ............................................................................................7

BASIC SETTING .........................................................................................................................10

Primary Setup WAN Type, Virtual Computers ..................................................................10

Static IP Address...............................................................................................................12

Dynamic IP Address with Road Runner Session Management.(e.g. Telstra BigPond).....13

PPP over Ethernet ............................................................................................................13

PPTP.................................................................................................................................13

L2TP .................................................................................................................................14

Virtual Computers (Only for Static and dynamic IP address Wan type) ............................15

DHCP Server .......................................................................................................................16

Wireless setting, 802.1X setting and WDS...........................................................................17

Change Password................................................................................................................25

FORWARDING RULES .................................................................................................................26

Virtual Server .......................................................................................................................27

Special AP ...........................................................................................................................28

Miscellaneous Items.............................................................................................................29

SECURITY SETTINGS..................................................................................................................30

Packet Filter.........................................................................................................................31

Domain Filter........................................................................................................................36


4/86

URL Blocking .......................................................................................................................38

MAC Address Control ..........................................................................................................40

Miscellaneous Items.............................................................................................................43

ADVANCED SETTINGS ................................................................................................................44

System Time........................................................................................................................45

System Log..........................................................................................................................46

Dynamic DNS ......................................................................................................................47

SNMP Setting ......................................................................................................................49

Routing.................................................................................................................................50

Schedule Rule......................................................................................................................52

Qos Rule..............................................................................................................................54

TOOLBOX..................................................................................................................................55

System Log..........................................................................................................................55

Firmware Upgrade ...............................................................................................................55

Backup Setting.....................................................................................................................55

Reset to default ....................................................................................................................56

Reboot .................................................................................................................................56

APPENDIX A 802.1X SETTING .............................................................................................57

APPENDIX B WPA-PSK AND WPA.......................................................................................62

APPENDIX C FAQ AND TROUBLESHOOTING ....................................................................73

TECHNICAL SPECIFICATIONS ...............................................................................................78

vi


5/86


6/86


7/86

2. Unpacking and Setup

This chapter provides the package contents and setup information for the N_MaxWireless

Broadband Router.

Features

Extended and high-speed wireless connectivity with wireless Ntechnology

Advanced QoS Services for Intelligent Internet

Backward compliant with IEEE802.11g and 11b standards

Operates on the 2.4GHz frequency band

Stay Protected with Advanced Network Security

WEP and WPA/WPA2-PSK encryption supported along with Wi-Fi Protected Setup

Integrate 4-Port Fast Ethernet Switch with 10/100Mbps MDI-MDI-X auto-sensing

Built-in NAT function allows multiple PCs and devices to share Internet connection

Browser-based interface configuration and management

Quick Setup Wizard provides alternative way to manage device

Package Contents

Open the box of the N_MaxWireless Broadband Router and carefully unpack it. The box should

contain the following items:

WBR-6001 N_MaxWireless Broadband Router

Power Adapter

Cat.5 Cable

Antenna

CD Manual/Utility

Quick Installation Guide

If any item is found missing or damaged, please contact your local reseller for replacement.

3


8/86


9/86

3. Hardware Installation

Product Layout Front View

1) Reset

Press the Reset button to reboot device or restores factory default setting.

2) Status

A blinking light indicates the device is ready

3) WAN

A solid light indicates the WAN port is connected.

4) WLAN

A solid light indicates the Wireless segment is ready. LED blinks during wireless data transmission.

5) LAN LEDs

A solid light indicates to an Ethernet enable computer on ports 1~4.

LED blinks during data transmission.

6) WPS

Wi-Fi Protected Setup push button

5


10/86

Product Layout Rear View

1) Power Jack

Receptor for the supplied power adapter

2) LAN Ports (1~4)

Connect Ethernet devices such as computers, switches or hubs.

3) WAN Port

The WAN port is the connection for the Ethernet cable to the Cable or DSL Modem.

4) Antenna

Detachable antenna allows users to change antenna if necessary.

Hardware installation steps

Decide where to place your Wireless Broadband Router

You can place your Wireless Broadband Router on a desk or other flat surface. For optimal

performance, place your Wireless Broadband Router in the center of your office (or your home) in alocation that is away from any potential source of interference, such as a metal wall or microwave

oven. This location must be close to power and network connection.

Setup LAN connection

Wired LAN connection: connectsan Ethernet cable from your computers Ethernet port to one of

the LAN ports of this product.

Wireless LAN connection: locate this product at a proper position to gain the best transmit

performance.

6


11/86

3. Setup WAN connection

Prepare an Ethernet cable for connecting this product to your cable/xDSL modem or Ethernet

backbone.

4. Power on

Connecting the power cord to power inlet and turning the power switch on, this product will

automatically enter the self-test phase. When it is in the self-test phase,the Statusindicator will

be lighted ON for about 10 seconds, and then it will be flashed 3 times to indicate that the self-test

operation has finished. Finally, the Status indicator will be continuously flashed once per second

to indicate that this product is in normal operation.


12/86

Network Check

1. Please make sure your PC can get IP address automatically so the WBR-6001 can communicate

with your PC during configuration.

Select Control Panel > Network Connections.

Right click the Local Area Connection and choose Properties.

Select the TCP/IP protocol for your network card.

Click on the Properties button. You should then see the following screen and make sure you

have selected Obtain IP address automatically

2. Reboot computer to make sure you have received the IP address correctly.

3. Start your Web browser. In the Address box, enter WBR-6001s default IP Address:

http://192.168.0.1

4. When prompted, use the following default password to login.

Password: password

8


13/86

Default Settings

IP Address 192.168.0.1

Password password

Wireless Mode Enable

SSID WBR-6001

Security None

Please enter the default system password in lowercase only.


14/86

4. Configuring Wireless Router

LED Indicator for N_MaxWireless Router

LED Function Color Status

Description

Status flashed once per second to indicate systemis alive.

StatusSystemstatus

Green Blinking

WANWAN portactivity

Green On The WAN port is linked.

Blinking The WAN port is sending or receiving data.

WLAN Wirelessactivity

Green

Blinking Sending or receiving data via wireless

An active station is connected to the correspondingLAN port.

Link.1~4

Link status Green On

The corresponding LAN port is sending or receivingdata.

BlinkingSpeed

10/100 Data Rate Green

OnData is transmitting in 100Mbps on thecorresponding LAN port.

Reset To reset system settings to factory defaults

ButtonSpecialapplication

10


15/86

Login to Configure from Wizard

Activate your browser, and disable the proxy or add the IP address of this product into the exceptions.

Then, type this products IP address in the Location (for Netscape) or Address (for IE) field and press

ENTER. For example: http://192.168.0.1

After the connection is established, you will see the web user interface of this product. There are two

appearances of web user interface: for general users and for system administrator.

To log in as an administrator, enter the system password (the default password is password) in the

System Password field and click on the Log in button. If the password is correct, the web appearance

will be changed into administrator configure mode. As listed in its main menu, there are several

options for system administration.

The user can setup step by step to finish the connection with Wizard.

7


16/86


17/86


18/86

Basic Setting

Please Select Advanced Setup to Setup

Primary Setup WAN Type, Virtual Computers

10


19/86

Press Change


20/86

This option is primary to enable this product to work properly. The setting items and the web

appearance depend on the WAN type. Choose correct WAN type before you start.

1. LAN IP Address: the local IP address of this device. The computers on your network mustuse the LAN IP address of your product as their Default Gateway. You can change it if necessary.

2. WAN Type: WAN connection type of your ISP. You can click Change button to choose a

correct one from the following four options:

A. Static IP Address: ISP assigns you a static IP address.

B. Dynamic IP Address: Obtain an IP address from ISP automatically.

C. Dynamic IP Address with Road Runner Session Management. (e.g. Telstra BigPond)

D. PPP over Ethernet: Some ISPs require the use of PPPoE to connect to their services.

E. PPTP: Some ISPs require the use of PPTP to connect to their services.

F. L2TP: Some ISPs require the use of L2TP to connect to their services

Static IP Address

WAN IP Address, Subnet Mask, Gateway, Primary and Secondary DNS: enter the proper setting

provided by your ISP.

12


21/86


22/86

1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned

to you.

2. Server IP Address: the IP address of the PPTP server.

3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't

want to change the password, keep it empty.

3. Connection ID: optional. Input the connection ID if your ISP requires it.

4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or

enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect

to ISP automatically, after system is restarted or connection is dropped.

5. Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect (Always-on):The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the Status

page.

L2TP

First, please check your ISP assigned and Select Static IP Address or Dynamic IP Address.

For example: Use Static1. My IP Address and My Subnet Mask: the private IP address and subnet mask your ISP assigned

to you.

2. Server IP Address: the IP address of the PPTP server.

3. PPTP Account and Password: the account and password your ISP assigned to you. If you don't

want to change the password, keep it empty.

3. Connection ID: optional. Input the connection ID if your ISP requires it.

4. Maximum Idle Time: the time of no activity to disconnect your PPTP session. Set it to zero or

enable Auto-reconnect to disable this feature. If Auto-reconnect is enabled, this product will connect

to ISP automatically, after system is restarted or connection is dropped.

6. Connection Control: There are 3 modes to select:

Connect-on-demand: The device will link up with ISP when the clients send outgoing packets.

Auto-Reconnect (Always-on): The device will link with ISP until the connection is established.

Manually: The device will not make the link until someone clicks the connect-button in the Status-

page.

14


23/86

Virtual Computers (Only for Static and dynamic IP address Wan type)

Virtual Computer enables you to use the original NAT feature, and allows you to setup the one-to-one

mapping of multiple global IP address and local IP address.

Global IP: Enter the global IP address assigned by your ISP.

Local IP: Enter the local IP address of your LAN PC corresponding to the global IP address.

Enable: Check this item to enable the Virtual Computer feature.


24/86

DHCP Server

Press More>>

1. DHCP Server: Choose Disable or Enable.

2. Lease time: This is the length of time that the client may use the IP address it has been assigned

by DHCP server.

3. IP pool starting Address/ IP pool starting Address: Whenever there is a request, the DHCP server

will automatically allocate an unused IP address from the IP address pool to the requesting computer.

You must specify the starting and ending address of the IP address pool.

4. Domain Name: Optional, this information will be passed to the client.

5. Primary DNS/Secondary DNS: This feature allows you to assign DNS Servers

6. Primary WINS/Secondary WINS: This feature allows you to assign WINS Servers

7. Gateway: The Gateway Address would be the IP address of an alternate Gateway.

This function enables you to assign another gateway to your PC, when DHCP server offers an IP to

your PC.

16


25/86


26/86

Security: Select the data privacy algorithm you want. Enabling the security can protect your data

while it is transferred from one station to another.

There are several security types to use:

WEP:

When you enable the 128 or 64 bit WEP key security, please select one WEP key to be used and

input 26 or 10 hexadecimal (0, 1, 2 8, 9, A, B F) digits.

802.1X

Check Box was used to switch the function of the 802.1X. When the 802.1X function is enabled, the

Wireless user must authenticate to this router first to use the Network service.

RADIUS Server

IP address or the 802.1X servers domain-name.

RADIUS Shared Key

Key value shared by the RADIUS server and this router. This key value is consistent with the key

value in the RADIUS server.

18


27/86

WPA-PSK

1. Select Encryption and Pre-share Key Mode

If you select HEX, you have to fill in 64 hexadecimal (0, 1, 2 8, 9, A, B F) digits

If user selects ASCII, the length of pre-share key is from 8 to 63.

2. Fill in the key, Ex 12345678


28/86

WPA

Check Box was used to switch the function of the WPA. When the WPA function is enabled, the

Wireless user must authenticate to this router first to use the Network service. RADIUS Server


Select Encryption and RADIUS Shared Key


If user elects ASCII, the length of pre-share key is from 8 to 63.



WPA2-PSK (AES)

1. Select Pre-share Key Mode


If user selects ASCII, the length of Pre-share key is from 8 to 63.


20


29/86

WPA2 (AES)




Select RADIUS Shared KeyIf you select HEX, you have to fill in 64 hexadecimal (0, 1, 2 8, 9, A, B F) digits




WPA-PSK /WPA2-PSK

The router will detect automatically which Security type the client uses to encrypt.

1. Select Pre-share Key Mode





30/86

WPA/WPA2



The router will detect automatically which Security type(Wpa-psk version 1 or 2) the client uses to

encrypt.


Select RADIUS Shared Key





WPS (WiFi Protection Setup)

WPS is WiFi Protection Setup which is similar to WCN-NET and offers safe and easy way in

Wireless Connection.

22


31/86

WDS (Wireless Distribution System)

WDS operation as defined by the IEEE802.11 standard has been made available. Using WDS it is

possible to wirelessly connect Access Points, and in doing so extend a wired infrastructure to

locations where cabling is not possible or inefficient to implement.


32/86

24


33/86

Change Password

You can change Password here. We strongly recommend you to change the system password for

security reason.


34/86

Forwarding Rules

26


35/86

Virtual Server

This products NAT firewall filters out unrecognized packets to protect your Intranet, so all hosts

behind this product are invisible to the outside world. If you wish, you can make some of them

accessible by enabling the Virtual Server Mapping.

A virtual server is defined as a Service Port, and all requests to this port will be redirected to the

computer specified by the Server IP. Virtual Server can work with Scheduling Rules, and give user

more flexibility on Access control. For Detail, please refer to Scheduling Rule.

For example, if you have an FTP server (port 21) at 192.168.0.2, a Web server (port 80) at

192.168.0.3, and a VPN server at 192.168.0.6, then you need to specify the following virtual server

mapping table:

Service Port Server IP Enable

21 192.168.0.2 V80 192.168.0.3 V

1723 192.168.0.6 V


36/86

Special AP

Some applications require multiple connections, like Internet games, Video conferencing, Internet

telephony, etc. Because of the firewall function, these applications cannot work with a pure NAT

router. The Special Applications feature allows some of these applications to work with this product. If

the mechanism of Special Applications fails to make an application work, try setting your computer as

the DMZ host instead.

1. Trigger: the outbound port number issued by the application..

2. Incoming Ports: when the trigger packet is detected, the inbound packets sent to the specified port

numbers are allowed to pass through the firewall.

This product provides some predefined settings Select your application and click Copy to to add the

predefined setting to your list.

Note! At any given time, only one PC can use each Special Application tunnel.

28


37/86

Miscellaneous Items

IP Address of DMZ Host

DMZ (Demilitarized Zone) Host is a host without the protection of firewall. It allows a computer to be

exposed to unrestricted 2-way communication for Internet games, Video conferencing, Internet

telephony and other special applications.

NOTE: This feature should be used only when needed.

Non-standard FTP port

You have to configure this item if you want to access an FTP server whose port number is not 21.

This setting will be lost after rebooting.

Xbox Support

The Xbox is a video game console produced by Microsoft Corporation. Please enable this function

when you play games.

UpnP Setting


38/86


39/86

Packet Filter

Packet Filter enables you to control what packets are allowed to pass the router. Outbound filter

applies on all outbound packets. However, Inbound filter applies on packets that destined to Virtual

Servers or DMZ host only. You can select one of the two filtering policies:

1. Allow all to pass except those match the specified rules

2. Deny all to pass except those match the specified rules

You can specify 8 rules for each direction: inbound or outbound. For each rule, you can define the

following:

Source IP address

Source port address

Destination IP address

Destination port address

Protocol: TCP or UDP or both.

Use Rule#


40/86

For source or destination IP address, you can define a single IP address (4.3.2.1) or a range of IP

addresses (4.3.2.1-4.3.2.254). An empty implies all IP addresses.

For source or destination port, you can define a single port (80) or a range of ports (1000-1999). Add

prefix "T" or "U" to specify TCP or UDP protocol. For example, T80, U53, U2000-2999. No prefix

indicates both TCP and UDP are defined. An empty implies all port addresses. Packet Filter can

work with Scheduling Rules, and give user more flexibility on Access control. For Detail, please refer

to Scheduling Rule.

Each rule can be enabled or disabled individually.

Inbound Filter:

To enableInbound Packet Filterclick the check box next toEnable in the Inbound Packet Filter

field.

Suppose you have SMTP Server (25), POP Server (110), Web Server (80), FTP Server (21), and

News Server (119) defined in Virtual Server or DMZ Host.

Example 1:

32


41/86

(1.2.3.100-1.2.3.149) they are allow to send mail (port 25), and browse the Internet (port 80)

(1.2.3.10-1.2.3.20) they can do everything (block nothing)

Others are all blocked.

Example 2:

(1.2.3.100-1.2.3.119) they can do everything except read net news (port 119) and transfer files via

FTP (port 21)

Others are all allowed.

After Inbound Packet Filtersetting is configured, click the savebutton.

Outbound Filter:

To enableOutbound Packet Filterclick the check box next toEnable in the Outbound Packet

Filterfield.

Example 1:


42/86

(149.161.123.100-149.161.123.149) they are allowed to send mail (port 25), receive mail (port 110),and browse Internet (port 80); port 53 (DNS) is necessary to resolve the domain name.

(149.161.123.10-149.161.123.20) they can do everything (block nothing)Others are all blocked.

Example 2:

34


43/86


44/86

Domain Filter

Domain Filter

Let you prevent users under this device from accessing specific URLs.

Domain Filter Enable

Check if you want to enable Domain Filter.

Log DNS Query

Check if you want to log the action when someone accesses the specific URLs.

Privilege IP Addresses Range

Setting a group of hosts and privilege these hosts to access network without restriction.

Domain Suffix

A suffix of URL to be restricted. For example, ".com", "xxx.com".

Action

When someone is accessing the URL met the domain-suffix, what kind of action you want. Check

drop to block the access. Check log to log these accesses.

Enable

Check to enable each rule.

36


45/86

Example:

In this example:

1. URL include www.msn.com will be blocked, and the action will be record in log-file.

2. URL include www.sina.com will not be blocked, but the action will be record in log-file.

3. URL include www.google.com will be blocked, but the action will not be record in log-file.

4. IP address X.X.X.1~ X.X.X.20 can access network without restriction.


46/86

URL Blocking

URL Blockingwill block LAN computers to connect to pre-define Websites.

The major difference between Domain filter and URL Blocking is Domain filter require user to input

suffix (like .com or .org, etc), while URL Blocking require user to input a keyword only. In other words,

Domain filter can block specific website, while URL Blocking can block hundreds of websites by

simply a keyword.

URL Blocking Enable

Check if you want to enable URL Blocking.

URL

If any part of the Website's URL matches the pre-defined word, the connection will be blocked. For

example, you can use pre-defined word "sex" to block all websites if their URLs contain pre-defined

word "sex".

Enable

Check to enable each rule.

38


47/86

In this example:

1. URL include msn will be blocked, and the action will be record in log-file.

2. URL include sina will be blocked, but the action will be record in log-file

3. URL include cnnsi will not be blocked, but the action will be record in log-file.

4. URL include espn will be blocked, but the action will be record in log-file


48/86

MAC Address Control

MAC Address Control allows you to assign different access right for different users and to assign a

specific IP address to a certain MAC address.

MAC Address ControlCheck Enable to enable the MAC Address Control. All of the settings in

this page will take effect only when Enable is checked.

Connection controlCheck "Connection control" to enable the controlling of which wired and

wireless clients can connect to this device. If a client is denied to connect to this device, it means the

client can't access to the Internet either. Choose "allow" or "deny" to allow or deny the clients, whoseMAC addresses are not in the "Control table" (please see below), to connect to this device.

Association control Check "Association control" to enable the controlling of which wireless client

can associate to the wireless LAN. If a client is denied to associate to the wireless LAN, it means the

client can't send or receive any data via this device. Choose "allow" or "deny" to allow or deny the

clients, whose MAC addresses are not in the "Control table", to associate to the wireless LAN.

Control table

40


49/86

"Control table" is the table at the bottom of the "MAC Address Control" page. Each row of this table

indicates the MAC address and the expected IP address mapping of a client. There are four columns

in this table:

MACAddress

MAC address indicates a specific client.

Expected IP address of the corresponding client. Keep it empty if you don't care its IP address.IP Address

When "Connection control" is checked, check "C" will allow the corresponding client to connectto this device.

C

When "Association control" is checked, check "A" will allow the corresponding client toassociate to the wireless LAN.

A

In this page, we provide the following Combobox and button to help you to input the MAC address.

You can select a specific client in the DHCP clients Combobox, and then click on the Copy to

button to copy the MAC address of the client you select to the ID selected in the ID Combobox.

Previous page and Next PageTo make this setup page simple and clear, we have divided the

Control table into several pages. You can use these buttons to navigate to different pages.

Example:


50/86

In this scenario, there are three clients listed in the Control Table. Clients 1 and 2 are wireless, and

client 3 is wired.

1. The "MAC Address Control" function is enabled.

2."Connection control" is enabled, and all of the wired and wireless clients not listed in the "Control

table" are "allowed" to connect to this device.

3."Association control" is enabled, and all of the wireless clients not listed in the "Control table" are

"denied" to associate to the wireless LAN.

4. Clients 1 and 3 have fixed IP address either from the DHCP server of this device or manuallyassigned:

ID 1 - "00-12-34-56-78-90" --> 192.168.12.100 ID 3 - "00-98-76-54-32-10" --> 192.168.12.101

Client 2 will obtain its IP address from the IP Address pool specified in the "DHCP Server" page or

can use a manually assigned static IP address.

If, for example, client 3 tries to use an IP address different from the address listed in the Control

table (192.168.12.101), it will be denied to connect to this device.

5. Clients 2 and 3 and other wired clients with a MAC address unspecified in the Control table are all

allowed to connect to this device. But client 1 is denied to connect to this device.

42


51/86

6. Clients 1 and 2 are allowed to associate to the wireless LAN, but a wireless client with a MAC

address not specified in the Control table is denied to associate to the wireless LAN. Client 3 is a

wired client and so is not affected by Association control.

Miscellaneous Items

Remote Administrator Host/Port

In general, only Intranet user can browse the built-in web pages to perform administration task. This

feature enables you to perform administration task from remote host. If this feature is enabled, only

the specified IP address can perform remote administration. If the specified IP address is 0.0.0.0, any

host can connect to this product to perform administration task. You can use subnet mask bits "/nn"

notation to specified a group of trusted IP addresses. For example, "10.1.2.0/24".

When Remote Administration is enabled, the web server port will be shifted to88. You can change web server port to other port, too.


52/86

Administrator Time-out

The time elapses of no activity to logout automatically. Set it to zero to disable this feature.

Discard PING from WAN side

When this feature is enabled, any host on the WAN cannot ping this product.

SPI Mode

When this feature is enabled, the router will record the packet information pass through the router like

IP address, port address, ACK, SEQ number and so on. And the router will check every incoming

packet to detect if this packet is valid.

DoS Attack Detection

When this feature is enabled, the router will detect and log the DoS attack comes from the Internet.

Currently, the router can detect the following DoS attack: SYN Attack, WinNuke, Port Scan, Ping of

Death, Land Attack etc.

Advanced Settings

44


53/86

System Time

Get Date and Time by NTP Protocol

Select it if you want to Get Date and Time by NTP Protocol.

Time Server

Select a NTP time server to consult UTC time

Time Zone

Select a time zone where this device locates.

Set Date and Time manually

Select it if you want to Set Date and Time manually.


54/86

Set Date and Time manually

Select it if you want to Set Date and Time manually.

Function of Buttons

Sync Now:Synchronize system time with network time server

Daylight Saving: Set up where the location is.

System Log

This page support two methods to export system logs to specific destination by means of syslog(UDP)

and SMTP(TCP). The items you have to setup including:

IP Address for Syslog

Host IP of destination where syslogs will be sent to. Check Enableto enable this function.

E-mail Alert Enable

Check if you want to enable Email alert (send syslog via email).

SMTP Server IP and Port

46


55/86

Input the SMTP server IP and port, which are concated with ':'. If you do not specify port number, the

default value is 25. For example, "mail.your_url.com" or "192.168.1.100:26".

Send E-mail alert to

Send e-mail alert to the recipient who will receive these logs. You can assign more than 1 recipientby using ';' or ',' to separate these email addresses.

Dynamic DNS

To host your server on a changing IP address, you have to use dynamic domain name service

(DDNS).

So that anyone wishing to reach your host only needs to know the name of it. Dynamic DNS will map

the name of your host to your current IP address, which changes each time you connect your Internet

service provider.

Before you enable Dynamic DNS, you need to register an account on one of these Dynamic DNS

servers that we list in providerfield.


56/86


57/86

SNMP Setting

In brief, SNMP, the Simple Network Management Protocol, is a protocol designed to give a user the

capability to remotely manage a computer network by polling and setting terminal values and

monitoring network events.

Enable SNMP

You must check either local or remote or both to enable SNMP function. If Local is checked, this

device will response request from LAN. If Remote is checked, this device will response request from

WAN.

Get Community

Setting the community of Get Request your device will response.

Set Community

Setting the community of Set Request your device will accept.

WAN Access IP Address

IF the user wants to limit to specific the IP address to access, please input in the item. The default

0.0.0.0 and means every IP of Internet can get some information of device with SNMP protocol.


58/86

Routing

Routing Tablesallow you to determine which physical interface address to use for outgoing IP data

grams. If you have more than one routers and subnets, you will need to enable routing table to allow

packets to find proper routing path and allow different subnets to communicate with each other.

Routing Table settings are settings used to setup the functions of static.

Dynamic Routing

Routing Information Protocol (RIP) will exchange information about destinations for computing routes

throughout the network. Please select RIPv2 only if you have different subnet in your network.

Otherwise, please select RIPv1 if you need this protocol.

Static Routing: For static routing, you can specify up to 8 routing rules. You can enter the destination

IP address, subnet mask, gateway, and hop for each routing rule, and then enable or disable the rule

by checking or un-checking the Enable checkbox.

Example:

50


59/86

Configuration on NAT Router

Destination SubnetMask Gateway Hop Enabled

192.168.1.0 255.255.255.0 192.168.123.216 1

192.168.0.0 255.255.255.0 192.168.123.103 1

So if, for example, the client3 wanted to send an IP data gram to 192.168.0.2, it would use the above

table to determine that it had to go via 192.168.123.103 (a gateway),

And if it sends Packets to 192.168.1.11 will go via 192.168.123.216Each rule can be enabled or disabled individually.

After routing tablesetting is configured, click the savebutton.


60/86


61/86

Schedule Enable

Selected if you want to Enable the Scheduler press Edit

To edit the schedule rule, press Delete

To delete the schedule rule and the rule #of the rules behind the deleted one will decrease one

automatically.

Schedule Rule can be applied to Virtual server and Packet Filter.


62/86

Qos Rule

Local IP:

Please input Client IP, Example: 192.168.12.33.

Remote Priority:

Please input Global IP and port, Example: 168.96.2.3 and port 21

54


63/86

Toolbox

System Log

Firmware Upgrade

You can upgrade firmware by clicking Firmware Upgrade button.

Backup Setting

You can backup your settings by clicking the Backup Setting button and save it as a bin file. Once

you want to restore these settings, please click Firmware Upgradebutton and use the bin file you


64/86


65/86

Appendix A 802.1x Setting

Figure 1: Testing Environment (Use Windows 2000 Radius Server)

Equipment Details

PC1: Microsoft Windows XP Professional without Service Pack 1 and LevelOne Wireless PCI Card

PC2: Microsoft Windows XP Professional with Service Pack 1a or latter and LevelOne Wireless PCI

Card.

Authentication Server: Windows 2000 RADIUS server with ServicePack 3 and HotFix Q313664.

Note. Windows 2000 RADIUS server only supports PEAP after upgrade to

service pack 3 and HotFix Q313664 (You can get more information from

http://support.microsoft.com/default.aspx?scid=kb; en-us;313664)

DUT Configuration:

1. Enable DHCP server.

2. WAN setting: static IP address.

3. LAN IP address: 192.168.123.254/24.

4. Set RADIUS server IP.

5. Set RADIUS server shared key.

6. Configure WEP key and 802.1X setting.
http://support.microsoft.com/default.aspx?scid=kb;%20en-us;313664http://support.microsoft.com/default.aspx?scid=kb;%20en-us;313664


66/86

The following test will use the inbuilt 802.1X authentication method such as ,EAP_TLS,

PEAP_CHAPv2(Windows XP with SP1 only), and PEAP_TLS(Windows XP with SP1 only) using the

Smart Card or other Certificate of the Windows XP Professional.

DUT and Windows 2000 Radius Server Setup

Setup Windows 2000 RADIUS Server

We have to change authentication method to MD5_Challenge or using smart card or other certificate

on RADIUS server according to the test condition.

Setup DUT

1. Enable the 802.1X (check the Enable checkbox).

2. Enter the RADIUS server IP.

3. Enter the shared key. (The key shared by the RADIUS server and DUT).

4. We will change 802.1X encryption key length to fit the variable test condition.

Setup Network adapter on PC

1. Choose the IEEE802.1X as the authentication method. (Fig 2)

2. Choose MD5-Challenge or Smart Card or other Certificate as the EAP type.

3. If choosing use smart card or the certificate as the EAP type, we select to use a certificate on this

computer.

4. We will change EAP type to fit the variable test condition.

Figure 2 is a setting picture of Windows XP without service pack 1. If users

upgrade to service pack 1, then they cant see MD5-Challenge from EAP typelist any more, but they will get a new Protected EAP (PEAP) option.

58


67/86

Figure 2: Enable IEEE 802.1X access control / Smart card or certificate properties

Windows 2000 RADIUS server Authentication testing:

DUT authenticate PC1 using certificate. (PC2 follows the same test procedures.)

1. Download and install the certificate on PC1. (Fig 4)

2. PC1 chooses the SSID of DUT as the Access Point.

3. Set authentication type of wireless client and RADIUS server both to EAP_TLS.

4. Disable the wireless connection and enable again.

5. The DUT will send the user's certificate to the RADIUS server, and then send the message ofauthentication result to PC1. (Fig 5)

6. Windows XP will prompt that the authentication process is success or fail and end theauthentication procedure. ( Fig 6)

7. Terminate the test steps when PC1 get dynamic IP and PING remote host successfully.


68/86

Figure 4: Certificate information on PC1

Figure 5: Authenticating

60


69/86

Figure 6: Authentication success

DUT authenticate PC2 using PEAP-TLS.

1. PC2 chooses the SSID of DUT as the Access Point.

2. Set authentication type of wireless client and RADIUS server both to PEAP_TLS.

3. Disable the wireless connection and enable again.

4. The DUT will send the user's certificate to the RADIUS server, and then send the message of

authentication result to PC2.

5. Windows XP will prompt that the authentication process is success or fail and end the

authentication procedure.

6. Terminate the test steps when PC2 get dynamic IP and PING remote host successfully.

Support Type: The router supports the types of 802.1x Authentication: PEAP-CHAPv2 andPEAP-TLS.

1. PC1 is on Windows XP platform without Service Pack 1.

2. PC2 is on Windows XP platform with Service Pack 1a.

3. PEAP is supported on Windows XP with Service Pack 1 only.

4. Windows XP with Service Pack 1 allows 802.1x authentication only when dataencryption function is enable.


70/86

Appendix B WPA-PSK and WPA

Wireless Router: LAN IP: 192.168.123.254

WAN IP: 192.168.122.216

Radius Server: 192.168.122.1

User A: XP Wireless Card:Ti-11g

Tool: Odyssey Client Manager

Refer to: www.funk.com

Download: http://www.funk.com/News&Events/ody_c_wpa_preview_pn.asp

Or Another Configuration:

WPA-PSK

In fact, it is not necessary for this function to authenticate by Radius Server, the client and wirelessRouter authenticate by them.

62
http://www.funk.com/http://www.funk.com/News&Events/ody_c_wpa_preview_pn.asphttp://www.funk.com/News&Events/ody_c_wpa_preview_pn.asphttp://www.funk.com/News&Events/ody_c_wpa_preview_pn.asphttp://www.funk.com/


71/86

Method1:

1. Go to the Web manager of Wireless Router to configure, like below:

2. Go to Odyssey Client Manager, first choose Network

Before doing that, you should verify if the software can show the wireless card.

Open Adapters

3. Add and edit some settings:


72/86


73/86

2. Then reboot.

3. Setting on the router and client:

Router:

Client:

Go to Network Connection and select wireless adapter.Choose View available Wireless Networks like below:

Advanced choose 123kk

WPA:

For this function, we need the server to authenticate. This function is like 802.1x.


74/86

The above is our environment:

Method 1:

1. The User A or User B have to get certificate from Radius, first.

http://192.168.122.1/certsrv

Account: fae1

Password: fae1

2. Then, Install this certificate and finish.

3. Go to the Web manager of Wireless Router to configure, like below:

66
http://192.168.122.1/certsrvhttp://192.168.122.1/certsrvhttp://192.168.122.1/certsrv


75/86

4. Go to Odyssey Client Manager, choose Profiles and Setup Profile name as 1

Login name and passwd are fae1 and fae1.

Remember that you get certificate from Radius in Step1.

5. Then Choose certificate like above.


76/86


77/86

7. Go Network and Select 1 and ok

8. Back to Connection and Select 123kk.

If successfully, the wireless client has to authenticate with Radius Server, like below:


78/86

9.Result:

Method 2:

1. The UserA or UserB have to get certificate from Radius, first.

http://192.168.122.1/certsrv

Account: fae1

Password: fae1

2. Then Install this certificate and finish.3. Setting on the router and client:Router:

70
http://192.168.122.1/certsrvhttp://192.168.122.1/certsrvhttp://192.168.122.1/certsrv


79/86

Client:

Go to Network Connection and select wireless adapter.

Choose View available Wireless Networks like below:

Advanced choose 123kk

Select WirelessCA and Enable in Trusted root certificate authority:


80/86

Then, if the wireless client wants to associate, it has to request to authenticate.

72


81/86

Appendix C FAQ and Troubleshooting

What can I do when I have some trouble at the first time?

1. Why can I not configure the router even if the cable is plugged in the ports of Router and

the led is also light?

A: First, make sure that which port is plugged. If the cable is in the Wan port, please change to plug

in LAN port 1 or LAN port 4:

Then, please check if the Pc gets ip address from Router. Use command mode as below:

If yes, please execute Browser, like Mozilla and key 192.168.123.254 in address.

If not, please ipconfig /release, then ipconfig /renew.

Whatever I setup, the pc can not get ip. Please check Status Led and refer to the Q2:


82/86

2. Why can I not connect the router even if the cable is plugged in LAN port and the led is light?

A: First, please check Status Led. If the device is normal, the led will blink per second.

If not, please check the blinking Status led shows.

There are many abnormal symptoms as below:

Status Led is bright or dark in work:The system hanged up .Suggest powering off and on therouter. But this symptom often occurs, please reset to default or upgrade latest fw to try again.

Status led flashes irregularly:Maybe the root cause is Flash ROM and please press reset Button to

reset to default or try to use Recovery mode. (Refer to Q3 and Q4)

Status flashes very fast while powering on:Maybe the router is the recovery mode and please

refer to Q4.

3. How to reset to factory default?

A: There are 2 methods to reset to default.

Method 1)Restore with RESET button

First, turn off the router and press the RESET button in. And then, power on the router and push the

RESET button down until the Status start flashing, then remove the finger. If LED flashes about 8

times, the RESTORE process is completed. However, if LED flashes 2 times, repeat steps and try

again.

Method 2)Restore directly when the router power on

First, push the RESET button about 5 seconds (Status will start flashing about 5 times), remove the

finger. The RESTORE process is completed.

4. Why can I not connect Internet even though the cables are plugged in WAN port and LAN

port and the LEDs are blink? In addition, Status led is also normal and I can configure web

management?

A: Make sure that the network cable from DSL or Cable modem is plugged in Wan port of Router and

that the network cable from LAN port of router is plugged in Ethernet adapter. Then, please check

which wan type you use. If you are not sure, please call the ISP. Then please go to this page to input

the information of ISP is assigned.

74


83/86

5. When I use Static IP Address to roam Internet, I can access or ping global IP 202.93.91.218,

But I can not access the site that inputs domain name, for example http://espn.com?

A: Please check the DNS configuration of Static IP Address. Please refer to the information of ISP

and assign one or two in DNS item.

How do I connect router by using wireless?

1. How to start to use wireless?

A:First, make sure that you already installed wireless client device in your computer. Then check the

configuration of wireless router. The default is as below:

About wireless client, you will see wireless icon:
http://espn.com/http://espn.com/


84/86

Then click and will see the AP list that wireless client can be accessed:

If the client can not access your wireless router, please refresh network list again.

Choose the one that you will want to connect and connect:

If successfully, the computer will show

User will also retrieve IP from router:

2. When I use AES encryption of WPA-PSK to connect even if I input the correct pre-share key?

A:First, you must check if the driver of wireless client supports AES encryption. Please refer to the

below:

76


85/86

If SSID is default and click Properties to check if the driver of wireless client supports AES

encryption.

3. When I use wireless to connect the router, but I find the signal is very low even if I am close

to the router?

A:Please check if the wireless client is normal, first. If yes, please send the unit to the seller and

verify what the problem is.


86/86

Technical Specifications

General

Model WBR-6001 N_MaxWireless Broadband Router

Data Transfer Rate 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, 54Mbps

Max physical rate up to 300 Mbps in 802.11n mode

Transmit Power 802.11b: 172dBm

802.11g: 152dBm

802.11n: 142dBm

Frequency RangeAmerica/ FCC: 2.412~2.462GHz (11 Channels)

Europe/ ETSI: 2.412~2.472GHz (13 Channels)

Modulation Schemes DBPSK/DQPSK/CCK/OFDM

Channels 1~11 channels (FCC), 1~13 channels (ETSI),

1~14 channels (MKK-Japan)

Security 64/128-bits WEP Encryption, WPA-PSK, WPA2-PSK, WPA, WPA2, 802.x

Diagnostic LED

Reset

Status

WAN

WLANLAN LEDs

Antenna 1.8dBi dipole antenna * 2

Physical and Environmental

Driver Support Windows 2000, Windows XP, Windows Vista

Temperature Operating: 0~ 40C, Storage: -10~ 70C

Humidity 10% ~ 95% RH, no condensation

levelone wbr-6001 um

Documents