Single Pole (One location) or 3-Way (Multi-location) Scene Capable Incandescent Dimmer

Cat. No. VRI1Ø-1L, 1000W (Lighted) 120VAC, 60Hz

INSTALLATION INSTRUCTIONSDI-000-VRI10-02AWARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualifiedelectrician.• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,donotinstalltocontrolareceptacle,fluorescentlighting,amotor-oratransformer-operatedappliance.• Usewithincandescentor120Vhalogenfixturesonly.• Vizia RF +TMdimmersarenotcompatiblewithstandard3-wayor4-wayswitches.TheymustbeusedwithcompatibleVizia+™orViziaRF+TMremotesformulti-locationdimming.• Useonlyone(1)ViziaRF+™dimmerinamulti-locationcircuitwithupto9coordinatingremotes(withoutLEDs)orupto4matchingremotes(withLEDs).Theremote(s)willturnthe

lightonatthebrightnesslevelselectedatthedimmer.

WARNINGS AND CAUTIONS:• Dimmermaynotoperatewithdiodedlamps(SylvaniaDesigner16™orPhilipsPAR-16™).• Totalminimumloadmustexceed40W.• Dimmermayfeelwarmtothetouchduringnormaloperation.• Recommendedminimumwallboxdepthis2-1/2”.• Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft.• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingfixture.• Usethisdeviceonlywithcopperorcoppercladwire.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

INSTALLING YOUR DIMMER

NOTE: UsecheckboxeswhenStepsarecompleted.√

2

4

Bk

RDYL/RD

1

3

5

Coordinating Remote Dimmer

5

2

1

Black

Green

Red

Yellow/Red

4

3

hot (Black)

Neutral (White)

Load

DimmerCoordinating Remote (no LEDS)

YL/RD

YL/RD

RD

WhRD

BkBkBlack

Do not use forincandescentapplications.

White

Line 120vAC, 60hz

GreenGround

GreenGround

Tools needed to install your Dimmer

Slotted/PhillipsScrewdriver ElectricalTapePliers Pencil Cutters Ruler

3-Way Wiring with Coordinating Remote (no LEDs) Application:

Step 4b

GreenGround

hot (Black)

Neutral (White)

Load

Dimmer

Black

White

Line 120vAC, 60hz

Black

Yellow/Red

Red

InsulatingLabel

Single-Pole Wiring Application:Step 4a

Black

Green

Red

Yellow/Red

Dimmer

Insulating Label:This wire is used in 3-way installationsonly. For single pole installations, donot remove this insulating label.

4

32

1

IMPORTANT: For3-Wayapplications,notethatoneofthescrewterminalsfromtheoldswitchbeingremovedwillusuallybeadifferentcolor(Black)orlabeledCommon.Tagthatwirewithelectricaltapeandidentifyasthecommon(LineorLoad)inboththedimmerwallboxandremotewallbox.

Step 2 Identifying your wiring application (most common): NOTE:Ifthewiringinthewallboxdoesnotresembleanyoftheseconfigurations,consultaqualifiedelectrician.

2

4

3

1 2

4

1

5

3

3-Way1. Line or Load

(See important instruction below)

2. Neutral3. Ground4. FirstTraveler

– note color5. SecondTraveler

– note color

Single-Pole1. Line (Hot) 2. Neutral 3. Ground 4. Load

INTRODUCTION

Leviton’sVizia RF +TMcomponentsaredesignedtocommunicatewitheachotherviaRadioFrequency(RF)toprovideremotecontrolofyourlighting.UsingRFtechnologyallowsLevitontoprovidethegreatestsignalintegritypossible.EachmoduleinLeviton’sVizia RF +TMcomponentlineisaZ-Wave®enableddevice.InaZ-Wave® network,eachdeviceisdesignedtoactasarouter.Theserouterswillre-transmittheRFsignalfromonedevicetoanotheruntiltheintendeddeviceisreached.Thisensuresthatthesignalisreceivedbyitsintendeddevicebyroutingthesignalaroundobstaclesandradiodeadspots.TheSceneCapableIncandescentDimmeriscompatiblewithanyZ-Wave®enablednetwork,regardlessofthemanufacturerandcanalsobeusedwithotherdevicesdisplayingtheZ-Wave® logo. CAUTION:RemembertoexercisegoodcommonsensewhenusingtheTimerfeaturesofyourremote,especiallywhenschedulingunattendeddevices.Therecanbesomeunexpectedconsequencesifnotusedwithcare.Forexample,anemptycoffeepotcanberemotelyturnedon.Ifthatshouldhappen,yourcoffeepotcouldbedamagedfromoverheating.Ifanelectricheateristurnedonbyremotecontrolwhileclothingisdrapedoverit,afirecouldresult.DO NOT USEtheremoteforthecontrolofhighpowerheatingappliancessuchasportableheaters.Thisdevicewillnotcontrollightingthatisusedwithelectroniclow-voltageandhighfrequencypowersupplytransformers,norhighpressuredischargelamps(HIDlighting).Thisincludesmercury-vapor,sodiumvaporandmetalhalidelamps.

• SoftfadeON/OFF• Scenecapable• Twowaycommunication• RFreliability• NoNeutralwirerequired

FEATURES

• ON/OFFLEDandBrightnesslevelLED

• Easeofinstallation–Nonewwiring

• CompatiblewithotherZ-Wave® enableddevices

Changing the color of your Dimmer:Yourdevicemayincludecoloroptions.Tochangecoloroftheface,proceedasfollows:

Line up tabs and press in sides one at a time to attach

Push in side at tab to release

Installing Dimmer by itself or with other devices

IfinstallingDimmerinasingledeviceapplication,proceedwiththeINSTALLING YOUR DIMMERsection.IfinstallingDimmerinamulti-deviceapplication,proceedasfollows:

MULTI-DEvICE APPLICATION:Inmulti-dimmerinstallations,thereductionofthedimmer’scapacityisrequired.Refertothechartformaximumloadperdimmer.

MAXIMUM LOAD PER DIMMER FOR MULTI-DEvICECat. No.

VRI1Ø 1000W

Single

800W

Two Devices

650W

More than 2 Devices hot (Black)

Neutral (White)

Load

DimmerMatching Dimmer

Remote (with LEDs)

YL/RD

RedWh Bk

Black

Black

White

Yellow/Red

Line 120vAC, 60hz

GreenGround

GreenGround

AdditionalNeutral Wire

Bk

RDYL/RD

Matching Dimmer Remote

4

3

1

2

5

Dimmer

Black

Green

Red

5

2

1

Yellow/Red

4

3

Step 4c 3-Way Wiring with Matching Remote (w/LEDs) Application:

Strip Gage (measure bare wire

here or use gage on back of the dimmer)

5/8”(1.6 cm)cut

(if necessary)

Step 3 Preparing and connecting wires:

• Makesurethattheendsofthewiresfromthewall boxarestraight (cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.• For Single Pole Application, go to Step 4a.• For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.• For 3-Way Matching Remote (with LEDs) Application, go to Step 4c.

NOTE: ThedimmermustbeinstalledinawallboxthathasaLoadconnection.ThematchingremotemustbeinstalledinawallboxwithaLineHotconnectionandaNeutralconnection.ANeutralwiretothematchingremoteneedstobeaddedasshown.Ifyouareunsureaboutanypartoftheseinstructions,consultaqualifiedelectrician.NOTE:Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft.WIRING MATChING REMOTE (wall box with Line hot connection):Connect wires per WIRING DIAGRAM as follows:• GreenorbarecopperwireinwallboxtoGreenterminalscrew.• LineHot(common)wallboxwireidentified(tagged)whenremoving

oldswitchandFirstTravelertoremoteterminalscrewmarked“BK”.• SecondTravelerwallboxwirefromdimmertoremoteterminal

screwmarked“YL/RD”(note wire color).Thistravelerfromtheremotemustgototheterminalscrewonthedimmer marked“YL/RD”.

• LineNeutralwallboxtoremoteterminalscrewmarked“WH”.WIRING DIMMER (wall box with Load connection):Connect wires per WIRING DIAGRAM as follows:• GreenorbarecopperwireinwallboxtoGreendimmerlead.• Loadwallboxwireidentified(tagged)whenremovingoldswitchto

Reddimmerlead.• FirstTravelerLineHottoBlackdimmerlead.• RemoveRedinsulatinglabelfromYellow/Reddimmerlead.• SecondTravelerwallboxwire(note color as above)toYellow/Red

dimmerlead.Thistravelerfromthedimmermustgototheterminalscrewontheremotemarked“YL/RD”.

• ProceedtoStep5.

Step 1 WARNING: TO AvOID FIRE, ShOCk, OR DEATh; TURN OFF POWER atcircuitbreakerorfuseandtestthatpowerisoffbeforewiring!

Remove all inner side sections

Do not remove outer side sections

WIRE NUT / # OF CONDUCTOR COMBINATION ChART

1-#12w/1to3#14,#16or#18 2-#12w/1or2#16or#181-#14w/1to4#16or#182-#14w/1to3#16or#18

For non-standard wiring applications, refer to Wire Nut and Conductor Size Chart

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:• GreenorbarecopperwireinwallboxtoGreendimmerlead.• LineHotwallboxwiretoBlackdimmerlead.• LoadwallboxwiretoReddimmerlead.• Yellow/ReddimmerleadshouldhaveRedinsulationlabelaffixed. NOTE:IfinsulatinglabelisnotaffixedtoYellow/Reddimmerlead,

useelectricaltapetocover.• Proceed to Step 5.

WIRING DIMMER:Connect wires per WIRING DIAGRAM as follows:NOTE:WhenusingthecoordinatingremotewithoutLEDs,thedimmercanbeinstalledoneithertheLineorLoadsideofthe3-waycircuit.NOTE: Maximumwirelengthfromdimmertoallinstalledremotescannot exceed300ft.• GreenorbarecopperwireinwallboxtoGreendimmerlead.• LineHot(common)wallboxwireidentified(tagged)whenremovingoldswitch

toBlackdimmerlead.• FirstTravelerwallboxwiretoReddimmerlead(note wire color).Thistraveler

fromthedimmermustgototheterminalscrewontheremotemarked“RD”.• RemoveRedinsulatinglabelfromYellow/Reddimmerlead.• SecondTravelerwallboxwiretoYellow/Reddimmerlead(note wire color).

Thistravelerfromthedimmermustgototheterminalscrewontheremotemarked“YL/RD”.

WIRING COORDINATING REMOTE:Connect wires per WIRING DIAGRAM as follows:NOTE: Maximumwirelengthfromdimmertolastremoteis300ft.• GreenorbarecopperwireinwallboxtoGreenterminalscrew.• Loadwallboxwireidentified(tagged)whenremovingoldswitchtoterminal

screwmarked“BK”.• FirstTravelerwallboxwire(note color as above)toterminalscrewmarked

“RD”.ThistravelerfromtheremotemustgototheReddimmerlead.• SecondTravelerwallboxwire(note color as above)toterminalscrew

marked“YL/RD”.ThistravelerfromtheremotemustgototheYellow/Reddimmerlead.

• Remoteterminalscrewmarked“WH”shouldhaveWhiteinsulationlabelaffixed.NOTE: Ifinsulatinglabelisnotaffixedtoterminalscrewmarked“WH”,useelectricaltapetocover.

• ProceedtoStep5.

Including Scene Capable Dimmer into Z-Wave® Network:

Restore Power: Restorepoweratcircuitbreakeror fuse.Installation is complete.

D)ThePrimaryProgrammer/ControllerwillassignanodeIDnumber(Name)forthismodule.

NOTE: ThisIDnumber(Name)willbestoredinthecontrollerlibrarytobeusedforfuturereference.

NOTE: Youmayeditthenameofthisdeviceatthistime.

E) The dimmer is now installed in the network.

NOTE: IfadimmerhasbeensuccessfullyIncludedinthenetworkandtheusertriestoIncludeitagainwithoutfirstexcludingitfromthenetwork,themodulewillretainthefirstnodeIDithadreceivedandignorethesecond.

Testing your Dimmer prior to mounting in wall box:

LIMITED 5 YEAR WARRANTY AND EXCLUSIONSLevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenefitofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforfiveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchfiveyearperiodtheproductisreturnedprepaid,withproofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandfitnessforaparticularpurpose,islimitedtofiveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

• Restorepoweratcircuitbreakerorfuse.• PresspaduntillocatorlightisOFF.Lights

shouldturnON.IflightsdonotturnON,presstherighthalfofDIM/BRIGHTbaruntilthelightsbrighten.

If lights still do not turn ON, refer to the TROUBLEShOOTING section.

NOTES:• Ifusinganon-LevitonProgrammer/Controller,

refertotheProgrammer/ControllerinstructionsheetforIncludingadevice.

• IfusingtheVRCPG'sInstallChecklistfeature,godirectlytoStepB.

A)IfusingaLevitonZ-Wave®Programmer/Controller,Cat.No.VRCPG,presstheMenubuttonandscrolldowntoSystemSetup.PressthecenterbuttontoselectSystemSetupMenu.ChooseAdvancedSettings.PressthecenterbuttontoselectNetwork.

B)Whilestandingclosetothemodule(approx.2-5ft),pressthecenterbuttonto<Include>deviceinthenetwork.

NOTE:Onlyonedevicemaybeincludedatatime.DO NOTputmultipledevicesintotheInclusionmodeatanytime.

C) WhiletheProgrammer/ControllerisintheInclusionmodeandtheLocatorLEDisONonthedimmer,pushthepushpadtoturnONthedimmer.TheProgrammer/ControllerwillverifyinclusionandthelocatorLEDwillturnOFFonthedimmer.

IfthedimmerisflashingAmberwhileintheInclusionmode,theProgrammer/Controllerisstilltryingtocommunicatewiththedimmer.Waituntilthedevicestopsflashing,thenpresspushpad.

NOTE:IfthelocatorLEDonthedimmerturnssolidRedwhileincluding,therehasbeenacommunicationerror.RefertoTroubleshootingsection. DI-000-VRI10-02A2008©LevitonMfg.Co.,Inc.

ProtectedunderU.S.PatentNumber6,388,399andpatentspending andlicensedunderU.S.PatentsNumbers5,905,442,and5,982,103

Programmer/Controller Cat. No. vRCPG

Menu Button

1 ON

2 ON

3 ON

4 ON

OFF

OFF

OFF

OFF

Center Button

• Lights Flickering - Lamphasabadconnection. - Wiresnotsecuredfirmlyunderterminalscrewsofdimmer

and/orremote. - Localswitch,ON• Light does not turn ON and Locator LED does not turn ON - Circuitbreakerorfusehastripped. - Lampisburnedout. - LampNeutralconnectionisnotwired. - Confirmthatthedeviceisbeingsuppliedfroma120V,60HzAC

sourceONLY. - Confirmthatunitisprogrammedproperly.Repeat“TOINSTALL”

sectiontoverifythatithasbeenincludedintheZ-Wave™network.

• Intermittent dimmer operation - Minimumloadisunder40W. - ConfirmthattheLoadbeingcontrolleddoesnotexceedthe

1000Wdimmerlimit.• Remote does not operate lights - Ensurethattotalwirelengthdoesnotexceed300ft.

TROUBLEShOOTING

For additional information, contact Leviton’s Techline at 1-800-824-3005 or visit Leviton’s website at

www.viziaRFplus.com

NOTE:ThelocatorlightwillilluminatewhentheloadisintheOFFpositiontofacilitateaccessinthedark.NOTE:Ifusingthedimmerina3-wayapplication,thelightswillturnONatbrightnesssetondimmer’sDIM/BRIGHTbar.Thelightingcanbecontrolledfromeitherthedimmerortheremotelocation.Push Pad (Default settings) Turn ON from OFF position: Tap–LightsturnONtopresetlevel. PressandHold–LightsturnONtofullbright.Turn OFF from ON position:Tap–LightsturnOFF.

LED Brightness Display

DIM/BRIGhT Bar

Push Pad

Locator Light

OPERATION

Installationmaynowbecompletedbytighteningmountingscrewsintowallbox.Attachwallplate.

Dimmer Mounting: TURN OFF POWER AT CIRCUIT BREAkER OR FUSE.

Step 7

Step 6

NOTE: ItisveryimportanttoaccuratelyExcludedevicesfromthenetworkwhenmovingorremovingadevicefromaZ-Wave®network.ThisensuresthatallinformationhasbeenremovedfromyourPrimaryProgrammer/Controller’sinformationtableandisnotcountedontobeapartofthemeshnetwork.A)IfusingaLevitonZ-Wave®Programmer/Controller,Cat.No.VRCPG,

presstheMenubuttonandscrolldowntoSystemSetup.PressthecenterbuttontoselectSystemSetupMenu.ChooseAdvancedSettings.PressthecenterbuttontoselectNetwork.

B) Whilestandingclosetothedimmer,pressthecenterbuttonto<Exclude>devicefromthenetwork.WhiletheProgrammer/ControllerisintheExclusionmodeandthelocatorLEDisONonthedimmer,pressthepushpadonthedimmer.TheProgrammer/ControllerwillverifyExclusionandthelocatorLEDwillturnOFFonthedimmer.

IfthedimmerisflashingAmberwhileintheExlusionmode,theProgrammer/Controllerisstilltryingtocommunicatewiththedimmer.Waituntilthedevicestopsflashing,thenpressthepushpad.

Factory Default:Ifyourdimmerisnotresponding,oryouareunabletocontrolitafteryouhavetriedtoInclude/Excludeitmultipletimes,itmaybenecessarytoresetthedimmertoitsoriginalfactorysettings.Toaccomplishthis,proceedasfollows:• Onthedimmer,engageheair-gapswitch(refer to Operation

section)andwait5seconds.PresspushpadbackintoframeandholdpushpaduntilthelocatorLEDturnsAmberandthenturnsRed.Thedimmerisnowreset.Oncethedimmerisreset,itwillbenecessarytoRe-Includeittoanetworkbeforeitcanbeused.

CAUTION:SETTINGADEVICETOAFACTORYDEFAULTDOESNOTEXCLUDETHATDEVICEFROMANETWORK.THEEXCLUSIONPROCEDUREMUSTSTILLBEFOLLOWEDTOREMOVETHEDEVICEFROMTHEPRIMARYCONTROLLER’SINFORMATIONTABLE.FAILURETODOSOMAYRESULTINASYSTEMTHATISSLOWTORESPOND,ORMAYFAILTORESPONDTOSOMEDEVICES.

Step 9 Excluding Dimmer from Network:

Step 8

NOTE: Dresswireswithabendasshownindiagraminordertorelievestresswhenmountingdevice.

• Positionallwirestoprovideroominoutletwallboxfordevice.

• Ensurethattheword“TOP”isfacingupondevicestrap.

• Partiallyscrewinmountingscrewsinwallboxmountingholes.

Step 5

A-2) TheLocatorLEDwillblink2timespersecondtoindicatethedeviceisinProgramModeA-2, Minimum Brightness Level. TochangetheMinimum Brightness Levelfrom1-50%,usetheDIM/BRIGHTBar.Thelightoutputwillreflecttheminimumbrightnesslevelselected.BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewilladvancetothenextprogrammingmode,A-3.

A-3) TheLocatorLEDwillblink3timespersecondtoindicateProgramMode A-3, Preset ON Level.TochangethecurrentPreset ON Levelfrom1-100%,usetheDIM/BRIGHTBar.Ifthisfeatureisnotdesired,pressandholdthelefthalfoftheDIM/BRIGHTBar(v) untilnoLEDislit(defaultsetting).BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewillexitProgrammingModeA.

Program Mode BTo enter Program Mode B:PressandholdthePushPadandthenthelefthalfofthe DIM/BRIGHTBar(v)for5secondsuntiltheLocatorLEDandrightmostLED(LED7)begintoblink.B-1) UponreleasingthePushPadandthelefthalfofthe

DIM/BRIGHTBar(v),theLocatorLEDwillcontinuetoblinkoncepersecondindicatinghedimmerisinProgramModeB-1, ON Fade Rate.TochangetheON Fade Rate,usetheDIM/BRIGHTBartomovetheLEDtothedesiredpresetlevelaccordingtoChart B.BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewilladvancetothenextprogrammingmode,B-2.

B-2) TheLocatorLEDwillblink2timespersecondtoindicateProgramMode B-2, OFF Fade Rate.TochangetheOFF Fade Rate,usetheDIM/BRIGHTBartomovetheLEDtothedesiredpresetlevelaccording to Chart B.BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewilladvancetothenextprogrammingmode,B-3.

LED BrightnessDisplay

1 2 3 4 5 6 7

Definition of A ModesA-1) EnergySave:Setsthemaximumbrightnesslevelforenergy

savings.A-2) MinimumBrightnessLevel:Setstheminimumdimminglevel.A-3) PresetONLevel:Setstheturnonbrightnesslevelregardlessof

theprevioussetlightlevel(formerlyDimLock).Definition of B ModesB-1) ONFadeRate:Setstheamountoftimeinsecondsittakesthe

lightstoturnONtomaximumbrightness.B-2) OFFFadeRate:Setstheamountoftimeinsecondsittakesthe

lightstoturnOFFfrommaximumbrightness.B-3) LEDOptions:SetsthetimeperiodinsecondstheLocatorLED

andBrightnessdisplaywillstayonbeforeextinguishing.

Definition of LEDsLeftmostLED=LED1RightmostLED=LED7NOTES:• Thedevicewillexitprogramming

modeafter3minutesofinactivity.• Pressingthepushpadatanytime

duringprogrammingwilladvancethedevicetothenextprogrammingmode.

ADvANCED PROGRAMMING FEATURES

Program Mode ATo enter Program Mode A:PressandholdthePushPadandthentherighthalfofthe DIM/BRIGHTBar(^)for5secondsuntiltheLocatorLEDandleftmostLED(LED1)begintoblink.A-1) UponreleasingthePushPadandtherighthalfofthe

DIM/BRIGHTBar(^),theLocatorLEDwillcontinuetoblinkoncepersecondandtherightmostLEDwillilluminatetodisplaythedeviceisinProgramModeA-1, Energy Save.Thedefaultenergysavemodeis100%i.e.fullbright.Tochangethe Energy Savelevel,usetheDIM/BRIGHTBartomovethecorrespondingLEDtothedesireddiscretepresetlevelaccording to Chart A.BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewilladvancetothenextprogrammingmode,A-2.

B-3) TheLocatorLEDwillblink3timespersecondtoindicateProgramMode B-3, LED Options.TochangetheLED Optionssettings,usetheDIM/BRIGHTBartomovetheLEDtothedesiredpresetsettingaccordingtotheChart B-3.BytappingthePushPadthissettingwillautomaticallybesavedandthedevicewillexitProgrammingModeB.

LED

LED 1

LED 2 (Default)

LED 3

LED 4

LED 5

LED 6

LED 7

FADE ON

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

FADE OFF

Chart B

When indicatorlight is at LED #

7654321

Light output is at

100%97%95%90%85%80%75%

Energy consumptionsavings amounts to

0%5%8%

11%14%17%20%

Chart A Chart B-3

LED

LED 1

LED 2

LED 3

LED 4

LED 5

LED 6

LED 7

LOCATOR LED TIMEOUT

Active

Active

Active

Active

Turns off 5 sec. after use

Turns off 5 sec. after use

Turns off 5 sec. after use

LED BRIGHTNESS DISPLAY OPTIONS

Active

Turns off 5 sec. after use

Active

Turns off 5 sec. after use

LED Bar active

LED Bar turns off 5 sec. after use

LED Bar turns off 5 sec. after use

vRCPG Programmer/

Controller

NOTE: Remotemustbeincloseproximitytodimmerwhenincludinginnetwork.

DIM/BRIGhT Bar BRIGhTEN:PressrighthalfofDIM/BRIGHTBar–Lightsbrightentodesiredlevel.DIM:PresslefthalfofDIM/BRIGHTBar–Lightsdimtodesiredlevel. IfyoucontinuetoholdthelowerhalfoftheDIM/BRIGHTBar,thelightswillDIMtominimumlevelandthenturnOFF. NOTE:WhenlightsareOFFyoucanchangethelightlevelthatthelightswillturnONtousingtheDIM/BRIGHTBar.Ifthereisapoweroutage,whenthepowerisrestoredthelightswillreturntothelastsettingbeforethepowerinterruption.Air-Gap Switch:Onthedimmeronly,engage theair-gapswitchbygentlypressingthetopofthepushpaduntilthebottomliftscompletelyoutoftheframeandaclickisheard (refer to Figure).LEDswillturnOFF. Thiswillcutpowertothefixturetoreplacethebulb.Afterservicingiscomplete,pushthepushpadbackfornormaloperation.Cleaning: Cleanwithadampcloth.DO NOT usechemicalcleaners.

Gently press top of push pad

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBDigitalDevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,whichcanbedeterminedbyturningtheequipmentOFFandON,theuserisencouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:• ReorientorrelocatethereceivingAntenna.• Increasetheseparationbetweentheequipmentandthe

receiver.• Connecttheequipmentintoanoutletonacircuitdifferentfrom

thattowhichthereceiverisconnected.• Consultthedealeroranexperiencedradio/tvtechnicianfor

help.

FCC COMPLIANCE STATEMENT