lg l194wtx-bf 19" 5ms widescreen lcd...
TRANSCRIPT
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
L194WTL204WT
L194WTML204WTML194WTQL204WTQL194WTXL204WTX
User’s Guide
A1
This unit has been engineered and manufactured to ensure your personalsafety, however improper use may result in potential eletrical shock or firehazards. In order to allow the proper operation of all safeguardsincorporated in this display, observe the following basic rules for itsinstallation, use, and servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that thesocket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications ofthis manual or listed on the display. If you are not sure what type of power supplyyou have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call your servicetechnician for replacement.
Do not Open the Display.There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.During a lightning storm or when the display is to be left unattended for anextended period of time, unplug it from the wall outlet.
Important Precautions
A2
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not placethe display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchensink, laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may causesome afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.
On Disposal
The fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
A3
Connecting the speaker
1. Place the monitor with its front facing downward on a soft cloth.
2. nsert the protruding hook of the speaker in the direction of the slot in the back of the product.
Connecting the speakers - The feature is only for speaker models - L194WTM, L204WTM
DC-OUT D-SUB DVI-DAC-IN DC-OUT D-SUB DVI-D AC-IN
DC-OUT D-SUB DVI-DAC-IN DC-OUT D-SUB DVI-D AC-IN
Hook
Slot
Audio DC-InCable
3. After setting up the speaker, connect the Audio DC-In Cable to the back of the product.
DC-OUT D-SUB DVI-DAC-IN DC-OUT D-SUB DVI-D AC-INDC-OUT D-SUB DVI-DAC-IN DC-OUT D-SUB DVI-D AC-IN
19 inch monitor 20.1 inch monitor
A4
Connecting the Display
ImportantThis illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Once you connect the stand base, try not to disconnect it.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot.
Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.
Connecting the stand
1. Place the monitor with its front facing downward on a soft cloth.
2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”.
3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction.
4. Once assembled take the monitor up carefully and face the front side
REAR
REAR
REAR
REAR
FRONT
FRONT
Connecting the Display
A5
1. Put a cushion or soft cloth on a flat surface.
To remove the Stand: 2. Place the monitor face down on
the cushion or soft cloth.
3. Hold the product as it follows and lift up the Stand slightly.
4. Change your hold on the product as it follows and turn the Stand Base in the arrowdirection.
5. Pull out the Stand to remove.
The Head part
The Stand base part
A6
Connecting the Display
To remove the Stand Base:
2. Hold the body of the Stand as it follows.
Type. A
3. Press inside the two long latches at thesame time with your strength as it follows.
5. The body of the Stand and the Stand Base are successfully separated.
4. Keep pressing the two latches and use the otherhand to hold the body of the Stand to push theStand Base in the arrow direction to remove.
1. Ensure there are two short and two longlatches at the bottom of the Stand Base.
Connecting the Display
A7
To remove the Stand Base:
2. Hold the body of the Stand as it follows.
Type. B
3. Press inside the four latches individually toward each end.
4. Put the Stand Base on a flat surface and pullup the body of the Stand while holding theStand Base with the other hand. to remove.
5. The body of the Stand and the StandBase are successfully separated.
1. Ensure there are four latches at thebottom of the Stand Base.
A8
Connecting the Display
20
Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.
Positioning your display1. Adjust the position of the panel in various ways for maximum comfort.
Tilt Range : -5˚~20˚
Ergonomic
It is recommended that in order to maintain an ergonomic and comfortable viewingposition, the forward tilt angle of the monitor should not exceed 5 degrees.
When adjusting the angle of the screen, do notput your finger(s) in between the head of themonitor and the stand body. You can hurt yourfinger(s).
Warning:
A9
2
1
Connecting the Display
Using the Computer
1. Place the monitor in a convenient, well-ventilated location near your computer. 2. Connect the signal cable. When attached, tighten the thumbscrews to secure the
connection.3. Connect the power cord into a proper power outlet that is easily accessible and close to
the display.
Wall-outlet type
PC-outlet type
DVI-D(This feature is not available in all countries.)
MAC
PC
Power CordSignal Cable
Analog signalD-sub
Digital signalDVI
Varies according to model.
1
2
Mac adapterFor Apple Macintosh use, a separate plug adapter is neededto change the 15 pin high density (3 row) D-sub VGA connectoron the supplied cable to a 15 pin 2 row connector.
NOTE This is a simplified representationof the rear view.This rear view represents ageneral model; your display maydiffer from the view as shown.
PC
19 inch monitor
A10
Connecting the Display
4. Press button on the front switch panel to turn the power on.When monitor power is turned on, the 'Self Image SettingFunction' is executed automatically.(Only Analog Mode)
NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the userconnects the monitor for the first time, this function automatically adjusts the display to optimal settings for individualinput signals. If you want to adjust the monitor while in use, or wish to manually run this function once again, push the‘AUTO/SET’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory reset’ option on theOSD adjustment menu. However, be aware that this option initializes all the menu items except ‘Language’.
Wall-outlet type
PC-outlet type
DVI-D(This feature is not available in all countries.)
MAC
PC
Power CordSignal Cable
Analog signalD-sub
Digital signalDVI
Varies according to model.
1
2NOTE This is a simplified representationof the rear view.This rear view represents ageneral model; your display maydiffer from the view as shown.
Mac adapterFor Apple Macintosh use, a separate plug adapter is needed to changethe 15 pin high density (3 row) D-sub VGA connector on the suppliedcable to a 15 pin 2 row connector.
PC
20.1 inch monitor
A11
Using the speakers - The feature is only for speaker models - L194WTM, L204WTM
Side Jack
Rear
AUDIOIN
Headphone/Earphone Input Automatically mutes the speaker volumewhen the headphones are plugged in.
Audio InputConnects to the *LINE OUT jack of thePC sound card.
*LINE OUTA terminal used to connect to thespeaker including a built-in amplifier(Amp). Make sure that the connectingterminal of the PC sound card is checkedbefore connecting. If the Audio Out of PCsound card has only Speaker Out,reduce the PC volume.
If the Audio Out of the PC sound cardsupports both Speaker Out and Line Out,convert to Line Out using the cardjumper of the program (Refer to theSound Card Manual).
*Line Out
Speaker Out
<Jack of the PC sound card>
A12
Control Panel Functions
MENU Button Use this button to enter or exit the On Screen Display.
Control Function
OSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.
Buttons Use these buttons to select or adjust functions in the OnScreen Display.
For more information, refer to page A19.
Use this button to make D-Sub or DVI connector active.This feature is used when two computers are connectedto the display. The default setting is D-Sub.
SOURCE Hot key
:
Front Panel Controls Back
A13
Control Panel Functions
This Indicator lights up blue when the displayoperates normally(On Mode). If the display is in SleepMode (Energy Saving), this indicator color changes to amber.
Use this button to turn the display on or off.Power Button
Power Indicator
Use this button to enter a selection in the On Screen Display.
AUTO/SETButton
AUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO/SET button before entering the On ScreenDisplay(OSD). This will automatically adjust yourdisplay image to the ideal settings for the currentscreen resolution size (display mode).
The best display mode is
19 inch monitor : 1440 x 90020.1 inch monitor : 1680 x 1050
Control Function
A14
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The following section is an outline of the available adjustments and selectionsyou can make using the OSD.
To make adjustments in the On Screen Display, follow these steps:
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the or Buttons. When the icon you wantbecomes highlighted, press the AUTO/SET Button.
Use the / Buttons to adjust the image to the desired level. Use theAUTO/SET Button to select other sub-menu items.
Push the MENU Button once to return to the main menu to select anotherfunction. Push the MENU Button twice to exit from the OSD.
NOTEAllow the display to stabilize for at least 30 minutes before making image adjustments.
A15
NOTE
The order of icons may differ depending on the model (A15~A19 ).
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,and setting menus.
To adjust the brightness,contrast and gamma of thescreen
PICTURE
COLOR
POSITION
TRACKING
SETUP
Main menu Sub-menu A D Reference
PRESET
RED
GREEN
BLUETo adjust the position of thescreen
To customize the color ofthe screen
To customize the screenstatus for a user's operatingenvironment
To improve the clarity andstability of the screen
BRIGHTNESS
CONTRAST
GAMMA
HORIZONTAL
VERTICALCLOCK
PHASE
SHAPNESS
WHITE BALANCE
POWER INDICATOR
FACTORY RESET
LANGUAGE
OSD HORIZONTAL
POSITION VERTICAL
sRGB
6500K
9300K
: AdjustableA : Analog InputD : Digital Input
To select or customize desired image settings
FLATRON
F-ENGINEMOVIE / TEXT
USER
NORMAL
A16
On Screen Display(OSD) Selection and Adjustment
NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.
You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.
Press the MENU Button, then the main menu of the OSD appears.
Menu Name
Icons
Button Tip
P I C T U R E
Sub-menus
MENU : Exit: Adjust (Decrease/Increase)
SET : Enter: Select another sub-menu
A17
On Screen Display(OSD) Selection and Adjustment
Main menu Sub menu Description
BRIGHTNESS
CONTRAST
GAMMA
To adjust the brightness of the screen.
To adjust the contrast of the screen.
Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues display high contrast images.
P I C T U R E
PICTURE
PRESET
RED
GREEN
BLUE
• sRGB: Set the screen color to fit theSRGB standard colorspecification.
• 6500K: Slightly reddish white.• 9300K: Slightly bluish white.
Set your own red color levels.
Set your own green color levels.
Set your own blue color levels.
COLOR
HORIZONTAL
VERTICAL
To move image left and right.
To move image up and down.
POSITION
C O L O R
P O S I T I O N
MENU : Exit: Decrease: Increase
SET : Select another sub-menu
MENU : Exit: Decrease: Increase
SET : Select another sub-menu
MENU : Exit: Decrease: Increase
SET : Select another sub-menu
A18
On Screen Display(OSD) Selection and Adjustment
Main menu Sub menu Description
CLOCK
PHASE
SHARPNESS
To minimize any vertical bars or stripesvisible on the screen background.The horizontal screen size will alsochange.
To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.
To adjust the clearness of the screen.
TRACKING
If this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. This function will be enabled only whenthe input signal is an analog signal.
SETUP To choose the language in which thecontrol names are displayed.
To adjust position of the OSD windowon the screen.
LANGUAGE
OSDPOSITION
WHITEBALANCE
FACTORYRESET
If the output of the video card is differentthe required specifications, the colorlevel may deteriorate due to videosignal distortion. Using this function, thesignal level is adjusted to fit into thestandard output level of the video cardin order to provide the optimal image.Activate this function when white andblack colors are present in the screen.
POWERINDICATOR
Restore all factory default settings except"LANGUAGE."
T R A C K I N G
S E T U P
S E T U P
Use this function to set the powerindicator on the front side of the monitorto ON or OFF.If you set OFF, it will go off. If you set ON at any time, the powerindicator will automatically be turned on.
Press the button to reset immediately.
MENU : Exit: Decrease: Increase
SET : Select another sub-menu
MENU : Exit: Adjust: Adjust
SET : Select another sub-menu
A19
On Screen Display(OSD) Selection and Adjustment
Icons
Menu Name
Sub-menu Name
Main menu Sub menu Description
To adjust the USER sub-menu function,Press the SET Button
MOVIETEXT
NORMAL
USER
When you execute F-ENGINE, two tones will appearon the screen as shown. The applied screen willappear on the left side, whereas the non-appliedscreen will appear on the right side.Touch the SETbutton to use the adjusted screen.
FLATRON F-ENGINE Screen when applied Screen when not applied
The OSD screen will appear when you touch the button
on the right side of the monitor.
TEXT: For text images (Word processing etc.)
Select the sub-menu using the SET buttonand save the YES value using the buttons.
SAVE
MOVIE: For animation images in videos or movies
This is under normal operating conditions.
This feature lets you easily select the best desiredimage condition optimized to the environment(ambient illumination, image types etc).
UserYou can manually adjust brightness, ACE or RCM. You can save or restore the adjusted value even when using a different envir
... (Brightness): Adjusts screen brightness.
...ACE(Adaptive Clarity Enhancer): Selects the clarity mode.
...RCM(Real Color Management): Selects the color mode.Not appliedGreen enhance Flesh toneColor Enhance
0
1
2
3
A20
Troubleshooting
No image appears
Check the following before calling for service.
No image appears
Do you see a "OSD LOCKED" message on the screen?
Is the power cord of thedisplay connected?
Is the power indicatorlight on?
Is the power on and thepower indicator blue orgreen?
Is the power indicatoramber?
Do you see an "OUT OFRANGE" message onthe screen?
Do you see a "CHECKSIGNAL CABLE"message on thescreen?
• Check and see if the power cord is connectedproperly to the power outlet.
• Press the Power button.
• Adjust the brightness and the contrast.
• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.
• Try to turn on the PC.
• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.
• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.
• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.
Do you see “OSDLOCKED” when youpush MENU button?
A21
Troubleshooting
Display image is incorrect
Display Position isincorrect.
On the screenbackground, verticalbars or stripes arevisible.
Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.
• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.
• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.
• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.
• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).
ImportantCheck Control Panel --> Display --> Settings and see if the frequency or theresolution were changed. If yes, readjust the video card to the recommendresolution.
The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.
A22
Troubleshooting
Have you installed the display driver?
Have you installed thedisplay driver?
Do you see an"Unrecognized monitor,Plug&Play (VESA DDC)monitor found"message?
• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lge.com.
• Make sure to check if the video card supportsPlug&Play function.
Display image is incorrect
The screen color ismono or abnormal.
The screen blinks.
• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.
• Make sure the video card is properly inserted inthe slot.
• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.
• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.
• Make sure the power voltage is high enough, Ithas to be higher than AC100-240V 50/60Hz.
A23
Specifications L194WT/L194WTQ/L194WTX
NOTEInformation in this document is subject to change without notice.
Display
Sync Input
Video Input
Resolution
Plug&Play
PowerConsumption
Dimensions&Weight
Tilt Range
Power Input
EnvironmentalConditions
Stand Base Signal cablePower cord
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating19 inches viewable0.2835 mm pixel pitch
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)Digital : 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate TTL, Positive/Negative
SOG (Sync On Green) Digital
Signal Input 15 pin D-Sub ConnectorDVI - D connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max Analog : VESA 1440 x 900 @75 HzDigital : VESA 1440 x 900 @60 Hz
Recommend VESA 1440 x 900 @60 Hz
DDC 2B
0n Mode : 34 W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤ 1 W
With Stand Without Stand
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inchesDepth 22.60 cm / 8.89 inches 5.87 cm / 2.31 inches
Net 3.6 kg (7.94 lbs)Tilt -5˚~20˚AC 100-240V~ 50/60Hz 0.8A
Operating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-Condensing
Storage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
A24
Specifications L194WTM
Display
Sync Input
Video Input
Resolution
Plug&Play
PowerConsumption(without speaker)
Dimensions&Weight
Tilt Range
Power Input
EnvironmentalConditions
Stand Base Signal cablePower cord
19 inches (48.2 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating19 inches viewable0.2835 mm pixel pitch
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)Digital : 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate TTL, Positive/Negative
SOG (Sync On Green),DigitalSignal Input 15 pin D-Sub Connector
DVI - D connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max Analog : VESA 1440 x 900 @75 HzDigital : VESA 1440 x 900 @60 Hz
Recommend VESA 1440 x 900 @60 Hz
DDC 2B
0n Mode : 34 W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤ 1 W
With Stand Without Stand
Width 43.48 cm / 17.11 inches 43.48 cm / 17.11 inches
Height 36.99 cm / 14.56 inches 28.73 cm / 11.31 inchesDepth 22.60 cm / 8.89 inches 5.87 cm / 2.31 inches
Net 3.6 kg (7.94 lbs)Tilt -5˚~20˚
AC 100-240V~ 50/60Hz 0.8A
Operating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-Condensing
Storage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Audio RMS Audio Output 1W+1W(R+L)
Input Sensitivity 0.7VrmsSpeaker Impedance 16Ω
NOTEInformation in this document is subject to change without notice.
A25
Specifications L204WT/L204WTQ/L204WTX
NOTEInformation in this document is subject to change without notice.
Display
Sync Input
Video Input
Resolution
Plug&Play
PowerConsumption
Dimensions&Weight
Tilt Range
Power Input
EnvironmentalConditions
Stand BaseSignal cablePower cord
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating20.1 inches viewable0.258 mm pixel pitch
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)Digital : 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate TTL, Positive/Negative
SOG (Sync On Green) Digital
Signal Input 15 pin D-Sub ConnectorDVI - D connector (Digital)
Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max Analog : VESA 1680 x 1050 @ 60 HzDigital : VESA 1680 x 1050 @ 60 Hz
Recommend VESA 1680 x 1050 @60 Hz
DDC 2B
0n Mode : 45W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤ 1 W
With Stand Without Stand
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches Depth 22.60 cm / 8.89 inches 6.46 cm / 2.54 inches
Net 4.8 kg (10.58 lbs)
Tilt -5˚~20˚AC 100-240V~ 50/60Hz 1.2A
Operating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-Condensing
Storage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
A26
Specifications L204WTM
Display
Sync Input
Video Input
Resolution
Plug&Play
PowerConsumption(without speaker)
Dimensions&Weight
Tilt Range
Power Input
EnvironmentalConditions
Stand Base Signal cablePower cord
20.1 inches (51.1 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating20.1 inches viewable0.258 mm pixel pitch
Horizontal Freq. Analog : 30 - 83 kHz (Automatic)Digital : 30 - 83 kHz (Automatic)
Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate TTL, Positive/Negative
SOG (Sync On Green) DigitalSignal Input 15 pin D-Sub Connector
DVI - D connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital
Max Analog : VESA 1680 x 1050 @60 HzDigital : VESA 1680 x 1050 @60 Hz
Recommend VESA 1680 x 1050 @60 Hz
DDC 2B
0n Mode : 45W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤ 1 W
With Stand Without Stand
Width 46.62 cm / 18.35 inches 46.62 cm / 18.35 inches
Height 38.40 cm / 15.11 inches 30.54 cm / 12.02 inches Depth 22.60 cm / 8.89 inches 6.46 cm / 2.54 inches
Net 4.8 kg (10.58 lbs)
Tilt -5˚~20˚AC 100-240V~ 50/60Hz 1.2A Operating Conditions
Temperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-Condensing
Storage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-Condensing
Attached ( ), Detached ( O )
Attached ( ), Detached ( O )
Wall-outlet type or PC-outlet type
Audio RMS Audio Output 1W+1W(R+L)
Input Sensitivity 0.7VrmsSpeaker Impedance 16Ω
NOTEInformation in this document is subject to change without notice.
A27
Specifications
Preset Modes (Resolution)
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
123456789
1011121314
*15**16
640 x 350720 x 400640 x 480640 x 480800 x 600800 x 600832 x 6241024 x 7681024 x 7681152 x 8701152 x 9001280 x 10241280 x 10241440 x 9001440 x 9001440 x 900
31.46931.46831.46937.50037.87946.87549.72548.36360.12368.68161.80563.98179.97655.50055.93570.635
70706075607575607575656075606075
*Recommend Mode**Only Analog Mode
Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)
123456789
10*11
**12
720 x 400640 x 480640 x 480800 x 600800 x 6001024 x 7681024 x 7681152 x 8641280 x 10241280 x 10241680 x 10501680 x 1050
31.46831.46937.50037.87946.87548.36360.12367.50063.98179.97664.67465.290
706075607560757560756060
* Digital Recommend Mode** Analog Recommend Mode
19 inch monitor
20.1 inch monitor
A28
Signal Connector Pin Assignment
1 89
17 2416
Pin Signal(DVI-D)123456789101112131415
T. M. D. S. Data2-T. M. D. S. Data2+T. M. D. S. Data2/4 ShieldT. M. D. S. Data4-T. M. D. S. Data4+DDC ClockDDC DataAnalog Vertical Sync.T. M. D. S. Data1-T. M. D. S. Data1+T. M. D. S. Data1/3 ShieldT. M. D. S. Data3-T. M. D. S. Data3++5V PowerGround (return for +5V, H. Sync. and V. Sync.)
Pin Signal(DVI-D)161718192021222324
Hot Plug DetectT. M. D. S. Data0-T. M. D. S. Data0+T. M. D. S. Data0/5 ShieldT. M. D. S. Data5-T. M. D. S. Data5+T. M. D. S. Clock ShieldT. M. D. S. Clock+T. M. D. S. Clock-
T. M. D. S. (Transition Minimized Differential Signaling)
DVI-D Connector
Specifications
Indicator
On ModeSleep ModeOff Mode
blueamber
Off
LED ColorMODE
Installing the Wall mount plate
A29
This monitor satisfies the specifications of the Wall mount plate orthe interchange device.1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on
the cushion or soft cloth.
3. Hold the product as it follows and lift up the Stand slightly.
4. Change your hold on the product as it follows and turn the Stand Base in the arrowdirection.
5. Pull out the Stand to remove.
The Head part
The Stand base part
A30
Installing the Wall mount plate
Wall mount plate(Separate purchase)This is stand-type or will mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plate ispurchased.
Kensington Security SlotConnected to a locking cable that can be purchasedseparately at most computer stores
6. Install the Wall mount plate.
Digitally yours