lift truck operator training program by hbaa
DESCRIPTION
TRANSCRIPT
![Page 1: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/1.jpg)
Alabama Homebuilders Self Insurers Fund
Lift Truck Operator Training Program
Presented by the AHBSIF Loss Control Department
![Page 2: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/2.jpg)
Course Outline
I. Introduction
II. Lift Truck Basics
III. Fuels and Batteries
IV. Emergency Situations
V. Fundamentals of Operation
VI. Driving Test
![Page 3: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/3.jpg)
I. Introduction
![Page 4: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/4.jpg)
This presentation will provide participants with the following:– The importance of lift truck safety– Component, weight, stability, and speed
characteristics of lift trucks– Safe handling of fuels and batteries– Daily maintenance and safety check
procedures
![Page 5: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/5.jpg)
II. Lift Truck BasicsSection 1 - Awareness
![Page 6: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/6.jpg)
Recognition of emphasized messages:
– NOTE• This message is used when special information,
instructions, or identification is required relating to procedures, equipment, tools, pressures, capacities, and other special data.
– IMPORTANT• This message is used when special precautions
should be taken to ensure a correct action or to avoid damage to, or malfunction of, the truck or a component.
– CAUTION• This message is for proper precautions which, if
not followed, can result in personal injury.– WARNING
• This message is used when a hazard exists which can result in injury or death if proper precautions are not taken.
– DANGER• This message is used when an extreme hazard
exists which will result in death or serious injury if proper precautions are not taken immediately.
![Page 7: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/7.jpg)
Benefits of Operator Training
Improved safety for the operator and others The operator learns how to perform a pre-shift inspection
– Reduce down time and maintenance costs– Increase productivity– Improve safety
The equipment is better cared for– Employees understand the value of the equipment and how to
use it efficiently Operator training and progress is documented OSHA requirements are fulfilled
![Page 8: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/8.jpg)
Forklift Types
Narrow Aisle
Picker
Electric Standup
![Page 9: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/9.jpg)
Forklift Types
Powered Pallet Truck Sit Down Rider
(Pneumatic Tire)
![Page 10: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/10.jpg)
• Section 2 – Components and Stability
![Page 11: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/11.jpg)
Components of a Lift Truck
Overhead GuardUpright
Operator Restraint System
Counterweight
Steer Axle and Wheels Drive Axle and
Wheels
Lift Cylinder
Tilt Cylinder
BackrestFuel Tank
Carriage
![Page 12: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/12.jpg)
Data Plate
• The data plate must be in legible condition
• A data plate provides the following information:– Maximum lift height– Attachment capacities– Maximum weight
capacities
![Page 13: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/13.jpg)
Lift Truck Weight
• Listed capacities are not good indicators of the machines total weight
• A lift truck can weigh two to three times as much as the lifted capacity
• A lift truck usually weighs twice its capacity2:1 ratio
Component Estimated lbs
Truck Weight 8,000 lbs
Capacity 4,000 lbs
Operator 175 lbs
Total 12,175 lbs
![Page 14: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/14.jpg)
Load Center
The load center rating of a fork truck is the maximum distance from the face of the forks to the center of gravity of a capacity load.
The data plate will have this information.
Standard forks measure 24” at the load center.
For every inch beyond the rated load center that the load is placed, approximately 100 lbs. of capacity is lost.
![Page 15: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/15.jpg)
Load Center
24”
![Page 16: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/16.jpg)
Stability
Even though a forklift has four wheels, it is only supported at three points.
The steering axle of most four-wheel lift trucks is attached by means of a pivot point in the center of the axle.
![Page 17: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/17.jpg)
Center of Gravity The black spot in the triangle below represents the
Center of Gravity. The Center of Gravity (CG) shifts according to the
movements of the truck. If the CG moves outside the triangle the truck will
overturn.
![Page 18: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/18.jpg)
Figure 1 shows the CG shift when the truck is loaded and braking.
Figure 2 shows the CG shift when the truck is uneven or turning with excessive speed.
Center of Gravity
![Page 19: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/19.jpg)
Center of Gravity
As the CG gets higher, the stability of the lift truck gets smaller.
Loads must be kept as low as possible at all times.
Zone 3
Zone 2
Zone 1
Stability
Lif
t H
eig
ht
![Page 20: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/20.jpg)
• Section 3 – Safety Equipment
![Page 21: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/21.jpg)
Common Safety Devices Roll Over Protection System (ROPS)
– Designed to minimize complete overturn– Employees should never jump from a machine during overturn– Integral Components include:
• Overhead Protection• Seatbelt• Protective cage
Pedestrian Warning Devices– Lights
• Headlights, Brake Lights• Amber Strobes
– Horn and Back-Up Alarm Operator’s Manual
– Includes safe operating procedures and capacities
![Page 22: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/22.jpg)
III. Fuels and Batteries
![Page 23: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/23.jpg)
Liquefied Petroleum Gas (LPG)
Burns cleaner than gas engines.Produces a poisonous gas that is not
easily detectable, must be operated in well ventilated areas.
LPG is heavier than air and will seek low lying areas.
LPG is extremely flammable, must avoid all sources of ignition
![Page 24: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/24.jpg)
Liquefied Petroleum Gas (LPG)
It acts like a liquid. It can soak into clothing.
It is compressed under high pressure in the tank.
LPG in liquid state has a temperature of 44° below zero. Can cause frostbite on contact with skin.
Chemicals are added to give the gas an odor which helps identify leaks.
![Page 25: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/25.jpg)
LPG Tank Handling & Storage
A specified area should be designated for the storage and changing of LPG tanks.
Tanks should always be stored in their upright position with all gauges and valves at the top whether empty or full.
When trucks are parked overnight or for extended periods, the service valve of the tank must be closed.
Never park a truck near a source of heat. Always wear proper safety equipment when
handling tanks (safety glasses, heavy rubber gloves).
![Page 26: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/26.jpg)
LPG Tank Removal
Wear proper personal protective equipment. Do not smoke. Purge the fuel line by closing the tank’s service
valve and waiting for the engine to run out of fuel. (Controls in neutral, forks down, brake on, ignition off.)
Once the service valve is closed, unscrew the line connection and move the hose out of the way.
Carefully remove the tank from the mounting bracket.
![Page 27: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/27.jpg)
LPG Tank Installation
Select a replacement tank in good service condition.
Do not roll or drag the new tank to the machine. Use a cart or other suitable equipment.
Position the tank in the mounting bracket by aligning the collar hole over the mounting bracket pin. (this is important for fuel consumption and safety)
Check all rubber seals in the tank and fuel line connection.
![Page 28: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/28.jpg)
LPG Tank Installation
Reconnect the fuel line connection until tight.
Slowly turn on the service valve to full and slightly backseat.
Make sure both tank clamps are adjusted properly and hold the tank firmly.
If no leaks are detected, start the truck and check for normal operation.
![Page 29: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/29.jpg)
Compressed Natural Gas (CNG)
The same natural gas that powers hot water heaters and furnaces.
CNG is different than LPG in that it remains a gas even under high pressure.
CNG is lighter than air and dissipates rapidly when released.
CNG tanks are usually permanently mounted to the lift truck.
![Page 30: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/30.jpg)
Gasoline and Diesel
The difference between these two fuels is their ignition temperatures.
Gasoline– Extremely flammable– Colorless– Distinctive odor
Diesel– Has higher ignition point than gas– Colorless– Slight odor, harder to detect than gas
![Page 31: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/31.jpg)
Gas and Diesel Refueling
Most lift trucks filler caps are equipped with a venting device and a fuel screen.
The screen serves as a fire retardant device by keeping fire out of the fuel tank.
Check when refueling to make sure the screen is in place.
![Page 32: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/32.jpg)
Gas and Diesel Refueling
Safe refueling checklist:– Refuel in designated areas with good
ventilation– Smoking and open flames are prohibited– Shut off the truck, lower the forks, put the
truck in neutral, and set the parking brake before beginning
– Don’t overfill the tank– Clean up any spills– Use only clean, properly marked fuel cans
![Page 33: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/33.jpg)
Batteries
A lead-acid battery is a portable power source for supplying direct current electricity.
The most common voltages include 12, 24, 36, and 48 volts.
Discharging a battery below 80% of its total capacity can result in shortened battery and truck component life.
![Page 34: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/34.jpg)
Battery Hazards
Sulfuric Acid – Small amounts can cause severe contact burns to the skin.
Gasses – Batteries produce hydrogen and oxygen mixture continuously. Keep all ignition sources away.
Electricity – Batteries are capable of producing very high discharge rates. Avoid direct shorting situations.
Battery Weight – Use care when handling, charging, and using batteries in the truck.
![Page 35: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/35.jpg)
Battery Chargers
Two types:– Single Phase charger has two wires and a ground
with one transformer and two fuses.– Three Phase charger has three wires and a ground in
the power supply cable. It has three transformers and three fuses.
Always correctly match the charger to the voltage and amp hour ratings of the battery.
Also check the input voltage and cycle. Input voltage is most commonly 220, 440, or 480, with US Standard 60 cycles.
![Page 36: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/36.jpg)
Battery Charging
Battery recharging requires a special service area in accordance with OSHA section (g)(1). The area must be:– Well ventilated– Truck off, set parking brake– Jewelry is prohibited– Personal protective equipment should include safety
glasses, head protection, aprons, and gloves– All battery cables should be disconnected before
charger hook-up– Handling must be done according to manufacturers
recommendations
![Page 37: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/37.jpg)
Battery Charging
– Vent caps must be left on during charging.– If the battery is charged while still in the truck, the
compartment must be left open.– The charger should be turned off before it is
connected to the battery then turned on to begin the charging cycle.
– Color coded connectors help prevent connecting a battery of the wrong voltage to the wrong charger or truck.
– Chargers should be properly set to avoid over or under charging.
– The charger should be turned off before disconnecting from the battery.
![Page 38: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/38.jpg)
IV. Emergency Situations
![Page 39: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/39.jpg)
Are you prepared?
Does the facility have an evacuation procedure?
Are emergency contact numbers readily available?
Do any of your employees/co-workers have CPR or First Aid training?
Does the facility have a first aid kit?
![Page 40: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/40.jpg)
Handling an Emergency
The three C’s, Check, Call, Care help us remember what to do in an emergency situation.
Check – check the area for your own safety first, then the victim's
Call – for help, 911 or whom ever is in the immediate area that can provide assistance
Care - administer care to the victim, this may be first aid or at least stabilization
![Page 41: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/41.jpg)
Fire Prevention - Extinguishers
Ordinary Combustibles
Includes materials such as wood and paper
Flammable Liquids
Includes fuels, grease, other liquids
Electrical Fires
Contains non-conductive smothering agent
![Page 42: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/42.jpg)
How to Use a Fire ExtinguisherP-A-S-S
Pull -- Pull the pin at the top of the extinguisher that keeps the handle from being activated
Aim -- Aim the nozzle at the base of the fire
Squeeze -- Maintain a distance of eight to ten feet away from the fire and squeeze the handle. Discharge will only occur if the handle is being squeezed.
Sweep -- Sweep the nozzle back and forth at the base of the fire until it appears to be out.
![Page 43: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/43.jpg)
V. Fundamentals of Operation
![Page 44: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/44.jpg)
Safe Truck Operation
Trained Operators Only– OSHA requires that only trained operators be allowed
to operate fork trucks Stunt Driving and Horseplay is Strictly Prohibited
– Fork trucks are heavy and powerful machines that demand an operators attention and respect
Read and Understand Operator Instructions– You must read and understand the operators manual
for each truck you operate Faulty Equipment and Maintenance
– If at any time the fork truck is in need of repair or defective in any way, it must be taken out of service and fixed
![Page 45: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/45.jpg)
Operating Around Personnel
Operators should not rely on pedestrian warning devices and mirrors.
Know the terrain and visibility of your workplace. Sound your horn at intersections and blind
spots. If your view is blocked because of the load,
travel backwards. If you must move forward, make sure that people are out of the way and move the lift truck slowly.
![Page 46: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/46.jpg)
Operating Around Personnel
Never attempt to move a load that requires someone to steady or position the material.Restack the load and/orSecure the load to a pallet.
Never drive the fork truck up to someone in front of a fixed object. Avoid potential “caught between” exposures.
![Page 47: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/47.jpg)
Upright and Fork Safety
Never allow anyone to walk under raised upright whether loaded or empty.
Never allow anyone to stand on the forks or climb the upright assembly.
Never allow anyone to reach or to step in the areas of the mast, carriage, forks, or load.
Never allow anyone to ride on the truck.
![Page 48: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/48.jpg)
Leaving or Parking the Truck
OSHA considers a fork truck unattended if the operator is 25 feet away or out of sight of the truck. Use the following tips when leaving the truck or parking it for long periods:
Bring the machine to a complete stop. Turn off the engine, for LPG trucks, shut off
the service valve and let the engine run out of fuel.
Lower all attachments completely. Put the forks on the floor.
Place all controls in neutral.
![Page 49: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/49.jpg)
Leaving or Parking the Truck
Apply the parking brake. Never park on a grade or around traffic. Never leave the truck parked on a dock ramp,
dock leveler, or in a trailer. Never park the truck where it blocks emergency
or fire-fighting equipment or emergency travel routes.
Chock the wheels if needed. Turn off power supply and remove the keys if
possible.
![Page 50: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/50.jpg)
Personnel Elevators
Lift trucks are not designed to lift people.There are machines designed for this
purpose;– Scissor lifts– Order Pickers (platform lift)– Elevated work platforms
OSHA does allow the practice under specific conditions (ASME B56.1).
![Page 51: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/51.jpg)
Personnel Elevators
Must be designed by a professional engineer
Must be designed to work with a specific lift
Occupants must wear a harness and lanyard
Operators must man controls at all times
![Page 52: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/52.jpg)
Lift Truck Tip Over
In case of a tip-over, use the following precautions:– Wear your seatbelt.– Never attempt to leap from the truck.– Grip the wheel firmly with both hands.– Brace your feet firmly against the floor boards.
![Page 53: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/53.jpg)
Handling Loads
Always balance and secure the load.Never pick loads that are too heavy.Be aware of your clearances at all times.
Check for overhead obstructions or power lines.
Center the load. Forks must be at least 2/3 the length of the load.
![Page 54: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/54.jpg)
Handling Loads
≤ 2/3 Length
![Page 55: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/55.jpg)
Handling Loads
When picking up a load, place the forks under the load as far as possible.
Tilt the mast back slightly for stabilization.Keep the load low. The forks should never
be more than 6 to 8 inches from the ground.
![Page 56: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/56.jpg)
Stacking Square the truck to the
rack/bin and come to a complete stop
Elevate the load to the proper height and Inch the truck in
Tilt the load forward for placement.
Lower the forks to take pressure off the pallet.
Back the truck up till the forks clear and lower them before traveling.
Use the same procedure in reverse when picking up a load from a stack.
![Page 57: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/57.jpg)
Traveling Understand the traffic
laws of your environment Familiarize yourself with
the work area.- Visibility- Travel surface
Maintain at least a three truck length distance between yourself and any truck ahead.
Always yield the right-of-way to any emergency vehicle
![Page 58: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/58.jpg)
Traveling Grades, Ramps, and
Inclines– Travel must be straight up
and straight down. Never turn on ramps, slopes, or inclines.
– With a load, travel up or down with the load pointing upgrade.
– Without a load, travel up or down with the forks pointing downgrade.
– The load should be tilted back and raised only as high as necessary to clear the surface.
![Page 59: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/59.jpg)
Traveling
Dock Operations– Before entering a tractor trailer make certain the
wheels are chocked.– Check the trailer jacks. Make sure they are fully
lowered and secured.– Inspect the floor of the trailer prior to driving on it.– Check the dock boards between the trailer and the
dock. Always travel slowly over dock boards.– Stay away from the edge of the dock.– Use lights to improve visibility while working in trailers.
![Page 60: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/60.jpg)
Hands-On Section
• Pre-operation Inspection
• Familiarization with operating controls and gauges
• Driving exercises– Figure 8 Test– Reverse Mobility– Lifting and Carrying
![Page 61: Lift Truck Operator Training Program by HBAA](https://reader035.vdocument.in/reader035/viewer/2022081602/54bc23484a7959791e8b456f/html5/thumbnails/61.jpg)
Pre-Operational ChecklistItem Ok repair Item Ok repair
Forks, Backrest, Carriage Leaks under Fork Lift
Mast, Chain, Hydraulic Lines
Seat and Seat belts
Tires, Axles Horn and/or Backup alarm
Overhead Guard/ROPS Lights, Bodywork
Fuel Tank & Connections Gauges and Instruments
Fuel Level Hydraulic Controls & Lift
Engine Oil Level All Brakes
Radiator Water Level (Cold)
Steering