lighting control 53...univ: 1-16 (16) supernode add: 1 risk of electric shock. disconnect power...

1. All consoles, NPU’s, 3d Computers MUST have the same software loaded!. 2. Connected consoles should be used to program to mitigate the risk of the Master console failing during output. 3. Add 1 millisecond to both the Artnet and sACN output ‘delay' fields in "setup/networking/network protocols"4. sACN protocol field should be set to “FINAL” in ”setup/networking/network protocols"5. Ethernet Port 1(eth 0) is MA/sACN Net and Ethernet Port 2 (eth 1) is Artnet Only!6. Spare NPU's are NOT spare if they are plugged in. The MA shares the processor load across all NPU's on the network. Ensure system can operate without spare first, then add spare to network which will take the load if any NPU fails.7. NPUs generate a high level of network traffic. Use the lowest number of NPUs required for parameter count. 8. Only the Master Console in a session will listen/send sACN/Artnet. 9. DISABLE “Network DMX if Alone” within Network Protocols menu. 10. Priority levels must be set in order to retain station configuration. 11. Artnet data corruption can occur if a previous master and new master are both connected to the Artnet network.12. Do NOT use RDM in show conditions. DMX data is not reliable while RDM is discovering and may not be compatible with S400.13. Any MA 3D, onPC, or other MA device that is powered down MUST be physically unplugged from network!!14. Rob Base Lesson #2...It takes two to make it outta sight!

MA2 Special Notes

1. All Fiber Optic runs, regardless of overall length, MUST NOT be made up of more then five lengths of cable2. NO ETHERCON or CAT5E COUPLERS!!3. S400 Supernodes should be set to “Merge2” to avoid any conflicts during a system failure. 4. Do NOT use RDM in show conditions. DMX data is not reliable while RDM is discovering If RDM must be used, leave “incremental” unchecked. 5. All VIA 12 switches MUST have the same software loaded and have unique IP addresses6. All switches should be defaulted inc Network Settings prior to configuration. 7. All VIA 12 Port Speeds should be set to “Auto Negotiate” 8. VLAN = Virtual Local Area Network (VLANS are like groups they only talk to other ports configured as the same VLAN9. Managment VLAN = 1.10. When using VLAN’s Ports 11-12 (Cat5e on rear) and Ports 13-14 (Fiber Ports) must be set to TAGGED/UPLINK so as to pass ALL VLAN traffic10. Rob Base Lesson #1...It takes two to make a thing go right.

Important System Notes!

Pete V676 PreVis

Supernode Add: 5

Supernode Add: 4

Supernode Add: 3

Supernode Add: 2

Supernode Add: 1

7-Port Switch V676

7-Port Switch Artnet

LiteConverse

Cat 5e (Artnet)

PETE’S PREVISOF PLEASURE

LIGHTING CONTROL LAYOUT

COUNTS

Cat 5e (Artnet)

OptiCon DuoFiber

Cat 5e(MA Artnet)

KEY

Cat5e(V676)

SUPERBOWL Halftime

LX NETWORK

DATE: 1/23/19 0922 SCALE: VISUAL ONLY

DRAWN BY: CONTI ©2019 PRG

REV E

350’ Limo Fiberx8 Active & Spare

VIA12 Switchx22 Active & SpareU506K

S400 Rackx7 Active 3838T-

Risk of electric shock.Disconnect power

before opening.Risque de decharge

electrique. Debrancherle pouvoir avant

d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION

48VDC PoE INPUT200W MAX

AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH

PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8 PORT 9 PORT 10

NodePlusx14 Active & Spare37999-

SuperNodex223799C-

10-PortSwitchx11 Active & Spare3132K-

350’ OptiCon Duo Fiberx4 Active & Spare


Spare OptiCon DuoFiber


OptiCon Duo Couplersx8 Active & Spare

Limo Fiber

Cat 5e(MA/ sACN Net)

Cat 5e (UPLINK)

SpareLimo Fiber

FOH MovesLike Jagger

Pete V676 Main

Univ: 46-55 (10)

Supernode Add: 5

Univ: 36-45(10)

Supernode Add: 4

Univ: 25-35 (11)

Supernode Add: 3

Univ: 17-24 (8)

Supernode Add: 2

Univ: 1-16 (16)

Supernode Add: 1




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


VIA12 Gigabit SwitchIP Add: 10.66.201.001




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

SessionID: 1 SBLII

SPARE

grandMA 2 Lite: JasonMAIN (High)eth0 Add: 192.168.0.1eth1 Add: 10.66.0.1

Pete V676 Backup

Cat 5e (v676)

Node Plus FILTER

(S400 Mode)Add:11

Univ: 98,99,x,x,x,x

grandMA 2 Lite: PYRO MAIN (High)eth0 Add: 192.168.0.201eth1 Add: 10.66.0.201

grandMA 2 Lite: JasonSPARE (Normal)eth0 Add: 192.168.0.2eth1 Add: 10.66.0.2


VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


S400 ToolsIP Add:10.66.200.1

Cat 5e (Artnet)

10-Port Switch



VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

SPARE

Cat 5e (MA Artnet)

VIA12 Gigabit SwitchIP Add: 10.66.201.003VLAN 1: V676 Artnet Ports 1-5VLAN 2: MA/sACN ports 6-10UPLINK: All Data Ports 11-14 VIA12 Gigabit Switch

IP Add: 10.66.248.003VLAN 1: V676 Artnet Ports 1-5VLAN 2: MA Artnet Ports 6-10UPLINK: All Data Ports 11-14

SPARE

CATWALK SWITCHES

SUITES & 200 LEVEL SWITCHES

FIELD SWITCHES

West Truss

Cat 5e (Artnet)

Univ: 56-64 (9)

Supernode Add: 6

Cat 5e (v676)

Cat 5e (v676)

Cat 5e (v676)

Cat 5e (Artnet)

Cat 5e (Artnet)

10-Port Switch

Cat 5e (Artnet)

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Hippo 1: 192.168.0.31Artnet IP: 10.66.0.31

IP Add: 192.168.0.11NPU #1

IP Add: 192.168.0.12NPU #2

IP Add: 192.168.0.13

NPU #3

NW-DSL Field Rack

Univ: 47,48,53,x,x,x,98,99

Addr: 711Supernode (S400 Mode)

Cat 5e (Artnet)

VIA12 Gigabit SwitchIP Add: 10.66.207.011VLAN 1: V676 Artnet Ports 1-5VLAN 2: MA/sACN ports 6-10UPLINK: All Data Ports 11-14




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Supernode (S400 Mode)





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Cat 5e (Artnet)

NE-DSR Field Rack

Univ: 52,x,x,x,x,x,98,99


Cat 5e (Artnet)

Univ: 52,x,x,x,x,x,x,98,99





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH







d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Cat 5e (Artnet)

PathfinderIP Add: 192.168.0.51

SE-USR Field Rack

Univ: 40,41,46,47,48,52,x,x


Univ: 56,57,58,59,36,37,38,39







d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Univ: 40,41,46,47,48,52,x,x

Addr: 732Supernode (S400 Mode)Supernode (S400 Mode)




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Univ: 56,57,58,59,36,37,38,39

Addr: 731

SW-USL Field Rack

Univ: 49,50,51,53,x,x,98,99








d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Cat 5e (Artnet)

Addr: 742Supernode (S400 Mode)Supernode (S400 Mode)




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Cat 5e (Artnet)

Univ: 60,61,62,63,42,43,44,45

Addr: 741

CART #25

S400 Rack 111 S400 Rack 121

VIA12 Gigabit SwitchIP Add: 10.66.207.111VLAN 1: V676 Artnet Ports 1-10UPLINK: All Data Ports 11-14

VIA12 Gigabit SwitchIP Add: 10.66.247.111VLAN 1: V676 Artnet Ports 1-10UPLINK: All Data Ports 11-14

SPARERisk of electric shock.

Disconnect powerbefore opening.

Risque de dechargeelectrique. Debrancher

le pouvoir avantd'ouvrier.

90-260VAC.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


S400 Rack 211

North Truss




d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH






d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH



SPARE

East Truss

S400 Rack 421

South Truss

S400 Rack 411

Cat 5e (Artnet)

214 Rackland

SPARE Univ: 31,33,35,x,x,x





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH


Node Plus (S400 Mode)

Add:222

Univ: 31,33,35,x,x,x


Add:221

Univ: 28,29,x,x,x,x

Cat 5e (Artnet)





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH



Add:224


Add:223

Cat 5e (Artnet)

SPARE Univ: 28,29,x,x,x,x,

SPARE

SPARESPARE

SPARE SPARE

208 Rackland






d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH



Add:232

Univ: 30,31,32,x,x,x


Add:231

Univ: 25,26,27,x,x,x

Cat 5e (Artnet)





d'ouvrier.90-260VAC

.75A 50/60 Hz

ATTENTION


AC THRUMAX 10A

VIAMANAGED GIGABIT

POELINK/ACT

ETHERNET SWITCH



Add:234


Add:233

Cat 5e (Artnet)


SPARE

Cat 5e (UPLINK)

Cat 5e (UPLINK)

Cat 5e (UPLINK)

TO FIELD TO SUITES & 200 Level

TO CATWALK

CATWALK FIBER1200’ OptiCON Duo Fiber x 2

(4 x 600’ + 2 x Coupler)

FIELD FIBER950’ OptiCON Duo Fiber x 3

(3 x 600’ + 3 x 350’ + 3 x Coupler)

600’

Opt

iCO

N D

uo F

iber

x 2

(2 x

600

’ )

250’ OptiCON Duo Fiber x 2(2 x 250’ )




550’ Limo Fiber x 2(2 x 350’+ 2 x 200’ )

Univ: 47,48,53,x,x,x,98,99

Addr: 712

Univ: 98,99,x,x,x,x

Node Plus Add: 733

Univ: 98,99,x,x,x,x

Node Plus Add: 736

Cat 5e (Artnet)Cat 5e (Artnet)

SPARESPARE

SPARE

Univ: 49,50,51,53,x,x,98,99Univ: 60,61,62,63,42,43,44,45SPARE SPARE

SPARESPARE

Univ: 103,106,109,112,145,124,136Univ:103,106,109,112,145,124,136

Node Plus Add: 803

Univ: 98,99,x,x,x,x

Node Plus Add: 806

SPARE Univ: 98,99,x,x,x,x

Addr: 804Supernode (S400 Mode) 114/134

113/135110/111107/108104/105101/102115/139116/140116/141117/141

120/134121/135122/125125/126128/129131/132119/138119/142118/144117/147

Supernode (S400 Mode)Addr: 801

S400 ToolsIP Add:10.66.200.2

SUITES & 200 LEVEL FIBER1250’ OptiCON Duo Fiber x 2

2 x 1000’ + 2 x 250’+ 2 x Coupler)

PROGRAMING FIBER350’ Limo Fiber x 2

(2 x 350’)


Pete’s ProgramingPosition of Sugar

Supernode Add: 6

Cat 5e (v676)

Cat 5e (Artnet)

IP Add: 10.66.0.41

grandMA 3D IP Add: 192.168.0.3

Univ12/x12/x13/x13/x14/x14/x20/x21/xx/xx/x

Univ1/x1/x2/x2/x3/x3/x4/x4/xx/xx/x

Univ6/x6/x7/x8/xx/xx/xx/xx/xx/xx/x

S400 Rack 511Univ9/x9/x

10/x11/x11/x18/x19/xx/xx/xx/x

10-Port Switch

10-Port Switch

Cat 5e (Artnet)Cat 5e (Artnet)

SPARE

10-Port Switch

S400 Rack 311

Cat 5e (Artnet)

Univ15/x15/x16/x17/xx/xx/xx/xx/xx/xx/x

10-Port Switch

10-Port SwitchSPARE

10-Port Switch

10-Port Switch

SPARE

10-Port Switch

550’ Limo Fiber x 2(2 x 350’+ 2 x 200’ )

550’ Limo Fiber x 2(2 x 350’+ 2 x 200’ )

CISCO SG112 Gigabit SwitchIP Add: 192.168.101.2

Hippo 2: 192.168.0.32Artnet IP: 10.66.0.32

IP Add: 192.168.0.21NPU #4

IP Add: 192.168.0.22NPU #5

IP Add: 192.168.0.23

NPU #6

CISCO SG112 Gigabit SwitchIP Add: 192.168.101.1

Cat 5e

(MA/sAC

N N

et)



Cat 5e (MA/sACN Net)Cat 5e (MA/sACN Net)


200’ Limo Fiberx8 Active & Spare

Univ: 127,130,133,145,146,


Cat 5e(MA/sACN Net)


Univ:127,130,133,145,146

Cat 5e(Artnet)

Cat 5e(MA/sACN Net)

Cat 5e(Artnet)

Cat 5e(MA/sACN Net)

Glow MotionIP Add: 192.168.0.53

lighting control 53...univ: 1-16 (16) supernode add: 1 risk of electric shock. disconnect power...

Documents