list programs mode the haas control series press three times to get to this page (continued on next...
TRANSCRIPT
PRESS
THREE TIMES TO GET TOTHIS PAGE
(Continued onnext slide)
Note:
SLIDE LEGEND
ACTIONS
INSTRUCTIONS
KEYS
INFORMATION
To advance through the presentation
click on your left mouse button
or press <ENTER>.
To exit press <ESC>.
To advance through the presentation
click on your left mouse button
or press <ENTER>.
To exit press <ESC>. OTHER INFORMATION
LIST PROGRAMS MODE
This module is intended to provide
you with a
familiarizationof the List Programs Mode on the Haas
Control
List Programs Buttons
LIST PROGRAMS:
SELECT PROGRAM:
SEND RS232:
RECEIVE RS232:
ERASE PROGRAM:
Pressing the List Program button on the control will display a list of all of the programs loaded in the control, up to a maximum of 500 programs.
List Programs Button:
PROGRAM (LIST PROG) O91002 N00000
List Programs Button:
Press<LIST PROG>
This will bring up the Programs screen and display the programs
loaded in the control, up to 500 maximum.
An asterisk (*) will be to the left of the selected
program.
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
O00123 (Mill HMC2)
List Programs Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
O00123 (Mill HMC2)
To highlight a program for selection do one or a
combination of the following:
Cursor Up or Down
Scroll using the Hand Wheel.
Press<HOME> to get to the
top of the list.
Press<END> to get to the
bottom of the list.
To highlight and Select a program.
Type in the program number and Press <WRITE/ENTER>
Select Program Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
* O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
O00123 (Mill HMC2)
Select Program Button:
When the program you want is highlighted
Press<SELECT PROG>This will select the
program that the cursor is on in the list of
programs.
An asterisk (*) will be to the left of the selected
program.
Select Program Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Select Program Button:
When the program you want is highlighted
Press<SELECT PROG>This will select the
program that the cursor is on in the list of
programs.
An asterisk (*) will be to the left of the selected
program.
Send RS232 Button: PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Send RS232 Button:
Press<SEND RS232>
This will transmit the program or programs out the RS232 serial
port.
It will send the program that is highlighted.
It will send All the programs if ALL is
highlighted.
A ‘%’ is sent at the beginning and end of the transmitted string.
Send RS232 Button: PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Send RS232 Button:
It is also possible to send the following via
RS232:Parameters
OffsetsSettings
Macro Variables
Go to the display for the one you want to
transmit andPress
<SEND RS232>
The following Settings effect RS232 Transmission:
Setting 11, 12, 13, 14 and 37.
Receive RS232 Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Receive RS232 Button:
Press<RECV RS232>
This will receive one or more programs from the
RS232 serial port.
Enter a valid program number before pressing
the receive button.
If ALL is highlighted, do not enter a program name. The program
names will be entered automatically.
Receive RS232 Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Receive RS232 Button:
It is also possible to receive the following via
RS232:Parameters
OffsetsSettings
Macro Variables
Go to the display for the one you want to receive
andPress
<RECV RS232>
The following Settings effect RS232 Receive:Setting 11, 12, 13, 14
and 37.
Erase Program Button:
PROGRAM (LIST PROG) O91002 N00000
O00000
O00001 (I.D. Thread Milling)
O00002 (I.D. Thread Milling #2)
O00022 (Program – VQC)
* O00123 (Mill HMC2)
O01234 (G150 SUB PGM)
O08998 (Clipboard)
O08999 (DIR LIST)
O09000 (vvv Probe)
O09023 (REN EASYSET)
O09123 (NC PRO ID)
O09721 (REN X DIAM)
O09722 (REN Y DIAM)
O09723 (REN ACT OFFSET)
O09724 (SETTING)
O09726 (Basic meas –2t)
60 PROGRAMS 67% FREE (681084 BYTES)
ALL TO SEND, RECV, ERASE F1 TO DUP PROG
F2 DISK WR, F3 DISK RD, F4 DIR RD
* O00123 (Mill HMC2)
Erase Program Button:
Press<ERASE PROG>
This will erase the highlighted program, or the program specified in
the input buffer.
If ALL is highlighted all programs will be
erased.