not-goat Instructions 1

Glue

InstructionsYou will need a craft knife or other sharp knife, a pair of scissors, some glue and a glue spreader.

The best type of glue to use is white school glue (PVA.)

Print out the parts sheets onto thin cardboard. Photocopier card is ideal. Notice that the parts pages are marked front and back. Print out a front page, flip it over, then print the back onto the same sheet. Allow the ink to dry completely before continuing.

Before cutting anything out, score along all the dotted lines and cut out any holes with a craft knife. Both these jobs are easier to do on full sheets of card.

Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid lines. Grey areas show where to glue

Cutout

Dashed lines are hill folds

Dotted lines are valley folds

Black lines show where to cut.

Shaded areas show where to glue.

Logic Goats : not-goat

1 2

3

You’ll need a coin about this size

Fold over the two flaps (1-2) so that they are at ninety degrees as shown above and glue them into place.

Glue the box together as shown in the picture. (3-11)

Assemble and glue on the box stiffener. (12-13)

Glue the flaps 1&2 down. Fold round and glue the coin holder to make a little packets. This provides weight

to help the goat move

more positively.

Glue together the push button (14-19) as shown.Glue the coin holder into place in the push button.

Glue the push button into place (20). Make sure

that it moves freely.

not-goat

and-goat

not-goat

not-goat Instructions 2

5

Make sure that the alignment piece is glued into place inside the body, lining it up with the two creases. (26)

Glue the pivot into place on the inside of the body. (27)

Make the two body inners by folding them round and gluing them. (28-29)

Glue the two sides into the body carefully lining up the curved edges. (30-31)

Assemble the four legs. (32)

Glue the four legs to the body. (33)

Glue on top flap of the body end. (34)

pivot

hinge

neck

Glue together the neck (21-22)

Glue together the pivot (23) and glue on the hinge (24)

Glue the hinge to the neck (25)

4

pivot

hinge

Upside downpivot assembly

not-goat Instructions 3

6

Assemble the head and horns. (35-38)

Glue the head to the neck (39-40)

Assemble the pushrod. (41)

Use the pushrod to join the neck and the push button. (42-43)

Glue the feet to the box top (44)

Assemble and glue on the tail.

Glue down the last two flaps of the back piece. (45)

Finally, glue the ears and the eyes into place. Your not-goat is now compete!

1

0

0

1

not-goat

truth table

Logic Goats: not-goat

At the heart of the computer is the logic gate. These microscopically small devices, including the not-gate the and-gate and the or-gate are used to make the computer do its stuff.

Each logic gate has one or more inputs and an output. In the case of the not gate the output turns on only only when inputs are turned off. By wiring these gates together in complex ways devices can be made that add or multiply or play music or predict the weather.

Logic goats work in the same way; though they may not be able to play your music. The goat only nods his head when the button is NOT pressed.

not-goat

not-goat : parts 2

Box Stiffener

no

t-go

at

not-goat

www.flying-pig.co.uk© Rob Ives / Flying Pig 2007

Cut out

Cut out

4444

4444

4444

4444

3 4

9 10

13

8

6 5

7

13

12

Box

no

t-g

oat

not-goat: Sheet 1 Back

4

10 9

3

12

1 1

20

2

2

11

117 8

5 6

not-goat : parts 2

BackBack

31

Left Body Inner Right Body Inner

Coi

n H

olde

r

Push Button

30

3333

3333

28

29

16

15

20

18

17

41

42

Pus

h R

od

43

not-goat: Sheet 2 Back

29

28

14

14

16

15

1817

19

19

43

41

not-goat : parts 3

Top

38 38 37 37

35 35 36

36

39

25

22

42

21

27

24

23

Eyes

Hor

n

Hor

n

Ears

Head

Piv

ot

Nec

k

Hin

ge

Front

not-goat : parts 3

Top

38 38 37 37

35 35 36

36

39

25

22

42

21

27

24

23

Eyes

Hor

n

Hor

n

Ears

Head

Piv

ot

Nec

k

Hin

ge

Front

not-goat: Sheet 3 Front

25

24

37 37 38 38

3636

3535

40

22

23

not-goat : parts 4

Front

Bod

y

Body End

Tail

Legs

Legs

Alignment Piece

32 32

32 32

33 33

33 33

27

34

45

45

not-goat : parts 4

Front

Bod

y

Body End

Tail

Legs

Legs

Alignment Piece

32 32

32 32

33 33

33 33

27

34

45

45

not-goat: Sheet 4 Back

26

3232

3232

44444444

44444444

30

31

26

4545

34