lone wolf climber stands
TRANSCRIPT
-
8/4/2019 Lone Wolf Climber Stands
1/22
WARNING! Make sure you have read and understand all instructions.
Practice first at ground level.
Always wear TMA approved fall arrest system when usingany treestand.
Do not use while intoxicated or when taking medications that
cause drowsiness.
Do not attach to rotten, loose bark or dead trees, metal or
utility poles.
Avoid use during wet or icy conditions, or during lightning storms.
Haul gun or bow up from ground after climbing tree. Platform is designed to hold one person only.
Do notjump on platform or seat, nor should you stand on seat.
Do not attempt to alter product in any way.
Maximum load is 350 pounds, except where noted.
Failure to follow these instructions could cause serious injury or death.
WARNING!
You must read and understand all of the following instructions
before first use. If you do not, it could result in serious injury up
to and including death. Any questions please call 309-691-9653.
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
-
8/4/2019 Lone Wolf Climber Stands
2/22
LONE WOLF PORTABLE TREESTANDSPO Box 62
Edwards, IL 61528Phone: (309) 691-9653 Fax: (309) 693-9410
www.lonewolfstands.com
PRODUCT LINE
INSTRUCTIONSMANUAL
-
8/4/2019 Lone Wolf Climber Stands
3/22
1
WARNING! Make sure you have read and understand all instructions.
Practice first at ground level.
Always wear TMA approved fall arrest system when usingany treestand.
Do not use while intoxicated or when taking medications that
cause drowsiness.
Do not attach to rotten, loose bark or dead trees, metal or
utility poles.
Avoid use during wet or icy conditions, or during lightning storms.
Haul gun or bow up from ground after climbing tree. Platform is designed to hold one person only.
Do notjump on platform or seat, nor should you stand on seat.
Do not attempt to alter product in any way.
Maximum load is 350 pounds, except where noted.
Failure to follow these instructions could cause serious injury or death.
WARNING!
You must read and understand all of the following instructions
before first use. If you do not, it could result in serious injury up
to and including death. Any questions please call 309-691-9653.
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
-
8/4/2019 Lone Wolf Climber Stands
4/22
3
Make sure all nuts and bolts are secure before each use.
Replace any worn or damaged parts with components from Lone Wolf.
All bolts for this product are Grade 8.
POLYURETHANE TRACTION BELT
APPLICABLE TO: Alpha Sit & Climb and Alpha Hand Climber
1.) With a permanent marker write date of 1st use on each belt.
2.) Inspect belt before each use
3.) Replace every 5 years or when you observe any of the following:
a.) belt has external cracks or tears visible
b.) any internal cables are broken
c.) any teeth are offset from normal pitch or are torn or cut
Shown is the proper use of the traction
belt for the Lone Wolf Climbers (dia 1). The
polyurethane belts are designed to be used
on the Lone Wolf products only. Always use
your traction in the position that it is shown in
dia 1. Never use the belt in this position (dia. 2).
Use in this position can cause damage to the
traction belt. WARNING: Point of arrow marks
the end of the belt (dia. 2a). No part of the
arrow should be showing after the cams are
engaged (dia. 1a). Any failure to follow the
instructions may cause belt to disengage
and cam to open.
General Maintenance
POLYESTER WEB BELTS
APPLICABLE TO: Alpha Ladder Stand, Climbing Sticks, Elite Hang on, Alpha Hang On,
Assault Hang On, and Assassin Platform, Pro Series Hang On & Climbing Sticks
1.) Inspect belts before each use
2.) Replace every 5 years or every year if left out yearly
3.) Replace belts if you observe any of the following:a.) cut or worn webbing
b.) buckles are bent or cam release is binding
c.) stitching is loose, cut, or becoming unraveled
4.) With a permanent marker write the date of the 1st use on each belt
CORRECT INCORRECT
CORRECT INCORRECT
(dia. 1) (dia. 2)
(dia. 1a) (dia. 2a)
-
8/4/2019 Lone Wolf Climber Stands
5/22
27
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Lone Wolf Climbing Stands
(Applicable to the Alpha Hand Climber and Alpha Sit and Climb.Includes: Back Packing straps, Seat Cushion, Bungee Cord,
Stabilizer Straps and 6-Pt Fall Arrest System.)
WARNING! Make sure you have read and understand all instructions.
Practice first at ground level.
Always wear TMA approved fall arrest system when using any treestand.
Do not use while intoxicated or when taking medications that cause drowsiness.
Do not attach
to rotten, loose bark or dead trees, metal or utility poles. Avoid use during wet or icy conditions, or during lightning storms.
Haul gun or bow up from ground after climbing tree.
Platform is designed to hold one person only.
Do notjump on platform or seat, nor should you stand on seat.
Do not attempt to alter product in any way.
Maximum load is 350 pounds, except where noted.
Failure to follow these instructions could cause serious injury or death.
GENERAL MAINTENANCE
Make sure all nuts and bolts are secure before each use.
Replace any worn or damaged parts with components from Lone Wolf.
All bolts for this product are Grade 8.
POLYURETHANE TRACTION BELT
Replace every 5 years. Inspect belts before each use.
Replace belts when you observe any of the following:
a.) Belt has external cracks or tears visible.
b.) Any internal cables are broken.
c.) Any teeth are offset from normal pitch, or are torn or cut.
d.) With permanent markers write date of first use on each belt.
-
8/4/2019 Lone Wolf Climber Stands
6/22
28
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
continued
ALPHA HAND CLIMBER (HCCSH) ALPHA SIT & CLIMB (SACCSH)
Lone Wolf Climbing Stands
POLYURETHANE TRACTION BELT continued
1.) With a permanent marker write date of 1st use on each belt.2.) Inspect belt before each use3.) Replace every 5 years or when you observe any of the following:
a.) belt has external cracks or tears visibleb.) any internal cables are brokenc.) any teeth are offset from normal pitch or are torn or cut
Shown is the proper use of the traction
belt for the Lone Wolf Climbers (dia 1). The
polyurethane belts are designed to be usedon the Lone Wolf products only. Always use
your traction in the position that it is shown in
dia 1. Never use the belt in this position (dia. 2).
Use in this position can cause damage to the
traction belt. WARNING: Point of arrow marks
the end of the belt (dia. 2a). No part of the
arrow should be showing after the cams are
engaged (dia. 1a). Any failure to follow theinstructions may cause belt
to disengage and
cam to open.
CORRECT INCORRECT
CORRECT INCORRECT
(dia. 1) (dia. 2)
(dia. 1a) (dia. 2a)
-
8/4/2019 Lone Wolf Climber Stands
7/22
29
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 3: Pull the cord to the end of the slot.
Cam Tethers
Step 1: Run the tether through the hole
in the end of the cam.
Step 2: Tie the ends together.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
8/22
30
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Stabilizer Strap InstallationClimber SeatAlpha Hand Climber and Alpha Sit and Climb.
Step 1: For the HAND CLIMBER TOP
SECTION take the short end of the sta-
bilizer straps and take it over the casting
in the front corner of the seat through the
sewn loop.
Step 2: Pull tight.
Step 1: For the SIT AND CLIMB TOP
SECTION, wrap the short end of the
strap under the angled support arm at
the location shown. Make sure the sewn
loop is to the outside.
Step 2: Thread the buckle in through
the sewn loop and cinch it up tight.
Rotate the stabilizer buckle so it points
downward.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
9/22
31
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 1: To install the straps on the
STAND BASE thread the long end of the
strap long end of the strap along the
edge frame of the casting just in front of
the brush pocket towards the rear.
Step 2: Run the sewn loop through and
pull tight.
Stabilizer Strap InstallationClimber BaseApplicable to Alpha Hand Climber and Alpha Sit and Climb.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
10/22
32
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 2: Then, push the hinge forward
to the end of the slot.
First, install the climber base.
Step 1: Loosen the torque knobs and
pull the hinge washer inward.
Step 3: Re-tighten the knobs.
Lone Wolf Climber PLATFORM InstallationApplicable to Alpha Hand Climber and Alpha Sit and Climb.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
11/22
33
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 6: Place around the tree. Adjust
the stand platform slightly higher on thefront end.
Step 5: Pull the belt from the tube.
Step 7: Insert the belt back into the
tube. NOTE: WARNING- point of arrowmarks the end of the belt. No part of the
arrow should be showing after the cams
are engaged. Failure to follow these
instructions could cause belt to disengage
and cam to open. Now re-attach the
cams firmly.
Step 4: Unlatch the cam.
continued
Lone Wolf Climbing Stands
Lone Wolf Climber PLATFORM Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.
-
8/4/2019 Lone Wolf Climber Stands
12/22
34
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Lone Wolf Climber TOP SECTION InstallationApplicable to Alpha Hand Climber and Alpha Sit and Climb.
Step 1A: For the HAND CLIMBER flip
the tubes over so they rest on the side of
the seat casting.
Step 1B: For the SIT AND CLIMB,
loosen the torque knobs.
Step 2: Pull the hinge washer inward. Step 3: Push the hinge forward to the
end of the slot.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
13/22
35
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 4: Retighten the knobs. Now, you
are ready to put your top section onto
the tree.
Step 5: Unlatch the cam and pull the
belt from the tube.
Step 6: Place the belt around the tree and insert into the tube.
NOTE: WARNING- Point of arrow marks the end of the belt. No part of the arrow
should be showing after the cams are engaged. Failure to follow the instructions
may cause belt to disengage and cam to open.
Lone Wolf Climber TOP SECTION Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
14/22
36
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 7: Now re-attach your cam firmly. Step 8: Connect your stabilizer straps.
WARNING- the stabilizer straps must be
connected before leaving the ground and
must always remain connected while the
treestand is in use.
Lone Wolf Climber TOP SECTION Installation continuedApplicable to Alpha Hand Climber and Alpha Sit and Climb.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
15/22
37
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Climbing Instructions Alpha Hand Climber
Step 1: Harness to tree. Step 2: Support your weight onto the
climbing aid.
Step 3: Place your feet under the
hinges and the bar as shown. Apply
slight pressure to the hinge with the
inside of the foot.
Step 4: Bend at the knees to
disengage stand.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
16/22
Step 5: Keeping one foot under the
hinge bar, step back onto the center of
the stand with the other to secure it in
place.
Step 6: Slide the harness rope up the
tree to the appropriate height.
38
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 5: Keeping one foot under the
hinge bar, step back onto the center of
the stand with the other to secure it in
place.
Step 6: Slide the harness rope up the
tree to the appropriate height.
Step 7: Disengage the climbing aid,
raise, and repeat the process.
Step 8: When you reach your desiredheight or when the platform becomes
level, adjust your harness rope height
to it is tight while in a sitting position.
Now while in a sitting position pull your
stabilizing straps tight.
Climbing Instructions Alpha Hand Climber continued
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
17/22
39
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Climbing Instructions Alpha Sit & Climb
Step 1: Step into center of from. Attach
harness rope to tree and lift into postion
to climb.
Step 2: Distribute your weight onto
climbing aid. Place feet under hinge and
bar as shown. NOTE: Flip foam seat pad
over one time, this will hold the seat in
upright position.
Step 3: Apply slight pressure to hinge
with inside of foot. Bend at knees to
disengage stand.
Step 4: Pull stand up with legs. Re-
engage stand by shifting weight to heels.
Slide harness rope up tree to appropriate
height. Stand up and repeat process.
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
18/22
40
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 1: Fold the stand and seat down
flat placing the two bolt heads into the
stabilizer channel as shown.
Step 2: Lay the top section of the Hand
Climber on top of the platform.
Step 3: Install the bungee cord and stabilizer straps as shown.
Alpha Hand Climber Back Packing Instructions
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
19/22
41
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 4: Criss cross stab straps. Step 5: This is the proper position for
the Hand Climber to be back packed.
Alpha Hand Climber Back Packing Instructions continued
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
20/22
42
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 1: The traction belts should be
retracted into the tubes as far as possi-
ble with the cams in the locked position.
Step 2: Fold the top and bottom flat
and place the top upside down.
Step 3: Place the Sit and Climb bar
between the teeth and traction belt.
Step 4: Lay the bar on 2 points of the
teeth.
Alpha Sit and Climb Back Packing Instructions
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
21/22
43
ALWAYS WEAR A TMA APPROVED FALL ARREST
SYSTEM WHEN USING ANY TREESTAND
If you do not understand any of these instructions,
please call Customer Service (309-691-9653) or
visit our web site (www.lonewolfstands.com)
Step 8: This is the proper position for
back packing the Sit and Climb.
Step 5: Install the bungee cord and
stabilizer straps as shown.
Step 7: Criss-cross and connect the
stabilizer straps. Pull them tight.
Alpha Sit and Climb Back Packing Instructions continued
continued
Lone Wolf Climbing Stands
-
8/4/2019 Lone Wolf Climber Stands
22/22
62
For written and video instructions
please visit www.lonewolfstands.com
See the latest from Lone Wolf
at www.lonewolfstands.com
The Wolf PackLone Wolf Quiver and
Quiver Stand Mount
Wolf Jaws Combo Silent Tote