lovejoy engineering data
DESCRIPTION
Lovejoy EngeneeringTRANSCRIPT
ED-1
Engineering Data
ED
Engineering Data
ED-2
ED
A Brief Tutorial on Misalignment The function of a coupling is to connect driving and driven equipment. Inaddition, a coupling serves to protect costly equipment from the effects ofmisalignment, shock loads, vibration and shaft end float. Of these fac-tors, the most common is misalignment and end float (also known asaxial misalignment).
Misalignment is a condition created by two shafts whose axes are not inthe same straight line. There are three forms of misalignment: parallel,angular, or the combination of the two. End float is the relative motion oftwo shaft ends.
Parallel misalignment occurs when the axes of the connected shafts areparallel, but not in the same straight line (fig. 1). Angular misalignmentoccurs when the axes of the shafts intersect at the center point of thecoupling (fig. 2). End float occurs when one shaft moves along it’s axisrelative to the other shaft. (fig. 3)
Misalignment can result from a combination of manufacturing tolerances,poor installation practices, thermal growth or shrinkage, foundation move-ment, and/or component wear. The combination of angular and parallelmisalignment within a system may be more detrimental to the couplingand equipment than either of the individual misalignment. Axial misalign-ment- result of either thrust loads, reaction loads, or heat generatedmovement - compounds the problem. Understanding the amount of mis-alignment that the coupling must handle or installing a coupling where itexceeds a maximum rated misalignment can result in premature couplingfailure and/or significant equipment damage.
Misalignment and Coupling FailureThe life expectancy of a coupling is affected by the degree of misalign-ment. The larger the misalignment, the shorter the life of the coupling asshown in fig.5. Misalignment may causes heat generation, fatigue, andan increase in wear in bearings of the drive and driven components.
P.T. Basics
PARALLEL MISALIGNMENTFIGURE 1
ANGULAR MISALIGNMENTFIGURE 2
AXIAL MISALIGNMENTFIGURE 3
COMPOSITE RADIAL MISALIGNMENTFIGURE 4
LIFE VERSUS MISALIGNMENT
FIGURE 5
WARNINGYou must refer to page iv for Important Safety Instructions and Precautions forthe selection and use of these products. Failure to follow the instructions andprecautions can result in severe injury or death.
!
Worked exampleCalculate the worst possible composite alignment misalignment when:
α1 max = ±0.4ºα2 max = ±0.4º
L max = 3 in. L max = 75 mm (LH and RH shafts)P1 max = 0.008 in. P1 max = 0.2 mmP2 max = 0.008 in. P2 max = 0.2 mm
1. Worst possible angular misalignment (Fig. 1) = α1 + α2
= 0.4º +0.4º= 0.8º
2. Maximum radial misalignment (Fig. 2) = R1 + R2
Since α1 and α2 are equal, R1 = R2
Calculate for 2(R1) = 2 (tan α1 x L)= 2 (tan α1 x L) = 2 (tan 0.4 x 75)= 2 (tan 0.4 x 3) = 2 (0.007 x 75)= 2 (0.007 x 3) = 1.05 mm= 0.042 in.
3. Maximum parallel misalignment P3 (Fig. 3)= √P12 + P22
= √0.0082 + 0.0082 = √0.22 + 0.22
= 0.0113 inches = 0.28 mm4. Worst possible misalignment (Fig. 4) RC = R1 + R2 + P3
= 0.042 + 0.0113 = 1.05 + 0.28= 0.0533 in. = 1.33 mm
Note: How relatively minor angular misalignments can produce dispropor-tionate radial misalignments. In this example, they account forapproximately 80% of the worst possible composite misalignment.
ED-3
Engineering Data
ED
When Misalignment Can Not be MeasuredWhen it is not possible to measure the misalignment of a system, or indesigning a new system, the following method can be used to estimateangular, parallel and combined misalignment. Each type of misalignment isfirst calculated and then the results are combined.
To calculate the maximum angular misalignment, the distance (L) and angle(α) must be known or estimated (see example below). First, calculate theangular misalignment noting the critical plane or midpoint of the shaft ends.Second, using the maximum parallel misalignment, be sure to considerboth horizontal and vertical directions (Fig.3). Maximum parallel misalign-ment occurs when the shafts are diagonally opposed. Third, combine theresults.
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
Summary
Worst possible angular misalignment = α1 + α2 (Fig. 1)Maximum radial misalignment = R1 + R2 (Fig. 2)Maximum parallel misalignment √(P12 + P22) = P3 (Fig. 3)Worst possible composite radial misalignment RC = R1 + R2 + P3 (Fig. 4)
Figures 1 through 4 represent that α1 = α2 and P1 = P2, and that L is the same for LH and RH shafts.
P.T. Basics
HorsepowerOne HP is the rate of work required to raise 33,000 pounds one foot inone minute.
Force x FPM Torque (in pound-inches) x RPMHP = ————————— HP = ——————————————
33,000 63,025
Torque (in pound-feet) x RPMHP = ———————————————
5,252
FPM = Feet per minute
RPM = Revolutions per minute
Horsepower per Hundred RPMWhen the HP is given and the RPM, N, is known, HP/C is:
HP x 100HP/C = —————
N
Once HP/C is known, HP @ N RPM is found by HP=HP/C x N
KilowattsOne KW is the rate of work required to raise 11,163 kg 0.305 meter in oneminute.
TorqueThe twisting or turning effort around a shaft tending to cause rotation.Torque is determined by multiplying the applied force by the distance fromthe point where force is applied to the shaft center.
ConversionsKW x 1.341 = HPHP x 0.7457 = KWNm x 0.737562 = ft-lbNm x 8.85 = in-lbft-lb x 1.356 = Nmin-lb x 0.113 = NmHP x 550 = ft-lb/sec
Engineering Data
ED-4
ED
Formulas and Equations
Nm x RPMKW = ————————
9,550
Example:15 HP @ 1750 RPM is:
15 x 100HP/C = ————— = .85 HP per 100 RPM (HP/C)
1750
Using .85 HP/C, the HP rating @ 800 RPM is:
.85—— x 800 = .85 x 8 = 6.8 HP100
TQ = F (force) x R (radius)
Inch example:20 HP at 100 RPM = 12,605 pound-inches Torque
63,025 x HPTorque (in-lb) = ————————
RPM
= Force x Lever Arm (in inches)
5,252 x HPTorque (ft-lb) = ————————
RPM
= Force x Lever Arm (in feet)Force = Working load in pounds
Lever Arm = Distance from the force to the center of rotation in inches or feet.
Metric example:10 KW at 100 RPM = 955 Nm:
KW x 9,550Torque (Nm) = ———————
RPM
Force = Working load in NewtonsLever Arm = Distance from the Force to the center of rotation in millimeters.
Overview
ED-5
Engineering Data
ED
Overhung LoadsAn overhung load is a bending force imposed on a shaft due to the torquetransmitted by V-drives, chain drives and other power transmissiondevices, other than flexible couplings.
Most motor and reducer manufacturers list the maximum values allowablefor overhung loads. These values should be compared with the load actu-ally imposed by the connected drive.
Weights of the drive components are usually negligible. The formulas arebased on the assumption that the load is applied at a point equal to oneshaft diameter from the bearing face. Factor F, shown at right, depends onthe type of drive used.
Inch example:Find the overhung load imposed on a reducer by a double chain drivetransmitting 7 HP @ 30 RPM. The pitch diameter of the sprocket is 10 in.;service factor is 1.3.
Solution:
(63,025) (7 x 1.3) (1.25)O.H.L = ——————————————— = 4,779.4 lbs.
(30) (5)
Metric example:Find the overhung load imposed on a reducer by a double chain drivetransmitting 10 KW @ 30 RPM. The pitch diameter of the sprocket is 254 mm; service factor is 1.3.
Solution:
(376) (10 x 1.3) (1.25)O.H.L = ————————————— = 160 N
(30) (1.27)
1.00 for single chain drives1.10 for timing belt drives
F = 1.25 for spur or helical gear or double chain drives1.50 for V-belt drives2.50 for flat belt drives
63,025 x HP x FO.H.L. = —————————————
N x R
HP = Transmitted HP x service factorN = RPM of shaftR = Radius of sprocket, pulley, etc.F = Factor
376 x KW x FO.H.L. = —————————
N x R
KW = Transmitted KW x service factorN = RPM of shaftR = Radius of sprocket, pulley, etc. (mm)F = Factor
Overview
Formulas and Equations
Engineering Data
ED-6
ED
HPSpeed
Torque(RPM)
Constant Increases DecreasesConstant Decreases IncreasesIncreases Constant IncreasesDecreases Constant DecreasesIncreases Increases ConstantDecreases Decreases Constant
Horsepower/Speed/Torque RelationshipsFormulas and Equations
Electrical Formulas
To Find Single-phase Three-phase To FindAlternating or Direct
CurrentAlternating Current
Amperes when horsepower is known
Amperes whenkilowatts are known
Amperes whenKva are known
Kva
Horsepower = (Output)
KW x 1,000E x pf
HP x 7461.73 x E x Eff x pf
KW x 1,0001.73 x E x pf
Kva x 1,0001.73 x E
ER
IR
EI
Amperes when voltageand resistance are known
Voltage when resistanceand current are known
Resistance when voltageand current are known
Kva x 1,000E
I x E x pf1,000
Kilowatts1.73 x I x E x pf
1,000
I x E1,000
1.73 x I x E1,000
I x E x Eff x pf746
1.73 x I x E x Eff x pf746
General Information (Approximation)(All values at 100% load)At 1,800 RPM, a motor develops 36 in-lb per HP.At 1,200 RPM, a motor develops 54 in-lb per HP.At 575 volts, a three-phase motor draws 1 amp per HP.At 460 volts, a three-phase motor draws 1.25 amp per HP.At 230 volts, a three-phase motor draws 2.5 amp per HP.At 230 volts, a single-phase motor draws 5 amp per HP.At 115 volts, a single-phase motor draws 10 amp per HP.
Temperature conversionDeg. C = (Deg. F - 32) x 5/9
Deg. F = (Deg. C x 9/5) + 32
I = Amperes; E = Volts; Eff = Efficiency; pf = power factor; Kva = Kilovolt amperes;KW = Kilowatts; R = Ohms
HP x 746E x Eff x pf
Alt. CurrentSingle-Phase
Motor Amps @ Full Load1
HP Three-Phase
DC HP Single-Phase
Three-Phase
DCAlt. Current
HPAlt. Current
Single-Phase
Three-Phase
DC HP Single-Phase
Three-Phase
Alt. CurrentDC
—————
—————
180240300360480
268355443534712
Note: 1. Values are for all speeds and frequencies @ 230volts.Amperage other than 230 volts can be figured:
V =230 x Amp from Table
New Voltage
Example:
For 60 HP, three-phase @ 550 volts:(230 x 150)
= 62 amps550
Power factor estimated @ 80 percent for most motors. Efficiency is usually80 to 90 percent.
4.98.0
10.012.017.0
2.03.44.86.28.6
2.74.86.68.5
12.5
571/2
101520
284050——
14.421.026.038.050.0
2029385674
2530405060
6075
100120150
92110146180215
75100125150200
Overview
↑ ↓ ↓ ↑↑ ↑↓ ↓↑ ↑ ↓ ↓
1/2
111/2
23
ED-7
Engineering Data
ED
Trigonomic FormulasAngles and sides of right angle triangles
Hypotenuse x SineHypotenuse / CosecantSide adjacent x TangentSide adjacent / Cotangent
Hypotenuse x CosineHypotenuse / SecantSide opposite x CotangentSide opposite / Tangent
Side opposite x CosecantSide opposite / SineSide adjacent x SecantSide adjacent / cosine
Formulas for findingfunctions of angles
Formulas for finding sides of right tri-angles with an angle and side known
To find length of
opposite side
To findlength of
hypotenuse
To findlength of
adjacent side
Trigonomic Formulas
TriangleArea = Base x 1/2 perpendicular height
SphereArea of surface = Square of diameter x 3.1416Volume = Cube of diameter x 0.5236
CubeArea of surface = Square of side x 6Volume = Cube of sideDiagonal = Side x 1.732
CylinderArea of curved surface = Diameter x length x 3.1416Volume = Square of diameter x length x 0.7854
ConeArea of curved surface = Base diameter x slant height x 1.5708Volume = Base diameter squared x perpendicular height x 0.2618
(Or: Area of base x 1/3 perpendicular height)
CircleArea = Square of diameter x 0.7854 (Or: Square of radius x3.1416)Circumference = Diameter x 3.1416Diameter = Circumference x 0.3183Doubling diameter increases area four times; tripling diameterincreases area nine times, etc.
SquareArea = Square of sideDiagonal = Side x 1.4142Side = Diagonal x 0.7071
Square inscribed in circleSide of square = Diameter of circle x 0.7071
(Or: Circumference of circle x 0.2251)Diameter of circle = Side of square x 1.4142Circumference of circle = Side of square x 4.4429
Square and circle with equal areaSide of square = Diameter of circle x 0.8862Diameter of circle = Side of square x 1.128Circumference of circle = Side of square x 3.545
RectangleArea = Length x widthDiagonal = Square root of width2 + length2
Side opposite = Sine
HypotenuseSide adjacent
= CosineHypotenuseSide opposite
= TangentSide adjacentSide adjacent
= CotangentSide oppositeHypotenuse
= SecantSide adjacentHypotenuse
= CosecantSide opposite
Overview
a
a
a
a
a
b
b
b
b
b
c
c
c
c
c
—c
Sine Cc
Cosine Bb
Sine Bb
Cosine C—a
Cosecant Ba
Secant Cc
Cotangent Bc
Tangent C—a
Secant Ba
Cosecant Cb
Tangent Bb
Cotangent C
√ b2 + c2
c x Cosecant C
c x Secant B
b x Cosecant B
b x Secant C
a2 - c2
a x Sine B
a x Cosine C
c x Tangent B
c x Cotangent C
a2 - b2
a x Cosine B
a x Sine C
b x Cotangent B
b x Tangent C
Formulas
To find angles To find sides
To findc
= Sine Cab
= Cosine Cac
= Tangent Cbb
= Cotangent Cca
= Secant Cba
= Cosecant Ccb
= Sine Bac
= Cosine Bab
= Tangent Bcc
= Cotangent Bba
= Secant Bca
= Cosecant Bb
Formulas To find
C
C
C
C
C
C
B
B
B
B
B
B
√
√
Engineering Data
ED-8
ED
43,5604,046.85641.562 x 10-3
7633.8985429.9214.69595251.996778.1693.9302 x 10-4
0.252107.5862.9307 x 10-4
1,055.05612.960.02358090.017584317.57690.39370080.01100.013160.446113627.850.193410.061020.00110000.03531,7280.02831680.0370376.2288357.48051928.31684725.714057.8657910.47194740.12467530.062427935.314671.307951264.1721
Multiply by To findGivenTo findMultiply byGiven
AcresAcresAcresAtmospheresAtmospheresAtmospheresAtmospheresBTUBTUBTUBTUBTUBTUBTUBTU / minutesBTU / minutesBTU / minutesBTU / minutesCentimetersCentimetersCentimetersCm of mercuryCm of mercuryCm of mercuryCm of mercuryCm of mercuryCoulombCubic centimeterCubic centimeterCubic centimeterCubic centimeterCubic feetCubic feetCubic feetCubic feetCubic feetCubic feetCubic feetCubic feet/hourCubic feet/hourCubic feet/minuteCubic feet/poundCubic meterCubic meterCubic meter
Square feetSquare metersSquare milesCm of mercuryFeet of waterInches of mercuryPounds/square inchCalorieFoot-pounds-forceHorsepower-hoursKilogram-caloriesKilogram-metersKilowatt-hoursJouleFoot-pounds/secondHorsepowerKilowattsWattsInchesMetersMillimetersAtmospheresFeet of waterKg/square meterPounds/square footPounds/square inchAmpere-secondCubic inchesLiterCubic millimeterCubic feetCubic inchesCubic metersCubic yardGallons (British)Gallons (U.S.)LitersQuarts (U.S. dry)Cubic cm/secondLiter/minuteGallons (U.S.)/sec.Cubic meter/kilogramCubic feetCubic yardsGallons (U.S.)
Conversion Tables and Charts
Cubic meterCubic yardsCubic yardsCubic yardsCubic yards/minutesCubic yards/minutesDegreeDegree/secondFathomFeet of waterFeet of waterFeet of waterFeet of waterFeet of waterFeet/minuteFeet/minuteFeet/minuteFeet/minuteFeet/minuteFeet/secondFeet/secondFeet/secondFeet/secondFeet/secondFeet/secondFerkin (U.S.)FootFootFootFoot-poundsFoot-pounds-forceFoot-pounds-forceFoot-pounds-forceFoot-pounds-forceFoot-pounds-forceFoot-pounds/minuteFoot-pounds/minuteFoot-pounds/minuteFoot-pounds/minuteFoot-pounds/secondFoot-pounds/secondFoot-pounds/secondGallon (British)Gallon (British)Gallons (U.S.)/minute
1,000270.7645548201.9740.453.3662340.0174530.16666760.02950.8826304.862.430.43350.5080.016670.018290.30480.0113630.481.0970.592118.290.68180.01136930.48120.30481.3561.286 x 10-3
5.050 x 10-7
1.355820.13830.766 x 10-5
1.286 x 10-3
0.016673.03 x 10-4
2.26 x 10-5
7.717 x 10-2
1.818 x 10-3
1.3558189.6326190.27276548.020834
LiterCubic feetCubic meterGallons (U.S.)Cubic feet/secondGallons (U.S.)/sec.RadianRevolution/minuteFeetAtmospheresInches of mercuryKilograms/sq. meterPounds/square footPounds/square inchCentimeter/secondFeet/secondKilometers/hourMeters/minuteMiles/hourCentimeters/secondKilometers/hourKnotsMeters/minuteMiles/hourMiles/minuteGallons (U.S.)CentimeterInchMeterNewtoNmeterBTUHorsepower-hoursJoulesKilogram-metersKilowatt-hoursBTU/minuteFoot-pounds/secondHorsepowerKilowattsBTU/minuteHorsepowerWattsCubic feet/hourCubic meter/hourCubic feet/hour
ED-9
Engineering Data
ED
Multiply by To findGivenTo findMultiply byGiven
Gallons (U.S.)/minuteGallon (dry)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons (liquid)Gallons waterGallons water/minuteGallons—ImperialGallons—U.S.Gallons (U.S.)/minuteGallons (U.S.)/minuteGallons (U.S.)/minuteGramsGramsGramsGramsGrams (troy)Grams/centimeterGrams/cubic cmGrams/cubic cmGrams/literGrams/literGrams/literHorsepowerHorsepowerHorsepowerHorsepowerHorsepowerHorsepowerHorsepower (boiler)Horsepower (boiler)Horsepower-hoursHorsepower-hoursHorsepower-hoursHorsepower-hoursInchInches of mercuryInches of mercuryInches of mercuryInches of mercury
0.2271247268.80253,785.4120.13368052314.951 x 10-3
0.83267423.785412848.34536.00861.200950.832672.228 x 10-3
8.0208340.0630810-3
0.03527390.032152.205 x 10-3
2.0833 x 10-3
5.6 x 10-3
62.430.036138.3450.0624271,00042.407233,0005501.0140.7457745.733,4799.80952,5471.98 x 106
2.737 x 105
0.745725.40.033421.133345.370.73
Cubic meter/hourCubic inchCubic centimetersCubic feetCubic inchesCubic yardsGallons (British)LitersPints (liquid)Quarts (liquid)Pounds of waterTons of water/24 hrs.Gallons—U.S.Gallons—ImperialCubic feet/secondCubic feet/hourLiters/secondKilogramsOuncesOunces (troy)PoundsOunces (troy)Pounds/inchPounds/cubic footPounds/cubic inchPounds/1,000 gallonsPounds/cubic footParts/millionBTU/minuteFoot-pounds/minuteFoot-pounds/secondHorsepower (metric)KilowattsWattsBTU/hourKilowattBTUFoot-poundsKilogram-metersKilowatt-hoursMillimetersAtmospheresFeet of waterKilograms/sq. meterPounds/square foot
Inches of mercuryInches of waterInches of waterInches of waterInches of waterInches of waterInches of waterInch-poundsJouleKilogramsKilogramsKilogramsKilogramsKilograms-caloriesKilograms-caloriesKilograms-caloriesKilograms-caloriesKilometersKilometersKilometersKilometersKilometers/hourKilometers/hourKilometers/hourKilometers/hourKilometers/hourKillowatt-hoursKillowatt-hoursKillowatt-hoursKillowatt-hoursKillowatt-hoursKillowatt-hoursKilowattsKilowattsKilowattsKilowattsKilowattsKilowattsKnotsLeague (statute)Light yearLitersLitersLitersLiters
0.49120.0024580.0735525.40.57815.2020.036130.112980.0009489.812.20462261.102 x 10-3
103
3.96830861.558 x 10-3
1.162 x 10-3
3,280.84103
0.62137121,09454.680.91130.5399616.670.62143,4152.655 x 106
1.3413.6 x 106
860.53.67 x 105
56.86944,253.7737.61.3410214.3308103
1.15077935.8785 x 1012
103
0.0353161.0210-3
Conversion Tables and Charts
Pounds/square inchAtmospheresInches of mercuryKilograms/sq. meterOunces/square inchPounds/square footPounds/square inchNewtoNmetersBTUNewtonsPoundsTons (short)GramsBTUFoot-poundsHorsepower-hoursKilowatt-hoursFeetMetersMilesYardsFeet/minuteFeet/secondKnotsMeters/minuteMiles/hourBTUFoot-poundsHorsepower-hoursJouleKilogram-caloriesKilogram-metersBTU/minuteFoot-pounds/minuteFoot-pounds/secondHorsepowerKg-calories/minuteWattsMiles (statute)/hourMiles (statute)MilesCubic centimetersCubic feetCubic inchesCubic meters
Engineering Data
ED-10
ED
Multiply by To findGivenTo findMultiply byGiven
LitersLitersLitersLitersLitersLiters/minuteLiters/minuteLiters/minuteLiters/secondMetersMetersMetersMetersMetersMetersMeters/minuteMeters/minuteMeters/minuteMeters/minuteMeters/minuteMeters/secondMeters/secondMeters/secondMeters/secondMilMilMilesMilesMilesMiles/hourMiles/hourMiles/hourMiles/hourMiles/hourMiles/minuteMiles/minuteMiles/minuteMilligramsMilligrams/literMillilitersMillilitersMillilitersMillimetersMillimetersMinutes (angle)
1.308 x 10-3
0.26422.1130.9081.05675.886 x 10-4
13.198154.403 x 10-3
2.118881003.280839939.3710-3
103
1.0936131.6673.2810.054680.060.037283.2813.60.062.2369360.0010.02545,2801.6091,76044.7881.4670.8689826.822,682881.60910-3
10.06102370.033814210-3
0.10.039372.909 x 10-4
Cubic yardsGallonsPints (liquid)Quarts (dry)Quarts (liquid)Cubic feet/secondGallons (British)/hourGallons/secondCubic feet/minuteCentimetersFeetInchesKilometersMillimetersYardsCentimeters/secondFeet/minuteFeet/secondKilometers/hourMiles/hourFeet/secondKilometers/hourKilometers/minuteMiles/hourInchMillimeterFeetKilometersYardsCentimeters/secondFeet/minuteFeet/secondKnotsMeters/minuteCentimeters/secondFeet/secondKilometers/minuteGramsParts/millionCubic inchFluid ouncesLitersCenitmetersInchesRadians
NewtoNmeterNewtoNmeterNewtonsOuncesOuncesOuncesOuncesOuncesOunces (fluid)Ounces (fluid)Ounces (fluid)Ounces (fluid)Ounces (troy)Ounces (troy)Ounces (troy)Ounces/square inchParts/millionParts/millionParts/millionPascalPoundsPoundsPoundsPoundsPoundsPoundsPounds of waterPounds of waterPounds of waterPounds of water/min.Pounds (troy)Pounds (troy)Pounds (troy)Pounds (troy)Pounds (troy)Pounds (troy)Pounds (troy)Pounds/cubic footPounds/cubic footPounds/cubic footPounds/cubic inchPounds/cubic inchPounds/cubic inchPounds/footPounds/inch
0.7375628.850.224810.062528.3495270.91152.79 x 10-5
2.835 x 10-5
1.8050.02957301.0408430.0833331.1034811.097140.06250.05840.070168.3450.0208854160.0005453.59241.2152814.58334.450.0160227.680.11982.67 x 10-4
12373.241770.82285713.16573.6735 x 10-4
4.1143 x 10-4
4.1667 x 10-3
0.0160216.025.787 x 10-4
27.682.768 x 104
1,7281.488178.6
Foot-pound-forceInch-pound-forcePoundsPoundsGramsOunces (troy)Tons (long)Tons (metric)Cubic inchesLitersMillilitersOunces (British fluid)Pounds (troy)GramsOunces (avoir)Pounds/square inchGrains/U.S. gallonGrains/Imperial gal.Pounds/million gal.Pounds-force/sq. ft.OuncesTons (short)GramsPounds (troy)Ounces (troy)NewtonsCubic feetCubic inchesGallonsCubic feet/secondOunces (troy)GramsPounds (avoir)Ounces (avoir)Tons (long)Tons (short)Tons (metric)Grams/cubic cmKgs/cubic meterPounds/cubic inchGrams/cubic cmKgs./cubic meterPounds/cubic footKilograms/meterGrams/centimeter
Conversion Tables and Charts
ED-11
Engineering Data
ED
Multiply by To findTo findMultiply byGiven Given
Pounds/square footPounds/square footPounds/square footPounds/square inchPounds/square inchPounds/square inchPounds/square inchPsiQuarts (dry)Quarts (dry)Quarts (liquid)Quarts (liquid)Quarts (liquid)Quarts (liquid)RadiansRadiansRadians/secondRadians/secondRadians/secondRevolutionsRevolutionsRevolutions/minuteRevolutions/minuteRevolutions/minuteRevolutions/secondRevolutions/secondRevolutions/secondSquare centimetersSquare feetSquare feetSquare feetSquare feetSquare inchesSquare inchesSquare inchesSquare kilometersSquare kilometersSquare kilometersSquare kilometersSquare metersSquare meters
0.016024.8836.945 x 10-3
0.0680462.3072.03602703.1167.2006251.10157.750.94630.83267420.85936757.295783,437.74757.30.15929.5492973606.28360.10470.016673606.2836010-4
1440.09293.587 x 10-3
0.11111 (1/9)6.4526.944 x 10-3
645.210.76 x 106
106
0.38611.196 x 106
10.763.861 x 10-7
Feet of waterKgs/square meterPounds/square inchAtmospheresFeet of waterInches of mercuryKgs/square meterPound-force/sq. inchCubic inchesLitersCubic inchesLiterQuart (British)Quart (dry)DegreesMinutesDegrees/secondRevolutions/secondRevolutions/minuteDegreesRadiansDegrees/secondRadians/secondRevolutions/secondDegrees/secondRadians/secondRevolutions/minuteSquare metersSquare inchesSquare metersSquare milesSquare yardsSquare centimetersSquare feetSquare millimetersSquare feetSquare metersSquare milesSquare yardsSquare feetSquare miles
Square metersSquare milesSquare milesSquare milesSquare millimetersSquare millimetersSquare yardsSquare yardsSquare yardsTemp. (ºC+17.78)Temp. (ºF-32)ThermTons (long)Tons (long)Tons (long)Tons (long)Tons (metric)Tons (metric)Tons (short)Tons (short)Tons (short)Tons (short)Tons (short)Tons (short)Tons (short)WattsWattsWattsWattsWattsWattsWatts-hoursWatts-hoursWatts-hoursWatts-hoursWatts-hoursWatts-hoursWatts-hoursYardsYards
1.19627.88 x 106
2.593.098 x 106
0.011.55 x 10-3
90.83613.228 x 10-7
1.80.55556 (5/9)100,0001,016.04691.0160472,2401.12103
2,2052,00032,000907.184862,430.560.8928729,1660.907180.0569244.260.73761.341 x 10-3
0.0143410-3
3.412142,6551.341 x 10-3
3,6000.8605367.110-3
360.9144
Square yardsSquare feetSquare kilometersSquare yardsSquare centimetersSquare inchesSquare feetSquare metersSquare milesTemperature (ºF)Temperature (ºC)BTUKilogramsTons (metric)PoundsTons (short)KilogramsPoundsPoundsOuncesKilogramsPounds (troy)Tons (long)Ounces (troy)Tons (metric)BTU/minutesFoot-pounds/minuteFoot-pounds/secondHorsepowerKg-calories/minuteKilowattsBTUFoot-pounds-forceHorsepower-hoursJoulesKilogram-caloriesKilogram-metersKilowatt-hoursInchesMeters
Conversion Tables and Charts
Engineering Data
ED-12
ED
.00004
.00039
.00079
.001
.00118
.00157
.00197
.002
.00236
.00276
.003
.00315
.00354
.00394
.004
.005
.006
.007
.00787
.008
.009
.00984
.01
.01181
.01563
.01575
.01969
.02
.02362
.025
.02756
.0295
.03
.03125
.0315
.03543
.03937
.04
.04687
.04724
.05
.05512
.05906
.06
.06250
.06299
.06693
.07
.07087
.075
.07813
.07874
.08
.08661
.09
.09055
.09375
.09843
.1
.10236
.10937
.001
.01
.02
.025
.03
.04
.05
.051
.06
.07
.0762
.08
.09
.1
.1016
.1270
.1524
.1778
.2
.2032
.2286
.25
.254
.3
.3969
.4
.5
.508
.6
.635
.7
.75
.762
.7938
.8
.911.0161.1911.21.271.41.51.5241.58751.61.71.7781.81.9051.984422.0322.22.2862.32.38122.52.542.62.7781
1/64
1/32
3/64
1/16
5/64
3/32
7/64
Decimal mm
Inches
.11811
.1250
.13780
.14063
.150
.15625
.15748
.17188
.1750
.17717
.18750
.19685
.20
.20313
.21654
.21875
.2250
.23438
.23622
.250
.25591
.26563
.275
.27559
.28125
.29528
.29688
.30
.3125
.31496
.32813
.33465
.34375
.350
.35433
.35938
.37402
.375
.39063
.39370
.400
.40625
.41339
.42188
.43307
.43750
.450
.45276
.45313
.46875
.47244
.48438
.49213
.50
.51181
.51563
.53125
.53150
.54688
33.1753.53.57193.8103.968844.36564.4454.54.762555.085.15945.55.55625.7155.953166.35
6.56.74696.98577.14387.57.54067.627.937588.33448.58.73128.8999.12819.59.5259.9219
1010.1610.318810.510.71561111.112511.43011.511.509411.90621212.303112.512.7
1313.096913.493813.513.8906
1/8
9/64
5/32
11/64
3/16
13/64
7/32
15/64
1/4
17/64
9/32
19/64
5/16
21/64
11/32
23/64
3/825/64
13/32
27/64
7/16
29/6415/32
31/64
1/2
33/6417/32
35/64
Fraction Decimal mm
Inches
.550
.55118
.56250
.57087
.57813
.59055
.59375
.600
.60938
.61024
.6250
.62992
.64063
.64961
.650
.65625
.66929
.67188
.68750
.68898
.700
.70313
.70866
.71875
.72835
.73438
.74803
.750
.76563
.76772
.78125
.78740
.79688
.800
.80709
.81250
.82677
.82813
.84375
.84646
.850
.85938
.86614
.875
.88583
.89063
.900
.90551
.90625
.92188
.92520
.93750
.94488
.950
.95313
.96457
.96875
.98425
.984381.00000
13.9701414.287514.514.68441515.081215.2415.478115.515.8751616.271916.516.5116.66881717.065617.462517.517.7817.85941818.256218.518.65311919.050
19.446919.519.84382020.240620.32020.520.63752121.034421.431221.521.59021.82812222.22522.522.621922.8602323.018823.416523.523.81252424.13024.209424.524.60622525.003125.4
9/16
37/64
19/32
39/64
5/8
41/64
21/32
43/6411/16
45/64
23/32
47/64
3/4
49/64
25/32
51/64
13/16
53/6427/32
55/64
7/8
57/64
29/3259/64
15/16
61/64
31/32
63/641
Fraction Decimal mm
Inches
Conversion Tables and ChartsInch-Millimeter Equivalents
Fraction
ED-13
Engineering Data
ED
EPDM NeopreneHytrelUrethaneNBR (“SOX”)Resistance to:
B—AAAAABBACCC——AA—AA
A
C—AACAAAABCB—A
CAAAACAAB—
B (158ºF)B
AAACCCCCCCCCCCCAACCA
C
ACACCCACCBCCAC
CAABBBACCC
A (158ºF)C
BA
A (158ºF)A
B-C (158ºF)BCCCACCCCC
A (158ºF)A (158ºF)
ABA
A-B
A-BC
A-BB-CCBABCBCCBC
CA(158ºF)
BB (158ºF)
A-B (158ºF)B-CA-BCCC
A (212ºF)C
AcetoneAmmonia AnhydrousAmmonium Hydroxide SolutionsASTM oil No. 1ASTM oil No. 3ASTM reference fuel AASTM reference fuel BASTM reference fuel CBenzeneButaneCarbon TetrachlorideChlorobenzeneChloroformChromic Acid 10-50%Dowtherm A or E solventEthyl AlcoholEthylene GlycoFuel OilGasolineGlycerineHydraulic Oils
(Petroleum Based)Hydrochloric Acid, 37%
(cold)Hydrogen Peroxide, 90%Isopropyl AlcoholKeroseneLacquer Solvents (MEK)Lubricating OilsMethyl AlcoholMineral OilNaphthaNitric Acid, 10%NitrobenzenePhenolPhosphoric Acid, 20%Phosphate EstersPickling Solution
(20% Nitric Acid, 4% HP)Soap SolutionsSodium Hydroxide, 20%Stearic AcidSulfuric Acid, up to 50%Sulfuric Acid, 50% to 80%Tannic Acid, 10%TolueneTrichloroethyleneTurpentineWaterXylene
C—CAAAABCACCCC—CAAAA
A
CCBACBCACCCCC—
CABBCCACCAAC
C—CABABCCACCCC—CBCBC
A
C—CBC—CACCCCA—
CABACC—CCC—C
Legend: A = Fluid has little or no effect; B = Fluid has minor to moderate effect; C = Fluid has severe effect; — = No data availableSleeve and Flexible Element Chemical Resistance Chart
Engineering Data
ED-14
ED
TKeyway
Metric Clearance-fit Bore and Keyway Standards
Max.Min.Max.
9.10010.50011.50012.90013.90016.40017.40018.40019.40021.90022.90024.90027.50028.50031.50033.50035.50038.50041.50043.50045.50049.00052.00054.00056.50059.50062.50064.60066.60069.60073.10077.10080.10083.60085.60087.60090.60093.60095.60097.600
100.600104.600106.600108.600111.600114.600116.600
9.00010.40011.40012.80013.80016.30017.30018.30019.30021.80022.80024.80027.30028.30031.30033.30035.30038.30041.30043.30045.30048.80051.80053.80056.30059.30062.30064.40066.40069.40072.90076.90079.90083.40085.40087.40090.40093.40095.40097.400
100.400104.400106.400108.400111.400114.400116.400
2.01253.01253.01254.01504.01505.01505.01505.01505.01506.01506.01506.01508.01808.01808.01808.0180
10.018010.018010.018012.021512.021514.021514.021514.021516.021516.021516.021518.021518.021518.021520.026020.026020.026022.026022.026022.026022.026025.026025.026025.026025.026028.026028.026028.026028.026028.026028.0260
1.98752.98752.98753.98503.98504.98504.98504.98504.98505.98505.98505.98507.98207.98207.98207.98209.98209.98209.9820
11.978511.978513.978513.978513.978515.978515.978515.978517.978517.978517.978519.974019.974019.974021.974021.974021.974021.974024.974024.974024.974024.974027.974027.974027.974027.974027.974027.9740
8.0159.015
10.01511.01812.01814.01815.01816.01817.01819.02120.02122.02124.02125.02128.02130.02132.02535.02538.02540.02542.02545.02548.02550.02552.03055.03058.03060.03062.03065.03068.03072.03075.03078.03080.03082.03585.03588.03590.03592.03595.03598.035
100.035102.035105.035108.035110.035
8.0009.000
10.00011.00012.00014.00015.00016.00017.00019.00020.00022.00024.00025.00028.00030.00032.00035.00038.00040.00042.00045.00048.00050.00052.00055.00058.00060.00062.00065.00068.00072.00075.00078.00080.00082.00085.00088.00090.00092.00095.00098.000
100.000102.000105.000108.000110.000
11.41.41.81.82.32.32.32.32.82.82.83.33.33.33.33.33.33.33.33.33.83.83.84.34.34.34.44.44.44.94.94.95.45.45.45.45.45.45.45.46.46.46.46.46.46.4
2334455556668888
10101012121414141616161818182020202222222225252525282828282828
Bore Tolerances per DIN 7154, H7; Keyway Tolerances per DIN 6885, Js9
Boremm Min.Max.Min.
Heightmm
Keywaymm
Bore
89
10111214151617192022242528303235384042454850525558606265687275788082858890929598
100102105108110
ED-15
Engineering Data
ED
10 3 1.4 9.976 9.989 2.9875 3.0125 11.400 11.50011 4 1.8 10.971 10.991 3.9850 4.0150 12.800 12.90012 4 1.8 11.971 11.989 3.9850 4.0150 13.800 13.90014 5 2.3 13.971 13.989 4.9850 5.0150 16.300 16.40016 5 2.3 15.971 15.989 4.9850 5.0150 18.300 18.40018 6 2.8 17.971 17.989 5.9850 6.0150 20.800 20.90020 6 2.8 19.965 19.986 5.9850 6.0150 22.800 22.90022 6 2.8 21.965 21.986 5.9850 6.0150 24.800 24.90025 8 3.3 24.965 24.986 7.9820 8.0180 28.300 28.50028 8 3.3 27.965 27.986 7.9820 8.0180 31.300 31.50030 8 3.3 29.965 29.986 7.9820 8.0180 33.300 33.50035 10 3.3 34.958 34.983 9.9820 10.0180 38.300 38.50040 12 3.3 39.958 39.983 11.9785 12.0215 43.300 43.50045 14 3.8 44.958 44.983 13.9785 14.0215 48.800 49.00050 14 3.8 49.958 49.983 13.9785 14.0215 53.800 54.00055 16 4.3 54.949 54.979 15.9785 16.0215 59.300 59.50060 18 4.4 59.949 59.979 17.9785 18.0215 64.400 64.60070 20 4.9 69.949 69.979 19.9740 20.0260 74.900 75.10080 22 5.4 79.949 79.979 21.9740 22.0260 85.400 85.60090 25 5.4 89.941 89.976 24.9740 25.0260 95.400 95.600
100 28 6.4 99.941 99.976 27.9740 28.0260 106.400 106.600110 28 6.4 109.941 109.976 27.9740 28.0260 116.400 116.600120 32 7.4 119.941 119.976 31.9690 32.0310 127.400 127.600140 36 8.4 139.932 139.972 35.9690 36.0310 148.400 148.700160 40 9.4 159.932 159.972 39.9690 40.0310 169.400 169.700180 45 10.4 179.932 179.972 44.9690 45.0310 190.400 190.700200 45 10.4 199.921 199.967 44.9690 45.0310 210.400 210.700220 50 11.4 219.921 219.967 49.9690 50.0310 231.400 231.700250 56 12.4 249.921 249.967 55.9630 56.0370 262.400 262.700280 63 12.4 279.912 279.964 62.9630 63.0370 292.400 292.700300 70 14.4 299.912 299.964 69.9630 70.0370 314.400 314.700350 80 15.4 349.902 349.959 79.9630 80.0370 365.400 365.700400 90 17.4 399.902 399.959 89.9565 90.0435 417.400 417.700450 100 19.5 449.892 449.955 99.9565 100.0435 469.500 469.800500 100 19.5 499.892 499.955 99.9585 100.0435 519.500 519.800
TKeywayBoremm
Heightmm
Keywaymm Max.Min.Max.Min.Max.Min.
Bore
Bore Tolerances per ISO R286, P7; Keyway Tolerances per DIN 6885, JS9Metric Interference-fit Bore and Keyway Standards
Engineering Data
ED-16
ED
Nominal bore diameter
21/16
21/8
23/16
21/4
3.2693.3323.3963.4593.5233.5863.6963.7603.8233.8873.9504.0144.0774.1414.2514.3144.3784.441
Keyway height Reference
“T”-DIM+0.010/-0.000
41/16
41/8
43/16
41/4
45/16
43/8
47/16
41/2
4.5054.5684.6324.6954.7594.8224.8854.949
3/87/161/29/165/8
11/163/4
13/167/8
15/16
111/16
11/8
13/16
11/4
15/16
13/8
17/16
11/2
19/16
15/8
111/16
13/4
113/16
17/8
115/16
2
“T”-DIM+0.010/-0.000
Keyway height Reference
Keyway width+0.002/-0.000
Bore+0.001/-0.000
Nominal bore diameter
U.S. Customary Clearance-fit Bore and Keyway Standards — Core Products
0.37500.43750.50000.56250.62500.68750.75000.81250.87500.93751.00001.06251.12501.18751.25001.31251.37501.43751.50001.56251.62501.68751.75001.81251.87501.93752.0000
0.04690.04690.06250.06250.09380.09380.09380.09380.09380.12500.12500.12500.12500.12500.12500.15630.15630.18750.18750.18750.18750.18750.18750.25000.25000.25000.2500
0.4210.4840.5600.6230.7090.7730.8370.9000.9641.0511.1141.1781.2411.3041.3671.4551.5181.6051.6691.7321.7961.8591.9222.0322.0962.1602.223
0.09380.09380.12500.12500.18750.18750.18750.18750.18750.25000.25000.25000.25000.25000.25000.31250.31250.37500.37500.37500.37500.37500.37500.50000.50000.50000.5000
Nominal bore diameter
Keyway width+0.003/-0.000
Bore+0.0015/-0.000
2.93753.00003.06253.12503.18753.25003.31253.37503.43753.50003.56253.62503.68753.75003.81253.87503.93754.0000
0.75000.75000.75000.75000.75000.75000.87500.87500.87500.87500.87500.87500.87500.87501.00001.00001.00001.0000
0.37500.37500.37500.37500.37500.37500.43750.43750.43750.43750.43750.43750.43750.43750.50000.50000.50000.5000
215/16
331/16
31/8
33/16
31/4
35/16
33/8
37/16
31/2
39/16
35/8
311/16
33/4
313/16
37/8
315/16
4Nominal bore
diameterKeyway width+0.003/-0.000
Keyway height Reference
“T”-DIM+0.010/-0.000
4.06254.12504.18754.25004.31254.37504.43754.5000
0.50000.50000.50000.50000.50000.50000.50000.5000
1.00001.00001.00001.00001.00001.00001.00001.0000
Bore+0.002/-0.000
Bore and Keyway Tolerances per AGMA 9002-A86. Bore Tolerances per AGMA -9002-A86; Keyway tolerances per ANSI B17.1
“T”-DIM+0.010/0.000
Keyway height Reference
Keyway width+0.002/0.000
Bore+0.0015/-0.000
Nominal bore diameter
2.06252.12502.18752.2500
0.50000.50000.50000.5000
0.25000.25000.25000.2500
2.2872.3502.4142.477
“T”-DIM+0.010/-0.000
Keyway height Reference
Keyway width+0.003/-0.000
2.9052.9683.0323.1423.205
25/8
211/16
23/4
213/16
27/8
25/16
23/8
27/16
21/2
29/16
2.62502.68752.75002.81252.8750
0.6250.6250.6250.75000.7500
0.31250.31250.31250.37500.3750
2.31252.37502.43752.50002.5625
0.6250.6250.6250.6250.625
0.31250.31250.31250.31250.3125
2.5872.6512.7142.7782.841
Nominal bore diameter
“T”-DIM+0.010/-0.000
Keyway height Reference
Keyway width+0.004/-0.000
Bore+0.002/-0.000
49/16
45/8
411/16
43/4
413/16
47/8
415/16
551/16
51/8
53/16
51/4
55/16
53/8
57/16
51/2
4.56254.62504.68754.75004.81254.87504.93755.00005.06255.12505.18755.25005.31255.37505.43755.5000
1.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.25001.2500
0.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.62500.6250
5.1055.1695.2335.2965.3605.4245.4875.5515.6145.6785.7415.8055.8685.9315.9956.058
Note: Check the Lovejoy price list for bores and keyways normally stocked at factory or warehouse.
Bore+0.0015/-0.000
ED-17
Engineering Data
ED ED
31/8
31/4
33/8
31/2
35/8
33/4
37/8
441/4
41/2
43/4
551/4
51/2
53/4
661/4
61/2
63/4
7
0.06250.09380.09380.09380.12500.12500.12500.15630.18750.18750.18750.25000.25000.25000.25000.31250.31250.31250.31250.37500.3750
Keyway sizeKeyway size
U.S. Customary Interference-fit Bore and Keyway Standards
Bore BoreActual AGMAinterference
fit
Actual AGMAinterference
fit
Nominalbore
diameter1/25/83/47/8
111/8
11/4
13/8
11/2
15/8
13/4
17/8
221/8
21/4
23/8
21/2
25/8
23/4
27/8
3
0.37500.37500.43750.43750.43750.43750.50000.50000.50000.50000.62500.62500.62500.62500.75000.75000.75000.75000.75000.7500
0.75000.75000.87500.87500.87500.87501.00001.00001.00001.00001.25001.25001.25001.25001.50001.50001.50001.50001.75001.7500
3/4 x 3/83/4 x 3/87/8 x 7/167/8 x 7/167/8 x 7/167/8 x 7/16
1 x 1/2
1 x 1/2
1 x 1/2
1 x 1/2
11/4 x 5/8
11/4 x 5/8
11/4 x 5/8
11/4 x 5/8
11/2 x 3/4
11/2 x 3/4
11/2 x 3/4
11/2 x 3/4
13/4 x 3/4
13/4 x 3/4
3.122/3.12353.247/3.24853.372/3.37353.497/3.49853.622/3.62353.747/3.74853.872/3.87353.997/3.99854.2465/4.2484.4965/4.4984.7465/4.7484.9965/4.9985.246/5.24755.496/5.49755.746/5.74755.996/5.99756.246/6.24756.496/6.49756.746/6.74756.996/6.9975
0.12500.18750.18750.18750.25000.25000.25000.31250.37500.37500.37500.50000.50000.50000.50000.6250.6250.6250.6250.75000.7500
1/8 x 1/163/16 x 3/323/16 x 3/323/16 x 3/321/4 x 1/81/4 x 1/81/4 x 1/8
5/16 x 5/323/8 x 3/163/8 x 3/163/8 x 3/161/2 x 1/41/2 x 1/41/2 x 1/41/2 x 1/45/8 x 5/165/8 x 5/165/8 x 5/165/8 x 5/163/4 x 3/83/4 x 3/8
0.499/0.49950.624/0.62450.749/0.74950.874/0.87450.999/0.99951.124/1.12451.249/1.24951.374/1.37451.499/1.49951.623/1.6241.748/1.7491.873/1.8741.998/1.9992.123/2.1242.248/2.2492.373/2.3742.498/2.4992.623/2.6242.748/2.7492.873/2.8742.998/2.999
Nominal Decimal Nominal Decimal
Nominalbore diame-
ter
Shaft Diameter (inches) Bore DimensionsNominal shaftdiameter less:
Bore ToleranceThruOver
—11/2
34578912
11/23457891220
+.0005-.000+.0010-.000+.0015-.000+.0015-.000+.0015-.000+.002-.000+.002-.000+.002-.000+.0025-.000
23/16 inch bore example:Nominal shaft = 2.1875less .002 + .001 boretotal = 2.1855/2.1865
.001
.002
.003
.0035
.004
.005
.0055
Notes: 1. Consult Lovejoy when considering fits other than these.2. Complies with AGMA 9002-A86 through 9-inch shaft diameter.
There is no industry standard above that.
.006 to .008
.009 to .012
Note: For shaft sizes 1/2� through 61/2�, square keyways are preferred. For shaft sizes over 61/2�, rectangular keyways are preferred.
BORE AND KEYWAY TOLERANCES PER AGMA 9002-A86
Engineering Data
ED-18
ED
63
71
80
90
100
112
132
160
180
200
225
250
280
315
355
HC XXADACLTSPNMTSPNMLA
—
—
—
—
—
—
—
IECFrame
Foot MountingA B C H
ShaftD E
B5 Flange B14 Face GeneralType
803.150
903.543
1003.937
1003.937125
4.921112
4.409140
5.512114
4.488140
5.512140
5.512178
7.008210
8.26825410241
9.488279
10.984267
10.512305
12.008286
11.260311
12.244311
12.244349
13.740368
14.488419
16.4964061645718500
19.690630
24.800
300
300400
400500
SL
SL
SM
SM
ML
ML
LM
SM
SM
SM
SM
SL
1003.937
1124.409
1254.921
1405.511
1606.300
1907.480
2168.504
25410
27910.984
31812.520
35614.016
40615.984
45717.992
50820
61024
401.570
451.770
501.969
562.205
632.480
702.760
893.504
1084.252
1214.764
1335.236
1495.866
1686.614
1907.485
2168.500
25410
632.480
712.800
803.150
903.543
1003.937
1124.409
1325.197
1606.299
1807.087
2007.874
2258.858
2509.843
28011.025
31512.400
35513.980
230.906
301.181
401.575
501.969
602.362
602.362
803.150
1104.331
1104.331
1104.331
1405.512
1405.512
1706.693
1706.693
1706.693
80.313
80.313
130.500
130.500
140.562
140.562
140.562
200.787
1154.528
1305.118
†1656.496
1656.496
2158.465
2158.465
26510.433
30011.811
30011.811
35013.780
40015.748
953.740
1104.331
1305.118
1305.118
1807.087
1807.087
2309.055
2509.842
2509.842
30011.811
35013.780
1405.512
1606.299
2007.874
2007.874
2509.840
2509.840
30011.811
35013.780
35013.780
40015.748
45017.716
90.354
100.393
110.430
120.472
140.560
140.560
140.560
190.748
190.748
190.748
190.748
30.118
3.50.138
3.50.138
3.50.138
40.160
40.160
40.160
50.200
50.200
752.953
853.347
1003.937
1154.530
1305.108
1305.108
1656.496
2158.465
602.362
702.756
803.150
953.740
1104.331
1104.331
1305.118
1807.087
903.540
1054.130
1204.724
1405.512
1606.299
1606.299
2007.874
2509.840
1194.690
1194.690145d
5.690d145
5.690168d
6.614d168
6.614144d
5.687d
2007.875
2007.875
2439.562
32912.940
39515.560
44117.375
49519.488
52020.472
61624.252
75929.900
75929.900
130.50022d
0.880d18
0.69021d
0.844d22
0.88021d
0.844d22
0.88021d
0.844d
271.062
271.062
271.062
351.375
512.008
632.500
632.500
632.500
632.500
1024
1024
M5
M6
M6
M8
M8
M8
M8
M12
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
110.433
140.551
190.748
240.945
281.102
281.102
381.496
421.654
481.890
552.165
602.362
702.756
803.150
853.346
853.346
IEC Quick Reference Chart
1024
116d4.567d
1024
1164.510130
5.120130
5.120107d
4.250d149
5.875153d
6.060d
1495.875
1877.375
2429.510
33313.120
35914.125
38315.079
45717.992
49719.567
68326.880
68326.880
1214.760136d
5.375d131
5.140149d
5.880d1526
162d6.380d
1736.810165d
6.531d180
7.906239d
9.440d
2148.437
25610.062
32912.940
37214.640
41616.375
48319.016
51320.197
58122.874
68226.840
71928.320
2.50.098
2.50.098
30.118
30.118
3.50.138
3.50.138
3.50.138
40.160
LEGEND
Metric dimensions (millimeters) in bold.Inch dimensions in plain type.
d = DC Motors
1 mm = 0.03937 inches1 inch = 25.40 mm
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
— — — — —
—
—
Note: * indicates that this dimension varies depending upon manufacturer
ED-19
Engineering Data
ED
Note: Drawings represent standard TEFC general purpose motors.Dimensions are for reference only.
IEC Motor Frame Dimensions
Frame
63718090
100112132160180200225250280315355
D G GD
111419242828383748556070808585
8.511
15.52024243342
42.54953
67.5717676
456777889
101112141414
456888
101214161820222222
F
Key and Keyseat Dimensions
Engineering Data
ED-20
ED
42
48
56
56H
143T
145T
182
184
182T
184T
213
215
213T
215T
254U
256U
254T
256T
284U
286U
284T
286T
284TS
286TS
324U
326U
324T
326T
324TS
326TS
364U
365U
364T
365T
364TS
365TS
404U
405U
404T
405T
404TS
405TS
444U
445U
444T
445T
447T
449T
444TS
445TS
447TS
449TS
NEMA Quick Reference Chart—Inch
13/4
21/8
27/16
23/4
33/4
41/4
5
51/2
61/4
7
8
9
111/16
23/4
3
5
4
5
41/2
51/2
41/2
51/2
51/2
7
51/2
7
51/8
10
81/8
10
91/2
11
91/2
11
91/2
11
101/2
12
101/2
12
101/2
12
111/4
121/4
111/4
121/4
111/4
121/4
121/4
133/4
121/4
133/4
121/4
133/4
141/2
161/2
141/2
161/2
20
25
141/2
161/2
20
25
9/32*
11/32*
11/32*
11/32
13/32
13/32
17/32
17/32
21/32
21/32
13/16
13/16
11/2
17/8
27/16
21/8
21/2
211/16
211/16
39/16
39/16
31/2
31/2
37/8
37/8
41/16
41/16
45/16
45/16
51/8
51/8
47/8
47/8
33/8
33/8
57/8
57/8
51/2
51/2
315/16
315/16
63/4
63/4
61/4
61/4
4
4
73/16
73/16
75/16
75/16
41/2
41/2
85/8
85/8
81/2
81/2
815/16
815/16
53/16
53/16
415/16
415/16
5
57/8
67/8
67/8
811/16
101/4
127/8
145/8
161/2
181/2
205/16
227/8
227/8
227/8
227/8
2215/16
2215/16
227/8
227/8
2215/16
2215/16
411/16
511/16
65/8
65/8
77/8
99/16
1215/16
145/8
161/2
181/4
201/8
223/8
223/8
223/8
223/8
233/8
233/8
223/8
223/8
233/4
233/4
3/8
1/2
5/8
7/8
7/8
7/8
11/8
11/8
11/8
11/8
13/8
13/8
13/8
13/8
15/8
15/8
15/8
15/8
17/8
17/8
15/8
15/8
17/8
17/8
21/8
21/8
17/8
17/8
21/8
21/8
23/8
23/8
17/8
17/8
23/8
23/8
27/8
27/8
21/8
21/8
27/8
27/8
33/8
33/8
33/8
33/8
23/8
23/8
23/8
23/8
11/8
11/2
17/8
21/4
21/4
21/4
23/4
23/4
3
3
33/8
33/8
33/4
33/4
4
4
47/8
47/8
45/8
45/8
31/4
31/4
55/8
55/8
51/4
51/4
33/4
33/4
63/8
63/8
57/8
57/8
33/4
3 3/4
71/8
71/8
71/4
71/4
41/4
41/4
85/8
85/8
81/2
81/2
81/2
81/2
43/4
43/4
43/4
43/4
3/8
1/2
1/2
3/4
3/4
3/4
1
11/2
2
21/2
3
3
4NPT
4NPT
41/32
43/8
5
51/4
57/8
73/8
95/8
131/8
141/8
151/16
18
199/16
199/16
199/16
199/16
2111/16
2111/16
199/16
199/16
2111/16
2111/16
15/16
111/16
21/16
21/8
21/8
21/8
25/8
25/8
23/4
23/4
31/8
31/8
31/2
31/2
33/4
33/4
45/8
45/8
43/8
43/8
3
3
53/8
53/8
5
5
31/2
31/2
61/8
61/8
55/8
55/8
31/2
31/2
67/8
67/8
7
7
4
4
83/8
83/8
81/4
81/4
81/4
81/4
41/2
41/2
41/2
41/2
33/4
33/4
57/8
57/8
57/8
57/8
71/4
71/4
81/2
71/4
9
11
11
11
14
3
3
41/2
41/2
41/2
41/2
81/2
81/2
81/2
81/2
101/2
121/2
121/2
121/2
16
21/16
21/2
23/4
21/4
23/4
31/2
41/4
43/4
51/4
57/8
65/8
71/2
1/8
1/8
1/8
1/8
1/8
1/8
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
1/4
45/8
55/8
61/2
61/2
61/2
61/2
9
9
9
10
111/4
133/8
133/8
137/8
163/4
19/16
21/4
21/4
21/4
23/8
23/4
—
—
—
—
—
—
1/4-201/4-20
3/8-16
3/8-16
3/8-163/8-161/2-131/2-13
1/2-13
1/2-13
1/2-13
5/8-11
5/8-11
5/8-11
5/8-11
D E 2FNEMAFrame
P U VH N O AA AB AH AJ AK BA BB BD XO TAP
25/8
3
31/2
31/2
41/2
51/4
61/4
7
8
9
10
11
Note: * indicates Slot
ED-21
Engineering Data
ED
D
SFLATFLAT
3/163/161/45/163/81/21/25/85/83/47/8
1
NEMA Motor Frame Dimensions
NEMAShaft
Keyseat Dimensions
U3/81/25/87/8
11/8
13/8
15/8
17/8
21/8
23/8
21/2
27/8
33/8
37/8
R21/6429/6433/6449/6463/64
1 13/64
1 13/32
119/32
127/32
21/64
23/16
229/64
27/8
35/16
NEMA C-Face BA Dimensions143-5TC182-4TC213-5TC254-6TC
23/4
31/2
41/4
43/4
5000Frame BAAAVUPOED AB
5007S5007L5009S5009L5011S5011L
81/2
81/2
81/2
81/2
81/2
81/2
267/8
267/8
267/8
267/8
267/8
267/8
4-NPT4-NPT4-NPT4-NPT4-NPT4-NPT
61/2
11 1/8
61/2
111/8
61/2
111/8
21/2
37/8
21/2
37/8
21/2
37/8
303030303030
2627/32
2627/32
2627/32
2627/32
2627/32
2627/32
101010101010
121/2
121/2
121/2
121/2
121/2
121/2
222228283636
2F15/1615/1615/1615/1615/1615/16
H BA31/8
31/8
31/2
41/4
43/4
51/4
57/8
65/8
71/2
81/2
Frame E F N U V66203204224225254284324326364365404405444445504505
41/8
5
51/2
61/4
7
8
9
10
11
121/2
21/2
23/4
31/4
33/8
33/4
41/8
43/4
51/4
655/8
61/8
61/8
67/8
71/4
81/4
89
215/16
4
41/2
551/2
61/4
7
8
9
10
21/4
27/16
31/4
37/16
41/4
53/8
55/8
63/8
71/8
85/8
3/4
3/4
1
11/8
11/4
15/8
178/83
21/8
23/8
27/8
21/4
2
3
33/8
33/4
47/8
53/8
61/8
67/8
83/8
Note: Drawings represent standard TEFC general purpose motors.Dimensions are for reference only.
Frames Prior to 1963
Engineering Data
ED-22
ED