lt-949 mir-65 installation instructions
TRANSCRIPT
-
7/31/2019 LT-949 MIR-65 Installation Instructions
1/2
TECHNICAL SUPPORTNorth America
Tel: (888) Mircom5(888) 647-2665
InternationalTel: (905) 647-2665
Canada - Head Ofce25 Interchange Way, Vaughan, Ontario, L4K 5W3
Tel: (905) 660-4655, Fax: (905) 660-4113
USA
4575 Witmer Industrial Estates, Niagara Falls, NY 14305Tel Toll Free: (888) 660-4655, Fax Toll Free: (888) 660-4113
Website: www.mircom.com
4 1
MIR-65 Series Smoke & Heat DetectorsInstallation Instructions
GeneralThese instructions apply to the 6 E-Z Fit base, part no MSB-65B, for installingMIR-65 Series smoke and heat detectors.
InstallationThese products must be installed in accordance with the applicable NFPA standards,local codes and jurisdictional authorities. Failure to follow these instructionsmay result in failure of the detectors to report an alarm condition. Mircom is notresponsible for detectors which are improperly installed, maintained and tested.
Before installing these products check the continuity, polarity and insulationresistance of all wiring. Check that siting is in accordance with the re systemdrawings and conforms to all applicable local codes such as NFPA 72.
Use 3 octagonal box for direct connection to the base. 4 octagonal and 4 square
boxes may be used with proper UL listed mounting brackets. When mounting ona wall, install 4 to 12 from the ceiling. Use 3M Weatherban 606 Non-Flammablesealing compound (or equivalent) to seal eld wiring conduit opening in the electricalbox, this will reduce the stacking effect. Secure the base to the electrical box withappropriate screws. Do not overtighten the screws. The raised mark on the side ofthe base indicates the direction of the detector LED when tted. Connect the shield, ifrequired, to the SHIELD terminal on the base.
LT-949 Rev.2September 2010
39214-244/Issue 1
-
7/31/2019 LT-949 MIR-65 Installation Instructions
2/2
2 3
Fig 1. Wiring diagram of MIR-65 Series zone
Fig 2. Wiring diagram of MIR-65 Series zone with common remote indicator
From control panel
L2
L1 IN
R
L1OUT
L2
L1 IN
R
L1OUT
L2
L1 IN
R
L1OUT End-of-linedevice
Remote LED
+
SHIELD SHIELD SHIELD
L1 INR
L1OUT
L2
L1 INR
L1OUT
L2
L1 INR
L1OUT End-of-linedevice
From control panel
L2
+
SHIELD SHIELD SHIELD
Remote LED
Warning
CAUTION: Do not use looped wire under terminal L2. Break wire run to providesupervision of connections.
The above instructions cover the following base model:
MSB-65B 6 E-Z Fit base
Technical Data
Detector model # MHD-65-135, MHD-65-200 MID-65I MPD-65P
Detector type Heat Rate-of-Rise/FixedTemperature
Ionization Photoelectric
Working voltage 933V dc 933V dc 933V dc
Maximum alarm
current
17mA at 9V, 52mA at 24V 17mA at 9V,
52mA at 24V
17mA at 9V,
52mA at 24VSurge current 0mA 0mA 0mA
Supervisorycurrent
4050A at 9V, 4555A at 24V 4050A at 9V,4555A at 24V
4050A at 9V,4555A at 24V
Heat elementrating
MHD-65-135 Ordinary(135F/57C)
N/A N/A
MHD-65-200 Intermediate(200F/93C)
Control panel UL/ULC Listed Compatible Control Panel
Test method Magnet or hair dryer Magnet orGemini 501
Magnet orGemini 501
Installationtemperature
Minimum 32F (0C) Maximumat least 20F (11C) belowrating
Minimum 32F(0C) Maximum158F (70C)
Minimum 32F(0C) Maximum140F (60C)
Control Panel Compatibility
For details of compatible control panels, please contact Mircom directly.
Performing the Magnet Test
Place the magnet near the detector on the OPPOSITE side of the LED.
Fig 3. Performing a magnet test on the MIR-65 series detectors.
LED
PLACE MAGNET HERE