lt_2_2012_llg_uk_op

Labortops 2/2012

Valid until 31.08.2012

Cuvettes/Calibration standards 2

Measuring beakers/Glassware 3

Measuring jugs/Jars 4

Pipetting-Finnpipettes 5

Pipetting-Electrical pipette pumps 6

Recirculating coolers 7

Sampling/Sample preparation 8

Occupational safety 9

Safety in the laboratory 10

Skin protection/Cleaning/

Waste disposal

11

Safety storage cabinets 12

Rotary evaporators 13

Distillation/Vacuum technique 14

Balances/Moisture analysers 15

Life Science-Electrophoresis 16-17

Stirring/Shaking 18

Consumables 19-20

Cuvettes/Calibration standards 2

For more articles see our Laboratory Catalogue from page 1057onwards

With certified calibration standards it’s simply measuring with the utmost confidence. In the long run spectrophotometers will only provide correct results if theyare calibrated regularly. With liquid and glass filter calibration standards from the accredited Hellma Analytics Calibration Laboratory, the traceability ofcalibrations carried out to references of the NIST (National Institute of Standards and Technology) is ensured.

Advantages:- Reliability and comparability of measurement results- Increase of your quality of work and regulation conformity- High process transparency- Simple compliance with quality requirements e.g. ISO 9000, GLP, GMP or the most important Pharmacopoeias (EP, DAB, USP)

Check for stray light

Type Description Wave-length

PK Cat. No.

nm

667.100-UV667-UV1667-UV12

Calibration set according to European Pharmacopoeia, contains filter UV1, UV12Liquid filter UV1, Potassium chlorideReference filter UV12, purified water

198 - 385-

111

6.228 1849.190 9819.190 982

Check for spectral resolution

667.200-UV667-UV6667-UV9

Calibration set according to European Pharmacopoeia, contains filter UV6, UV9Liquid filter UV6, Toluene in n-hexaneReference filter UV9, n-hexane

266, 269-

111

6.240 5359.190 9836.231 555

Check for photometric accuracy

667.305-UV

667-UV60667-UV600667-UV14666-F7666-F2666-F3666-F4

Calibration set according to European Pharmacopoeia, contains filter UV60, UV600, UV14Liquid filter UV60, Potassium dichromate 60mg/lLiquid filter UV600, Potassium dichromate 600mg/lReference filter UV14, Perchloric acidGlass filter F7, DidymiumNeutral density glass filter F2, 0.25 absorbanceNeutral density glass filter F3, 0.5 absorbanceNeutral density glass filter F4, 1.0 absorbance

235 - 350430-270 - 340440 - 635440 - 635440 - 635

1

1111111

7.626 372

6.240 0399.190 9846.240 0407.612 4866.801 8676.801 3326.801 868

Check the wavelength accuracy

667-UV5666-F1666-F7

Liquid filter UV5, Holmium oxide in Perchloric acidGlass filter F1, Holmium oxideGlass filter F7, Didymium

240 - 650279 - 638329 - 875

111

6.227 6666.201 0677.612 486

The new generation of cuvettes with clearly improved,photometric properties. The new optimised shape and narrow wallthickness of the cuvettes provides increased heat transferresulting in more constant sample temperatures duringphotometric measuremens.

- Glass clear polystyrene (PS), cavity sorted- Applicable wavelength range 340nm to 900nm- Very low variation of extinction values- Excellent optical transmission range- Path length 10mm- Overall dimensions 12.5mm x 12.5mm x 45mm- Styrofoam racks: 100 cuvettes in a styrofoam box with cover

Description Capacity PK Cat. No.

ml

MacroSemi-micro

4.01.6

100100

9.406 0119.406 012

Holds up to 12 cells with a 10mm light path. Rack features a hingedlid with secure clasp and a removable insert for easy cleaning. Theheight of the lid will accommodate the tallest of spectrophotometercells, even those with covers or stoppers (maximum 51mm).Stackable. Autoclavable.

Length Width Height PK Cat. No.

mm mm mm

115 121 60 1 9.406 451

Secondary standards for calibrating spectrophotometers

Cell rack, PP

LLG-Disposable plastic cells

L A B W A R E

®

Measuring beakers/Glassware3

For more articles see our Laboratory Catalogue from page 10,36, 75 onwards

Stackable. Highly transparent. Printed blue graduations. Food-safe (suitable for contact with foodstuff in accordance with Regulation EC No. 10/2011).

Capacity Grad. Dia. Height PK Cat. No.

ml ml mm mm

250500100020003000

510102050

75100125148170

115140167212242

11111

9.275 7389.275 7409.275 7429.275 7449.275 746

Highly transparent, with moulded blue graduations. Food-safe (suitable for contact with foodstuff in accordance with Regulation EC No. 10/2011).

Capacity Grad. Dia. Height PK Cat. No.

ml ml mm mm

501002505001000200030005000

22510102050100

40507091

116150170210

7080

120133170215242270

11111111

9.275 7729.275 7739.275 7489.275 7759.275 7769.275 7779.275 7789.275 779

Borosilicate glass 3.3. DIN 168 - 1. EN ISO 4796-1.With graduations and retrace code, pouring ring, PP screw cap and ISO thread.Batch certificate available on request.

Capacity Ext.dia.

Height Neck thread PK Cat. No.

ml mm mm GL

10025050010002000

567086

101136

105143182230260

4545454545

1010101010

9.072 3319.072 3329.072 3349.072 3359.072 336

9.072 334

With short stem. Cone angle of 60°. Standard borosilicate funnels with a highheat stability. All funnels have a cone angle of 60° and therefore offer anoptimum fit for all filter sizes.

Funneldia.

PK Cat. No.

mm

6080100

111

9.251 2019.251 2029.251 203

NEW: Now with Retrace Code

LLG-Funnel, borosilicate glass

Laboratory bottles with retrace code,Borosilicate glass 3.3.

Measuring jugs with handle, PP, mouldedblue graduations

Measuring jugs with handle, stackable, PP,blue graduations

L A B W A R E

®

Measuring jugs/Jars 4

For more articles see our Laboratory Catalogue from page 23,843 onwards

High and low form. Highly transparent. With moulded graduations. Ring marksat the major graduation points. Tolerances of class B acc. to DIN 12681/ ISO6706. The measuring cylinders withstand exposure to temperatures up to80°C without permanent loss of tolerance. Food-safe (suitable for contact withfoodstuff in accordance with Regulation EC No. 10/2011).

Tall form, highly transparent, with blue graduations, hexagonal base,calibrated to contain "In". Tolerances class B according to DIN 12681/ISO6706. Exposure to temperatures above 60°C may effect accuracy. Cleaning up to max. 60°C is recommended to preserve marks and inscriptions.

Capacity Tolerance Height PK Cat. No.

ml ± ml mm

1025501002505001000

0.1000.2500.5000.5001.0002.5005.000

135160195240320380465

1111111

9.274 0809.274 0819.274 0829.274 0839.274 0849.274 0859.274 086

Tall form, hexagonal base

Capacity Grad. Height Tolerance Dia. PK Cat. No.

ml ml mm ± ml mm

10255010025050010002000

0.200.501.001.002.005.0010.0020.00

145170200250315360440482

0.20.51.01.02.05.0

10.020.0

1522273344586997

11111111

7.075 0319.274 4209.274 4289.274 4389.274 4489.274 4549.274 4629.274 464

Low form

25501002505001000

0.501.002.005.0010.0020.00

122142163192218285

0.501.002.005.00

10.0020.00

222737516778

111111

9.274 8209.274 8289.274 8389.274 8489.274 8549.274 862

Cylindrical. Very durable. Stackable. Non-toxic. Suitable for cold storage roomsand refrigerators. Autoclavable - remove cap before autoclaving.

Capacity Screw capdia.

Colour PK Cat. No.

ml mm

153060125250500

3843537070

120

transparenttransparenttransparenttransparenttransparenttransparent

111111

9.033 1819.033 1829.033 1839.033 1849.033 1859.033 186

Multi-purpose, Polystyrene jar without cap.Please order cap separately.

Capacity Dia. Height PK Cat. No.

ml mm mm

12.520.030.050.0

27272741

29416049

1111

9.402 0129.402 0209.402 0309.402 050

Forjars

PK Cat. No.

ml

12.5 / 20 / 3050

11

9.402 2129.402 250

Measuring cylinders, PP, class B, mouldedgraduations

Graduated cylinders, PP, class B, bluegraduated, tall form, hexagonal base

1

2

3

1

2

3 Lids, PE for multi-purpose jars, PS

Multi-purpose jars, PS

Jars with screw cap, PC

Pipetting-Finnpipettes5


includes everything you need for "Good Laboratory pipetting"!- Ergonomic pipettes- Convenient pipette stands- Compatible Thermo Scientific Finntip Flex tips- Disposable reservoirs + Finntip Sample Pack- F-series pen + product brochure- Good Laboratory Pipetting Guide

- Index-Finger Operation- Intuitive Programming- Multilingual user interface- 2 year warranty with web registration

Description PK Cat. No.

- Antimicrobial surface- Adjustable finger rest- Set and forget volume adjustment- 5 year warranty with web registration


Finnpipette F1 GLP Kit 1 incl. 1-10/10-100/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip RackFinnpipette F1 GLP Kit 2 incl. 0.2-2/2-20/20-200/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip RackFinnpipette F1 GLP Kit 3 incl. 10-100µl/100-1000µl/1-10ml pipettes, 1x Finn pipette stand, 3x Finntip RackFinnpipette F1 GLP Kit 4 incl. 2-20/20-200/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip Rack

1

1

1

1

9.282 605

9.282 606

9.282 607

9.282 608

- Light and ultra comfortable pipetting- Improved accuracy and precision- Fully autoclavable- 5 year warranty with web registration


Finnpipette F2 GLP Kit 1 incl. 1-10/10-100/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip RackFinnpipette F2 GLP Kit 2 incl. 0.2-2/2-20/20-200/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip RackFinnpipette F2 GLP Kit 3 incl. 10-100µl/100-1000µl/1-10ml pipettes,1x Finn pipette stand, 3x Finntip RackFinnpipette F2 GLP Kit 4 incl. 2-20/20-200/100-1000µl pipettes,1x Finn pipette stand, 3x Finntip Rack

1

1

1

1

9.282 610

9.282 611

9.282 612

9.282 613

The Thermo Scientific Finntip Flex system offers flexible, soft and sophisticatedhigh-end tips for discerning users. Low attachment and ejection forces due tothe soft tip material. The new rack does not slide on the work bench.- High precision molding with virgin polypropylene- Smooth surface for low liquid retention- Non-slip rack with hinged cover

The Thermo Scientific Finntip 5ml and 10ml is designed to prevent foamingand vortexing, this tip fits into all common sizes of laboratory vessels.

Further volumes and pack sizes available on request.

Type Capacity Description Racks for

PK Cat. No.

µl

Finntip Flex 10Finntip Flex 200Finntip Flex 1000Finntip 5mlFinntip 10ml

0.2-101-200100-10001000-50002000-10000

non-sterilenon-sterilenon-sterilenon-sterilenon-sterile

10x9610x9610x965x545x24

960960960270120

9.282 5119.282 5166.230 7756.053 6026.051 881

9.282 516

6.230 775

6.053 602

6.051 881

Pipette tips Finntip

Finnpipette F2 GLP Kit

9.282 511

Finnpipette F1 GLP Kit

Finnpipette Novus Electronic Pipette

Complete Kits Finnpipette GLP

1 2

1

2

3

3

Finnpipette Novus GLP Kit 1 incl. 10-100/100-1000µl pipette, 2x Novus stand, 2x Finntip Flex-RackFinnpipette Novus GLP Kit 2 incl. 100-1000/500-5000µl pipettes,2x Novus stand, 2x Finntip Flex-RackFinnpipette Novus GLP Kit 3 incl. 1-10/10-100/100-1000µl pipettes,3x Novus stand, 3x Finntip Flex-RackFinnpipette Novus GLP Kit 4 incl. 10-100µl/100-1000µl/1-10ml pipettes,3x Novus stand, 3x Finntip Flex-Rack

1

1

1

1

9.282 600

9.282 601

9.282 602

9.282 603

Pipetting-Electrical pipette pumps 6


This ergonomic pipette controller is lightweight, made from UV resistantmaterial, features adjustable valves and is microprocessor controlled forreliability and accuracy. The powerful pump offers rapid yet sensitive aspirationand dispensing. Filling and dispensing speed is easily set using the same handby pressing the large control button. The bright LED display will indicate whichof the three modes has been selected, High, Low or Gravity Mode. The userlabeling area enables customisation, instant recognition and/or taskdesignation. Additional features include hand neutral design, concave paddedtriggers, a 1ml pipette adapter to increase stability of small pipettes, a longlife Li-Ion battery that allows 20 hours of continuous usage, low batteryindicator and two holders as standard

+++ Soft touch triggers+++ Long life, easily changeable rechargeable

battery+++ Sensitive and adjustable aspiration and

dispensing+++ Labeling area for identification

For 1-100ml glass or plastic pipettes

Uses standard 0.45µm hydrophobic filters

Delivered completely with universal voltage, plug faced charger, bench standand magnetic/fixable wall mount. 5 different coloured autoclavable nose pieces as standard included.


LLG-Electrical pipette pump plus*Membrane filter, 0.45µm, PTFE, non-sterile

15

9.281 0419.281 005

*Available from the middle of July

Improved process reliability with functional validation of air-displacementpipettes.The most frequent cause of inaccuracy in piston-operated pipettes is leakage.This arises from damage either to the seals, pistons or tip cones. Often notdetectable by the naked eye, leaks lead to significant volume errors.The BRAND pipette leak tester (PLT unit) for air displacement pipettes findseven the smallest leaks within seconds.

- Limit values for the commercially available single and multichannel pipettesin the volume range 1µl to 10ml are pre-programmed.

- Testing with and without tips- Test results in seconds- Patent pending

According to monitoring of measuring instruments, air-displacement pipettesmust be checked at regular intervals and the results must be compared withthe ISO 8655-2 error limits. However, a calibration certificate only reflects theresults at the time of testing. The time between these calibrations is crucial,since leaks can occur at any time. Well over 80% of pipettes sent in for repairhave leaks and are outside their volume tolerances, even if they do not drip.

While the PLT unit cannot replace regular gravimetric testing, daily pipettechecks can provide a safeguard during the periods between calibrations. Eventhe smallest leaks are detected. Process reliability for the pipettes is thussignificantly improved.

Items supplied:PLT unit (Pipette Leak Testing Unit) including one adapter each for testing air-displacement pipettes with tip (mounted) and without tip, 2 plugs, 3replacement PE filters for the pipette adapters, universal AC adapter, qualitycertificate and operating manual.

Type PK Cat. No.

Pipette Leak Testing Unit 1 4.007 886

LLG-Electrical pipette pump plus

L A B W A R E

®

Pipette Leak Testing Unit (PLT unit)

2 years warranty

The improved performance

Recirculating cooler7


With the Titrette® bottle-top burette, you can titrate quickly and reliably withhighest precision, even in close quarters, with no mains supply needed - in thelab, in production, or in the field.- High accuracy: precise titration within the error limits of Class A for glass

burettes- Smooth-running operation: for sensitive, drop-wise titration- Compact design: light and stable- Easy Handling: no switching between "fill" and "titrate"- Simple maintenance: cleaning and parts replacement right in the lab.- Titrette® SH to determine the acid content of milk and liquid dairy according

to Soxhlet-Henkel (4°SH = 1ml)Smooth operationThe large, easy-grip hand wheels are conveniently easy to turn. With theoptimised gear ratio, you can fill the device quickly and titrate drop-wise withgreat sensitivity.Class? Like Class A!The Titrette® bottle-top burette has an innovative new measuring systemwhich matches the Class A accuracy of glass burettes and, if needed, can offerthe precision of 3 decimal places below 20ml. This is an important feature forusers who need to work within the Class A error limits as with glass burettesaccording to DIN EN ISO 385 (e.g., pharmaceutical work)Lightweight and compact!All components only move within the housing. The compact design and thelight-weight ensure good stability. The titrating tube can be adjustedhorizontally and vertically. This provides flexibility when positioning theinstrument.Items supplied: Titrette® bottle-top burette, conformity certified,performance certificate, telescoping filling tube (170mm to 330mm),recirculation tube, 2 x 1.5V batteries (AAA/UM4/LR03), 3 x PP bottle adapters(GL45/32, GL 45/S40 and GL32/NS 29/32), 2 coloured light shield inspectionwindows, operating manual.

Capacity Accuracy£ ± A%

(max. vol.)

Reproducibility£ ± V%

(max. vol.)

Interface PK Cat. No.

ml

25502550

0.070.060.070.06

0.0250.0200.0250.020

withoutwithoutincl.incl.

1111

9.271 3329.271 3339.271 3349.271 335

- Environmentally friendly operation with low energy consumption- No side vents, instruments can be placed right next to other equipment- All wetted parts made of stainless steel or high grade plastic- Large, bright LED display- Compact design and small foot print- Splash-proof keypad- Drain tap- Easy filling

Due to its high efficiency the F250 is an economic and environmentally friendlyalternative to conventional tap water cooling.

Type Temp. range

Temp.stability

Coolingcapacity kW at

PK Cat. No.

°C ± °C 20/0/-10°C

EcoChiller F250 +5 to +40 5.00 0.25/0.22/0.21 1 9.698 525

Huber thermal fluids have the best possible thermodynamic and environmentalcharacteristics. The correct selection is vitally important and is dependent onthe temperature range. Consideration must be given to the safety standards toensure reliable and safe operation and optimal results. Maximum life of thefluids is also expected.Type Capacity Temp.

rangePK Cat. No.

litres °C

M20.235.20M20.235.20M40.165.10M40.165.10M60.115.05M60.115.05M90.055.03M90.055.03

5105

105

105

10

-20 to +235-20 to +235-40 to +165-40 to +165-60 to +115-60 to +115-90 to +55-90 to +55

11111111

6.306 0786.250 4206.250 2786.304 3786.201 2556.225 2637.615 6616.202 172

Compact Recirculating Cooler F250 EcoChiller

Bottle top burette Titrette®

Thermofluids

Sampling/Sample preparation 8


For sample preparation with easily adjustable paddle system. The BagMixer® isavailable in 3 sizes and blends all sample types prior to their microbialanalysis. Thanks to their unique adjustable paddle system the blendingchamber can be adjusted to the sample volume. Combined with the variablespeed, a higher bacterial recovery rate is achieved. All BagMixer® units arefitted with a timer. Constructed in stainless steel. The fully opening doorenables easy cleaning.

BagMixer® 400 P with stainless steel door.BagMixer® 400 W and 400 CC with see through glass door.

Click & clean® System (only BagMixer® 400 CC): removable and autoclavablepaddles.

All units have a 3-year warranty and life guarantee for shock absorbers andwindow door.

Capacity: 50ml to 400ml

Type Length Width Height PK Cat. No.

mm mm mm

BagMixer® 400 PBagMixer® 400 WBagMixer® 400 CC

390390420

260260260

290290265

111

6.204 5516.224 2879.570 098

Scan 500 colony counter available on request.

These highly resistant bags provide increased safety. The filter bagsautomatically filter the sample during the blending process, withholdingparticles behind the filter.

The BagPage® has a full-width membrane filter.

The BagFilter® P is a non-woven lateral filter and it is sterile.

BagLight® Package: 40 bags of 25 piecesBagFilter® and BagPage® Package: 20 bags of 25 pieces

Type Description PK Cat. No.

BagLight® 400BagFilter® 400 PBagPage® Plus 400

plain bag, 175mm x 300mmside filter bag, 190mm x 300mmfull-size filter bag, 190mm x 300mm

1000500500

9.570 0979.570 0789.570 081

White. For disposable use. Individually packed.

Type Capacity PK Cat. No.

ml

ScoopScoopScoopSpoonSpoonSpoonSpoon

601252501.232.464.9314.79

1111111

9.150 4619.150 4629.150 4639.150 6399.150 6409.150 6419.150 642

Other sampling devices are available on request.

White PP. Length 180mm. Autoclavable at 121°C.

Capacity Width PK Cat. No.

ml mm

1.232.464.9314.79

20253039

1111

9.150 6439.150 6449.150 6459.150 646

Sampling scoops and spoons, PS, sterile

Laboratory mixer, BagMixer®

Sample spoon, PP

TOP price!

Blender bags, BagSystem®

Occupational safety9


- highest safety (certified according EN149)- anatomical design and soft material-edges avoid bruising to the face- compatible with safety spectacles because of the safe optimised nose-area- seamless, continuous headband for comfortable and secure mask fit- innovative shape-optimised design - completely metal free

Respiratory half-mask FFP1- protection against contaminates up to 4 x OEL- easy to differentiate by colour coding (blue - FFP1)

Respiratory half-mask FFP2- protection against contaminates up to 10 x OEL- easy to differentiate by colour coding (orange - FFP2)

Respiratory half-mask FFP 3- protection against contaminates up to 30 x OEL- easy to differentiate by colour coding (black - FFP3)- circulatory venting via the soft edges prevents fogging of safety spectacles

Type Description Colour PK Cat. No.

silv-Air 2220

silv-Air 2100silv-Air 2110silv-Air 2200silv-Air 2210silv-Air 2310

FFP2 with exhale valveand charcoal filterFFP1FFP1 with exhale valveFFP2FFP2 with exhale valveFFP3 with exhale valve

silver

whitewhitewhitewhitewhite

15

2015201515

9.005 754

9.005 7509.005 7519.005 7529.005 7539.005 755

9.005 753

Foldable shape with V-shape-seam for perfect adaption to the facial

structure

Type Description Colour PK Cat. No.

silv-Air 3100silv-Air 3110silv-Air 3200silv-Air 3210silv-Air 3220

silv-Air 3310

FFP 1FFP 1 with exhalation valveFFP 2FFP 2 with exhalation valveFFP 2 with exhalation valve and charcoal filterFFP 3 with exhalation valve

whitewhitewhitewhitesilver

white

3015301515

15

9.005 7569.005 7579.005 7589.005 7599.005 760

9.005 761

9.005 761

Made from PVC with reverse side made of PE. Material thickness: 0.5mm. Side and neck ribbons made of woven plastic fabric and securely attached tothe apron with welded PVC eyelets. Easy to clean, hygienic and dirt-repellentPVC surface. Liquids will not be absorbed but drain off the surface. Machine wash at 60°C. Colour: white. Acc. to 89/686/EWG (Cat. III), EN 467 and EN 14605:2005.

Width Length PK Cat. No.

mm mm

8080100

100120120

111

9.414 4159.414 4179.414 419

- CE approved to EN166 and EN170- Model with sporty and colourful line- High wearability- Moulding nose bridge and temples for maximum comfort- Hypo-allergenic rubber eyebrow protection- Temple adjustable in length- Weight: 30g- Frame colour: black/orange- Lense: clear- Anti-scratch and anti-fog- Protection against UV400

Colour Lens PK Cat. No.

black/orange clear, anti-scratch and anti-fog lens, UV protection

1 9.006 003

Half Masks silv-Air classic

LLG-Safety eyeshields, black/orange

L A B W A R E

®

LLG-Working and chemical protectiveapron Guttasyn®, PVC/PE

Safety in the laboratory 10


PP or PE-LD printed with safety information in accordance with regulation (EC)No. 1272/2008 (GHS) and Vent-Cap screw cap.Dispensing tube with PP tip to optimise the backflow of the medium. The lack of a spray insert and the smooth moulding of the inner tube surfacemake it possible to avoid almost all turbulence in the liquid. Permanent printedlabelling information stating the statutory information required in accordancewith GHS, as well as all important information: quadrilingual chemical name in German, English, French and Spanish, chemical formula, CAS number, hazard pictogram, signal word, hazard statements - H-phrases, precautionarystatements - P-phrases plus NFPA code. PP bottles are autoclavable (at 121°C for 20mins.)

Wide-mouth

Label Capacity Neck thread

Material PK Cat. No.

ml GL

AcetoneAcetoneAcetoneDistilled waterDistilled WaterDistilled waterEthanolEthanolEthanolIsopropanolMethylethylketone (MEK)

250500

1000250500

1000250500

1000500500

4545634545634545634545

PPPPPPPE-LDPE-LDPE-LDPE-LDPE-LDPE-LDPE-LDPP

11111111111

9.223 3759.223 3819.223 3909.223 3709.223 3769.223 3859.223 3749.223 3809.223 3899.223 3789.223 384

Narrow neck

Label Capacity Neck thread

Material PK Cat. No.

ml GL

AcetoneAcetoneAcetoneDistilled waterDistilled waterDistilled waterEthanolEthanolEthanolIsopropanolMethanolMethylethylketone (MEK)

250500

1000250500

1000250500

1000500500500

252532252532252532252525

PPPPPPPE-LDPE-LDPE-LDPE-LDPE-LDPE-LDPE-LDPE-LDPP

111111111111

9.223 3459.223 3519.223 3609.223 3409.223 3469.223 3559.223 3449.223 3509.223 3599.223 3489.223 3479.223 354

Paper with PE backing. Absorbs 750ml/m². With a skid-resistant, waterproof,chemical-resistant polyethylene backing that makes spill containment easy.Thousands of Thirsty Cells™ quickly absorb spills and cushion breakablelabware. Use as a tray, drawer or shelf liner or to wipe up spills.

Type Description Size PK Cat. No.

cm

6205062050620506205062050

Dispenser RollRollDispenser RollRollMat

51 x 915051 x 915051 x 305051 x 4600

51 x 46

1142

350

9.413 3009.413 3016.229 6286.227 8686.802 397

DescProtect is a durable paper which quickly absorbs liquid spills. The PE-coated base layer stops liquids reaching the work surface.

- stays flat, does not ripple or curl to de-stabilise vessels- white surface can be written on using pens or pencils- rapid absorption of liquid spills- excellent fluid protection- no contamination of work surfaces or laboratory cabinets- suitable for school laboratories, wet chemistry, industry

Type Size PK Cat. No.

SheetsSpool

460mm x 570mm400mm x 50m

501

9.160 2709.160 271

With VENT-CAP

VITsafe™ safety wash bottles, PP/PE-LD

Lab Soakers Standard VERSI-DRY®,750ml/m²

LLG-Surface protector DescProtect

L A B W A R E

®

Skin protection/Cleaning/Waste disposal11


Moderately greasy. Particularly suitable for protecting the skin againstorganic solvents, varnishes, oils, petroleum spirit, resins, dyes, paints etc. aswell as for after-work care for dry skin.

Capacity PK Cat. No.

ml

100 1 9.191 148

Quickly absorbed. The cream strengthens the defensive functions of theskin, preventing skin damage from external pollution and soothes irritation.Smooths and cleans without leaving a residue. Using Lindesa® K avoids greasysmears on surfaces and is therefore suitable for workers involved withenamelling, electronics production, or final inspection.


ml

50 1 9.191 149

Non-greasy, quickly absorbed. The cream strengthens the defensivefunctions of the skin, preventing skin damage from external pollution andsoothes irritation. Smooths and cleans without leaving a residue. Lindesa®

gives the skin elasticity and suppleness through its special caring agents. The sense of touch is not affected. For low levels of soiling it providesprotection against weak acids, alkalis and organic substances.


ml

50 1 9.191 145

Constructed from very strong PP film with a broad seam at the bottom. For the disposal of contaminated labware. When autoclaving, the neck of the bag must be left open. Film thickness: 50µm.

Size auto-clavable at


*standard**highly transparent

Crepe paper, adhesive. With heat-sensitive dyes. Colour changes according to DIN EN ISO 11140-1. Rolls of 50M.With Width Figure PK Cat. No.

mm

Steam indicatorHot air indicator

1919

ab

11

9.140 7846.240 223

Lindesa® skin protection cream withbeeswax

Lindesa® K skin protection cream withbeeswax and camomile

Lindesa® O skin protection cream withbeeswax

1

2

3

1

2

3

200 x 300300 x 500400 x 780500 x 780600 x 800600 x 780700 x 1100700 x 1100200 x 300300 x 500400 x 780600 x 800700 x 1100

134 °C134 °C134 °C134 °C134 °C134 °C134 °C134 °C121 °C121 °C121 °C121 °C121 °C

Dispenser box of 100 bags*Box of 500 bags*Box of 250 bags*Box of 250 bags*Box of 100 bags*Box of 250 bags*Box of 250 bags*Box of 75 bags*Dispenser box of 100 bags**Box of 500 bags**Box of 500 bags**Box of 500 bags**Box of 350 bags**

10050025025010025025075

100500500500350

9.404 0999.404 2209.404 2219.404 2229.404 1039.404 2239.404 2249.404 1059.404 0209.404 1009.404 1019.404 1029.404 104

Indicator tape for steam, hot air and gassterilisation

LLG-Disposal bags, PP

L A B W A R E

®

Safety storage cabinets 12


Specifications

External dimensions (WxDxH): 1200 x 615 x 1955mmInternal dimensions (WxDxH): 1050 x 522 x 1645mmWeight: 424kgMax. Loading: 600kgDoor colour: warning yellow, RAL 1004


3 shelves, perforated insert, bottom collection sump 1 7.628 659

7.628 659

Specifications

External dimensions (WxDxH): 600mm x 615mm x 1955mmInternal dimensions (WxDxH): 450mm x 522mm x 1645mmWeight: 265kgMax. Loading: 600kgDoor colour: warning yellow, RAL 1004Door handle: left


3 shelves, perforated insert, bottom collection sump 1 9.840 667

9.840 667

Description Dimensions(W x D x H)

PK Cat. No.

mm

Shelf for VBF.195.60Shelf for VBF.195.120Recirculating air filter systemVentilation system

443 x 435 x 301043 x 435 x 30

1111

9.840 5149.840 5329.840 6509.840 616

9.840 650 9.840 616

Safe and regulation-compliant storage of non-flammable chemicals andpoisons in workrooms

3 cabinet widths, 2 different cabinet heights, 3 door variants, 7 different doorcolours and countless interior fitting variants are available. Please contact us.

- high-grade steel plate body with sturdy, high-quality structured paint finish- 7 different door colours at no extra cost- doors with safety cylinder integrated into the turning handle- prepared for connection (NW 75) to an extraction system on the cabinet’s

ceiling- integrated adjustable feet, easy to align- natural ventilation thanks to vent openings in the floor region- optionally galvanised or painted shelves (RAL 7035 light grey), height

adjustable (grid size 25mm)- watertight, zinc plated bottom collecting sump, optionally included according

to STAWA-R- pull-out drawers with plastic sump

Specifications Type CS.110.105-A

External dimensions (WxDxH): 1055mm x 520mm x 1105mmWeight: 42kgMax. Loading (each shelf): 100kgDesign: wing doors with windowsInterior: 2 zinc-plated shelves, perforated insert,

zinc-plated bottom collection sump

Type PK Cat. No.

CS.110.105-A 1 9.840 680

9.840 680

Fire resistant safety storage cabinetsVBF.195.60/VBF.195.120

Fire resistant safety storage cabinets VBF.195.60

Fire resistant safety storage cabinets VBF.195.120

60cm width = Morespace in the lab

Chemical storage cabinets CS-Classic

Accessories for Safety storage cabinetsVBF.195.60/VBF.195.120

Construction:- Extremely robust construction- Maximum torsional rigidity- Scratch-resistant structured paint finish- Manipulation-proof lock with locking state indicator; integration in locking

system possibleDoors:- The wing doors stop in any position to simplify putting in and taking out of

storage- In case of fire the integrated thermal release guarantees automatic closing of

the doorsBase:- Permanently integrated, drive-under base- Simple transport of the cabinet without pallet- The optionally available base panel seals the base when not in useEquipment:- Various options for individually equipping the cabinet- With the optionally available Q-mover (Cat. No. 9.840 670), even 900mm

and 1200mm wide cabinets can be pushed comfortably through doors in anupright position

Door colour: red, RAL 3020

Rotary evaporators13


With the new RV 10 range of rotary evaporators, IKA® has confirmed that there is always room for improvement, even when it comes to one of the oldestchemical processes: distillation. The RV 10 Rotary Evaporators set new standards for safety, efficiency and ease of use.RV 10 basic standard package includes:- Drive- Heating bath- Vertical glassware, coated and uncoated (1L receiving and distilling flask)- Vapor tube NS 29/32- Vacuum seal- Woulff bottle

Rotary evaporator RV 10 basic- Water/oil heating bath with integrated carrying handles for safe handling- Analog heating bath with adjustable safety circuit, "stand alone" operation is possible, pivoting safety hood as an accessory- Motorized lift (stroke 140mm) with "safety stop" function, if the power cuts out the evaporator flask is automatically lifted out of the heating bath- Adjustable end position recognition to protect the glass from breaking- Speed range from 20rpm to 280rpm. Digital speed display- Rotates clockwise and counterclockwise in interval operation for the drying process- Timer function for time lapse control- Heats up quickly because of optimised bath volumes- Push-off mechanism to loosen tightly fitting flasks- Suitable for DIN EN 12697-3 (Asphalt test for hot asphalt)- 5 year warranty after registration

Rotary evaporator RV 10 digital VSame properties as RV 10 basic, with the following additional functions:- Digital water/oil heating bath with integrated carrying handles, ”stand alone“ operation is possible- Temperature control of the heating bath by a micro controller- Infrared interface for data transfer from the heating bath to the drive unit- RS 232 interface for PC remote operation with labworldsoft® (Cat. No. 9.910 320 - please order separately)

Rotary evaporator RV 10 contolSame properties as RV 10 digital, with the following additional functions:- Integrated vacuum controller with central display for automatic distilling and ramp programming- Integrated solvent library, which can be extended by the user- Programmable volume controlled distillation- Colour graphic display for safe and comfortable operation- Automatic ventilation at the end of each test- Integrated cooling water monitoring- USB interface- New: Now RV 10.4002 Magnetic valve included in delivery


RV 10 basic VRV 10 basic V-CRV 10.70RV 10.8001RV 10 digital VRV 10 contol V

with heating bath HB 10 basic and vertical glassware, RV 10.1with heating bath HB 10 basic and vertical glassware, coated RV 10.10Vapor tube made of borosilicate glass, NS 29/32Lip-seal from a PTFE compound with a built-in stainless steel springwith heating bath HB 10 digital and vertical glassware RV 10.1with heating bath HB 10 control, vertical glassware RV 10.1and RV 10.4002 Magnetic valve laboratory vacuum

111111

6.232 8556.234 5466.237 5354.008 1366.233 5816.234 885

6.232 855 6.233 581 6.234 885

Rotary evaporator

Distillation/Vacuum technique 14

For more articles see our Laboratory Catalogue from page564, 587, 993 onwards

- manufactured from borosilicate glass 3.3 which is resistant to heat andalmost all chemicals.

- meets the highest quality standards according to DIN EN ISO 4797.- reinforced rims are used to prevent breaking during washing and

transportation.

Capacity NS Heightapprox.

Neckdiam.

approx.

Flaskexternal diam.approx.

PK Cat. No.

ml mm mm mm

50501001002505001000200050501001002502505001000

14/2329/3214/2329/3229/3229/3224/2929/3219/2624/2919/2624/2919/2624/2924/2929/32

105105115115145175210260100100110110140140170200

22342234343442342230223022303042

5151646485105131166515164648585105131

1111111111111111

6.236 5086.238 3456.236 3466.236 7746.236 3036.240 4266.237 7026.238 4724.008 3794.008 3804.008 3814.008 3824.008 3834.008 3844.008 3856.242 240

For conical joints, can also be used to secure flasks with ground joints & glass stoppers

- increases the safety of glass vessels; the symmetric, slim and aligned designsolves various application problems of common clips and clamps (can beused with retort clamps)

- secure horizontal and vertical connection with security in the event ofpressure overload

- two-sided handles enable easy mounting and removal- spring steel wire provides long working life and firm grip- will not break or age because of outstanding thermal, chemical and acid

resistance, due to stainless steel AISI 316 Ti, Cr-Ni-Mo 17-12-2- reduced abrasion due to polished surface of material- made in Germany, with production certified according to ISO9001.

Joint size PK Cat. No.

NS

10121419242934404560

5555555555

9.011 4009.011 4019.011 4029.011 4039.011 4049.011 4059.011 4069.011 4079.011 4089.011 409

Versatile vacuum gauge for vacuum measurement between atmosphericpressure and 1 mbar.With integral, alumina ceramic, pressure transducer providing excellentcorrosion resistance and long-term stability.

Specificationen

Measuring range: 1080 to 1mbar (hPa), 810 to 1 TorrMeasurement principle: Capacitive; gas type-independent absolute

pressure measurement

Measuring accuracy: < 1mbar (0.75 Torr) ±1 digitPower supply/battery: 9V Lithium battery/1.2 Ah Ultralife U9VLDimensions (WxDxH): 115mm x 115mm x 66mmWeight: 0.40kg

Type PK Cat. No.

DVR 2 1 9.882 209

LLG-Vacuum measuring instrument DVR 2

L A B W A R E

®

Round bottom flasks, borosilicate glass 3.3

Clipox® NS Clips

Balances/Moisture analysers15


Entry level analytical balance with high-quality single cell weighing system

- Only ACJ: Automatic internal adjustment in the case of a change intemperature > 0.5°C or time-controlled every 4 hours

- Only ACS: Adjusting program CAL, external test weights, please orderseparately

- Large LCD display, digit height 14mm- Dosage aid: High-stability mode and other filter settings can be selected- Simple recipe weighing and documenting with a combined tare/print

function. In addition, the mixing ingredients for the recipe are numberedautomatically and printed out with their corresponding number and weightvalue

- Identification number: 4 numeric positions, printed on calibration protocol- Automatic data output to the PC/printer each time the balance reaches a

steady state- Option: RS 232 C Interface

Single-cell advanced technology:- Fully automatic manufactured weighing cell from one piece of material- Stable temperature behaviour- Short stabilisation time: Steady weight values within approx. 3 sec under

laboratory conditions- Shock proof construction- High corner load performance

Specifications

Readability: 0.1mgReproducibility: 0.2mgLinearity: ±0.3mgOverall dimensions (WxDxH): 210mm x 340mm x 325mmDimensions weighing space (WxDxH): 174mm x 162mm x 227mmDiam. weighing plate: 91mmPermissible ambient temperature: 10°C/30°CNet weight: approx. 6kg


g

ACS 80-4ACS 120-4ACS 220-4ACS 320-4ACJ 120-4MACJ 220-4MACJ 320-4M

80120220320120220320

1111111

9.901 4309.901 4319.901 4329.901 4339.901 4346.253 1716.252 832

Modern moisture analyser with 100 memories and graphic display- Halogen quartz glass heater 400 W- Backlit LCD display, digit height 15mm: Previous drying time, current

temperature, unit for displaying the results, current moisture content in %,drying mode/Status display drying

- Observation window over the sample, useful during initial adjustment- Internal memory for automatic sequence of 10 drying programs and 100

drying processes carried out- The last value measured remains on the display until it is replaced by a new

measurement- Sample description for up to 99 samples, 2 digits, freely programmable, and

is printed in the measuring protocol- Date and time display as standard- 10 sample plates included- Table of applications: There are many practical examples in the operating

instructions

Specifications

Readability: 0.001g/0.01%Weighing range, max: 60gReproducibility, weight of sample 2g: 0.15%Reproducibility, weight of sample 10g: 0.02%Temperature range: +50 to +200°CDimensions (WxDxH): 202mm x 336mm x 157mmType PK Cat. No.

DBS 60-3 1 9.901 441

Aluminium foil, for sample handling with a flanged, crimped wall for rigidity.Finger-tab handle can be etched for identification prior to weighing. Made from oil-free, lightweight aluminium.

Article 6.236 854 is without finger-tab.

Diam. Height PK Cat. No.

mm mm

435770100

1214168

10010010050

6.238 1386.238 1396.238 1406.236 854

6.236 854

Analytical balances type ACS and ACJ

LLG-Aluminium weighing dish

Halogen Moisture Analyser DBS 60-3

L A B W A R E

®

TOP price!

Life Science-Electrophoresis 16


The multiSUB series of Horizontal gel units offers the most versatile solution for DNA and RNA agarose gel electrophoresis currently available.

The tanks are manufactured from one piece and therefore tight for life. They are equipped with high quality platinum electrodes.

High flexibility due to various sizes of gel trays for each tank and different colour coded combs. For gel casting place gel casting dams on the geltrays.

Gel casting dams are included in delivery.

Mini DUO is the smallest unit of the multiSUB series, designed for low tomedium numbers of samples. Very economic due to small buffer volumes.Supplied with MultiSub mini tank, 2x geltrays (7 x 7cm and 7 x 10cm), 2x 8-sample combs, Loading Guides, 1 set of gel casting dams and 1 x 5g bottle ofAgarose.

The MultiSUB Mini Duo-Set includes additionally:- 1 x preparative comb (304µl + Marker, 1.5mm thick)- 1 x combination comb (for multi channel pipettes, 1mm thick)- 1 x analytical comb (16-sample, 1mm thick)- 1 x set of gel casting dams- 10 x Gel Cutting Tips

Type PK Cat. No.

Set MultiSUB Mini Duo 1 7.656 356

The MultiSUB Choice is a versatile tank, designed for a medium number ofsamples.Very flexible due to different geltrays. Supplied with MultiSUB choice Trio tank,3x geltrays (15 x 7cm, 15 x 10cm and 15 x 15cm), 2 x 20-sample combs(1mm), Loading Guides, 1 set of gel casting dams and 1 x 5g bottle ofAgarose.

The MultiSUB Choice Trio-Set includes additionally:- 1 x set of gel casting dams- 1 x preparative comb (743µl + Marker, 1.5mm thick)- 1 x analytical comb (35-sample, 1mm thick)- 1 x combination comb (for multi channel pipettes, 1mm thick)- 10 x Gel Cutting Tips

Type PK Cat. No.

Set MultiSUB Choice Trio 1 7.656 357

Horizontal gel electrophoresis

Set Gel electrophoresis tank MultiSUB Choice Trio

Set Gel electrophoresis tank MultiSUB Mini Duo

Life Science-Electrophoresis17


Cleaver Scientific offers a balanced system for vertical electrophoresis, 2-D electrophoresis and electroblotting.

The tanks are equipped with high quality non-corrisive electrodes and are available in various sizes.

The gel electrophoresis tank OmniPAGE Mini is suitable for parallel treatmentof up to 4 gels with 20 samples each. The tank is easy to handle, especiallyleak proof and guarantees an efficient cooling. For self-cast gels and all majortypes of 8 x 10cm and 10 x 10cm precast gels. Supplied with gelelectrophoresis tank OmniPAGE Mini, 2 sets of glass plates (10 x 10cm)* with1mm spacers, 2 x 1mm 12-sample combs and external casting stand.

The omniPAGE Mini-Set includes additionally:- 1 x 12-sample comb- 2 sets of glass plates (10 x 10cm) with 1mm spacers (1mm). Gel casting and running at the same time. The unit can be upgraded with wet blotting modules.

Type PK Cat. No.

Set omniPAGE TETRAD Mini 1 7.930 246

*The gel electrophoresis tank omniPAGE Mini is compatible with glass plates of other suppliers.

The Cleaver Semi Dry Blotters can be used for all types of blotting: western,southern and northern via uncomplicated buffer and set up procedures and arecompatible with gel thicknesses from 0.25mm up to 10mm. They utilise ascrew down lid, which secures the blot sandwich and allows complete controlof pressure ensuring even transfer. The electrodes, comprising platinum coatedanode and stainless steel cathode, will exhibit practically no corrosion and soprovide many years of trouble free use.

Specifications Mini/Maxi

Unit dimensions (W x L x H): 16 x 16 x 7cm/26 x 26 x 7cmMax. sample capacity: 1 blot, 10 x 10cm/1 blot, 20 x 20cm; 4

blots, 10 x 10cm

Buffer volume: 5ml/20ml


SD10SD20

Semi Dry Mini, 10cm x 10cm SystemSemi Dry Maxi, 20cm x 20cm System

11

9.584 7536.229 381

AG agaroses are suitable for routine analysis of nucleic acids. They combine tensile strength with low electroendosmotic effects to achieve high resolving power for a wide size range of nucleic acid fragments.


g

CSL-AG100CSL-AG500CSL-AG1000

1005002 x 500

111

9.584 6959.584 6969.584 697

Vertical electrophoresis and electroblotting

Agarose for gel electrophoresis

Semi Dry BlottersSet Gel electrophoresis omniPAGE TETRAD Mini

Stirring/Shaking 18


Technical improvements on the trusted RW 20 series design. Robust, slimlineand ergonomic design. With digital display, constant power-drive and hollow-shafted chuck for rotor shaft height adjustment (only when stationary).

incl. R 1826 Plate standincl. R 1342 Propeller stirrerincl. R 182 Boss head clamp

Specifications

Max. stirring volume (H2O): 20LViscosity range: up to 10000mPasMotor rating input/output: 70/35WOutput max. at stirring shaft: 26WSpeed range I (at 50 Hz): 60rpm to 500rpm.Speed range II (at 50 Hz): 240rpm to 2000rpm.Dimensions (WxDxH): 88 x 212 x 294mmWeight: 3.1kgSupply requirements: 230V 50/60 HzMax. stirring shaft torque (at 100rpm.): 150NcmProtection class (DIN EN 60529): IP 20

Dedicated shaker for two or four microtitre plates. Orbital movement.Electronic speed regulation. Acoustic signal at end of timed period. With attachment but without plates.

Specifications

Motor rating input/output: 35/13.2WOrbit: 3mmCapacity: two or four microtitre platesSpeed range: 0rpm to 1100rpmSpeed range: Analogue scaleTimer (digital): 1 to 99 min/ continuousDimensions (WxDxH): 185mm x 320mm x 105mmWeight: 2.7kgHousing IP rating to DIN EN 60529: IP 21Supply requirements: 230V 50/60HzTested to DIN EN IEC 61010-1.

Type PK Cat. No.

MTS 2/4 digital 1 9.838 195

Safety magnetic stirrer with heating, suitable for unsupervised operation

- integrated temperature control- exact temperature and speed setting via digital display, even when switched off- digital display of set safety temperature limit- hot top indicator, hot surface warning to prevent burns, digital error code

display- DIN 12878 connector for attaching a contact thermometer, e.g. ETS-D5 or

PT 1000; enables precise temperature control directly in the heated medium- enhanced safety due to improved heat control technology- highly polished, aluminium hotplate for optimal heat transfer- improved magnetic coupling- supplied with housing protection cover H 98

Type PK Cat. No.

RCT Standard safety control incl. PT 1000 1 9.720 250

Accessories:Electronic contact thermometer ETS-D5, Ikaflon® stirring bars, Trika® stirring bars, RS 1 stirring bar set,RSE Stirring bar remover

Microtitre shaker MTS 2/4 digital

LLG-RCT standard safety control,incl. PT 1000

Type PK Cat. No.

RW 20 digitalRW 20 digital UKRW 20 digital CH

111

6.231 4016.253 8606.253 861

L A B W A R E

®

Package overhead stirrer RW 20 digital

Specifications

Stirring quantity (H2O):Motor rating input/output: 16/9WSpeed display: digitalSpeed range: 50rpm to 1500rpmMax. magnetic bar (L x diam.): 80 x 10mmHeating function

Speed display:Heat output: 600WHeating rate (1 litre H2O in H 15): 6.5K/minTemperature range: RT to 310°CSetting accuracy: ±1KTemp. variation without temp. sensor: ±2KAdjustable safety circuit: 50 to 360°CControl accuracy with sensor: PT 1000/±1KHeating plate

Material:Dimensions: 135mm diam.General data

Dimensions (WxDxH):

20L

digital

aluminium alloy

160 x 270 x 85mm

Weight: 2.5kgProtection class acc. to DIN EN 60529: IP42

Consumables19

For more articles see our Laboratory Catalogue from page 137,161, 214, 716 onwards

Capacity Topdiam.

Bottomdiam.

Fillheight

PK Cat. No.

ml mm mm mm

28110110125280

64809996

114

5156707858

1334252450

10010010010050

9.106 2409.106 2419.106 2429.106 2619.106 263

Self-adhesive. Ø 9.5mm. Printing protected. For labeling of 0.5ml to 2.0mlmicrotubes that contains potentially hazardous substances. The labels haveexcellent heat resistance, chemical resistance and UV resistance and a verygood adhesion to various materials, even on rough or non-polar surfaces suchas on plastics with low surface energy. The material is UL certified. (File MH26760).1000 labels per roll, in dispensing box.


"biohazard" symbol 1000 9.105 740

Provides a smooth writing surface, making labeling easy and fast. Whenmarked tape is advanced and cut off on the serrated edge, a fresh length oflabel tape is positioned on the writing platform. Plastic cutting edge is mouldedinto the housing. Various widths and colours of tape rolls can be mixedtogether on the spindles, which accommodates 5 or more 12mm to 19mmnarrow rolls or 4 x 25mm wide rolls. Spindles are easily removed from the unitfor loading and unloading and can be adjusted to hold either 25mm or 75mmcore diameter rolls.- Includes three plastic separating discs to assure smooth, snag free

dispensing for up to four rolls of tape (additional discs on request).- Moulded-in pen holder wells on the dispenser help to keep writing

instruments handy- Ideal for use with the full line of Write-On™ Tapes, which are available in 6 colors and 3 widths (Laboratory Catalogue page 138).

- Includes mounting holes for secure attachment to a benchtop (screws notincluded). Can also be attached to vertical surfaces using Wall Mount Adapter

Dimensions (WxDxH): 302mm x 143mm x 12mm

Items supplied: Adhesive tape dispenser incl. 1 roll each of 19mm white,red, yellow, green, blue and orange Write-On™ Labeling Tape

Type PK Cat. No.

Write-On™ Economy Set 1 9.040 399

Unique tabs protect your samples from loss and contamination. Place tubes inslots and slide under tabs to keep tubes in place and caps closed when underpressure, floating or submerged. Use in water baths, ice baths or on thebenchtop- Holds up to twelve 1.5ml or 2.0ml microcentrifuge tubes in numbered

locations- Raised handle for easy lifting without agitating samples; stable feet keep

racks upright on the bench- 95mm outer diameter fits most 1000ml beakers- With removable vortexing attachment, this allows samples to be vortexed

simultaneously- Polypropylene construction. Steam autoclavable at 121°C (250°F)

Colour PK Cat. No.

NaturalTurquoisePinkNeon Yellow

1111

9.400 9959.400 9969.400 9979.400 998

Floating racks PrepSafe™ formicrocentrifuge tubes, PP

Set Adhesive tape dispenser Write-On™ Economy

LLG-Labels with "biohazard" symbol

Aluminium containers, round

L A B W A R E

®

PLASTIBRAND®. PP. For all common test tube diameters. Very sturdy design.All openings are widely spaced apart to accommodate screw cap tubes. Allracks have the same footprint and can be stacked easily when empty. ModifiedPP with greater density than water makes them ideal for use in water baths.Large marking area (60mm x 12mm) for barcode labels and alphanumericreferences for clear sample identification. Racks are supplied in three parts forquick and permanent assembly. Continuous use temperature -20 to +90°C.Autoclavable (121°C). Choice of colours as outlined below.Dimensions (L x W): 265mm x 126mm

Array For tubesdia.

Height Colour PK Cat. No.

mm mm

6 x 146 x 146 x 146 x 145 x 115 x 115 x 115 x 115 x 115 x 115 x 115 x 114 x 104 x 104 x 104 x 104 x 84 x 84 x 84 x 83 x 73 x 73 x 73 x 7

131313131616161618181818202020202525252530303030

757575757575757575757575757575758888888888888888

WhiteBlueRedYellowWhiteBlueRedYellowWhiteBlueRedYellowWhiteBlueRedYellowWhiteBlueRedYellowWhiteBlueRedYellow

111111111111111111111111

9.193 2409.193 2419.193 2429.193 2439.193 2309.193 2319.193 2329.193 2339.193 2459.193 2469.193 2479.193 2489.193 2509.193 2519.193 2529.193 2539.193 2559.193 2569.193 2579.193 2589.193 2609.193 2619.193 2629.193 263

Round bottom test tubes made of high quality Fiolax® glass with beaded rim.

Ext.dia.

Length Wallthickness

PK Cat. No.

mm mm mm

81012121416161820

7010075

100130130160180180

0.50.50.50.50.50.60.60.60.6

100100100100100100100100100

7.190 0016.234 0267.613 7957.190 0117.606 3747.606 3757.190 0217.190 0237.190 028

Specialprice

Test tube racks, PLASTIBRAND®, PP

LLG-Test tubes Fiolax® glass

L A B W A R E

®

All prices exclusive VAT or other local taxes. Prices valid until 31. 08. 2012. E & OE.

lt_2_2012_llg_uk_op

Documents

mglliquid filter uv600

uv12liquid filter uv1

uv14liquid filter uv60

uv9liquid filter uv6

mglreference filter

perchloric acidglass

perchloric acidglass

holmium oxideglass filter