lumination cable suspension kit - ge current...kitkit-susp-yokem-semi-xxft (95046985 / 95046986)...
TRANSCRIPT
Installation GuideIND256 | GE2029-8251
BEFORE YOU BEGIN Read these instructions completely and carefully.
WARNING / AVERTISSEMENTRISK OF ELECTRIC SHOCK• Turn power off before inspection, installation or removal.• Properly ground electrical enclosure.
RISK OF FIRE• Follow all NEC and local codes.
RISQUES DE DÉCHARGES ÉLECTRIQUES• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE• Respectez tous les codes NEC et codes locaux.
Lumination® Cable Suspension KitKitKIT-SUSP-YOKEM-SEMI-XXFT (95046985 / 95046986)
120"
6.00 42
GE MountingBracket (Provided with fixture)
Supplied Fastener
#87 Zinc Die CastTerminal
Cable Coupler 1/4-20 Internal Thread
5
1/16” Galvanized7x7 Cable
1
Cross CableGripper
3
Toggle Plate forø1/4”– ø5/16”
Hole
#87 Zinc Die CastTerminal
SL-94-2.04MM-ALAluminum HourglassSleeve
5
*Alternative Ceiling Assembly
ZF-15Z-XC
Alternate Fixture Attachment
Kit Contains:1. Suspension cable -10' (2x)2. Toggled cross-cable (2x)3. Cross-cable gripper (2x)4. M6 bolt (2x)5. 1/4-20 cable coupler (2x)6. Hourglass sleeve (2x)
Lumination® Cable Suspension Kit Installation Guide
2
1 Connect Gripper To Luminaire Mounting SystemThe Lower Mounting Kit is designed to connect either directly to a compatible luminaire or to a mounting bracket included with the luminaire and provide leveling through the adjustment of the cable position.
For luminaires/mounting brackets with dual mounting holes: Connect toggled cross cable as shown and adjust position to level. Ensure M6 bolt is tightened into gripper after levelling.
For mounting brackets with a single central hole: Remove cross cable from gripper and use M6 bolt to attach gripper directly to bracket.
Down Cable
Cross cable gripper
Cross cable
Toggle
Remove cross cable
www.gecurrent.com© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
IND256 (Rev 03/17/20) Enovia - GE2029-8251
Lumination® Cable Suspension Kit Installation Guide
2 Connect Aircraft Cable To Ceiling StructureThe Lower Mounting Kit can connect to the ceiling structure in one of two ways:
Couple to ¼-20 rod: Install aircraft cable through ¼-20 coupler and tighten coupler onto ¼-20 rod attached to building structure. For finished drywall or T-grid ceilings use KIT-MTG-UPR (93026986) to provide ¼-20 thread. Ensure ceiling structure is rated for luminaire load before mounting.
Loop onto structure: Using hourglass sleeve loop aircraft cable over existing building structure and pull tight. Ensure structure is rated for luminaire load before mounting.
Mounting structure provided by others
Hourglass sleeve
T-grid ceiling
Threadedpost providedby othersUnistrut
providedby others
or
3 Attach Aircraft Cable To Gripper And Adjust Height
Pass aircraft cable end through hole at top of cross gripper and pull through until desired level is reached.
Note: Height cannot be adjusted while gripper is under load.
Once mounting brackets are properly levelled luminaires can be installed into brackets according to the specific instructions provided with the luminaire.
Squeeze tip to adjust