lx007 hardware(thai)

Users Manual Fingerprint Identification (Proximity

/ PIN) Access Controller

2

Table of Contents 1. IMPORTANT SAFETY INSTRUCTIONS......................................... 5 2. GENERAL............................................................... 6 3. FEATURES.............................................................. 6 4. SPECIFICATION......................................................... 7 5. IDENTIFYING SUPPLIED PARTS........................................... 10 6. PRODUCT OVERVIEW..................................................... 11 6.1 FEATURES ........................................................... 11 6.2 PRODUCT EXPLANATION .................................................. 14

6.2.1 Panel Description................................................................................................................. 14 6.2.2 Connection Layout ............................................................................................................... 14 6.2.3 Color Coded & Wring Table ................................................................................................. 15

7. INSTALLATION TIPS & CHECK POINT...................................... 16 7.1 CHECK POINTS BEFORE INSTALLATION........................................ 16

7.1.1 Selection of Cable................................................................................................................ 16 7.1.2 Recommended Cable Type and Permissible Length .......................................................... 17

7.2 CHECK POINT DURING INSTALLATION ........................................ 17 7.2.1 Termination Resistor ............................................................................................................ 17 7.2.2 How to Connect Termination Resistors................................................................................ 18 7.2.3 Grounding System for Communication Cable ..................................................................... 18 7.2.4 Reverse Diode Connection.................................................................................................. 19

8. INSTALLATION OF PRODUCT.............................................. 20 8.1 WALL MOUNT (UNIT: MM)................................................ 20 8.2 SYSTEM INITIALIZATION................................................. 20 8.3 WALL MOUNT INSTALLATION ............................................... 21 8.4 WIRING ............................................................. 21

8.4.1 Power Connection................................................................................................................ 21 8.4.2 Input Connection.................................................................................................................. 21 8.4.3 Output Connection............................................................................................................... 23 8.4.4 External Reader Connection................................................................................................ 24

9. COMMUNICATION........................................................ 25 9.1 RS232 COMMUNICATION PORT CONNECTION .................................... 25 9.2 RS485 COMMUNICATION PORT CONNECTION .................................... 25

9.2.1 RS485 Connection (Standalone Unit).................................................................................. 25 9.2.2 RS485 Connection (Multiple Units)...................................................................................... 26

9.3 TCP/IP COMMUNICATION PORT CONNECTION (OPTIONAL).......................... 27 9.4 SERIAL PRINTER CONNECTION ............................................. 28

10. BASIC SETTING....................................................... 29 10.1 INITIALIZATION OF LX007 ............................................. 29 10.2 HOW TO ENTER THE SETUP MENU ......................................... 30 10.3 LANGUAGE SETTING.................................................... 30 10.4 DATE / TIME SETTING................................................. 31 10.5 ID REGISTRATION .................................................... 31

11. OPERATIONS.......................................................... 35

11.1 NORMAL OPERATION.................................................... 35 11.2 DEFAULT SETTING .................................................... 35

12. SETTING CHANGES..................................................... 36 12.1 F1 SETUP MENU .................................................... 37

12.1.1 Language ........................................................................................................................... 38 12.1.2 Date and Time Setting ....................................................................................................... 38 12.1.3 Reader #1 Mode ................................................................................................................ 38 12.1.4 Reader #2 Mode ................................................................................................................ 39 12.1.5 Reader #1 PIN Input .......................................................................................................... 39 12.1.6 Reader #2 PIN Input .......................................................................................................... 39 12.1.7 Communication Address Setting........................................................................................ 39 12.1.8 Baud Rate Setting.............................................................................................................. 40

12.2 F2 SETUP MENU .................................................... 41 12.2.1 Event Memory.................................................................................................................... 42 12.2.2 ID Display........................................................................................................................... 42 12.2.3 Time Unit Setting................................................................................................................ 42 12.2.4 Output T/S + ID.................................................................................................................. 43 12.2.5 Anti-pass Back Mode ......................................................................................................... 44 12.2.6 Duress Mode...................................................................................................................... 44 12.2.7 Wiegand Output ................................................................................................................. 45 12.2.8 Door Open Alarm Time Setting .......................................................................................... 45

12.3 F3 SETUP MENU .................................................... 46 12.3.1 Print Output........................................................................................................................ 46 12.3.2 Voice Volume ..................................................................................................................... 47 12.3.3 Arm/Disarm ........................................................................................................................ 47 12.3.4 Two Men Mode .................................................................................................................. 48 12.3.5 One Time Read.................................................................................................................. 48 12.3.6 Max. User Setup ................................................................................................................ 48 12.3.7 Name Display..................................................................................................................... 49

12.4 F4 SETUP MENU .................................................... 50 12.4.1 Time Schedule ................................................................................................................... 50 12.4.2 Holiday ............................................................................................................................... 51 12.4.3 Holiday Code ..................................................................................................................... 52 12.4.4 Reader#1 Mode Time Schedule ........................................................................................ 52 12.4.5 Reader#2 Mode Time Schedule ........................................................................................ 53 12.4.6 Voice Time Schedule ......................................................................................................... 53

12.5 F5 SETUP MENU .................................................... 54 12.5.1 Exit Button Output Setting ................................................................................................. 55 12.5.2 Door Contact Output Setting.............................................................................................. 56 12.5.3 Aux Input#1 Output Setting................................................................................................ 56 12.5.4 Aux Input#2 Output Setting................................................................................................ 56 12.5.5 Tamper Alarm Output Setting............................................................................................. 56 12.5.6 Cut Off Alarm Output Setting ............................................................................................. 56 12.5.7 Duress Alarm Output Setting ............................................................................................. 56 12.5.8 Arm/Disarm Output Setting ................................................................................................ 56 12.5.9 DR Time Output Setting..................................................................................................... 56 12.5.10 Output Time Schedule Setting......................................................................................... 56 12.5.11 Input Time Schedule Setting ............................................................................................ 56 12.5.12 Cut Off Check Setting ...................................................................................................... 57 12.5.13 Input Type Setting ............................................................................................................ 57

12.6 F6 SETUP MENU .................................................... 58 12.6.1 Output Setting for Reader#1 ID OK Level 1 ...................................................................... 59 12.6.2 Output Setting for Reader#1 ID OK Level 2 ...................................................................... 60 12.6.3 Output Setting for Reader#1 ID OK Level 3 ...................................................................... 60 12.6.4 Output Setting for Reader#1 ID OK Level 4 ...................................................................... 60 12.6.5 Output Setting for Reader#1 ID Error ................................................................................ 60 12.6.6 Output Setting for Reader#1 T/S Error .............................................................................. 60 12.6.7 Output Setting for Reader#1 APB Error............................................................................. 61

12.6.8 Output Setting for Reader#2 ID OK Level 1 ...................................................................... 61 12.6.9 Output Setting for Reader#2 ID OK Level 2 ...................................................................... 61 12.6.10 Output Setting for Reader#2 ID OK Level 3 .................................................................... 61 12.6.11 Output Setting for Reader#2 ID OK Level 4 .................................................................... 61 12.6.12 Output Setting for Reader#2 ID Error .............................................................................. 61 12.6.13 Output Setting for Reader#2 T/S Error ............................................................................ 61 12.6.14 Output Setting for Reader#2 APB Error........................................................................... 61

12.7 F7 SETUP MENU .................................................... 62 12.7.1 ID Registration ................................................................................................................... 62 12.7.2 ID Deletion ......................................................................................................................... 65 12.7.3 ID List................................................................................................................................. 65 12.7.4 Master ID Registration ....................................................................................................... 66 12.7.5 ID Count............................................................................................................................. 67 12.7.6 Event Count ....................................................................................................................... 67

12.8 F8 SETUP MENU .................................................... 68 12.8.1 System Initialize ................................................................................................................. 68 12.8.2 Event Clear ........................................................................................................................ 69 12.8.3 ID Clear.............................................................................................................................. 69 12.8.4 Master ID Clear.................................................................................................................. 69 12.8.5 Time Schedule Clear ......................................................................................................... 70 12.8.6 Default Setting ................................................................................................................... 70

12.9 F9 SETUP MENU .................................................... 71 12.9.1 Version Check.................................................................................................................... 71 12.9.2 Input Test ........................................................................................................................... 72 12.9.3 Output Test......................................................................................................................... 72 12.9.4 LCD Test ............................................................................................................................ 72 12.9.5 Keypad Test ....................................................................................................................... 72 12.9.6 Reader Test........................................................................................................................ 73 12.9.7 Memory Test ...................................................................................................................... 73 12.9.8 Communication Test .......................................................................................................... 73

12.10 F10 SETUP MENU .................................................. 75 12.10.1 Dual Fingerprint Mode ..................................................................................................... 75 12.10.2 Adaptive Mode ................................................................................................................. 76 12.10.3 Identification Mode........................................................................................................... 76 12.10.4 FP Reg. Count ................................................................................................................. 76 12.10.5 Module Version ................................................................................................................ 76

5

1.

Fingerprint Identification (Proximity / PIN) Access Controller,

1.

2.

3. . .

4. .

5. .

, . 6. 7. 8. ; .

.

9. :

a. .

b. .

c. ,. .

d. .

6

2. General IDTECK LX007 / LX007SR . IDTECK LX007 / LX007SR 4 input ports, 2 Form-C relay outputs, 2 TTL outputs, RS232/RS485 communication port optional TCP/IP communication port . 1,000 ( 2,000/4,000 ) 10,000 IDs 20,000 transactions. uploaded MS-Excel, HTML Text format files Time & Attendance management. IDTECK LX007 / LX007SR built-in Fingerprint Module, proximity card IDC 26bit Wiegand 24-key ( 10 , 2 12 function ) . IDTECK LX007 / LX007SR - fingerprint, Proximity Card/PIN / password. IDTECK LX007 / LX007SR 4 external input ports , , a door contact sensor . IDTECK LX007 / LX007SR 2 relay outputs . LCD . Windows-based. IDTECK LX007 / LX007SR stand-alone networked. dual tamper switches - .

3. Features

125KHz(default) Proximity/13.56MHz(optional) Contactless Smart Card,PIN Fingerprint Recognition Access Control Time & Attendance

7

1:1 Verification 1:N Identification 2 Fingerprint Auto Touch Sensor Fingerprint Fingerprint 1,000 / 2,000 / 4,000 Fingerprint Users 10,000/20,000 ID Users / 20,000/10,000 Event Buffers (Selectable) 10 Fingerprint Master IDs Mode Individual IDs 4-Level Door Open Time Individual IDs Time Schedule Individual IDs Input Port, Output Port, Voice Message Reader Mode Network Communication RS232, RS485 built-in TCP/IP 26bit Wiegand Output (34bit LX007SR) Serial Printer Port event ticket Input Cut-off Check User Name & Function Key LCD ARM/DISARM Function Alarm Panel 2 Men Operation Mode Duress Alarm Function Graphic LCD user serial communication Door Phone Function (Optional) Software Selection: STARWATCH TIME PRO 2006, LX ACCESS PRO II 4. Specification

Model LX007 CPU 32bit ARM9, 8bit 16bit Microprocessor

Program Memory 128KByte ROM Fingerprint

Module Data Memory 128KByte / 256KByte / 512KByte Flash Memory

Memory

Controller Program Memory 256KByte ROM

8

Data Memory 512KByte Flash Memory Fingerprint User 1,000 / 2,000 / 4,000 Fingerprint Users Fingerprint Templates 800 Bytes 2 Fingerprint Templates ID User 10,000 / 20,000 Users (Selectable) Event Buffer 20,000 / 10,000 Event Buffers (Selectable)

Passive Type IDK50 / IMC125 : 2

(5cm) IDC80 / IDC170: 4

(10cm)

Active Type IDA150 / IDA200 compatible () 30ms Verification Time 1 . Identification Time 2 . Power / Current DC 12V / Max.650mA

External Reader Port

LX007: 1 Port (26bit Wiegand, 4 / 8bit Burst PIN) Anti-PassBack LX007SR: 1 Port (34bit Wiegand, 4 / 8bit Burst PIN) Anti-PassBack RS232 / RS485 (Max.32ch)

TCP/IP (Internal LAN Converter Required/Optional)

Baud Rate 57,600bps (recommended) / 9,600bps / 19,200bps /38,400bps (selectable)

Input Port 4 Ports (Exit Button, Door Sensor, Aux# 1,

Aux#2) 2 Ports (2 FORM-C Relay Output (COM, NO, NC) /

DC12V-18V, Rating Max.2A) Output Port

2 Ports (TTL Output / DC5V,

Rating Max.20mA) LCD Graphic LCD (128 x 64

9

dots) 72.5mm x 39.5mm

(2.85 x 1.56) Screen

24-key Keypad

Back Lighting (12 Function Keys

included)

LCD , , (Selectable)

, , , (Optional)

, , , ,

, , (Programmable)

LED Indicator 3 Array LED Indicators (, ) Beeper Piezo Buzzer

Fingerprint Module

-15 +40C (+5 +104F)

LCD 0 +50C (+32 +122F)

Controller -15 +70C (+5 +158F)

RF Reader -35 + 65C (-31 +149F)

10% 90% relative

humidity (non-condensing)

/ , , , , , , & / Polycarbonate

( x x ) 192mm x 160mm x 45mm (7.56x6.29x1.77mm) 800 (1.76lbs) Certification FCC, CE, MIC

10

Fingerprint Module Specifications

Resolution 500dpi Capture Image Size 412 X 302 pixels Extraction Image Size 260 X 300 pixels Sensing Area 13mm X 15.2mm Scanner High Quality Optical Sensor FAR(False Acceptance

Ratio) 0.001%

FRR(False Reject Ratio) 0.1% ESD(Electro Static

Discharge) 15KV

Verification Time 1 . Identification Time 2 .

5. Identifying Supplied Parts

. , .

Main Unit Wall Mount Screws Cable & Diode &

Resistor UsersManual

1 1

3x8mm 1 3.5x12mm 4 3.5x40mm

4

Cable 6 Diode 2

Resistor 4 1

11

6. Product Overview 6.1 Features

Standalone IDTECK LX007 / LX007SR external reader ( 1 ). Biometrics access controller ID -. input signal, sensor activated exit button, Controller . . Access controller standalone device, , .

transactions . controller .

IDTECK LX007 / LX007SR , LCD module .

Input / Output

IDTECK LX007 / LX007SR 4 built-in input ports 4 output ports (2 relay outputs 2 TTL outputs) .

Time Schedule

10 time schedules 1 time schedule user . time schedule 8 time zones -(7 time zones) 1 . time zone 5 time codes 5 time codes . time schedules inputs outputs. , time schedule input device, input device time code. time schedule linked 1 holiday schedule.

12

Holiday Schedule

, 100 holidays 1 holiday schedule. holiday schedule linked 1 time schedule time code . holiday schedule time code holiday time zone time schedule.

Forced Door Open Alarm , door contact sensor . , door contact sensor door contact time outputs alarm devices. Forced Door Open Alarm alarm .

Door Open Timeout Alarm Door Open Timeout Alarm , . Overtime Door Open Alarm .

Anti-pass Back proximity reader , Anti-pass back mode . Anti-pass back mode, user user . , user .

Duress Alarm

: A. Holiday schedule 01 linked time schedule 01,

Holiday schedule 02 linked time schedule 02

B. Holiday schedule 02 linked time schedule 01,

Holiday schedule 01 linked time schedule 03

13

, Duress Password 2 . , duress alarm . duress alarm output TTL output alarm event .

ARM / DISARM Function Alarm Panel

ARM, reader ports inputs ports -. mode , IDTECK LX007 / LX007SR security devices .

Two Men Operation IDTECK LX007 / LX007SR user ( visitor) user special user ( guide). visitor guide -.

4 Level Individual Door Opening Time Setting 4 .

Name Display IDTECK LX007 / LX007SR user user -.

Function Key Name Display

function key software. , , punch-in punch-out function keys -. , punch-in punch-out software.

14

6.2 Product Explanation

6.2.1 Panel Description

Figure: Description of LX007 Front Panel

: LCD LX007. :

LX007, .

Relay #1 , .

Relay #2 , .

24 : LX007. Function Keys: LX007 12 function keys ([F1] - [F12]).

6.2.2 Connection Layout

24 ( 12 function)

CON-2

CON-1

CON-6

CON-3

CON-4CON-5

CON-7

15

Figure: Connector Layout

6.2.3 Color Coded & Wring Table

I/O PORT NAME SIGNAL NAME WIRE COLOR CON-1(2PIN CONNECTOR) Main Power (+12V) DC 12V Power Ground GND (-) CON-2 (3PIN CONNECTOR : Serial Printer) RS232-RX RXD RS232-TX TXD RS232-GND GND CON-3 (6PIN CONNECTOR) TTL OUTPUT #1 TTL#1, WD0 TTL OUTPUT #2 TTL#2, WD1 Aux Input #1 IN#1 Aux Input #2 IN#2 Wiegand DATA 0 DATA-0 Wiegand DATA 1 DATA-1 CON-4 (5PIN CONNECTOR) RS485-RTX(+) RS485-A(+) RS485-RTX(-) RS485-B(-) RS232-TX TXD RS232-RX RXD RS232-GND GND CON-5 (8PIN CONNECTOR) Door RELAY(NC) NC(1) Door RELAY(COM) COM(1) Door RELAY(NO) NO(1) Alarm RELAY(NC) NC(2) Alarm RELAY(COM) COM(2) Alarm RELAY(NO) NO(2) Exit Button EXIT Door Sensor CONTACT CON-6 (4PIN CONNECTOR : Door Phone (Optional)) DP_VCC

16

DP_GND DP_D0 DATA-0 DP_D1 DATA-1 CON-7: TCP/IP RJ45 CONNECTOR

7. Installation Tips & Check Point 7.1 Check Points

7.1.1 Selection of Cable ;

Figure: System Installation Layout

17

7.1.2 Recommended Cable Type and Permissible Length

+ : Thicker wires are needed if you connect a reader with high current consumption.

7.2 Check Point

7.2.1 Termination Resistor Termination resistors network transmission line. , receiver transmitted signal transmission line. termination resistors cable data rate communication

Reference Cable Specification

1 LX007 Power (DC12V)

DC Power -> LX007

Belden #9409, 18 AWG

2 conductor, unshielded

30m


4 conductor, shielded 2

Reader (Power and

Data) Exit Reader ->

RF20 Belden #9514,

22 AWG 8 conductor, shielded

150m


4 conductor, shielded 3

Door Contact Exit Button Sensor Input Input -> LX007


8 conductor, shielded

300m

4 Door Lock, Alarm Device

Lock (Alarm) -> LX007

Belden #9409, 18AWG

2 conductor, unshielded

300m

5 RS232 Cable Converter -> Host P.C.


2-twisted pair, shielded

15m

6 RS485 Cable

LX007 -> LX007 LX007 -> Converter


2-twisted pair, shielded

1,200m

18

system. , 9,600 baud rate cable 1,200 , 0.66 x ( cable), cable, transmitted signal 18.6us . data bit 52us . 18.6us termination resistors. , , cable network overlapped . , termination resistors receiver lines. 120 resistor termination resistor receiver lines A B 2 wires RS485. termination resistor 90 terminations 2 network system.

7.2.2 Termination Resistors

Figure: Termination resistors for 2 wire RS485

communication system

7.2.3 Grounding System for Communication Cable . shield wire communication cable ; communication cable . grounding points 3 ;

1. Earth Ground 2. Chassis Ground 3. Power Ground

shield wires ; , current flow shield wire voltage level shield wire current flow noise . , shield wire communication cable ; , shield wire ; , chassis ground shield wire

19

chassis ground; chassis ground, shield wire power ground. (GND LX007) chassis ground , . , power ground chassis ground.

Figure: Grounding system

7.2.4 Reverse Diode Connection inductor (Door Locks Alarm device) output relays, high surge voltage inductor. reverse diode, surge voltage electronic circuit controller. reverse diode inductor coils surge voltage.

Figure: Reverse Diode Connection

20

8. Installation of Product 8.1 Wall Mount (Unit: mm)

Figure: Wall Mount Layout

8.2 System Initialization , LX007 initialization . ( initialization LX007.) LCD Initialize OK? 1:Yes 0:No. initialize . initialization , normal mode IDTECK, LX007 [F1], Date Time.

21

KEY?

SYSTEM INITIALIZED!!!

Power ON

Initialize OK?1: Yes 0: No

Normal Operation

Yes

No

Press and hold the initialization button. Put the +12V DC power to the LX007. Release the button when the LCD displays Initialize OK?

8.3 1. 4 .

4 . 2. . 3. 4 , . 4. cable . 5. , .

8.4

8.4.1 Power 1. (+) wire DC 12V Power Supply . 2. GND (-) wire DC 12V Power Supply .

8.4.2 Input

Exit Button Connection 1. Exit Button . 2. Exit Button GND.

Door Contact Sensor Connection

22

1. Door Contact Sensor . 2. Door Contact Sensor GND.

Auxiliary Input Connection ( Aux Input #1(), Aux Input #2()) 1. Auxiliary Input Device Aux

Input #1 Aux Input #2. 2. Auxiliary Input Device GND.

Figure: Input Device Connection

2.2K Resistor Connection Cut Off Check 2.2K resistor input wire (e.g. ) GND Cut Off Check. , check the cutoff status device [F5 SETUP MENU] -> Cut Off Check. , output cutoff [F5 SETUP MENU] -> Cut Off Alarm.

23

Figure: 2.2K Resistor Connection for Cut Off

Check

8.4.3 Output Door Lock (Power Fail Safe) Connection (Door Relay)

1. COM wire Door Relay () +12V. 2. NC wire Door Relay () (+) wire

Door Lock. 3. GND wire (-) wire Door Lock.

Door Lock (Power Fail Secure) Connection (Door Relay)

1. COM wire Door Relay () +12V. 2. NO wire Door Relay () (+) wire

Door Lock 3. GND wire (-) wire Door Lock.

Alarm Device Connection (Alarm Relay)

1. COM wire Alarm Relay () +12V. 2. NO wire Alarm Relay () (+) wire

Alarm device. 3. GND port (-) wire Alarm device.

Figure: Door Lock, Alarm Device Connection

: REVERSE DIODES . DIODE

24

Fast Recovery DIODE (current=min. 1A), 1N4004 - 1N4007 .

8.4.4 External Reader

Proximity Reader

1. (+) wire Proximity Reader DC +12V. 2. (-) wire Proximity Reader GND. 3. Data-0 wire Proximity Reader . 4. Data-1 wire Proximity Reader .

Compatible Readers (External Reader):

LX007: Standard 26bit Wiegand Format Proximity Readers Standard 26bit Wiegand + 8bit Burst Format Proximity keypad Reader

LX007SR: Standard 34bit Wiegand Format Proximity Reader Standard 34bit Wiegand + 8bit Burst Format Proximity keypad Reader

Readers LX007: RF TINY, RF10/20/30/70/500, RFK101, FGR006, FGR006EX

LX007SR: SR10/20/30, SRK101, FGR006SRB

Figure: External Reader Connection

25

9. Communication

9.1 RS232 Communication Port Connection

9-pin connector (Serial communication connector, female) LX007 RS232 communication. . 1. RS232-TX () pin #2 (RXD) 9-pin

connector. 2. RS232-RX () pin #3 (TX) 9-pin

connector. 3. GND (Black wire) pin #5 9-pin connector. 4. 9-pin female connector COM Port host PC. 5. Install run the LX007 Application Software.

Figure: RS232 Communication

9.2 RS485 Communication Port Connection 9.2.1 RS485 Connection (Standalone Unit)

RS485/RS232 converter RS485 communication LX007 host PC. .

26

1. RS485-RTX (+) () RS485-A port converter.

2. RS485-RTX (-) () RS485-B port converter.

3. 9-pin connector (RS232) converter COM Port host PC.

4. Install run the LX007 Application Software.

Figure: RS485 Connection between the LX007 and a Host PC

9.2.2 RS485 Connection (Multiple Units)

RS485/RS232 converter RS485 communication LX007 host PC. .

, RS485 ports LX007 units parallel. ( 32 LX007 Units) 1. RS485-RTX (+) () LX007

RS485-RTX (+) (Yellow wire) LX007 . 2. RS485-RTX (-) () LX007 RS485-

RTX (-) () LX007 . 3. Address LX007 .

, RS485 ports LX007 units RS485/RS232 converter.

27

1. RS485-RTX (+) () LX007 RS485-A port Converter.

2. RS485-RTX (-) () LX007 RS485-B port Converter.

3. 9-pin connector (RS232) Converter COM port host PC.

4. Install run the LX007 application software.

Figure: RS485 Communication between Multiple LX007 Units and a PC

9.3 TCP/IP Communication Port Connection (Optional)

TCP/IP Module TCP/IP communication host PC. .

1. LAN cable network system RJ45 jack LX007. 2. LX007 TCP/IP port,

LX007 TCP/IP network LX007 RS485 multiple communication .

3. Address LX007 .

28

4. Install run the LX007 Application Software.

Figure: TCP/IP Communication between Multiple LX007 units and a host PC

9.4 Serial Printer 9-pin connector (Serial communication connector, female) LX007 serial printer RS232 communication. . 1. RS232-TX () pin #2 (RXD) 9-pin

connector. 2. RS232-RX () pin #3 (TX) 9-pin

connector. 3. GND, pin #5 9-pin connector. 4. 9-pin female connector COM Port serial

printer. 5. Print Output Auto Print Manual Print

[F3 SETUP MENU].

29

KEY?

SYSTEM INITIALIZED!!!

Power ON

Initialize OK?1: Yes 0: No

Normal Operation

Yes

No

Press and hold the initialization button. Put the +12V DC power to the LX007. Release the button when the LCD displays Initialize OK?

Figure: RS232 Communication between LX007 and a Serial Printer

10. Basic Setting 10.1 Initialization of LX007

, LX007 initialization . ( initialization LX007.) LCD Initialize OK? 1:Yes 0:No. initialize . initialization , normal mode IDTECK, LX007 [F1], Date Time.

30

10.2 SETUP MENU

LX007, SETUP MENU . , 8( 10) . (Default Master ID 00000000. LX007SR, 0000000000.) 10 SETUP MENUS [F1 SETUP MENU] . SETUP MENUS . , [F2 SETUP MENU], . [F5 SETUP MENU], , . SUBMENUS SETUP MENU - SUBMENU . 60 , LX007 SETUP MENU . Master ID [F7 SETUP MENU].

10.3

[LANGUAGE] [F1 SETUP MENU] . .

31

10.4

[SET DATE/TIME] [F1 SETUP MENU] 15 digits (i.e. / / / . / / / ) . LCD , . LX007 24-hour. Day 1 , 2 , 3 , 4 , 5 , 6 and 7 .

10.5 ID Registration

LX007, [F7 SETUP MENU] -> [REGISTRATION]. a) b) PIN.

32

a) b) PIN

NOTE| , F1 .

1. Scanning reader ID number.

beep . 2. ID Personal Identification Number (PIN)

4-8 . ID number (PIN) 4-8 . (ID number LX007SR 4-10 .)

33

3. PW password ID + Password.

4. TA Time Schedule code (00 - 10)

Reader#1 (i.e. built-in reader). Time Schedule, -. Time Schedule code, Time Schedule Setup [F4 SETUP MENU]. -, Time Schedule code '00'.

5. TB Time Schedule code (00 - 10)

Reader#2 (i.e. the exit reader). Time Schedule, -. Time Schedule code, Time Schedule Setup [F4 SETUP MENU]. -, Time Schedule code '00'.

6. RD Reader Assignment code . 0 readers (Built-in Reader Exit Reader), 1 Reader#1 (Built-in Reader) 2 Reader#2 (Exit Reader). 1 RD field( Reader#1) Reader#2 (Exit Reader) LX007 (Access Door Error) LCD.

7. C ID code. 0 default 1 2 TWO MEN MODE. 3 ARM/DISARM function 4 .

8. MA Operating Mode Reader#1 (i.e.

the built-in reader). 1 MA, , - ID .

0 Operating Mode ([F1 SETUP MENU] > [READER#1 MODE])

1 ID Only Mode 2 ID + Fingerprint (Password)

34

3 ID + Password + Fingerprint 9. MB Operating Mode Reader#2 (Exit

Reader). 0 Operating ([F1 SETUP MENU] >

[READER#2 MODE]) 1 ID Only Mode 2 ID + Password Mode NOTE: ID + Password Mode Reader#2 .

10. LV Output Operating Level . Output

operating time user. output operating time level, Output Setting [F6 SETUP MENU].

0 1 Level #1 2 Level #2 3 Level #3 4 Level #4

11. FP Fingerprint Usage Flag (1 digit).

user fingerprint. 0 fingerprint 1 fingerprint

c) Scanner , scanner .

35

Figure: How to put your finger on the scanner

11. 11.1

LX007, .

( PIN) , (Relay#1) 3 (Default) .

, (Relay#1) 3 .

, (Relay#2) 3 .

11.2 initialized, (i.e. the default settings) restored .

36

12. Setting Changes

LX007, SETUP MENU . , 8( 10) . (Default Master ID 00000000. LX007SR, 0000000000.) 10 SETUP MENUS [F1 SETUP MENU] . SETUP MENUS . , [F2 SETUP MENU], . [F5 SETUP MENU], , . SUBMENUS SETUP MENU - SUBMENU . 60 , LX007 SETUP MENU . Master ID [F7 SETUP MENU].

INITIAL DISPLAY(MODEL NAME, CURRENT TIME)

ID INPUT?

MASTER ID /PW/FINGERPRINT ?

YES

YES

NO

NORMAL OPERATIONS MODE

SETUP MODE

NO

F1 SETUP MENU

F2 SETUP MENU

F3 SETUP MENU

F4 SETUP MENU

F5 SETUP MENU

F6 SETUP MENU

F7 SETUP MENU

F8 SETUP MENU

F9 SETUP MENU

F10 SETUP MENU

37

12.1 F1 SETUP MENU

LANGUAGE

SET DATE/TIME

READER#1 MODE

ENGLISH (DEFAULT)

or KEY

or KEY

or KEY

or KEY

READER#2 MODE

RD1 PIN INPUT

RD2 PIN INPUT

or KEY

or KEY

or KEY

COMM ADDR SET

or KEY

BAUD RATE

KOREAN

CHINESE

JAPANESE

ESPANOL

PORTUGUESE

Enter 15 digits for date and time

ID ONLY

ID+F/P (P/W) (DEFAULT)

ID+P/W+F/P

ID ONLY(DEFAULT)

ID+P/W

NOT USE(DEFAULT)

USE

NOT USE(DEFAULT)

USE

9600

19200(RECOMMENDED)

38400

57600

ARABIC

Enter 3 digits in the 000-255 range

Basic Languages

Optional Languages

38

12.1.1

12.1.2

12.1.3 Reader #1 Mode

default . , .

e.g. 200802101330152 = Feb. 10, 2008, 13:30:15, Monday

NOTE: READER#1 built-in proximity reader . ID(PIN) ONLY: users - ID number

. ID+F/P(P/W): users - ID number

. users , password .

ID+P/W+F/P: users - ID number password.

39

12.1.4 Reader #2 Mode

READER#2 MODE READER#1 MODE.

12.1.5 Reader #1 PIN Input

12.1.6 Reader #2 PIN Input

READER#2 PIN INPUT READER#1 PIN INPUT.

12.1.7 Communication Address Setting

000. .

Reader#1..- user ID, USE.

NOTE: READER#2 Exit Reader LX007. ID ONLY: mode password ID+P/W: mode password

40

12.1.8 Baud Rate Setting

LX007 Baud Rates 9600, 19200, 38400 57600bps. Baud Rate 19200bps. Baud Rate. Baud Rate network . , ; - LX007 host PC Software. - Baud Rate LX007 host PC Software. - COM port cable. - COM port settings host PC (Parity Bit: None, Data Bit: 8 bits, Stop Bit: 1 bit)

41

12.2 F2 SETUP MENU

APB MODE

DURESS MODE

WIEGAND OUTPUT

or KEY

or KEY

or KEY

or KEY

OPEN ALR TIME

EVENT MEMORY

ID DISPLAY

TIME UNIT

or KEY

or KEY

or KEY

OUTPUT T/S+ID

or KEY

USE(DEFAULT)

NOT USE

MESSAGE(DEFAULT)

ID+MESSAGE

UNIT: 1 SEC (DEFAULT)

UNIT: 0.1 SEC

NOT USE(DEFAULT)

USE

NOT USE(DEFAULT)

USE

NOT USE(DEFAULT)

USE

NOT USE(DEFAULT)

USE

ALL FLAG RESET

DURESS P/W SETTING

Enter 2 digits for Open Alarm Time

42

12.2.1 Event Memory

12.2.2 ID Display

12.2.3 Time Unit Setting

event memory . USE, LX007 event transactions . NOT USE, event transactions . , NOT USE.

ID numbers , ID+MESSAGE. MESSAGE: asterisks ******** ID

number . ID+MESSAGE: ID number MESSAGE.

43

12.2.4 Output T/S + ID

. 1sec: Output Time 1 -. 0.1sec: Output Time 1/10 ( 100ms)-. e.g. Door Relay (Relay #1, DR) 3 ,

; - Time Unit 1 . - Door Relay (DR) 03.

e.g. Door Relay (Relay #1, DR) 0.5, ;

- Time Unit 0.1 . - Door Relay (DR) Output 05.

Output Time Schedule [F5 SETUP MENU].Output Time Schedule . Output T/S + ID USE, . .

NOT USE: . USE: . NOT USE

44

12.2.5 Anti-pass Back Mode

12.2.6 Duress Mode

Duress Mode Reader#1. NOT USE. USE, Duress 00. , 2 . .

NOTE | , Duress Password . Duress Alarm host PC .

CAUTION | Duress Password ARM and DISARM codes .

Anti-pass back user 2 . Exit Reader. mode Exit Button Exit Reader.

NOT USE: Anti-pass back. USE: Anti-pass back. ALL FLAG RESET: Anti-pass back flags reset,

- flags.

45

12.2.7 Wiegand Output

12.2.8 Door Open Alarm Time Setting

Door Open Alarm Time delay Door Relay Time Door Open Alarm . 00: Door Relay time . 01-98: Delay (01-98 .) . 99: .

NOTE | .

LX007 reader ( controller). USE, LX007 26bit Wiegand Output TTLoutput 2 ports. (LX007SR 34bit Wiegand output.)

NOT USE: TTL outputs . USE: 26bit Wiegand outputs TTL1 TTL2

ports. , ID SCANNING OK. (TTL1 : Data 0 TTL2 : Data 1)

46

12.3 F3 SETUP MENU

12.3.1 Print Output

ONE TIME READ

or KEY

PRINT OUTPUT

VOICE VOLUME

ARM/DISARM

or KEY

or KEY

or KEY

TWO MEN MODE

or KEY

NOT USE(DEFAULT)

MANUAL PRINT

0(MUTE) - 4(MAXIMUM)

NOT USE(DEFAULT)

USE

MAX. USER SETUP

or KEY

10,000(DEFAULT)

20,000

AUTO PRINT

NOT USE(DEFAULT)

USE

NAME DISPLAY

or KEY

NOT USE(DEFAULT)

USE

Enter a 2-digit ARM/DISARM code

47

12.3.2 Voice Volume

12.3.3 Arm/Disarm

serial printer, LX007 ID, data, time, function key, .

AUTO PRINT: new event. MANUAL PRINT: 0 () 1 (). NOT USE: .

0 () 4 ().

Arm Code Disarm Code. , LX007 ARM mode ARM code ARM/DISARM(i.e. Code 3). LX007 ARM mode,readers . LX007, Disarm Code ARM/DISARM card.

CAUTION | ARM Code, DISARM Code, Duress Code .

48

12.3.4 Two Men Mode

12.3.5 One Time Read

12.3.6 Max. User Setup

, guides GuideGroup(C:1) visitor cards Visitor Group(C:2). two-man mode , LX007 guidecard visitor card .

USE, 30 .

; 10,000 20,000. 20,000, transactions 10,000. CAUTION: , initialize

.

49

12.3.7

User . NOTE: User downloaded software .

user , user .

CAUTION: USE, maximum number IDs 10,000.

50

12.4 F4 SETUP MENU

12.4.1 Time Schedule

10 Time Schedule Codes. Time Schedule Code 00 default users . user Time Schedule Codes 01 10. Time Schedule Code 8 (i.e. Sun, Mon, Tue, Wed, Thu, Fri, Sat Holiday) 5 (i.e. Shift Time Accessible Time Zone.)

i h d l / d i

TIME SCHEDULE

HOLIDAY

HOLIDAY CODE

or KEY

or KEY

or KEY

or KEY

RD1 MODE

51

12.4.2 Holiday

10 Holiday Schedule Codes. Holiday Schedule Code 00 default, . user Holiday Schedule Codes 01 10. Holiday Schedule Code 100 .

Holiday Code H/S Code, Holiday number Date. Holiday Schedule Code 01 10 Holiday 001

52

12.4.3 Holiday Code

12.4.4 Reader#1 Mode Time Schedule

Holiday Code Holiday Schedule Time Schedule. Time Schedule 5 Holiday Schedule. HolidaySchedule Code 00 Time Schedule.

T/S Code 01 10 . Holiday Schedule Code 2-digit . .

3 ID Only Mode, ID+F/P(PW) Mode ID+PW+F/P Mode. [R1 MODE SETTING] [F1 SETUP MENU]. ID Only Mode ., - 09:00 17:00. [R1 MODESETTING] ID+F/P Mode, T/S Code 01 09:00 17:00. link TimeS h d l C d 01 R1 MODE Ti S h d l li k

53

12.4.5 Reader#2 Mode Time Schedule

READER#2 MODE TIME SCHEDULE READER#1 MODE T/S, .

12.4.6 Voice Time Schedule

Voice T/S time schedules .

time schedule code . timeschedule, .

, .

54

12.5 F5 SETUP MENU

TAMPER ALARM

or KEY

EXIT BUTTON

DOOR CONTACT

AUX INPUT #1

AUX INPUT #2

DOOR TIME OUT

CUT OFF ALARM

DURESS ALARM

CUT OFF CHECK

ARM/DISARM OUT

OUTPUT T/S

INPUT T/S

INPUT TYPE

Output operation time: 10 DIGITS









Time schedule code: 10 DIGITS

Time schedule code: 10 DIGITS

Cut off check flag: 10 DIGITS

NO/NC flag: 10 DIGITS

55

Input Sources

12.5.1 Exit Button Output Setting

OUTPUT Door Relay (DR)

Alarm Relay (AR)

TTL#1 (T1)

TTL#2 (T2)

Buzzer (BZ)

[1] EXIT BUTTON 03 00 00 00 00 [2] DOOR CONTACT 00 99 00 00 00 [3] AUX Input #1 00 00 00 00 00 [4] AUX Input #2 00 00 00 00 00 [5] TAMPER ALARM 00 99 99 99 99 [6] CUT OFF ALARM 00 00 00 00 00 [7] DURESS ALARM 00 00 00 00 00 [8] ARM/DISARM OUT 00 00 00 00 00 [9] DOOR TIME OUT 00 99 00 00 00 [10] OUTPUT TIME SCHEDULE 00 00 00 00 00

INPUT Exit Button (EX)

Door Contact Sensor (DC)

Aux Input #1 (I1)

Aux Input #2 (I2)

Tamper Switch (TP)

[11] INPUT TIME SCHEDULE 00 00 00 00 00 [12] CUT OFF CHECK 00 00 00 00 00 [13] INPUT TYPE 00 00 00 00 00

9 , EXIT. 9 03 , 1 sec, 3

. 0.1 sec, 0.3 9 00 98 ( 0.0 9.8

0.1 .) 99, reset.

z DR: Door Relay Output z AR: Alarm Relay Output z T1: TTL#1 Output z T2: TTL#2 Output z BZ: Buzzer Output

56

12.5.2 Door Contact Output Setting 12.5.3 Aux Input#1 Output Setting 12.5.4 Aux Input#2 Output Setting 12.5.5 Tamper Alarm Output Setting 12.5.6 Cut Off Alarm Output Setting 12.5.7 Duress Alarm Output Setting 12.5.8 Arm/Disarm Output Setting 12.5.9 Door Time Output Setting

Exit Button Output 12.5.1.

12.5.10 Output Time Schedule Setting

12.5.11 Input Time Schedule Setting

9 Time Schedule Code output. Time Schedule Code output 00, Time Schedule.

9 . Time Schedule Code 2-digit output.

z DR: Door Relay Output T/S Code z AR: Alarm Relay Output T/S Code z T1: TTL#1 Output T/S Code z T2: TTL#2 Output T/S Code z BZ: Buzzer Output T/S Code

57

12.5.12 Cut Off Check Setting

12.5.13 Input Type Setting

9 Time Schedule Code input. Time Schedule Code input 00, Time Schedule. activate PIR sensor input .

9 , Time Schedule Code 2-digit input.

z EX: EXIT Button Input T/S Code z DC: Door Contact Sensor Input T/S Code z I1: Aux Input#1 T/S Code z I2: Aux Input#2 T/S Code z TP: Tamper Switch Input T/S Code

cutoff input port. 00 01 . CAUTION: , 2.2K resistor input

wire GND.

input NO(Normally Open) NC(NormallyClose). 00 NO 01 NC. 00(NO).

58

12.6 F6 SETUP MENU

RD1 ID ERROR

or KEY

RD1 ID OK LV1

RD1 ID OK LV2

RD1 ID OK LV3

RD1 ID OK LV4

RD2 ID OK LV2

RD1 T/S ERROR

RD1 APB ERROR

RD2 ID ERROR

RD2 ID OK LV1

RD2 ID OK LV3

RD2 ID OK LV4

RD2 T/S ERROR

RD2 APB ERROR















59

Inputs

12.6.1 Output Setting for Reader#1 ID OK Level 1


Alarm Relay (AR)

TTL#1 (T1)

TTL#2 (T2)

Buzzer (BZ)

[1] Reader#1 ID OK LV1 03 00 00 00 00 [2] Reader#1 ID OK LV2 05 00 00 00 00 [3] Reader#1 ID OK LV3 05 00 00 00 00 [4] Reader#1 ID OK LV4 05 00 00 00 00 [5] Reader#1 ID Error 00 03 00 00 00 [6] Reader#1 T/S Error 00 03 00 00 00 [7] Reader#1 APB Error 00 03 00 00 00 [8] Reader#2 ID OK LV1 03 00 00 00 00 [9] Reader#2 ID OK LV2 05 00 00 00 00 [10] Reader#2 ID OK LV3 05 00 00 00 00 [11] Reader#2 ID OK LV4 05 00 00 00 00 [12] Reader#2 ID Error 00 03 00 00 00 [13] Reader#2 T/S Error 00 03 00 00 00 [14] Reader#2 APB Error 00 03 00 00 00

60

Output Time 12.6.2 12.6.14 12.6.1 RD1 ID OK Level 1 Output setting.

12.6.2 Output Setting for Reader#1 ID OK Level 2 output time users Level#2 output.



12.6.5 Output Setting for Reader#1 ID Error output time user Reader #1 -.

12.6.6 Output Setting for Reader#1 T/S Error

output time user - time schedule.

9 Output Activation Time, output EXIT. Output Activation Time V seconds, 1 , V/10seconds, provided that the Time Unit is set to 0.1. (V = Activation Time output.)

9 00 98 ( 0.0 9.8 0.1 .) 99, output activated reset Output.

z DR: Door Relay Output z AR: Alarm Relay Output z T1: TTL#1 Output z T2: TTL#2 Output z BZ: Buzzer Output

61

12.6.7 Output Setting for Reader#1 APB Error

Output Time user - one-entry-one-exit Anti-pass-back.

12.6.8 Output Setting for Reader#2 ID OK Level 1 Output Time users Level#1 output.




12.6.12 Output Setting for Reader#2 ID Error output time user Reader #2 -.

12.6.13 Output Setting for Reader#2 T/S Error output time user - time schedule.

12.6.14 Output Setting for Reader#2 APB Error Output Time user - one-entry-one-exit Anti-pass-back.

62

12.7 F7 SETUP MENU

12.7.1 ID Registration

a) Registration by Card b) Registration Using Keypad

ID COUNT

EVENT COUNT

or KEY

or KEY

ID REGISTRATION

ID DELETION

ID LIST

or KEY

or KEY

or KEY

MASTER ID REG.

or KEY

CARD

KEY

REGISTERED IDs are displayed

THE NUMBER OF REGISTERED IDs is displayed

THE NUMBER OF STORED EVENTS is displayed

Select the Master Card number to register.

Present the card or enter the ID number.

63

NOTE| , F1 .

1. Scanning reader ID number.

beep . 2. ID Personal Identification Number (PIN)

4-8 . ID number (PIN) 4-8 . (ID number LX007SR 4-10 .)

3. PW password ID +

Password. 4. TA Time Schedule code (00 - 10)

Reader#1 (i.e. built-in reader). Time Schedule, -. Time Schedule code, Time Schedule Setup [F4 SETUP MENU]. -, Time Schedule code '00'.

5. TB Time Schedule code (00 - 10)

Reader#2 (i.e. the exit reader). Time Schedule, -.

64

Time Schedule code, Time Schedule Setup [F4 SETUP MENU]. -, Time Schedule code '00'.

6. RD Reader Assignment code . 0 readers (Built-in Reader Exit Reader), 1 Reader#1 (Built-in Reader) 2 Reader#2 (Exit Reader). 1 RD field( Reader#1) Reader#2 (Exit Reader) LX007 (Access Door Error) LCD.

7. C ID code. 0 default 1 2 TWO MEN MODE. 3 ARM/DISARM function 4 .

8. MA Operating Mode Reader#1 (i.e.

the built-in reader). 1 MA, , - ID .

0 Operating Mode ([F1 SETUP MENU] > [READER#1 MODE])

1 ID Only Mode 2 ID + Fingerprint (Password) 3 ID + Password + Fingerprint

9. MB Operating Mode Reader#2 (Exit

Reader). 0 Operating ([F1 SETUP MENU] >

[READER#2 MODE]) 1 ID Only Mode 2 ID + Password Mode NOTE: ID + Password Mode Reader#2 .

10. LV Output Operating Level . Output

operating time user. output operating time level, Output

65

Setting [F6 SETUP MENU]. 0 1 Level #1 2 Level #2 3 Level #3 4 Level #4

11. FP Fingerprint Usage Flag (1 digit).

user fingerprint. 0 fingerprint 1 fingerprint

12.7.2 ID Deletion

12.7.3 ID List

Ids LX007 IDnumber. ID DELETION, . , I D number 8 . ID number LCD ID IDDELETED LCD. ID number , UNREGISTERED ID . IDs .

66

12.7.4 Master ID Registration

MASTER ID

MASTER ID PIN

ID Index 5 , ID number 8 , Password 4 ,Timeschedule Reader#1(TA) Reader#2(TB), IDcode(C), accessible Readers(RD), operating mode Reader#1(MA) Reader#2(MB), output level(LV) usage of Fingerprint(FP) User. EMPTY . FIRST ID . LAST ID .

67

12.7.5 ID Count

12.7.6 Event Count

user Ids . IDs IDs . user Ids 123 .

1,000 (standard). 2,000/4,000 user IDs

Master ID 00000000 ( 0000000000 LX007SR) . 10 Master IDs ( 01 10) LX007. NOTE: Master ID, 00000000 ( 0000000000

LX007SR) Master ID Registration.

events . event . Events 12345 .

event buffers 20,000. events uploaded host PC, .

68

12.8 F8 SETUP MENU

12.8.1 System Initialize

initialize LX007. initialization ( LX007 reset ).

CAUTION: Initialize . initialize . WAIT.. initialized. initialization , LX007 Setup menu.

T/S CLEAR

DEFAULT SET

or KEY

or KEY

SYSTEM INITIAL

EVENT CLEAR

ID CLEAR

or KEY

or KEY

or KEY

MASTER ID CLR

or KEY

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

YES

NO

69

event memory , event memory . , event memory .

CAUTION: , . , upload host PC, .

12.8.2 Event Clear

12.8.3 ID Clear

12.8.4 Master ID Clear

User Ids , menu . , User Ids .

C A U T I O N : , . .

Master Ids , , Master IDs . C A U T I O N : , .

.

70

12.8.5 Time Schedule Clear

12.8.6 Default Setting

Time Schedules (01~10), Holidayschedules(01~10), Holiday code, Reader#1 Mode TimeSchedule code Reader#2 Mode Time Schedule code, T/S . C A U T I O N : , .

.

restore LX007, restore . CAUTION: restore Reader Mode, COMM

Address etc, ; .

71

Firmware Version LCD. [F9 SETUPMENU].

12.9 F9 SETUP MENU

12.9.1 Version Check

KEYPAD TEST

READER TEST

or KEY

or KEY

FIRMWARE VER.

INPUT TEST

OUTPUT TEST

or KEY

or KEY

or KEY

LCD TEST

or KEY

THE CURRENT VERSION OF FIRMWARE IS DISPLAYED

VERIFY THAT THE INPUT PORTS PROPERLY WORK.

MEMORY TEST

or KEY

VERIFY THAT THE OUTPUT PORTS PROPERLY WORK.

VERIFY THAT THE LCD SCREEN PROPERLY WORKS.

VERIFY THAT ALL THE KEYS ON THE KEYPAD WORK.

VERIFY THAT THE READER PROPERLY WORKS.

VERIFY THAT COMMUNICATION PROPERLY WORKS.

COMM TEST

or KEY

VERIFY THAT THE MEMORY PROPERLY WORKS.

72

12.9.2 Input Test

12.9.3 Output Test

12.9.4 LCD Test

12.9.5 Keypad Test

5 input status, 0 input port opencircuit, 1 input port short circuit ground level, 2 input port.

output relays (Door Relay Alarm Relay). relays . TTL#1 TTL#2 outputs. InternalBuzzer. 2 .

. , LAST UPDATEPRESS ANY KEY.

73

12.9.6 Reader Test

12.9.7 Memory Test

12.9.8 Communication Test

. . ENT # ESC *.

Scanning, LX007 . . , 8 ( 10 LX007SR).

, TEST FAILED. , .

74

9 . ,

RS232 TX () RS232 RX wire () .

9 , TEST FAILED. , .

9 , TEST PASSED. 9 , .

75

12.10 F10 SETUP MENU

12.10.1 Dual Fingerprint Mode

DUAL FINGER

? Number of Templates and Fingers

Authentication Success

Ratio Recommended Authenticatio

n Mode NOT USE

2 storage templates for a single finger. High

Identification Mode

USE 1 storage template each for 2 different fingers. Low

Verification Mode

Dual finger mode USE , 2 1 ID , .

FP REG. COUNT

MODULE VERSION

or KEY

or KEY

DUAL F/P MODE

ADAPTIVE MODE

IDENTIFICATION

or KEY

or KEY

or KEY

USE

NOT USE(DEFAULT)

USE

NOT USE(DEFAULT)

USE(DEFAULT)

NOT USE

The version of the installed fingerprint module is displayed

The current number of the registered

fingerprints in the device is displayed

76

12.10.2 Adaptive Mode

12.10.3 Identification Mode

12.10.4 FP Reg. Count

12.10.5 Module Version

ADAPTIVE MODE, LX007 , . .

IDENTIFICATION MODE, users LX007. Users -. IDENTIFICATION MODE VERIFICATION MODE

.

77

version fingerprint module.

78

APPENDIX

A. INPUT OUTPUT () Default Output Settings for Input Sources

* Index No. [1] - [9]

operating time output input signal. 99 forever.

* Index No. [10] time schedule code (index) output.

* Index No. [11] time schedule code (index) input.

* Index No. [12] cut off check input . (0 NOT USE, 1 USE)

* Index No. [13]


Alarm Relay (AR)

TTL#1 (T1)

TTL#2 (T2)

Buzzer (BZ)

[1] EXIT BUTTON 03 00 00 00 00 [2] DOOR CONTACT 00 99 00 00 00 [3] AUX Input #1 00 00 00 00 00 [4] AUX Input #2 00 00 00 00 00 [5] TAMPER ALARM 00 99 99 99 99 [6] CUT OFF ALARM 00 00 00 00 00 [7] DURESS ALARM 00 00 00 00 00 [8] ARM/DISARM OUT 00 00 00 00 00 [9] DOOR TIME OUT 00 99 00 00 00 [10] OUTPUT TIME SCHEDULE 00 00 00 00 00

INPUT Exit Button (EX)

Door Contact Sensor (DC)

Aux Input #1 (I1)

Aux Input #2 (I2)

Tamper Switch (TP)

[11] INPUT TIME SCHEDULE 00 00 00 00 00 [12] CUT OFF CHECK 00 00 00 00 00 [13] INPUT TYPE 00 00 00 00 00

79

input type NO(Normally Open) NC(Normally Closed). (0 NO, 1 NC)

80

Output Input

* Index No. [1] - [14]: operating time output

input signal.

OUTPUT INPUT

Door Relay (DR)

Alarm Relay (AR)

TTL#1 (T1)

TTL#2 (T2)

Buzzer (BZ)

[1] Reader#1 ID OK LV1 03 00 00 00 00 [2] Reader#1 ID OK LV2 05 00 00 00 00 [3] Reader#1 ID OK LV3 05 00 00 00 00 [4] Reader#1 ID OK LV4 05 00 00 00 00 [5] Reader#1 ID Error 00 03 00 00 00 [6] Reader#1 T/S Error 00 03 00 00 00 [7] Reader#1 APB Error 00 03 00 00 00 [8] Reader#2 ID OK LV1 03 00 00 00 00 [9] Reader#2 ID OK LV2 05 00 00 00 00 [10] Reader#2 ID OK LV3 05 00 00 00 00 [11] Reader#2 ID OK LV4 05 00 00 00 00 [12] Reader#2 ID Error 00 03 00 00 00 [13] Reader#2 T/S Error 00 03 00 00 00 [14] Reader#2 APB Error 00 03 00 00 00

81

B. TROUBLE SHOOTING

batch-downloading IDs PC. download .

1. controller. batch-downloading IDs PC, LX007 ID memory. .

2. PC . 3. , download . 4. .

Master ID 00000000 Setup Mode.

Master ID .

1. Master ID software. (Master ID 00000000.)

2. , initialize : , LX007 initialization button . Initialize OK? 1:Yes 0:No. initialize . initialization , normal mode IDTECK, LX007 [F1], Date Time.

3. . - - PIN .

.

1. . , . : - Master ID (=00000000) Setup mode. - . - [LANGUAGE] LCD, [RD1_PIN_INPUT] [ENT] USE .

2. .

82

Setup Mode normal operating mode.

LX007 normal operating mode

60 . ; beep~ beep ~ beep beeeeeeeep~~~~. , Internal circuits.

1. . 3 (). 2. door contact sensor type: NO/NC-type.

3. 10 Time schedule code (01-10) output T/S, [7. OUTPUT T/S] F6 Setup Menu. time schedule code 01 10 . time schedule , time schedule code 00

4. Tamper switch LX007. 5. .

SCHEDULE ERROR . , time schedule .

1. LX007 , . initialize .

2. . - time zone - user, time schedule time schedule code(1-10) user . - user -, 00.

3. software time schedule LX007 PC.

4. . ACCESS DOOR ERR . user .

83

1. the LX007 , . initialize . 2. : - controller 2 reader ports, RD user -. - RD 1, Reader 1. Reader 2, ACCESS DOOR ERR . - RD 2, Reader 2. Reader 1, ACCESS DOOR ERR . - RD 0 3, reader 1 2 .

3. .

LX007 Host PC.

, COMM ID controller, communication port ( PC controller).

1. software controller. - COMM ID controller software. - COMM ID controllers 1 . - communication speed (9600bps ) software. - PCs COM port S/W. - parameters software : Parity bit : NONE Data bit : 8 bits Stop bit : 1 bit

2. .

RS232 RS485 (mono) LX007 PC LX007 RS485/232 Converter PC RX TX RTX(-) RTX(-) TX RX RTX(+) RTX(+) GND GND

The RS232 cable from the converter

RS485(Multi Drop)

84

LX007 LX007 RS485/232Converter PC RTX(-) RTX(-) RTX(-) RTX(+) RTX(+) RTX(+)

The RS232 cable from the Converter

3. resistors 120 Ohm RTX (+) RTX (-) RS485. resistors Converter RS485 .

4. , one to one. 5. .

1. 2. General 3. Features 4. Specification 5. Identifying Supplied Parts 6. Product Overview 6.1 Features 6.2 Product Explanation 6.2.1 Panel Description 6.2.2 Connection Layout 6.2.3 Color Coded & Wring Table

7. Installation Tips & Check Point 7.1 Check Points 7.1.1 Selection of Cable 7.1.2 Recommended Cable Type and Permissible Length

7.2 Check Point 7.2.1 Termination Resistor 7.2.2 Termination Resistors 7.2.3 Grounding System for Communication Cable 7.2.4 Reverse Diode Connection

8. Installation of Product 8.1 Wall Mount (Unit: mm) 8.2 System Initialization 8.3 8.4 8.4.1 Power 8.4.2 Input 8.4.3 Output 8.4.4 External Reader

9. Communication 9.1 RS232 Communication Port Connection 9.2 RS485 Communication Port Connection 9.2.1 RS485 Connection (Standalone Unit) 9.2.2 RS485 Connection (Multiple Units)

9.3 TCP/IP Communication Port Connection (Optional) 9.4 Serial Printer

10. Basic Setting 10.1 Initialization of LX007 10.2 SETUP MENU 10.3 10.4 10.5 ID Registration

11. 11.1 11.2

12. Setting Changes 12.1 F1 SETUP MENU 12.1.1 12.1.2 12.1.3 Reader #1 Mode 12.1.4 Reader #2 Mode 12.1.5 Reader #1 PIN Input 12.1.6 Reader #2 PIN Input 12.1.7 Communication Address Setting 12.1.8 Baud Rate Setting

12.2 F2 SETUP MENU 12.2.1 Event Memory 12.2.2 ID Display 12.2.3 Time Unit Setting 12.2.4 Output T/S + ID 12.2.5 Anti-pass Back Mode 12.2.6 Duress Mode 12.2.7 Wiegand Output 12.2.8 Door Open Alarm Time Setting

12.3 F3 SETUP MENU 12.3.1 Print Output 12.3.2 Voice Volume 12.3.3 Arm/Disarm 12.3.4 Two Men Mode 12.3.5 One Time Read 12.3.6 Max. User Setup 12.3.7

12.4 F4 SETUP MENU 12.4.1 Time Schedule 12.4.2 Holiday 12.4.3 Holiday Code 12.4.4 Reader#1 Mode Time Schedule 12.4.5 Reader#2 Mode Time Schedule 12.4.6 Voice Time Schedule

12.5 F5 SETUP MENU 12.5.1 Exit Button Output Setting 12.5.2 Door Contact Output Setting 12.5.3 Aux Input#1 Output Setting 12.5.4 Aux Input#2 Output Setting 12.5.5 Tamper Alarm Output Setting 12.5.6 Cut Off Alarm Output Setting 12.5.7 Duress Alarm Output Setting 12.5.8 Arm/Disarm Output Setting 12.5.9 Door Time Output Setting 12.5.10 Output Time Schedule Setting 12.5.11 Input Time Schedule Setting 12.5.12 Cut Off Check Setting 12.5.13 Input Type Setting

12.6 F6 SETUP MENU 12.6.1 Output Setting for Reader#1 ID OK Level 1 12.6.2 Output Setting for Reader#1 ID OK Level 2 12.6.3 Output Setting for Reader#1 ID OK Level 3 12.6.4 Output Setting for Reader#1 ID OK Level 4 12.6.5 Output Setting for Reader#1 ID Error 12.6.6 Output Setting for Reader#1 T/S Error 12.6.7 Output Setting for Reader#1 APB Error 12.6.8 Output Setting for Reader#2 ID OK Level 1 12.6.9 Output Setting for Reader#2 ID OK Level 2 12.6.10 Output Setting for Reader#2 ID OK Level 3 12.6.11 Output Setting for Reader#2 ID OK Level 4 12.6.12 Output Setting for Reader#2 ID Error 12.6.13 Output Setting for Reader#2 T/S Error 12.6.14 Output Setting for Reader#2 APB Error

12.7 F7 SETUP MENU 12.7.1 ID Registration 12.7.2 ID Deletion 12.7.3 ID List 12.7.4 Master ID Registration 12.7.5 ID Count 12.7.6 Event Count

12.8 F8 SETUP MENU 12.8.1 System Initialize 12.8.2 Event Clear 12.8.3 ID Clear 12.8.4 Master ID Clear 12.8.5 Time Schedule Clear 12.8.6 Default Setting

12.9 F9 SETUP MENU 12.9.1 Version Check 12.9.2 Input Test 12.9.3 Output Test 12.9.4 LCD Test 12.9.5 Keypad Test 12.9.6 Reader Test 12.9.7 Memory Test 12.9.8 Communication Test

12.10 F10 SETUP MENU 12.10.1 Dual Fingerprint Mode 12.10.2 Adaptive Mode 12.10.3 Identification Mode 12.10.4 FP Reg. Count 12.10.5 Module Version

lx007 hardware(thai)

Documents

installation of product

connection layout

power connection

input connection

output connection

communication cable

wall mount installation

reverse diode connection