m100 led recessed [l1rx] · pdf fileseparate led mr16 downlight switching. ccea. 12. ccea...

of 15(Rev. 04/2018)

M100LED Recessed_v[1B]3.1 In a continuing eff ort to off er the best product possible, we reserve the right to change, without notice, specifi cations or materials that in our opinion will not alter the function of the product. Specifi cation sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.

Selux Corporation © 2017, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us

Project:

Type: Qty:

Date: Customer:

M100LED Recessed

Order Code: - - - - - - - - - - - -

LED Recessed

Order Code: - - - - - - - - - -

Series L10 Multi-Mount Form

L1R1Continuous Flange(Flanged Endcaps)

L1R2Continuous Flange(Flangeless Endcaps)

Custom colors are available, Please consult factory

Light Engine

CCT 303000K

353500K

404000K

Shielding LWLED Optimizedwhite lens

MountingL10

SGSlot Grid (9/16”) (Wire Suspension or 1/4-20 stud)

SF1Spackle Flange (1/2” Drywall)

SF2Spackle Flange (5/8” Drywall)

SF3Spackle Flange (After Drywall)

DCDecoustic Ceiling (up to 2” thick)

NominalFixtureLength

01*1 ft.

026

2 ft.046

4 ft.033 ft.

056

5 ft.066

6 ft.086

8 ft.077 ft.

XXRuns (over 8’) & Confi gurations, round up to the nearest foot and replace the “xx” with the # (i.e. 09=09’ nominal)

Finish WHWhite

BKBlack

SVSilver

SPSpecify Premium Color

Voltage 120120 Volt

277277 Volt

LED WARRANTY

5YEAR

ARRA Compliant

272700K

EmergencyOptions

EC17

Emergency Circuit Wiring

V9020

Lit Inverted90° Corner

IT9020

Lit “T” section IX9020

Lit “X” section

TBS4

T-Bar Length w/1” 1/4-20 Stud

RC5

Rotating Crossbar (Ceilings 1/4” to 2” thick )

TS1” 1/4-20 Stud

PMPerimeter Mount

TB4

T-Bar Length w/suspension clips

EMN17,18,19

EM battery pack(Non-IC-rated)

IL9020

Lit Horizontal 90° Corner

17See page 8 for full details and restrictions

18120 or 277 Volt only

19 Not available on lengths under 4’ or with 1B45 or 1B40

MountingL1R1 or L1R2

6Length intended to fi t centered between the grid for SG, TB, TBS, PMT mountings.

PMT4

T-Bar Length Perimeter Mount

4L1R1 only

5Consult factory for lengths under 2’

Confi gurationOptions

1 Values calculated from a 4’ fi xture @4000K using LW Shielding and DIM driver. For additional information please see page 2.

2 Available starting at 2’ and up.3 Not available with EMN or Lutron.

UNV120 thru 277 50/60hz capable

20 See pages 10 and 11 for full details and restrictions

Individual fi xtures, Runs and Confi gurations are supplied in nominal lengths to ensure full, even, illumination. See pages 2 thru 6 for additional details.

MIClear Lens with Microprism

DL11

Damp Location Rated

FS11

In-line FuseSS11

Separate Switching

CCEA12

CCEA approved

11See page 8 for full details and restrictions12Not available with EMN option13Consult factory

FixtureOptions

xxxx13

LED MR16 downlight

Driver DML7,8

eldoLED SOLO-drive 0-10V (Logarithmic)

DMD7,8

eldoLED DALI (Logarithmic)

DCE7,8

Lutron Eco-System

DC37,8

Lutron 3-WireDC27,8,9

Lutron 2-Wire

7See page 7 for full details8 Not available for 1’ length or with 1B45 or 1B40

9120V only10For use with E and P sensors only.

DM7,8

eldoLED SOLOdrive 0-10V (Linear)

DIM7

0-10V(Linear)

*1’ fi xture only available with 1 B35 light engine

SensorOptions

xE14, 15

Enlighted

Replace “x” with quantity

xP114, 15

Philips Daylight

xP214, 15

Philips Occ/Vac

xP314, 15

Philips Occ/Vac/Daylight

xS114, 16

Sensor Switch Daylight

xS214, 16

Sensor Switch Occ/Vac

xS314, 16

Sensor Switch Occ/Vac/Daylight

SR7,8,10

Philips Xitanium SRDALI

14 Minimum length 2’. See page 9 for full details and restrictions15For use with SR driver only16For use with DIM driver only

or

1B351

706lm/8.5Wper foot

1B301,2

603lm/7.1Wper foot

1B251,2

540lm/6.3Wper foot

1B201,2

408lm/4.7Wper foot

1B451,2,3

887lm/10.9Wper foot

1B401,2,3

802lm/9.7Wper foot

347347 Volt(consult factory)

DC5Lutron 5-Series (consult factory)

xSNnLight enabled(consult factory)

EMRRemote Micro Inverter (consult factory)

EMIntegral EM Battery Pack(consult factory)

BLSemi-Matte Black

NBLMO Symmetric

A2LMO Asymmetric 20° Wall Washer

BWLMO Batwing

A5LMO Asymmetric 5° Wall Grazer

-

-

of 15 (Rev. 04/2018)

M100LED Recessed_v[1B]3.1

In a continuing effort to offer the best product possible, we reserve the right to change, without notice, specifications or materials that in our opinion will not alter the function of the product. Specification sheets found at www.selux.us are the most recent versions and supercede all other printed or electronic versions.


M100LED Recessed

4” (101mm)

3 11/16” (94mm)

3 15/16” (100mm)

Construction:

Housing - Continuous, low copper 6063-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 12’) or Runs.

Flange - 9/16” (14mm) wide flange runs full lengths of both sides and is part of the main extruded body. Specify continuous flange (L1R1) or flush (L1R2) end cap . L1R2 does not work in T-Bar ceiling.

Geartray - Low copper 6063-T6 extruded alu-minum profile.

Shielding - Extruded, impact resistant acrylic snap in lens:- LED optimized white lens (LW)- Clear lens with microprism (MI)“LMO” refers to the Selux proprietary LED optical system - Light modulation optics. These lenses are offered in M100 behind a Satine Lens for even illumination and comfortable lit appearance.- “LMO” symmetric lens (NB)- “LMO” Asymmetric 20° wall washer (A2) - “LMO” Asymmetric 5° wall grazer (A5)- “LMO” Batwing (BW)

Mounting(s) - Spackle in (drywall), Slot grid, Decoustic, T-bar grid, Perimeter, Rotating Cross-bar and Threaded Stud Mountings (see pages 3 thru 6 for details).

Standard Luminaire lengths - All standard luminaires are supplied in nominal lengths to ensure full, even, illumination. Runs and Con-figurations are available in approximately 1/4” increments starting at the nominal 8’ fixture length. ** Individual luminaires are not joinable in the field.

Exact length luminaires - Individual lumi-naires, Runs, and Configuration are available in exact lengths to meet your project needs. Please consult factory with you requirements. ** Lens luminance may soften at the very ends of the straight sections for exact length luminaires.

L10 Joiner(s) - Runs and Configurations are supplied in multiple housing that are joined together in the field using the supplied L10 Joiner System. This allows ease of installation and ensures a uniform appearance (see page 8 for detail).

Weight: 3.2 lb. per foot.

Electrical/Performance:

LED Light Engine - Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 96% at 25,000 hours and 93% at 60,000 hours @ 25ºC per TM-21 reports. Reported L70 greater than 60,000 hours.

Delivered Lumens - Due to LED manufacturer’s tolerances the listed output has a ±5% toler-ance. For outputs based on different shielding or CCT please see photometry section at the end.

CCT - Available in 2700K, 3000K, 3500K and 4000K, tolerance within a 3-step MacAdam ellipse.

CRI - Min. 90.

All Drivers - High efficiency, constant current, soft start, Electronic Class 2 with a PFC>0.90. For more detailed information on the available drivers please see page 7.

Sensors - Selux offers a variety of integral sensor options. For details and specifications, please refer to page 9.

Thermal Performance:

Ambient Operating Temperature - Luminaires suitable for maximum ambient temperature of 35° C (95° F) for all drivers.

Luminaires are suitable for minimum ambient temperatures of:-40ºC (-40ºF) for DIM, DM, DML, and DMD drivers.-20ºC (-4ºF) for SR drivers.0ºC (32ºF) for DC2, DC3, and DCE drivers.

Luminaire Finish:

Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI.

All products undergo a five stage intensive pretreatment process where product is thor-oughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultra violet resistance for color retention.

Standard interior colors are White (WH), Black (BK), Semi-Matte Black (BL), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide.

Warranty:

5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the M100 series LED luminaire shall be free from defects in mate-rial and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see “Selux Terms and Condition of Sale.”

Certifications and Compliance: NRTL - For Dry and Damp location (I.E. cULus; cCSAus)ARRA CompliantRoHS Compliant IC-Rated *

*EMN option is Non-IC-rated

4” (101mm)

3 15/16” (100mm)

3 11/16” (94mm)

4 13/16” (122mm) LW lens shown for reference

of 15 (Rev. 04/2018)




M100LED Recessed

1. 1/4-20 Threaded rod to structure (supplied and installed by others).2. 14-20 Coupler hardware (supplied and installed by others).3. 1” 1/4-20 Stud (by Selux).4. Ø5/16” [Ø7mm] mounting hole. 5. Drywall/Sheetrock screw (Ref.)6. Drywall/Sheetrock (Ref.)7. 1/16” Plaster skimcoat (Ref.)8. Drywall/Sheetrock tape (Ref.) 9. Blocking to secure fixture (by others) 10. Electrical connection box, removable side cover for electrical

connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.

11. Luminaires ship with the brackets pre-installed. - The brackets cannot be removed until the fixture is complete-

1/2” Spackle Flange Mounting (SF1)


After Sheetrock Flange Mounting (SF3)

After drywall installation

Spackle Flange Mounting (SF1, SF2 & SF3) - Dimensions

Nominal Length

“A” O.A.L. w/o Flange

“B” End Suspensions

* “C” (Ref.) Mid. Suspension

“D” Feed Location

Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM

01 (1 ft.) 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105

02 (2 ft.) 1' - 11 7/16" 595 0' - 1 5/8" 41 1' - 8 3/16" 513 0' - 4 1/8" 105

03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54

04 (4 ft.) 3' - 11 7/16" 1205 0' - 6 1/8" 156 2' - 11 3/16" 894 0' - 2 1/8" 54

05 (5 ft.) 4' - 11 7/16" 1510 0' - 6 1/8" 156 3' - 11 3/16" 1199 0' - 2 1/8" 54

06 (6 ft.) 5' - 11 7/16" 1815 0' - 6 1/8" 156 4' - 11 3/16" 1504 0' - 2 1/8" 54

07 (7 ft.) 6' - 11 7/16" 2119 0' - 6 1/8" 156 5' - 11 3/16" 1808 0' - 2 1/8" 54

08 (8 ft.) 7' - 11 7/16" 2424 0' - 6 1/8" 156 6' - 11 3/16" 2113 0' - 2 1/8" 54

*Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.



After Sheetrock Flange Mounting (SF3)

of 15 (Rev. 04/2018)




M100LED Recessed

1. 9/16” Slot grid (shown as ref.) 2. Support wire to structure

(supplied and installed by others).3. 1/4-20 Threaded rod to structure

(supplied and installed by others).4. 1/4-20 Coupler hardware

(supplied and installed by others).5. 1” 1/4-20 Stud (by Selux).6. Ø5/16” [Ø7mm] mounting hole.

Slot Grid Mounting (SG) 9/16” Slot Grid Mounting (SG) (Wire Suspension or 1/4-20 Stud)

1. 1/4-20 Threaded rod to structure (supplied and installed by others).2. 1/4-20 Coupler hardware (supplied and installed by others).3. 1” 1/4-20 Stud (by Selux).4. Ø5/16” [Ø7mm] mounting hole.5. 1/2” wide alum. angle runs the entire length of fixture to block view into

plenum area from below fixture.6. Suitable for Decoustic® ceiling panel installations with panels up to 2” thick

(supplied and installed by others). Other ceiling systems possible, please consult factory. Decoustic® is a registered trademark of Decoustics Ltd. Corporation.

Decoustic Mounting (DC) Decoustic Mounting (DC) (Panels up to 2” thick)

Decoustic Mounting (DC) - Dimensions

Nominal Length

“A” Housing Length





01 (1 ft.) 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105

02 (2 ft.) 1' - 11 7/16" 595 0' - 1 5/8" 41 1' - 8 3/16" 513 0' - 4 1/8" 105

03 (3 ft.) 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54

04 (4 ft.) 3' - 11 7/16" 1205 0' - 6 1/8" 156 2' - 11 3/16" 894 0' - 2 1/8" 54

05 (5 ft.) 4' - 11 7/16" 1510 0' - 6 1/8" 156 3' - 11 3/16" 1199 0' - 2 1/8" 54

06 (6 ft.) 5' - 11 7/16" 1815 0' - 6 1/8" 156 4' - 11 3/16" 1504 0' - 2 1/8" 54

07 (7 ft.) 6' - 11 7/16" 2119 0' - 6 1/8" 156 5' - 11 3/16" 1808 0' - 2 1/8" 54

08 (8 ft.) 7' - 11 7/16" 2424 0' - 6 1/8" 156 6' - 11 3/16" 2113 0' - 2 1/8" 54



Slot Grid Mounting (SG) - Dimensions

Nominal Length

“A” Housing Length




“E” Grid Spacing

Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet

02 (2 ft.) 1' - 11 7/16" 595 0' - 1 5/8" 41 1' - 8 3/16" 513 0' - 4 1/8" 105 2’ Center to Center





of 15 (Rev. 04/2018)




M100LED Recessed

T-Bar Mounting (TB) T-Bar with Stud Mounting (TBS)

T-Bar with Suspension Clips (TB) (9/16” or 15/16” grid)

T-Bar with 1/4-20 Stud (TBS) (9/16” or 15/16” grid)

Perimeter Mount T-Bar Length (PMT) (Recessed Wall Mounting)Perimeter Mounting T-Bar Length (PMT)

1. Support wire to structure (supplied and installed by others).2. Spring steel suspension clips located approximately every 4 ft.

(supplied by Selux).3. 9/16” T-bar grid (shown as ref.)3a. 15/16” T-bar grid (shown as ref.)4. 1/4-20 Threaded rod to structure (supplied and installed by others).5. 1/4-20 Coupler hardware (supplied and installed by others).6. 1” 1/4-20 Stud (by Selux). 7. Ø5/16” [Ø7mm] mounting hole.

**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.

T-Bar (TB & TBS) and Perimeter Mount (PMT) - Dimensions

Nominal Length

“A” O.A.L. with Flange

“A1” O.A.L. without Flange


“BB” (TB mtg.) Suspension

Clips

** “C” (Ref.) Mid. Suspension


“E” Grid Spacing

“F” Wall Angle

Feet/Inch MM Feet/Inch MM Feet/Inch MM Quantity Feet/Inch MM Feet/Inch MM Feet Feet/Inch MM

*02 (2 ft.) 1' - 11 13/16" 605 1' - 10 15/16" 583 0' - 4 1/2" 114 4x 1' - 2" 355 0' - 1 1/8" 28 2’ Center to Center 1' - 11 13/16" 605

*04 (4 ft.) 3' - 11 13/16" 1215 3' - 10 15/16" 1193 0' - 6 1/8" 156 6x 2' - 10 11/16" 882 0' - 2 1/8" 54 4’ Center to Center 3' - 11 13/16" 1215


*06 (6 ft.) 5' - 11 13/16" 1825 5' - 11" 1803 0' - 6 1/8" 156 6x 4' - 10 3/4" 1492 0' - 2 1/8" 54 6’ Center to Center 5' - 11 7/8" 1825


*For other lengths consult factory

8. Steel Wall Bracket with provision for 1/4-20 fasteners (hardware to code by others).

9. 2” 1/4-20 Stud (by Selux).10. 1/2” x 1” Alum. wall angle allows a gap between flange

and wall to create shadow line allowing for uneveness of wall. Provision for #10 screws supplied approximately every 2 ft. (hardware to code by others).

of 15 (Rev. 04/2018)




M100LED Recessed

Rotating Crossbar Mounting (RC) 1/4-20 Threaded Stud Mounting (TS)

Rotating Crossbars (RC) (1/4” to 2” thick ceiling)

1/4-20 Threaded Stud (TS) (1” Threaded Stud)

Perimeter Mounting (PM)Perimeter Mount (PM) (Recessed Wall Mounting)

8 3/8

1. Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling thickness of 1/4” to 2”.

2. 1/4-20 Threaded rod to structure (supplied and installed by others).3. 1/4-20 Coupler hardware (supplied and installed by others).4. 1” 1/4-20 Stud (by Selux).5. Ø5/16” [Ø7mm] mounting hole.

**Dimension(s) rounded to the nearest 1/16” with a ± 1/16 (1mm) tolerance.

Rotating Crossbar (RC), Threaded Stud (TS), and Perimeter Mountings (PM) - Dimensions

Nominal Length

“A” O.A.L. with Flange

“A1” O.A.L. without Flange


** “C” (Ref.) Mid. Suspension


“E” Wall Angle

Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM

*01 (1 ft.) 1' - 1 3/16" 335 1' - 5/16" 313 0' - 1 5/8" 41 0' - 9 1/8" 231 0' - 4 1/8" 105 1' - 1 3/16" 335

02 (2 ft.) 1' - 11 13/16" 605 1' - 10 15/16" 583 0' - 4 1/2" 114 1' - 2" 355 0' - 1 1/8" 28 1' - 11 13/16" 605

03 (3 ft.) 3' - 1 3/16" 945 3' - 5/16" 923 0' - 6 1/8" 156 2' - 1/8" 612 0' - 2 1/8" 54 3' - 1 3/16" 945

04 (4 ft.) 3' - 11 13/16" 1215 3' - 10 15/16" 1193 0' - 6 1/8" 156 2' - 10 11/16" 882 0' - 2 1/8" 54 3' - 11 13/16" 1215

05 (5 ft.) 4' - 11 13/16" 1519 4' - 10 15/16" 1497 0' - 6 1/8" 156 3' - 10 11/16" 1187 0' - 2 1/8" 54 4' - 11 13/16" 1519

06 (6 ft.) 5' - 11 13/16" 1825 5' - 11" 1803 0' - 6 1/8" 156 4' - 10 3/4" 1492 0' - 2 1/8" 54 5' - 11 13/16" 1825

07 (7 ft.) 6' - 11 13/16" 2129 6' - 10 15/16" 2107 0' - 6 1/8" 156 5' - 10 11/16" 1796 0' - 2 1/8" 54 6' - 11 13/16" 2129

08 (8 ft.) 7' - 11 13/16" 2434 7' - 10 15/16" 2412 0' - 6 1/8" 156 6' - 10 11/16" 2101 0' - 2 1/8" 54 7' - 11 13/16" 2434

*RC mounting, consult factory for lengths under 2’

6. Steel Wall Bracket with provision for 1/4-20 fasteners (hard-ware to code by others).

7. 2” 1/4-20 Stud (by Selux).8. 1/2” x 1” Alum. wall angle allows a gap between flange and

wall to create shadow line allowing for uneveness of wall. Provision for #10 screws supplied approximately every 2 ft. (hardware to code by others).

of 15 (Rev. 04/2018)




M100LED Recessed

Drivers:

Wiring Diagrams

0-10V linear dimming (DIM)Luminaires supplied with drivers offering the capability of either normal switched operation or 0-10V dimming for linear dimming curve. Fixtures ship wired for dimming. For on/off functionality, simply cap the dimming leads. Minimum dimming level preset at factory to 1%. (Due to size constraints, 1’ luminaires are supplied with a driver from a different manufacturer than 2’ and above luminaires. For details, please consult factory.)

eldoLED SOLOdrive 0-10V linear dimming (DM)Luminaires supplied with SOLOdrive 0-10V dimming driver for linear dim-ming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.

eldoLED SOLOdrive 0-10V logarithmic dimming (DML)Luminaires supplied with SOLOdrive 0-10V dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.

eldoLED SOLOdrive DALI dimming (DMD)Luminaires supplied with SOLOdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to 1%. For “dim to dark” (down to 0.1%), please consult factory.

* For control recommendations for eldoLED drivers, please consult eldoLED.

LUTRON 2-wire dimming (DC2)Luminaires supplied with Hi-lume 2-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.

LUTRON 3-wire dimming (DC3)Luminaires supplied with Hi-lume 3-wire dimming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.

LUTRON Ecosystem dimming (DCE)Luminaires supplied with Hi-lume EcoSystem (4 wire, digital link) dim-ming driver programmed for Constant Current Reduction (CCR). For Pulse Width Modulation (PWM) dimming, please consult factory. Minimum dimming level down to 1%.

* For control recommendations and system layout for Lutron drivers, please contact Lutron.

Philips Xitanium Sensor Ready DALI dimming (SR)Luminaires supplied with Xitanium SR dimming driver programmed for Constant Current Reduction (CCR). Minimum dim level down to 5%. For use with E and P sensors only.

Sensor Wiring Diagrams

standard0-10V linear (DIM) 0-10V linear eldoLED SOLOdrive (DM)0-10V logarithmic eldoLED SOLOdrive (DML)DALI eldoLED SOLOdrive (DMD)Philips SR DALI (SR)

DIM, DM, DML, DMD & SR

DALIDALI

ENLIGHTEDOR PHILIPSSENSOR

ELDO 0-10V

SENSORSWITCH

PHILIPS XR

SR (+)SR (-)

(+)(-) 0-10V AUX (+)

AUX (-)

Driver Quantity

1 ft. 2 ft. 3 ft. 4 ft. 5 ft. 6 ft. 7 ft. 8 ft. RUN

DIM 1 1 1 1 2 2 2 2Approximately 2 drivers per 4 ft.

DM, DML, & DMD drivers N/A 1 1 1 1 1 2 2Approximately 2 drivers per 4 ft.

DC2, DC3, & DCE drivers N/A 1 1 1 2 2 2 2 Consult Factory

*For SR driver count, please consult factory*For inrush and control current, please refer to the driver manufacturers’ spec sheets.

of 15 (Rev. 04/2018)




M100LED Recessed

Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the hot wire for each feed. (supplied with an 8A slow burn fuse).

Damp Location (DL) - Luminaires are suitable for use in damp location(s). Examples of such locations include protected areas under canopies, marquees, roofed porches, and similar locations where the fixture(s) are protected from direct contact with rain, snow, or excessive moisture (such as ocean spray). Interior locations include areas subject to moderate degrees of moisture, such as basements and certain barns and cold storage buildings. All solder points on LED boards are conformal coated. The phosphor layer of the LEDs is free of coating to avoid hazing.

*For Damp Location with sensors, please consult factory.

Separate Switching (SS) - Luminaires available with separately switched 4’ (nominal) sections starting at 7’ and up. Luminaire is in-tended to be wired to the same panel/breaker (not intended for Emer-gency use).

- To specify this option, the number of separately switched sections and locations of these sections must be provided at time of order.

* If the project requires different separate switching than outlined above please consult the factory.

*For Separate Switching with sensors, please consult factory.

Joiner System - standard for Runs and Configurations

90° Elbow on top of the housing (7/8" feed hole)

3/8" flexible metal conduit (6' long)

6" leads

Straight fitting

Flex Whip - standard for recessed fixtures

EMN (Emergency Battery Pack)* - Emergency battery pack is avail-able starting at the 4’ nominal length and up in 2’ nominal sections. The battery pack is housed in a box on the top of the luminaire and is fully accessible from below the ceiling.

- For individual luminaires, the lit section will be located on the feed end of the fixture. If a different location is needed please consult the fac-tory.

- For Runs, please specify location of lit section (in 2’ nominal sections).

*Luminaires with EMN option are Non-IC-rated*For EMN with sensors, please consult factory.

Emergency Circuit (EC) - Luminaires with EC option compliant to UL 924 listed emergency luminaire. EC luminaires are intended to be wired to separate panels/breakers for emergency use.

- For 1’ to 6’ nominal luminaires, the entire fixture is wired for operation on emergency circuit.

- For 7’ and up nominal luminaires, the first 4’ nominal length is wired for operation by a separate EM circuit by default to meet the required “Life Safety Code” (NFPA 101).

**If a different configuration is needed please consult the factory.*For EC with sensors, please consult factory.

2 3/4”(70mm)1’-5”(432mm)

EMN Model # Input Operation Time Lumen Output CCT Shielding

IOTA ILB-2412 2.5W Max. 90 Minutes *966 lm **4000K LW

*Lumen output is fixed and the same for all light engines**See page 13 for CCT multiplier

of 15 (Rev. 04/2018)




M100LED Recessed

Sensor Ordering Chart

Quantity Sensor Settings*

x Number of Sensors E Enlighted FS-D22

P Philips Easy Sense SNS102

S Sensor Switch MSD EZ

1 Daylight

2 Occupancy/Vacancy

3 Daylight/Occupancy/Vacancy

* Settings not available with Enlighted

Standard Sensor Placement - for other placement options, please consult factory. For functionality and limitations, please see sensor details above.

Lens Aluminum Sensor Plate -to be painted same as fixture unless specified otherwise

Qty 1 Sensor - Beginning Qty 2 Sensor - Beginning and End (9’ fixtures and longer)

Qty 3+ Sensor - For spacing between sensors, please consult the sensor manufacturer

Beginning of Run

Notes: 1. For spacing between sensors, please consult the sensor manufacturer. 2. Exact sensor placement and coverage will be defined by approved factory drawing. 3. Sections controlled by sensors may not be symmetrical - consult factory for layout.

3” (76mm)

Enlighted FS-D22 (E)Occupancy/vacancy, daylight harvesting, plus the Internet of Things (IoT) data collection and reporting. For full details, please see FS-D22 spec sheet on the Enlighted website. Must be paired with Philips Xitanium SR driver (SR driver selection). Commissioning by Enlighted. *Please contact Enlighted for complete details prior to specifying. *Sensor can control up to 4 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.

Philips EasySense SNS102 (P)Occupancy/vacancy and daylight harvesting. Sensor can be programmed on-site via NFC or IR using Android app only, by others. For full details, please see the SNS102 spec sheet on the Philips website. Must be paired with Philips Xitanium SR driver (SR driver selection). Wall dimming via wireless wall switch from Philips/Illumra (www.illumra.com/easysense). **Please contact Philips for complete details prior to specifying. *Sensor can control up to 10 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.

Sensor Switch MSD EZ (S)Occupancy/vacancy and daylight harvesting. For full functionality and programming options, select settings option 3. If a different settings option is selected, other settings may be unavailable. For full details, please see MSD EZ spec sheets on the Sensor Switch website. Must be paired with eldoLED 0-10V driver (DIM driver selection). Manual control of dimming not available with MSD EZ sensor. *Please contact Sensor Switch for complete details prior to specifying.*Sensor can control up to 30 drivers. Please refer to driver quantity chart on page 7. Multiple sensors may be required for longer lengths.

Occupancy Vacancy Daylight Harvesting Driver Compatibility

Enlighted FS-D22 (E) See Enlighted’s website for full capabilities SR

Philips EasySense SNS102 (P) √ √ √ SR

Sensor Switch MSD EZ (S) √ √ √ DIM

Factory Presets - Sensors come from the sensor manufacturer with factory presets for each of the settings in above chart. Please see sensor manufacturers’ spec sheets for details on presets and re-programming.

Commissioning - Commissioning of sensors and installation by others. Contact sensor manufacturer for details and costs associated with commissioning the system prior to specification of sensors.

* Lit section will be the fixture length minus 3” for sensor plate.

Fixture Length

Lit Section*

3 15/16”” (100mm)

of 15 (Rev. 04/2018)




M100LED Recessed

Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions, please consult the factory.

The minimum standard lengths for “L” shapes:- IL90 or V90 open shapes is 4’ x 4’ nominal (example: leg, 90, leg)- IL90 or V90 closed shapes is 6’ x 6’ nominal (example: 90, leg, 90)( Exception is that the IL90 & V90’s can be joined directly to provide a 4’ x 4’ nominal shape)

*For sensors in configurations, please consult factory.

Standard Recessed (L10) shapes/configurations:

The minimum standard lengths for “T” & “X” shapes:- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side- IX90 = 8’ nominal for either direction

Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.

Project Specific Recessed (L10) shapes/configurations:

Recessed (L10) Lit Corner and Section - Dimensions

IL90 V90 IT90 IX90


“A” Housing (Outside) 2' - 2 1/16" 662

“A1” Housing (Inside) 1' - 10 1/8" 562

“B” Housing (Outside) 1' - 11 1/2" 698

“B1” Housing (Inside) 2' - 3 1/2" 597

“C” Housing (Inside) 2' - 2 1/16" 662

* “C1” Ref. 2' - 1/8" 612

“D” Housing 4' - 3/16" 1224

* “D1” Ref. 2' - 1/8" 612

“E” Housing 4' - 3/16" 1224

* “E1” Ref. 2' - 1/8" 612


of 15 (Rev. 04/2018)




M100LED Recessed

Listed below are the minimum lengths and details for standard shapes. These standard shapes can be combined with each other and/or the standard luminaire lengths, ensuring full even illumination. If you have any questions please consult the factory.

The minimum standard lengths for “L” shapes:- IL90 or V90 open shapes is 4’ x 4’ nominal (example, leg, 90, leg)- IL90 or V90 closed shapes is 6’ x 6’ nominal (example, 90, leg, 90)( Exception is that the IL90 & V90’s can be joined directly to provide a 4’ x 4’ nominal shape)

*For sensors in configurations, please consult factory.

Standard Recessed (L1R1/2) shapes/configurations:

The minimum standard lengths for “T” & “X” shapes:- IT90 = 4’ nominal on the short leg and 8’ nominal on the long side- IX90 = 8’ nominal for either direction

Selux is capable of supplying a wide range of project solutions including different shapes, angles, and sizes to meet the project requirements. Due to the complex nature of these project specific layout(s) we ask that you please consult the factory with the project requirements for review.

Project Specific Recessed (L1R1/2) shapes/configurations:

Recessed (L1R1/R2) Lit Corner and Section - Dimensions

IL90 V90 IT90 IX90


“A” w/Flange (Outside) 2' - 2 1/2" 673

“A1” Housing (Outside) 2' - 2 1/16" 662

“B” w/Flange (Inside) 1' - 9 11/16" 551

“B1” Housing (Inside) 1' - 10 1/8" 562

“C” Housing (Inside) 2' - 3 1/2" 698

“C1” Housing (Outside) 1' - 11 1/2" 597

“D” w/Flange 2' - 2 1/2" 673

“D1” Housing 2' - 2 1/16" 662

* “D2” Ref. 2' - 1/8" 612

“E” Housing 2' - 1/8" 612

* “E1” Ref. 4' - 3/16" 1224

“F” Housing 4' - 3/16" 1224

* “F1” Ref. 2' - 1/8" 612


of 15 (Rev. 04/2018)




M100LED Recessed

Photometry

254

507

761

1014

1

2

Maximum Candela = 1014 Located At Horizontal Angle = 0, Vertical Angle = .5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

LW Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-LW-X-04-XX-UNVReport #: 11685024.3 Delievered Lumens: 2822 Input Watts: 34WEfficacy: 83 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 4000KCRI: 95.7Max Candela: 1014 @ .5° from VerticalSpacing Criterion (0-180): 1.28 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.38

490

980

1469

1959

12

Maximum Candela = 1959 Located At Horizontal Angle = 0, Vertical Angle = 1# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

MI Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-MI-X-04-XX-UNVReport #: 11685024.07 Delivered Lumens: 2963 Input Watts: 34WEfficacy: 87 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 4000KCRI: 95.7Max Candela: 1959 @ 1° from VerticalSpacing Criterion (0-180): 1.22 Spacing Criterion (90-270): 0.88 Spacing Criterion (Diagonal): 1.04

of 15 (Rev. 04/2018)




Photometry

NB Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-NB-04-XX-UNVReport #: 12236853.04 Delievered Lumens: 2974 Input Watts: 33.28 WEfficacy: 89 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 4000KCRI: 95.7Max Candela: 1318.24 @ .5° from VerticalSpacing Criterion (0-180): 1.28 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.38

M100LED Direct

330

659

989

1318

1

2

Maximum Candela = 1318.24 Located At Horizontal Angle = 90, Vertical Angle = .5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

A2 Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-A2-X-04-XX-UNVReport #: 12236853.0104 Delivered Lumens:2904 Input Watts: 33.18 WEfficacy: 88 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 3950KCRI: 95.7Max Candela: 1959 @ 1° from VerticalSpacing Criterion (0-180): 1.22 Spacing Criterion (90-270): 0.88 Spacing Criterion (Diagonal): 1.04

357

715

1072

1430

12

Maximum Candela = 1429.757 Located At Horizontal Angle = 0, Vertical Angle = 15.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

of 15 (Rev. 04/2018)




Photometry

360

720

1080

1440

1

2

Maximum Candela = 1440.25 Located At Horizontal Angle = 0, Vertical Angle = 5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

A5 Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-A5-04-XX-UNVReport #: 12236853.020440 Delievered Lumens: 2974 Input Watts: 33.28 WEfficacy: 89 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 4000KCRI: 95.7Max Candela: 1440.25 @ .5° from VerticalSpacing Criterion (0-180): 1.28 Spacing Criterion (90-270): 1.24 Spacing Criterion (Diagonal): 1.38

M100LED Direct

253

506

759

1012

1

2

Maximum Candela = 1012.29 Located At Horizontal Angle = 90, Vertical Angle = 16.5# 1 - Vertical Plane Through Horizontal Angles (90 - 270)# 2 - Vertical Plane Through Horizontal Angles (0 - 180)

BW Optics / 34W LED / 4000K CCT

Catalog #: L10-1B35-40-BW-X-04-XX-UNVReport #: 12236853.030440 Delivered Lumens:2843 Input Watts: 33.22 W Efficacy: 86 Power Factor: 0.991 Total Harmonic Distortion: 9.30 CCT: 3950KCRI: 95.7Max Candela: 1012.29 @ 1° from VerticalSpacing Criterion (0-180): 1.22 Spacing Criterion (90-270): 0.88 Spacing Criterion (Diagonal): 1.04

of 15 (Rev. 04/2018)




M100LED Recessed

Photometry

CCT and CRI multipliers apply to the photometry, IES files, and per foot values listed on page one (light engine).

Light engine multiplier supplied for per foot values listed on page one (light engine).

4000K3500K3000K2700K

Light Engine Lumens Wattages1B45 1.258 1.2851B40 1.137 1.1401B35 1.000 1.0001B30 0.855 0.8381B25 0.766 0.7401B20 0.578 0.552

LWMINBA2A5BW

1.0611.0291.0541.008

Lens Multiplier1.0001.050

L100 LED Direct Photometry Multiplier Table

CCT Multiplier

Light Engine Multiplier

1.0000.9720.9630.931

m100 led recessed [l1rx] · pdf fileseparate led mr16 downlight switching. ccea. 12. ccea...

Documents