maple valley fire lz kit set up. ojectives this presentation is intended to provide a guide on how...
TRANSCRIPT
Maple Valley FireLZ Kit Set Up
Ojectives
• This presentation is intended to
provide a guide on how to use, set
up, and restore the new LZ kits.
LZ Kit Storage• The LZ kits will be
placed on Engines
80, 81, and 83.
• The kits will be
stored in the
Officer’s upper
rear compartment
on all three
engines
LZ Kit Layout• Each LZ kit will
include:
• 5-Red Turboflare
lightheads
• 1-100’ Tape
Measure
• 1-Caribiner
(attached to the
tape)
• 1-LZ layout guide
Turboflare Operation• Each
Turboflare has
a switch on the
side of the unit
• Simply press
the switch to
turn each unit
on and off.
Turboflare Maintenance
• The new Turboflare kits utilize
lightheads powered by AA batteries.
• When the lighthead becomes dim,
the 4 AA batteries will require
replacement
Turboflare Maintenance• To replace the batteries:
• Remove the 2 screws next to
the switch
• Remove switch cover
• Remove batteries
• Replace batteries following
diagram on bottom of
lighthead
• Replace cover
• Check operation
Deployment• To set up an LZ:
– 1. Choose LZ
area
– 2. Remove LZ
kit from Engine
– 3. Place LZ kit
in center of LZ
Deployment
• Setting up LZ (Continued):
• 4. Remove lightheads
and 100’ tape
• 5. Close and latch
storage box lid
• 6. Connect tape to Kit
handle via carabiner
DeploymentSetting up LZ
(Continued)
7. Walk out appropriate
distance for LZ
• 30 feet for a 60 foot
LZ
• 50 feet for a 100
foot LZ
• 100 feet for a 200
foot LZ
Deployment8. Turn on and set down
first lighthead
9. Using the tape as a
guide, walk a full circle
at the appropriate
distance from the LZ
center, turning on and
dropping lightheads as
you go.
Deployment
When complete, the
lightheads should
create a ring outlining
the proposed LZ.
Reservice
When operations are
complete:
1. Gather all 5 lightheads
2. Place all 5 lightheads in
the storage box in 2
separate stacks as shown
Reservice
3. Fold tape handle into
stowed position
4. Store tape on top of
lighthead stacks
5. Close and latch lid and
replace on engine.
LZ Reminders
1. Contact Airlift on State
Ops 1
• Line of sight channel
• May not work until
they are close
LZ Reminders2. Give LZ Report
• Standard LZ’s have
report in LZ book
• Follow similar
template if landing
at non-standard
location:
• Dimensions
• Surface
• Hazards
• Special
LZ Reminders3. Report Airlift’s
safe landing to
dispatch
4. Assist with
patient
packaging and
loading
5. Report Airlift’s
departure
Watch for rotor wash debris during take off and landings!
Other UsesTurboflares were originally
designed as an alternative
to incendiary flares.
Besides LZ set ups, they
can be used for any
purpose you would use a
flare for such as marking
driveways or traffic control
Other UsesAlong with the new LZ
kits, we are also adding
one lighthead to A80, A81,
and A83 to provide a
safer, faster, more
efficient way to mark
problem driveways during
responses. Simply push
the button and place on
the ground to mark the
driveway.
Conclusion
• The new Turboflare landing zone kits
are very similar to the current kit we
operate
• While its primary purpose is LZ set
up, feel free to use them for any use
you see fit