marine transmissions - perkins · pdf fileusers (and not twin disc , incorporated) to provide...
TRANSCRIPT
![Page 1: MARINE TRANSMISSIONS - Perkins · PDF fileusers (and not Twin Disc , Incorporated) to provide and install guards or safety devices which may be required by recog](https://reader031.vdocument.in/reader031/viewer/2022030505/5ab252997f8b9a6b468d6368/html5/thumbnails/1.jpg)
BULLETIN 319-S-02
-
MARINE TRANSMISSIONS 52 to 288 kW (70 to 386 hp)
)
(Model MG-S02-1 Shown with Optional Housing Flange and Torsional Coupling)
TWIN DISC, INCORPORATED, RACINE, WISCONSIN 53403 , U.S.A. ~) 1989 .Twin Disc. Incorpora ted
![Page 2: MARINE TRANSMISSIONS - Perkins · PDF fileusers (and not Twin Disc , Incorporated) to provide and install guards or safety devices which may be required by recog](https://reader031.vdocument.in/reader031/viewer/2022030505/5ab252997f8b9a6b468d6368/html5/thumbnails/2.jpg)
MG-502 and MG-502·1 (Shown with optional housing flange ond torsional drive plate)
'Maximum allowable input speed : With Diesel Engines 4000 rpm With Gasoline Engines 4200 rpm
.Unlessgranted prior written opproval.
Lighter and 1/2 the length of comparable capacity transmissions 10° output shaft down angle-provides for near level engine installation Permits lower deck and more usable room Oil controlled clutch engagement
Carburized, hardened, conical helical gears No external plumbing Built with jig-bore accuracy
Identical forward and reverse ratios: MG-502-2.47:1; MG-502-1-1.54:1and 2.00:1 Unlimited engine flywheel housing adaptability Identical performance forward or reverse-provides either left or right-hand propeller rotation with identical right-hand rotation engines
QUIET OPERATION ... MORE ON-BOARD LIVING AREA . . . GREATER DESIGN FLEXIBILITY.
The MG-S02 and MG-S02-1 use conical involute gearing to provide a 10° down angle. This feature eliminates the need for engine installation at severe high angles and provides easier installation and more on-board living space.
Identical performance and ratios in forward or reverse eliminate the need for opposite rotation engines.
m
Torsional Drive Plate MG-50281 R~ Minimum Axial Hub Length (see note bele
-: Optional SAE NO.3 ~ Housing Flange I, , :
144 mm (5.7") . " >. + t -~
'" ~O23 1 mm (9.1")_ ~~~Pllng
~, 244 mm (9.6") Flange .... ~
~ri
UseCertified Print for Installation
MODEL
MG-502
MG-502· '
These lightweight, high-capacity marine transmissions permit the use of higher powered engines that are requ ired forthe best vesselperformance.Theseunits all have helical gears and torque capacity to accommodate most mid-range, high-speed diesels and high-performance gasoline engines. The MG-S02-1 incorporates design and material improvements which allows itsuse at higher Pleasure Craft ratings than the MG-S02.
Unlike most marine countershaft arrangements, this transmission with 10° down angle offers broader design flexibility for marine architects.
Optional Equipment Includes housing flange-SAE NO.3 (XB5690) or special adapter (XA71S7) 235 mm (9.2S") B.C.; prop coupling flange-SAE No. 2S (XB3431) ; and torsional couplingsSAE No. J620C- 292 mm (11.5") (A7052A), polyurethane element (A7559), or 292 mm (11 .5") elastomeric (PM8756A). NOTE: Customer sourced torsional drive plates other than from Twin Disc must have a minimum axial hub length of 35 mm (1.38") when used on MG-502's and a minimum hub length of 45 mm (1.75") when used on MG-502-1's.
Heat Exchanger Available from Twin Disc. Customers who wish to furnish their own heat exchanger should contact the nearest Twin Disc or marine engine distributor for exchanger specifications. When ordering, specify if raw or fresh water is to be used in the heat exchanger.
![Page 3: MARINE TRANSMISSIONS - Perkins · PDF fileusers (and not Twin Disc , Incorporated) to provide and install guards or safety devices which may be required by recog](https://reader031.vdocument.in/reader031/viewer/2022030505/5ab252997f8b9a6b468d6368/html5/thumbnails/3.jpg)
MG·502·1 'I
DRAWING NUMBER RATIOS
APPROX. DRY
WEIGHT
X9994A 2.47:1 70 kg (155lbs)
X9994C 1.54:1,2.00:1 70 kg (155lbs)
MG-502-1 and MG-502 Intermediate Duty
203kW Ratio(272)
1.54:1 .".
" ~ 121 kW go (162) e? o ;. 69 kW ~ (92).. o ~
-' ;;; 1200 2100 3600
Input speed (RPM)
172kW Ratio(230)
2.00:1 ~ ~ 104 kW :- (140)
5 ;. 60 kW5 (80)
~ -' ;;; 1200 2100 3600
Input speed (RPM)
1~1~~ Ratio 2.47:1
~ ~ 88kW go (118) e
i:~ 52kW (70) ..
~ o -' ;;; 1200 2100 3600
Input speed (RPM)
For Service Classification Definit ions see back cover.
MG-502-1 and MG-502 Pleasure Craft (Planing Hull)
288kW Ratios(386) 1.54:1 2.00:1-; 201 kW
o (270) Q.
"e? o ;. 101 kW ~ (135).. o ~
-' ;;; 1400 2800 4000
Input speed (RPM)
224kW Ratio(300)
2.47:1 .". ; 168kW g, (225)
~ o
5 J: - 84kW
(112)
o ~
...J
;;; 1400 2800 4000 Input speed (RPM)
MG-502-1 and MG-502 Continuous Duty
75kW (100) 66kW
(89)
Ratios 1.54:1
-; o
56kW (75)
2.00 :1 2.47 :1
Q.
"e? o ;.
5 ~ o ...J ;;; 1800 2100 2400
Input speed (RPM)
MG·502 and MG·502·1 Power Train
![Page 4: MARINE TRANSMISSIONS - Perkins · PDF fileusers (and not Twin Disc , Incorporated) to provide and install guards or safety devices which may be required by recog](https://reader031.vdocument.in/reader031/viewer/2022030505/5ab252997f8b9a6b468d6368/html5/thumbnails/4.jpg)
Often called "Work Boat Duty," these marine transmission applications are expected to operate continuously at full engine governed speed .The propulsion engine power setting must be known and must be within the marine transmission 's allowable input rating for continuous day long or around the clock service.
Most displacement hull vessels are powered for Continuous Duty service. However, the actual engine (and marine transmission) power loading depends on:
a. The propeller used b. The vessel's work assignment c. The captain's choice of throttle
setting during continuous service
Twin Disc recommends that all displacement and semi-displacement hull commercial applications be classed as Continuous Duty usage of the marine transmission .
Examples: Fishing trawlers Purse seiners Lobster boats and crab boats Tugs Towboats Buoy tenders Offshore supply boats Ferries Research vessels Ocean freighters
Pleasure or Commercial usage of planing or semi-displacement hull craft can qualify for Intermediate Duty Service Classification if full throttle operation will average only a few hours per day with major portion of usage at partial throttle and total annual usage will be 2000 hours or less.
Examples: Long Range Pleasure Cruisers Sportfish Charter Boats Party Fishing Boats Crew Boats Harbor and Coastal Patrol Boats Search and Rescue Boats Fire Boats
Maximum power capacity is intended only for personal use, planing hull pleasure craft where full engine throttle operation will be less than 5% of total timewith balance of time at 87% of full throttle engine rpm or less. Marine transmissions used in long-range pleasure cruisers, sport fish charters or any commercial service should not be selected according to Pleasure Craft Service Classification .
Disregarding propulsion system torsional compatibility could cause damage to components in the drive train resulting in loss of mobility. At minimum, system incompatibility could result in gear clatter at low speeds .
The responsibility for ensuring that the torsional compatibility of the propulsion system is satisfactory rests with the assembler of the drive and driven equipment.
Torsional vibration analysis can be made by the engine builder, marine survey societies, independent consultants and others. Twin Disc is prepared to assist in finding solutions to potential torsional problems that relate to the marine transmission.
TWIN DISC , INCORPORATED Racine, Wisconsin 54303, U.S .A . England South Africa Singapore Hong Kong Australia TWIN DISC INTERNATIONAL.S.A. 1400 Nivelles, Belgium
IMPORTANT NOTICE: Twin Disc. Incorporated reminds users of these products that their safe operation depends on use in compliance with engineering information provided in this catalog. Users are also reminded that safe operation depends on proper installation , operation and routine mainte
nance and inspection under prevailing conditions. It is the responsibility of users (and not Twin Disc , Incorporated) to provide and install guards or safety devices which may be required by recognized safety standards or by the Occupational Safety and Health Act of 1970 and its subsequent provisions .
BULLETI~ j 19-5-02 3M-S-S9 PRINTED I:-J U:-J ITE D STATES OF AMERICA