marley eternit lincoln clay pantile brochure
TRANSCRIPT
2 Lincoln clay pantiles
Lincoln combines the bold and beautiful curves of traditional clay pantiles with all the installation simplicity and speed required for today’s roofs.
This means that Lincoln affords the rich appeal of natural, clay pantiled roofs, a thin leading edge and a beauty that matures over time.
As well as quick and easy installation, Lincoln can be installed to meet the latest fixing requirements of BS 5534 and the NHBC technical standards, without compromising tradition.
Lincoln clay pantiles
All factories certified to ISO 9001, ISO 14001
Lincoln pantiles are available with a comprehensive range of clay fittings and accessories to give a traditional finish. Additionally, many of these components can be combined with our Universal range of accessories and fittings to offer a complete dry fix and maintenance-free solution.
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 3
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 54 Lincoln clay pantiles
Lincoln Rustic RedSemi-sanded finish
Lincoln Natural RedSmooth finish
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 76 Lincoln clay pantiles
Tile features and technical data
Lincoln key features> traditional profile> easy to install (open-gauge design)> low minimum pitch 17.5°> BS 5534 compatible
Key Raised and protected blind nail hole
Raised and protected head and side locks
SoloFix clip recess
Extended weather bars over the roll for low pitch protection
Wide channel for water run-off
Raised ridge to guard against wind-driven rain
Open-gauge design for a flexible fit
Traditional s-curve profile
Thin leading edge
Hidden/cloaked interlock
The Lincoln clay pantile features a completely open-gauge design, making it quick and easy to install.For full technical data and advice, please contact our Technical Advisory Service on 01283 722588
A
D
B
E
C
Key SoloFix clip ‘pocket’ for a flush fit
Batten locator to avoid rocking
Deep nibs for ease of setting out and fixing
Double anti-capillary bars to prevent water ingress
K
N
L
ML
M
F
G
H
I
I
J
Technical dataSize of tile 370 x 247mm
Minimum pitch* 17.5° (120mm headlap) 22.5° (75mm headlap)
Maximum pitch 70°
Minimum headlap 75mm
Maximum gauge 295mm
Cover width 222mm (nominal)
Covering capacity 15.3 tiles/m2 at 75mm headlap (net) 18.0 tiles/m2 at 120mm headlap
Weight of tiling 43.0 kg/m2 at 75mm headlap (approx.) 50.4 kg/m2 at 120mm headlap
Battens required 3.4 lin.m/m2 at 75mm headlap (net) (net) 4.0 lin.m/m2 at 120mm headlap (net)
Batten size 38 x 25mm for rafters/supports recommended not exceeding 450mm centres (fixed to BS 5534) 50 x 25mm for rafters/supports not exceeding 600mm centres
Tile nails 38 x 3.35mm
Fixing clips Eaves, verge and tile clips
Authority BS EN 1304
* The minimum recommended pitch and lap may be influenced by special circumstances, please contact the Technical Advisory Service.
370
247
A
B
DE
F
C G
J
H
K
N
375
80
240
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 98 Lincoln clay pantiles
Half round ridge tile
Third round hip tile Third round hip end tile
Left hand verge tile
Dentil slip
Half round ridge end tile
Ventilation tile
Lincolnclay fittings and accessories
• Universal HipFast system (6m)
• Universal HipFast support tray (6m)
• RidgeFast/HipFast union pack (6 No. unions)
• Universal 10mm eaves vent system (6m)
• Universal 25mm eaves vent system (6m)
• Comb filler strip
• Continuous rafter roll (2 x 6 m)
• Gutter spacers (20 per pack)
• Lead support strip (1.5m)
• Dry ridge batten section (3m)
• Dry ridge batten section (3m)
• Lincoln filler unit vented
• High profile GRP valley trough (3m)
• Accommodates up to 20° pitch difference either side of valley
• Suitable on rafter pitches from 17.5° to 60°
• Universal RidgeFast system (6m)
• RidgeFast blanking tape (2 x 2 m)
• RidgeFast/HipFast union pack (6 No. unions)
Dry fix ventilation and accessoriesThe following products and accessories can be used with Lincoln clay fittings. Our website also contains further information about dry fix and ventilation solutions: www.marleyeternit.co.uk/dryfix Note: Minimum and maximum pitches may vary – please contact our Technical Advisory Service for more information.
Universal eaves vent system
Top abutment ventilation systemUniversal GRP dry valley
Universal RidgeFast system Universal HipFast system
• Mortar bedded security hip kit
• Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityhip or scan the QR code shown
• Mortar bedded security ridge kit
• Watch a quick video on mortar bedded security fixing at marleyeternit.co.uk/securityridge or scan the QR code shown
Security fixingMortar bedded security ridge and hip fixing kits are available to meet the latest British Standards and NHBC guidelines.Note: Minimum and maximum pitches may vary – please contact our Technical Advisory Service for more information.
Mortar bedded security ridge Mortar bedded security hip
375
120
270
370
247
370
247
90
150
385
120
270
80
385
240
All dimensions in mm.
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 1110 Lincoln clay pantiles
LincolnDesign detailing
Universal eaves ventilation> eaves ventilation to satisfy 10mm or 25mm conditions
> eaves to ridge ventilation for pitches of 17.5°-70°
> continuous rafter roll compresses insulation to allow free air passage (use two rolls to compress deep insulation)
> strip ventilator has discreet ventilation grille and is nailed to fascia or timber fillet
> suitable with or without soffit board
> use comb filler strip with deep profiled tiles
> mechanically fix all tiles at eaves
Lincoln clay pantile
10/25mm over fasciastrip ventilator
Continuous rafterroll (2 No.)
Maximum gauge 295mm
Tiling fillet
Bedded verges> ensure undercloak does not tilt towards gable
> verge overhang should be a maximum of 50mm
> use Lincoln left hand verge tile for left hand verges
> mechanically fix all verge tiles in accordance with BS 5534
Lincoln verge clip
Fibre cement undercloak
Tiling batten
Underlay
Lincoln clay pantile
Mortar bedding
Third round hip tile
Ridge union clamp
Ridge union
Ridge roll flashing
Lincoln clay pantile
Ridge batten bracket
Hip batten brackets
Mortar bedded hips> maximum rafter pitch 45°
> fix hip units to hip tree using ridge clamp and 100mm stainless steel screw
> complete hip at ridge apex with three way mitre
Universal HipFast system> provides additional ventilation to the roof void when a 5mm gap in the underlay is used in conjunction with either eaves or ridge ventilated systems or ventilation tiles
> use one or two thicknesses of 50mm x 25mm batten to fit batten brackets
> use hip end hip tile at eaves
> mechanically fix each hip tile via hip unions and clamps
> complete hip at ridge with soaker flashing
For more information on security hip fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityhip
Tiling batten
Underlay
Lincoln clay pantileLincoln left hand verge tile
Fibre cement undercloak
Lincoln verge clip
Mortar bedding
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 1312 Lincoln clay pantiles
Universal GRP dry valley> minimum rafter pitch 17.5°, maximum 60°
> maximum valley length 8m
> suitable for all plan angles and where the pitch either side of the valley varies by a maximum of 20°
> provide continuous support for valley trough using 19mm timber ply boards inset between rafters or 6mm continuous ply boards laid over rafters
> tightly butt tiles or slates to central upstand of valley units to prevent ingress of birds or vermin
> provide metal apron at foot of valley and dress into gutter at eaves. For rafter pitches below 25° cut fascia board to maintain valley pitch
> nail or clip adjacent tiles to the valley
> complete top of valley with a lead saddle
Battens at max 295mm gauge Lincoln clay pantiles cut to angle of valley
Lincoln clay pantile
Underlay
Rafter
19mm (min) timber valley board
High profile dry valley trough
Tiling batten
Design detailing
Universal RidgeFast system> provides 5,000mm2/m free vent area at ridge apex
> ensure gap is provided in roof underlay to vent roof void
> use one or two thicknesses of 50mm x 25mm batten to fit
batten brackets
> mechanically fix all top course tiles
> use ridge end tile
Half round ridge tile
Ridge union clamp
Ridge union
Ridge roll flashing
Lincoln clay pantile
Ridge batten bracket
Underlay cut to provide insulation
Mortar bedded ridges> security ridge fixing kits are available for Lincoln clay ridges
> maximum rafter pitch 50°
> fix ridge units to ridge batten using ridge clamp and 100mm stainless steel screw
> mechanically fixes ridge tile in line with BS 5534 fixing guidelines
For more information on security ridge fixing kits, including installation videos, you can scan the QR code or visit: marleyeternit.co.uk/securityridge
14 Lincoln clay pantiles
Resources
Technical adviceOur Technical Advisory Service is staffed by a qualified team with specialist knowledge. Call 01283 722588 or e-mail [email protected]
Fixing instructions and literature Comprehensive sitework, fixing and installation literature and videos: marleyeternit.co.uk/resources
All current product and technical literature can be downloaded: marleyeternit.co.uk/downloads
SamplesSamples of clay interlocking and plain tiles, fibre cement slates and concrete tiles are available on request. Tel 01283 722588 marleyeternit.co.uk/samples
Stockist informationTo find details for stockists of Marley Eternit products, visit: marleyeternit.co.uk/stockists
Customer servicesKnowledgeable and friendly staff are available to offer quotations, expert advice, deal with orders and all other enquiries. Call 08705 626400 or e-mail [email protected]
Sales supportOur Area Sales Managers have in-depth knowledge of your local area. They are available to visit your site to carry out a roof survey, and to offer specific solutions for both new build and refurbishment projects. marleyeternit.co.uk/localcontacts
TilefixTo request a fixing specification based on the geographical location and building dimensions of specific building projects. Call 01283 722588 or e-mail [email protected]
EstimatorTo request a complete bill of materials for your roofing project: Call 01283 722588 or e-mail [email protected]
Training centreWe have a purpose-built training centre where we are able to impart our expertise through a range of practical and classroom courses. To find out more about our courses, visit: marleyeternit.co.uk/training
Health and SafetyIn line with the requirements of the Health and Safety at Work Act, The Consumer Protection Act and The Chemicals (Hazard Information and Packaging for Supply) Regulations and the Control of Substances Hazardous to Health Regulations, please download and view copies of our COSHH data sheets at marleyeternit.co.uk/coshh
Design detailing
Abutment> maximum rafter pitch 45° (55° using steep pitch batten section)
> provides 5,000mm2/lin.m ventilation
> ensure air passage from roof void is not obstructed
> mechanically fix all top course tiles
> use minimum 1.5m length of lead flashing with 150mm side laps
Underlay
Code 4 lead
Lead support strip
Lincoln ventilatedfiller unit
Lincoln clay pantile
Dry ridgebatten section
Underlay cut back5mm min. to provideventilation
Min.75mm
Batten
Lincoln clay tile vent> locate clear of rafters
> use spigot-soaker tray to weather the offset hole in underlay
> locate at 1.3-1.5m centres for 5,000mm2/lin.m ventilation and 565-765mm centres for 10,000mm2/lin.m ventilation
Underlay
Nailed fixing to back of batten
‘V’ cut in felt with flap nailed to batten
Battens at max. 295mm gauge
Lincoln clay pantile
Lincoln clay tile vent
50mm air gap maintained over insulation
For advice, literature and samples Tel 01283 722588 or visit marleyeternit.co.uk 15
Call 01283 722588 Email [email protected] Or visit www.marleyeternit.co.uk
Marley Eternit Lichfield Road Branston Burton upon Trent DE14 3HD