Marlin 1894 & 189:Takedown Guide

Clean your own gun with confidence.Saves you money on repairs!

MADE EASY

Marlin 1894

Fo/>'

93

43 Magazine Tube Follower Spring44 1'4egznn6 Tube Plug45 Magazine Tube Plug Screw46 Rear Band47 Rear Band Screw48 Rear Sight Base49 Rear Sight Elevator50 Rear Sight Folding Leaf5l Receiver52 Peep Sight Dummy Screws53 Scope Mount Dummy Screws54 Sear55 Tang Screw56 Trigger

57 Trigger and Sear Pin58 Trigger Guard Plate59 Trigger Guard Plate Screw60 Trigger Guard Plate Support Screw6l Trigger Safety Block62 Trigger Safecy Block Pin63 Trigger Safety Block64 Trigger Guard Plate Latch Pin

I Barrel

2 Breech bolt

3 Bullseye4 Buttplate5 Buttplate Screws6 Buttplate Spacer

7 Buttstock Complete8 Carrier9 Carrier Rocker

l0 Carrier Rocker Pinll Carrier Rocker Spring12 Carrier Screw13 Ejector

14 Ejector Spring

15 Extractor with Spring16 Extractor Retaining Pinl7 Finger l-everl8 Finger Lever Plunger19 Finger Lever Plunger Pin20 Finger Lever Plunger Spring2l Finger Lever Screw

22 Firing Pin, Front23 Firing Pin, Rear24 Firing Pin Retaining Pins25 Firing Pin Spring26 Forearm27 Front Band28 Front Band Screw29 Front Sight3O Hammer3l HammerStrut32 HammerStrut Pin33 Hammer Screw34 Hamrner Spring

35 Hammer Spring Adjusring Plate36 Hammer Spur & Screw37 Hammer Spur Wrench38 Loading Gate

39 I-oadingGate Screw40 Locking Bolt4l Magazine Tube42 Magazine Tube Follower

29s'

9u.

WARNING:Make sure the gun isentirely unloaded beforestarting the disassembly;visually check some roundscan hide.

Read every instructioncarefully using the pictureonly as a reference.

27

\28

ts1

e23

17

;s

RADOCY1 800 3s6 47s9

sffq;

Copyright @2003 By Radocy Products, Co.

2. Drrftthe finger lever plunger pinout and remove the plunger and spring.

4. The ejector is lifted out of the receiver easily.Do not remove the spring unless for repairs.

L. Partially open the leverand take out the fineer leverscrew.

3. Remove the breech bolt from the rear. Depressthe hammer slightly to clear the breech bolt.

6. Drift out the middle pin torelease the front firing pin and

its flat spring.

8. Remove the tang screw. If the stock is tightbump it with the heel of your hand.

5. Drift out the roll pin in the rear of the bolt and removethe rear firing pin.

7. Driftthe extractor pin and remove the

extractor from the front of the bolt.

9. Depress the trigger safety blockand carefully lower the hammer to thefired position.

10. With pliers grip the hammer spring adjustingplate and tilt it forward and slide the lower edge outof the groove. Remove the plate and hammerspring out toward the rear.

L1. Remove the hammer screw.

L3. Use a small Alan wrench to take thehammer spur off.

12. Take the hammer out from the top of the receiver.Do not remove the pin in the hammer unless for repairs.

14. Take the trigger guard plate screwout.

1,5. Remove the trigger guard platesupport screw out.

L6. Move the trigger guardplate downward from the rear

first. Use a non-marringhammer lightly if it is a tight

fit.

Before disassembly note the relationship of parts.

17. Drrftthe out the triggerpin. Remove the trigger from the bottom of the plate. The sear can

be lifted off of the trigger.

L8. Drift the trigger safety block pin out and remove the springand safety block out of the plate.

)

L9. Pull the lockins bolt down out of the receiver.

20. Unscrew the carrier screw and remove thecarrier assembly out of the receiver. Further

disassembly of the carrier is not recoffrmended.

2l-. Unscrew the loading gate screw and remove

the loading gate from the receiver.

off toward the front.

23. To remove the front sight; unscrew the two verticalscrews of the front sight. Some models need to drift the frontsight insert out first, and then remove the two screws.

22. Slide the front hood sisht

24. tJnscrew the magazine fube plug screw. When the screw isremove hold on to the magazine tube plug and release it slowly.Remove the plug, spring and follower.

25. Remove the front andrear barrel band screws.

Slide the front and rear barrel band off toward the front.

NOT PICTURED: The forearm and magazine tube will slide off towards the front.

26. Unscrew the hex screw on the rear of thereceiver.

27. Remove the springand detent from the rear. Slide the safefy out toward the right.

During reassembly do not over tighten or the safety will not workproperly.

o ' q h a

The only difference on theModel 95 is the way the forearmis held in place. Remove the twoopposing screws on the forearmtip then pull the tip off towards

the front. The forearm tip tenon can be drifted out of the barrel if needed to release theforearm. Be sure to mark left and right on it. Some Model 94's may have the same set upfor the forearm.

Reassembly Tips:Line up the notch on the magazine tube andbarrel before replacing the front barrel band

and screw.

Hold the trigger back when replacing thehammer and hemmer pivot screw.

Place the hammer spring plate on the groovefirst then using pliers bring it forward into

place.

1 Barrel 2 Breech bolt 3 Bullseye 4 Buttpad with Spacer 5 Buttpad Screws (2) 6 Buttstock 7 Carrier 8 Carrier Rocker 9 Carrier Rocker Pin10 Carrier Rocker Spring11 Carrier Screw13 Ejector Spring14 Extractor15 Finger Lever16 Finger Lever Plunger17 Finger Lever Plunger Pin18 Finger Lever Plunger Spring19 Finger Lever Screw20 Firing Pin, Front21 Firing Pin, Rear22 Firing Pin Retaining Pins (2)23 Firing Pin Spring24 Forearm25 Forearm Tip with Swivel Stud26 Forearm Tip Tenon27 Forearm Tip Tenon Screws (2)

28 Front Sight29 Hammer30 Hammer Strut31 Hammer Strut Pin32 Hammer Screw33 Hammer Spring34 Hammer Spring Adjusting Plate35 Hammer Spur Screw36 Hammer Spur Wrench37 Loading Gate38 Loading Gate Screw39 Locking Bolt40 Magazine Tube41 Magazine Tube Follower42 Magazine Tube Follower Spring43 Magazine Tube Plug44 Magazine Tube Plug Screw45 Magazine Tube Stud46 Rear Sight Base47 Rear Sight Elevator48 Rear Sight Folding Base49 Receiver50 Peep Sight Dummy Screws (2)51 Scope Mount Dummy Screws (4)52 Sear53 Tang Screw

54 Trigger55 Trigger & Sear Pin56 Trigger Guard Plate57 Trigger Guard Plate Latch Pin58 Trigger Guard Plate Screw59 Trigger Guard Plate Support Screw60 Trigger Safety Block61 Trigger Safety Spring62 Trigger Spring Pin63 Swivels64 Swivel Stud