mcrp 4-11.3m w ch 1 rigging high-mobility multipurpose ... 4-11.3m w c… · 10 12 14. fm...
TRANSCRIPT
FM 4-20.117/TO 13C7-1-111
7-8
Figure 7-5. Turret Support Placed and Secured
1 Construct the turret support as shown in Figure 3-2 of this manual.
2 Center the turret support under the turret at a 45-degree angle, in a left front to right reardirection.
3 Tie the turret support to convenient points on the turret with 1/2-inch tubular nylon webbing.
4 Tie the weapon station brake in the DOWN position with type III nylon cord.
5 Secure the three turret latches to holes in the turret ring with type III nylon cord.
2
3
3
4
5
FM 4-20.117/TO 13C7-1-111
7-9
Figure 7-6. Ammunition and Refrigerator Area Prepared
1 Place the stretcher in front of the cargo bed boxes and secure it to the front cargo bed ringswith type III nylon cord.
2 Place two 30-foot lashing across the truck bed in front of the stretcher. Extend the lashingsdown into the passenger seat footwells.
3 Place a 3/4- by 21- by 25-inch piece of plywood in the left rear passenger seat footwell.
4 Place a 3/4- by 21- by 30-inch piece of plywood in the right rear passenger seat footwell (notshown).
1
2
2
3
FM 4-20.117/TO 13C7-1-111
7-10
1 Place seventeen 5.56-mm ammunition cans in the left footwell over the plywood.
2 Place eighteen 5.56-mm ammunition cans in the right footwell over the plywood.
3 Set the refrigerator on an 11- by 22-inch piece of honeycomb in front of the stretcher andbetween the stacks of ammunition boxes.
4 Pass the lashings placed in Figure 7-6, step 2 over the ammunition boxes. Pass the lashingsthrough the box carrying handles whenever possible. Secure the lashings with load binders inthe front and rear of the refrigerator.
5 Tie a length of 1/2-inch tubular nylon webbing to the ring behind and inside the driver's seat.Pass the webbing over the refrigerator, and tie it securely to the ring on the inside front of theright rear passenger seat.
6 Tie a length of 1/2-inch tubular nylon webbing to the ring behind and inside the front passengerseat. Pass the webbing over the refrigerator, and tie it securely to the ring on the inside front ofthe left rear passenger seat.
Figure 7-7. Ammunition and Refrigerator Stowed
1
2
4
3
5
6
Note: Ammunition boxes should be wellpadded with felt or cellulose wadding.Padding is not shown here for purposesof clarity.
FM 4-20.117/TO 13C7-1-111
7-11
7 Pass a lashing through both rings behind the right passenger seat, up over the ammunitionboxes, and through both rings behind the left rear passenger seat. Secure the lashing with aload binder on top of the boxes.
8 Pass a lashing through both rings behind the driver's seat, up over the ammunitionboxes, and through both rings behind the right rear passenger seat. Secure the lashing with aload binder on top of the boxes.
Figure 7-7. Ammunition and Refrigerator Stowed (continued)
7
8
FM 4-20.117/TO 13C7-1-111
7-12
Figure 7-8. Machine Gun and Mount Stowed and Secured
1 Remove the barrel from the 50-caliber machine gun. Wrap the barrel and the gun with cellulosewadding and tape in place.
2 Secure the machine gun and barrel to the radio mount with 1/2-inch tubular nylon webbing.
3 Place the machine gun mount in the front passenger seat with the post facing the rear on theoutboard side. Pass 1/2-inch tubular nylon webbing around the top of the mount, and cross thetwo ends of the webbing above the post. Bring the ends of the webbing through the ringsbeside the seat, and tie the webbing to the box in the front.
1
3
2
FM 4-20.117/TO 13C7-1-111
7-13
Figure 7-9. Honeycomb Roof Cover and Body Sideboards Installed
1 Cover the roof with four full sheets of honeycomb. Crush or cut the bottom layer to allow forthe turret. Tape the upper layer. Secure the honeycomb to the roof with type III nylon cord.
2 Construct the body side boards and secure them to the truck as shown in FM 4-20.117/ TO13C7-1-111, Figure 2-13.
LIFTING AND POSITIONING TRUCK AND INSTALLING OPTIONAL DRIVE-OFF AIDS
7-5. Install the optional drive-off aids on the platform as shown in Figure 2-15.Install lifting slings on the truck and position the truck on the platform asshown in Figure 2-16. Attach the drive-off aids to the wheels as shown in Figure2-17.
LASHING TRUCK
7-6. Lash the truck to the platform with fifteen 15-foot tie-down assemblies.Install the lashings according to FM 4-20.102/TO 13C7-1-5, and as shown inFigures 7-10 and 7-11.
1
2
FM 4-20.117/TO 13C7-1-111
7-14
Figure 7-10. Lashings 1 Through 9 Installed
gnihsaL gnihsaL gnihsaL gnihsaL gnihsaLrebmuN
nwod-eiT nwod-eiT nwod-eiT nwod-eiT nwod-eiTsivelC
rebmuN snoitcurtsnI snoitcurtsnI snoitcurtsnI snoitcurtsnI snoitcurtsnI
123456789
1A1
2A23A3
4A4
A5dna5
:gnihsalssaP.gnirpsliocraertfeldnihebtekcarbnwod-eithguorhT
.gnirpsliocraerthgirdnihebtekcarbnwod-eithguorhT.elkcahsgnitfilraertfelhguorhT
.elkcahsgnitfilraerthgirhguorhT.mralortnocrewolraertfeldnuorA
.mralortnocrewolraerthgirdnuorA.gnirpsliocraertfelfotnorfnitekcarbnwod-eithguorhT
.gnirpsliocraerthgirfotnorfnitekcarbnwod-eithguorhT.gnir-DnwostihguorhtdnaA5sivelchguorhtgnihsaltoof-51assaP
sivelcotgnihsalehthcattA.2kcatsnielohehthguorhtgnihsalehtssaP.rednibdaolahtiw5
1235 4
12
1A2A
13
5
7
9
1
2
34
FM 4-20.117/TO 13C7-1-111
7-15
Figure 7-10. Lashing 10 Through 11 Installed
gnihsaL gnihsaL gnihsaL gnihsaL gnihsaLrebmuN
nwod-eiT nwod-eiT nwod-eiT nwod-eiT nwod-eiTsivelC
rebmuN snoitcurtsnI snoitcurtsnI snoitcurtsnI snoitcurtsnI snoitcurtsnI
011121314151
6A6
7A79A9
:gnihsalssaP.gnirpslioctnorftfeldnihebtekcarbnwod-eithguorhT
.gnirpslioctnorfthgirdnihebtekcarbnwod-eithguorhT.mralortnocrewoltfeldnuorA
.mralortnocrewolthgirdnuorA.liaremarftfelfodnenotekcarbnwod-eithguorhT
.liaremarfthgirfodnenotekcarbnwod-eithguorhT
679
10
12
14
FM 4-20.117/TO 13C7-1-111
7-16
Figure 7-12. Cargo Parachutes Installed
INSTALLING AND SAFETY TYING SUSPENSION SLINGS
7-7. Install and safety tie four 16-foot (2-loop), type XXVI nylon suspension slingsaccording to FM 4-20.102/TO 13C7-1-5, and as shown in Figure 2-20.
STOWING CARGO PARACHUTES
7-8. Use three G-11 cargo parachutes on this load. Stow the cargo parachutesaccording to FM 4-20.102/TO 13C7-1-5, and as shown in Figure 7-12.
1 Place and cluster three G-11 cargo parachutes on the honeycomb over the truck hood accord-ing to FM 4-20.102/TO 13C7-1-5.
2 Tie the front restraint straps to clevises 8 and 8A.
3 Tie the rear restraint straps to the 27th bushings on each side of the platform.
8
1
23
FM 4-20.117/TO 13C7-1-111
7-17
Figure 7-13. M-1 Cargo Parachute Release Installed
INSTALLING PARACHUTE RELEASE
7-9. Prepare and install an M-1 cargo parachute release according to FM 4-20.102/TO 13C7-1-5, and as shown in Figure 7-13.
1 Place the M-1 release on the roof honeycomb in front of the parachutes.
2 S-fold the slack in the suspension slings. Tie the folds with type I, 1/4-inch cotton webbing.
3 Attach the suspension slings and the riser extensions to the release. Tie the release to conve-nient points on the load with type III nylon cord.
1
3
2
2
FM 4-20.117/TO 13C7-1-111
7-18
INSTALLING EXTRACTION SYSTEM
7-10. Install the EFTC extraction system with a 16-foot release cable accordingto FM 4-20.102/TO 13C7-1-5, and as shown in Figure 2-23.
INSTALLING PROVISIONS FOR EMERGENCY RESTRAINTS
7-11. Install the provisions for emergency restraints on the load according to FM4-20.102/TO 13C7-1-5.
PLACING EXTRACTION PARACHUTE
7-12. Select the extraction parachute and extraction line needed using theextraction line requirements table in FM 4-20.102/TO 13C7-1-5. Rig theextraction line in an extraction line bag according to TM 10-1670-286-20/TO13C5-2-41. Place the extraction parachute and extraction line on the load forinstallation in the aircraft.
MARKING RIGGED LOAD
7-13. Mark the rigged load according to FM 4-20.102/TO 13C7-1-5, and asshown in Figure 7-14. Complete Shipper's Declaration for Dangerous Goodsaccording to AFJMAN 24-204/TM 38-250. If the load varies from the one shown,the weight, height, CB, and parachute requirements must be recomputed.
EQUIPMENT REQUIRED
7-14. Use the equipment listed in Table 7-1 to rig this load.
FM 4-20.117/TO 13C7-1-111
7-19
Figure 7-14. Ground Mobility Vehicle Rigged for Low-Velocity Airdrop
Weight: Load shown ...................................................................................... 12,420 pounds Maximum load allowed .......................................................................... 14,750 pounds
Height (with three G-11 parachutes) ...................................................................... 94 inchesWidth.............. ................................................................................................... 108 inchesLength (overall) ................................................................................................... 210 inches
Overhang: Front ............................................................................................... 0 inchesRear (EFTC)..............................................................................18 inches
CB (from front edge of platform) ............................................................................ 96 inches
CB
CAUTIONMake the final rigger inspection required by FM 4-20.102/TO 13C7-1-5
before the load leaves the rigging site.
FM 4-20.117/TO 13C7-1-111
7-20
Table 7-1. Equipment Required for Rigging Ground Mobility Vehicle for Low-Velocity Airdrop
kcotSlanoitaN kcotSlanoitaN kcotSlanoitaN kcotSlanoitaN kcotSlanoitaNrebmuN metI metI metI metI metI ytitnauQ ytitnauQ ytitnauQ ytitnauQ ytitnauQ
3178-372-00-0408 lag-1,etsap,evisehdA deriuqersA
4535-090-00-0304 )egral(ni-1,noisnepsus,sivelC 5
6412-042-00-0204 bl-055,IIIepyt,nolyn,droC deriuqersA
5875-434-00-0761 htiwrefsnartecrofnoitcartxe,pordria,ylbmessagnilpuoCtf-61,elbac
1
8230-063-00-0761:revoC
egral,sivelC 1
8596-466-00-5318 gniddawesolullec,gnigakcap,lairetamgninoihsuC deriuqersA
5863-859-00-5038 kcihtni-2/1,tleF deriuqersA
8762-381-10-0761 )gabenil(enilnoitcartxe,faeL 2
2544-460-10-0761)71-Crof(eugord,eniL
IVXXepyt,)pool-1(tf-06 1
3136-260-10-07611567-701-10-0761
3136-260-10-07611567-701-10-0761
1567-701-10-0761
:noitcartxe,eniLIVXXepyt,)pool-3(tf-06:031-CroFIVXXepyt,)pool-3(tf-041:141-CroF
:5-CroFdnaIVXXepyt,)pool-3(,tf-06
IVXXepyt,)pool-3(tf-041:71-CroF
IVXXepyt,)pool-3(tf-041
11
11
1
4998-534-00-60355615-232-00-01353591-300-00-07614143-700-00-5635
:ylbmessAkniL:tniop-owT
gnolni-4,maidni-1,tloBlanogaxeh,ni-1,tuN
ni-4/33,edis,etalPegral,recapS
4)8()8()8()8(
6416-022-00-01558446-022-00-01554726-022-00-0155
:rebmuLni-4yb-2ni-6yb-2ni-4yb-4
deriuqersAderiuqersAderiuqersA
9564-010-00-5135 d8,eriwleets,liaN deriuqersA
FM 4-20.117/TO 13C7-1-111
7-21
Table 7-1. Equipment Required for Rigging Ground Mobility Vehicle for Low-Velocity Airdrop(continued)
kcotSlanoitaN kcotSlanoitaN kcotSlanoitaN kcotSlanoitaN kcotSlanoitaNrebmuN metI metI metI metI metI ytitnauQ ytitnauQ ytitnauQ ytitnauQ ytitnauQ
8293-357-00-0761 )bmocyenoh(gnitapissid-ygrene,daPni-69yb-63yb-3
steehs31
1487-610-10-0761
6173-360-10-0761
5173-360-10-0761
:etuhcaraP:ograCB11-G
:noitcartxeograC).71-Chtiwesurofkcolb-HddA(tf-22
)71-Crof(eugorDtf-51
2
1
1
5248-353-10-07612732-261-10-07616732-261-10-07611832-261-10-0761
tf-61,Vepyt,pordria,mroftalPCTFE,ylbmessatekcarB
Vepyt,ylbmessasivelCnoitcartxe,ylbmessatekcarB
)knilesoprupitluM(ylbmessaknilmednaT
)1()02(
)1()4(
1894-821-00-0355 ni-4/3,doowylP steehs3
6188-790-10-0761 1-M,etuhcarapograc,esaeleR 1
1677-360-10-0761
4036-260-10-07613036-260-10-0761
4036-260-10-0761
2036-260-10-0761
pordria,ograc,gnilS:noisnepsusroF
gnibbewnolynIVXXepyt,)pool-2(tf-61:gnitfilroF
gnibbewnolynIVXXepyt,)pool-2(tf-9gnibbewnolynIVXXepyt,)pool-2(tf-21
:tnemyolpedroFgnibbewnolynIVXXepyt,)pool-2(tf-9
:noisnetxeresirroFgnibbewnolynIVXXepyt,)pool-2(tf-02
4
22
1
6
9128-040-00-0435 sevink3/wsemoc,tuc-itlum,esaeleretuhcarap,partS 2
6105-662-00-0157 ni-2,evisehda,epaT deriuqersA
1720-739-00-0761 toof-51,ylbmessanwod-eiT 82
5280-443-10-0761 diaffo-evirdelciheV 1
1142-862-00-50382575-280-00-50381953-362-00-5038
:gnibbeWIepyt,ni-4/1,nottoCni-2/1,ralubut,nolyN
IIIVepyT
deriuqersAderiuqersAderiuqersA
ACB attitude control barAD airdrop
AFB Air Force base AFJMAN Air Force Joint Manual AFR Air Force regulation AFTO Air Force technical order ALC Airlift Logistics Center
attn attentionBCS battery computer system
C changecap capacityCB center of balance
CDU computer display unit chap chapter
d pennyDA Department of the ArmyDC District of ColumbiaDD Department of Defense
diam diameterDSVT digital subscriber voice terminal
DVE driver vision enhancer EFTC extraction force transfer coupling
EPW enemy prisoner-of-war fig figureFM field manual ft foot/feetgal gallon
GLPS gun laying positioning systemGPS global positioning system
G/VLLD ground/vehicle laser locator designatorHQ headquarters
Glossary-1
GLOSSARY
HMMWV high-mobility, multipurpose, wheeled vehicleIFSAS initial fire support automated system
in inchJAI joint airdrop inspector
LAW light anti-tank weapon lb pound
LSS light-scattering screenLD/R laser designator/rangefiner
LTACFIRE lightweight tactical fire direction system
MCRP Marine Corps Reference Publicationmm millimeter
MOPP mission oriented protective postureMRE meal, ready-to-eat
NSN national stock numberPADS position and azimuth determining system
PDB power distribution boxPLU program load unit
OVE on-vehicular equipmentSMS semi-automatic meteorological sensorSTIK soft-top installation kit
TACCS tactical army combat service support computer systemTM technical manualTO technical order
TRADOC US Army Training and Doctrine CommandUS United States
w with yd yard
Glossary-2
LV low-velocityLVOSS light vehicle obscuration smoke system
22 July 2005 References-1
C1, FM 4-20.117/MCRP 4-11.C/TO 13C7-1-111
REFERENCES
AR 59-4/ Joint Airdrop Inspection Records, Malfunction InvestigationsOPNAVINST 4630.24C and Activity Reporting. 1 May 1998.
AFJ 13-210(I)/MCO 13480.1B
AFMAN 24-204(I)/ Preparing Hazardous Materials for Military Air Shipments.TM 38-250/NAVSUP 11 December 2001
PUB 505/MCO 4030.19H
FM 4-20.102/ Airdrop of Supplies and Equipment: Rigging Airdrop Platforms.MCRP 4-11.3J/ 29 August 2001
NAVSEA SS400-AB-MMO-010/TO 13C7-1-5
FM 4-20.153/ Airdrop of Supplies and Equipment: Rigging Ammunition.MCRP 4-11.3B/ 1 May 2004TO 13C7-18-41
TM 9-2320-280-10/ Operator's Manual for Truck, 1 1/4-ton. 31 January 1996TO 36A-12-1A-2091-1/
TM 2320-10/6B
TM 10-1670-268-20&P/ Organizational Maintenance Manual Including Repair Parts andTO 13C7-52-22 Special Tools List for Type V Airdrop Platform and Dual Row Row
Airdrop Platform. 15 September 2002.
TM 10-1670-277-23&P/ Unit and Direct Support (DS) Maintenance Manual IncludingTO 13C5-28-2/ Repair Parts and Special Tools List for Parachute, Cargo Type,
NAVAIR 13-1-30 28-ft Diam, Cargo Extraction. 30 April 2002.
TM 10-1670-278-23&P/ Unit and Intermediate Direct Support (DS) Maintenance ManualTO 13C5-26-2/ Including Repair Parts and Special Tools List for Parachute,
NAVAIR 13-1-27/ Cargo Type, 15-ft Diam, Cargo Extraction. 31 December 2004.TM 01109C-23&P/1
TM 10-1670-279-23&P/ Unit and Intermediate Direct Support (DS) Maintenance ManualTO 13C5-27-2/ Including Repair Parts and Special Tools List for Parachute,
NAVAIR 13-1-28 Cargo Type, 22-ft Diam, Cargo Extraction. 30 August 1989.
TM 10-1670-280-23&P/ Unit and Intermediate Direct Support (DS) Maintenance ManualTO 13C5-31-2/ Including Repair Parts and Special Tools List for Parachute,
NAVAIR 13-1-31 Cargo Type, G-11A, G-11B, and G-11C. 15 September 2002.
TM 10-1670-286-20/ Unit Maintenance Manual for Extraction Line PanelTO 13C5-2-41 (Including Stowing Procedures). 15 March 2001.
References-2 22 July 2005
C1, FM 4-20.117/MCRP 4-11.3M/TO 13C7-1-111
AFTO Form 22 Technical Order Publication Improvement Report
DA Form 2028 Recommended Changes to Publication and Blank Forms.
FM 4-20.117 (FM 10-517) TO 13C7-1-111 1 OCTOBER 2001
By Order of the Secretary of the Army and the Air Force:
ERIC K. SHINSEKIGeneral, United States Army
Chief of Staff
Official:
JOEL B. HUDSONAdministrative Assistant to the
Secretary of the Army 0127102
GEORGE T. BABBITT MICHAEL E. RYANGeneral, USAF General. USAFCommander, AFMC Chief of Staff
DISTRIBUTION:
Active Army, Army National Guard, and U.S. Army Reserve: To be distributed in accordancewith the initial distribution number 113833, requirements for FM 4-20.117.
PIN: 079320-001